Fitter Question Paper

Q 1.A finish cut is given to improve the surface finish of a rough milled work piece?
A. Decrease cutting speed, feed rate and depth of cut

B. Increase feed rate, depth of cut and reduce cutting speed
C. Increase feed rate, depth of cut and cutting speed
D. Increase cutting speed, reduce feed rate and depth of cut
Q 2. A Shaft is turned in one finish cut which one of the following parameters will directly
influence the machining time?
A. Cutting depth
B. Setting angle
C. Diameter of work piece
D. Tool travel distance
Ans: D
3.You have to file an aluminum block to a smooth finish, which one of the following cut of
file is most suitable?
A.Double cut
B.Curved cut
C.Rasp cut
D.Single cut
Ans: A
4.Counter boring is done for?

A.Deburring hole ends
B.Enlarging holes to accurate size
C.Finishing cored holes
D.Accommodating socket head screws
Ans: D
5.A point to point control system is suitable only for one of the following applications?
A.Milling profile
B.Turning
C.Drilling
D.Grinding
Ans: C
6.A steel workpiece of heigh tensile strength is to be machined with a HSS milling cutter,
which one of the following rake angles is best suited for the cutter?
A.8"
B.12"
C.20"
D.28"
Ans: A
7.By using quick return mechanism in shaping machine the cutting stroke moves slow and
return stroke fast. what is the ratio between cutting stroke and return stroke?
A.2:3
B.3:2
C.5:3
D.3:5
Ans: B
8.An irregularly shaped workpiece is turned on a lathe. which one of the following work
holding accessories is used?
A.Three jaw chuck
B.Two jaw chuck
C.Driving plate
D.Face plate
Ans: D
9.The pattern on the work surface caused by the movement of the cutting tool is called?
A.Waviness
B.Roughness
C.Surface texture
D.Lay
Ans: C
10. A product is said to have the quality when?

A.Its shape and dimensions are within the limits
B.It appears to be very good
C.It is fit for use
D.The choice of material is right
Ans: C
11.Which taper is used on spindle nose of the lathe head stock?

A.Jerno taper
B.Brown and sharp taper
C.Pin taper
D.Morse taper
Ans: D
12.A hole whose lower deviation is zero is called basic hole, which one of the following
letters indicates basic hole?
A. E
B. F
C. G
D. H
Ans: D
13.While machining cast iron coolant should be?
A.Dry air
B.Kerosence
C.Machine oil
D.soft water
Ans: A
14.The tool post of a planning machine is mounted on?

A.Apron
B.Cross rail
C.Clapper box
D.Saddle
Ans: C
15.Which one of the following equipment’s is used in the shop floor for the checking of the
form that is being turned?
A.Template
B.Snap gauge
C.Dial test indicator and slip gauges
D.Tool room microscope
Ans: B
16.Which one of the following operations can be done on slotting machine?

A.External keyway on long shaft
B.Internal grooves
C.Woodruff keyway on a shaft
D.Keyway for feather keys
Ans: C
17.What will be the result if the clearance angle in drill is increased?

A.Poor wedging action
B.Weak cutting edge
C.Rough hole surface
D.Increased point angle
Ans: B
Ans: C
18.How do you recognize a drill for soft metal?

A.By the large helix angle
B.By the small helix angle
C.By the chisel edge angle
D.By the point angle which is 90 deg
Ans: A
19.Which is the correct expression for the unit of feed rate in milling?
A. m/min
B. mm/rev
C. mm/sec
D. mm/min
Ans: A
20-The degree of closeness of the measured value of a certain quantity with its true
value is known as
a. Accuracy
b. Precision
c. Standard
d. Sensitivity
(Ans: a)

