Technical Manual: Troubleshooting

PART NO.
TT1V1-E-01
ZAXIS200-3·225US-3·225USR-3·240-3·270-3 class
Technical Manual
Troubleshooting
HYDRAULIC EXCAVATOR
200-3 class
200-3•200LC-3•210H-3•210LCH-3•210K-3•210LCK-3•210-3•210LC-3•
210LCN-3•240N-3
225US-3 class
225US-3•225USLC-3
TECHNICAL MANUAL
225USR-3 class
225USR-3•225USRLC-3•225USRK-3•225USRLCK-3
240-3 class
240-3•240LC-3•250H-3•250LC-3•250LCN-3•250LCH-3•250K-3•250LCK-3
TROUBLESHOOTING
270-3 class
URL:http://www.hitachi-c-m.com 270-3•270LC-3•280LC-3•280LCN-3
Hydraulic Excavator
Service Manual consists of the following separate Part No;
Technical Manual (Operational Principle) : Vol. No. TO1V1-E
Technical Manual (Troubleshooting) : Vol. No. TT1V1-E
Workshop Manual : Vol. No. W1V1-E
PRINTED IN SINGAPORE (YS) 2006.07
TT1V1-E-01 Zaxis.p65 1 1/8/06, 15:31

INTRODUCTION
TO THE READER
• This manual is written for an experienced technician • If you have any questions or comments, at if you
to provide technical information needed to maintain found any errors regarding the contents of this
and repair this machine. manual, please contact using “Service Manual
Revision Request Form” at the end of this manual.
• Be sure to thoroughly read this manual for correct (Note: Do not tear off the form. Copy it for us-
product information and service procedures. age.):
Publications Marketing & Product Support
Hitachi Construction Machinery Co. Ltd.
TEL: 81-298-32-7173
FAX: 81-298-31-1162
ADDITIONAL REFERENCES
• Please refer to the materials listed below in addition • Operation Manual of the Engine
to this manual. • Parts Catalog of the Engine
• Hitachi Training Material
• The Operator’s Manual
• The Parts Catalog
MANUAL COMPOSITION
• This manual consists of three portions: the Techni- • Information included in the Technical Manual
cal Manual (Operational Principle), the Technical (Troubleshooting):
Manual (Troubleshooting) and the Workshop Man- technical information needed for operational per-
ual. formance tests, and troubleshooting procedures.
• Information included in the Technical Manual • Information included in the Workshop Manual:
(Operational Principle): technical information needed for maintenance
technical information needed for redelivery and and repair of the machine, tools and devices
delivery, operation and activation of all devices needed for maintenance and repair, maintenance
and systems. standards, and removal/installation and assem-
ble/disassemble procedures.
PAGE NUMBER
• Each page has a number, located on the center

lower part of the page, and each number contains
the following information:
Example : T 1-3-5
Consecutive Page Number for Each Group

Group Number
Section Number
T: Technical Manual W: Workshop Manual
IN-01
INTRODUCTION
SAFETY ALERT SYMBOL AND HEADLINE
NOTATIONS
In this manual, the following safety alert symbol and • CAUTION:
signal words are used to alert the reader to the Indicated potentially hazardous situation which could,
potential for personal injury of machine damage. if not avoided, result in personal injury or death.
This is the safety alert symbol. When you see this • IMPORTANT:
symbol, be alert to the potential for personal injury. Indicates a situation which, if not conformed to the
Never fail to follow the safety instructions prescribed instructions, could result in damage to the machine.
along with the safety alert symbol.
The safety alert symbol is also used to draw attention
• NOTE:
to component/part weights.
Indicates supplementary technical information or
To avoid injury and damage, be sure to use appropri-
know-how.
ate lifting techniques and equipment when lifting heavy
parts.
UNITS USED
2
• SI Units (International System of Units) are used in Example : 24.5 MPa (250 kgf/cm , 3560 psi)
this manual.
MKSA system units and English units are also A table for conversion from SI units to other system
indicated in parenthheses just behind SI units. units is shown below for reference purposees.
To Convert To Convert
Quantity Into Multiply By Quantity Into Multiply By
From From
2
Length mm in 0.03937 Pressure MPa kgf/cm 10.197
mm ft 0.003281 MPa psi 145.0
Volume L US gal 0.2642 Power kW PS 1.360
L US qt 1.057 kW HP 1.341
3 3
m yd 1.308 Temperature °C °F °C×1.8+32
Weight kg lb 2.205 Velocity km/h mph 0.6214
-1
Force N kgf 0.10197 min rpm 1.0
N lbf 0.2248 Flow rate L/min US gpm 0.2642
Torque N⋅m kgf⋅m 1.0197 mL/rev cc/rev 1.0
N⋅m lbf⋅ft 0.7375
IN-02
SAFETY
RECOGNIZE SAFETY INFORMATION
• These are the SAFETY ALERT SYMBOLS.
• When you see these symbols on your machine or

in this manual, be alert to the potential for per-
sonal injury.
• Follow recommended precautions and safe oper-
ating practices.
001-E01A-0001
SA-688
UNDERSTAND SIGNAL WORDS

• On machine safety signs, signal words designating
the degree or level of hazard - DANGER, WARNING,
or CAUTION - are used with the safety alert symbol.
• DANGER indicates an imminently hazardous

situation which, if not avoided, will result in death
or serious injury.
• WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
• CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury.
• DANGER or WARNING safety signs are located
near specific hazards. General precautions are
listed on CAUTION safety signs.
• Some safety signs don't use any of the desig-
nated signal words above after the safety alert
symbol are occasionally used on this machine.
• To avoid confusing machine protection with personal

safety messages, a signal word IMPORTANT indi-
cates a situation which, if not avoided, could result in
damage to the machine. SA-1223
• NOTE indicates an additional explanation for an

element of information.
002-E01A-1223
SA-1
SAFETY
FOLLOW SAFETY INSTRUCTIONS
• Carefully read and follow all safety signs on the
machine and all safety messages in this manual.
• Safety signs should be installed, maintained and
replaced when necessary.
• If a safety sign or this manual is damaged or

missing, order a replacement from your author-
ized dealer in the same way you order other re-
placement parts (be sure to state machine model
and serial number when ordering).
• Learn how to operate the machine and its controls
correctly and safely.
• Allow only trained, qualified, authorized personnel to
operate the machine. SA-003
• Keep your machine in proper working condition.
• Unauthorized modifications of the machine may

impair its function and/or safety and affect ma-
chine life.
• Do not modify any machine parts without au-
thorization. Failure to do so may deteriorate the
part safety, function, and/or service life. In addi-
tion, personal accident, machine trouble, and/or
damage to material caused by unauthorized
modifications will void Hitachi Warranty Policy.
• Do not use attachments and/or optional parts or
equipment not authorized by Hitachi. Failure to do
so may deteriorate the safety, function, and/or
service life of the machine. In addition, personal
accident, machine trouble, and/or damage to
material caused by using unauthorized attach-
ments and/or optional parts or equipment will void
Hitachi Warranty Policy.
• The safety messages in this SAFETY chapter are
intended to illustrate basic safety procedures of
machines. However it is impossible for these safety
messages to cover every hazardous situation you
may encounter. If you have any questions, you
should first consult your supervisor and/or your au-
thorized dealer before operating or performing
maintenance work on the machine.
003-E01B-0003
SA-2
SAFETY
PREPARE FOR EMERGENCIES
• Be prepared if a fire starts or if an accident occurs.
• Keep a first aid kit and fire extinguisher on hand.

• Thoroughly read and understand the label at-
tached on the fire extinguisher to use it properly.
• To ensure that a fire-extinguisher can be always
used when necessary, check and service the
fire-extinguisher at the recommended intervals as
specified in the fire-extinguisher manual.
• Establish emergency procedure guidelines to
cope with fires and accidents.
• Keep emergency numbers for doctors, ambu-
lance service, hospital, and fire department
posted near your telephone. SA-437
004-E01A-0437
WEAR PROTECTIVE CLOTHING

• Wear close fitting clothing and safety equipment
appropriate to the job.
You may need:

A hard hat
Safety shoes
Safety glasses, goggles, or face shield
Heavy gloves
Hearing protection
Reflective clothing
Wet weather gear
Respirator or filter mask.
Be sure to wear the correct equipment and clothing
for the job. Do not take any chances. SA-428
• Avoid wearing loose clothing, jewelry, or other

items that can catch on control levers or other
parts of the machine.
• Operating equipment safely requires the full atten-
tion of the operator. Do not wear radio or music
headphones while operating the machine.
005-E01A-0438
SA-3
SAFETY
PROTECT AGAINST NOISE
• Prolonged exposure to loud noise can cause im-
pairment or loss of hearing.
• Wear a suitable hearing protective device such as

earmuffs or earplugs to protect against objec-
tionable or uncomfortably loud noises.
006-E01A-0434
SA-434
INSPECT MACHINE
• Inspect your machine carefully each day or shift by
walking around it before you start it to avoid per-
sonal injury.
• In the walk-around inspection be sure to cover all

points described in the "RE-START INSPEC-
TION" chapter in the operator's manual.
007-E01A-0435
SA-435
SA-4
SAFETY
GENERAL PRECAUTIONS FOR CAB
• Before entering the cab, thoroughly remove all dirt
and/or oil from the soles of your work boots. If any
controls such as a pedal is operated while with
dirt and/or oil on the soles of the operator's work
boots the operator's foot may slip off the pedal,
possibly resulting in a personal accident.
• Do not leave parts and/or tools lying around the
operator's seat. Store them in their specified loca-
tions.
• Avoid storing transparent bottles in the cab. Do
not attach any transparent type window decora-
tions on the windowpanes as they may focus
sunlight, possibly starting a fire.
• Refrain from listening to the radio, or using music
headphones or mobile telephones in the cab
while operating the machine.
• Keep all flammable objects and/or explosives
away from the machine.
• After using the ashtray, always cover it to extin-
guish the match and/or tobacco.
• Do not leave cigarette lighters in the cab. When
the temperature in the cab increases, the lighter
may explode.
524-E01A-0000
SA-5
SAFETY
USE HANDHOLDS AND STEPS
• Falling is one of the major causes of personal injury.
• When you get on and off the machine, always

face the machine and maintain a three-point
contact with the steps and handrails.
• Do not use any controls as hand-holds.
• Never jump on or off the machine. Never mount or
dismount a moving machine.
• Be careful of slippery conditions on platforms,
steps, and handrails when leaving the machine.
008-E01A-0439
SA-439
ADJUST THE OPERATOR'S SEAT

• A poorly adjusted seat for either the operator or for
the work at hand may quickly fatigue the operator
leading to mis-operations.
• The seat should be adjusted whenever changing

the operator for the machine.
• The operator should be able to fully depress the
pedals and to correctly operate the control levers
with his back against the seat back.
• If not, move the seat forward or backward, and
check again.
• Adjust the rear view mirror position so that the
best rear visibility is obtained from the operator's
seat. If the mirror is broken, immediately replace it SA-462
with a new one.
009-E01A-0462
SA-6
SAFETY
ENSURE SAFETY BEFORE RISING FROM
OR LEAVING OPERATOR'S SEAT
• Before rising from the operator's seat to open/close
either side window or to adjust the seat position, be
sure to first lower the front attachment to the ground
and then move the pilot control shut-off lever to the
LOCK position. Failure to do so may allow the ma-
chine to unexpectedly move when a body part un-
intentionally comes in contact with a control lever,
possibly resulting in serious personal injury or death.
• Before leaving the machine, be sure to first lower

the front attachment to the ground and then move
the pilot control shut-off lever to the LOCK posi-
tion. Turn the key switch OFF to stop the engine.
• Before leaving the machine, close all windows,
doors, and access covers and lock them up.
FASTEN YOUR SEAT BELT

• If the machine should overturn, the operator may
become injured and/or thrown from the cab. Addi-
tionally the operator may be crushed by the over-
turning machine, resulting in serious injury or death.
• Prior to operating the machine, thoroughly ex-

amine webbing, buckle and attaching hardware. If
any item is damaged or worn, replace the seat
belt or component before operating the machine.
• Be sure to remain seated with the seat belt se-
curely fastened at all times when the machine is
in operation to minimize the chance of injury from
an accident.
・We recommend that the seat belt be replaced SA-237
every three years regardless of its apparent con-

dition.
010-E01A-0237
SA-7
SAFETY
MOVE AND OPERATE MACHINE SAFELY
• Bystanders can be run over.
• Take extra care not to run over bystanders. Con-

firm the location of bystanders before moving,
swinging, or operating the machine.
• Always keep the travel alarm and horn in working
condition (if equipped). It warns people when the
machine starts to move.
• Use a signal person when moving, swinging, or
operating the machine in congested areas. Coor-
dinate hand signals before starting the machine.
• Use appropriate illumination. Check that all lights
are operable before operating the machine. If any
faulty illumination is present, immediately repair it.
SA-426
011-E01A-0398
HANDLE STARTING AIDS SAFELY

Starting fluid:
• Starting fluid is highly flammable.
• Keep all sparks and flame away when using it.

• Keep starting fluid well away from batteries and
cables.
• Remove container from machine if engine does
not need starting fluid.
• To prevent accidental discharge when storing a
pressurized container, keep the cap on the con-
tainer, and store it in a cool, well-protected loca-
tion.
• Do not incinerate or puncture a starting fluid con-
SA-293
tainer.
036-E01A-0293-3
SA-8
SAFETY
OPERATE ONLY FROM OPERATOR'S
SEAT
• Inappropriate engine starting procedures may cause
the machine to runaway, possibly resulting in seri-
ous injury or death.
• Start the engine only when seated in the opera-

tor's seat.
• NEVER start the engine while standing on the
track or on ground.
• Do not start engine by shorting across starter
terminals.
• Before starting the engine, confirm that all control
levers are in neutral.
• Before starting the engine, confirm the safety SA-444
around the machine and sound the horn to alert

bystanders.
012-E01B-0431
JUMP STARTING
• Battery gas can explode, resulting in serious injury.
• If the engine must be jump started, be sure to

follow the instructions shown in the "OPERATING
THE ENGINE" chapter in the operator's manual.
• The operator must be in the operator's seat so
that the machine will be under control when the
engine starts. Jump starting is a two-person op-
eration.
• Never use a frozen battery.
• Failure to follow correct jump starting procedures
could result in a battery explosion or a runaway
machine.
SA-032
S013-E01A-0032
SA-9
SAFETY
KEEP RIDERS OFF MACHINE
• Riders on machine are subject to injury such as be-
ing struck by foreign objects and being thrown off
the machine.
• Only the operator should be on the machine.

Keep riders off.
• Riders also obstruct the operator's view, resulting
in the machine being operated in an unsafe
manner.
014-E01B-0427
SA-379
PRECAUTIONS FOR OPERATIONS

• Investigate the work site before starting operations.
• Be sure to wear close fitting clothing and safety

equipment appropriate for the job, such as a hard
hat, etc. when operating the machine.
• Clear all persons and obstacles from area of op-
eration and machine movement.
Always beware of the surroundings while operat-
ing. When working in a small area surrounded by
obstacles, take care not to hit the upperstructure
against obstacles.
• When loading onto trucks, bring the bucket over
the truck beds from the rear side. Take care not to
swing the bucket over the cab or over any person.
M104-05-015
SA-10
SAFETY
INVESTIGATE JOB SITE BEFOREHAND
• When working at the edge of an excavation or on a
road shoulder, the machine could tip over, possibly
resulting in serious injury or death.
• Investigate the configuration and ground condi-
tions of the job site beforehand to prevent the
machine from falling and to prevent the ground,
stockpiles, or banks from collapsing.
• Make a work plan. Use machines appropriate to
the work and job site.
• Reinforce ground, edges, and road shoulders as
necessary. Keep the machine well back from the
edges of excavations and road shoulders.
• When working on an incline or on a road shoulder, SA-380
employ a signal person as required.
• Confirm that your machine is equipped a FOPS
cab before working in areas where the possibility
of falling stones or debris exist.
• When the footing is weak, reinforce the ground
before starting work.
• When working on frozen ground, be extremely
alert. As ambient temperatures rise, footing be-
comes loose and slippery.
• Beware the possibility of fire when operating the
machine near flammable objects such as dry
grass.
• Make sure the worksite has sufficient strength to
firmly support the machine.
When working close to an excavation or at road
shoulders, operate the machine with the tracks po-
sitioned perpendicular to the cliff face with travel
motors at the rear, so that the machine can more
easily evacuate if the cliff face collapses.
• If working on the bottom of a cliff or a high bank is
required, be sure to investigate the area first and
confirm that no danger of the cliff or bank collapsing
exists. If any possibility of cliff or bank collapsing
exists, do not work on the area.
• Soft ground may collapse when operating the ma-
chine on it, possibly causing the machine to tip over.
When working on a soft ground is required, be sure
to reinforce the ground first using large pieces of
steel plates strong and firm enough to easily support
the machine.
• Note that there is always a possibility of machine
tipping over when working on rough terrain or on
slopes. Prevent machine tipping over from occurring.
When operating on rough terrain or on slopes:
• Reduce the engine speed.
• Select slow travel speed mode.
• Operate the machine slowly and be cautious with
machine movements.
SA-11
SAFETY
EQUIPMENT OF HEAD GUARD, ROPS,
FOPS
In case the machine is operated in areas where the
possibility of falling stones or debris exist, equip a
head guard, ROPS, or FOPS according to the poten-
tial hazardous conditions. (The standard cab for this
machine corresponds to ROPS and FOPS.)
ROPS: Roll-Over Protective Structure

FOPS: Falling Object Protective Structure
SA-490
PROVIDE SIGNALS FOR JOBS INVOLV-

ING MULTIPLE NUMBERS OF MACHINES
• For jobs involving multiple numbers of machines,
provide signals commonly known by all personnel
involved. Also, appoint a signal person to coordinate
the job site. Make sure that all personnel obey the
signal person's directions.
018-E01A-0481
SA-481
CONFIRM DIRECTION OF MACHINE TO

BE DRIVEN
• Incorrect travel pedal/lever operation may result in
serious injury death.
• Before driving the machine, confirm the position

of the undercarriage in relation to the operator's
position. If the travel motors are located in front of
the cab, the machine will move in reverse when
travel pedals/levers are operated to the front.
017-E01A-0491
SA-491
SA-12
SAFETY
DRIVE MACHINE SAFELY
• Before driving the machine, always confirm that the
travel levers/pedals direction corresponds to the di-
rection you wish to drive.
• Be sure to detour around any obstructions.

• Avoid traveling over obstructions. Soil, fragments
of rocks, and/or metal pieces may scatter around
the machine. Don't allow personnel to stay around
the machine while traveling.
• Driving on a slope may cause the machine to slip or

overturn, possibly resulting in serious injury or
death. SA-657
• Never attempt to ascend or descend 35 degrees

or steeper slopes.
• Be sure to fasten the seat belt.
• When driving up or down a slope, keep the bucket
facing the direction of travel, approximately 0.5 to
1.0 m (A) above the ground.
• If the machine starts to skid or becomes unstable,
immediately lower the bucket to the ground and
stop.
SA-658
SA-441
SA-442
SA-13
SAFETY
DRIVE MACHINE SAFELY
• Driving across the face of a slope or steering on a
slope may cause the machine to skid or turnover.
If the direction must be changed, move the ma-
chine to level ground, then, change the direction
to ensure safe operation.
• Avoid swinging the upperstructure on slopes.
Never attempt to swing the upperstructure down-
hill. The machine may tip over. If swinging uphill is
unavoidable, carefully operate the upperstructure
and boom at slow speed. Travel Motor
• If the engine stalls on a slope, immediately lower
the bucket to the ground. Return the control lev-
M104-05-008
ers to neutral. Then, restart the engine.
• Be sure to thoroughly warm up the machine be-
fore ascending steep slopes. If hydraulic oil has
not warmed up sufficiently, sufficient performance
may not be obtained.
• Use a signal person when moving, swinging or
operating the machine in congested areas. Coor-
dinate hand signals before starting the machine.
• Before moving machine, determine which way to
move travel pedals/levers for the direction you
Arrow-Mark
want to go. When the travel motors are in the rear,
pushing down on the front of the travel pedals or M178-03-001
pushing the levers forward moves the machine

forward, towards the idlers.
An arrow-mark seal is stuck on the inside surface
of the side frame to indicate the machine front
direction.
• Select a travel route that is as flat as possible.
Steer the machine as straight as possible, making
small gradual changes in direction.
• Before traveling on them, check the strengths of
bridges and road shoulders, and reinforce if nec-
essary.
SA-14
SAFETY
• Use wood plates in order not to damage the road
surface. Be careful of steering when operating on
asphalt roads in summer.
• When crossing train tracks, use wood plates in
order not to damage them.
• Do not make contact with electric wires or
bridges.
• When crossing a river, measure the depth of the
river using the bucket, and cross slowly. Do not
cross the river when the depth of the river is
deeper than the upper edge of the upper roller.
• When traveling on rough terrain, reduce engine
speed. Select slow travel speed. Slower speed
will reduce possible damage to the machine.
• Avoid operations that may damage the track and SA-011
undercarriage components.
• During freezing weather, always clean snow and
ice from track shoes before loading and unloading
machine, to prevent the machine from slipping.
SA-15
SAFETY
AVOID INJURY FROM ROLLAWAY ACCI-
DENTS
• Death or serious injury may result if you attempt to
mount or stop a moving machine.
To avoid rollaways:
• Select level ground when possible to park ma-
chine.
• Do not park the machine on a grade.
• Lower the bucket and/or other work tools to the
ground.
• Turn the auto-idle switch and the H/P mode
switch off.
• Run the engine at slow idle speed without load for
5 minutes to cool down the engine. SA-391
• Stop the engine and remove the key from the key
switch.
• Pull the pilot control shut-off lever to LOCK posi-
tion.
• Block both tracks and lower the bucket to the
ground. Thrust the bucket teeth into the ground if
you must park on a grade.
• Position the machine to prevent rolling.
• Park a reasonable distance from other machines.
SA-392
020-E02A-0493
SA-16
SAFETY
AVOID INJURY FROM BACK-OVER AND
SWING ACCIDENTS
• If any person is present near the machine when
backing or swinging the upperstructure, the machine
may hit or run over that person, resulting in serious
injury or death.
To avoid back-over and swing accidents:

• Always look around BEFORE YOU BACK UP
AND SWING THE MACHINE. BE SURE THAT
ALL BYSTANDERS ARE CLEAR.
• Keep the travel alarm in working condition (if
equipped).
ALWAYS BE ALERT FOR BYSTANDERS MOV-
ING INTO THE WORK AREA. USE THE HORN SA-383
OR OTHER SIGNAL TO WARN BYSTANDERS

BEFORE MOVING MACHINE.
• USE A SIGNAL PERSON WHEN BACKING UP
IF YOUR VIEW IS OBSTRUCTED. ALWAYS
KEEP THE SIGNAL PERSON IN VIEW.
Use hand signals, which conform to your local
regulations, when work conditions require a signal
person.
• No machine motions shall be made unless signals
are clearly understood by both signalman and
operator.
• Learn the meanings of all flags, signs, and mark-
ings used on the job and confirm who has the SA-384
responsibility for signaling.
• Keep windows, mirrors, and lights clean and in
good condition.
• Dust, heavy rain, fog, etc., can reduce visibility. As
visibility decreases, reduce speed and use proper
lighting.
• Read and understand all operating instructions in
the operator's manual.
021-E01A-0494
SA-17
SAFETY
KEEP PERSON CLEAR FROM WORKING
AREA
• A person may be hit severely by the swinging front
attachment or counterweight and/or may be crushed
against an other object, resulting in serious injury or
death.
• Keep all persons clear from the area of operation

and machine movement.
• Before operating the machine, set up barriers to
the sides and rear area of the bucket swing radius
to prevent anyone from entering the work area.
022-E01A-0386
SA-386
NEVER POSITION BUCKET OVER ANY-

ONE
• Never lift, move, or swing bucket above anyone or a
truck cab.
Serious injury or machine damage may result due to
bucket load spill or due to collision with the bucket.
023-E01A-0487
SA-487
AVOID UNDERCUTTING
• In order to retreat from the edge of an excavation if
the footing should collapse, always position the un-
dercarriage perpendicular to the edge of the exca-
vation with the travel motors at the rear.
• If the footing starts to collapse and if retreat is not

possible, do not panic. Often, the machine can be
secured by lowering the front attachment, in such
cases.
024-E01A-0488 SA-488
SA-18
SAFETY
AVOID TIPPING
DO NOT ATTEMPT TO JUMP CLEAR OF TIPPING
MACHINE---SERIOUS OR FATAL CRUSHING IN-
JURIES WILL RESULT
MACHINE WILL TIP OVER FASTER THAN YOU
CAN JUMP FREE
FASTEN YOUR SEAT BELT
• The danger of tipping is always present when oper-
ating on a grade, possibly resulting in serious injury
or death.
To avoid tipping:
• Be extra careful before operating on a grade.
SA-012
• Prepare machine operating area flat.

• Keep the bucket low to the ground and close to
the machine.
• Reduce operating speeds to avoid tipping or slip-
ping.
• Avoid changing direction when traveling on
grades.
• NEVER attempt to travel across a grade steeper
than 15 degrees if crossing the grade is un-
avoidable.
• Reduce swing speed as necessary when swing-
ing loads.
SA-440
• Be careful when working on frozen ground.
• Temperature increases will cause the ground to

become soft and make ground travel unstable.
025-E03B-0463
NEVER UNDERCUT A HIGH BANK

• The edges could collapse or a land slide could occur
causing serious injury or death.
026-E01A-0519
SA-489
SA-19
SAFETY
DIG WITH CAUTION
• Accidental severing of underground cables or gas
lines may cause an explosion and/or fire, possibly
resulting in serious injury or death.
• Before digging check the location of cables, gas

lines, and water lines.
• Keep the minimum distance required, by law, from
cables, gas lines, and water lines.
• If a fiber optic cable should be accidentally sev-
ered, do not look into the end. Doing so may re-
sult in serious eye injury.
• Contact your local "diggers hot line" if available in
SA-382
your area, and/or the utility companies directly.
Have them mark all underground utilities.
027-E01A-0382
OPERATE WITH CAUTION

• If the front attachment or any other part of the ma-
chine hits against an overhead obstacle, such as a
bridge, both the machine and the overhead obstacle
will be damaged, and personal injury may result as
well.
• Take care to avoid hitting overhead obstacles with

the boom or arm.
SA-389
028-E01A-0389
SA-20
SAFETY
AVOID POWER LINES
• Serious injury or death can result if the machine or
front attachments are not kept a safe distance from
electric lines.
• When operating near an electric line, NEVER

move any part of the machine or load closer than
3 m plus twice the line insulator length.
• Check and comply with any local regulations that
may apply.
• Wet ground will expand the area that could cause
any person on it to be affected by electric shock.
Keep all bystanders or co-workers away from the
site.
SA-381
029-E01A-0381
PRECAUTIONS FOR LIGHTENING

• The machine is vulnerable to lighting strikes.
• In the event of an electrical storm, immediately

stop operation, and lower the bucket to the
ground. Evacuate to a safe place far away from
the machine.
• After the electrical storm has passed, check all of
the machine safety devices for any failure. If any
failed safety devices are found, operate the ma-
chine only after repairing them.
SA-1088
OBJECT HANDLING
• If a lifted load should fall, any person nearby may be
struck by the falling load or may be crushed under-
neath it, resulting in serious injury or death.
• When using the machine for craning operations,

be sure to comply with all local regulations.
• Do not use damaged chains or frayed cables,
sables, slings, or ropes.
• Before craning, position the upperstructure with
the travel motors at the rear.
• Move the load slowly and carefully. Never move it
suddenly.
• Keep all persons well away from the load.
• Never move a load over a person's head.
• Do not allow anyone to approach the load until it
is safely and securely situated on supporting
blocks or on the ground. SA-014
• Never attach a sling or chain to the bucket teeth.

They may come off, causing the load to fall.
032-E01A-0132
SA-21
SAFETY
PROTECT AGAINST FLYING DEBRIS
• If flying debris hit eyes or any other part of the body,
serious injury may result.
• Guard against injury from flying pieces of metal or

debris; wear goggles or safety glasses.
• Keep bystanders away from the working area
before striking any object.
031-E01A-0432
SA-432
PARK MACHINE SAFELY

To avoid accidents:
• Park machine on a firm, level surface.
• Lower bucket to the ground.
• Turn auto-idle switch and H/P mode switch OFF.
• Run engine at slow idle speed without load for 5
minutes.
• Turn key switch to OFF to stop engine.
• Remove the key from the key switch.
• Pull the pilot control shut-off lever to the LOCK
position.
• Close windows, roof vent, and cab door. SA-390
• Lock all access doors and compartments.
HANDLE FLUIDS SAFELY-AVOID FIRES

• Handle fuel with care; it is highly flammable. If fuel
ignites, an explosion and/or a fire may occur, possi-
bly resulting in serious injury or death.
• Do not refuel the machine while smoking or when

near open flame or sparks.
• Always stop the engine before refueling the ma-
chine.
• Fill the fuel tank outdoors.
• All fuels, most lubricants, and some coolants are

flammable.
• Store flammable fluids well away from fire haz- SA-018
ards.
• Do not incinerate or puncture pressurized con-
tainers.
• Do not store oily rags; they can ignite and burn
spontaneously.
• Securely tighten the fuel and oil filler cap.
034-E01A-0496
SA-019
SA-22
SAFETY
TRANSPORT SAFELY
• Take care the machine may turn over when loading
or unloading the machine onto or off of a truck or
trailer.
• Observe the related regulations and rules for safe

transportation.
• Select an appropriate truck or trailer for the ma-
chine to be transported.
• Be sure to use a signal person.
• Always follow the following precautions for load-
ing or unloading:
1. Select solid and level ground.
2. Always use a ramp or deck strong enough to
support the machine weight. SA-395
3. Turn auto-idle switch OFF.

