2.13 CFD-BS-8110-97 PDF

Concrete Frame Design Manual
BS 8110-1997
Concrete Frame
Design Manual
British Standard for

Structural Use of Concrete
BS 8110-1997
For SAP2000®
ISO SAP113017M28 Rev. 0 November 2017

Proudly developed in the United States of America
COPYRIGHT
Copyright  Computers and Structures, Inc., 1978-2017

All rights reserved.
The CSI Logo®, SAP2000® and ETABS® are registered trademarks of Computers and
Structures, Inc. Watch & LearnTM is a trademark of Computers and Structures, Inc.
The computer programs SAP2000® and ETABS® and all associated documentation are
proprietary and copyrighted products. Worldwide rights of ownership rest with Computers
and Structures, Inc. Unlicensed use of these programs or reproduction of documentation in
any form, without prior written authorization from Computers and Structures, Inc., is ex-
plicitly prohibited.
No part of this publication may be reproduced or distributed in any form or by any means,
or stored in a database or retrieval system, without the prior explicit written permission of
the publisher.
Further information and copies of this documentation may be obtained from:
Computers and Structures, Inc.

www.csiamerica.com
info@csiamerica.com (for general information)

support@csiamerica.com (for technical support questions)
DISCLAIMER
CONSIDERABLE TIME, EFFORT AND EXPENSE HAVE GONE INTO THE

DEVELOPMENT AND TESTING OF THIS SOFTWARE. HOWEVER, THE USER
ACCEPTS AND UNDERSTANDS THAT NO WARRANTY IS EXPRESSED OR
IMPLIED BY THE DEVELOPERS OR THE DISTRIBUTORS ON THE ACCURACY
OR THE RELIABILITY OF THIS PRODUCT.
THIS PRODUCT IS A PRACTICAL AND POWERFUL TOOL FOR STRUCTURAL

DESIGN. HOWEVER, THE USER MUST EXPLICITLY UNDERSTAND THE BASIC
ASSUMPTIONS OF THE SOFTWARE MODELING, ANALYSIS, AND DESIGN
ALGORITHMS AND COMPENSATE FOR THE ASPECTS THAT ARE NOT
ADDRESSED.
THE INFORMATION PRODUCED BY THE SOFTWARE MUST BE CHECKED BY A

QUALIFIED AND EXPERIENCED ENGINEER. THE ENGINEER MUST
INDEPENDENTLY VERIFY THE RESULTS AND TAKE PROFESSIONAL
RESPONSIBILITY FOR THE INFORMATION THAT IS USED.
Contents
Chapter 1 Introduction
1.1 Organization 1-2
1.2 Recommended Reading/Practice 1-3
Chapter 2 Design Prerequisites
2.1 Design Load Combinations 2-1
2.2 Design and Check Stations 2-3
2.3 Identifying Beams and Columns 2-3
2.4 Design of Beams 2-3
2.5 Design of Columns 2-4
2.6 P-Delta Effects 2-5
2.7 Element Unsupported Length 2-6
2.8 Choice of Input Units 2-6
i
Chapter 3 Design Process
3.1 Notation 3-1
3.2 Design Load Combinations 3-4
3.3 Design Strength 3-5
3.4 Column Design 3-5

3.4.1 Generation of Biaxial Interaction Surface 3-6
3.4.2 Check Column Capacity 3-9
3.4.3 Design Column Shear Reinforcement 3-13
3.5 Beam Design 3-15

3.5.1 Design Beam Flexural Reinforcement 3-16
3.5.2 Design Beam Shear Reinforcement 3-24
Appendix A Second Order P-Delta Effects
Appendix B Member Unsupported Lengths and Computation of

K-Factors
References
ii
Chapter 1
Introduction
The design of concrete frames is seamlessly integrated within the program.

Initiation of the design process, along with control of various design parameters,
is accomplished using the Design menu.
Automated design at the object level is available for any one of a number of
user-selected design codes, as long as the structures have first been modeled and
analyzed by the program. Model and analysis data, such as material properties
and member forces, are recovered directly from the model database, and no
additional user input is required if the design defaults are acceptable.
The design is based on a set of user-specified loading combinations. However,

the program provides default load combinations for each design code supported
in the program. If the default load combinations are acceptable, no definition of
additional load combinations is required.
In the design of columns, the program calculates the required longitudinal and
shear reinforcement. However, the user may specify the longitudinal steel, in
which case a column capacity ratio is reported. The column capacity ratio gives
an indication of the stress condition with respect to the capacity of the column.
The biaxial column capacity check is based on the generation of consistent

three-dimensional interaction surfaces. It does not use any empirical
1-1
Concrete Frame Design BS 8110-1997
formulations that extrapolate uniaxial interaction curves to approximate biaxial

action.
Interaction surfaces are generated for user-specified column reinforcing

configurations. The column configurations may be rectangular, square or
circular, with similar reinforcing patterns. The calculation of moment
magnification factors, unsupported lengths and strength reduction factors is
automated in the algorithm.
Every beam member is designed for flexure, shear, and torsion at output stations
along the beam span.
All beam-column joints are investigated for existing shear conditions.
For special moment resisting frames (ductile frames), the shear design of the
columns, beams and joints is based on the probable moment capacities of the
members. Also, the program will produce ratios of the beam moment capacities
with respect to the column moment capacities, to investigate weak beam/strong
column aspects, including the effects of axial force.
Output data can be presented graphically on the model, in tables for both input
and output data, or on the calculation sheet prepared for each member. For each
presentation method, the output is in a format that allows the engineer to quickly
study the stress conditions that exist in the structure and, in the event the member
reinforcing is not adequate, aid the engineer in taking appropriate remedial
measures, including altering the design member without rerunning the entire
analysis.
1.1 Organization
This manual is designed to help the user quickly become productive with the
concrete frame design options of the British Standard for Structural Use of
Concrete BS 8110-1997, which is referred to as BS in this manual. Chapter 2
provides detailed descriptions of the Deign Prerequisites used for BS
8110-1997. Chapter 3 provides detailed descriptions of the code specific process
used for 8110-1997. Chapter 4 documents the design output produced by the
programs. The appendices provide details on certain topics referenced in this
manual.
1-2 Organization
Chapter 1 - Introduction
1.2 Recommended Reading/Practice

