JIGS & FIXTURE MCQ

1) Jigs primary purpose to provide

a) Accuracy
b) Limit
c) Fits
d) None of these
2) Jig is used for ___________
a) Locating
b) Supporting
c) Holding
d) All of these
3) A drill jig is used for _____
a) Drilling
b) Repetitive hole
c) Locating
d) None of these
4) With the use of Jigs and fixture total cost of production
a) Increase
b) Decrease
c) Remain same
d) None of these
5) With the use of Jigs and fixture rate of production will
a) Increase
b) Decrease
c) Remain same
d) None of these
6) Jigs and fixture increases the accuracy of the parts.
a) True
b) False
7) Jigs And fixture are used to provide interchangeability.
a) True
b) False
8) With the use of Jigs and fixture quality control expenses will
a) Reduce
b) Increases
c) Jigs and fixture are not used in any production process
d) None of the mentioned
9) With the use of Jigs and fixture
a) Labour cost decreases
b) Labour cost increases
c) Labour cost decreases
d) None of the mentioned
10) Which of the following is not correct about fixture?
a) It is used to hold the work
b) It is used to position the work the work
 JIGS & FIXTURE MCQ
c) It assures high accuracy of parts
d) It is used to guide the cutting tool
11) Which of the following is not correct about jig?
a) It is used to hold the work
b) It is used to position the work the work
c) It is used to guide the cutting tool
d) None of the mentioned
12) In which of the following operation jigs are preferred over fixture?
a) Drilling
b) Turning
c) Milling
d) Grinding
13) Number of degree of freedom of a workpiece in space is equal to
a) 10
b) 12
c) 14
d) 16
14) Jigs and Fixtures are used for
a) Mass production
b) Identical parts production
c) Both ‘A’ and ‘B’
d) None of the above
15) The use of jigs and fixtures
a) Facilitates deployment of less skilled labour for production
b) Eliminates pre-machining operations like marking, measuring, laying out etc.
c) reduced manual handling operations
d) All of the above
16) A fixture does not
A) Holds the workpiece
B) Locate the workpiece
C) Guide the tool
D) All of the above
17) Jigs are not used in
A) Drilling
B) Reaming
C) Tapping
D) Milling
18) Fixtures are used in
A) Milling
B) Shaping
C) Turning
D) All of the above
19) Principle of ______ states that “In order to achieve the maximum accuracy in location the
locating points should, therefore, be placed as far apart from one another as it is possible”.
 JIGS & FIXTURE MCQ
A) Six point location
B) Least points
C) Extreme positions
D) Mutually perpendicular planes
20) The following holds the workpiece securely in a jig or fixture against the cutting forces
A) Locating device
B) Clamping device
C) Guiding device
D) Indexing device
21) The following is a quick acting clamp
A) Hinged clamp
B) Cam operated clamp
C) Bridge clamp
D) Edge clamp
22) The following material is commonly used for making locating and clamping devices
A) High carbon steel
B) Low carbon steel
C) High speed steel
D) Die steel
23) The following type of jig is used for machining in more than one plane
A) Template jig
B) Plate type jig
C) Open type jig
D) Box type jig
24) The following type of jig suits best for drilling of holes in hollow cylindrical components, with
relatively smaller outside and inside diameters, such as bushes
A) Solid type jig
B) Pot type jig
C) Box type jig
D) Open type jig
25) The following type of jig is used to drill a series of equidistant hole along a circle
A) Index jig
B) Plate type jig
C) Open type jig
D) Pot type jig
26) This type of jig is employed on multi-spindle machines
A) Index jig
B) Universal jig
C) Open type jig
D) Multi-station jig
27) The following jig can be used for several different work pieces and operations
A) Template jig
B) Multi-station jig
C) Index jig
 JIGS & FIXTURE MCQ
D) Universal jig
28) The following are the advantages of cast jigs or fixtures
A) No heat treatments are required for the cast jigs and fixtures
B) It prevents the occurrence of tool chatter in milling
C) If cast jigs or fixture drops down, they don’t get misaligned or de-shaped, although it may
break
D) All of the above
29) The jigs and fixtures can be constructed through
A) Casting
B) Fabrication
C) Welding
D) All of the above
30) The following is the source(s) for developing new or improved product
A) Research and Development department of the enterprise
B) Consumer suggestions and Complaints
C) Other competitive products in the market
D) All of the above
31) The ultimate objective of the product is
A) To provide a new look
B) Utilizing existing manpower
C) To monopolize the market
D) All of the above
32) V-blocks (Vee locators) are used for clamping as well as locating when faces are inclined up to
a) 300
b) 120
c) 90
d) 30
33) Which type of Support pin or rest button is shown in below diagram?