4. Always select the slow speed mode with the
travel mode switch.
5. Never load or unload the machine onto or off a
truck or trailer using the front attachment func-
tions when driving up or down the ramp.
6. Never steer the machine while on the ramp. If the
traveling direction must be changed while the
ramp, unload the machine from the ramp, repo-
sition the machine on the ground, and then try
loading again.
7. The top end of the ramp where it meets the flat-
bed is a sudden bump. Take care when traveling
over it.
8. Place blocks in front of and behind the tracks.
Securely hold the machine to the truck or trailer
deck with wire ropes.
Be sure to further follow the details described in the

TRANSPORTING section in the operator's manual.
035-E07A-0454
SA-23
SAFETY
PRACTICE SAFE MAINTENANCE
To avoid accidents:
• Understand service procedures before starting
work.
• Keep the work area clean and dry.
• Do not spray water or steam inside cab.
• Never lubricate or service the machine while it is
moving.
• Keep hands, feet and clothing away from
power-driven parts.
Before servicing the machine:

1. Park the machine on a level surface.
2. Lower the bucket to the ground.
3. Turn the auto-idle switch off.
4. Run the engine at slow idle speed without load
for 5 minutes.
5. Turn the key switch to OFF to stop engine.
SA-028
6. Relieve the pressure in the hydraulic system by
moving the control levers several times.
7. Remove the key from the switch.
8. Attach a "Do Not Operate" tag on the control
lever.
9. Pull the pilot control shut-off lever to the LOCK
position.
10. Allow the engine to cool.
500-E02C-0520
SA-527
SA-24
SAFETY
• If a maintenance procedure must be performed
with the engine running, do not leave machine
unattended.
• If the machine must be raised, maintain a 90 to
100° angle between the boom and arm. Securely
support any machine elements that must be
raised for service work.
• Inspect certain parts periodically and repair or re-
place as necessary. Refer to the section discuss-
ing that part in the "MAINTENANCE" chapter of
this manual.
•
SA-037
Keep all parts in good condition and properly in-
stalled.
• Fix damage immediately. Replace worn or broken
parts. Remove any buildup of grease, oil, or de-
bris.
• When cleaning parts, always use nonflammable
detergent oil. Never use highly flammable oil such
as fuel oil and gasoline to clean parts or surfaces.
• Disconnect battery ground cable (-) before mak-
ing adjustments to electrical systems or before
performing welding on the machine.
• Sufficiently illuminate the work site. Use a main-
tenance work light when working under or inside
the machine.
• Always use a work light protected with a guard. In
case the light bulb is broken, spilled fuel, oil, anti-
freeze fluid, or window washer fluid may catch
fire.
WARN OTHERS OF SERVICE WORK

• Unexpected machine movement can cause serious
injury.
• Before performing any work on the machine, at-

tach a "Do Not Operate" tag on the control lever.
This tag is available from your authorized dealer.
501-E01A-0287
T1J1-01-01-001
SA-25
SAFETY
SUPPORT MACHINE PROPERLY
• Never attempt to work on the machine without se-
curing the machine first.
• Always lower the attachment to the ground before

you work on the machine.
• If you must work on a lifted machine or attach-
ment, securely support the machine or attach-
ment. Do not support the machine on cinder
blocks, hollow tires, or props that may crumble
under continuous load. Do not work under a ma-
chine that is supported solely by a jack.
SA-527
519-E01A-0527
STAY CLEAR OF MOVING PARTS

• Entanglement in moving parts can cause serious
injury.
• To prevent accidents, care should be taken to

ensure that hands, feet, clothing, jewelry and hair
do not become entangled when working around
rotating parts.
502-E01A-0026
SA-026
SA-26
SAFETY
PREVENT PARTS FROM FLYING
• Grease in the track adjuster is under high pressure.
Failure to follow the precautions below may result in
serious injury, blindness, or death.
• Do not attempt to remove GREASE FITTING or

VALVE ASSEMBLY.
• As pieces may fly off, be sure to keep body and
face away from valve.
• Never attempt to disassemble the track adjuster.
Inadvertent disassembling of the track adjuster
may cause the parts such as a spring to fly off,
possibly resulting in severe personal injury or
death.
SA-344
• Travel reduction gears are under pressure.
• As pieces may fly off, be sure to keep body and

face away from AIR RELEASE PLUG to avoid
injury.
• GEAR OIL is hot. Wait for GEAR OIL to cool, and
then gradually loosen AIR RELEASE PLUG to
release pressure.
503-E01B-0344
STORE ATTACHMENTS SAFELY

• Stored attachments such as buckets, hydraulic
hammers, and blades can fall and cause serious
injury or death.
• Securely store attachments and implements to

prevent falling. Keep children and bystanders
away from storage areas.
504-E01A-0034
SA-034
SA-27
SAFETY
PREVENT BURNS
Hot spraying fluids:
• After operation, engine coolant is hot and under

pressure. Hot water or steam is contained in the
engine, radiator and heater lines.
Skin contact with escaping hot water or steam can
cause severe burns.
• To avoid possible injury from hot spraying water.

DO NOT remove the radiator cap until the engine
is cool. When opening, turn the cap slowly to the
stop. Allow all pressure to be released before
removing the cap. SA-039
• The hydraulic oil tank is pressurized. Again, be

sure to release all pressure before removing the
cap.
Hot fluids and surfaces:
• Engine oil, gear oil and hydraulic oil also become

hot during operation.
The engine, hoses, lines and other parts become
hot as well.
• Wait for the oil and components to cool before SA-225

starting any maintenance or inspection work.
505-E01B-0498
REPLACE RUBBER HOSES PERIODI-

CALLY
• Rubber hoses that contain flammable fluids under
pressure may break due to aging, fatigue, and
abrasion. It is very difficult to gauge the extent of
deterioration due to aging, fatigue, and abrasion of
rubber hoses by inspection alone.
• Periodically replace the rubber hoses. (See the

page of "Periodic replacement of parts" in the
operator's manual.)
• Failure to periodically replace rubber hoses may

cause a fire, fluid injection into skin, or the front
attachment to fall on a person nearby, which may SA-019
result in severe burns, gangrene, or otherwise

serious injury or death.
S506-E01A-0019
SA-28
SAFETY
AVOID HIGH-PRESSURE FLUIDS
• Fluids such as diesel fuel or hydraulic oil under
pressure can penetrate the skin or eyes causing se-
rious injury, blindness or death.
• Avoid this hazard by relieving pressure before

disconnecting hydraulic or other lines.
• Tighten all connections before applying pressure.
• Search for leaks with a piece of cardboard; take
care to protect hands and body from
high-pressure fluids. Wear a face shield or gog-
gles for eye protection.
• If an accident occurs, see a doctor familiar with
this type of injury immediately. Any fluid injected
into the skin must be surgically removed within a SA-031
few hours or gangrene may result.
507-E03A-0499
SA-292
SA-044
SA-29
SAFETY
PREVENT FIRES
Check for Oil Leaks:
• Fuel, hydraulic oil and lubricant leaks can lead to
fires.
• Check for oil leaks due to missing or loose clamps,
kinked hoses, lines or hoses that rub against each
other, damage to the oil-cooler, and loose
oil-cooler flange bolts.
• Tighten, repair or replace any missing, loose or
damaged clamps, lines, hoses, oil-cooler and
oil-cooler flange bolts.
• Do not bend or strike high-pressure lines.
• Never install bent or damaged lines, pipes, or
hoses.
SA-019
Check for Shorts:

• Short circuits can cause fires.
• Clean and tighten all electrical connections.
• Check before each shift or after eight(8) to ten(10)
hours operation for loose, kinked, hardened or
frayed electrical cables and wires.
• Check before each shift or after eight(8) to ten(10)
hours operation for missing or damaged terminal
caps.
• DO NOT OPERATE MACHINE if cable or wires
are loose, kinked, etc..
Clean up Flammables:
• Spilled fuel and oil, and trash, grease, debris, ac-
cumulated coal dust, and other flammables may
cause fires.
• Prevent fires by inspecting and cleaning the ma-
chine daily and by removing spilled or accumu-
lated flammables immediately.
Check Key Switch:
• If a fire breaks out, failure to stop the engine will
escalate the fire, hampering fire fighting.
Always check key switch function before operating
the machine every day:
1. Start the engine and run it at slow idle.
2. Turn the key switch to the OFF position to con-
firm that the engine stops.
• If any abnormalities are found, be sure to repair
them before operating the machine.
508-E02B-0019
Check Heat Shields:

• Damaged or missing heat shields may lead to fires.
• Damaged or missing heat shields must be re-
paired or replaced before operating the machine.
508-E02A-0393
SA-30
SAFETY
EVACUATING IN CASE OF FIRE
• If a fire breaks out, evacuate the machine in the fol-
lowing way:
• Stop the engine by turning the key switch to the

OFF position if there is time.
• Use a fire extinguisher if there is time.
• Exit the machine.
• In an emergency, if the cab door or front window
cannot be opened, break the front or rear window
panes with the emergency evacuation hammer to
escape from the cab. Refer the explanation pages SA-393
on the Emergency Evacuation Method in the op-

erator's manual.
18-E02B-0393
SS-1510
BEWARE OF EXHAUST FUMES

• Prevent asphyxiation. Engine exhaust fumes can
cause sickness or death.
• If you must operate in a building, be sure there is

adequate ventilation. Either use an exhaust pipe
extension to remove the exhaust fumes or open
doors and windows to bring enough outside air
into the area.
509-E01A-0016
SA-016
PRECAUTIONS FOR WELDING AND

GRINDING
• Welding may generate gas and/or small fires.
• Be sure to perform welding in a well ventilated

and prepared area. Store flammable objects in a
safe place before starting welding.
• Only qualified personnel should perform welding.
Never allow an unqualified person to perform
welding.
• Grinding on the machine may create fire hazards.
Store flammable objects in a safe place before
starting grinding.
• After finishing welding and grinding, recheck that
there are no abnormalities such as the area sur- SA-818
rounding the welded area still smoldering.
523-E01A-0818
SA-31
SAFETY
AVOID HEATING NEAR PRESSURIZED
FLUID LINES
• Flammable spray can be generated by heating near
pressurized fluid lines, resulting in severe burns to
yourself and bystanders.
• Do not heat by welding, soldering, or using a torch

near pressurized fluid lines or other flammable
materials.
• Pressurized lines can be accidentally cut when
heat goes beyond the immediate flame area. In-
stall temporary fire-resistant guards to protect
hoses or other materials before engaging in
welding, soldering, etc..
SA-030
AVOID APPLYING HEAT TO LINES CON-

TAINING FLAMMABLE FLUIDS
• Do not weld or flame cut pipes or tubes that contain
flammable fluids.
• Clean them thoroughly with nonflammable solvent
before welding or flame cutting them.
510-E01B-0030
REMOVE PAINT BEFORE WELDING OR

HEATING
• Hazardous fumes can be generated when paint is
heated by welding, soldering, or using a torch. If
inhaled, these fumes may cause sickness.
• Avoid potentially toxic fumes and dust.

• Do all such work outside or in a well-ventilated
area. Dispose of paint and solvent properly.
• Remove paint before welding or heating:

1. If you sand or grind paint, avoid breathing the
dust.
Wear an approved respirator. SA-029
2. If you use solvent or paint stripper, remove

stripper with soap and water before welding.
Remove solvent or paint stripper containers and
other flammable material from area. Allow fumes
to disperse at least 15 minutes before welding or
heating.
511-E01A-0029
SA-32
SAFETY
BEWARE OF ASBESTOS DUST
• Take care not to inhale dust produced in the work
site. Inhalation of asbestos fibers may be the cause
of lung cancer.
• Depending on the wok site conditions, the risk of

inhaling asbestos fiber may exist. Spray water to
prevent asbestos from becoming airborne. Don't
use compressed air.
• When operating the machine in a work site where
asbestos might be present, be sure to operate the
machine from the upwind side and wear a mask
rated to prevent the inhalation of asbestos.
• Keep bystanders out of the work site during op-
eration. SA-029
• Asbestos might be present in imitation parts. Use

only genuine Hitachi Parts.
PREVENT BATTERY EXPLOSIONS

• Battery gas can explode.
• Keep sparks, lighted matches, and flame away

from the top of battery.
• Never check battery charge by placing a metal
object across the posts. Use a voltmeter or hy-
drometer.
• Do not charge a frozen battery or start engine with
frozen battery.
There is fear of explosion. If battery electrolyte is
frozen, wait until it is liquefied completely in an
atmospheric temperature room.
• Do not continue to use or charge the battery when
electrolyte level is lower than specified. Explosion SA-032
of the battery may result.

• Loose terminals may produce sparks. Securely
tighten all terminals.
• Battery electrolyte is poisonous. If the battery should

explode, battery electrolyte may be splashed into
eyes, possibly resulting in blindness.
• Be sure to wear eye protection when checking

electrolyte specific gravity.
512-E01B-0032
SA-33
SAFETY
SERVICE AIR CONDITIONING SYSTEM
SAFELY
• If spilled onto skin, refrigerant may cause a cold
contact burn.
• Refer to the instructions described on the con-

tainer for proper use when handling the refriger-
ant.
• Use a recovery and recycling system to avoid
leaking refrigerant into the atmosphere.
• Never touch the refrigerant.
513-E01A-0405
SA-405
HANDLE CHEMICAL PRODUCTS SAFELY

• Direct exposure to hazardous chemicals can cause
serious injury. Potentially hazardous chemicals used
with your machine include such items as lubricants,
coolants, paints, and adhesives.
• A Material Safety Data Sheet (MSDS) provides

specific details on chemical products: physical
and health hazards, safety procedures, and
emergency response techniques.
• Check the MSDS before you start any job using a
hazardous chemical. That way you will know ex-
actly what the risks are and how to do the job
safely. Then follow procedures and use recom- SA-309
mended equipment.
• See your authorized dealer for MSDS's (available
only in English) on chemical products used with
your machine.
515-E01A-0309
SA-34
SAFETY
DISPOSE OF WASTE PROPERLY
• Improperly disposing of waste can threaten the en-
vironment and ecology. Potentially harmful waste
used with HITACHI equipment includes such items
as oil, fuel, coolant, brake fluid, filters, and batteries.
• Use leakproof containers when draining fluids. Do

not use food or beverage containers that may
mislead someone into drinking from them.
• Do not pour waste onto the ground, down a drain,
or into any water source.
• Air conditioning refrigerants escaping into the air
can damage the Earth's atmosphere. Govern-
ment regulations may require a certified air condi- SA-226
tioning service center to recover and recycle used

air conditioning refrigerants.
• Inquire on the proper way to recycle or dispose of
waste from your local environmental or recycling
center, or from your authorized dealer.
516-E01A-0226
BEFORE RETURNING THE MACHINE TO

THE CUSTOMER
• After maintenance or repair work is complete,
confirm that:
• The machine is functioning properly, especially

the safety systems.
• Worn or damaged parts have been repaired or
replaced
S517-E01A-0435
SA-435
SA-35
SAFETY
(Blank)
SA-36
SECTION AND GROUP SECTION 4 OPERATIONAL PER-
CONTENTS FORMANCE TEST
Group 1 Introduction
Group 2 Standard
Group 3 Engine Test
Group 4 Excavator Test
Group 5 Component Test
TECHNICAL MANUAL
SECTION 5 TROUBLESHOOTING
(Troubleshooting) Group 1 Diagnosing Procedure
Group 2 Monitor Unit
Group 3 Dr. ZX
Group 4 e-Shovel
Group 5 Component Layout
Group 6 Troubleshooting A
Group 7 Troubleshooting B
Group 8 Electrical System Inspection
TECHNICAL MANUAL (Operational Principle)
SECTION 1 GENERAL SECTION 3 COMPONENT OPERATION
Group 1 Specifications Group 1 Pump Device
Group 2 Component Layout Group 2 Swing Device
Group 3 Component Specifications Group 3 Control Valve
SECTION 2 SYSTEM Group 4 Pilot Valve
Group 1 Controller Group 5 Travel Device
Group 2 Control System Group 6 Signal Control Valve
Group 3 ECM System Group 7 Others (Upperstructure)
All information, illustrations and speci- Group 4 Hydraulic System Group 8 Others (Undercarriage)
fications in this manual are based on Group 5 Electrical System
the latest product information available
at the time of publication. The right is WORKSHOP MANUAL
reserved to make changes at any time SECTION 1 GENERAL INFORMA- Group 10 4-Spool Solenoid Valve Unit
without notice. TION Group 11 Engine
Group 1 Precautions for Disassem- SECTION 3 UNDERCARRIAGE
bling and Assembling Group 1 Swing Bearing
Group 2 Tightening Torque Group 2 Travel Device
Group 3 Painting Group 3 Center Joint
Group 4 Bleeding Air from Hydraulic Group 4 Track Adjuster
Oil Tank Group 5 Front Idler
COPYRIGHT(C)2006
SECTION 2 UPPERSTRUCTURE Group 6 Upper and Lower Roller
Hitachi Construction Machinery Co., Ltd.
Group 1 Cab Group 7 Track
Tokyo, Japan
Group 2 Counterweight SECTION 4 FRONT ATTACHMENT
All rights reserved
Group 3 Main Frame Group 1 Front Attachment
Group 4 Pump Device Group 2 Cylinder
Group 5 Control Valve Group 3 Control Valve
Group 6 Swing Device
Group 7 Pilot Valve
Group 8 Pilot Shut-Off Solenoid
Valve
Group 9 Signal Control Valve
SECTION 4
OPERATIONAL
PERFORMANCE TEST
CONTENTS
Group 1 Introduction
Operational Performance Tests ................T4-1-1 Group 3 Engine Test
Preparation for Performance Tests ...........T4-1-2 Engine Speed ...........................................T4-3-1
Engine Compression Pressure .................T4-3-3
Group 2 Standard Valve Clearance .......................................T4-3-4
ZX200-3 Class Operational Lubricant Consumption.............................T4-3-7
Performance Standard Table ..................T4-2-1
ZX225US-3 Class Operational Group 4 Excavator Test
Performance Standard Table ..................T4-2-5 Travel Speed ............................................T4-4-1
ZX225USR-3 Class Operational Track Revolution Speed............................T4-4-2
Performance Standard Table ..................T4-2-9 Mistrack Check.........................................T4-4-3
ZX240-3 Class Operational Travel Parking Leakage............................T4-4-4
Performance Standard Table ................T4-2-13 Swing Speed ............................................T4-4-5
ZX270-3 Class Operational Swing Function Drift Check ......................T4-4-6
Performance Standard Table ................T4-2-18 Swing Motor Leakage ...............................T4-4-8
Main Pump P-Q Diagram........................T4-2-24 Maximum Swingable Slant Angle ............T4-4-10
Sensor Activating Range ........................T4-2-26 Swing Bearing Play.................................T4-4-12
ZX200-3 Class DR. ZX Hydraulic Cylinder Cycle Time ................T4-4-14
Monitor Indicating Values .......................T4-2-28 Dig Function Drift Check.........................T4-4-16
ZX225US-3 Class DR. ZX Control Lever Operating Force ...............T4-4-18
Monitor Indicating Values .......................T4-2-34 Control Lever Stroke...............................T4-4-20
ZX225URS-3 Class DR. ZX Combined Operation of
Monitor Indicating Values .......................T4-2-40 Boom Raise / Swing Function Check ....T4-4-22
ZX240-3 Class DR. ZX Combined Operation of Boom Raise
Monitor Indicating Values .......................T4-2-46 / Arm Roll-In Function Check ................T4-4-24
ZX270-3 Class DR. ZX
Monitor Indicating Values .......................T4-2-52
1V1T-4-1
Group 5 Component Test
Primary Pilot Pressure..............................T4-5-1
Secondary Pilot Pressure .........................T4-5-3
Solenoid Valve Set Pressure ....................T4-5-5
Main Pump Delivery Pressure ..................T4-5-8
Main Relief Valve Set Pressure ................T4-5-9
Relief Pressure
(When relieving Swing) .....................T4-5-13
Overload Relief Valve Set Pressure ........T4-5-15
Main Pump Flow Rate Measurement ......T4-5-18
Swing Motor Drainage ............................T4-5-26
Travel Motor Drainage ............................T4-5-29
1V1T-4-2
OPERATIONAL PERFORMANCE TEST / Introduction
OPERATIONAL PERFORMANCE TESTS
Use operational performance test procedure to quan- The machine performance does not always deteriorate
titatively check all system and functions on the ma- as the working hours increase. However, the machine
chine. performance is normally considered to reduce in pro-
portion to the increase of the operation hours. Accord-
Purpose of Performance Tests ingly, restoring the machine performance by repair,
1. To comprehensively evaluate each operational adjustment, or replacement shall consider the number
function by comparing the performance test data of the machine’s working hours.
with the standard values.
2. According to the evaluation results, repair, adjust, Definition of “Performance Standard”
or replace parts or components as necessary to 1. Operation speed values and dimensions of the
restore the machine’s performance to the desired new machine.
standard. 2. Operational performance of new components
3. To economically operate the machine under op- adjusted to specifications. Allowable errors will be
timal conditions. indicated as necessary.
Kinds of Tests
1. Base machine performance test is to check the
operational performance of each system such as
engine, travel, swing, and hydraulic cylinders.
2. Hydraulic component unit test is to check the op-
erational performance of each component such
as hydraulic pump, motor, and various kinds of
valves.
Performance Standards
“Performance Standard” is shown in tables to evalu-
ate the performance test data.
Precautions for Evaluation of Test Data

1. To evaluate not only that the test data are correct,
but also in what range the test data are.
2. Be sure to evaluate the test data based on the
machine operation hours, kinds and state of work
loads, and machine maintenance conditions.
T4-1-1
OPERATIONAL PERFORMANCE TEST / Introduction
PREPARATION FOR PERFORMANCE
TESTS
Observe the following rules in order to carry out
performance tests accurately and safely.
THE MACHINE
1. Repair any defects and damage found, such as
oil or water leaks, loose bolts, cracks and so on,
before starting to test.
TEST AREA
1. Select a hard and flat surface.
2. Secure enough space to allow the machine to run
straight more than 20 m (65 ft 7 in), and to make
a full swing with the front attachment extended.
3. If required, rope off the test area and provide
signboards to keep unauthorized personnel away.
PRECAUTIONS
1. Before starting to test, agree upon the signals to
be employed for communication among cowork-
ers. Once the test is started, be sure to commu-
nicate with each other using these signals, and to
follow them without fail.
2. Operate the machine carefully and always give
first priority to safety.
3. While testing, always take care to avoid accidents
due to landslides or contact with high-voltage
power lines. Always confirm that there is sufficient
space for full swings.
4. Avoid polluting the machine and the ground with
leaking oil. Use oil pans to catch escaping oil. Pay
special attention to this when removing hydraulic T105-06-01-003
pipings.
MAKE PRECISE MEASUREMENT

1. Accurately calibrate test instruments in advance
to obtain correct data.
2. Carry out tests under the exact test conditions
prescribed for each test item.
3. Repeat the same test and confirm that the test
data obtained can be produced repeatedly. Use
mean values of measurements if necessary.
T105-06-01-004
T4-1-2
OPERATIONAL PERFORMANCE TEST / Standard
ZX200-3 CLASS OPERATIONAL
PERFORMANCE STANDARD TABLE
The standard Performance values are listed in the Engine Control Dial : Fast Idle
table below. Refer to the Group T4-3 to T4-5 for Power Mode Switch : P Mode
performance test procedures. Values indicated in Auto-Idle Switch: OFF
parentheses are reference values. Work Mode: Digging Mode
Hydraulic Oil Temperature : 50±5 °C (122±41 °F)
The following switch positions shall be selected and
the hydraulic oil temperature shall be maintained as
indicated below as the preconditions of performance
tests unless otherwise instructed in each performance
test procedure:
ZX200-3 class
Reference
PERFORMANCE TEST DESIGNATION (Performance Remarks
Page
Standard)
ENGINE SPEED min-1
T4-3-1
Lever in neutral, Value
Slow Idle Speed 800±50
indicated on Dr. ZX
Fast Idle Speed (wirh ECO deactivated) 1800±50 ↑
Lever in neutral, Pilot shut-off
Fast Idle Speed (Heater control: OFF) 1700±50 lever: UNLOCK position,
Value indicated on Dr. ZX
Pilot shut-off lever: LOCK
position, Coolant temperature:
Fast Idle Speed (Heater control: ON) 2000±50
5 °C or lower, Value indicated
on Dr. ZX
Boom raise relief operation,
Fast Idle Speed (Relief operation) 1800±50
Fast Idle Speed (E mode) 1650±50
indicated on Dr. ZX
Relief operation of boom rasie
Fast Idle Speed (HP mode) 2000±50 and arm roll-in, Value
indicated on Dr. ZX.
Auto-Idle Speed 1200±50 Value indicated on Dr. ZX.
Warming-Up Speed 1400±100 ↑
-1
ENGINE COMPRESSION PRESSURE 3.04±0.2 Engine speed: 200min T4-3-3
MPa (kgf/cm2, psi) (31±2, 442±29)
VALVE CLEARANCE (IN, EX) 0.4 With the engine cold T4-3-4
LUBRICANT CONSUMPTION Hour meter: 2000 hours or T4-3-7
30 or less
(Rated output) mL/h less
T4-2-1
ZX200-3 class
Reference
Page
Standard)
TRAVEL SPEED sec/10 m T4-4-1
Fast Speed 6.6±0.6
Slow Speed (10.2±1.0)
TRACK REVOLUTION SPEED sec/3 rev T4-4-2
Fast Speed 17.2±1.0 LC: 18.3±1.0
Slow Speed 26.7±2.0 LC: 28.4±2.0
MISTRACK mm/20 m T4-4-3
200 or less
(With fast and slow travel speed modes)
TRAVEL MOTOR LEAKAGE mm/5 min 0 T4-4-4
SWING SPEED sec/3 rev 13.5±1.0 Bucket: empty T4-4-5
SWING FUNCTION DRIFT CHECK Bucket: empty T4-4-6
1254 or less
mm /180° ZAXIS210H-3: 1368 or less
SWING MOTOR LEAKAGE mm/5 min 0 Bucket: loaded T4-4-8
MAXIMUM SWINGABLE SLANT ANGLE Bucket: loaded T4-4-10
25° or more
deg.
SWING BEARING PLAY mm 0.2 to 1.0 Allowable limit: 2.0 to 3.0 T4-4-12
HYDRAULIC CYLINDER CYCLE TIME 2.91 m arm T4-4-14
3
sec 0.8 m (PCSA heaped) bucket,
Bucket: empty
Boom Raise 3.1±0.3 ZAXIS210H-3: 3.2±0.3
Boom Lower 2.2±0.3
Arm Roll-In 3.2±0.3
Arm Roll-Out 2.5±0.3 ZAXIS210H-3: 2.6±0.3
Bucket Roll-In 3.0±0.3
Bucket Roll-Out 2.0±0.3 ZAXIS210H-3: 2.1±0.3
DIG FUNCTION DRIFT CHECK mm/5 min 2.91 m arm T4-4-16
3
0.8 m (PCSA heaped) bucket
Boom Cylinder
(Maximum Reach Position) 5 or less Bucket: loaded
(Arm Roll-In Position) 5 or less Bucket: empty
Arm Cylinder
Bucket Cylinder
Bucket Bottom
T4-2-2
ZX200-3 class
Reference
Page
Standard)
CONTROL LEVER OPERATING FORCE HITACHI lever pattern T4-4-18
N (kgf, lbf)
Boom Lever 16 (1.6, 3.6) or
less
Arm Lever 13 (1.3, 2.9) or
(ISO Lever Pattern: Swing Lever) less
Bucket Lever 13 (1.3, 2.9) or
less
Swing Lever 16 (1.6, 3.6) or
(ISO Lever Pattern: Arm Lever) less
Travel Lever 28 (2.8, 6.3) or
less
CONTROL LEVER STROKE mm HITACHI lever pattern T4-4-20
Boom Lever 97±10
Arm Lever
82±10
(ISO Lever Pattern: Swing Lever)
Bucket Lever 82±10
Swing Lever 97±10
(ISO Lever Pattern: Arm Lever)
Travel Lever 120±10
BOOM RAISE/SWING sec 2.91 m arm T4-4-22
3
3.6±0.4 0.8 m (PCSA heaped) bucket,
Bucket: empty
(Bucket Teeth Height: H) mm 6600 or more
BOOM RAISE/ARM ROLL-IN sec 2.91 m arm T4-4-24
4.3±0.5 3
HYDRAULIC SYSTEM
PRIMARY PILOT PRESSURE T4-5-1
MPa (kgf/cm2, psi)
+1.0
Engine: Fast Idle 4.0 -0.5
+10 +145
(41 -5, 582 -73)
+1.0
Engine: Slow Idle 3.8 -0.5
+10 +145
(39 -5, 552 -73)
SECONDARY PILOT PRESSURE T4-5-3
MPa (kgf/cm2, psi)
3.4 to 4.0 Value indicated on Dr. ZX
(Engine: Fast Idle (normal) and Slow Idle) (35 to 41, 494 to (Lever: Full stroke)
582)
SOLENOID VALVE SET PRESSURE Value Indicated On T4-5-5
MPa (kgf/cm2, psi) Dr. ZX±0.2 (2, 29)
+1.0
MAIN PUMP DELIVERY PRESSURE 0.7 -0.5 In neutral, Value indicated on T4-5-8
+10 +145
MPa (kgf/cm2, psi) (7.1 -5, 102 -73) Dr. ZX
T4-2-3
ZX200-3 class Reference