It is strongly recommended that you read this manual and review any applicable
“Watch & Learn” Series™ tutorials, which are found on our web site,
http://www.csiamerica.com, before attempting to design a concrete frame.
Additional information can be found in the on-line Help facility available from
within the program’s main menu.
Recommended Reading/Practice 1-3

Chapter 2
Design Prerequisites
This chapter provides an overview of the basic assumptions, design

preconditions, and some of the design parameters that affect the design of
concrete frames.
In writing this manual it has been assumed that the user has an engineering
background in the general area of structural reinforced concrete design and
familiarity with the BS 8110-1997 code.
2.1 Design Load Combinations

The design load combinations are used for determining the various
combinations of the load cases for which the structure needs to be designed/
checked. The load combination factors to be used vary with the selected design
code. The load combination factors are applied to the forces and moments
obtained from the associated load cases and are then summed to obtain the
factored design forces and moments for the load combination.
For multi-valued load combinations involving response spectrum, time history,

moving loads and multi-valued combinations (of type enveloping, square-root
of the sum of the squares or absolute) where any correspondence between
interacting quantities is lost, the program automatically produces multiple sub
combinations using maxima/minima permutations of interacting quantities.
2-1
Separate combinations with negative factors for response spectrum cases are not
required because the program automatically takes the minima to be the negative
of the maxima for response spectrum cases and the permutations described in the
preceding text generate the required sub combinations.
When a design combination involves only a single multi-valued case of time

history or moving load, further options are available. The program has an option
to request that time history combinations produce sub combinations for each
time step of the time history. Also an option is available to request that moving
load combinations produce sub combinations using maxima and minima of each
design quantity but with corresponding values of interacting quantities.
For normal loading conditions involving static dead load, live load, wind load,
and earthquake load, and/or dynamic response spectrum earthquake load, the
program has built-in default loading combinations for each design code. The
combinations are based on the code recommendations and are documented for
each code in the corresponding manuals.
For other loading conditions involving moving load, time history, pattern live
loads, separate consideration of roof live load, snow load, etc., the user must
define design loading combinations either in lieu of or in addition to the default
design loading combinations.
The default load combinations assume all load cases declared as dead load to be
additive. Similarly, all cases declared as live load are assumed additive.
However, each load case declared as wind or earthquake, or response spectrum
cases, is assumed to be non additive with each other and produces multiple
lateral load combinations. Also wind and static earthquake cases produce
separate loading combinations with the sense (positive or negative) reversed. If
these conditions are not correct, the user must provide the appropriate design
combinations.
The default load combinations are included in design if the user requests them to
be included or if no other user defined combination is available for concrete
design. If any default combination is included in design, then all default
combinations will automatically be updated by the program any time the design
code is changed or if static or response spectrum load cases are modified.
2-2 Design Load Combinations

Chapter 2 - Design Prerequisites
Live load reduction factors can be applied to the member forces of the live load
case on an element-by-element basis to reduce the contribution of the live load
to the factored loading.
The user is cautioned that if moving load or time history results are not requested
to be recovered in the analysis for some or all of the frame members, then the
effects of those loads will be assumed to be zero in any combination that
includes them.
2.2 Design and Check Stations

For each load combination, each element is designed or checked at a number of
locations along the length of the element. The locations are based on equally
spaced segments along the clear length of the element. The number of segments
in an element is requested by the user before the analysis is made. The user can
refine the design along the length of an element by requesting more segments.
2.3 Identifying Beams and Columns

In the program all beams and columns are represented as frame elements. But
design of beams and columns requires separate treatment. Identification for a
concrete element is done by specifying the frame section assigned to the element
to be of type beam or column. If any brace elements are in the frame, the brace
element also would be identified as either a beam or a column element based on
the section assigned to the brace element.
2.4 Design of Beams

In the design of concrete beams, in general, the program calculates and reports
the required areas of steel for flexure and shear based on the beam moments,
shears, load combination factors, and other criteria, which are described in detail
in the code specific manuals. The reinforcement requirements are calculated at a
user-defined number of stations along the beam span.
All of the beams are designed for major direction flexure, shear and torsion only.
Effects due to any axial forces and minor direction bending that may exist in the
beams must be investigated independently by the user.
Design and Check Stations 2-3

In designing the flexural reinforcement for the major moment at a particular

section of a particular beam, the steps involve the determination of the maximum
factored moments and the determination of the reinforcing steel. The beam
section is designed for the maximum positive and maximum negative factored
moment envelopes obtained from all of the load combinations. Negative beam
moments produce top steel. In such cases, the beam is always designed as a
rectangular section. Positive beam moments produce bottom steel. In such cases,
the beam may be designed as a rectangular or a T beam. For the design of
flexural reinforcement, the beam is first designed as a singly reinforced beam. If
the beam section is not adequate, then the required compression reinforcement is
calculated.
In designing the shear reinforcement for a particular beam for a particular set of
loading combinations at a particular station due to the beam major shear, the
steps involve the determination of the factored shear force, the determination of
the shear force that can be resisted by concrete, and the determination of the
reinforcement steel required to carry the balance.
2.5 Design of Columns

In the design of columns, the program calculates the required longitudinal steel,
or if the longitudinal steel is specified, the column stress condition is reported in
terms of a column capacity ratio, which is a factor that gives an indication of the
stress condition of the column with respect to the capacity of the column. The
design procedure for the reinforced concrete columns of the structure involves
the following steps:
 Generate axial force-biaxial moment interaction surfaces for all of the

different concrete section types of the model.
 Check the capacity of each column for the factored axial force and bending
moments obtained from each loading combination at each end of the
column. This step is also used to calculate the required reinforcement (if
none was specified) that will produce a capacity ratio of 1.0.
The generation of the interaction surface is based on the assumed strain and
stress distributions and some other simplifying assumptions. These stress and
strain distributions and the assumptions are documented in Chapter 3.
2-4 Design of Columns

Chapter 2 - Design Prerequisites
The shear reinforcement design procedure for columns is very similar to that for
beams, except that the effect of the axial force on the concrete shear capacity
needs to be considered.
For certain special seismic cases, the design of columns for shear is based on the
capacity shear. The capacity shear force in a particular direction is calculated
from the moment capacities of the column associated with the factored axial
force acting on the column. For each load combination, the factored axial load is
calculated using the load cases and the corresponding load combination factors.
Then, the moment capacity of the column in a particular direction under the
influence of the axial force is calculated using the uniaxial interaction diagram in
the corresponding direction, as documented in Chapter 3.
2.6 P-Delta Effects

