MCQ's On Jigs & Fixtures
MCQ's On Jigs & Fixtures
MCQ's On Jigs & Fixtures
7. Principle of ______ states that “In order to achieve the maximum accuracy in location the
locating points should, therefore, be placed as far apart from one another as it is possible”.
a) Six point location
b) Least points
c) Extreme positions
d) Mutually perpendicular planes
8. The following holds the workpiece securely in a jig or fixture against the cutting forces
a) Locating device
b) Clamping device
c) Guiding device
d) Indexing device
10. The following material is commonly used for making locating and clamping devices
a) High carbon steel
b) Low carbon steel
c) High speed steel
d) Die steel
11. The following type of jig is used for machining in more than one plane
a) Template jig
b) Plate type jig
c) Open type jig
d) Box type jig
12. The following type of jig suits best for drilling of holes in hollow cylindrical components,
with relatively smaller outside and inside diameters, such as bushes
a) Solid type jig
b) Pot type jig
c) Box type jig
d) Open type jig
13. The following type of jig is used to drill a series of equidistant hole along a circle
a) Index jig
b) Plate type jig
c) Open type jig
d) Pot type jig
14. This type of jig is employed on multi-spindle machines
a) Index jig
b) Universal jig
c) Open type jig
d) Multi-station jig
15. The following jig can be used for several different work pieces and operations
a) Template jig
b) Multi-station jig
c) Index jig
d) Universal jig
18. V-blocks (Vee locators) are used for clamping as well as locating when faces are inclined
upto
a) 30o
b) 12o
c) 9o
d) 3o
19. Which type of Support pin or rest button is shown in below diagram?
a) Fixed type support pin
b) Adjustable type support pin
c) Support pad
d) Wedge type support pin
21. A device, in which a component is held and located for a specific operation and bushes are
integrated that guide the tool, is called as
a) Jig
b) Fixture
c) both a. and b.
d) none of the above
24. Which of the following sentences are true for jigs and fixtures?
1. Using jigs and fixture produce work rapidly
2. High speed, feed and depth of cut can be used in machining with the help of jigs and
fixtures
3. Jigs and fixture cannot be used in machining of complex and heavy components
a) (1) and (2)
b) (2) and (3)
c) (1) and (3)
d) All of the (1), (2) and (3)
25. The device which place the workpiece in the same position, in jig and fixture, cycle after
cycle is called as
a) placing device
b) fixing device
c) locating device
d) positioning device
26. Which fixtures are used for machining parts which must have machined details evenly
spaced?
a) Profile fixtures
b) Duplex fixtures
c) Indexing fixtures
d) None of the above
27. The device which is used to remove workpiece from close-fitting locators, after the
workpiece has been removed is called as
a) Remover
b) Ejector
c) escaper
d) blocker
28. With the use of Jigs and fixture total cost of production
a) Increases
b) Decreases
c) Remains same
d) Jigs are not used in any production process
29. With the use of Jigs and fixture rate of production will
a) Increase
b) Decrease
c) Remains same
d) Jigs are not used in any production process
32. With the use of Jigs and fixture quality control expenses will
a) Reduce
b) Increases
c) Jigs and fixture are not used in any production process
d) None of the mentioned
41. Common feature between jig and fixture is that both are used for
a) cutting the work piece
b) holding the work piece
c) locating the work piece
d) testing and inspection of the work piece