PERFORMANCE TEST DESIGNATION (Performance Remarks Page
Standard)
MAIN RELIEF VALVE PRESSURE T4-5-9
MPa (kgf/cm2, psi)
+2.0
Boom, Arm, Bucket (Relief operation for 34.3 -0.5 Value indicated on Dr. ZX
each) +20
(350 -5,
+291
4987 -73 )
+2.0
Power Digging 36.3 -1.0 Value indicated on Dr. ZX
+20
(370 -10,
+291
5277 -145 )
+2.3
RELIEF PRESSURE MPa (kgf/cm2, psi) 32.9 -0 Value indicated on Dr. ZX T4-5-13
(Relief operation of Swing) +23
(335 -0,
+334
4783 -0 )
OVERLOAD RELIEF PRESSURE (Reference values at 50 T4-5-15
MPa (kgf/cm2, psi) L/min)
+1.0
Boom Lower, Arm Roll-In, Bucket Roll-In 37.2 -0
+10
(379 -0,
+145
5408 -0 )
+1.0
Boom Raise, Arm Roll-Out, Bucket 39.2 -0
Roll-Out +10
(400 -0,
+145
5699 -0 )
MAIN PUMP FLOW RATE (L/min) - Refer to pages T4-2-10, 11. T4-5-18
SWING MOTOR DRAINAGE (L/min) T4-5-26
With constant speed 0.2 to 0.3
With the motor relieved (2 to 5)
TRAVEL MOTOR DRAINAGE (L/min) T4-5-29
With the track jacked up Less than 10 Allowable limit: 10
With the motor relieved Less than 15 Allowable limit: 15
T4-2-4
ZX225US-3 CLASS OPERATIONAL
test procedure:
ZX225US-3 class
Reference
Page
Standard)
ENGINE SPEED min-1
T4-3-1
indicated on Dr. ZX
on Dr. ZX
indicated on Dr. ZX
-1
MPa (kgf/cm2, psi) (31±2, 442±29)
30 or less
T4-2-5
ZX225US-3 class
Reference
Page
Standard)
Fast Speed 6.6±0.6
Fast Speed 17.2±1.0 LC: 18.3±2.0
Slow Speed 26.7±2.0 LC: 28.4±2.0
200 or less
SWING FUNCTION DRIFT CHECK T4-4-6
1263 or less Bucket: empty
mm /180°
22° or more
deg.
3
sec 0.8 m (PCSA heaped) bucket,
Bucket: empty
Boom Raise 3.1±0.3
Boom Lower 2.2±0.3
Arm Roll-Out 2.5±0.3
Bucket Roll-Out 2.0±0.3
3
Boom Cylinder
Arm Cylinder
Bucket Cylinder
Bucket Bottom
T4-2-6
ZX225US-3 class
Reference
Page
Standard)
N (kgf, lbf)
less
Arm Lever 13 (1.3, 2.9) or
less
less
Boom Lever 97±10
Arm Lever
82±10
Bucket Lever 82±10
Swing Lever 97±10
3
Bucket: empty
4.3±0.5 3
HYDRAULIC SYSTEM
MPa (kgf/cm2, psi)
+1.0
+10 +145
(41 -5, 582 -73)
+1.0
+10 +145
(39 -5, 552 -73)
MPa (kgf/cm2, psi)
582)
+1.0
+10 +145
T4-2-7
ZX225US-3 class Reference

Standard)
MPa (kgf/cm2, psi)
+2.0
each) +20
(350 -5,
+291
4987 -73 )
+2.0
+20
(370 -10,
+291
5277 -145 )
+2.3
RELIEF PRESSURE MPa (kgf/cm2, psi) 33.3 -0.5 Value indicated on Dr. ZX T4-5-13
(340 -5,
+334
4841 -73 )
+1.0
+10
(379 -0,
+145
5408 -0 )
+1.0
Roll-Out +10
(400 -0,
+145
5699 -0 )
T4-2-8
ZX225USR-3 CLASS OPERATIONAL
test procedure:
ZX225USR-3 class
Reference
Page
Standard)
ENGINE SPEED min-1
T4-3-1
indicated on Dr. ZX
position, Coolant
temperature: 5 °C or lower,
indicated on Dr. ZX
Relief operation of boom
Fast Idle Speed (HP mode) 2000±50 rasie and arm roll-in, Value
-1
MPa (kgf/cm2, psi) (31±2, 442±29)
30 or less
T4-2-9
ZX225USR-3 class
Reference
Page
Standard)
Fast Speed 6.6±0.6
Fast Speed 17.2±1.0 LC: 18.3±2.0
Slow Speed 26.7±2.0 LC: 28.4±2.0
200 or less
Bucket: empty T4-4-6
SWING FUNCTION DRIFT CHECK
1263 or less ZAXIS225USRK-3: 1377 or
mm /180°
less
25° or more
deg.
3
sec 0.8 m (PCSA heaped)
bucket, Bucket: empty
Boom Raise 3.1±0.3 ZAXIS225USRK-3: 3.2±0.3
Boom Lower 2.2±0.3
Arm Roll-Out 2.5±0.3 ZAXIS225USRK-3: 2.6±0.3
Bucket Roll-Out 2.0±0.3 ZAXIS225USRK-3: 2.1±0.3
3
0.8 m (PCSA heaped)
bucket
Boom Cylinder
Arm Cylinder
Bucket Cylinder
Bucket Bottom
T4-2-10
ZX225USR-3 class
Reference
Page
Standard)
N (kgf, lbf)
Boom Lever 16 (1.6, 3.6) or less
Arm Lever
13 (1.3, 2.9) or less
Bucket Lever 13 (1.3, 2.9) or less
Swing Lever 16 (1.6, 3.6) or less
Travel Lever 28 (2.8, 6.3) or less
Boom Lever 97±10
Arm Lever
82±10
Bucket Lever 82±10
Swing Lever 97±10
3
3.6±0.4 0.8 m (PCSA heaped)
bucket, Bucket: empty
(Bucket Teeth Height: H) mm 6700 or more ZAXIS225USRK-3: 6200 or
more
3
4.3±0.5 0.8 m (PCSA heaped)
bucket
HYDRAULIC SYSTEM
MPa (kgf/cm2, psi)
+1.0
+10 +145
(41 -5, 582 -73)
+1.0
+10 +145
(39 -5, 552 -73)
MPa (kgf/cm2, psi)
582)
+1.2
+12 +174
T4-2-11
ZX225USR-3 class Reference

Standard)
MPa (kgf/cm2, psi)
+2.0
each) +20
(350 -5,
+291
4987 -73 )
+2.0
+20
(370 -10,
+291
5277 -145 )
+2.3
(340 -5,
+334
4841 -73 )
+1.0
+10 +145
(379 -0, 5408 -0 )
+1.0
Roll-Out +10
(400 -0, 5699
+145
-0 )
T4-2-12
test procedure:
ZX240-3 class
Reference
Page
Standard)
ENGINE SPEED min-1 T4-3-1
indicated on Dr. ZX
on Dr. ZX
indicated on Dr. ZX
-1
MPa (kgf/cm2, psi) (31±2, 442±29)
30 or less
T4-2-13
ZX240-3 class
Reference
Page
Standard)
Fast Speed 6.6±0.6
Fast Speed 17.6±2.0 LC: 19.1±2.0
Slow Speed 28.6±2.0 LC: 31.0±2.0
200 or less
1565 or less
mm /180°
21.5° or more
deg.
3
(Mono Boom) 1.0 m (PCSA heaped) bucket,
sec Bucket: empty
Boom Raise 3.5±0.3
Boom Lower 2.3±0.3
3
(2-Piece Boom) 1.0 m (PCSA heaped) bucket,
sec Bucket: empty
Boom Raise 4.6±0.3
Boom Lower 3.7±0.3
Positioning Lower (without HRV) 5.9±0.3 HRV: Hose Rupture Valve
(with HRV) 6.3±0.3
Positioning Raise 4.1±0.3
T4-2-14
ZX240-3 class
Reference
Page
Standard)
DIG FUNCTION DRIFT CHECK 2.96 m arm T4-4-16
3
(Mono Boom) mm/5 min 1.0 m (PCSA heaped) bucket
Boom Cylinder
Arm Cylinder
Bucket Cylinder
Bucket Bottom
3
(2-Piece Boom) mm/5 min 1.0 m (PCSA heaped) bucket
Boom Cylinder
Arm Cylinder
Bucket Cylinder
Positioning Cylinder
Bucket Bottom
T4-2-15
ZX240-3 class
Reference
Page
Standard)
N (kgf, lbf)
less
Arm Lever 13 (1.3, 2.9) or
less
less
Boom Lever 97±10
Arm Lever
82±10
Bucket Lever 82±10
Swing Lever 97±10
3
Bucket: empty
(4.0±0.5) 3
HYDRAULIC SYSTEM
MPa (kgf/cm2, psi)
+1.0
+10 +145
(41 -5, 582 -73)
+1.0
Engine: Slow Idle 3.8 -0
+10 +145
(39 -0, 552 -0)
MPa (kgf/cm2, psi)
582)
+1.2
+12 +175
MPa (kgf/cm2, psi) (8 -5, 116 -73) Dr. ZX
T4-2-16

Standard)
MPa (kgf/cm2, psi)
+2.0
each) +20
(350 -5,
+291
4987 -73 )
+2.0
Relief operation of Positioning 35.5 -0.5 Value indicated on Dr. ZX
(2-piece boom only) +20
(362 -5,
+291
5161 -73 )
+2.0
+20
(370 -10,
+291
5277 -145 )
+2.3
(340 -5,
+334
4841 -73 )
+1.0
+10
(379 -0,
+145
5408 -0 )
+1.0
Roll-Out +10
(400 -0,
+145
5699 -0 )
T4-2-17
test procedure:
ZX270-3 class
Reference
Page
Standard)
ENGINE SPEED min-1 T4-3-1
indicated on Dr. ZX
on Dr. ZX
indicated on Dr. ZX
-1
MPa (kgf/cm2, psi) (31±2, 442±29)
25 or less
T4-2-18
ZX270-3 class
Reference
Page
Standard)
Fast Speed 6.6±0.6
Fast Speed 32.1±2.0 LC: 34.2±2.0
Slow Speed 32.1±2.0 LC: 34.2±2.0
200 or less
1610 or less
mm /180°
20° or more
deg.
3
(Mono Boom) 1.1 m (PCSA heaped) bucket,
sec Bucket: empty
Boom Raise 3.5±0.3
Boom Lower (without HRV) 2.3±0.3 HRV: Hose Rupture Valve
(with HRV) 2.5±0.3
3
(2-Piece Boom) 1.1 m (PCSA heaped) bucket,
sec Bucket: empty
Boom Raise 4.3±0.3
Boom Lower (without HRV) 3.4±0.3 HRV: Hose Rupture Valve
(with HRV) 3.7±0.3
Positioning Lower (without HRV) 5.3±0.3 HRV: Hose Rupture Valve
(with HRV) 5.7±0.3
Positioning Raise 4.0±0.3
T4-2-19
ZX270-3 class
Reference
Page
Standard)
3
(Mono Boom) mm/5 min 1.1 m (PCSA heaped) bucket
Boom Cylinder
Arm Cylinder
Bucket Cylinder
Bucket Bottom
3
(2-Piece Boom) mm/5 min 1.1 m (PCSA heaped) bucket
Boom Cylinder
Arm Cylinder
Bucket Cylinder
Positioning Cylinder
Bucket Bottom
T4-2-20
ZX270-3 class
Reference
Page
Standard)
N (kgf, lbf)
less
Arm Lever 13 (1.3, 2.9) or
less
less
Boom Lever 97±10
Arm Lever
82±10
Bucket Lever 82±10
Swing Lever 97±10
3
Bucket: empty
Bucket Teeth Height: H (Mono Boom) mm 6700 or more
(2-Piece Boom) 5800 or more
(5.5±0.5) 3
HYDRAULIC SYSTEM
MPa (kgf/cm2, psi)
+1.0
Engine: Fast Idle 4.0 -0.5 Value indicated on Dr. ZX
+10 +145
(41 -5, 582 -73)
+1.0
Engine: Slow Idle 3.8 -0 Value indicated on Dr. ZX
+10 +145
(39 -0, 552 -0)
MPa (kgf/cm2, psi)
(Engine: Fast Idle (noraml) and Slow Idle) (35 to 41, 494 to (Lever: Full stroke)
582)
+1.2
+12 +174
T4-2-21
NOTE: 1 mm=0.03937 in
Standard)
MPa (kgf/cm2, psi)
+2.0
each) +20
(350 -5,
+291
4987 -73 )
+2.0
Relief operation of Positioning 35.5 -0.5 Value indicated on Dr. ZX
(2-piece boom only) +20
(362 -5,
+291
5161 -73 )
+2.0
+20
(370 -10,
+291
5277 -145 )
+2.3
(340 -5,
+334
4841 -73 )
+1.0
+10
(379 -0,
+145
5408 -0 )
+1.0
Roll-Out +10
(400 -0,
+145
5699 -0 )
T4-2-22
(Blank)
T4-2-23
MAIN PUMP P-Q DIAGRAM
• P-Q Control (Torque Control)

• ZAXIS 200-3, 225US-3, 225USR-3
(REFERENCE: Measured at Test Stand) Points on P-Q Line
Delivery Pressure Flow Rate
• Rated Pump Speed: 2
MPa (kgf/cm , psi) L/min (gpm)
-1
ZAXIS 200-3: 1800 min (rpm) A 3.9 (40, 567) 212±3 (56±0.8)
-1
ZAXIS 225US-3: 1800 min (rpm) B 14.7 (150, 2137) [210] ([55])
-1
ZAXIS 225USR-3: 1800 min (rpm) C 17.2 (175, 2500) 187±6 (49±1.6)
-1
ZAXIS 240-3: 1900 min (rpm) D 20.6 (210, 2995) [150] ([40])
-1
ZAXIS 270-3: 2000 min (rpm) E 27.4 (279, 3983) 115±6 (30±1.6)
• Hydraulic Oil Temperature: 50±5 °C (122±41 °F) F 34.3 (350, 4987) 86±6 (23±1.6)
The value indicated in parentheses is only a reference
NOTE: Refer to T4-5-18. value.
• ZAXIS 270-3 Points on P-Q Line

• ZAXIS 240-3 Points on P-Q Line Delivery Pressure Flow Rate
Delivery Pressure Flow Rate 2
MPa (kgf/cm , psi) L/min (gpm)
2
MPa (kgf/cm , psi) L/min (gpm) A 3.9 (40, 567) 236±3 (62±0.8)
A 3.9 (40, 567) 224±3 (59±0.8) B 15.7 (160, 2282) [234] ([62])
B 15.7 (160, 2282) [222] ([59]) C 18.1 (185, 2631) 204±6 (54±1.6)
C 17.6 (180, 2559) 200±6 (53±1.6) D 21.6 (220, 3140) [165] ([44])
D 21.0 (214, 3053) [164] ([43]) E 28.4 (290, 4129) 129±6 (34±1.6)
E 26.5 (270, 3853) 133±6 (35±1.6) F 34.3 (350, 4987) 100±10 (26±2.6)
F 34.3 (350, 4987) 94±10 (25±2.6) The valve indicated in parentheses is only a reference
The valve indicated in parentheses is only a reference valve.
valve.
L/min A
B
Flow D
Rate
Delivery Pressure MPa (kgf/cm2)

T178-04-05-001
T4-2-24
• P-Q Control by Pump Control Pilot Pressure Signal
(REFERENCE: Measured at Test Stand) • ZAXIS 200-3, 225US-3, 225USR-3

Points on P-Q Line
• Rated Pump Speed: Pump Control Pressure Flow Rate
-1 2
ZAXIS 200-3: 1800 min (rpm) MPa (kgf/cm , psi) L/min (gpm)
-1
ZAXIS 225US-3: 1800 min (rpm) 1.7±0.05
-1
ZAXIS 225USR-3: 1800 min (rpm) A 64±2 (17±0.5)
-1
ZAXIS 240-3: 1900 min (rpm) (17±0.5, 247±7)
-1
ZAXIS 270-3: 2000 min (rpm) B 2.0 (20, 291) [94] ([25])
• Hydraulic Oil Temperature: 50±5 °C (122±41 °F)
2.9+0.05−0.29
C 212±3 (56±0.8)
(30+0.5−3, 421+7−42)
NOTE: Refer to T4-5-20.
The value indicated in parentheses is only a reference
value.
• ZAXIS 230-3 Points on P-Q Line • ZAXIS 270-3 Points on P-Q Line
Pump Control Pressure Flow Rate Pump Control Pressure Flow Rate
2
2
MPa (kgf/cm , psi) L/min (gpm) MPa (kgf/cm , psi) L/min (gpm)
A A 1.8±0.05 100±2
1.8±0.05
84±2 (22±0.5) (18.4±0.5, 261±7) (26±0.5)
(18.4±0.5, 261±7)
B B 2.0 (20, 291) [118] ([31])
2.0 (20, 291) [100] ([26])
C C 2.9+0.05−0.29 236±3
2.9+0.05−0.29 224±3
(30+0.5−3, 421+7−42) (59±0.8) (30+0.5−3, 421+7−42) (62±0.8)
L/min
C
Flow
Rate
MPa (kgf/cm2)
Pump Control Pressure
T178-04-05-002
T4-2-25
SENSOR ACTIVATING RANGE
1. Checking Method
• Hydraulic Oil Temperature: 50 ± 5 °C (122±41 °F)

• Unless specified:
Engine Power
Auto-Idle
Control Mode Work Mode
Switch
Dial Switch
Digging
Fast Idle P Mode OFF
Mode
• Monitor each sensor by using Dr. ZX.
2. Sensor Activating Range
Sensor Operation Specification

Fast Idle 0.3 to 1.0 V
Engine Control Dial
Slow Idle 4.0 to 4.7 V
Control Lever: Neutral 0 to 0.1 MPa
2
Pilot Shut-Off Lever: LOCK (0 to 1.0 kgf/cm , 0 to 14.5 psi)
Pressure Sensor
Control Lever: Full Stroke 3.3 to 3.9 MPa
2
Pilot Shut-Off Lever: UNLOCK (34 to 40 kgf/cm , 480 to 566 psi)
Pump Control Control Lever: Neutral 0 to 1 MPa
2
Pressure Sensor (0 to 10 kgf/cm , 0 to 145 psi)
Control Lever: Full Stroke 2.9 to 3.9 MPa
2
(30 to 40 kgf/cm , 421 to 566 psi)
T4-2-26
(Blank)
T4-2-27
ZX200-3 CLASS DR. ZX MONITOR INDI-
CATING VALUES
Unless specified, test under the following conditions. ∗
NOTE: Items marked ( ) are measurable by using
Engine Speed: Fast Idle service menu/monitoring in the monitor
Work Mode: Digging Mode unit.
Power Mode Switch: P mode ∗∗
Items marked ( ) are measurable by using
Auto-Idle: OFF
service menu/monitoring in the monitor unit.
However, it may be difficult to read the
measured value while operating the ma-
chine.
Reference Measured Value

Item Remarks
Value First Second Third Average
PUMP 1 PRESSURE (MPa)
∗
Control Lever in Neutral 0.7
∗
Boom Raise 37.1 When relieving
∗
Boom Lower -
∗
Arm Roll-in 35.6 When relieving
∗
Arm Roll-Out 35.4 When relieving
∗
Bucket Roll-Out 359 When relieving
Bucket Roll-In* 35.9 When relieving
Boom Raise + Arm 34.7 When relieving
Roll-In + Bucket Roll-In
∗
Combined Operation
∗
∗
∗
Boom Lower -
∗
∗
∗
Bucket Roll-Out 0.7 When relieving
∗
Bucket Roll-In 0.7 When relieving
∗
Combined Operation
T4-2-28

Item Remarks
PUMP 1 PUMP CONTROL
PRESSURE (MPa)
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
Boom Raise + Arm Roll-In 3.53 When relieving
+ Bucket Roll-In Combined
∗
Operation
PUMP 2 PUMP CONTROL
PRESSURE (MPa)
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
∗
Operation
T4-2-29

Item Remarks
TARGET ENGINE SPEED (min-1)
∗
Fast Idle 1700
Fast Idle When relieving
∗ 1800
(When operating a control lever) boom raise
∗
Fast Idle (HP Mode) 2000 When relieving
boom raise
∗
Fast Idle (E Mode) 1650 When relieving
boom raise
∗
Auto-Idle 1200
∗
Slow Idle 800
ACTUAL ENGINE SPEED (min-1)
∗
Fast Idle 1704
∗ 1804
∗
boom raise
∗
boom raise
∗
Auto-Idle 1202
∗
Slow Idle 806
ENGINE SPEED DEVIATION
(min-1)
∗
Fast Idle 4
∗ 4
∗
boom raise
∗
boom raise
∗
Auto-Idle 2
∗
Slow Idle 6
DIAL ANGLE (Volt)
∗
Minimum 0.56
∗
Maximum 4.41
T4-2-30

Item Remarks
BOOM RAISE PILOT 4.08 When relieving
∗
CONTROL PRESSURE (MPa) boom raise
ARM ROLL-IN PILOT 4.03 When relieving arm
∗
CONTROL PRESSURE (MPa) roll-in
SWING PILOT CONTROL 4.03 When relieving
∗
PRESSURE (MPa) swing
TRAVEL PILOT CONTROL 4.01
∗
PRESSURE (MPa)
FRONT ATTACHMENT 4.01 Operate either of
∗
CONTROL PRESSURE (MPa) boom, arm, bucket
or swing
DIGGING REGENERATIVE 3.19 When relieving arm
PROPORTIONAL VALVE roll-in
OUTPUT (MPa)
PUMP TORQUE PROPOR- 0.33 Engine fast idle +
TIONAL VALVE OUTPUT (MPa) when relieving arm
roll-in
PUMP 1 LOAD RATE When relieving arm
69
roll-in
70
roll-in
ARM REGENERATIVE PRO- 2.74 Arm leveling
PORTIONAL VALVE OUTPUT*
(MPa)
POWER DIGGING CONTROL
PRESSURE* (MPa)
During operation 2.99
When relieving boom raise 2.99
TRAVEL MOTOR CONTROL 2.99 Travel mode switch:
PRESSURE* (MPa) Fast, When travel-
ing
PUMP TORQUE PROPOR- 537 When relieving arm
TIONAL VALVE OUTPUT FB roll-in
(mA)
DIGGING REGENERATIVE 515 When relieving arm
OUTPUT FB (mA)
ARM REGENERATIVE PRO- 470 Arm leveling
PORTIONAL VALVE OUTPUT
FB (mA)
POWER DIGGIN CONTROL 272
PRESSURE FB (mA)
TRAVEL MODE CONTROL 507 Travel mode switch:
PRESSURE FB (mA) Fast, When travel-
ing
T4-2-31
ECM
Item Remarks
Engine Torque (％) *
No load 10
When relieving arm roll-in 0
-1
Actual Engine Speed (min ) *
No load 1700
-1
Target Engine Speed (min ) *
No load 1700
Engine Oil Pressure (kPa) *
No load 640
Fuel Rate (L/h)
No load 4.5
When relieving arm roll-in 4.5
Atmospheric Pressure (kPa) * 101
Boost Pressure (kPa) *
No load 114
Battery Voltage (V) 29
T4-2-32
(Blank)
T4-2-33
ZX225US-3 CLASS DR. ZX MONITOR IN-
DICATING VALUES
Auto-Idle: OFF
chine.

Item Remarks
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
Combined Operation
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
∗
Combined Operation
T4-2-34

Item Remarks
PUMP 1 PUMP CONTROL
PRESSURE (MPa)
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
∗
Operation
PUMP 2 PUMP CONTROL
PRESSURE (MPa)
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
∗
Operation
T4-2-35

Item Remarks
∗
Fast Idle 1700
∗ 1800
∗
boom raise
∗
boom raise
∗
Auto-Idle 1200
∗
Slow Idle 800
∗
Fast Idle 1704
∗ 1804
∗
boom raise
∗
boom raise
∗
Auto-Idle 1202
∗
Slow Idle 806
(min-1)
∗
Fast Idle 4
∗ 4
∗
boom raise
∗
boom raise
∗
Auto-Idle 2
∗
Slow Idle 6
DIAL ANGLE (Volt)
∗
Minimum 0.56
∗
Maximum 4.41
T4-2-36

Item Remarks
∗
∗
∗
∗
PRESSURE (MPa)
∗
or swing
OUTPUT (MPa)
roll-in
69
roll-in
70
roll-in
(MPa)
PRESSURE* (MPa)
ing
(mA)
OUTPUT FB (mA)
FB (mA)
PRESSURE FB (mA)
ing
T4-2-37
ECM
Item Remarks
*
Engine Torque (%)
No load 10
-1 *
Actual Engine Speed (min )
No load 1700
-1 *
Target Engine Speed (min )
No load 1700
*
Engine Oil Pressure (kPa)
No load 640
Fuel Rate (L/h)
No load 4.5
*
Atmospheric Pressure (kPa) 101
*
Boost Pressure (kPa)
No load 114
T4-2-38
(Blank)
T4-2-39
ZX225USR-3 CLASS DR. ZX MONITOR
INDICATING VALUES
Auto-Idle: OFF
chine.

Item Remarks
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
Combined Operation
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
∗
Combined Operation
T4-2-40

Item Remarks
PUMP 1 PUMP CONTROL
PRESSURE (MPa)
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
∗
Operation
PUMP 2 PUMP CONTROL
PRESSURE (MPa)
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
∗
Operation
T4-2-41

Item Remarks
∗
Fast Idle 1700
∗ 1800
∗
boom raise
∗
boom raise
∗
Auto-Idle 1200
∗
Slow Idle 800
∗
Fast Idle 1704
Fast Idle 1804 When relieving
∗
∗
boom raise
∗
boom raise
∗
Auto-Idle 1202
∗
Slow Idle 806
(min-1)
∗
Fast Idle 4
Fast Idle 4 When relieving
∗
∗
boom raise
∗
boom raise
∗
Auto-Idle 2
∗
Slow Idle 6
DIAL ANGLE (Volt)
∗
Minimum 0.56
∗
Maximum 4.41
T4-2-42

Item Remarks
∗
∗
∗
∗
PRESSURE (MPa)
∗
or swing
OUTPUT (MPa)
roll-in
69
roll-in
70
roll-in
(MPa)
PRESSURE* (MPa)
ing
(mA)
OUTPUT FB (mA)
FB (mA)
PRESSURE FB (mA)
ing
T4-2-43
ECM
Item Remarks
Engine Torque (%) *
No load 10
-1
No load 1700
-1
No load 1700
No load 640
Fuel Rate (L/h)
No load 4.5
Atmospheric Pressure (kPa) * 101
No load 114
T4-2-44
(Blank)
T4-2-45
CATING VALUES
Auto-Idle: OFF
chine.

Item Remarks
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
Combined Operation
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
∗
Combined Operation
T4-2-46

Item Remarks
PUMP 1 PUMP CONTROL
PRESSURE (MPa)
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
∗
Operation
PUMP 2 PUMP CONTROL
PRESSURE (MPa)
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
∗
Operation
T4-2-47

Item Remarks
∗
Fast Idle 1800
∗ 1900
∗
boom raise
∗
boom raise
∗
Auto-Idle 1200
∗
Slow Idle 800
∗
Fast Idle 1801
∗ 1902
∗
boom raise
∗
boom raise
∗
Auto-Idle 1201
∗
Slow Idle 801
(min-1)
∗
Fast Idle 1
∗ 2
∗
boom raise
∗
boom raise
∗
Auto-Idle 1
∗
Slow Idle 1
DIAL ANGLE (Volt)
∗
Minimum 0.49
∗
Maximum 4.37
T4-2-48

Item Remarks
∗
∗
∗
∗
PRESSURE (MPa)
∗
or swing
OUTPUT (MPa)
roll-in
PUMP 1 LOAD RATE 68 When relieving arm
roll-in
PUMP 2 LOAD RATE 68 When relieving arm
roll-in
(MPa)
PRESSURE* (MPa)
ing
(mA)
OUTPUT FB (mA)
FB (mA)
PRESSURE FB (mA)
ing
T4-2-49
ECM
Item Remarks
Engine Torque (%) *
No load 2
-1
No load 1799
-1
No load 1800
No load 664
Fuel Rate (L/h)
No load 7
Atmospheric Pressure (kPa) * 99.0
No load 116
Battery Voltage (V) 28.9
T4-2-50
(Blank)
T4-2-51
CATING VALUES
Auto-Idle: OFF
chine.