The program design process require that the analysis results include the P-delta
effects. The P-delta effects are considered differently for “braced” or “nonsway”
and “unbraced” or “sway” components of moments in columns or frames. For
the braced moments in columns, the effect of P-delta is limited to “individual
member stability”. For unbraced components, “lateral drift effects” should be
considered in addition to individual member stability effect. The program
assumes that “braced” or “nonsway” moments are contributed from the “dead”
or “live” loads. Whereas, “unbraced” or “sway” moments are contributed from
all other types of loads.
For the individual member stability effects, the moments are magnified with
moment magnification factors as documented in Chapter 3 of this manual.
For lateral drift effects, the program assumes that the P-delta analysis is
performed and that the amplification is already included in the results. The
moments and forces obtained from P-delta analysis are further amplified for
individual column stability effect if required by the governing code as in the SS
CP65 codes.
The users of the program should be aware that the default analysis option in the
program is turned OFF for P-delta effect. The user can turn the P-delta analysis
ON and set the maximum number of iterations for the analysis. The default
number of iteration for P-delta analysis is 1. Further details on P-delta analysis
are provided in Appendix A of this design manual.
P-Delta Effects 2-5

2.7 Element Unsupported Lengths

To account for column slenderness effect, the column unsupported lengths are
required. The two unsupported lengths are l33 and l22. These are the lengths
between support points of the element in the corresponding directions. The
length l33 corresponds to instability about the 3-3 axis (major axis), and l22
corresponds to instability about the 2-2 axis (minor axis).
Normally, the unsupported element length is equal to the length of the element,
i.e., the distance between END-I and END-J of the element. The program,
however, allows users to assign several elements to be treated as a single
member for design. This can be done differently for major and minor bending as
documented in Appendix B of this design manual.
The user has options to specify the unsupported lengths of the elements on an
element-by-element basis.
2.8 Choice of Input Units

English as well as SI and MKS metric units can be used for input. But the codes
are based on a specific system of units. All equations and descriptions presented
subsequently correspond to that specific system of units, unless otherwise noted.
For example, the BS 8110-1997 code is published in Newton-Millimeter-
Second units. By default, all equations and descriptions presented in the chapter
“Design for BS 8110-1997” correspond to Newton-Millimeter-Second units.
However, any system of units can be used to define and design the structure in
the program.
2-6 Element Unsupported Lengths

Chapter 3
Design for BS 8110-1997
This chapter describes in detail the various aspects of the concrete design
procedure that is used by the program when the user selects the British
Standard design code BS 8110-1997 incorporating Amendments Nos. 1, 2 and
3. For simplicity, all equations and descriptions presented in this chapter
correspond to Newton-Millimeter-Second units unless otherwise noted.
3.1 Notation
The various notations used in this chapter are described herein:
Acv Area of section for shear resistance, mm2

Ag Gross area of cross-section, mm2
As Area of tension reinforcement, mm2
A's Area of compression reinforcement, mm2
Asc Total area of column longitudinal reinforcement, mm2
Asv Total cross-sectional area of links at the neutral axis, mm2
Asv / sv Area of shear reinforcement per unit length of the member,
mm2/mm
3-1
a Depth of compression block, mm

b Width or effective width of the section in the compression zone,
mm
b' Shorter section dimension, mm
bf Width or effective width of flange, mm
bw Average web width of a flanged beam, mm
C Compression force, N
d Effective depth of tension reinforcement, mm
d' Depth to center of compression reinforcement, mm
Ec Modulus of elasticity of concrete, MPa
Es Modulus of elasticity of reinforcement, assumed as 200,000 MPa
emin Minimum eccentricity, mm
fcu Characteristic cube strength at 28 days, MPa
f s' Compressive stress in a beam compression steel, MPa
fy Characteristic strength reinforcement, MPa

fyv Characteristic strength of link reinforcement, MPa (< 460 MPa)
h Overall depth of a section in the plane of bending, mm
hf Flange thickness, mm
K Normalized design moment, Mu/bd2fcu
Mu
K' Maximum for a singly reinforced concrete section, taken
bd 2 fcu
as 0.156 by assuming that moment redistribution is limited to 10%
k1 Shear strength enhancement factor for support compression
1
Concrete shear strength factor, [ f cu 25]

3
k2
le Effective height of a column, mm

lo Clear height between end restraints, mm
3-2 Notation
Chapter 3 - Design for BS 8110-1997
M Design moment at a section, N-mm

M 1, M 2 Smaller and larger end moments in slender column, N-mm
Mi Initial moment at the point of maximum additional moment,
N-mm
Mx, My Applied moments about the major and minor axes of a column,
N-mm
N Ultimate axial load, N
sv Spacing of the links along the length of the beam, mm
T Tension force, N
V Design shear force at ultimate design load, N
v Design shear stress at a beam cross-section or at a punch critical
section, MPa
vc Design ultimate shear stress resistance of a concrete beam, MPa
v'c Design concrete shear stress corrected for axial forces, MPa
vx, vy Design ultimate shear stress of a concrete section, MPa
x Neutral axis depth, mm
xbal Depth of neutral axis in a balanced section, mm
z Lever arm, mm
β Effective length factor
βb Moment redistribution factor in a member
γf Partial safety factor for load
γm Partial safety factor for material strength
εc Maximum concrete strain, 0.0035
εs Strain in tension steel
ε's Strain in compression steel
Notation 3-3
3.2 Design Load Combinations

The design loading combinations define the various factored combinations of
the load cases for which the structure is to be checked. The design loading
combinations are obtained by multiplying the characteristic loads by
appropriate partial factors of safety, γf (BS 2.4.1.3). If a structure is subjected
to dead load (DL) and live load (LL) only, the design will need only one
loading combination, namely 1.4 DL + 1.6 LL. However, in addition to the
dead load and live load, if the structure is subjected to wind (WL), and
considering that those loads are subject to reversals, the following load
combinations for ultimate limit state should be considered (BS 2.4.3):
1.4D
(BS 2.4.3)
1.4D+1.6L
1.0D ± 1.4W
1.4D ± 1.4W (BS 2.4.3)
1.2D+1.2L ± 1.2W
1.0D ± 1.4E
1.4D ± 1.4E (BS 2.4.3)
1.2D+1.2L ± 1.2W
These are the default load combinations. In addition to these load combina-
tions, the code requires that all buildings be capable of resisting a notional
design ultimate horizontal load applied at each floor or roof level. The notional
load should be equal to 0.015 times the dead load (BS 3.1.4.2). It is
recommended that the user define additional load cases to consider notional
load in the program.
Live load reduction factors, as allowed by some design codes, can be applied to
the member forces of the live load case on a member-by-member basis to
reduce the contribution of the live load to the factored loading.
3-4 Design Load Combinations

