Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 216 views

    Microcontrollers 8051 Input Output Ports

    Uploaded by

    rajesh
    The 8051 microcontroller has 4 input/output ports, each with 8 pins, allowing it to connect to 32 external pins total. Each pin can be individually configured as an input or output. Port 0 does not have built-in pull-up resistors like the other ports. When configured as an output, Port 0 pins act as open drains requiring an external pull-up resistor to output logic 1. The other ports have built-in pull-up resistors and can directly output logic 1. Current limits apply when pins are actively sourcing or sinking voltage.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Microcontrollers 8051 Input Output Ports

    Uploaded by

    rajesh
    216 views2 pages
    The 8051 microcontroller has 4 input/output ports, each with 8 pins, allowing it to connect to 32 external pins total. Each pin can be individually configured as an input or output. Port 0 does not have built-in pull-up resistors like the other ports. When configured as an output, Port 0 pins act as open drains requiring an external pull-up resistor to output logic 1. The other ports have built-in pull-up resistors and can directly output logic 1. Current limits apply when pins are actively sourcing or sinking voltage.

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The 8051 microcontroller has 4 input/output ports, each with 8 pins, allowing it to connect to 32 external pins total. Each pin can be individually configured as an input or output. Port 0 does not have built-in pull-up resistors like the other ports. When configured as an output, Port 0 pins act as open drains requiring an external pull-up resistor to output logic 1. The other ports have built-in pull-up resistors and can directly output logic 1. Current limits apply when pins are actively sourcing or sinking voltage.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    216 views2 pages

    Microcontrollers 8051 Input Output Ports

    Uploaded by

    rajesh
    The 8051 microcontroller has 4 input/output ports, each with 8 pins, allowing it to connect to 32 external pins total. Each pin can be individually configured as an input or output. Port 0 does not have built-in pull-up resistors like the other ports. When configured as an output, Port 0 pins act as open drains requiring an external pull-up resistor to output logic 1. The other ports have built-in pull-up resistors and can directly output logic 1. Current limits apply when pins are actively sourcing or sinking voltage.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 2

    Microcontrollers 8051 Input Output Ports

    Advertisements

     Previous Page
    Next Page  

    8051 microcontrollers have 4 I/O ports each of 8-bit, which can be configured as input or
    output. Hence, total 32 input/output pins allow the microcontroller to be connected with the
    peripheral devices.
     Pin configuration, i.e. the pin can be configured as 1 for input and 0 for output as per
    the logic state.
    o Input/Output (I/O) pin − All the circuits within the microcontroller must be
    connected to one of its pins except P0 port because it does not have pull-up
    resistors built-in.
    o Input pin − Logic 1 is applied to a bit of the P register. The output FE transistor
    is turned off and the other pin remains connected to the power supply voltage
    over a pull-up resistor of high resistance.
     Port 0 − The P0 (zero) port is characterized by two functions −
    o When the external memory is used then the lower address byte (addresses A0A7)
    is applied on it, else all bits of this port are configured as input/output.
    o When P0 port is configured as an output then other ports consisting of pins with
    built-in pull-up resistor connected by its end to 5V power supply, the pins of this
    port have this resistor left out.
    Input Configuration
    If any pin of this port is configured as an input, then it acts as if it “floats”, i.e. the input has
    unlimited input resistance and in-determined potential.
    Output Configuration
    When the pin is configured as an output, then it acts as an “open drain”. By applying logic 0 to a
    port bit, the appropriate pin will be connected to ground (0V), and applying logic 1, the external
    output will keep on “floating”.
    In order to apply logic 1 (5V) on this output pin, it is necessary to build an external pullup
    resistor.
    Port 1
    P1 is a true I/O port as it doesn’t have any alternative functions as in P0, but this port can be
    configured as general I/O only. It has a built-in pull-up resistor and is completely compatible
    with TTL circuits.
    Port 2
    P2 is similar to P0 when the external memory is used. Pins of this port occupy addresses
    intended for the external memory chip. This port can be used for higher address byte with
    addresses A8-A15. When no memory is added then this port can be used as a general
    input/output port similar to Port 1.
    Port 3
    In this port, functions are similar to other ports except that the logic 1 must be applied to
    appropriate bit of the P3 register.

    Pins Current Limitations


     When pins are configured as an output (i.e. logic 0), then the single port pins can receive
    a current of 10mA.
     When these pins are configured as inputs (i.e. logic 1), then built-in pull-up resistors
    provide very weak current, but can activate up to 4 TTL inputs of LS series.
     If all 8 bits of a port are active, then the total current must be limited to 15mA (port P0:
    26mA).
     If all ports (32 bits) are active, then the total maximum current must be limited to 71mA.
     Previous Page  Print Page

    You might also like