Item Remarks
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
Combined Operation
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
∗
Combined Operation
T4-2-52

Item Remarks
PUMP 1 PUMP CONTROL
PRESSURE (MPa)
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
∗
Operation
PUMP 2 PUMP CONTROL
PRESSURE (MPa)
∗
∗
∗
Boom Lower -
∗
∗
∗
∗
∗
Operation
T4-2-53

Item Remarks
∗
Fast Idle 1900
∗ 2000
∗
boom raise
∗
boom raise
∗
Auto-Idle 1200
∗
Slow Idle 800
∗
Fast Idle 1905
∗ 2006
∗
boom raise
∗
boom raise
∗
Auto-Idle 1195
∗
Slow Idle 800
(min-1)
∗
Fast Idle -1
∗ 3
∗
boom raise
∗
boom raise
∗
Auto-Idle -5
∗
Slow Idle 0
DIAL ANGLE (Volt)
∗
Minimum 0.60
∗
Maximum 4.39
T4-2-54

Item Remarks
∗
∗
∗
∗
PRESSURE (MPa)
∗
or swing
OUTPUT (MPa)
roll-in
54
roll-in
54
roll-in
(MPa)
PRESSURE* (MPa)
ing
(mA)
OUTPUT FB (mA)
FB (mA)
PRESSURE FB (mA)
ing
T4-2-55
ECM
Item Remarks
Engine Torque (%) *
No load 24
-1
No load 1899
-1
No load 1500
No load 480
Fuel Rate (L/h)
No load 9.25
Atmospheric Pressure (kPa) * 101.5
No load 22
Battery Voltage (V) 27.6
T4-2-56
OPERATIONAL PERFORMANCE TEST / Engine Test
ENGINE SPEED
Summary
1. Measure the engine speed by using the monitor
unit or Dr. ZX.)
2. Measure the engine speeds in each mode.
NOTE: If the engine speed is not adjusted correctly,

all other performance data will be unreli-
able. Consequently, measure the engine
speed before performing all other tests in
order to check that the engine speed meets
specification.
Preparation:
1. Select the service menu of monitor (In case of Dr.
ZX, install Dr. ZX first).
2. Warm up the machine until coolant temperature
reaches 50 °C (122 °F) or more, and hydraulic oil
temperature is 50±5 °C (122±41 °F).
T4-3-1
Measurement: Evaluation:
1. Measure the items as shown in the table below. Refer to Operational Performance Standard in Group
2. When measuring, set the switch and test condi- T4-2.
tion as shown in the table below in response to
the engine speed to be measured. Remedy:
Refer to Troubleshooting B in Group T5-4.
NOTE: ECO stands for the auto engine speed re-

-1
duction system by 100 min .
Engine Power
Work
Item Control Mode Auto-Idle Switch Test Conditions
Mode
Dial Switch
Digging
Slow Idle Min. Speed P OFF
Mode
Fast Idle Check in the Dr. ZX special
(With ECO deac- Digging functions with ECO deacti-
Max. Speed P OFF
tivated) Mode vated. Measure engine speed
with the lever in neutral.
Fast Idle Move the pilot shut-off lever to
(Heater control: Digging the UNLOCK position. Meas-
Max. Speed P OFF
OFF) Mode ure engine speed with the lever
in neutral.
Fast Idle Move the pilot shut-off lever to
(Heater control: the LOCK position. Engine
Digging
ON) Max. Speed P OFF speed can be measured only
Mode
when coolant temperature is 5
°C (41 °F) or lower.
Fast Idle Digging Measure engine speed while
Max. Speed P OFF
(Relief operation) Mode relieving the boom raise circuit.
Fast Idle Digging
Max. Speed E Mode OFF
(E mode) Mode
Fast Idle Digging Measure engine speed while
Max. Speed HP Mode OFF
(HP mode) Mode relieving the boom raise circuit.
Check engine speed 4 sec-
Digging
Auto-Idle Max. Speed P ON onds after returning all control
Mode
levers to neutral.
Engine speed can be meas-
Digging
Warming Up Min. Speed P OFF ured only when oil temperature
Mode
is 0 °C (32 °F) or lower.
Switch Panel: Monitor Unit:
Digging Mode
Engine Control Dial
Auto-Idle Switch
Power Mode Switch
T1V1-05-01-007
T1V1-04-03-001
T4-3-2
ENGINE COMPRESSION PRESSURE
Summary:
1. Measure compression pressure in the cylinders
and check for a decline in engine power.
2. Check exhaust gas color. Keep track of engine oil
consumption.
3. Check for abnormalities in the intake system, in-
cluding the air filter.
Preparation:
1. Confirm that valve clearances are correct.
2. Confirm that the batteries are charged properly.
3. Run the engine until the coolant temperature
gauge reaches the operating range.
4. Remove the negative terminal of the battery.
Remove all the glow plugs from each cylinder.
： 20 N⋅m (2.0 kgf⋅m, 14.8 lbf⋅ft)
Lower Head
IMPORTANT: If disconnecting the connector of Injector Cover
injector, fuel cannot be jetted.
Therefore, ECM judges that the fuel
system is faulty and the fault code is
displayed. After measurement, de-
lete the displayed fault code.
5. Disconnect the connector of injector which is in-

stalled to the lower head cover.
6. Install the negative terminal of the battery.
7. Turn the starter. Exhaust foreign subjects from
the cylinder. T1V1-04-03-006
8. Install a pressure gauge and an adaptor (Isuzu
EN-46722) to the glow plug mounting part. (Suffi- Connector
ciently install them in order to prevent air leak-
age.)
Measurement:
1. Turn the starter and measure compression pres-
sure of each cylinder.
2. Repeat the measurement three times and calcu-
late the mean values.
Evaluation:
Refer to Operational Performance Standard in Group
T4-2.
T1V1-04-03-005
Remedy:
Refer to the engine shop manual.
T4-3-3
VALVE CLEARANCE
Terminal Nut
Summary:
1. Perform the measurement when the engine is
cold.
2. Before starting any work, clean the head cover
mounting area and avoid contamination in the
engine.
Preparation:
1. Remove the head cover.
2. Remove the terminal nut which secures the har-
ness to the injector.
Harness
： 2 N⋅m (0.2 kgf⋅m, 1.5 lbf⋅ft)
3. Remove the harness assembly from the injector.
4. Remove the leak off pipe.
： 12 N⋅m (1.2 kgf⋅m, 8.9 lbf⋅ft)
5. Rotate the crank pulley. Align the top dead center Injector
(TDC) mark on crank pulley with the top mark lo-
T1V1-04-03-008
cated on timing gear case.
NOTE: When rotating the crank pulley, remove the

fan guard. Then, rotate the fan while hold-
ing the fan belt. If it is difficult to rotate, re-
move all glow plugs and release compres-
sion pressure.
6. Check if piston No.1 (or piston No.4) is now posi-

tioned at the TDC in the compression stroke.
Leak Off Pipe
NOTE: Move push rods for the intake and exhaust

valves on the No.1 cylinder up and down
T1V1-04-03-007
by hand. If any clearances on the both
ends of the push rods are found, piston
Top Mark Crank Pulley
No.1 is positioned at TDC in the compres-
sion stroke. (If the exhaust valve of cylinder
No.1 is pushed down, piston No.4 is posi-
tioned at TDC in the compression stroke.
7. Start measurement from the cylinder (No.1 or

No.4) positioned at TDC in the compression
stroke.
TDC Mark
T1V1-04-03-004
T4-3-4
Measurement:
1. Insert a thickness gauge into the clearance be- Rocker Arm
tween rocker arm and bridge cap end and meas-
ure the valve clearance.
NOTE: The cylinders are aligned from No.1 to

No.4 in that order, as viewed from the fan
side. Injection Order: 1-3-4-2
2. When measurement is started from No.1 cylinder,

perform the same measurement to all valves in-
dicated with the mark “○” in the table below.
(When measurement is started from No.4 cylinder,
perform the measurement in the valves shown
with mark “×”.) T17P-04-03-001
Bridge Cap
Cylinder No. No.1 No.2 No.3 No.4

Valve locations I E I E I E I E
When the measurement is
{ { { {
started from No.1 cylinder
When the measurement is
× × × ×
started from No.4 cylinder
3. Rotate the crankshaft 360°. Align the TDC mark

with the pointer. Continue measurement of other
valves in the same way.
Evaluation:
T4-2.
T4-3-5
Adjustment: Adjusting
If the measurement results are out of specification, Screw Rocker Arm
adjust the valve clearance in the same order of
measurement.
IMPORTANT: Touch the bridge to the end of valve

heads (2 used) horizontally and ad-
just the valve clearance carefully.
1. Loosen the lock nuts (8 used) and adjusting

screws (8 used), which secure the bridge and
rocker arm.
2. Insert a thickness gauge into the clearance be-
tween rocker arm and bridge cap.
3. Tighten the adjusting screw of rocker arm until
condition for the thickness gauge is proper.
4. Tighten the lock nut of rocker arm. T1V1-04-03-002
: 22 N⋅m (2.2 kgf⋅m, 16.2 lbf⋅ft) Lock Nut Bridge Bridge Cap
5. Tighten the adjusting screw of bridge until the
bridge comes in contact with the valve head.
6. Tighten the lock nut of bridge.
: 22 N⋅m (2.2 kgf⋅m, 16.2 lbf⋅ft)
7. Check the valve clearance after the lock nuts are
tightened.
T1V1-04-03-003
Valve Head Bridge
T4-3-6
LUBRICANT CONSUMPTION
Measuring Method
1. Place the machine on level firm ground and leave
the machine for at least one hour in order to let
the lubricant lower to the oil pan when the engine
stops.
At this time, confirm that the machine is level by
using a leveler.
2. Record read-out A (unit: hour) of the hour meter.
3. Replenish the lubricant up to the high-level
gauge.
4. Operate the machine for at least 100 hours or un-
til the oil level lowers to the low-level gauge.
IMPORTANT: Keep the machine-leaving time in

Step 1 above.
5. Place the machine on level firm ground and leave
the machine for at least one hour in order to let
the lubricant lower to the oil pan when the engine
stops.
At this time, confirm that the machine is level by
using a leveler.
6. Record read-out B (unit: hour) of the hour meter.
7. Replenish the lubricant up to the high-level gauge
while measuring the oil-replenishing volume C.
NOTE: When measuring, use a high-precision
measuring cylinder or the like.
8. Determine lubricant consumption from the fol-

lowing equation:
Oil replenishing volume (C) [mL] / Operating hours
(B-A) [hr]
Evaluation:
T4-2.
T4-3-7
(Blank)
T4-3-8
OPERATIONAL PERFORMANCE TEST / Excavator Test
TRAVEL SPEED
Summary: Measurement:
Measure the time required for the excavator to travel 1. Measure at both slow and fast speeds of the
a test track and check the performance of travel machine.
device systems (from main pump to travel motor). 2. Select the following switch positions:
Travel Engine Power
Auto-Idle Work
Preparation: Mode Control Mode
Switch Mode
1. Adjust the track sag on both tracks equally. Switch Dial Switch
2. Prepare a flat and solid test track 10 m (33 ft) in Slow Digging
length with extra length of 3 to 5 m (9.8 to 16 ft) Fast Idle P Mode OFF
Mode Mode
on both ends for machine acceleration and de- Fast Digging
celeration. Fast Idle P Mode OFF
Mode Mode
3. With the arm and bucket fully extended, hold the
bucket 0.3 to 0.5 m (12 to 20 in) above the 3. Start traveling the machine in the acceleration
ground. zone with the travel levers to full stroke.
4. Maintain hydraulic oil temperature at 50±5 °C 4. Measure the time required to travel 10 m (33 ft).
(122±41 °F). 5. After measuring the forward travel speed, turn the
upperstructure 180° and measure the reverse
travel speed.
6. Repeat the measurement three times in each di-
rection and calculate the average values.
Arm Rolled-In, Bucket Rolled-In
End Evaluation:
Bucket Height: 0.3 to 0.5 m Refer to the Operational Performance Standard in
Group T4-2.
Start
10 m Deceleration
Zone Remedy:
3 to 5 m Refer to the Troubleshooting B in Group T5-7.
Acceleration
Zone
3 to 5 m
T105-06-03-001
T4-4-1
TRACK REVOLUTION SPEED
Measure the track revolution cycle time with the track 1. Measure on both tracks at slow and fast travel
raised off ground and check the performance of speeds of the machine.
travel device systems (from main pump to travel 2. Select the following switch positions:
motor). Travel Engine Power
Auto-Idle Work
Mode Control Mode
Switch Mode
Preparation: Switch Dial Switch
1. Adjust the track sag of both side tracks equally. Slow Digging
2. On the track to be measured, put the mark on Mode Mode
one shoe by using a piece of chalk or cloth. Fast Digging
3. Jack up the track to be measured as illustrated. Mode Mode
3. Operate the travel control lever of the track to be
measured to full stroke.
4. Measure the time required for 3 revolutions in
both directions after a constant track revolution
speed is obtained.
90 to 110° 5. Repeat the measurement three times and
calculate the average values.
Evaluation:
Refer to the Operational Performance Standard in
M104-07-067 Group T4-2.
CAUTION: Securely support the raised NOTE: The measurement data obtained through
machine by using the blocks. the raised track revolution test may have
wide variations. Therefore, the evaluation
4. Maintain the hydraulic oil temperature at 50±5 °C based on the results obtained from the 10
(122±41 °F). m travel speed check described before is
more recommendable.
Remedy:
Refer to the Troubleshooting B in Group T5-7.
T4-4-2
MISTRACK CHECK
1. Allow the machine to travel 20 m (65.6 ft). 1. Measure at both slow and fast travel speeds of
Measure the maximum tread deviation from the the machine.
tread chord line drawn between the travel start 2. Select the following switch positions:
and end points and check the performance of Travel Engine Power
Auto-Idle Work
travel device systems (from main pump to travel Mode Control Mode
Switch Mode
motor). Switch Dial Switch
2. If measured on a concrete surface, the tread Slow Digging
deviation has a trend to decrease. Fast Idle P Mode OFF
Mode Mode
Fast Digging
Preparation: Fast Idle P Mode OFF
Mode Mode
1. Adjust the track sag of both tracks equally.
2. Provide a flat, solid test yard 20 m (65.6 ft) in 3. Start traveling the machine in the acceleration
length, with extra length of 3 to 5 m (9.8 to 16 ft) zone with the travel levers at full stroke.
on both ends for machine acceleration and 4. Measure the maximum distance between a
deceleration. straight 20 m (65.6 ft) tread chord line and the
tread made by the machine.
5. After measuring the tracking in forward travel,
Maximum Distance turn the upperstructure 180° and measure in
reverse travel.
6. Repeat the measurement three times and
Acceleration calculate the average values.
Zone:
3 to 5 m
20 m Evaluation:
Group T4-2.
Remedy:
T105-06-03-022

bucket 0.3 to 0.5 m (12 to 20 in) above the
ground.
4. Maintain the hydraulic oil temperature at 50±5 °C
(122±41 °F).
T4-4-3
TRAVEL PARKING LEAKAGE
Summary:
Measure the parking brake function on a specified
slope.
Preparation:
1. The surface of test slope shall be even with a
gradient of 20 % (11.31°).
0.2 to 0.3 m
bucket 0.2 to 0.3 m (8 to 12 in) above the ground.
(122±41 °F).
Measurement: T105-06-03-004
1. Measure the travel parking brake slip amount
while parked.
2. Climb the slope and place the travel levers in
neutral.
3. Stop the engine.
4. After the machine stops, put the matching marks
on a track link or shoe and the track side frame.
5. After 5 minutes, measure the distance between
marks on the track link or shoe and the track
frame.
Evaluation:
Group T4-2.
Displacement measured
after 5 minutes.
T105-06-03-006
T4-4-4
SWING SPEED
Summary:
CAUTION: Prevent personal injury. Always
Measure the time required to swing three complete
make sure that the area is clear and that
turns and check the performance of swing device
co-workers are out of the swing area before
systems (from main pump to swing motor).
starting the measurement.
Preparation:
Measurement:
1. Check lubrication of the swing gear and swing
1. Select the following switch positions:
bearing.
2. Place the machine on flat, solid ground with Engine Control Power Mode Auto-Idle
Work Mode
ample space for swinging. Do not conduct this Dial Switch Switch
test on slopes. Digging
3. With the arm fully retracted and the bucket fully Mode
extended, hold the bucket so that the height of
the bucket pin is the same as the boom foot pin. 2. Operate the swing control lever fully.
The bucket must be empty. 3. Measure the time required to swing 3 turns in one
direction.
4. Operate swing control lever fully in the opposite
direction and measure the time required for 3
turns.
The same height as the
boom foot pin height Evaluation:
T105-06-03-013 Group T4-2.
NOTE: In case a sufficient space for the meas- Remedy:

urement is difficult to find, carry out the Refer to the Troubleshooting B in Group T5-7.
measurement with the boom fully raised
and the arm fully rolled-in.
T178-04-03-001

(122±41 °F).
T4-4-5
SWING FUNCTION DRIFT CHECK
Summary:
1. Measure the swing drift on swing bearing outer
circumference when stopping after a 180°
full-speed swing and check the performance of
swing brake valve.
2. The mechanical brake for swing parking brake is
equipped for the swing motor.
Preparation:
1. Check lubrication of the swing gear and swing Put the matching marks on
bearing. swing bearing outer circumfer-
ence and track frame. T105-06-03-008
2. Place the machine on flat, solid ground with
ample space for swinging. Do not conduct this
test on a slope.
3. With the arm fully retracted and the bucket fully
extended, hold the bucket so that the height of
the bucket pin is the same as the boom foot pin.
The bucket must be empty.
4. Put the matching marks on the swing bearing
outer circumference (upperstructure side) and the
track frame.
5. Swing the upperstructure 180°.
6. Maintain the hydraulic oil temperature at 50±5 °C Before start the measurement, T105-06-03-009
(122±41 °F). swing the upperstructure 180°

T4-4-6
Measurement:
Engine Con- Power Mode Auto-Idle
Work Mode
trol Dial Switch Switch
Digging
Fast Idle P Mode OFF Measure Difference between Marks
Mode
2. Operate the swing control lever fully and return it

to the neutral position when the mark on
upperstructure aligns with that on track frame
after swinging 180° .
3. Measure the distance between the two marks. Mark on Track Frame
4. Align the marks again and swing 180°. Then test
Mark on Swing Bearing
in the opposite direction.
5. Repeat the measurement three times each and
calculate the average values. T105-06-03-010
Evaluation:
Group T4-2.
Remedy:
T4-4-7
SWING MOTOR LEAKAGE
Summary:
Measure the upperstructure drift while suspending a
load on a specified slope and check the performance
of swing parking brake. (The mechanical brake for
swing parking brake is equipped for the swing
device.)
Preparation:
1. Check lubrication of the swing gear and swing
bearing.
2. Load bucket fully. In lieu of loading the bucket,
weight (W) of the following specification can be
used.
ZAXIS200-3: W=1050 kg (2315 lb)
ZAXIS225US-3: W=1050 kg (2315 lb)
ZAXIS225USR-3: W=1050 kg (2315 lb)
ZAXIS240-3: W=1500 kg (3307 lb)
ZAXIS270-3: W=1650 kg (3638 lb)
3. With the arm fully retracted and the bucket fully T105-06-03-011
extended, position the arm top pin height to be
level with the boom foot pin.
4. Park the machine on a smooth slope with a
gradient of 26.8 % (15°).
5. Climb a slope and swing the upperstructure to
position it 90° to the slope. Put the matching
marks on the outer circumference of swing
bearing (upperstructure side) and track frame by
using the tape.
(122±41 °F).
T4-4-8
Measurement:
1. Select the following switch position:
Power Mode
Auto-Idle Switch Work Mode
Switch
P Mode OFF Digging Mode Measure Difference between Marks
2. Maintain the engine at slow idle. After five

minutes, measure difference between the marks
along bearing outer circumference and track
frame.
3. Perform the measurement in both right and left
Mark on Track Frame
swing directions.
4. Repeat the measurement three times in each Mark on Swing Bearing
direction and calculate the average values.
T105-06-03-010
Evaluation:
Group T4-2.
Remedy:
T4-4-9
MAXIMUM SWINGABLE SLANT ANGLE
With the upperstructure swung 90° to the slope, 1. Select the following switch positions:
check the maximum slant angle on which the upper- Engine
Power Mode
structure can swing to the uphill side. Control Auto-Idle Switch Work Mode
Switch
Dial
Preparation: Fast Idle P Mode OFF Digging Mode
1. Check lubrication of the swing gear and bearing.
2. Load the bucket fully. In lieu of loading the bucket,
weight (W) of the following specification can be 2. Operate the swing lever to full stroke and swing
used. the upperstructure to the uphill side.
ZAXIS200-3: W=1050 kg (2315 lb) 3. If the machine can swing, measure the cab floor
ZAXIS225US-3: W=1050 kg (2315 lb) slant angle.
ZAXIS225USR-3: W=1050 kg (2315 lb) 4. Increase the slope angle and repeat steps 2. and
ZAXIS240-3: W=1500 kg (3307 lb) 3. Check both clockwise and counterclockwise.
ZAXIS270-3: W=1650 kg (3638 lb) 5. Repeat the measurement three times.
extended, hold the arm top pin to the position Evaluation:
flush with the boom foot pin height. Refer to the Operational Performance Standard in
4. Climb a slope and swing the upperstructure 90° Group T4-2.
to the slope.
5. Maintain the hydraulic oil temperature at 50±5 °C Remedy:
(122±41 °F). Refer to the Troubleshooting B in Group T5-7.
T105-06-03-011
T4-4-10
(Blank)
T4-4-11
SWING BEARING PLAY
Summary:
Measure the swing bearing play and check the wear
of bearing races and balls.
Preparation:
1. Check the swing bearing mounting bolts for
looseness.
2. Check lubrication of the swing bearing. Confirm
that bearing rotation is smooth without noise.
3. Secure a dial gauge on the round trunk of track
frame by using a magnetic base. Magnetic Dial
4. Position the upperstructure so that the boom Base Gauge
T105-06-03-014
aligns with the tracks facing towards the front
idlers.
5. Position the dial gauge so that its needle point
comes into contact with the bottom surfaceface of
swing bearing outer race.
6. The bucket should be empty.
NOTE: The measured value will vary depending

on where the magnet base is secured. Round Trunk
Secure the magnet base onto the round
trunk or in a position as close to the swing
bearing as possible.
T105-06-03-015
T4-4-12
Measurement:
Measurement: (h1)
extended, hold the bucket 100 mm above the
ground. Record dial gauge reading (h1).
2. Lower the bucket to the ground and raise the
front idler 0.5 m (20 in) by using the front
attachment. Record dial gauge reading (h2).
3. Calculate bearing play (H) from this data (h1 and
h2) as follows:
H=h2-h1 100 mm
Evaluation:
Refer to the Operational Performance Standard in T105-06-03-007
Group T4-2.
Measurement: (h2)
T105-06-03-017
T4-4-13
HYDRAULIC CYLINDER CYCLE TIME
Summary:
1. Measure the cycle time of boom, arm and bucket
cylinders and check the performance of front
attachment systems (from main pump to each
cyliner).
2. The bucket must be empty.
Preparation:
1. Mmeasure at the position as follows.
• Measurement of the cycle time of boom cylinders: T105-06-03-018
With the arm fully retracted and the bucket fully

extended, lower the bucket to the ground.
• Measurement of the cycle time of arm cylinder:
Retract or extend the bucket cylinder so that the
arm and bucket teeth are vertical to the ground.
Set the arm so that the encter of arm operation is
vertical.
• Measuremnt of the cycle time of bucket cylinder:
Adjust each cyliner of boom and arm so that the
center of bucket full stroke is vertical.
(122±41 °F).
0.5 m
T1V1-04-05-005
T105-06-03-020
T4-4-14
Measurement:
Engine Control Power Mode Auto-Idle
Work Mode
Dial Switch Switch
Fast Idle P Mode OFF Digging Mode
2. Measure the cylinder cycle times as follows:

(Cylinder full stroke includes cylinder cushioning
zone.)
• Boom cylinder:
Operate the boom control lever to full stroke.
Measure the time to raise and lower the boom.
• Arm cylinder:
Operate the arm control lever to full stroke.
Measure the time to roll in and roll out the arm.
• Bucket cylinder:
Operate the bucket control lever to full stroke.
Measure the time to roll in and roll out the bucket.
3. Repeat each measurement three times and

Evaluation:
Group T4-2.
Remedy:
T4-4-15
DIG FUNCTION DRIFT CHECK
• Maximum Reach Position
Summary:
1. Measure dig function drift, which can be caused
by oil leakage in the control valve and boom, arm
and bucket cylinders, with the loaded bucket.
2. When testing the dig function drift just after
cylinder replacement, slowly operate each
cylinder for ten minutes to its stroke end and
bleed air. Extended
Retracted
Distance
Distance
Retracted
Distance
Preparation:
1. Load the bucket fully. In lieu of loading the bucket,
Same Height
weight (W) of the following specification can be
used.
Dig Function
ZAXIS200-3: W=1050 kg (2315 lb) Drift Amount
ZAXIS225US-3: W=1050 kg (2315 lb)
ZAXIS225USR-3: W=1050 kg (2315 lb)
ZAXIS240-3: W=1500 kg (3307 lb) T105-06-03-021
ZAXIS270-3: W=1650 kg (3638 lb)

Arm Cylinder Extension
extended, hold the bucket so that height of the
bucket pin is the same as the boom foot pin.
3. Position the arm cylinder with the rod 50 mm (2
in) extended from the fully retracted position.
Position the bucket cylinder with the rod 50 mm Mark
(2 in) retracted from the fully extended position.
(122±41 °F).
Measurement:
1. Stop the engine.
2. Five minutes after the engine has been stopped, T110-06-03-001
measure the change in position of bottom of the

Boom and Bucket Cylinder Retraction
bucket, as well as the boom, arm and bucket
cylinders. Mark Mark
Evalution:
Group T4-2.
Remedy: T110-06-03-002
T4-4-16
• Arm Roll-In Position
Summary:
1. Measure dig function drift, which can be caused
by oil leakage in the control valve and boom, arm
and bucket cylinders.
2. When testing the dig function drift just after
cylinder replacement, slowly operate each
cylinder for ten minutes to its stroke end and
bleed air.
Preparation:
1. The bucket must be empty.
2. With the arm fully extended and the bucket fully
extended, lower the boom until the arm tip is 1 m
(40 in) above the ground.
3. Position the bucket cylinder with the rod 50 mm
(2 in) retracted from the fully extended position.
4. Maintain the hydraulic oil temperature at 50±5 °C 1m
(122±9 °F).
T173-04-03-001
Measurement:
1. Stop the engine.
2. Five minutes after the engine has been stopped,
measure the change in position of bottom of the
arm tip, as well as the boom, arm and bucket
cylinders.
3. Repeat the measuemrent three times and
calculate the average values. Cylinder Retraction
Evalution: Mark Mark

Group T4-2.
Remedy:
T110-06-03-002
T4-4-17
CONTROL LEVER OPERATING FORCE
Summary:
1. Measure a play and operating condition of each
control lever.
2. Measure the maximum operating force of front
attachment control lever.
3. Measure the operating force at the grip center of
each control lever.
Preparation:
Maintain the hydraulic oil temperature at 50±5 °C
(122±41 °F).
CAUTION: Prevent personal injury. Always T107-06-03-003

T107-06-03-004
T4-4-18
Measurement:
1. Measure each control lever.
Engine
Power Mode
Control Auto-Idle Switch Work Mode
Switch
Dial
3. In case of boom (raise), arm and bucket lever,

measure the maximum operating force for each
with each actuator relieved.
4. In case of boom (lower) lever, measure the
maximum operating force with the boom (lower)
relieved by jacking up the machine in a safe area.
5. In case of swing lever, measure the maximum
operating force with swing relieved after securing
the front attachment to prevent swinging.
6. In case of travel lever, raise the track to be
measured. Measure the maximum operating
force required.
late the average values.
Evalution:
Refer to the Orerational Performance Standard in
Group T4-2.
T4-4-19
CONTROL LEVER STROKE
Summary:
1. Check a play and operating condition and
measure each control lever stroke.
2. Measure the lever stroke at the grip center of
each control lever.
3. In case lever stroke play is present in the neutral
position, add half (1/2) the play present to both
side lever strokes.
Preparation:
Maintain the hydraulic oil temperature at 50±5 °C
(122±41 °F).
Measurement: T107-06-03-005
1. Stop the engine.

2. Measure each lever stroke from neutral to the
stroke end of each control lever of boom, arm,
bucket, swing and travel.
3. Repeat the measuement three times and
Evalution:
Refer to the Orerational Performance Standard in
Group T4-2.
T4-4-20
(Blank)
T4-4-21
COMBINED OPERATION OF BOOM RAISE
/ SWING FUNCTION CHECK
Summary:
1. Check boom raise and swing movement and
speeds while operating both functions
simultaneously.
2. Check if the cylinders do not hesitate while oper-
ating the cylinder with the engine running at fast
idle.
Preparation:
extended, lower the bucket onto the ground. The
bucket must be empty.
(122±41 °F).
CAUTION: Prevent personal injury. Always T107-06-03-009

T4-4-22
Measurement:
Engine Control Power Mode Auto-Idle
Work Mode
Dial Switch Switch
2. Raise the boom and roll the swing in full stroke at

the same time.
When the upperstructure rotates 90°, release the
control levers to stop both functions. Measure the
time required to swing 90° and height (H) of the
bucket teeth. (The bucket must be empty.)
calculate the average values. T107-06-03-010
Evalution:
Group T4-2.
Remedy:
T107-06-03-011
T4-4-23
COMBINED OPERATION OF BOOM RAISE
/ ARM ROLL-IN FUNCTION CHECK
Summary:
1. Check boom raise and arm roll-in movement and
speeds while operating both functions
simultaneously. Arm Mounting
2. Check if the cylinders do not hesitate while oper- Pin
ating the cylinder with the engine running at fast
idle.
Preparation:
1. Retract the arm cylinder fully and extend the
bucket cylinder so that the bucket teeth and arm
mounting pin are on a straight line. Adjust the
boom cylinder so that the bucket tooth tip height
is 0.5 m (1 ft 8 in) above the ground. (The bucket 0.5 m
must be empty.)
2. Maintain the hydraulic oil temperature at 50±5 °C T107-06-03-006
(122±41 °F).
Measurement:
1. Select the switch positions as follows.
Engine Power Mode
Auto-Idle Switch Work Mode
Control Dial Switch
2. Raise the boom and roll the arm in full stroke at

the same time.
3. Measure the time required for the arm to reach
the stroke end. (The bucket must be empty.)
late the average value.
Evaluation:
Refer to T4-2 Operational Performance Standard in
Group T4-2. T1V1-04-04-001
Remedy:
Refer to Troubleshooting B in Group T5-7.
T4-4-24
OPERATIONAL PERFORMANCE TEST / Component Test
PRIMARY PILOT PRESSURE
Preparation:
1. Stop the engine.
2. Push the air bleed valve on top of the hydraulic oil
tank and release any remaining pressure.
3. Remove the plug from the pilot filter. Install
adapter (ST 6069) and pressure gauge (ST 6942)
to the pressure check port.
: 14 mm
Plug
4. Start the engine. Confirm that no oil leakage is
observed at the pressure gauge connection.
(122±41 °F).
T178-03-07-001
Measurement:
Engine Power Mode Auto-Idle
Work Mode
Control Dial Switch Switch
Digging
Mode
Digging
Slow Idle P Mode OFF
Mode
2. Measure pilot pressure in each specified setting

above without load.
Evaluation:
Refer to the Performance Standard Table in Group
T4-2.
T4-5-1
Primary Pilot Pressure Adjustment Procedure
Adjustment:
Adjust the relief valve set pressure if necessary.
Relief Valve
1. Remove plug (1) from the relief valve.

: 22 mm
2. Install the estimated number of shims (2). T178-03-07-001
3. After adjustment, tighten plug (1).

+2
: 25 N⋅m (2.5
+0.2
kgf⋅m, 18.4
+1.5
lbf⋅ft) 1
2
5. After adjustment, check the set pressure.
NOTE: Standard Change in Pressure (Reference)

Shim Thickness Change in Relief Pressure
(mm) kPa (kgf/cm 2, psi)
0.25 78 (0.8, 11.3)
0.5 157 (1.6, 22.8)
1.0 304 (3.1, 44.2)
T111-06-04-004
T4-5-2
SECONDARY PILOT PRESSURE
Preparation:
1. Stop the engine.
2. Push the air bleed valve on top of the hydraulic oil Pilot Valve Signal Control Valve
3. Measure pressure at the location between pilot Hose
valve and signal control valve. Remove the pilot
hose from the circuit to be measured. Install the Nipple
hose (9/16-18UNF, Length: approx. 400 mm (16
in)) to the signal control valve side. Install tee
(4351843), adapter (ST 6460), nipple (ST 6069),
coupling (ST 6332) and pressure gauge (ST 6315)
between the hoses. Pressure
Gauge
: 17 mm, 19 mm
Tee
Adapter
NOTE: When removing the lines from signal con-
trol valve, use tool (SNAP-ON
GAN850812B: size 19.05 mm) in order to
easily remove the lines.