3.3 Design Strength

The design strength for concrete and steel are obtained by dividing the
characteristic strength of the material by a partial factor of safety, γm. The
values of γm used in the program are listed as follows (BS 2.4.4.1).
1.15, for reinforcement,


γ m = 1.50, for concrete in flexure and axial load, and (BS 2.4.4.1)
1.25, for shear strength without shear reinforcement.

3.4 Column Design

The user may define the geometry of the reinforcing bar configuration of each
concrete column section. If the area of reinforcing is provided by the user, the
program checks the column capacity. However, if the area of reinforcing is not
provided by the user, the program calculates the amount of reinforcing required
for the column. The design procedure for the reinforced concrete columns of
the structure involves the following steps:
 Generate axial force/biaxial moment interaction surfaces for all of the

different concrete section types of the model. A typical biaxial interaction
surface is shown in Figure 3-1. When the steel is undefined, the program
generates the interaction surfaces for the range of allowable reinforcement
from 0.4 to 6 percent (BS 3.12.5.3 and BS 3.12.6.2).
 Calculate the capacity ratio or the required reinforcing area for the factored
axial force and biaxial (or uniaxial) bending moments obtained from each
loading combination at each station of the column. The target capacity
ratio is taken as one when calculating the required reinforcing area.
 Design the column shear reinforcement.
The following three subsections describe in detail the algorithms associated

with these steps.
Design Strength 3-5

3.4.1 Generation of Biaxial Interaction Surfaces

The column capacity interaction volume is numerically described by a series of
discrete points that are generated on the three-dimensional interaction failure
surface. In addition to axial compression and biaxial bending, the formulation
allows for axial tension and biaxial bending considerations (BS 3.8.4.1). A
typical interaction diagram is shown in Figure 3-1.
Figure 3-1 A typical column interaction surface
The coordinates of these points are determined by rotating a plane of linear

strain in three dimensions on the section of the column (BS 3.4.4.4). See Figure
3-2. The linear strain diagram limits the maximum concrete strain, εc, at the
extremity of the section, to 0.0035 (BS 3.4.4.1) .
The formulation is based consistently on the basic principles of ultimate

strength design and allows for any doubly symmetric rectangular, square, or
circular column section (BS 3.8.4).
3-6 Column Design

Figure 3-2 Idealized strain distribution for generation of interaction surface
The stress in the steel is given by the product of the steel strain and the steel
modulus of elasticity, ε s Es , and is limited to the design strength of the steel,
( )
f y 1.15 . The area associated with each reinforcing bar is placed at the
actual location of the center of the bar and the algorithm does not assume any
simplifications in the manner in which the area of steel is distributed over the
cross-section of the column (such as an equivalent steel tube or cylinder). See
Figure 3-3.
Column Design 3-7

The concrete compression stress block is assumed to be rectangular, with a

stress value of 0.67 f cu γ m = 0.45 fu (BS 3.4.4.1). See Figure 3-3. The inter-
action algorithm provides corrections to account for the concrete area that is
displaced by the reinforcement in the compression zone.
0.67 f cu γ m
εc
d′ Cs1
ε1s
C a
x 2 2
ε s
C s
ε3s Ts3
ε 4s Ts4
(I) Concrete Section (II) Strain Diagram (III) Stress Diagram
Figure 3-3 Idealization of stress and strain distribution in a column section
Furthermore, it is assumed that moment redistribution in the member does not

exceed 10% (i.e., βb ≥ 0.9; BS 3.4.4.4). The code also places a limitation on the
neutral axis depth,
x
≤ 0.5 (BS 3.4.4.4)
d
to safeguard against non-ductile failures (BS 3.4.4.4). In addition, the area of

compression reinforcement is calculated assuming that the neutral axis depth
remains at the maximum permitted value.
The depth of the compression block is given by:
a = 0.9x (BS 3.4.4.4)
3-8 Column Design

3.4.2 Check Column Capacity

The column capacity is checked for each loading combination at each output
station of each column. In checking a particular column for a particular loading
combination at a particular location, the program uses the following steps:
 Determine the factored moments and forces from the load cases and the
specified load combination factors to give N , V2 , V3 , M 33 , and M 22 .
 Determine the additional moments due to slender column effect. Compute

moments due to minimum eccentricity.
 Determine total design moments by adding the corresponding additional

moments to the factored moments obtained from the analysis. Determine
whether the point, defined by the resulting axial load and biaxial moment
set, lies within the interaction volume.
The following three subsections describe in detail the algorithms associated

with these steps.
3.4.2.1 Determine Factored Moments and Forces

Each load combination is defined with a set of load factors corresponding to
the load cases. The factored loads for a particular load combination are
obtained by applying the corresponding load factors to the load cases, giving
N , V2 , V3 , M 33 , and M 22 .
3.4.2.2 Determine Additional Moments

The determination of additional moments depends on whether the frame is
“braced” or “unbraced” against sidesway (BS 3.8.1.5). For “unbraced”
columns, additional moment is automatically considered in the P-∆ analysis.
But for “braced” columns, further calculation is required for stability of
individual column members.
Column Design 3-9