a) Fixed type support pin

b) Adjustable type support pin
c) Support pad
d) Wedge type support pin
34) Jigs and fixtures are
a) machining tools
b precision tools
c) both a. and b.
d) none of the above
 JIGS & FIXTURE MCQ
35) A device, in which a component is held and located for a specific operation and bushes are
integrated that guide the tool, is called as
a) jig
b) fixture
c) both a. and b.
d) none of the above
36) Fixtures are used in connection with
a) drilling operation
b) reaming operation
c) tapping operation
d) milling operation
37) How jigs are in terms of weight compared to fixtures?
a) Jigs are lighter than fixtures
b) Jigs are heavier than fixtures
c) Jigs are equal in weight to fixtures for same operation
d) cannot say
38) Which of the following sentences are true for jigs and fixtures?
1. Using jigs and fixture produce work rapidly
2. High speed, feed and depth of cut can be used in machining with the help of jigs and fixtures
3. Jigs and fixture cannot be used in machining of complex and heavy components
a). (1) and (2)
b) (2) and (3)
c) (1) and (3)
d) All of the (1), (2) and (3)
39) The device which place the workpiece in the same position, in jig and fixture, cycle after cycle is
called as
a) Placing device
b) fixing device
c) locating device
d) positioning device
40) Which fixtures are used for machining parts which must have machined details evenly spaced?
a) Profile fixtures
b) Duplex fixtures
c) Indexing fixtures
d) None of the above
41) The device which is used to remove workpiece from close-fitting locators, after the workpiece
has been removed is called as
a) remover
b) ejector
c) escaper
d) blocker
42) Lathe mandrels can be termed as a
a) Jig
b) Fixture
 JIGS & FIXTURE MCQ
c) Gauge
d) Template
43) Tolerance on jig should be
(a) 5% of the tolerance on the job
(b) 10% of the tolerance on the job
(c) 20 to 50% of the tolerance on the job
(d) 100% of the tolerance on the job
44) Which one of the following bushing is used to locate the renewable bushing
(a) Press fit bushing
(b) Liner bushing
(c) Special bushing
(d) Knurled bushing
45) Which among the following is a locate used for location from internal diameter
(a) Solid support
(b) Pin type locator
(c) vee locator
(d) nest locator
46) Which one of the following jigs consists of drill plate, which rests on the component to be
drilled?
(a) Solid jig
(b) Plate jig
(c) Box jig
(d) Trunnion jig
47) Which among the following jigs is used for location from a bore
(a) Plate jig
(b) Solid jig
(c) Post jig
(d) Box jig
48) Fixture is a production devices which
(a) Holds the workpiece
(b) Locates the workpiece
(c) Holds and locates the workpiece
(d) Neither holds nor locates the workpiece
49) Jig is a device which
(a) Locates the workpiece
(b) Holds and supports the workpiece
(c) Guides the cutting tool
(d) Does all the above
50) Drill jig bushings are generally made of
(a) Mild steel
(b) Cast iron
(c) Cast steel
(d) Tool steel
51) Which among the following locator is best suitable for location of a round shaped job
 JIGS & FIXTURE MCQ
(a) Pin type locator
(b) Wedge type locator
(c) Vee locator
(d) Adjustable stop locator
52) Which one of the following is used to clamp the job in relation to the tool in mass production
(a) Jig
(b) Fixture
(c) Housing
(d) Gauge
53) Which one of the following devices is used for the convenience of fabrication of a job by welding
which is set in this device so that it can be swiveled around 360° as per requirement
(a) Gauge
(b) Template
(c) jig
(d) Fixture
54) Which one of the following is used to guide the tool and hold the job in mass production
(a) Gauge
(b) Housing
(c) Jig
(d) Fixture
55) The relief or clearance at the cutting edge of a flat drill varies from\
a) 3° to 8
b) 20° to 30°
c) 60° to 90°
d) 90° to 120°
56) The usual value of the point angle of a drill is
A) 70°
B) 100°
C) 118°
D) 130°
57) The workpiece motion and tool motion respectively in a horizontal boring machine are.......