(122±41 °F). T1F3-04-05-008
T4-5-3
Measurement:
Work Mode
Digging
Mode
Digging
Mode
2. Measure pilot pressure by using a pressure
gauge with the corresponding control lever oper-
ated to full stroke.
Evaluation:
T4-2.
Remedy:
T4-5-4
SOLENOID VALVE SET PRESSURE
Solenoid Valve
Measure solenoid valve set pressure by using both Dr.
Pressure Gauge
ZX and the pressure gauge.
Preparation:
1. Stop the engine.
3. Remove the line from the solenoid valve to be
measured. Install tee (ST 6451), hose (Parts
Number: 4216453), adapter (ST 6461) and pres- Hose Tee Adapter T157-05-04-002
sure gauge (ST 6942).

: 17 mm, 19 mm, 22 mm
Connect Dr. ZX and select the monitoring func-

tion.
(122±41 °F).
T4-5-5
Measurement:
Work Mode
Digging
Mode
Digging
Mode
SC SF SI SG
2. Operate as instructed below for each measuring

solenoid valve:
Solenoid Valve SG: Turn the power digging switch
ON and OFF.
Solenoid Valve SI: Travel, Stop
Solenoid Valve SF: Relief combined operation of
boom raise and arm roll-in.
Solenoid Valve SC: Combined operation of swing
and arm roll-in.
T1V1-03-07-007
3. Read the values on both Dr. ZX and the pressure

gauge.
Evaluation:
Refer to the performance Standard Table in Group
T4-2.
T4-5-6
Solenoid Valve Adjustment Procedure
7 O-Ring
IMPORTANT: As O-ring is damaged and oil leak-

8
age may cause, do not loosen ad-
justing screw (8) excessively.
Do not loosen adjusting screw (8)
more than 2 turns.
1. Loosen lock nut (7). Turn adjusting screw (8) and
adjust the set pressure.
2. After adjustment, tighten lock nut (7).
: 10 mm
: 3 mm T1V1-04-05-004
: 3 N⋅m (0.3 kgf⋅m, 2.2 lbf⋅ft) 2.0 mm (0.079 in) or less

from end of Lock Nut
3. After adjustment, check the set pressure.
Screw Turns 1/4 1/2 3/4 1
kPa 69 137 206 275
Change in 2
(kgf/cm ) (0.7) (1.4) (2.1) (2.8) 7
Pressure
(psi) (10) (20) (30) (40)
T1V1-04-05-003
7 8
Pressure Pressure
Increase Decrease
W107-02-05-129
T4-5-7
MAIN PUMP DELIVERY PRESSURE
The main pump delivery pressure can also be meas-
ured by using Dr. ZX.
Preparation:
1. Stop the engine.
3. Remove the plug of pressure check port from the
main pump delivery port. Install adapter (ST
6069), hose (ST 6943) and pressure gauge (ST
6941).
: 6 mm

tion.
(122±41 °F).
Measurement:
Work Mode T157-05-04-005
Digging
Mode
2. Measure pressure with the control levers in neu-

tral without load.
Evaluation:
T4-2.
Remedy:
T4-5-8
MAIN RELIEF SET PRESSURE
Summary:
Measure the main relief valve set pressure at the de-
livery port in main pump. (The main relief set pressure
can also be measured by using Dr. ZX.)
Preparation:
1. Stop the engine.
3. Remove the plug of pressure check port from the
main pump delivery port. Install adapter (ST
6069), hose (ST 6943) and pressure gauge (ST
6941).
: 6 mm

tion.
(122±41 °F).
T157-05-04-005
T4-5-9
Measurement:
Work Mode
Digging
Mode
2. First, slowly operate the bucket, arm and boom

control levers to the stroke end and relieve each
function.
3. As for the swing function, secure the upperstruc-
ture so it is immovable. Slowly operate the swing
lever and relieve the swing function.
4. As for the travel function, secure the tracks
against an immovable object. Slowly operate the
travel levers and relieve the travel function.
5. With the power digging switch pushed, slowly op-
erate the bucket, arm and boom control levers to
the stroke ends and relieve each function within
eight seconds.
Evaluation:
Refer to the Performance Standard in Group T4-2.
NOTE: If the measure pressures for all functions

are lower than the specified range, the
probable cause is a decrease of main relief
valve setting pressure.
If relief pressure of a particular function is
lower, the probable cause is other than
main relief valve.
T4-5-10
Main Relief Pressure Adjustment Procedure
Main Relief Valve
Adjustment:
In case of pressure adjustment during power digging
operation, adjust the high-pressure side of main relief
pressure. In case of pressure adjustment in normal,
adjust the low-pressure side of main relief pressure.
• High-Pressure Side of Main Relief Pressure Ad-

justment Procedure
1. Loosen lock nut (1). Lightly tighten plug (3) until
plug (3) comes into contact with the end of piston
(2). Tighten lock nut (1).
: 27 mm
: Plug (3): 19.5 N⋅m (2 kgf⋅m, 14.5 lbf⋅ft)
: Lock Nut (1):
68 to 78 N⋅m
(7 to 8 kgf⋅m, 51 to 58 lbf⋅ft) or less
T1V1-04-05-001
2. Loosen lock nut (4). Turn plug (5) and adjust
pressure until the specified pressure is obtained.
: 27 mm, 32 mm
: Lock Nut (4): 3
78 to 88 N⋅m
(8 to 9 kgf⋅m, 58 to 65 lbf⋅ft) or less 1
4
2
T157-05-04-009
Plugs (5, 3)
Pressure Pressure
Increase Decrease
W107-02-05-127
T4-5-11
• Low-Pressure Side of Main Relief Pressure Ad- Main Relief Valve
justment Procedure
1. Loosen lock nut (1). Turn plug (3) counterclock-
wise until the specified pressure is obtained.
Tighten lock nut (1).
: 27 mm
: Lock Nut (1):
59 to 68 N⋅m
(6 to 7 kgf⋅m, 43 to 51 lbf⋅ft) or less
2. After adjustment, check the set pressures.
T1V1-04-05-001
NOTE: Standard Change in Pressure (Reference) 3

Plug Turns 1/4 1/2 3/4 1
Change in Relief MPa 7.1 14.2 21.3 28.4 1
2
Pressure: Plug (5) (kgf/cm ) (72.5) (145) (217.5) (290)
(High-Pressure Side) (psi) 5
(1030) (2060) (3090) (4120)
Change in Relief MPa 5.3 10.7 16.0 21.3
2 4
Pressure: Plug (3) (kgf/cm ) (54) (109) (163) (217)
(Low-Pressure Side) (psi) (770) (1550) (2320) (3090) 2
T157-05-04-009
Plugs (5, 3)
Pressure Pressure
Increase Decrease
W107-02-05-127
T4-5-12
RELIEF PRESSURE (WHEN RELIEVING Swing Relief Valve
SWING)
ZX200-3 class, ZX225US-3 class, ZX225USR-3
class, ZX240-3 class
Adjust pressure by changing the number of shims
(2).
1. Remove the swing relief valve.

: 41 mm
2. Remove plug (5), sleeve (4) and piston (3).

: 30 mm
3. Install shims (2) between piston (3) and spring

seat (1) in order to adjust pressure.
4. After adjustment, install piston (3), sleeve (4) and

plug (5).
: 118 N⋅m (12 kgf⋅m, 88 lbf⋅ft)
NOTE: Replace seals (A, B, C) with new ones.

A: JIS B 2401 G30 1B T1V1-03-02-003
B: AS568-023 (Aero-Space Standard)

C: AS568-125 (Aero-Space Standard)
5. Install the swing relief valve. 1 2 3 4 5

: 176 N⋅m (18 kgf⋅m, 130 lbf⋅ft)
6. Check the set pressure.

Shim (2) Thickness Change in Pressure
(mm) kPa (kgf/cm 2, psi)
0.1 610 (6.3, 60) A B C T178-03-02-005
T4-5-13
ZX270-3 class
Loosen lock nut (2) and adjust pressure by using Swing Relief Valve
adjusting screw (1).
1. Loosen lock nut (2).

:24 mm, 32 mm
2. Turn adjusting screw (1) in order to adjust pres-

sure.
3. Tighten lock nut (2).

: 24 mm, 32 mm
: 177 N⋅m (18 kgf⋅m)

Adjusting Screw
1/4 1/2 3/4 1 T1V1-03-02-003
Turns
Change MPa 2.5 5.0 7.5 10.0
1 2
in (kgf/cm2) (25.5) (51) (76.5) (102)
Pressure (psi) (363) (725) (1088) (1450)
T107-02-04-020
Pressure Pressure
Increase Decrease
T157-05-04-023
T4-5-14
OVERLOAD RELIEF VALVE SET PRES-
SURE
Summary:
1. The circuit pressure must be increased by apply- 3. If the overload relief valve performance must be
ing an external force while blocking the return cir- checked on the machine, however, measure the
cuit from the control valve. This measuring main relief pressure while releasing each front
method is hazardous and the results obtained function respective to the measuring overload re-
with this method are unreliable. lief valve. And, assume that the overload relief
2. The oil flow rate used to set the overload relief valve is functioning correctly if the obtained main
pressure is far less than that used to set the main relief pressure is within the specified value range.
relief pressure. Therefore, measuring the over- Measure the main pressure of the front functions
load pressure in the main circuit by increasing the by using Dr. ZX as follows:
main relief set pressure more than the overload
valve set-pressure is not a proper method. In ad- Preparation:
dition, in case a main relief valve designed to leak 1. Stop the engine.
a small quantity of oil before reliving is used, its 2. Push the air bleed valve on top of the hydraulic oil
pre-leaking start pressure must be increased tank and release any remaining pressure.
more than the overload relief valve set pressure. 3. Remove the plug from pressure check port of
However, the pre-leaking start pressure is not al- main pump delivery port. Install adapter (ST
ways increased more than the overload relief 6069), hose (ST 6943) and pressure gauge (ST
valve set-pressure as the adjustable upper limit of 6941).
the main relief valve set-pressure is provided. : 6 mm
Accordingly, the overload relief valve assembly
should be removed from the machine and 4. Connect Dr.ZX and select the monitoring function.
checked on a specified test stand at a correct oil Start the engine. Confirm that no oil leakage is
flow rate. Some overload relief valves come in observed at the pressure gauge connection.
contact with the control valve body to block the oil
passage. When this type of overload relief valve 5. Maintain the hydraulic oil temperature at 50±5 °C
is checked, the control valve body must be pre- (122±41 °F).
cisely finished as the test unit. Provide one con-
trol valve other than that on the machine as a test
kit.
T4-5-15
Measurement:
Work Mode
Digging
Mode
2. Slowly operate the bucket, arm or boom control

levers to the stroke ends and relieve each func-
tion.
3. Read pressures on the pressure gauge at this
time.
4. Perform the measurement for the bucket, arm
and boom in that order.
late the average value for each.
Evaluation:
1. Performance of the overload relief valves are
normal if the measured main relief pressures are
within the specified value range. T157-05-04-005
Refer to the Performance Standard in Group

T4-2.
T4-5-16
Overload Relief Valve Pressure Adjustment Pro-
cedure
NOTE: In principle, adjust the overload relief valve

pressure on a test stand.
Loosen lock nut (1) and adjust pressure by using ad-

justing screw (2).
1
1. Loosen lock nut (1).
: 17 mm
2. Turn adjusting screw (2) in order to adjust pres-

sure.
: 6 mm
2
3. Tighten lock nut (1). W107-02-05-128
: 17 mm
: 29.5 N⋅m (3.0 kgf⋅m, 22 lbf⋅ft)

Adjusting Screw (2)
1/4 1/2 3/4 1 2
Turns
MPa 5.2 10.6 15.9 21.1
Change in 2
(kgf/cm ) (54) (108) (162) (216)
Pressure
(psi) (770) (1540) (2300) (3070)
Pressure Pressure
Increase Decrease
W107-02-05-129
T4-5-17
MAIN PUMP FLOW RATE MEASUREMENT
•P-Q Control (Torque Control)

Summary:
Main pump performance is checked by measuring 5. Install a pressure gauge to the main pump to be
the pump flow rate by using a hydraulic tester in- measured. (Refer to “Main Relief Set Pressure”.)
stalled at the main pump delivery port (one side) to : 6 mm
be measured. Use Dr. ZX and a pressure gauge at 6. Remove pipe (13) from the regulator. Install plug
the same time. (G 1/4) to pipe (13) in the regulator.
: 17 mm
IMPORTANT: This measurement procedure is a 7. Remove the vacuum pump. Loosen plug (12) on
simple method. The measured data top of the pump casing. Bleed air from the casing
will be lower by approx. 5 % than the until oil only comes out.
accurately measured value. In order 8. Fully open the loading valve of hydraulic tester.
to measure accurately, disconnect 9. Start the engine. Check the pressure gauge con-
the return circuit from the control nection for any oil leaks. Install Dr. ZX and select
valve and connect it to the hydraulic the monitoring function.
oil tank.
Measurement:
Preparation: 1. Maintain the hydraulic oil temperature at 50±5 °C
1. Stop the engine. Push the air bleed valve and (122±41 °F).
bleed air. Install a vacuum pump to the oil filler 2. Measure the maximum flow rate.
port. 3. Select each switch position as follows:
NOTE: Operate the vacuum pump while connect- Engine Power Mode Auto-Idle
Work Mode
ing the pump flow rate test line. Control Dial Switch Switch
2. Remove the delivery hose from main pump (one Digging
side) to be measured. Install pipe (1 or 2) by us- Mode
ing the split flanges and bolts which were used for
the removed delivery hose. 4. Adjust the relief set pressure of main relief valve
: 41 mm in control valve to each pressure point specified
: 10 mm along the main pump P-Q curve. (Refer to
3. Install pipe (1 or 2) to hydraulic tester (5) by using T4-2-13) Slowly restrict the loading valve of hy-
test hose (3) and adapter (4). Install adapter (6), draulic tester while relieving pressure in the arm
joint (7), test hose (8) and flange (9) to hydraulic roll-in circuit. Measure the flow rates and engine
tester (5). speeds at each pressure point specified in the
: 41 mm P-Q curve.
: 10 mm 5. Repeat each measurement three times and cal-
4. Install the delivery hose to flange (9) with split culate the average values.
flanges (10) and bolt (11).
: 10 mm
T4-5-18
Evaluation:
1. Convert the measured flow rates to those at the 2. Standard Flow Rate
specified engine speed by using the following Refer to Operational Performance Standard in
formulas: Group T4-2.
NOTE: When actually measuring, install pipe (1 or
Qc = (Ns × Q) ⁄ Ne 2) only to the pump to be measured.
Qc : Converted Flow Rate

Q : Measured Flow Rate
Ns : Specified Engine Speed
-1
(ZAXIS200-3: 1800 min )
-1
(ZAXIS225US-3: 1800 min )
-1
(ZAXIS225USR-3: 1800 min )
-1
(ZAXIS240-3: 1900 min )
-1
(ZAXIS270-3: 2000 min )
Ne : Measured Engine Speed:
Values indicated on Dr. ZX
1, 2 3 4 5 6 7 8 9 10 11
Delivery Hose
(To Control Valve)
T173-04-04-002
13
T1V1-04-05-002
12
1 - Pipe E (ST 6144) 5 - Hydraulic Tester (ST 6299) 8- Test Hose (ST 6320) 11 - Bolt (ST 6409) (4 Used)
2 - Pipe B (ST 6143) 6 - Adapter PF1 × UNF1-7/8 9- Flange (ST 6118) 12 - Plug
(ST 6146)
3 - Test Hose (ST 6145) 7 - Joint (ST 6330) 10 - Split Flange (ST 6130) 13 - Pipe
4 - Adapter PF1 × UNF1-7/8
(ST 6146)
T4-5-19
•Pilot Characteristics
Summary:
Main pump performance is checked by measuring 5. Install hose (19) and adapter (20) to port T of
the pump flow rate by using a hydraulic tester in- pressure reducing valve (16). Remove plug L
stalled at the main pump delivery port (one side) to from the return pipe. Install hose (19).
be measured. Use Dr. ZX and a pressure gauge at : 19 mm, 22 mm
the same time. 6. Remove pipe (21) from the regulator. Install plug
(G 1/4) to the mounting hole for pipe (21) in the
IMPORTANT: This measurement procedure is a regulator.
simple method. The measured data : 17 mm
will be lower by approx. 5 % than the 7. Remove the vacuum pump. Loosen the plug from
accurately measured value. In order top of the pump casing. Bleed air from the pump
to measure accurately, disconnect casing until oil only comes out.
the return circuit from the control 8. Fully open the loading valve of hydraulic tester.
valve and connect it to the hydraulic 9. Start the engine. Check the connections for any
oil tank. oil leaks.
Preparation:
1. While referring to steps 1 to 4 on page T4-5-18.
Install a hydraulic tester to the main pump to be
measured.
2. Remove the hose from regulator port Pi of the
pump to be measured. Install plug (ST 6213) to
the removed hose.
: 6 mm, 19 mm
3. Install adapters (15) (3 used) to pressure reduc-
ing valve (16). Remove plug M from the pilot filter.
Install adapter (13) and hose (14) to the pilot filter.
Install hose (14) to regulator port P1 on pressure
reducing valve (16).
: 19 mm
4. Install tee (17) to port P2 of pressure reducing
valve (16). Install pressure gauge (18) and hose
(14) to tee (17). Install hose (14) to the regulator.
: 19 mm
T4-5-20
1, 2 3 4 5 6 7 8 9 10 11
Delivery Hose
(To Control
Valve)
T173-04-04-002
21 Port Pi
Plug M
T178-03-07-001
12
T1V1-04-05-002
Pressure Reducing Valve Port Position

Pressure Reducing Return Pipe
Valve
T L
20
18
P1 P2 19
15
To Regulator To Pilot Filter

Port Pi
14 17 15 16 15 14 13
T178-04-04-004
1 - Pipe E (ST 6144) 7 - Joint (ST6330) 12 - Plug M 17 - Tee UNF7/16 × UNF7/16×
PF1/4
(ST 6451)
2 - Pipe B (ST 6143) 8 - Test Hose (ST 6320) 13 - Adapter UNF7/16 × PF1/4 18 - Pressure Gauge
(ST 6069) (ST 6931)
3 - Test Hose (ST 6145) 9 - Flange (ST 6118) 14 - Hose UNF7/16 × UNF7/16 19 - Hose UNF7/16 × UNF7/16
(4334309) (4334309)
4 - Adapter PF1 × UNF1-7/8 10 - Split Flange (ST 6130) 15 - Adapter PF3/8 × UNF7/16 20 - Adapter PF3/8 × UNF7/16
(ST 6146) (4200465) (4200465)
5 - Hydraulic Tester (ST 6299) 11 - Bolt (ST 6409) (4 Used) 16 - Pressure Reducing Valve 21 - Pipe
(4325439)
(ST 6146)
T4-5-21
Measurement:
1. Maintain the hydraulic oil temperature at 50±5 °C Evaluation:
(122±41 °F) 1. Convert the measured flow rates to those at the
2. Measure pump flow rate in response to the ex- specified engine speed by using the following
ternal command pilot pressure. formulas:
3. Select each switch position as follows:
Engine Power Mode Auto-Idle Qc = (Ns × Q) ⁄ Ne
Work Mode
Digging Qc : Converted Flow Rate
Fast Idle P Mode OFF Q : Measured Flow Rate
Mode
4. Adjust the pressure reducing valve set pressure Ns : Specified Engine Speed
-1
to each pressure point specified along the main (ZAXIS200-3: 1800 min )
-1
pump P-Q curve. (Pilot Characteristics) (Refer to (ZAXIS225US-3: 1800 min )
-1
T4-2-16.) Measure the flow rates and engine (ZAXIS225USR-3: 1800 min )
-1
speeds at the pressure points specified in the (ZAXIS240-3: 1900 min )
-1
P-Q curve. (ZAXIS270-3: 2000 min )
5. Repeat each measurement three times and cal- Ne : Measured Engine Speed
culate the average values. Values indicated on Dr. ZX
2. Standard Flow Rate

Refer to Operational Performance Standard in
Group T4-2.
NOTE: When actually measuring, install pipe (1)
(ST 6144) or (2) (ST 6143) only to the
pump to be measured.
T4-5-22
1, 2 3 4 5 6 7 8 9 10 11
Delivery Hose
(To Control
Valve)
T173-04-04-002
21 Port Pi
Plug M
T178-03-07-001
12
T1V1-04-05-002
Pressure Reducing Valve Port Position

Pressure Reducing Return Pipe
Valve
T L
20
18
P1 P2 19
15
To Regulator To Pilot Filter

Port Pi
14 17 15 16 15 14 13
T178-04-04-004
7 - Pipe E (ST 6144) 12 - Joint (ST6330) 17 - Plug M 22 - Tee UNF7/16 × UNF7/16×
PF1/4
(ST 6451)
8 - Pipe B (ST 6143) 13 - Test Hose (ST 6320) 18 - Adapter UNF7/16 × PF1/4 23 - Pressure Gauge
(ST 6069) (ST 6931)
9 - Test Hose (ST 6145) 14 - Flange (ST 6118) 19 - Hose UNF7/16 × UNF7/16 24 - Hose UNF7/16 × UNF7/16
(4334309) (4334309)
10 - Adapter PF1 × UNF1-7/8 15 - Split Flange (ST 6130) 20 - Adapter PF3/8 × UNF7/16 25 - Adapter PF3/8 × UNF7/16
(ST 6146) (4200465) (4200465)
11 - Hydraulic Tester (ST 6299) 16 - Bolt (ST 6409) (4 Used) 21 - Pressure Reducing Valve 26 - Pipe
(4325439)
(ST 6146)
T4-5-23
Regulator Adjustment
6 5 1
2
10
4 3
7 8
T1V1-03-01-009
1 - Lock Nut (For Minimum 4 - Adjusting Screw (For 7 - Lock Nut 9 - Lock Nut
Flow Rate) Maximum Flow Rate) (For P-Q Control) (For P-Q Control)
2 - Adjusting Screw (For 5 - Lock Nut 8 - Adjusting Screw 10 - Adjusting Screw
Minimum Flow Rate) (For Pilot Pressure Char- (For P-Q Control) (For P-Q Control)
acteristic)
3 - Lock Nut (For Maximum 6 - Adjusting Screw
Flow Rate) (For Pilot Pressure Char-
acteristic)
Adjustment Item Adjustment Procedure Remarks

1. Minimum Flow Rate Loosen lock nut (1) and turn ad- 1) Do not turn adjusting screw (2) more
justing screw (2). than two turns.
Rotating adjusting screw (2) 1/4 2) Securely tighten lock nut (1) after
a turn clockwise increases the adjustment.
minimum pump flow rate by 6.56
3 3
cm /rev. (0.4 in /rev).
: 17 mm
: 19.6 N⋅m
(2 kgf⋅m, 14.4 lbf⋅ft)
2. Maximum Flow Rate Loosen lock nut (3) and turn ad- 1) Do not turn adjusting screw (4) more
justing screw (4). than two turns.
Rotating adjusting screw (4) 1/4 2) Do not increase the maximum flow
a turn clockwise decreases the rate.
maximum pump flow rate by In other words, do not turn adjusting
3 3
8.22 cm /rev. (0.5 in /rev). screw (4) counterclockwise.
: 13 mm 3) Securely tighten lock nut (3) after
: 9.8 N⋅m adjustment.
(1 kgf⋅m, 7.2 lbf⋅ft)
T4-5-24
Adjustment Item Adjustment Procedure Remarks

3. Pilot Pressure Characteristics Loosen lock nut (5) and turn ad- 1) Do not turn adjusting screw (6)
justing screw (6). more than one turn.
Rotating adjusting screw (6) 1/4 2) When adjusting screw (6) is turned
a turn clockwise decreases the clockwise, the maximum flow rate
3
flow rate by 13.2 cm /rev. will also be decreased.
Q 3
(0.71 in /rev). In order to maintain the maximum
: 30 mm flow rate unchanged, turn adjusting
: 29.4 N⋅m screw (4) counterclockwise twice as
(3 kgf⋅m, 21.7 lbf⋅ft) much as adjusting screw (6) is
turned.
This ratio of 2 (adjusting screw (4)
counterclockwise turn) to 1 (adjust-
ing screw (6) clockwise turn) is to
Pi
counterbalance.
3) Securely tighten lock nut (5) after
adjustment.
4. P-Q Control A: Loosen lock nut (7) and turn 1) Do not turn the adjusting screws
(Torque Adjustment) adjusting screw (8). more than one turn.
Rotating adjusting screw (8) 2) Rotate the adjusting screws watch-
Q 1/4 a turn clockwise increases ing the engine performance.
3
the flow rate by 15.3 cm /rev. 3) Securely tighten lock nut (7) or (9)
3
A (0.93 in /rev.). after adjustment.
B: Loosen lock nut (9) and turn
adjusting screw (10).
Rotating adjusting screw (10)
1/4 a turn clockwise increases
3
the flow rate by 3.60 cm /rev.
Pd 3
(0.22 in /rev).
Pd
T4-5-25
SWING MOTOR DRAINAGE
Summary:
1. Measure amount of oil draining from the
swing motor while swinging the upperstruc-
ture and check the swing motor perform-
ance.
2. The amount of drain oil from the swing motor
will change depending on hydraulic oil tem-
perature.

Also, take care not to fall off the machine
while the measurement.
Preparation:
1. Maintain hydraulic oil temperature at 50±5 °C
(122±41 °F). Rotate the swing motor in order to
warm inside of the motor.
T157-05-04-014
2. Stop the engine. Push air bleed valve (1) on top

of the hydraulic oil tank and release any remain-
ing pressure.
2
3. Remove drain hose (2) of the swing motor at the
hydraulic oil tank end. Install plug (ST 6213) to
the Remove end on the hydraulic oil tank.
: 22 mm
: 39 N⋅m (4 kgf⋅m, 29 lbf⋅ft)
T178-04-04-005
T4-5-26
Preconditions for Measurement:
Work Mode
Digging
Mode
Measurement:
1. Amount of Oil Drained While Swinging the Up-
perstructure The same height as
(1) Fully retract the arm cylinder. Fully extend the boom foot pin height
bucket cylinder. Hold the boom so that the
T105-06-03-013
arm tip pin height is the same as the boom
foot pin height. The bucket must be empty.
(2) Start the engine. Operate and hold the swing
lever full stroke. After the swing speed
reaches a constant maximum speed, start
draining oil measurement when drain oil starts
coming out of the drain hose end.
(3) Repeat the measurement at least three times
in both clockwise and counterclockwise direc-
tions, and calculate the average values.
(4) The measuring time should be more than 45
seconds.
2. Amount of Oil Drained While Relieving Swing T107-06-06-005

Motor Circuit
(1) Thrust the bucket teeth into the ground so
that the upperstructure does not rotate.
(2) Start the engine. Operate and hold the swing
lever full stroke. Start draining oil measure-
ment when drain oil starts coming out of the
drain hose end.
in both clockwise and counterclockwise direc-
tions, and calculate the average values.
seconds.
T4-5-27
Evaluation:
Group T4-2.
∗ Conversion of amount of drain oil measured into

the per-minute value
First measure amount of drain oil by using a cali-

brated container. Then, convert the measured
drain oil into the per-minute value by using the for-
mula below:
∆Q = 60 × q / t
∆Q : Amount of drain oil per minute (L/min)

t : Measured time (seconds)
q : Total amount of drain oil (L)
T107-06-05-008
T4-5-28
TRAVEL MOTOR DRAINAGE
Summary:
1. While rotating the travel motor with the track
to be measured jacked up, measure amount
of oil draining from the travel motor and
check travel motor performance.
2. Judge travel motor performance from the
results including travel speed, mistrack and
so on overall.
3. The amount of drain oil from the travel motor 1
will change depending on hydraulic oil tem-
perature.
CAUTION:Prevent personal injury. Always make

sure that the area is clear and that co-workers are out
before starting the measurement.
Also, take care not to fall off the machine while the
measurement.
Preparation:
1. Main hydraulic oil temperature at 50±5 °C T157-05-04-014
(122±41 °F). Rotate the travel motor and warm
inside of the motor.
2
2. Stop the engine. Push air bleed valve (1) on top
of the hydraulic oil tank and release any remain-
ing pressure.
3. Remove drain hose (2) in the travel motor at the

travel motor end. Install plug (ST 6637) to the
removed end. Install the drain hose (3/4-16UN)
to the travel motor.
: 27 mm
: 78 N⋅m (8.0 kgf⋅m, 58 lbf⋅ft)
Preconditions for Measurement:

Work Mode
Digging M178-07-047
Mode
T4-5-29
Measurement:
CAUTION: When working around moving

parts is unavoidable, pay special attention to
ensure that hands, feet, and clothing do not
become entangled. Securely support the
90 to 110°
raised track by using the blocks.
(1) Start the engine. Jack up the track to be

measured.
M104-07-067
(2) Rotate the track to be measured. Start drain
oil measurement when drain oil starts coming Drain Hose
out of the drain hose end.