3.4.2.2.1 Braced Column

The additional moment in a braced column in a particular plane is the product
of the axial load and the lateral deflection of the column in that plane (BS
3.8.3),
M add = Nau , (BS 3.8.3.1)
where, au is the deflection at the ultimate limit state, which is obtained from
au = βa Kh and (BS 3.8.3.1)
2
1  le 
βa =
2000  b 
. (BS 3.8.3.1)
In the preceding equations,
– le is the effective length in the plane under consideration. It is obtained

from
le = βl0 , (BS 3.8.1.6.1)
where β is the effective length factor, and l0 is the unsupported length

corresponding to instability in the major or minor direction of the element, l33
l22 and l33
or l22 . In calculating the value of the effective length, the β factor is

conservatively taken as 1. However, the program allows the user to overwrite
this default value.
b is the dimension of the column in the plane of bending considered.
h is also the dimension of the column in the plane of bending considered.
K is the correction factor to the deflection to take care of the influence of the
axial force, and K is conservatively taken as 1.
The program then calculates the total design moments by combining the
factored moments obtained from analysis and the additional moments. If M 1
and M 2 ( M 2 > M 1 ) are the initial end moments in a column member in a
particular plane, the maximum design moment for the column is taken as the
greatest of the following:
3 - 10 Column Design
M2 (BS 3.8.3.2)
M 1 + M add (BS 3.8.3.2)
M add
M1 + (BS 3.8.3.2)
2
N emin (BS 3.8.3.2)
where,
M i is the initial moment in a column due to design ultimate loads at the point
of maximum additional moment and is given by
M i = 0.4 M 1 + 0.6 M 2 ≥ 0.4 M 2 . (BS 3.8.3.2)
M 1 and M 2 are the smaller and the larger end moments respectively. Both
moments are assumed to be positive if the column is in single curvature. If the
column is in double curvature, M 1 is assumed to be negative.
emin is the minimum eccentricity, which is taken as 0.05 times the overall
dimension of the column in the plane of bending considered, but not more than
20 mm (BS 3.8.3.4).
h
=
emin ≤ 20 mm. (BS 3.8.3.4)
20
3.4.2.2.2 Unbraced Column

In the case of the unbraced column, it is assumed that the program analysis
includes P-delta effects so that the analysis results include the effects of the
additional moments. Therefore, no additional computation is required. That
means moment magnification factors for moments causing sidesway are taken
as unity. However, it is recommended that for P-∆ analysis, a factor be used to
obtain a P equivalent to 1.2 DL + 1.2 LL (White and Hajjar 1991).
Also, the minimum eccentricity requirements are satisfied so the design

moment should be at least
M u ≥ Nemin , (BS 3.8.3.2)
Column Design 3 - 11
where, emin is the minimum eccentricity, which is described in the previous

section. In biaxial bending, the algorithm ensures that the eccentricity exceeds
the minimum about both the axes simultaneously.
3.4.2.3 Determine Capacity Ratio

As a measure of the stress condition of the column, a capacity ratio is
calculated. The capacity ratio is basically a factor that gives an indication of
the stress condition of the column with respect to the capacity of the column.
Before entering the interaction diagram to check the column capacity, the
design forces N , M 33 , and M 22 are obtained according to the previous
subsections. The point N , M 33 , and M 22 is then placed in the interaction space
shown as point L in Figure 3-4. If the point lies within the interaction volume,
the column capacity is adequate; however, if the point lies outside the
interaction volume, the column is overstressed.
This capacity ratio is achieved by plotting the point L and determining the
location of point C. Point C is defined as the point where the line OL (if
extended outwards) will intersect the failure surface. This point is determined
by three-dimensional linear interpolation between the points that define the
failure surface. See Figure 3-4. The capacity ratio, CR, is given by the ratio
OL
.
OC
If OL = OC (or CR = 1), the point lies on the interaction surface and the
column is stressed to capacity.
If OL < OC (or CR < 1), the point lies within the interaction volume and the
column capacity is adequate.
If OL > OC (or CR > 1), the point lies outside the interaction volume and the
column is overstressed.
The maximum of all of the values of CR calculated from each load

combination is reported for each check station of the column along with the
controlling N , M 33 , and M 22 set and associated load combination number.
If the reinforcing area is not defined, the program computes the reinforcement
that will give an interaction ratio of unity.
Figure 3-4 Geometric representation of column capacity ratio
3.4.3 Design Column Shear Reinforcement

The shear reinforcement is designed for each loading combination in the major
and minor directions of the column. In designing the shear reinforcement for a
particular column for a particular loading combination due to shear forces in a
particular direction, the following steps are involved (BS 3.8.4.6):
 Calculate the design shear stress from
V
=v = , Acv bd , where (BS 3.4.5.2)
Acv
The maximum allowable shear stress, vmax is defined as:
Column Design 3 - 13
vmax = min(0.8 fcu , 5 MPa) (BS 3.4.5.12)
– If vmax exceeds the limit, the section area should be increased.
 Calculate the design concrete shear stress from (BS 3.8.4.6)
N Vd
v '=
c vc + 0.75 with (BS 3.4.5.12)
Ac M
1 1
0.79k1k2  100 As  3  400  4
vc =  
γ m  bd   d 
(BS 3.4.5.4)
where,
k1 is the enhancement factor for support compression and taken

conservatively as 1, (BS 3.4.5.8)
1
 f 3
k2 =  cu  , (BS 3.4.5.4)
 25 
γm =
1.25. (BS 2.4.4.1)
However the following limitations also apply:
100 As
0.15 ≤ ≤ 3, (BS 3.4.5.4)
bd
Vd
≤ 1, (BS 3.4.5.12)
M
4
 400 
  ≥ 1.00 (BS 3.4.5.4)
 d 
f cu ≤ 40 N mm2 , (BS 3.4.5.4)
As is the area of tensile steel, which is assumed to be half of total rebar.
 Calculate the design average shear stress that can be carried by minimum
transverse rebar, vr , as follows:
vr = 0.4 N mm2 (BS 3.4.5.3)
– If v ≤ vc′ + vr , provide minimum links defined by
Asv vr b
= , (BS 3.4.5.3)
sv 0.87 f yv
else if v > vc′ + vr , provide links given by
Asv ( v − vc′ ) b
= . (BS 3.4.5.3, Table 3.8)
sv 0.87 f yv
 If v > vmax, a failure condition is declared. (BS 3.4.5.2)
In the preceding expressions, a limit is imposed on the fyv as
fyv ≤ 500 MPa. (BS 3.4.5.1)
3.5 Beam Design

In the design of concrete beams, the program calculates and reports the
required areas of steel for flexure and shear based on the beam moments and
shears, load combination factors, and other criteria described herein or in the
subsections that follow. The reinforcement requirements are calculated at a
user-defined number of check stations along the beam span.
All of the beams are designed for major direction flexure and shear only.
Effects due to any axial forces, minor direction bending, and torsion that may
exist in the beams must be investigated independently by the user.
The beam design procedure involves the following steps:
 Design beam flexural reinforcement
 Design beam shear reinforcement
Beam Design 3 - 15
3.5.1 Design Beam Flexural Reinforcement

