Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 130 views

    Operating Instructions: Keep This Manual For Future Needs

    Uploaded by

    walk666
    The document provides operating instructions for the FINN-POWER P1 Pressure Control system. [1] The system includes a crimping machine, pressure display unit, and pressure sensor to allow joining materials based on applied force rather than diameter. [2] It describes how to set the pressure limit and use the diameter control as a backup to stop crimping. [3] Proper setup and testing is emphasized to safely crimp sensitive materials according to the adjusted pressure limit.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Operating Instructions: Keep This Manual For Future Needs

    Uploaded by

    walk666
    130 views4 pages
    The document provides operating instructions for the FINN-POWER P1 Pressure Control system. [1] The system includes a crimping machine, pressure display unit, and pressure sensor to allow joining materials based on applied force rather than diameter. [2] It describes how to set the pressure limit and use the diameter control as a backup to stop crimping. [3] Proper setup and testing is emphasized to safely crimp sensitive materials according to the adjusted pressure limit.

    Original Title

    P1压力控制型-P1_pressure

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides operating instructions for the FINN-POWER P1 Pressure Control system. [1] The system includes a crimping machine, pressure display unit, and pressure sensor to allow joining materials based on applied force rather than diameter. [2] It describes how to set the pressure limit and use the diameter control as a backup to stop crimping. [3] Proper setup and testing is emphasized to safely crimp sensitive materials according to the adjusted pressure limit.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    130 views4 pages

    Operating Instructions: Keep This Manual For Future Needs

    Uploaded by

    walk666
    The document provides operating instructions for the FINN-POWER P1 Pressure Control system. [1] The system includes a crimping machine, pressure display unit, and pressure sensor to allow joining materials based on applied force rather than diameter. [2] It describes how to set the pressure limit and use the diameter control as a backup to stop crimping. [3] Proper setup and testing is emphasized to safely crimp sensitive materials according to the adjusted pressure limit.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    OPERATING

    INSTRUCTIONS

    FINN-POWER
    P1 Pressure Control

    RELEASED 08/02

    Lillbacka Powerco Oy
    P.O.B. 1
    FIN-62301 Härmä, Finland
    tel. + 358 6 485 4444 Keep this manual for future needs
    fax + 358 6 485 4400
    CONTENTS
    CONTENTS ........................................................................................................................... 2

    GENERAL ............................................................................................................................. 3

    MAIN PRINCIPLES OF THE OPERATION............................................................................ 3


    WARNING ........................................................................................................................................... 3
    SETTING THE PRESSURE LIMIT...................................................................................................... 4
    SETTING THE RIGHT BACKUP VALUE FOR CRIMPING DIAMETER............................................. 4

    2
    GENERAL
    Pressure control system P1 for FINN-POWER crimping machine is an ideal solution when
    joining is done according to force instead of traditional crimping based on diameter.

    Pressure control can be used when objects have too big variations in dimensions or when
    joining sensitive materials.

    FINN-POWER crimping machine with pressure control system P1 includes a crimping machine
    with VS-control, a pressure display unit and a pressure sensor.

    MAIN PRINCIPLES OF THE OPERATION


    The pressure sensor measures hydraulic pressure that has straight relation to the crimping
    force. The measured value is transformed continuously to the pressure display unit where the
    operator can see momentary value of the pressure (bar). The pressure display will also show
    the adjusted pressure limit where crimping movement will be stopped to (see instructions
    below).

    When the pressure display unit notices that the adjusted pressure has been reached it will
    send a signal to the VS-control, which stops the crimping (see the VS-control instructions for
    control options).

    The machine stops either according to signal coming from pressure display unit or according to
    the set crimping diameter in VS-control depending on which one is achieved first. This makes it
    possible to use the diameter control as a backup during the pressure crimping. This way the
    possible danger situations can be avoided if e.g. mistakes are made when setting the pressure
    limit.

    It is important to notice that crimping machines equipped with double pump system (FP20,
    FP120, FP140, FP160, FP165 and FP170) has a quite high approaching speed.
    During crimping the pressure will rise very fast if the crimping speed is high. This might cause
    overshoot of the adjusted pressure.

    Crimping machine equipped with double pump will change to the slower crimping speed either
    when 100 bar pressure level has been reached or in VS-control 2 mm before the adjusted
    crimping diameter value. To avoid or minimize pressure overshoot with objects which require
    max. 100 bar pressure, make sure that the diameter setting in VS-control is close enough to
    the real diameter value so the slow down will take place.

    WARNING
    When joining sensitive materials the object may brake and come out of the machine. Make the
    first crimp very carefully and protect yourself!
    It is important to follow these instructions. See also the operating instructions for the crimping
    machine, especially “Warnings”.

    3
    SETTING THE PRESSURE LIMIT
    1. Start the machine (see the operating instructions).
    2. The pressure display starts to blink “8 8 8 8”.
    3. After 2 seconds the display shows momentary value of pressure. Normally the pressure is
    between 1…3 bars when machine is idle.
    4. Press the “F-button” in the right lower corner of the pressure display unit and the display
    shows the set pressure limit value in channel 1 by blinking “1” (showing the channel
    number) and some numbers (showing the adjusted pressure limit value in bars).
    5. Increase the set pressure limit value by pressing “∆-button” or decrease the value by
    pressing “∇-button” until the right value blinks on the display.
    6. Press two times “F-button” or wait 15 seconds without pressing any button to return to the
    momentary value display.
    7. Check that VS-control has the pressure option on and it is ready for use. (see operating
    instructions.)
    8. When adjusted pressure limit has been reached the pressure display unit will send a signal
    to VS-control and the led light (under OUT1) will turn on.

    Shows the adjusted pressure limit.

    Press this button to increase


    the pressure limit.

    Press this button to decrease


    the pressure limit.

    After pressing this button


    the pressure limit can be set.

    After the adjusted pressure limit has


    been reached the led light will turn on. P1_kuvatekstit.eps
    P1_kuvatekstit.eps

    SETTING THE RIGHT BACKUP VALUE FOR CRIMPING


    DIAMETER
    To find the right backup crimping diameter value in VS-control:
    1. For the first test crimp set the crimping diameter to the nominal value of die set and the
    correction value to –1.00 (see operation instructions for VS-control). This way it is made
    sure that stopping will happen according to pressure.
    2. Set the right pressure limit (see instructions below). If the set values are not correct the
    object may brake and come out of the machine.
    3. Make the first test crimp carefully.
    4. Check and measure the diameter of the crimped object.
    5. When crimping for production, set the crimping diameter according to the measured
    diameter. Also consider tolerances of the object and possible bounce back of the object.

    FOR FURTHER INFORMATION SEE INSTRUCTIONS FOR THE DISPLAY UNIT


    DELIVERED TOGETHER WITH THE MACHINE.

    You might also like