in both forward and reverse directions, and
seconds.
Evaluation:
Group T4-2.
∗ Conversion of amount of drain oil measured into

the per-minute value
First measure amount of drain oil using a cali- M178-07-047
brated container. Then, convert the measured

drain oil into the per-minute value using the for-
mula below:
∆Q = 60 × q / t
∆Q : Amount of drain oil per minute (L/min)

t : Measured time (seconds)
q : Total amount of drain oil (L)
T4-5-30
MEMO
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
MEMO
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
SECTION 5
TROUBLESHOOTING
CONTENTS
Group 1 Diagnosing Procedure Group 3 Dr. ZX
Introduction ..............................................T5-1-1 Outline .....................................................T5-3-1
Diagnosing Procedure ..............................T5-1-2 Select Controller.......................................T5-3-6
Main Controller .........................................T5-3-7
Group 2 Monitor Unit Main Menu Monitor Display.......................T5-3-8
Outline .....................................................T5-2-1 Special Function .....................................T5-3-14
How to Use Screens...............................T5-2-19 Setting....................................................T5-3-16
Primary Screen ......................................T5-2-29 Adjustment Data List ..............................T5-3-20
Screen Display Attachment Adjustment Data List ............T5-3-24
When An Alarm is Issued ....................T5-2-30 Attachment Setting .................................T5-3-46
Contents of Alarms .................................T5-2-32 Engine Controller....................................T5-3-55
Troubleshooting......................................T5-2-34 Main Menu Monitor Display.....................T5-3-57
Controller Version...................................T5-2-36 Data Upload From ECM..........................T5-3-60
Monitoring ..............................................T5-2-38 Data Download To ECM..........................T5-3-62
Displaying Operating Conditions.............T5-2-41 Write Injection ID Code ..........................T5-3-64
Pump 2 Flow Rate Adjustment ECM Data Display ..................................T5-3-66
(Only Machines Equipped Actuator Test ..........................................T5-3-67
with Optional Parts).............................T5-2-42 Example Of How Engine Speed
Attachment Selection Down & Stop Cylinder Function Used
(Only Machines Equipped On A Four Cylinders Engine) ..............T5-3-70
with Optional Parts).............................T5-2-44 Record Data Display...............................T5-3-71
Time Set.................................................T5-2-48 Password Change ..................................T5-3-72
Fuel Rate Display/No Display .................T5-2-50 ICF Controller .........................................T5-3-73
Back Monitor Settings ............................T5-2-54 Main Menu
Maintenance Settings .............................T5-2-56 Information C/U Various Setup ............T5-3-74
Language Settings .................................T5-2-62 Information C/U: Initialize .......................T5-3-75
Mail (Optional)........................................T5-2-64 Enter Model and Serial No......................T5-3-76
List of Monitor Unit Sitting Function ........T5-2-66 Enter Date and Time ..............................T5-3-77
Control Data: Initialize ............................T5-3-78
Satellite Terminal: Initialize .....................T5-3-79
Satellite Terminal No. Confirmation.........T5-3-80
Communicating State Check...................T5-3-81
Enter Satellite Comm. Start / Stop ..........T5-3-82
Date Download .......................................T5-3-83
1V1T-5-1
Save Data Check ...................................T5-3-84 Group 5 Component Layout
Password Change ..................................T5-3-85 Main Components ....................................T5-5-1
Monitor Controller...................................T5-3-86 Electrical System (Overview) ....................T5-5-4
Monitoring ..............................................T5-3-87 Electrical System (In Cab) ........................T5-5-6
Various Settings .....................................T5-3-91 Electrical System (Rear Tray) ...................T5-5-8
Optional Function Allocation ...................T5-3-92 Electrical System (Switch Panel) ............T5-5-10
Overload Alarm Electrical System (Around Air Cleaner) ... T5-5-11
Enable / Disable Selection ..................T5-3-98 Electrical System (Relays) ......................T5-5-12
Back Monitor Setting ............................ T5-3-100 Engine....................................................T5-5-13
Operating Condition Pump Device ..........................................T5-5-14
Enable / Disable Selection ................ T5-3-104 Swing Device..........................................T5-5-15
Time Setting Function Control Valve ..........................................T5-5-16
Enable / Disable Selection ................ T5-3-106 Signal Control Valve ...............................T5-5-16
Maintenance Setting Maintenance Operation Solenoid Valve Unit ................................T5-5-17
Allow / Not Allow Selection ................ T5-3-108 Travel Device .........................................T5-5-17
Notification Function Layout of Attachment Spec. Parts ..........T-5-5-18
Enable / Disable Selection ................ T5-3-110 Pilot Port (Signal Control Valve)..............T5-5-42
Maintenance Display Item
On/Off Selection ............................... T5-3-112
Fuel Consumption Gauge Display
Enable / Disable Selection ................ T5-3-116
Password Change ................................ T5-3-118
Group 4 e-Shovel
Outline .....................................................T5-4-1
List of Daily Report Data...........................T5-4-2
List of Frequency Distribution Data ...........T5-4-5
List of Total Operating Hours ....................T5-4-6
How to
Download and Upload Data of ICF ........T5-4-8
Various Setup of ICF and
Satellite Communication Terminal
by Using Dr. ZX................................... T5-4-11
List of Fault Code ...................................T5-4-23
Satellite Communication System ............T5-4-24
1V1T-5-2
Group 6 Troubleshooting A ECM, Sensor System
Troubleshooting A Procedure....................T5-6-1 ECM Fault Codes 100, 102, 105,
Fault Code List .........................................T5-6-2 108, 110, 157, 172 ............................T5-6-100
ECM .......................................................T5-6-20 ECM Fault Codes
ICF .........................................................T5-6-44 174, 636, 723, 10001 ........................T5-6-101
Controller Hardware Failure ECM, External Device System
MC Fault Code 11000 to 11002 ...........T5-6-50 ECM Fault Codes 651, 652, 653,
MC Fault Code 11003.............................T5-6-51 654, 655, 656, 1347, 10002...............T5-6-102
MC Fault Code 11004.............................T5-6-52 ECM, Fuel System
CAN Harness Check ..............................T5-6-54 ECM Fault Codes
Engine Failure 157, 633, 1239, 1240 ........................T5-6-103
MC Fault Code 11100..........................T5-6-73 ECM, Engine Protection
MC Fault Code 11101 .............................T5-6-74 ECM Fault Codes 110, 190................T5-6-104
Pump Failure ECM, Engine Protection
MC Fault Code 11200 .........................T5-6-75 ECM Fault Codes 987, 1485 .............T5-6-105
MC Fault Code 11202.............................T5-6-76 ECM, Internal Circuit System
MC Fault Code 11206.............................T5-6-77 ECM Fault Codes 628, 1077, 1079,
MC Fault Code 11208.............................T5-6-78 1080, 10003, 10004, 10005...............T5-6-106
Pilot Failure ECM Fault Codes 10006, 10007, 10008,
MC Fault Code 11301 .........................T5-6-79 10009, 10010, 10011, 10013 .............T5-6-107
MC Fault Code 11302.............................T5-6-80 ECM, Communication System
MC Fault Code 11303.............................T5-6-81 ECM Fault Codes 639 .......................T5-6-108
MC Fault Code 11304.............................T5-6-82 ICF, Satellite Terminal Fault Codes
MC Fault Code 11307.............................T5-6-83 14000 to 14003 .................................T5-6-109
Proportional Solenoid Valve Failure ICF, Satellite Terminal Fault Codes
MC Fault Code 11400 .........................T5-6-84 14006, 14008, 14100 to 14106 .......... T5-6-113
MC Fault Code 11401.............................T5-6-85 Monitor Unit Fault Code 13303 ............. T5-6-115
MC Fault Code 11403.............................T5-6-87 Monitor Unit Fault Code 13306, 13308.. T5-6-117
CAN Data Reception Failure Pilot Shut-Off Lever Alarm ....................T5-6-120
MC Fault Code 11910, 11914, 11920...T5-6-90
CAN Harness Check
MC Fault Code 11910, 11914, 11920...T5-6-92
MC Fault Code 11911, 11918..................T5-6-95
CAN Harness Check
MC Fault Code 11911, 11918 ..............T5-6-96
Other Failures
MC Fault Code 11901 .........................T5-6-99
1V1T-5-3
Group 7 Troubleshooting B
Troubleshooting B Procedure ...................T5-7-1
Relationship between Machine Trouble
Symptoms and Related Parts ................T5-7-2
Correlation between Trouble
Symptoms and Part Failures ...............T5-7-42
Engine System Troubleshooting .............T5-7-58
All Actuator System Troubleshooting ......T5-7-86
Front Attachment System
Troubleshooting ................................ T5-7-100
Swing System Troubleshooting............. T5-7-120
Travel System Troubleshooting ............ T5-7-124
Other System Troubleshooting ............. T5-7-132
Exchange Inspection ............................ T5-7-152
Emergency Boom Lowering
Procedure ......................................... T5-7-155
Attachment Pilot Circuit
Pressure Release Procedure ............ T5-7-156
One Part of Data, Daily Report Data,
Distribution Data and Total Operating hours
is not Recorded................................. T5-7-158
Group 8 Electrical System Inspection

Precautions for Inspection and
Maintenance .........................................T5-8-1
Instructions for Disconnecting
Connectors ...........................................T5-8-3
Fuse Inspection........................................T5-8-4
Fusible Link Inspection .............................T5-8-5
Battery Voltage Check ..............................T5-8-6
Alternator Check ......................................T5-8-7
Continuity Check ......................................T5-8-8
Voltage and Current Measurement .........T5-8-10
Check by False Signal ............................T5-8-17
Test Harness ..........................................T5-8-18
1V1T-5-4
TROUBLESHOOTING / Diagnosing Procedure
INTRODUCTION
Refer to the inspection and troubleshooting proce-
dures after any machine trouble has occurred. The
inspection and troubleshooting procedures are pre-
sented in an orderly fashion in this section to quickly
find the cause of the machine trouble and solution.
The troubleshooting section in this manual consists of

8 groups; Diagnosing Procedure, monitor unit, Dr. ZX,
e-Shovel, Component Layout, Troubleshooting A (base
machine diagnosis by using fault codes), Trouble-
shooting B (base machine diagnosis starting with in-
spection of abnormal operational status) and Electrical
System Inspection.
• Monitor Unit • Troubleshooting A (base machine diagnosis by

Refer to this group as for the display screen and using fault codes)
operating procedures of monitor unit. Refer to these procedures if any fault codes are
displayed when each controller (MC, ECM, ICF
• Dr. ZX and monitor unit) is diagnosed by using Dr. ZX (or
This group contains the operating procedures for the service menu of monitor unit).
Dr. ZX.
• e-Shovel IMPORTANT: ICF receives and retains a record of

This group contains as follows. the electrical signal system mal-
Download data from ICF and Upload function of each controller in the
Procedures when starting satellite communication, form of fault codes by using CAN
when installing the satellite communication con- communication. In addition, ICF
troller and when replacing ICF self-diagnosing function records the
Explanation for the satellite communication sys- electrical signal system malfunction
tem in the form of fault codes
Ex.) Fault Code 11004-2: Failure of CAN Com-
• Component Layout munication
• Troubleshooting B (base machine diagnosis start-

ing with inspection of abnormal operational
status)
Refer to these procedures when no fault codes
are displayed after diagnosing the machine with
Dr. ZX (or the service menu of monitor unit).
Ex.) Although the engine control dial is turned,
engine speed does not change.
• Electrical System Inspection

Refer to this group when required to obtain pre-
cautions and/or information for the electrical sys-
tem inspection.
Ex.) Fuse Check
T5-1-1
DIAGNOSING PROCEDURE
These six basic steps are essential for efficient
troubleshooting:
1. Study the System

Study the machine’s technical manuals. Know the
system and how it works, and what the
construction, functions and specifications of the
system components are.
2. Ask the operator

Before inspecting, get the full story of
malfunctions from the operator below.
T107-07-01-001
(a) How is the machine being used? (Find out if
the machine is being operated correctly)
(b) When was the trouble noticed, and what

types of work the machine doing at that
time?
(c) What are the details of the trouble? Is the

trouble getting worse, or did it appear
suddenly for the first time?
(d) Did the machine have any other troubles

previously? If so, which parts were repaired
before?
3. Inspect the machine

Before starting the troubleshooting procedure,
check the machine’s daily maintenance points, as
shown in the operator's manual. T107-07-01-002
Also, check the electrical system, including the

batteries, as troubles in the electrical system such
as low battery voltage, loose connections and
blown fuses will result in malfunction of the
controllers, causing total operational failure of the
machine.
If troubleshooting is started without checking for
blown fuses, a wrong diagnosis may result,
wasting time. Check for blown fuses before
troubleshooting. Even if a fuse looks normal by
visual inspection, a fine crack is difficult to find.
Always use a tester when checking the fuses.
T107-07-01-003
T5-1-2
4. Operate the machine yourself

Try to identify the trouble by operating the
machine yourself.
If the trouble cannot be confirmed, stop the
engine and obtain further details of the
malfunction from the operator.
Also, check for any incomplete connections of the
wire harnesses correponding to the trouble.
T5-1-3
5. Perform troubleshooting
CAUTION: Do not disconnect harnesses or

hydraulic lines while the engine is running.
The machine may malfunction or pressurized
oil may spout, possibly resulting in personal
injury. Stop the engine before disconnecting
harnesses or hydraulic lines.
Perform diagnosis by connecting Palm to the

machine or by using the service menu of monitor
unit. In case any fault code has been displayed by
diagnosis by using Dr. ZX (the service menu of
monitor unit), check the cause of the trouble by T107-07-01-005
referring to Troubleshooting A in this section. In
case any fault code has been displayed by diag-
nosis by using Dr. ZX (the service menu of moni-
tor unit), write the fault code. Delete the fault code
once and retry self-diagnosis again. If the fault
code is displayed again, check the cause of the
trouble by referring to Troubleshooting A in this
section. After the machine trouble has been cor-
rected, the fault code (displayed by the service
menu of monitor unit) will be deleted. Therefore,
in case the problems which are not easily
re-predicable are encountered, check the fault
code by using Dr. ZX.
In case the fault code is not displayed, check

operating condition of each component by refer- T107-07-01-006
ring to Troubleshooting B in this section and by
using Dr. ZX (the service menu of monitor unit).
NOTE: Note that the fault codes displayed do not

necessarily indicate machine trouble. The
controller stores even temporary electrical
malfunctions, such as a drop in battery
output voltage or disconnections of the
switches, sensors, etc., for inspections.
For this reason, the “RETRIAL” is required
to erase the accumulated fault codes from
the controller memory and to confirm if any
fault codes are indicated after the
T107-07-01-007
“RETRIAL”.
T5-1-4
6. Trace possible causes

Before reaching a conclusion, check the most
likely causes again. Try to identify the actual
cause of the trouble.
Based on your conclusion, make a plan for
appropriate repairs to avoid consequent
malfunctions.
T5-1-5
(Blank)
T5-1-6
TROUBLESHOOTING/ Monitor Unit
OUTLINE
Primary Screen
Machine with Overload Alarm

(Optional) Attached
1 2 3 4 5 6 7 8
22 10
11
12
13
14
15
21 20 19 18 17 16
T1V1-05-01-094
1 - Work Mode Display 7 - Work Mode Display 13 - Fuel Consumption Gauge 18 - Mail Selection (Optional)
2 - Auto-Idle Display 8 - Hour Meter 14 - Clock 19 - *ML Crane Selection (Op-
tional)
3 - *ML Crane Display or 9 - *ML Crane Display (Op- 15 - Back-Screen Selection 20 - Work Mode Selection
Overload Alarm Display tional)
(Optional)
4 - Auxiliary 10 - Fuel Gauge 16 - Menu 21 - Return to Primary Screen
5 - Auxiliary 11 - Mail Display (Optional) 17 - Auxiliary Selection 22 - Coolant Temperature
Gauge
6 - Glow Display 12 - Auxiliary
NOTE: *ML crane display and ML crane selection is only available in Japanese domestic marked.
T5-2-1
• Display of Meters
Work Mode 2
Data to be displayed on each meter from are dis-
played on the monitor unit according to the input
signal from sensor, the signal received by using CAN
and the internal data of monitor unit. 1 3
Items to be displayed
1. Coolant Temperature Gauge (Input signal from the
coolant temperature sensor)
2. Hour Meter (Internal data of the monitor unit)
3. Fuel Consumption Gauge (Input signal from the 4
fuel sensor)
4. Clock (Signal received from ICF by using CAN)
• Work Mode Display

The attachments being used are displayed accord- T1V1-05-01-008
ing to the signals received from MC by using CAN.
Digging Mode
T1V1-05-01-108
Attachment Mode
Breaker
T1V1-05-01-104
Pulverizer
T1V1-05-01-105
Crusher
T1V1-05-01-106
Vibrating Hammer
T1V1-05-01-107
Others
T1V1-05-02-003
NOTE: The items on monitor unit and HITACHI

pattern are same.
Monitor Unit HITACHI pattern
Breaker1 Hydraulic Breaker1
Pulverizer1 Secondary Crusher1
Crusher1 Primary Crusher1
T5-2-2
1 3
• Auto-Idle Display (1)
When the switch is turned ON, the data is displayed.
When the key switch is turned ON with the auto-idle
switch ON, the data blinks for 10 seconds.
T1V1-05-01-008
2
Overload Alarm (2)
T1V1-05-02-002
The system measures the load of suspended load

from the bottom pressure of boom cylinder. When
overload is detected, an alarm is displayed.
(Refer to T5-2-10.)
• Glow Display (3)

While ECM is supplying current to the glow plug, the
date is displayed according to the signal from ECM.
• Fuel Consumption Gauge Display (4)

T1V1-05-01-128
IMPORTANT: The values on fuel gauge are refer-
ences and different from the meas-
ured values.
Fuel consumption is displayed according to the sig-
nal from ECM, which is received through MC by us-
ing CAN bus line.
T5-2-3
• Fuel Gauge
Fuel level is displayed on . Fuel Gauge
Primary Screen T1V1-05-01-008
Fuel Level Primary Screen

Less than 1%
T1V1-05-02-010
1% or more
Less than 3%
T1V1-05-02-012
T5-2-4

3% or more
Less than 5%
T1V1-05-02-014
5% or more
Less than 12%
T1V1-05-02-016
12% or more
Less than 20%
T1V1-05-02-018
20% or more
Less than 30%
T1V1-05-02-020
30% or more
Less than 40%
T1V1-05-02-022
40% or more
Less than 50%
T1V1-05-02-024
T5-2-5

50% or more
Less than 60%
T1V1-05-02-026
60% or more
Less than 70%
T1V1-05-02-028
70% or more
Less than 80%
T1V1-05-02-030
80% or more
Less than 90%
T1V1-05-02-032
90% or more
Less than 100%
T1V1-05-02-034
100% or more
T1V1-05-02-036
T5-2-6
(Blank)
T5-2-7
• Coolant Temperature Gauge
Coolant Temperature Gauge
Temperature of engine coolant is displayed on.
Coolant Temperature Primary Screen

Less than 40°C
T1V1-05-02-038
40°C or more
Less than 45°C
T1V1-05-02-040
T5-2-8

45°C or more
Less than 50°C
T1V1-05-02-042
50°C or more
Less than 60°C
T1V1-05-02-045
60°C or more
Less than 80°C
80°C or more
Less than 96°C
T1V1-05-02-047
96°C or more
Less than 98°C
T1V1-05-02-049
T5-2-9

98°C
T1V1-05-02-051
99°C
T1V1-05-02-053
100°C
T1V1-05-02-054
101°C
T1V1-05-02-056
102°C
T1V1-05-02-058
103°C
T1V1-05-02-060
T5-2-10

104°C
T1V1-05-02-062
105°C or more
Less than 110°C
T1V1-05-02-064
110°C or more
Less than 115°C
T1V1-05-02-066
115°C or more
Less than 120°C
T1V1-05-02-067
120°C or more
T1V1-05-02-068
Overheat SW=ON
T1V1-05-02-068
T5-2-11
• Fuel Sensor Error Display Coolant Temperature Fuel Sensor Error
When the fuel sensor is faulty or if the harness be- Sensor Error Display Display
tween fuel sensor and monitor unit is open circuit,
the data is displayed on the fuel gauge.
• Coolant Temperature Sensor Error Display

When the coolant temperature sensor is faulty, the
data is displayed on the coolant temperature gauge.
• Alarm and Remedy Displays against Alarm

Alarm marks are displayed on bottom of the screen
according to the alarm signals from pilot shut-off T1V1-05-02-005
lever, overheat switch, fuel sensor, hydraulic oil filter

alarm switch (optional), air cleaner restriction switch,
alternator, battery system and ECM and the alarm
signals received by using CAN bus line. The remedy
for each alarm is displayed by key operation.
Alarm Display T1V1-05-01-096
Remedy Display against T1V5-05-01-013
Alarm
T5-2-12
• Troubleshooting
This screen displays the fault codes according to the
signals received from each controller by using CAN.
Fault Code Display T1V5-05-01-097
• Controller Version
This screen displays the version of MC, ICF and
monitor unit.
NOTE: The version of ECM is not displayed.
Controller Version Display T1V5-05-01-122
• Monitoring
This screen displays temperature and pressure data
received from each controller by using CAN.
By key operation, the displayed data is hold.
T1V5-05-01-087
Monitoring Screen
• Operating Conditions
This screen displays machine operating hour, fuel
usage and fuel consumption rate registered by the
monitor unit.
Operating Conditions Screen T1V5-05-01-025
T5-2-13
• Pump 2 Flow Rate Adjustment
(Only machines equipped with optional parts)
When using the attachments, fine adjust flow rate of
pump 2 by keys 1 and 2 operation.
The signals from the monitoring unit are sent to MC
by using CAN.
When breaker 1 or 2 is used, MC adjusts flow rate of
pump 2 while controlling maximum pump 2 flow rate
limit control solenoid valve. When pulverizer 1 or
crusher 1 is used, MC adjusts flow rate of pressure
oil that flows from pump 2 to pulverizer or crusher key 1
while controlling the auxiliary flow rate control sole-
noid valve. (Refer to "Control Systems.") key 2
When using Breaker 1 T1V5-05-01-111

NOTE: When the 2-speed selector circuit is OFF,
flow rate of pump 2 can be adjusted while
controlling the maximum pump 2 flow rate
limit control solenoid valve. When the
2-speed selector circuit is ON, flow rate of
pressure oil that flows from pump 2 to the
attachments can be adjusted while control-
ling the auxiliary flow rate control solenoid
valve.
The table blow is the setting of various
factors at the time of shipment from the key 1
factory.
key 2
T1V5-05-01-024
When using Pulverizer 1
Type of 2-Speed Valve Selector Accumulator Secondary Pump 2 Flow Auxiliary Flow
Attachments Selector Circuit Circuit Circuit Hydraulic Rate Control Rate Control
Relief Selector
Circuit
Breaker 1 OFF to Hydraulic OFF ON ON OFF
Oil Tank
Breaker 2 OFF to Hydraulic ON OFF ON OFF
Oil Tank
Pulverizer 1 ON to Control Valve OFF OFF OFF ON
Crusher 1 ON to Control Valve OFF OFF OFF ON

pattern are same.
T5-2-14
• Attachment Selection
Select digging mode and attachment mode set by Dr.
ZX on this screen.
NOTE: In attachment mode, the following five

modes are set at the time of shipping from
the factory.
1 - Digging
2 - Breaker 1
3 - Breaker 2
4 - Pulverizer 1
1 2 3 4 5
5 - Crusher 1 T1V5-05-01-109
Attachment Selection Screen

pattern are same.
T5-2-15
• Back Monitor Settings
By key operation, image display ON and OFF of
Auto-Control for switching image of the back monitor
while traveling can be set.
T1V5-05-01-173
T5-2-16
• Maintenance Settings
This screen displays the hour meter reading at re-
placement time and the remaining hours until the
next replacement.
As the items to be replaced are displayed in a list,
record performed replacement by selecting an item
from the list.
• Interval ON/OFF Settings

Set change interval for each item to be replaced.
• Items included in Maintenance Settings

Engine Oil Maintenance Setup Screen T1V5-05-01-049
Engine Oil Filter
Hydraulic Oil
Hydraulic Oil Pilot Filter
Hydraulic Oil Full-Flow Filter
Pump Transmission Oil
Travel Device Oil
Swing Device Oil
Swing Bearing Grease
Air Cleaner Filter
Engine/Air Conditioner V-belt
Fuel Filter
Air Conditioner Filter
• Language Settings Interval ON/OFF Setup Screen T1V5-05-01-052
Select a language to be used in screens from among

preset languages, according to work environment.
• Mail
(Optional Function)
Send requests such as general, fuel replenishment,
service maintenance and forwarding requests in the
mail switch screen.
Contents of mails are registered in ICF, and are sent
to the central server by a satellite terminal.
Language Setup Screen T1V1-05-01-137
Mail Switch Screen T1V5-05-01-037
T5-2-17
• Overload Alarm
Alarm
IMPORTANT: When using overload alarm, make

overload alarm available by using Dr.
ZX.
The system measures load of the suspended load

from bottom pressure of the boom cylinder. An alarm
message is displayed and a buzzer is rung, if over-
load is detected.
1. If load of the suspended load becomes over-

loaded, the boom bottom pressure sensor (op-
tional) sends a signal to MC. T1V1-05-01-128
Primary Screen
2. If the overload alarm ON/OFF switch (optional) is Overload Alarm ON/OFF Switch (Op-
turned ON, the monitor unit displays an alarm tional)
message and rings a buzzer according to the
signal from MC by using CAN.
3. If overload of the suspended load is dissolved, the

alarm message disappears and the buzzer stops
ringing.
NOTE: Even if the work is done while displaying a

screen except the primary screen, when an
overload condition is reached, the screen of
monitor unit is switched to the primary
screen, an alarm message is displayed, T1V1-05-02-004
and a buzzer is rung.

Even after the overload alarm is dissolved,
the monitor unit keeps on displaying the
primary screen without returning to the
screen while the work is done.
T5-2-18
HOW TO USE SCREENS
Displaying Primary Screen
IMPORTANT: Start the engine after the primary

screen is displayed.
When the key switch is turned to the ON position, the

starting screen appears for about two seconds and the
primary screen appears.
Key Switch: ON T1V1-05-01-115
IMPORTANT: After the engine starts and the al-

ternator starts generating power, al-
ternator alarm is displayed on the
primary screen.
T1V1-05-01-117
Alternator Alarm
T5-2-19
Displaying Primary Screen by Password Input
(Optional)
IMPORTANT: Before performing this operation,

make the password function avail-
able by using Dr. ZX.
Starting Screen T1V1-05-01-115
1. When the key switch is turned to the ON position,

the starting screen appears and the password
input screen appears.
T1V5-05-01-093
Password Input Screen
2. Input a password by using the keys located under
the screen. If pushing the confirm key, the monitor
unit matches the input password to the registered
one. If they match, the primary screen appears.
NOTE: When inputting the password again, the

entered characters can be erased by
pushing the erase key.
T1V5-05-01-002
Confirm Key Erase Key
T5-2-20
(Blank)
T5-2-21
In Case of Inputting an Incorrect Password
1. If inputting an incorrect password, the message

"password is incorrect." appears by pushing the
confirm key.
T1V5-05-01-093
Password Input Screen
T1V5-05-01-002
2. Return to the password input screen by pushing

the back key.
NOTE: When inputting the password again, the

entered characters can be erased by
pushing the erase key.
T1V5-05-01-004
Back Key
T1V5-05-01-093
T5-2-22
3. If inputting an incorrect password three times, a
screen appears informing that the security lock
has been applied, and a buzzer rings. While the
key switch is turned to the ON position, the buzzer
does not stop ringing. When the key switch is
turned to the OFF position, the buzzer rings for
thirty seconds.
T1V5-05-01-005
Security Lock Screen
4. After thirty seconds, if the key switch is turned to
the ON position, the starting screen appears and
the password input screen appears again. Then a
password can be input again. If inputting an in-
correct password even once this time, the security
lock screen appears again and a buzzer rings.
While the key switch is turned to the ON position,
the buzzer does not stop ringing. When the key
switch is turned to the OFF position, the buzzer
rings for thirty seconds.
Starting Screen T1V1-05-01-115
5. After the buzzer stops ringing, a password can be

input again. Turn the key switch to the ON position
and input a password after the password input
screen appears. (Refer to T5-2-20).
6. If inputting an incorrect password again, the secu-

rity lock screen appears again and a buzzer rings.
While the key switch is turned to the ON position,
the buzzer does not stop ringing. When the key
switch is turned to the OFF position, the buzzer
rings for thirty seconds.
Password Input Screen T1V5-05-01-093
T5-2-23
Extending Password Duration Time
IMPORTANT: This operation is applicable only to

those machines that display the
primary screen based upon pass-
word input.
By using the password duration screen, password du-

ration time can be set. When restarting the machine, a
password need not be input within that timeframe.
1. When turn the key switch to the OFF position,
the monitor unit displays the password duration
screen for ten seconds. Ｋey 1 Ｋey 2 Ｋey 3 Ｋey 4 Ｋey 5 T1V1-05-01-012
Password Duration Screen (Key Switch: OFF)
2. While the password duration screen is still dis-

played, push a relevant key, and password dura-
tion time is set. Duration time assigned to each
key is as follows:
key 1: 0 minute
key 2: 30 minutes
key 3: 60 minutes
key 4: 90 minutes
key 5: 120 minutes
NOTE: If password duration time is not set ex-

plicitly, 0 minute on duration time is as-
sumed.
Key Switch: ON T1V1-05-01-115
3. If turning the key switch to the ON position within

password duration time, the monitor unit displays
the primary screen after the starting screen.
T5-2-24
(Blank)
T5-2-25
Password Change (Optional)
1. After the primary screen is displayed, push the

menu key in order to display the main menu.
Menu Key
T1V5-05-01-123
Primary Screen
2. Select password change from main menu by us-
ing keys1 and 2. Push the confirm key. Then, the
password change screen appears.
T1V5-05-01-129
Key 1 Key 2 Confirm Key
T1V5-05-01-041
Registered Password
3. Input the registered password and push the con-

firm key.
4. If inputting the password again, the entered

characters can be erased by pushing the erase
key.
T1V5-05-01-042
T5-2-26
NOTE: If inputting an incorrect password after

pushing the confirm key, the message
"Password is incorrect." appears.
Push the back key and go back to the pre-
vious screen, Input the password again.
T1V5-05-01-044
Back Key
5. The message "Enter password to be registered."

appears. Then, input a new password with three
or four digits and push the confirm key.
6. If inputting the password again, push the erase

key.
T1V5-05-01-130
A New Password
T1V5-05-01-131
T5-2-27
7. The message "Re-enter password." appears.
Then, input a new password again and push the
confirm key.
8. If inputting the password again, push the erase

key in order to erase the entered characters.
T1V5-05-01-132
Confirm Key Erase Key T1V5-05-01-133
9. The message "New password has been regis-

tered." appears. This completes the password
change process.
T1V5-05-01-043
Key 6
10. Push key 6 and the primary screen appears.
T1V1-05-01-123
Primary Screen
T5-2-28
PRIMARY SCREEN
Machine with Overload Alarm
(Optional) Attached
1 2 3 4 5 6 7 8
22 10
11
12
13
14
15
21 20 19 18 17 16
T1V1-05-01-094
1 - Work Mode Display 7 - Work Mode Display 13 - Fuel Consumption Gauge 18 - Mail Selection (Optional)
2 - Auto-Idle Display 8 - Hour Meter 14 - Clock 19 - *ML Crane Selection (Op-
tional)
3 - *ML Crane Display or 9 - *ML Crane Display (Op- 15 - Screen Selection 20 - Work Mode Selection
Overload Alarm Display tional)
(Optional)
4 - Auxiliary 10 - Fuel Gauge 16 - Menu 21 - Return to Primary Screen
5 - Auxiliary 11 - Mail Display (Optional) 17 - Auxiliary Selection 22 - Coolant Temperature
Gauge
6 - Glow Display 12 - Auxiliary
NOTE: *ML crane display and ML crane selection is only available in Japanese domestic marked.
T5-2-29
SCREEN DISPLAY WHEN AN ALARM IS
ISSUED
When an alarm is issued, the alarm marks are dis-
played at the bottom of screen.
• When the number of alarms is two or less
T1V1-05-01-095
• When the number of alarms is three or more
T1V1-05-01-096
T5-2-30
When an alarm is issued, if the key under a relevant
alarm mark is pushed, the remedy against the alarm is
displayed.
Push a Relevant Key T1V1-05-01-095
T1V5-05-01-013
T5-2-31
CONTENTS OF ALARMS
Display Contents of Alarms Remedy

Overheat Alarm Temperature of engine coolant is going up abnormally higher.
Stop the work and turn the engine into low idle in order to lower
the coolant temperature.
M178-01-036
Engine Warning Alarm Failure of the engine or its related parts.