The beam top and bottom flexural steel is designed at a user-defined number of
check stations along the beam span. In designing the flexural reinforcement for
the major moment for a particular beam at a particular section, the following
steps are involved:
 Determine the maximum factored moments
 Determine the reinforcing steel
3.5.1.1 Determine Factored Moments

In the design of flexural reinforcement of concrete frame beams, the factored
moments for each load combination at a particular beam station are obtained
by factoring the corresponding moments for different load cases with the
corresponding load factors.
The beam section is then designed for the maximum positive and maximum
negative factored moments obtained from all of the load combinations at that
section.
Negative beam moments produce top steel. In such cases, the beam is always
designed as a Rectangular section. Positive beam moments produce bottom
steel. In such cases, the beam may be designed as a Rectangular section, or T
beam effects may be included.
3.5.1.2 Determine Required Flexural Reinforcement

In the flexural reinforcement design process, the program calculates both the
tension and compression reinforcement. Compression reinforcement is added
when the applied design moment exceeds the maximum moment capacity of a
singly reinforced section. The user has the option of avoiding the compression
reinforcement by increasing the effective depth, the width, or concrete grade.
The design procedure is based on the simplified rectangular stress block shown
in Figure 3-5 (BS 3.4.4.4), where εc is defined as:
εc =0.0035 (BS 2.5.3)
3 - 16 Beam Design
0.67 f cu γ m
εc
b
f s′ Cs
a
d′ x
As′
Ts Tc
As εc
(I) BEAM (II) STRAIN (III) STRESS
SECTION DIAGRAM DIAGRAM
Figure 3-5 Rectangular beam design
Furthermore, it is assumed that moment redistribution in the member does not

exceed 10% (i.e., βb ≥ 0.9; BS 3.4.4.4). The code also places a limitation on the
neutral axis depth,
x
≤ 0.5 (BS 3.4.4.4)
d
to safeguard against non-ductile failures (BS 3.4.4.4). In addition, the area of
compression reinforcement is calculated assuming that the neutral axis depth
remains at the maximum permitted value.
The depth of the compression block is given by:

a = 0.9x (BS 3.4.4.4)
The design procedure used by the program, for both rectangular and flanged
sections (L and T beams), is summarized in the subsections that follow. It is
assumed that the design ultimate axial force does not exceed 0.1fcuAg (BS
3.4.4.1); hence, all of the beams are designed for major direction flexure and
shear only.
Beam Design 3 - 17
3.5.1.2.1 Design of a Rectangular Beam

For rectangular beams, the moment capacity as a singly reinforced beam,
Msingle, is obtained first for a section. The reinforcing steel area is determined
based on whether M is greater than, less than, or equal to Msingle. Please see
Figure 3-5.
 Calculate the ultimate moment of resistance of the section as singly

reinforced.
M single = K ′f cu bd 2, where (BS 3.4.4.4)
K ' = 0.156
– If M ≤ Msingle, the area of tension reinforcement, As, is obtained from
M
As = , where (BS 3.4.4.4)
( 0.87 fy ) z
 K 
z = d 0.5 + 0.25 −  ≤ 0.95d ,
 0.9 
M
K= .
f cu bd 2
This is the top steel if the section is under negative moment and the
bottom steel if the section is under positive moment.
– If M > Msingle, the area of compression reinforcement, A 's , is given by
M − Msingle
A' s = (BS 3.4.4.4)
 0.67 fcu 
 f 's −
γ m 
( d − d ′)

where d' is the depth of the compression steel from the concrete
compression face, and
1 fy 
f ′s = 0.87 fy if d ′ ≤ 1 −  (BS 3.4.4.1)
d 2  800 
3 - 18 Beam Design
2d ′  d ′ 1 fy 
f ' s = E s ε c 1 − if > 1 −  (BS 3.4.4.4)
 d  d 2
 800 
 K ′ 
z = d 0.5 + 0.25 − . (BS 3.4.4.4)
 0.9 
This is the bottom steel if the section is under negative moment. From
equilibrium, the area of tension reinforcement is calculated as
Msingle M − Msingle
=As + (BS 3.4.4.4)
0.87 f y z 0.87 f y ( d − d ′ )
3.5.1.2.2 Design as a T Beam
Flanged Beam Under Negative Moment

The contribution of the flange to the strength of the beam is ignored. The
design procedure is therefore identical to the one used for Rectangular beams,
except that in the corresponding equations, b is replaced by bw . See Figure 3-6.
0.67 f cu γ m 0.67 f cu γ m
εc
bf hf
d′ f s′ Cs
Cf
As′
x
d
Cw
εs Ts Tw Tf
As
bw
(I) Beam Section (II) Strain Diagram (III) Stress Diagram
Figure 3-6 T beam design
Beam Design 3 - 19
Flanged Beam Under Positive Moment

With the flange in compression, the program analyzes the section by
considering alternative locations of the neutral axis. Initially, the neutral axis is
assumed to be located in the flange. Based on this assumption, the program
calculates the exact depth of the neutral axis. If the stress block does not extend
beyond the flange thickness, the section is designed as a rectangular beam of
width bf . If the stress block extends beyond the flange width, the contribution
of the web to the flexural strength of the beam is taken into account. Please see
Figure 3-6.
Assuming the neutral axis is in the flange, the normalized moment is computed
as
M
K= . (BS 3.4.4.4)
f cu b f d 2
Then the moment arm is computed as
 K 
z = d 0.5 + 0.25 −  ≤ 0.95d , (BS 3.4.4.4)
 0.9 
the depth of neutral axis is computed as
d−z
x= (BS 3.4.4.4)
0.45
the depth of compression block is given by
a = 0.9x. (BS 3.4.4.4)
 If a ≤ hf , the subsequent calculations for As are exactly the same as

