DJFPT MCQ
DJFPT MCQ
DJFPT MCQ
(Ans: C)
(B) Eliminates pre-machining operations like marking, measuring, laying out etc.
(Ans: D)
(B) Locating
(C) Guiding
(Ans: D)
(Ans: C)
(B) Reaming
(C) Tapping
(D) Milling
(Ans: D)
(B) Shaping
(C) Turning
(Ans: D)
7-Principle of ______ states that “In order to achieve the maximum accuracy in location the locating
points should, therefore, be placed as far apart from one another as it is possible”.
(Ans: C)
8-The following holds the workpiece securely in a jig or fixture against the cutting forces
(Ans: B)
(Ans: B)
10-The following material is commonly used for making locating and clamping devices
(Ans: A)
11-The following type of jig is used for machining in more than one plane
(Ans: D)
12-The following type of jig suits best for drilling of holes in hollow cylindrical components, with
relatively smaller outside and inside diameters, such as bushes
(Ans: B)
13-The following type of jig is used to drill a series of equidistant hole along a circle
(Ans: A)
(Ans: D)
15-The following jig can be used for several different work pieces and operations
(Ans: D)
(C) if cast jigs or fixture drops down, they don’t get misaligned or de-shaped, although it may break
(Ans: D)
17-The jigs and fixtures can be constructed through
(A) Casting
(B) Fabrication
(C) Welding
(Ans: D)
18. With the use of Jigs and fixture total cost of production
a) Increases
b) Decreases
c) Remains same
d) Jigs are not used in any production process
Answer: b
19. With the use of Jigs and fixture rate of production will
a) Increase
b) Decrease
c) Remains same
d) Jigs are not used in any production process
Answer: a
Answer: a
Answer: a
22. With the use of Jigs and fixture quality control expenses will
a) Reduce
b) Increases
c) Jigs and fixture are not used in any production process
d) None of the mentioned
Answer: a
Answer: a
24. Which of the following is not correct about fixture?
a) It is used to hold the work
b) It is used to position the work the work
c) It assures high accuracy of parts
d) It is used to guide the cutting tool
Answer: d
Answer: d
26. In which of the following operation jigs are preferred over fixture?
a) Drilling
b) Turning
c) Milling
d) Grinding
Answer: a
Answer: b
28) V-blocks (Vee locators) are used for clamping as well as locating when faces are inclined upto
a. 30°
b. 12°
c. 9°
d. 3°
Answer: a. 3°
a. machining tools
b. precision tools
c. both a. and b.
30) A device, in which a component is held and located for a specific operation and bushes are integrated that
guide the tool, is called as
a. jig
b. fixture
c. both a. and b.
a. drilling operation
b. reaming operation
c. tapping operation
d. milling operation
d. cannot say
33) Which of the following sentences are true for jigs and fixtures?
2. High speed, feed and depth of cut can be used in machining with the help of jigs and fixtures
3. Jigs and fixture cannot be used in machining of complex and heavy components
34) The device which place the workpiece in the same position, in jig and fixture, cycle after cycle is called as
a. placing device
b. fixing device
c. locating device
d. positioning device
35) Which fixtures are used for machining parts which must have machined details evenly spaced?
a. Profile fixtures
b. Duplex fixtures
c. Indexing fixtures
a. remover
b. ejector
c. escaper
d. blocker
Answer: b) ejector
A. Jig
B. Fixture
C. Gauge
D. Template
Ans – B
Ans – C
39. Which one of the following bushing is used to locate the renewable bushing
B. Liner bushing
C. Special bushing
D. Knurled bushing
Ans – B
40. Which among the following is a locate used for location from internal diameter
A. Solid support
C. Vee locator
D. Nest locator
Ans – B
41. Which one of the following jigs consists of drill plate, which rests on the component to be drilled
A. Solid jig
B. Plate jig
C. Box jig
D. Trunnion jig
Ans – B
42. Which among the following jigs is used for location from a bore
A. Plate jig
B. Solid jig
C. Post jig
D. Box jig
Ans – C
Ans – C
Ans – A
Ans – D
A. Mild steel
B. Cast iron
C. Cast steel
D. Tool steel
Ans – D
47. Which among the following locator is best suitable for location of a round shaped job
C. Vee locator
48. Which one of the following devices is used for the convenience of fabrication of a job by welding which is
set in this device so that it can be swiveled around 360° as per requirement
A. Gauge
B. Template
C. Jig
D. Fixture
Ans – D
49. Which one of the following is used to clamp the job in relation to the tool in mass production
A. Jig
B. Fixture
C. Housing
D. Gauge
Ans – B
50. Which one of the following is used to guide the tool and hold the job in mass production
A. Gauge
B. Housing
C. Jig
D. Fixture
Ans – C