Please contact our authorized distributor or dealer.
M183-01-080
Engine Oil Pressure Alarm Pressure of engine lubricant oil is decreasing.

Stop the engine immediately and inspect the engine oil system
and oil volume of the engine.
M178-01-037
Alternator Alarm The electronic system is faulty.

Inspect the alternator and battery system.
M183-01-071
Fuel Level Alarm Volume of remaining oil is becoming less.

Refuel oil earlier.
M178-01-034
Hydraulic Oil Filter Alarm The hydraulic oil filter is clogged.

Clean or replace the hydraulic oil filter.
M1CC-01-039
Air Filter Restriction Alarm The air filter is clogged.

Clean or replace the air filter.
M183-01-067
Work Mode Alarm The network system is abnormal.

T1V1-05-01-102
Pilot Shut-Off Lever Alarm The pilot shut-off lever system is abnormal.
T1V1-05-01-103
T5-2-32
(Blank)
T5-2-33
TROUBLESHOOTING
1. Displaying Service Menu
Turn the key switch to the ON position while
pushing the key at upper right corner of the
monitor unit. Therefore, service menu is added to
main menu.
T1V1-05-01-115
Turn key switch ON while pushing the key
2. When the primary screen appears, push the menu

key and display main menu.
Menu Key
3. Select service menu from main menu by using

keys 1 and 2. Push the confirm key. Then, the
service menu screen appears.
NOTE: When pushing the back key, return to the

previous screen.
T1V5-05-01-114
Key 1 Key 2 Confirm Key Back Key
Back Key T1V5-05-01-083
T5-2-34
4. Select troubleshooting by using keys 1 and 2.
Push the confirm key. Then, the troubleshooting
screen appears.
5. Results of trouble analyses for each controller are

displayed on the screen.
6. Select Abnormal of a faulty controller by using

keys 1 and 2. Push the confirm key. Then, fault
code screen appears.
For details of trouble analyses, refer to "Trouble-
shooting A."
Key 1 Key 2 Confirm Key Back Key T1V5-05-01-083
IMPORTANT: Up to twenty fault codes can be dis-
played. But, one screen can contain A figure enclosed in ( ) indicates the number of failure codes.
only ten fault codes maximum.
If the screen is fully filled with ten
items, push key 1 and check other
fault codes on the next page.
When returning to the previous page,
push key 2.

previous screen.
7. Push key 6, and the primary screen appears.
Key 1 Key 6 Key 2 Back Key T1V5-05-01-097
T5-2-35
CONTROLLER VERSION
pushing the key at upper right corner of the moni-
tor unit. Therefore, service menu is added to main
menu.
T1V1-05-01-115
Turn the key switch ON while pushing the key
2. When the primary screen appeared, push the

menu key to display main menu.
Menu Key

NOTE: When pushing the back key, return back to

the previous screen.
T1V5-05-01-114
Back Key T1V5-05-01-083
T5-2-36
4. Select controller version by using keys 1 and 2.
Push the confirm key. Then, the controller version
screen appears.
NOTE: The version of ECM is not displayed.

previous screen.
T1V5-05-01-083
T1V5-05-01-122
Key 6 Back Key
T5-2-37
MONITORING
pushing the key at upper right corner of the moni-
tor unit. Therefore, service menu is added to main
menu.
T1V1-05-01-115
Turn the key switch ON while pushing the key
2. When the primary screen appeared, push the

menu key and display main menu.
Menu Key


previous screen.
T1V5-05-01-114
Back Key T1V5-05-01-083
T5-2-38
4. Select monitoring by using keys 1 and 2. Push the
confirm key. Then, the monitoring screen appears.
For items to be monitored, refer to the next page.
T1V5-05-01-083
5. Select an item to be monitored by using keys 1 Key 1 Key 2 Confirm Key
and 2. Push the confirm key. Then, the selected
item is brought up to the top.
6. Push key 3, and the displayed data are put on

hold.
Push key 3 again, and the records are updated
with the displayed data.
7. The monitoring item order is reset to the initial

state by pushing key 4.
When key 4 is pushed and a confirmation mes-
sage appears, push the confirm key. Back Key
T1V5-05-01-087
Key 1 Key 2 Key 3 Key 4 Confirm Key
previous screen.
Back Key
8. Push key 6, and the primary screen appears. Key 6 Confirm Key T1V5-05-01-088
T5-2-39
A List of Items to be Monitored
Items Units
Engine Torque %
Coolant Temperature (E) °C
Fuel Temperature °C
Engine Oil Pressure kPa
Atmospheric Pressure kPa
Intake Air Temperature °C
Boost Pressure kPa
Boost Temperature °C
Coolant Temperature (M) °C
-1
Target Engine Speed min
-1
Actual Engine Speed min
Pump 1 Delivery Pressure MPa
Pump 1 Pump Control Pressure MPa
Pump 1 Target Flow Rate L/min
Pump 2 Delivery Pressure MPa
Pump 2 Pump Control Pressure MPa
Pump 2 Target Flow Rate L/min
Front Attachment Control Pilot MPa
Pressure
Boom Raise Control Pilot Pres- MPa
sure
Arm Roll-In Pilot Pressure MPa
Swing Control Pilot Pressure MPa
Travel Control Pilot Pressure MPa
Attachment Control Pilot Pres- MPa
sure
EC Dial Angle V
Hydraulic Oil Temperature °C
Pump Torque Proportional Valve MPa
Digging Regenerative Valve MPa
Arm Regenerative Valve MPa
Travel Mode Control Pressure MPa
Power Digging Control Pressure MPa
Power Mode -
Travel Mode Switch -
Power Digging Switch -
Radio Signal Strength -
T5-2-40
DISPLAYING OPERATING CONDITIONS
2. Select operating conditions from main menu by

using keys 1 and 2. Push the confirm key. Then,
the operating conditions screen appears.
3. Push the reset key, and a screen appears to con-

firm if it's OK to reset data.
If it’s OK to reset data, push the confirm key. Menu Key
T1V1-05-01-123
Primary Screen
previous screen.
IMPORTANT: Total fuel consumption and fuel

consumption rate depend on the
operating environment and the op-
eration method of machine.
The values shown on the screen are
just for reference.
There could arise ± 20% of differ-
ences between actual fuel consump-
tion and fuel consumption which is
displayed by the monitor unit.
T1V5-05-01-019
T1V5-05-01-025
Reset Key Back Key
Back Key
T1V5-05-01-026
Key 6 Confirm Key
T5-2-41
PUMP 2 FLOW RATE ADJUSTMENT
(Only Machines Equipped with Optional
Parts)
IMPORTANT: This operation is effective when at-
tachments are used.

2. Select attachment adjustment from main menu by

using keys 1 and 2. Push the confirm key. Then, Menu Key
the attachment adjustment screen appears.
T1V1-05-01-123
Primary Screen
3. Push key 2. Then, the attachment adjustment
screen for currently installed attachments ap-
pears.
T1V5-05-01-019
4. Adjust flow rate of pump 2 by using keys 1 and 2.

When breaker 1 or breaker 2 is used, pushing key
1 will decrease flow rate of pump 2 and pushing
key 2 will increase respectively.
T1V5-05-01-111
Key 1 Key 2 Back Key
When using the pulverizer or crusher is used,

pushing key 1 will increase flow rate of boom raise,
arm roll-out, swing or travel circuit sides.
Pushing key 2 will increase flow rate of attach-
ment side.

previous screen.
T1V5-05-01-024
Key 1 Key 6 Key 2 Back Key
T5-2-42
(Blank)
T5-2-43
ATTACHMENT SELECTION
(Only Machines Equipped with Optional
Parts)
IMPORTANT: Select the attachments from the
work mode screen.
In order to display the work mode
screen, push key F1 after primary
screen appears, or select from main
menu.
Selecting Attachment by Using Key F1
1. When the primary screen appears, push key F1 Key F1 T1V1-05-01-123

Primary Screen
and display the work mode screen.
2. Push a relevant key under an attachment mark to

be used in order to select the attachment.
(In the right example, Crusher 1 is selected.)
NOTE: When selecting Digging, return to the pri-

mary screen.
3. On the attachment specification screen, confirm if

specification of the installed attachment agrees
with that displayed on the screen. Digging
Back Key
Select Crusher Work Mode Screen T1V5-05-01-109
previous screen. 1
4. Push confirm the key, and the primary screen

appears.
Back Key
Confirm
Key
T1V5-05-01-028
Attachment Specification Screen
T5-2-44
Selecting Attachment from Main Menu

2. Select work mode from main menu by using keys

1 and 2. Push the confirm key. Then, the work
mode screen appears.
3. Push the relevant key under an attachment mark

to be used in order to select the attachment.
(In the right example, Crusher 1 is selected.) Menu Key
T1V1-05-01-123
NOTE: When selecting digging, return to main Primary Screen
menu.
4. On the attachment specification screen, confirm if

specification of the installed attachment agrees
with that displayed on the screen.
If they do not match, perform the setting of at-
tachment by using Dr. ZX.
For details of the attachment specification screen,
refer to T5-2-46 and 47.

previous screen. Back Key
T1V5-05-01-019
5. Push the confirm key, and the primary screen
appears.
Digging
Back Key
Select Crusher 1 Work Mode Screen T1V5-05-01-109
Back Key
Confirm
Key
Attachment Specification Screen T1V5-05-01-028
T5-2-45
Attachment Specification Screen
Maximum Pump 2 Flow Rate
Maximum Engine Speed
Accumulator Control Solenoid Valve:

OFF
Secondary Hydraulic Relief Selector

Control Solenoid Valve: ON
Selector Valve Control Solenoid Valve: ON

The selector valve is connected to the
hydraulic oil tank.
Auxiliary Flow Combining Solenoid

Valve: OFF
T1V5-05-01-001

ON

Control Solenoid Valve: OFF
Selector Valve Control Solenoid Valve: ON
The selector valve is connected to the
hydraulic oil tank.
Auxiliary Flow Combining Solenoid

Valve: OFF
T1V5-05-01-006
T5-2-46
Maximum Pump 1 and 2 Flow Rate

OFF
Selector Valve Control Solenoid Valve: OFF

The selector valve is connected to the control
valve.
Auxiliary Flow Combining Solenoid Valve:

ON
T1V5-05-01-011
Maximum Pump 1 and 2 Flow Rate

OFF
Selector Valve Control Solenoid Valve: OFF

The selector valve is connected to the control
valve.
Auxiliary Flow Combining Solenoid Valve:

ON
T1V5-05-01-028
T5-2-47
TIME SETTING
Menu Key
T1V1-05-01-123
Primary Screen
2. Select time set from main menu by using keys 1
and 2. Push the confirm key. Then, the time set
screen appears.
Back Key
T1V5-05-01-019
3. On the time set screen, select the items to be set

(Year, Month, Day and Time) by using keys 1 and
2 and set the figures by using keys 3 and 4. Move the
item to
4. By using key 2, move the item to . Push the this icon
confirm key. Then, system time is updated with
the values specified on the screen.

previous screen.
Back Key
5. Push key 6, and return to the primary screen. T1V5-05-01-021
Key 1 Key 2 Key 3 Key 4 Confirm Key
Back Key
Key 6 T1V5-05-01-022
T5-2-48
(Blank)
T5-2-49
FUEL RATE DISPLAY/NO DISPLAY
IMPORTANT: The values displayed on the fuel
gauge are just for reference and dif-
ferent from actual values.
Fuel Rate Display

Menu Key
T1V1-05-01-123
Primary Screen
2. Select fuel rate display/no display from main

menu by using keys 1 and 2. Push the confirm key.
Then, the fuel rate display/no display screen ap-
pears.
T1V5-05-01-118
3. Push the confirm key, and fuel rate display is set

to ON.

previous screen. Back Key
T1V5-05-01-164
Confirm Key
Back Key
T1V5-05-01-119
T5-2-50
4. Push key 6, and the fuel gauge is added to the
primary screen.
Key 6 T1V5-05-01-119
T1V1-05-01-007
Fuel Gauge
T5-2-51
Fuel Rate No Display

Fuel
Gauge
Menu Key
T1V1-05-01-007
Primary Screen
2. Select fuel rate display/no display from main
menu by using keys 1 and 2. Push the confirm key.
Then, the fuel rate display/no display screen ap-
pears.
3. Push the confirm key, and fuel rate display is set

to OFF.

previous screen.
Back Key
Confirm Key T1V5-05-01-119
Back Key
T1V5-05-01-164
T5-2-52
4. Push key 6, and return to the primary screen.
Key 6
T1V5-05-01-164
T1V1-05-01-123
Primary Screen
T5-2-53
BACK MONITOR SETTINGS
IMPORTANT: Image displayed on the back monitor
is of auxiliary nature at best. When
the machine is operated pay thor-
ough attention to surrounding situa-
tion.
Auto-Control: ON
Image on the monitor unit when traveling is automati-

cally switched to that of the back monitor.
Menu Key
1. When the primary screen appears, push the menu Primary Screen T1V1-05-01-123
2. Select back monitor settings from main menu by

the back monitor settings screen appears.
Back Key
T1V5-05-01-114
3. Push the confirm key. Then, auto-control is set to

ON.

primary screen.
5. If travel operation is done, backward image is

displayed on the screen of monitor unit.
Back Key
Key 1 Key 2 Confirm Key T1V5-05-01-173
Back Key
Key 6
T1V5-05-01-174
T5-2-54
Auto-Control: OFF
Set automatic switching function of images between

monitor unit and back monitor when traveling to OFF.

Menu Key
T1V1-05-01-123
Primary Screen
2. Select back monitor settings from main menu by

the back monitor settings screen appears.
T1V5-05-01-118
3. Push the confirm key. Then, auto-control is set to

OFF.

previous screen.
Confirm Key Back Key T1V5-05-01-174
Back Key
Key 6
T1V5-05-01-173
T5-2-55
MAINTENANCE SETTINGS
Menu Key
T1V1-05-01-123
Primary Screen
2. Select maintenance settings from main menu by
the maintenance settings screen appears.
T1V5-05-01-019
3. Select an item to be set from among the list of

maintenance settings screen by using keys 1 and
2. Push the confirm key. Then, the Interval
ON/OFF setup screen appears.
(In the right example, Engine Oil is selected.)
T1V5-05-01-049
T5-2-56
Maintenance Information Display ON/OFF
Example: Maintenance Information Display OFF→ON
ON: When time comes to change, a information

message is displayed on the screen.
OFF: No information message is displayed.
1. Select maintenance information display by using

Key 1
keys 1 and 2. Confirm
Key
Key 2
2. Push the confirm key and select ON.
Key 6
Interval ON/OFF Setup Screen T1V5-05-01-052

3. In order to complete setting, push key 6. Then, the
primary screen appears.
Menu Key
T1V1-05-01-123
Primary Screen
T5-2-57
Change Interval Settings
IMPORTANT: Change interval can only be set

when maintenance information dis-
play is set to ON.
1. Select change interval by using keys 1 and 2.
2. Set time for change interval by using keys 3 and 4. Key 1
3. Select remaining hours by using keys 1 and 2 and

push the confirm key.
Key 2 Key 3 Key 4 T1V5-05-01-052
4. The message "Adjust remaining hours to new
change interval. OK?" appears. Then, push the Interval ON/OFF Setup Screen
confirm key.
Key 1
T1V5-05-01-138
Key 2 Confirm Key
Key 6 Confirm Key T1V5-05-01-139
Menu Key
T5-2-58
Resetting Data
If data is reset, push key 5 on the Interval ON/OFF

setup screen.
The message "Reset Data. OK?" appears. Then,
The value of remaining hours is reset to that of
change interval. The previous change date/hour is
updated with current date and time.
Key 5
Interval ON/OFF Setup Screen T1V5-05-01-052
Confirm Key T1V5-05-01-140
T5-2-59
Screen Display when Maintenance Information
Display is ON
• When only one item is displayed

1. If turning the key switch to the ON position, the
starting screen appears. Then, the maintenance
information display screen for the item whose
change interval has expired appears for ten sec-
onds. Finally the primary screen appears.
(In the right example, Hydraulic Oil is displayed.)
NOTE: As for a machine which the primary screen

is displayed according to a password on, T1V1-05-01-115
Starting Screen
the maintenance information display screen
for the item whose change interval has ex-
pired appears for ten seconds, after the
password is input successfully and the con-
firm key is pushed. And then the primary
screen appears.
2. If data is rest, push the reset key while the main-

tenance information display screen is displayed. Back Key
The value of remaining hours is reset to that of Reset Key
updated with current date and time. T1V5-05-01-170
Maintenance Information Display Screen
NOTE: When pushing the back key while the

maintenance information display screen is
displayed, return to the primary screen.
NOTE: When pushing the back key while reset

screen is displayed, return to the mainte-
nance information display screen.
Back Key
Confirm Key
T1V5-05-01-171
Reset Screen
T1V1-05-01-123
Primary Screen
T5-2-60
• When more than two items are displayed
1. If turning the key switch to the ON position, the
starting screen appears. Then, the scheduled
maintenance screen for the items whose change
interval has expired appears for ten seconds. Fi-
nally the primary screen appears.
NOTE: As for a machine which the primary screen

is displayed according to a password on,
the scheduled maintenance screen for the
items whose change interval has expired
appears for ten seconds, after the pass-
word is input successfully and the confirm T1V1-05-01-115
Starting Screen
key is pushed. And then the primary screen
appears.
2. If data is reset, while the scheduled maintenance

screen is displayed, select desired item by using
maintenance information display screen for the
selected item appears.
(In the right example, Hydraulic Oil is selected.) Key 1 Back Key
NOTE: When pushing the back key while the

scheduled maintenance screen is displayed, Key 2
Confirm
the primary screen appears. Key
T1V5-05-01-169
Scheduled Maintenance Screen
3. Push the reset key while the maintenance infor-
mation display screen is displayed.
The value of remaining hours is reset to that of
updated with current date and time.
NOTE: When pushing the back key while the Back Key
maintenance information display screen is
displayed, return to the scheduled mainte-
nance screen. Reset Key
NOTE: When pushing the back key while the reset

Maintenance Information Display Screen TCHB-05-02-011
screen is displayed, return to the mainte-
nance information display screen.
Back Key
T1V5-05-01-171
Reset Screen
T5-2-61
LANGUAGE SETTINGS
2. Select language from main menu by using keys 1

and 2. Push the confirm key. Then, the language
settings screen appears.
3. Select a desired language by using keys 1 and 2.

Push the confirm key.
NOTE: Languages to be displayed on the screen Menu Key

of monitor unit have been selected from Primary Screen T1V1-05-01-123
twelve languages, namely display lan-

guages 1 or 2, at the time of shipping from
the factory.
(Refer to the next page.)

previous screen.
T1V5-05-01-114
Back Key
T1V1-05-01-137
Key 1 Key 6 Key 2 Confirm Key
T5-2-62
Lists of Display Languages
Display Languages 1
Language Screen Display
Japanese
T1V1-05-01-141
English
T1V1-05-01-142
Chinese
T1V1-05-01-143
Taiwanese
T1V1-05-01-144
Korean
T1V1-05-01-145
Indonesian
T1V1-05-01-146
Thai
T1V1-05-01-147
Vietnamese
T1V1-05-01-148
Myanmarese
T1V1-05-01-149
Arabic
T1V1-05-01-150
Persian
T1V1-05-01-151
Turkish
T1V1-05-01-152
Display Languages 2
Language Screen Display
English
T1V1-05-01-142
Spanish
T1V1-05-01-153
Italian
T1V1-05-01-154
French
T1V1-05-01-155
German
T1V1-05-01-156
Netherlandish
T1V1-05-01-157
Russian
T1V1-05-01-158
Portugese
T1V1-05-01-159
Finlandish
T1V1-05-01-160
Swedish
T1V1-05-01-161
Norwegean
T1V1-05-01-162
Danish
T1V1-05-01-163
T5-2-63
MAIL
(Optional)
IMPORTANT: This function is available only to a
machine equipped with a satellite
terminal.
When using the mail function, make
the mail function available by using
Dr. ZX.
1. When the primary screen appears, push key F3

and display the mail screen.
Key F3 Primary Screen T1V1-05-01-123
2. If pushing a relevant request key, mail information
is sent to ICF.
1 - General Request
2 - Fuel Replenishment Request
3 - Service Maintenance Request
4 - Forwarding Request
3. While mail information is sent to ICF, the message

"Mail is being delivered." is displayed on the
screen.
4. When ICF completes receives mail information,

the message "Mail delivery successful." is dis-
played on the screen. T1V5-05-01-037
When pushing the back key, return to the mail 1 2 3 Mail Screen 4
screen.
5. Then, a mail is sent from the satellite terminal to

the central server via the satellite.
NOTE: Depending on machine operating envi-

ronment or position of the satellite on its
orbit, the mail may not be sent.
T1V5-05-01-038
Back Key
T1V5-05-01-039
T5-2-64
NOTE: When ICF could not receive the mail, the

message "Mail delivery failed." is displayed
on the screen.
T1V5-05-01-040
T5-2-65
LIST OF MONITOR UNIT SETTING FUNC-
TION
○: with setting function
×: without setting function
Setting Function
Factory
Function Item Monitor
Dr. ZX Setting
Unit
Alarm The alarm which the trouble occurs on is checked. ○ ○(Trouble shooting) -
Security Password function is used/ is not used. × ○(Security) Not used
The password is changed. ○ × 0000
The password is changed/ is not changed by the monitor. × ○(Security) Changed
Max.:
The max. digit number of password is changed. × ○(Security)
4 digits
The password is checked. × ○(Security) -
Extension function is used/ is not used. × ○(Security) Used
Extension time is selected. ○ × -
Time Setting Time is is changed/ is not changed by the monitor. × ○(Monitor Controller) Changed
Time is is changed. ○ ○(ICF) -
Operating Machine operating condition is displayed/ is not displayed
× ○(Monitor Controller) Displayed
Condition on the main menu.
Machine operating condition is reset. ○ × -
Maintenance Maintenace setting is operated/ is not operated. × ○(Monitor Controller) Operated
Setting Engine oil is displayed/ is not displayed. × ○(Monitor Controller) Displayed
Information display of engine oil is turned ON/OFF. ○ ○(Monitor Controller) OFF
Replacement interval of engine oil is changed. ○ × 500 hours
The engine oil replacement switch is pushed. ○ × -
Date/ the hourmeter when engine oil was replaced last
○ × -
time are checked.
The engine oil filter is displayed/ is not displayed. × ○(Monitor Controller) Displayed
Information display of engine oil filter is turned ON/OFF. ○ ○(Monitor Controller) OFF
Replacement interval of engine oil filter is changed. ○ × 500 hours
The engine oil filter replacement switch is pushed. ○ × -
Date/ the hourmeter when engine oil filter was replaced
○ × -
last time are checked.
Hydraulic oil is displayed/ is not displayed. × ○(Monitor Controller) Displayed
Information display of hydraulic oil is turned ON/OFF. ○ ○(Monitor Controller) OFF
Replacement interval of hydraulic oil is changed. × × 5000 hours
The hydraulic oil replacement switch is pushed. ○ × -
Date/ the hourmeter when hydraulic oil was replaced last
○ × -
time are checked.
T5-2-66
Setting Function
Factory Set-
Dr. ZX ting
Unit
Maintenance Hydraulic oil pilot fileter is displayed/ is not displayed. × ○(Monitor Controller) Displayed
Setting
Information display of hydraulic oil pilot filter is turned
○ ○(Monitor Controller) OFF
ON/OFF.
Replacement interval of hydraulic oil pilot filter is
× × 1000 hours
changed.
The hydraulic oil pilot filter replacement switch is
○ × -
pushed.
Date/ the hourmeter when hydraulic oil pilot filter was
○ × -
replaced last time are checked.
Hydraulic oil full-flow fileter is displayed/ is not displayed. × ○(Monitor Controller) Displayed
Information display of hydraulic oil full-flow filter is turned
ON/OFF.
Replacement interval of hydraulic oil full-flow filter is
× × 1000 hours
changed.
The hydraulic oil full-flow filter replacement switch is
○ × -
pushed.
Date/ the hourmeter when hydraulic oil full-flow filter was
○ × -
Pump transmission oil is displayed/ is not displayed. × ○(Monitor Controller) Displayed
Information display of pump transmission oil is turned
ON/OFF.
Replacement interval of pump transmission oil is
× × 1000 hours
changed.
The pump transmission oil replacement switch is
○ × -
pushed.
Date/ the hourmeter when pump transmission oil was
○ × -
Travel device oil is displayed/ is not displayed. × ○(Monitor Controller) Displayed
Information display of travel device oil is turned ON/OFF. ○ ○(Monitor Controller) OFF
Replacement interval of travel device oil is changed. × × 2000 hours
The travel device oil replacement switch is pushed. ○ × -
Date/ the hourmeter when travel device oil was replaced
○ × -
Swing device oil is displayed/ is not displayed. × ○(Monitor Controller) Displayed
Information display of swing device oil is turned
ON/OFF.
Replacement interval of swing device oil is changed. × × 1000 hours
The swing device oil replacement switch is pushed. ○ × -
Date/ the hourmeter when swing device oil was replaced
○ × -
Swing bearing lubrication is displayed/ is not displayed. × ○(Monitor Controller) Displayed
Information display of swing bearing lubrication is turned
ON/OFF.
T5-2-67
Setting Function
Factory Set-
Dr. ZX ting
Unit
Maintenance Replacement interval of swing bearing lubrication is
× × 500 hours
Setting changed.
The swing bearing lubrication replacement switch is
○ × -
pushed.
Date/ the hour meter when swing bearing lubrication
○ × -
was replaced last time are checked.
The air cleaner filter is displayed/ is not displayed. × ○(Monitor Controller) Displayed
Information display of air cleaner filter is turned ON/OFF. ○ ○(Monitor Controller) OFF
Replacement interval of air cleaner filter is changed. × × 1500 hours
The air cleaner filter replacement switch is pushed. ○ × -
Date/ the hourmeter when air cleaner filter was replaced
○ × -
The engine/ air conditioner V-belt is displayed/ is not
displayed.
Information display of engine/ air conditioner V-belt is
turned ON/OFF.
Replacement interval of engine/ air conditioner V-belt is
× × 1000 hours
changed.
The engine/ air conditioner V-belt replacement switch is
○ × -
pushed.
Date/ the hourmeter when engine/ air conditioner V-belt
○ × -
was replaced last time are checked.
The fuel filter is displayed/ is not displayed. × ○(Monitor Controller) Displayed
Information display of fuel filter is turned ON/OFF. ○ ○(Monitor Controller) OFF
Replacement interval of fuel filter is changed. × × 500 hours
The fuel filter replacement switch is pushed. ○ × -
Date/ the hourmeter when fuel filter was replaced last
○ × -
time are checked.
The air conditioner filter is displayed/ is not displayed. × ○(Monitor Controller) Displayed
Information display of air conditioner filter is turned
ON/OFF.
Replacement interval of air conditioner filter is changed. × × 3000 hours
The air conditioner filter replacement switch is pushed. ○ × -
Date/ the hourmeter when air conditioner filter was re-
○ × -
placed last time are checked.
The user setting (TRIP1) is displayed/ is not displayed. × × Displayed
Information display of user setting (TRIP1) is turned
○ × OFF
ON/OFF.
Replacement interval of user setting (TRIP1) is
○ × 5000 hours
changed.
The user setting (TRIP1) replacement switch is pushed. × × -
Date/ the hour meter when user setting (TRIP1) was
○ × -
The user setting (TRIP2) is displayed/ is not displayed. × × Displayed
T5-2-68
Setting Function
Factory Set-
Dr. ZX ting
Unit
Maintenance Information display of user setting (TRIP2) is turned
○ × OFF
Setting ON/OFF.
Replacement interval of user setting (TRIP2) is
○ × 5000 hours
changed.
The user setting (TRIP2) replacement switch is
× × -
pushed.
Date/ the hourmeter when user setting (TRIP2) was
○ × -
Optional Work mode function is displayed/ is not displayed. × ○(Monitor Controller) Displayed
Function
Not
ML carne function is displayed/ is not displayed. × ○(Monitor Controller)
displayed
ML crane switch is turned ON/OFF. ○ × -
The switch ON/OFF is stored/ is not stored. × ○(Monitor Controller) Stored
Mail function is displayed/ is not displayed. × ○(Monitor Controller) Not displayed
The mail is sent. ○ × -
Overload
Overload alarm is displayed/ is not displayed. × ○(Monitor Controller) Not displayed
Alarm
Fuel Rate Fuel rate display/No display is displayed/ is not dis-
Display/No played on the main menu.
Display Fuel consumption gauge is turned ON/OFF. ○ × OFF
Back Moni- Back monitoring setting is displayed/ is not displayed
tor Setting on the main menu.
The camera image is selected/ is not selected auto-
○ × Not selected
matically when the machine travels. (Auto-switch)
The camera image is flipped horizontally. (Display
× ○(Monitor Controller) Normal image
type)
The camera image is flipped vertically. (Display type 2) × ○(Monitor Controller) Flip vertical
NTSC/PAL is selected. (Image type) × ○(Monitor Controller) NTSC
Language The language displayed on the monitor is selected. ○ × Japanese
Setting The language is registerd to the monitor / is deleted
× × -
from the monitor.
The language registered on the monitor is checked. ○ × -
Trouble- The fault code which the trouble occurs on is checked. ○ ○(Trouble shooting) -
shooting The fault code which the trouble occurred is checked. × ○(Trouble shooting) -
The fault code is completed. (Retrial B) × ○(Trouble shooting) -
Monitoring The item order is changed. ○ × -
The item order is set to the initialized one. ○ × -
T5-2-69
(Blank)
T5-2-70
TROUBLESHOOTING / Dr. ZX
OUTLINE
Dr. ZX is used for diagnosis of electrical system
including MC, EMC, ICF and monitor unit.
Dr. ZX is connected to ICF and failure of each
controller and each sensor is displayed as a fault code.
(Self-Fiagnostic Result)
Dr. ZX displays the input status of sensors and

switches connected to each controller and the output
status to actuator including solenoid valve from
controller with the machine operated in real time.
(Controller Diagnosis)
T5-3-1
Operation
1. Connect Palm (Dr. ZX) to the diagnosing ZX200-3 class, ZX240-3 class, 270-3 class
connector in the cab by using the Hot Sync cable
and connecting harness.
2. Turn the key switch ON or start the engine.
3. When turning Palm ON, the following screen is
displayed on the display of Palm.
3-1. Initial Screen
Select Dr. ZX icon.
3-2. Password Setup Screen (When the
password has unset) Set the password.
3-3. Service Software Selection Screen
+ Select ZX-3 Mid. Dr. ZX
T1V1-05-07-001
Connector
3-4. Function Selection Screen
+ Self-Diagnostic Result
ZX225US-3 class, ZX225USR-3 class
+ Select Controller
Dr. ZX
Connector
4. Select Self-Diagnostic Result and operate
according to the instruction under the screen.
T1V1-01-02-047
Palm
（Dr. ZX）
Hot Sync Cable
Connecting
Harness
Figure No.
3108613
T1V1-05-07-002
T5-3-2
Start
Initial Screen
Password Setup Screen
• Input Password
Input the former
When the password has unset
Communication password (6 characters
Error or more).
Next time, input the
• Check Communication Hraness same password in order
• Check Fuse to check and push OK.
When the password has set
Service Software
Selection Screen
Select ZX-3 Mid T1V7-05-03-165
Self-Diagnostic
Result Function Select Controller
Select
Function
Engine ICF Monitor
Main Controller
Controller Controller Controller
Self-Diagnostic
Result of Each Record Main Menu Main Menu Main Menu Main Menu
Controller • Monitor Display • Monitor Display • Information C/U • Monitoring
• Special Function • Special Function Various Setup • Various Setup
• Setup Disp. Record • Data Download Password Change
Select Controller Password Change Save Data Check
Disp. Record
Password Change
Password Change
Op. Manual.
Retry B
Self-Diagnostic
Result
T5-3-3
Self-Diagnostic Result
The self-diagnostic result of each controller is
displayed.
After starting Dr. ZX, push Self-Diagnostic Result.
T1V7-05-03-001 T1V7-05-03-008 T1V7-05-03-002