A) Stationary and rotational
B) Rotational and translational
C) Translational and rotational
D) Stationary and rotational with translation
58) The workpiece motion and tool motion respectively in vertical boring machine are.......
A) Stationary and rotational
B) Rotational and translational
C) Translational and rotational
D) Rotational with translation and stationary
59) V-block is a __________type of tool
A) Fixture
B) Jig
C) Jig bore
D) None of these
 JIGS & FIXTURE MCQ
60) Revolving Centre is known as _______
A) Dead Centre
B) Live Centre
C) Machining Centre
D) None of these
61) Revolving Centre is used for ________
A) Greater clamping pressure
B) Low clamping pressure
C) Rotation
D) None of these
62) is the most important element of a milling fixture
A) heavy base
B) flat and smooth surface
C) both a &b
D) none of these
63) The fixture is fastened to the machine table with the help of____________
A) T bolts engaging
B) V bolts
C) Round bolts
D) None of these
64) Setting block is made by which material
A) Mild steel
B) Carbide
C) Harden steel
D) None of these
65) In setting block the cutter should clear the feeler surfaces by at least __________cm to avoid
any damage
A) 0.08
B) 0.10
C) Both
D) None of these
66) In fixture Clamps should always operates from the _________side
A) Back
B) Front
C) Both side
D) None of these
67) Pressure of cut should always be ________side of the solid part of the fixture
A) Against
B) Opposite
C) Both a & b
D) None of these
68) Why should Clearance is provided in the jig or fixture body
A) to allow for any variation
B) to allow vibration
 JIGS & FIXTURE MCQ
C) both a and b
D) none of these
69) The use of __________devices to force the work piece out from the jig or fixture is important in
two positions.
A) Ejection
B) Ejector pin
C) Both a and b
D) None of these
70) Milling vice is a _______ type of work holding device
A) Fixture
B) Jig
C) Both of these
D) None of these
71) A fixture is a work-holding or support device used in the manufacturing industry
A) True
B) False
72) make sure that the workpiece rests in the correct position _____to consider
A) degrees of freedom
A) ejector pin
B) both a and b
C) none of these
73) what is the material of template drill jigs?
a) Mild steel
b) Hss
c) Cast iron
d) Harden steel
74) What is the use of template jig drill type ?
a) Enlarging the hole
b) Drilling
c) Both a &b
d) None of these
75) Template type drill jigs use for small production
a) True
b) False
76) Plate type jig use for large production
a) True
b) False
77) What is the material of drill bushes?
a) Hss
b) Mild steel
c) Harden steel
d) None of these
78) How many degree of freedom in a cubic workpiece
a) 12
 JIGS & FIXTURE MCQ
b) 6
c) 8
d) 10
79) How many liner degree of freedom in a workpiece
a) 12
b) 6
c) 8
d) 10
80) How many rotational degree of freedom in a workpiece
a) 12
b) 6
c) 8
d) 10
81) What is the percentages of tolerance should given to jig
a) 10% to 20%
b) 20% to 50%
c) 50% to above
d) None of these
82) What is the use of jig & fixture in total cost production
a) Remain same
b) Decrease
c) Increase
d) None of these
83) Jig & fixture increase the accuracy of part
a) True
b) False
84) With the use of jig & fixture quality control expense will
a) Low
b) High
c) Both a & b
d) None of these
85) Which of the following is not correct about fixture
a) It used to position the work
b) It used to hold the work
c) It assure high accuracy of part
d) It used to guide the cutting tool
86) Which of the following doesn’t uses a jig
a) Turning
b) Reaming
c) Tapping
d) Drilling
87) How jigs are in terms of weight compare to fixture
a) Jigs are lighter then fixture
b) Jigs are heavier then fixture
 JIGS & FIXTURE MCQ
c) Jigs are equal in weight to fixture
d) Cannot say
88) Which of the following is not correct about jig
a) It is used to hold the workpiece
b) It is used to position the workpiece
c) It is used to guide the cutting tool
d) None of the mention
89) ______________ concept ensure that all the six sigma freedom will get locked
a) 3-2-1
b) 4-2-3
c) Both a& b
d) None of these
90) How many type if drill jig are uses
a) 6
b) 5
c) 4
d) None of these
91) In channel jig tool is guided through the drill bush.