21-Error of measurement =
a. True value – Measured value
b. Precision – True value
c. Measured value – Precision
d. None of the above
(Ans: a)
22-The following is an internationally recognized and accepted unit system

a. MKS
b. FPS
c. SI
d. All of the above
(Ans: c)
23-The principle of ‘Interchangeability’ is normally employed for
a. Mass production
b. Production of identical parts
c. Parts within the prescribed limits of sizes
d. All of the above
(Ans: d)
24-_____ is equal to the differences of the two limits of size of the part
a. Tolerance
b. Low limit
c. High limit
d. Design size (Ans A)
25-The amount by which the actual size of a shaft is less than the actual size of mating
hole in an assembly
a. Clearance
b. Interference
c. Allowance
d. None of the above (Ans A)
26-The following is not used to measure angles
a. Bevel protectors
b. Calibrated levels
c. Clinometers
d. Optical flats
(Ans: d)
27. Surface plate is used to check the trueness of flat surfaces.

A. True
B False (Ans A)
28. In drilling motion of job is rotary.

a) true
b) false
View Answer
Answer: b
29 The type of file used for a wood work is

A. single-cut file
B. double cut file
C. rasp-cut file
D. any one of these

Answer: Option C
30 In arc welding, the electric arc is produced between the work and the electrode by
A. voltage
B. flow of current
C. contact resistance
D. all of these
Answer: Option C
31
The cold chisels are made by
A. drawing
B. rolling
C. piercing
D. forging
Answer: Option D
32 The instrument which has all the features of try-square, bevel protractor, rule and scriber,
is
A. outside micrometer
B. inside micrometer
C. depth gauge micrometer
D. combination set
Answer: Option D
33 Which of the following is the type of lathe machine?
a) capstan
b) turret
c) both capstan and turret
d) none of the mentioned
Answer C
34 For household wiring and small units, the following should be used for safety
measure
(A) MCB
(B) ACB
(C) OCB
(D) MCCB
Ans (a)
35 Class-A fire consists of fire due to

(A) Wood
(B) Oil
(C) Transformer
(D) Chemical
(Ans: A)
36-Water is used to extinguish

(A) Class-A fires
(B) Class-B fires
(C) Class-C fires
(D) All of the above
(Ans: A)
37-The following class of fire occur in electrical equipment

(A) Class-A fires
(B) Class-B fires
(C) Class-C fires
(D) All of the above
(Ans: C)
38-The following extinguisher is suitable for cotton or other textile fire

(A) Water
(B) Soda acid
(C) Foam
(D) Dry chemicals
(Ans: D)
39 Precision of micrometre screw gauge is
A. 0.1 cm
B. 0.01 mm
C. 0.1 mm
D. 0.01 m
Ans B
40. Precision of Vernier calipers is
A. 1 mm
B. 1 cm
C. 0.1 mm
D. 0.1 cm
41. SI unit' stands for

A. Symbolically Integrated Unit
B. Standard Integrated Unit
C. Scientific International Unit
D. Standard International Unit
Ans D

Fitter Question Paper

Uploaded by

Copyright:

Available Formats

Fitter Question Paper

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Fitter Question Paper

Uploaded by

Copyright:

Available Formats

Q 1.A finish cut is given to improve the surface finish of a rough milled work piece?

A. Decrease cutting speed, feed rate and depth of cut

4.Counter boring is done for?

10. A product is said to have the quality when?

11.Which taper is used on spindle nose of the lathe head stock?

14.The tool post of a planning machine is mounted on?

16.Which one of the following operations can be done on slotting machine?

17.What will be the result if the clearance angle in drill is increased?

18.How do you recognize a drill for soft metal?

22-The following is an internationally recognized and accepted unit system

27. Surface plate is used to check the trueness of flat surfaces.

28. In drilling motion of job is rotary.

29 The type of file used for a wood work is

B. double cut file

D. any one of these

C. depth gauge micrometer

35 Class-A fire consists of fire due to

36-Water is used to extinguish

(C) Class-C fires

(D) All of the above

37-The following class of fire occur in electrical equipment

(B) Class-B fires

(C) Class-C fires

(D) All of the above

38-The following extinguisher is suitable for cotton or other textile fire

(B) Soda acid

(D) Dry chemicals

39 Precision of micrometre screw gauge is

40. Precision of Vernier calipers is

41. SI unit' stands for

You might also like