previously defined for the Rectangular section design. However, in that
case, the width of the compression flange, bf , is taken as the width of the
beam, b, for analysis. Compression reinforcement is required if K > K ′ .
 If a > hf , calculation for As is performed in two parts. The first part is for
balancing the compressive force from the flange, Cf , and the second part is
for balancing the compressive force from the web, Cw , as shown in Figure
3-6.
3 - 20 Beam Design
In that case, the ultimate resistance moment of the flange is given by
M=
f
0.67
γm
( ) (
f cu b f − bw h f d − 0.5h f , )
the balance of moment taken by the web is computed as
M=
w M − M f , and
the normalized moment resisted by the web is given by
Mw
Kw = .
f cu bw d 2
 If Kw ≤ K1, the beam is designed as a singly reinforced concrete beam. The

area of steel is calculated as the sum of two parts, one to balance
compression in the flange and one to balance compression in the web.
Mf Mw
=As + , where
(
0.87 f y d − 0.5h f ) 0.87 f y z
 K 
z = d 0.5 + 0.25 − w  ≤ 0.95d .
 0.9 
 If Kw ≤ K', compression reinforcement is required and is calculated as

follows:
The ultimate moment of resistance of the web only is given by
M uw = K ′f cu bw d 2 .
The compression reinforcement is required to resist a moment of

magnitude
M w − M uw .
The compression reinforcement is computed as
Beam Design 3 - 21
M w − Muw
A′s =
 0.67 fcu 
 f ′s −
γ m 
( d − d' )

where,
d' is the depth of the compression steel from the concrete

compression face, and
1 fy 
f ' s = 0.87 f y if d ′ ≤ 1 −  (BS 3.4.4.4)
d 2  800 
 2d '  1 fy 
f ' s = E s ε c 1 − if d ′ > 1 −  (BS 3.4.4.4)
 d  d 2  800 
The area of tension reinforcement is obtained from equilibrium
1  Mf M M − M uw 
=As  + uw + w  , where
0.87 f y  d − 0.5h f z d − d ′ 
 k ′ 
z = d 0.5 + 0.25 +  ≤ 0.95d .
 0.9 
3.5.1.3 Minimum and Maximum Tensile Reinforcement

The minimum flexural tensile steel required for a beam section is given by the
following table, which is taken from BS Table 3.25 (BS 3.12.5.3), with
interpolation for reinforcement of intermediate strength:
Minimum percentage
Definition of
Section Situation percentage fy = 250 MPa fy = 460 MPa
As
Rectangular  100 0.24 0.13
bh
3 - 22 Beam Design
Minimum percentage
Definition of
Section Situation percentage fy = 250 MPa fy = 460 MPa
bw As
< 0.4 100 0.32 0.18
bf bw h
T or L beam with
web in tension
bw As
≥ 0.4 100 0.24 0.13
bf bw h
T beam with web As

 100 0.48 0.26
in compression bw h
L beam with web As

 100 0.36 0.20
in compression bw h
The minimum flexural compression steel, if it is required at all, provided in a

rectangular beam or T beam section is given by the following table, which is
taken from BS Table 3.25 (BS 3.12.5.3), with interpolation for reinforcement of
intermediate strength:
Definition of Minimum
Section Situation percentage percentage
As′
Rectangular  100 0.20
bh
As′
Web in tension 100 0.40
bf hf
T beam
As′
Web in compression 100 0.20
bw h
In addition, an upper limit on both the tension reinforcement and compression

reinforcement has been imposed to be 0.04 times the gross cross-sectional area
(BS 3.12.6.1).
Beam Design 3 - 23
3.5.2 Design Beam Shear Reinforcement

The shear reinforcement is designed for each loading combination in the major
and minor directions of the column. In designing the shear reinforcement for a
particular beam for a particular loading combination due to shear forces in a
particular direction, the following steps are involved (BS 3.4.5):
 Calculate the design shear stress as
V
=v = , Acv bd , where (BS 3.4.5.2)
Acv
the maximum allowable shear stress, vmax is defined as:
vmax = min(0.8 fcu , 5 MPa) (BS 3.4.5.2)
– If v exceeds the limits, the section area should be increased.
 Calculate the design concrete shear stress from

1 1
0.79k1k2  100 As  3  400  4
vc =
γ m  bd   d 
, (BS 3.4.5.2)
where,
k1 is the enhancement factor for support compression,
and k1 is conservatively taken as 1, (BS 3.4.5.8)
1 1
 f  3  80  3
k2 =  cu  , and 1 ≤ k2 ≤   (BS 3.4.5.4)
 30   30 
γ m = 1.25. (BS 2.4.4.1)
However, the following limitations also apply:
100 As
0.15 ≤ ≤ 3, (BS 3.4.5.4)
bd
3 - 24 Beam Design
1
 400  4
  ≥1 (BS 3.4.5.4)
 d 
fcu ≤ 40 MPa (for calculation purpose only) (BS 3.4.5.4)
As is the area of tension reinforcement.
 Calculate the design average shear stress that can be carried by minimum
transverse rebar, vr , as follows:
=
vr 0.4 + vc (BS 3.4.5.3)
As is the area of tensile steel.
– If v ≤ vc + vr , provide minimum links defined by
As vr b
= , (BS 3.4.5.3)
sv 0.87 f yv
else if v > vc + vr , provide links given by
Asv ( v − vc ) b
= . (BS 3.4.5.3)
sv 0.87 f yv
In the preceding expressions, a limit is imposed on the fyv as
fyv ≤ 500 MPa (BS 3.4.5.1)
The maximum of all of the calculated Asv /sv values, obtained from each load
combination, is reported along with the controlling shear force and associated
load combination.
The beam shear reinforcement requirements considered by the program are

based purely on shear strength considerations. Any minimum stirrup
requirements to satisfy spacing and volumetric considerations must be
investigated independently of the program by the user.
Beam Design 3 - 25
APPENDICES
Appendix A
Second Order P-Delta Effects
Typically, design codes require that second order P-delta effects be considered
when designing concrete frames. They are the global lateral translation of the
frame and the local deformation of members within the frame.
Consider the frame object shown in Figure A-1, which is extracted from a story
level of a larger structure. The overall global translation of this frame object is
indicated by ∆. The local deformation of the member is shown as δ. The total
second order P-delta effects on this frame object are those caused by both ∆ and
δ.
The program has an option to consider P-delta effects in the analysis. When
P-delta effects are considered in the analysis, the program does a good job of
capturing the effect due to the ∆ deformation shown in Figure A-1, but it does
not typically capture the effect of the δ deformation (unless, in the model, the
frame object is broken into multiple elements over its length).
A-1
Figure A-1 The Total Second Order P-Delta Effects on a