a) True
b) False
92) In open type the workpiece is placed on __________
a) The top
b) Bottom
c) Both a&b
d) None of these
93) Plate type jig is improvement of ________
a) Template type jig
b) Open type jig
c) Both a&b
d) None of these
94) Bushings are simple bearing sleeves inserted into these holes to protect them and guide
the _______
a) Workpiece
b) Drill bit
c) Both a &b
d) None of these
95) In fixture movable components known as ______
a) Clamps
b) Support
c) Both a &b
d) None of these
96) It used to hold or secure objects tightly together to prevent movement or separation through
the application of inward pressure is known as ______
a) Clamp
 JIGS & FIXTURE MCQ
b) Supporting
c) Guiding
d) None of these
97) The bench forms the fixed jaw is known as
a) Bench clamp
b) Rounded clamp
c) Both a & b
d) None of these
98) A magnetic base is a__________ based on a magnet that can effectively be turned "on" and
"off" at will; they are often used in optics and metalworking.
a) Magnetic fixture
b) Nonmagnetic fixture
c) Both a &b
d) None of these
99) fixtures are also used for drilling operations.
a) True
b) False
100) __________ is one which is used in a lathe where different cutting tools could be
accommodated in one set up
a) Adjustable fixture
b) Magnetic fixture
c) Both a & b
d) None of these
101) When extreme accuracy is required for grinding parts like connecting rods, valve faces or bevel
gears, __________are used
a) Grinding fixtures
b) Adjustable fixture
c) Assembly fixture
d) None of these
102) Large components in airplanes are usually assembled with___________
a) Assembly fixture
b) Grinding fixture
c) Adjustable fixture
d) None of these
103) The parts after getting finished with the manufacturing operation have to be checked for its
accuracy in shape or in dimension with ___________ fixture.
a) Inspection
b) Assembly
c) Both a &b
d) None of these
104) These elements locate the workpiece in proper position in relation to the cutting tool is known
as ___________
a) Assembly element
b) Locating elements
 JIGS & FIXTURE MCQ
c) Adjustable element
d) None of these
105) The elements locate the workpiece in proper position in relation to the cutting tool is known as
a) Clamping elements
b) Locating elements
c) Both a&b
d) None of these
106) These elements include different types of fastning devices, which are used in securing the jig or
fixture to the machine at proper position is known as
a) Locating elements
b) Positioning elements
c) Both a&b
d) None of these
107) Hydraulic Clamping Benefits are
a) Reduce setup time
b) Clamping constancy
c) Improve part quality
d) All of these
108) a pressure differential is created between the vacuum clamping plate and the workpiece is
known as
a) vacuum clamp
b) screw camp
c) both a& b
d) none of these
109) Materials used in Jigs and fixtures are
a) Harden steel
b) Carbide
c) Stainless steel
d) All of thee
110) With drill jigs, referencing is accomplished using
a) Drill bushing
b) Locating pin
c) Both a&b
d) None of these
111) With fixtures, referencing is accomplished using
a) Feeler gages
b) Drill bushing
c) Both a&b
d) None of these
112) If a cutter is improperly positioned relative to the fixture, the machined detail is also improperly
located.
a) True
b) false
113) locators must hold the workpiece ___________ to the cutting forces
 JIGS & FIXTURE MCQ
a) directly
b) against
c) both a &b
d) none of these
114) locate a workpiece from any surface is known as _________
a) plane locator
b) radial locator
c) both a&b
d) none of these
115) locate a workpiece from an internal or external diameter is known as
a) locating pin
b) concentric locator
c) plane locator
d) none of these
116) In many cases, locating is performed by a combination of the three locational methods is known
as_______
a) Radial locator
b) Plane locator
c) Combined locator
d) None of these
117) Restrict the movement of a workpiece around a concentric locator is known as ______
a) Concentric locator
b) Plane locator
c) Radial locator
d) None of these
118) Quick acting nut is used for
a) Round clamping
b) Rapid clamping
c) Both a & b
d) None of these
e)
119) clamping operation should be very simple and quick acting when the jig or fixture is to be used
more frequently and for large volume of work
a) true
b) false
120) ___________jigs are used to hold parts that are machined at right angles to their mounting
locators.
a) Angle plate
b) Surface plate
c) Both a &b
d) None of these