Frame Element Caused by Both ∆ and δ
Consideration of the second order P-delta effects is generally achieved by
computing the flexural design capacity using a formula similar to that shown in
the following equation.
MCAP = aMnt + bMlt where,
MCAP = Flexural design capacity required

Mnt = Required flexural capacity of the member assuming there is
no joint translation of the frame (i.e., associated with the δ
deformation in Figure A-1)
Mlt = Required flexural capacity of the member as a result of
lateral translation of the frame only (i.e., associated with the
∆ deformation in Figure A-1)
a = Unitless factor multiplying Mnt
b = Unitless factor multiplying Mlt (assumed equal to 1 by the
program; see the following text)
When the program performs concrete frame design, it assumes that the factor b
is equal to 1 and calculates the factor a. That b = 1 assumes that P-delta effects
have been considered in the analysis, as previously described. Thus, in general,
when performing concrete frame design in this program, consider P-delta
effects in the analysis before running the program.
A-2 Second Order P-Delta Effects

Appendix B
Member Unsupported Lengths and
Computation of K-Factors
The column unsupported lengths are required to account for column slenderness
effects. The program automatically determines the unsupported length ratios,
which are specified as a fraction of the frame object length. Those ratios times
the frame object length give the unbraced lengths for the members. Those ratios
can also be overwritten by the user on a member-by-member basis, if desired,
using the overwrite option.
There are two unsupported lengths to consider. They are L33 and L22, as shown in
Figure B-1. These are the lengths between support points of the member in the
corresponding directions. The length L33 corresponds to instability about the 3-3
axis (major axis), and L22 corresponds to instability about the 2-2 axis (minor
axis).
In determining the values for L22 and L33 of the members, the program
recognizes various aspects of the structure that have an effect on these lengths,
such as member connectivity, diaphragm constraints and support points. The
program automatically locates the member support points and evaluates the
corresponding unsupported length.
B-1
Figure B-1 Axis of bending and unsupported length
It is possible for the unsupported length of a frame object to be evaluated by the

program as greater than the corresponding member length. For example, assume
a column has a beam framing into it in one direction, but not the other, at a floor
level. In that case, the column is assumed to be supported in one direction only at
that story level, and its unsupported length in the other direction will exceed the
story height.
B-2 Member Unsupported Lengths and Computation of K-Factors

References
CP, 1999. CP 65:Part 1:1999, Code of Practice for Structural Use of Concrete
Part 1: Design and Construction Incorporating Erratum No. 1, September
2000, Singapore Productivity and Standards Board, Singapore.
BC, 2008. BC 2:2008, Design Guide of High Strength Concrete to Singapore

Standard CP65, February 2008, Building and Construction Authority, Sin-
gapore.
CSI, 2012a. Getting Started, Computers and Structures, Inc., Berkeley, Cali-
fornia.
CSI, 2012b. Welcome to ETABS 2013, Computers and Structures, Inc.,

Berkeley, California.
CSI, 2012c. CSI Analysis Reference Manual, Computers and Structures, Inc.,
Berkeley, California.
White, D. W. and J. F. Hajjar, 1991. “Application of Second-Order Elastic

Analysis in LRFD: Research to Practice,” Engineering Journal, American
Institute of Steel Construction, Inc., Vol. 28, No. 4, 1991.

2.13 CFD-BS-8110-97 PDF

Uploaded by

Copyright:

Available Formats

2.13 CFD-BS-8110-97 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

2.13 CFD-BS-8110-97 PDF

Uploaded by

Copyright:

Available Formats

Concrete Frame Design Manual

British Standard for

ISO SAP113017M28 Rev. 0 November 2017

Copyright  Computers and Structures, Inc., 1978-2017

Further information and copies of this documentation may be obtained from:

Computers and Structures, Inc.

info@csiamerica.com (for general information)

CONSIDERABLE TIME, EFFORT AND EXPENSE HAVE GONE INTO THE

THIS PRODUCT IS A PRACTICAL AND POWERFUL TOOL FOR STRUCTURAL

THE INFORMATION PRODUCED BY THE SOFTWARE MUST BE CHECKED BY A

1.1 Organization 1-2

1.2 Recommended Reading/Practice 1-3

Chapter 2 Design Prerequisites

2.1 Design Load Combinations 2-1

2.2 Design and Check Stations 2-3

2.3 Identifying Beams and Columns 2-3

2.4 Design of Beams 2-3

2.5 Design of Columns 2-4

2.6 P-Delta Effects 2-5

2.7 Element Unsupported Length 2-6

2.8 Choice of Input Units 2-6

3.2 Design Load Combinations 3-4

3.3 Design Strength 3-5

3.4 Column Design 3-5

3.5 Beam Design 3-15

Appendix A Second Order P-Delta Effects

Appendix B Member Unsupported Lengths and Computation of

The design of concrete frames is seamlessly integrated within the program.

The design is based on a set of user-specified loading combinations. However,

The biaxial column capacity check is based on the generation of consistent

formulations that extrapolate uniaxial interaction curves to approximate biaxial

Interaction surfaces are generated for user-specified column reinforcing

All beam-column joints are investigated for existing shear conditions.

1.2 Recommended Reading/Practice

Recommended Reading/Practice 1-3

This chapter provides an overview of the basic assumptions, design

2.1 Design Load Combinations

For multi-valued load combinations involving response spectrum, time history,

When a design combination involves only a single multi-valued case of time

2-2 Design Load Combinations

2.2 Design and Check Stations

2.3 Identifying Beams and Columns

2.4 Design of Beams

Design and Check Stations 2-3

In designing the flexural reinforcement for the major moment at a particular

2.5 Design of Columns

 Generate axial force-biaxial moment interaction surfaces for all of the

2-4 Design of Columns

2.6 P-Delta Effects

P-Delta Effects 2-5

2.7 Element Unsupported Lengths

2.8 Choice of Input Units

2-6 Element Unsupported Lengths

Acv Area of section for shear resistance, mm2

a Depth of compression block, mm

f s' Compressive stress in a beam compression steel, MPa

fy Characteristic strength reinforcement, MPa

Concrete shear strength factor, [ f cu 25]

le Effective height of a column, mm