Function Selection Screen Controller Self- Diagnosis Screen
NOTE: Main C/U: MC

Engine C/U: ECM
Monitor Unit: Monitor Unit
Information C/U: ICF
NOTE: Self-diagnosis of ICF controller is done on

the next page.
T5-3-4
Self-Diagnosis
Push Fault of ICF Controller. In
After starting Dr. ZX, push case of no faulty, No Fault is
Self-Diagnostic Result. displayed.
To the
lower
T1V7-05-03-001 T1V7-05-03-008 T1V7-05-03-002

Function Selection Screen Controller Self- Diagnosis Screen
By changing the page, the forward and
By changing the page, the backward fault code is displayed.
Push Details, and Details of the forward and backward fault Push Retry B and return to
fault code and Corrective Action code is displayed. Controller Self-Diagnosis Screen
are displayed. after executing Retry B.
Push ESC and Retry B is Push ESC and Retry B Screen is Push ESC and return to Controller
displayed. displayed. Self-Diagnosis Screen directly.
Trouble Retry B
ESC ESC
T1V7-05-03-003 T1V7-05-03-005 T1V7-05-03-007
Retry B Screen
If the message of Details is
long, push the arrow and
change the screen.
Retry B
ESC
T1V7-05-03-002
Controller Self- Diagnosis Screen
T5-3-5
SELECT CONTROLLER
Select failure-diagnosis controller.
After starting Dr. ZX, push Select Controller.
T1V7-05-03-001 T1V7-05-03-009
Function Selection Screen
NOTE: Main C/U: MC

Engine C/U: ECM
Monitor Unit: Monitor Unit
Information C/U: ICF
T5-3-6
MAIN CONTROLLER
Title Screen
Recorded Data
Displays data recorded in MC by one day by using Dr.
ZX.
Password Change
Changes the password input when setting.
Main Menu
• Monitor Display
Displays the control signals of MC and the input
signals from each switch and sensor.
• Special Function
Makes Special Function disabled. T1V7-05-03-011
Return to Controller
• Setup Selection Screen.
Password Disp. Record
Adjusts engine speed, pump delivery flow rate, Change
solenoid valve output pressure and so on. Main Controller Screen
T1V7-05-03-010
Selection Screen.
Main Menu Screen
T1V7-05-03-012
Monitor Display
Special Function
Setup
T5-3-7
MAIN MENU MONITOR DISPLAY
Dr. ZX displays the input signals from switches and
sensors and the control signals from MC.
List of Monitor Item

Item Data Unit
Selecting Monitoring
-1
Required Engine Speed Requested Engine Input signal from engine control dial min
Speed
-1
Actual Engine Speed Actual Engine Input signal from ECM min
Speed
-1
Engine Speed Deviation Engine Speed De- Input signal from ECM min
viation
Pump 1 Delivery Pressure Pump 1 Delivery Input signal from pump 1 delivery MPa
Pressure pressure sensor
Pump 1 Pump Control Pressure Pump 1 Flow Con- Input signal from pump 1control pres- MPa
trol Pressure sure sensor
Pump 1 Flow Rate Limit Propor- Pump 1 Flow Rate Control instruction signal to maximum MPa
tional Valve Output Limit P/S/V Out pump 1 flow rate limit control solenoid
valve
3
Pump 1 Max. Displacement Pump 1 Upper Calculated value from engine speed cm
Limit Displace- and pump 1 delivery pressure (only
ment when using the attachment)
Pump 1 Target Flow Rate Pump 1 Target Control instruction signal to maximum L/min
Flaw Rate pump 1 flow rate limit control solenoid
valve
Pump 2 Delivery Pressure Pump 2 Delivery Input signal from pump 2 delivery MPa
Pressure pressure sensor
Pump 2 Pump Control Pressure Pump 2 Flow Con- Input signal from pump 2control pres- MPa
trol Pressure sure sensor
Pump 2 Flow Rate Limit Propor- Pump 2 Flow Rate Control instruction signal to maximum MPa
tional Valve Output Limit P/S/V Out pump 2 flow rate limit control solenoid
valve
3
Pump 2 Max. Displacement Pump 2 Upper- Calculated value from engine speed cm
Limit Displace- and pump 2 delivery pressure (only
ment when using the attachment)
Pump 2 Target Flow Rate Pump 2 Target Control instruction signal to maximum L/min
Flaw Rate pump 2 flow rate limit control solenoid
valve
Pump Torque Proportional Valve Pump Torque P/S Control instruction signal to torque MPa
Output Valve Output control solenoid valve
Pump 3 Delivery Pressure (Op- Pump 3 Delivery Input signal from pump 3 delivery MPa
tional) Pressure pressure sensor
Pump 1 Load Rate Pump 1 Load Load rate of pump 1 %
Factor (Rate)
Pump 2 Load Rate Pump 2 Load Load rate of pump 2 %
Factor (Rate)
T5-3-8
Item Data Unit

Type of Current ATT Current ATT Type Communication from monitor unit BK, BR, PU, CR,
VI, Others
Number of Current ATT Current ATT No. Communication from monitor unit 1, 2, 3, 4, 5
Type of ATT1 ATT1 Type Communication from monitor unit BK, BR, PU, CR,
VI, Others
Number of ATT1 ATT1 No. Communication from monitor unit 1, 2, 3, 4, 5
VI, Others
VI, Others
VI, Others
VI, Others
Front Att. Control Pressure Front Pilot Pres- Input signal from pressure sensor MPa
sure (front att.)
Boom Raise Control Pressure Boom Raise Pilot Input signal from pressure sensor MPa
Pressure (boom raise)
Arm Roll-In Control Pressure Arm Roll-in Pilot Input signal from pressure sensor MPa
Pressure (arm roll-in)
Arm Dump Control Pressure Arm Roll-Out Pilot Input signal from pressure sensor MPa
Pressure (arm roll-out)
Swing Control Pressure Swing Pilot Pres- Input signal from pressure sensor MPa
sure (swing)
Travel Control Pressure Travel Pilot Pres- Input signal from pressure sensor MPa
sure (travel)
ATT Control Pressure (Optional) Att. Control Pilot Input signal from pressure sensor MPa
Pressure (auxiliary)
EC Dial Angle EC Dial Angle Input signal from EC sensor V
Boom Cylinder Bottom Pressure Boom Bottom Input signal from boom bottom pres- MPa
(Optional) Pressure sure sensor
Boom Cylinder Rod Pressure Boom Rod Pres- Input signal from boom rod pressure MPa
(Optional) sure sensor
Arm Cylinder Bottom Pressure Arm Bottom Input signal from arm bottom pres- MPa
(Optional) Pressure sure sensor
Boom Angle (Optional) Boom Angle Input signal from boom angle sensor V
Arm Angle (Optional) Arm Angle Input signal from arm angle sensor V
E/P Mode Switch E/P SW Power mode switch selection status E, P
HP Mode Switch HP Mode SW Power mode switch selection status ON, OFF
Auto-Idle Switch Auto-Idle SW Auto-idle switch ON/OFF status AI
Travel Mode Switch Travel Mode SW Travel mode switch selection status LO, HI
Power Digging Switch Power Boost SW Power digging switch selection status ON, OFF
Key Switch Key SW Key switch ON/OFF status ON, OFF
T5-3-9
Item Data Unit

Boom Dampener Switch 1 Boom Damping Boom dampener switch 1 ON/OFF ON, OFF
(Optional) SW1 status
Boom Dampener Switch 2 Boom Damping Boom dampener switch 2 ON/OFF ON, OFF
(Optional) SW2 status
Low Vibration Switch (Optional) Low Vibration SW Low vibration switch ON/OFF status ON, OFF
Low Vibration Mode ON/OFF Low Vibration Mode Low vibration mode switch 1 ON/OFF ON, OFF
Switch (Optional) ON/OFF SW status
Digging Regenerative Propor- Dig-Regenerative Control instruction signal to solenoid MPa
tional Valve Output P/S Valve Output valve unit SF
Arm Regenerative Proportional Arm Regenerative Control instruction signal to solenoid MPa
Valve Output P/S Valve Output valve unit SC
Power Digging Control Pressure Power Boost Con- Control instruction signal to solenoid MPa
trol Pressure valve unit SG
Travel Mode Control Pressure Travel Motor Con- Control instruction signal to solenoid MPa
trol Pressure valve unit SI
ATT. Proportional Valve Output ATT P/S Valve Control instruction signal to ATT. pro- MPa
(Optional) Output portional valve output
Boom Dampener Proportional Boom Damper P/S Control instruction signal to boom MPa
Valve Output (Optional) Valve Output dampener proportional valve
Low Vibration Proportional Valve Low Vibration P/S Control instruction signal to low vibra- MPa
Output (Optional) Valve Output tion proportional valve
Pump 1 Flow Rate Limit Propor- Pump 1 Flow Rate Feedback of pump 1 flow rate limit mA
tional Valve Output (Optional) FB Limit P/S/V Out FB proportional valve output
Pump 2 Flow Rate Limit Propor- Pump 2 Flow Rate Feedback of pump 2 flow rate limit mA
tional Valve Output FB Limit P/S/V Out FB proportional valve output
Pump Torque Proportional Valve Pump Torque P/S Feedback of pump torque propor- mA
Output FB Valve Output FB tional valve output
ATT Proportional Valve Output ATT P/S Valve Feedback of ATT proportional valve mA
(Optional) FB Output FB output
Boom Dampener Proportional Boom Damper P/S Feedback of boom dampener propor- mA
Valve Output (Optional) FB Valve Output FB tional valve output
Low Vibration Proportional Valve Low Vibration P/S Feedback of low vibration proportional mA
Output (Optional) FB Valve Output FB valve output
Digging Regenerative Propor- Dig-Regenerative Feedback of digging regenerative mA
tional Valve Output FB P/S/V Output FB proportional valve output
Arm Regenerative Proportional Arm Regenerative Feedback of arm regenerative propor- mA
Valve Output FB P/S/V Output FB tional valve output
Power Digging Control Pressure Power Boost Chg. Feedback of power digging control mA
FB Over Pressure FB pressure
Travel Mode Control Pressure Travel 2-Speed Feedback of travel mode control pres- mA
FB Chg. Ovr. sure
Pressure FB
T5-3-10
Item Data Unit

Travel Alarm (Optional) Travel Alarm Travel alarm Action/No Action status Action,
No Action
Swing Alarm (Optional) Swing Alarm Swing alarm Action/No Action status Action,
No Action
Load Alarm (Optional) Load Alarm Load alarm Action/No Action status Action,
No Action
Auto Air Bleeding (Optional) Auto-Air Bleeder Auto air bleeding ON/OFF status ON, OFF
Hydraulic Oil Temperature Hydraulic Oil Tem- Input signal from hydraulic oil tem- °C
perature (HOT) perature sensor
Overload Alarm ON/OFF Switch Load Alarm Overload alarm switch ON/OFF status ON, OFF
(Optional) ON/OFF SW
Angle Sensor Learning Status Angle Sensor Communication from monitor unit Not Learn, Fin-
(Optional) Learning Status ish, Final
NOTE: ATT: Attachment BK: Digging

BR: Hydraulic Breaker PU: Secondary Crusher
CR: Primary Crusher
VI: Vibrating Hammer
T5-3-11
Monitor Display
After starting Dr. ZX, push Select

Controller. Push Main C/U. Push Start.
To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-011

Function Selection Screen Controller Selection Screen Main Controller Screen
Push OK. Push Monitor Display.
To the
lower
T1V7-05-03-010 T1V7-05-03-012 T1V7-05-03-013

Title Screen Main Menu Screen Enter Model and Serial No.
Screen
Push Hold and the monitor is stopped
Push the item for Monitor Display temporarily. When the monitor is
Input the model code and serial and push OK. Refer to T5-3-8 as started again, push Hold again. Push
No. and push OK. Push ESC and for the monitor item. Push ESC ESC and return to Display Item
return to Main Menu Screen. and return to Main Menu Screen. Selection Screen.
T1V7-05-03-065 T1V7-05-03-014 T1V7-05-03-015
Enter Model and Serial No. Screen Display Item Selection Screen Monitor Screen
To the next page
T5-3-12
Push Rec. No. and the recording

Push Record. screen for Rec. No. is made.
To the
lower
T1V7-05-03-015 T1V7-05-03-096 T1V7-05-03-097
Monitor Screen Select Write Data-Bank Screen
If Rec. No. has already been If Rec. No. has not been recorded
recorded and push Over Write, yet and push Write, data is written Push Comment.
data is overwritten. Push ESC and to the recording screen. Push ESC Push ESC and return to Main
return to Main Menu Screen. and return to Main Menu Screen. Menu Screen.
To the
lower
T1V7-05-03-098 T1V7-05-03-100 T1V7-05-03-099

Recording Screen Recording Screen
Push Re-Input and return to

Recording Screen (Comment
Input).
Input Weather and Person’s name Push OK and the recording screen Push ESC and return to Main
in change and push OK. (making) is finished. Menu Screen.
T1V7-05-03-101 T1V7-05-03-102 T1V7-05-03-103

Input)
T5-3-13
SPECIAL FUNCTION
Auto Warm-Up Control: Deactivation

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-011

Push OK. Push Special Function.
To the
lower
T1V7-05-03-010 T1V7-05-03-012 T1V7-05-03-016

Title Screen Main Menu Screen
Push WU Dectivation. Push Exec. Push ESC and return Push ESC and return to WU
Push ESC and return to Main to WU Deactivation/ECO Deactivation/ECO Deactivation
Menu Screen. Deactivation Selection Screen. Selection Screen.
T1V7-05-03-017 T1V7-05-03-018 T1V7-05-03-019

WU Deactivation/ECO
Deactivation Selection Screen
NOTE: If starting again with the key switch OFF,

auto warm-up control becomes activated.
T5-3-14
ECO Control: Deactivation

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-011

Push OK. Push Special Function.
To the
lower
T1V7-05-03-010 T1V7-05-03-012 T1V7-05-03-016

Push Exec.
Push ECO Deactivation. Push ESC and return to WU Push ESC and return to WU
Push ESC and return to Main Deactivation/ECO Deactivation Deactivation/ECO Deactivation
Menu Screen. Selection Screen. Selection Screen.
T1V7-05-03-017 T1V7-05-03-020 T1V7-05-03-021

WU Deactivation/ECO
Deactivation Selection Screen
NOTE: If starting again with the key switch OFF,

ECO control becomes activated.
T5-3-15
SETTING
Engine speed, pump delivery flow rate, solenoid valve output pressure and so on can be adjusted.
Parameter Change
Item Data Unit
-1
Li Speed Adjustment Adjustment of slow idle engine speed min
-1
WU Speed Adjustment Adjustment of auto warming-up engine speed min
-1
AI Speed Adjustment Adjustment of auto-idle engine speed min
-1
P Speed Adjustment Adjustment of P mode engine speed min
Pump PQ Torque Adjustment of pump P-Q curve N⋅m
Adjustment
Boom Dampener Adjustment of solenoid valve MPa
Proportional Valve
Adjustment
ATT Proportional Valve Adjustment of optional solenoid valve MPa
Adjustment
ATT Speed Increase Down Setting of time required for engine speed decrease ms
Waiting Time
ATT Torque Down ON/OFF ON/OFF of torque down control when the attachment is ON, OFF
operated
ECO Control Selection ON/OFF of ECO control ON, OFF
HP Control Selection ON/OFF of HP control ON, OFF
ATT Mode Memory ON/OFF ON/OFF of attachment mode memory ON, OFF
Selection
Heater Control Selection ON/OFF of heater control ON, OFF
Engine Control Theft ON/OFF of engine control theft prevention ON, OFF
Prevention Selection
Pump Control Theft ON/OFF of pump control theft prevention ON, OFF
Prevention Selection
Min, Boom CYL. Bottom Setting of minimum boom cylinder bottom pressure over MPa
Pressure Over Balance balance
IMPORTANT: When turning the key switch to the
OFF position with the ATT mode
memory ON/OFF selection OFF, the
selected work mode becomes
ineffective and returns to the digging
mode. Next time, the work mode
should be selected. When turning
the key switch to the OFF position
with the ATT mode memory ON/OFF
selection ON, the selected work
mode becomes effective.
T5-3-16
Attachment Parameter Change

Item Data Unit
ATT1
ATT1 ATT Type Attachment selection BR PU CR VI
Others Non
ATT1 ATT No. Attachment setting number selection 12345
ATT1 P1 Max Swash Angle Adjustment of lower limit of maximum pump 1 flow rate L/min
Adjustment when using attachment
-1
ATT1 Engine Speed Adjustment of engine speed when using attachment min
Increase/Decrease
ATT1 Secondary Pilot Relief Secondary pilot relief valve ON/OFF selection ON, OFF
Pressure Selection
ATT1 Selector Valve Selector valve ON/OFF selection ON, OFF
Selection
ATT1 Accumulator Accumulator ON/OFF selection ON, OFF
Selection
ATT1 2-Speed Selection 2-speed selection ON/OFF selection ON, OFF
ATT2
Others Non
-1
Increase/Decrease
Pressure Selection
Selection
Selection
NOTE: ATT: Attachment
BR: Hydraulic Breaker
PU: Secondary Crusher
CR: Primary Crusher
Others: Other Attachments
Non: Attachment Unset
T5-3-17
Item Data Unit

ATT3
Others Non
-1
Increase/Decrease
Pressure Selection
Selection
Selection
ATT4
Others Non
-1
Increase/Decrease
Pressure Selection
Selection
Selection
CR: Primary Crusher
T5-3-18
Item Data Unit

ATT5
Others Non
-1
Increase/Decrease
Pressure Selection
Selection
Selection
CR: Primary Crusher
T5-3-19
ADJUSTMENT DATA LIST
ZX200-3 class
Min. Adjustable Range
Standard
Adjustment Data Adjustment Remarks
Range Adjustment
Value
-1 -1 -1
Li Speed 10 min 0 to 400 min 0 min
-1 -1 -1
WU Speed 10 min -450 to 200 min 0 min
-1 -1 -1
AI Speed 10 min -400 to 400 min 0 min
-1 -1 -1
P Speed 10 min -200 to 200 min 0 min
Pump PQ Torque
2.45 N⋅m -60 to 60 N⋅m 0 N⋅m
Adjustment
Boom Dampener
0.0196 MPa -0.9996 to 0.9996 MPa 0 MPa
Proportional Valve
ATT Proportional Valve 0.0196 MPa -0.9996 to 0.9996 MPa 0 MPa
ATT Speed Increase Down
40 ms 0 to 3000 ms 0 ms
Waiting Time
Min, Boom CYL. Bottom
0.2 MPa -9.8 to 14.7 MPa 0 MPa
Pressure Over Balance
ZX225US-3 class
Standard
Range Adjustment
Value
-1 -1 -1
-1 -1 -1
-1 -1 -1
-1 -1 -1
Pump PQ Torque
2.45 N⋅m -60 to 60 N⋅m 0 N⋅m
Adjustment
Boom Dampener
0.0196 MPa -0.9996 to 0.9996 MPa 0 MPa
Proportional Valve
40 ms 0 to 3000 ms 0 ms
Waiting Time
0.2 MPa -9.8 to 14.7 MPa 0 MPa
2
NOTE: 1 MPa=10.197 kgf/cm
2
1 kgf/cm =0.098 MPa
T5-3-20
ZX225USR-3 class
Standard
Range Adjustment
Value
-1 -1 -1
-1 -1 -1
-1 -1 -1
-1 -1 -1
Pump PQ Torque
2.45 N⋅m -60 to 60 N⋅m 0 N⋅m
Adjustment
Boom Dampener
0.0196 MPa -0.9996 to 0.9996 MPa 0 MPa
Proportional Valve
40 ms 0 to 3000 ms 0 ms
Waiting Time
0.2 MPa -9.8 to 14.7 MPa 0 MPa
ZX240-3 class
Standard
Range Adjustment
Value
-1 -1 -1
-1 -1 -1
-1 -1 -1
-1 -1 -1
Pump PQ Torque
2.45 N⋅m -60 to 60 N⋅m 0 N⋅m
Adjustment
Boom Dampener
0.0196 MPa -0.9996 to 0.9996 MPa 0 MPa
Proportional Valve
40 ms 0 to 3000 ms 0 ms
Waiting Time
0.2 MPa -9.8 to 14.7 MPa 0 MPa
2
2
1 kgf/cm =0.098 MPa
T5-3-21
ZX270-3 class
Standard
Range Adjustment
Value
-1 -1 -1
-1 -1 -1
-1 -1 -1
-1 -1 -1
Pump PQ Torque
2.45 N⋅m -100 to 100 N⋅m 0 N⋅m
Adjustment
Boom Dampener
0.0196 MPa -0.9996 to 0.9996 MPa 0 MPa
Proportional Valve
40 ms 0 to 3000 ms 0 ms
Waiting Time
0.2 MPa -9.8 to 14.7 MPa 0 MPa
2
2
1 kgf/cm =0.098 MPa
T5-3-22
(Blank)
T5-3-23
ATTACHMENT ADJUSTMENT DATA LIST
ZX200-3 class
Min.
Standard
Adjustment Data Adjustment Adjustable Range Remarks
Adjustment
Value
ATT1
ATT1 ATT Type/No. - 0 to 5 Breaker 1
ATT1 P1 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
ATT1 P2 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
ATT1 Engine Speed -1 -1 -1
10 min -500 to 200 min 0 min
Increase/Decrease
ATT1 Secondary Pilot
- ON/OFF ON
Relief Pressure Selection
ATT1 Selector Valve
- C/V or O/T O/T
Selection
ATT1 Accumulator
- ON/OFF OFF
Selection
ATT1 2-Speed Selection
- ON/OFF OFF
ATT2
ATT2 P1 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
ATT2 P2 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
10 min -500 to 200 min 0 min
Increase/Decrease
- ON/OFF OFF
ATT2 Selector Valve
- C/V or O/T O/T
Selection
ATT2 Accumulator
- ON/OFF ON
Selection
- ON/OFF OFF
ATT3
ATT3 ATT Type/No. - 0 to 5 Secondary Crusher 1
ATT3 P1 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
ATT3 P2 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
10 min -500 to 200 min 200 min
Increase/Decrease
- ON/OFF OFF
ATT3 Selector Valve
- C/V or O/T C/V
Selection
ATT3 Accumulator
- ON/OFF OFF
Selection
- ON/OFF ON
T5-3-24
Min.
Standard
Adjustment
Value
ATT4
ATT4 ATT Type/No. - 0 to 5 Primary Crusher 1
ATT4 P1 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angl4 Adjustment
ATT4 P2 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
10 min -500 to 200 min 200 min
Increase/Decrease
- ON/OFF OFF
ATT4 Selector Valve
- C/V or O/T C/V
Selection
ATT4 Accumulator
- ON/OFF OFF
Selection
- ON/OFF ON
ATT5
ATT5 ATT Type/No. - 0 to 5 Unregistration
ATT5 P1 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
ATT5 P2 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
10 min -500 to 200 min 0 min
Increase/Decrease
- ON/OFF Unregistration
ATT5 Selector Valve
- C/V or O/T Unregistration
Selection
ATT5 Accumulator
Selection
2
2
1 kgf/cm =0.098 MPa

CR: Primary Crusher C/V: Control Valve
VI: Vibrating Hammer O/T: Hydraulic Oil Tank
T5-3-25
ZX225US-3 class
Min.
Standard
Adjustment
Value
ATT1
ATT1 P1 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
ATT1 P2 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
10 min -500 to 200 min 0 min
Increase/Decrease
- ON/OFF ON
ATT1 Selector Valve
- C/V or O/T O/T
Selection
ATT1 Accumulator
- ON/OFF OFF
Selection
- ON/OFF OFF
ATT2
ATT2 P1 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
ATT2 P2 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
10 min -500 to 200 min 0 min
Increase/Decrease
- ON/OFF OFF
ATT2 Selector Valve
- C/V or O/T O/T
Selection
ATT2 Accumulator
- ON/OFF ON
Selection
- ON/OFF OFF
ATT3
ATT3 P1 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
ATT3 P2 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
10 min -500 to 200 min 200 min
Increase/Decrease
- ON/OFF OFF
ATT3 Selector Valve
- C/V or O/T C/V
Selection
ATT3 Accumulator
- ON/OFF OFF
Selection
- ON/OFF ON
T5-3-26
Min.
Standard
Adjustment
Value
ATT4
ATT4 P1 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angl4 Adjustment
ATT4 P2 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
10 min -500 to 200 min 200 min
Increase/Decrease
- ON/OFF OFF
ATT4 Selector Valve
- C/V or O/T C/V
Selection
ATT4 Accumulator
- ON/OFF OFF
Selection
- ON/OFF ON
ATT5
ATT5 P1 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
ATT5 P2 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
10 min -500 to 200 min 0 min
Increase/Decrease
ATT5 Selector Valve
Selection
ATT5 Accumulator
Selection
2
2
1 kgf/cm =0.098 MPa

T5-3-27
ZX225USR-3 class
Min.
Standard
Adjustment
Value
ATT1
ATT1 P1 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
ATT1 P2 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
10 min -500 to 200 min 0 min
Increase/Decrease
- ON/OFF ON
ATT1 Selector Valve
- C/V or O/T O/T
Selection
ATT1 Accumulator
- ON/OFF OFF
Selection
- ON/OFF OFF
ATT2
ATT2 P1 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
ATT2 P2 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
10 min -500 to 200 min 0 min
Increase/Decrease
- ON/OFF OFF
ATT2 Selector Valve
- C/V or O/T O/T
Selection
ATT2 Accumulator
- ON/OFF ON
Selection
- ON/OFF OFF
ATT3
ATT3 P1 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
ATT3 P2 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
10 min -500 to 200 min 200 min
Increase/Decrease
- ON/OFF OFF
ATT3 Selector Valve
- C/V or O/T C/V
Selection
ATT3 Accumulator
- ON/OFF OFF
Selection
- ON/OFF ON
T5-3-28
Min.
Standard
Adjustment
Value
ATT4
ATT4 P1 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angl4 Adjustment
ATT4 P2 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
10 min -500 to 200 min 200 min
Increase/Decrease
- ON/OFF OFF
ATT4 Selector Valve
- C/V or O/T C/V
Selection
ATT4 Accumulator
- ON/OFF OFF
Selection
- ON/OFF ON
ATT5
ATT5 P1 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
ATT5 P2 Max Swash
0.5 L/min 106 to 212 L/min 212 L/min
Angle Adjustment
10 min -500 to 200 min 0 min
Increase/Decrease
ATT5 Selector Valve
Selection
ATT5 Accumulator
Selection
2
2
1 kgf/cm =0.098 MPa

T5-3-29
ZX240-3 class
Min.
Standard
Adjustment
Value
ATT1
ATT1 P1 Max Swash
0.5 L/min 112 to 224 L/min 224 L/min
Angle Adjustment
ATT1 P2 Max Swash
0.5 L/min 112 to 224 L/min 224 L/min
Angle Adjustment
10 min -500 to 100 min 0 min
Increase/Decrease
- ON/OFF ON
ATT1 Selector Valve
- C/V or O/T O/T
Selection
ATT1 Accumulator
- ON/OFF OFF
Selection
- ON/OFF OFF
ATT2
ATT2 P1 Max Swash
0.5 L/min 112 to 224 L/min 224 L/min
Angle Adjustment
ATT2 P2 Max Swash
0.5 L/min 112 to 224 L/min 224/min
Angle Adjustment
10 min -500 to 200 min 0 min
Increase/Decrease
- ON/OFF ON
ATT2 Selector Valve
- C/V or O/T O/T
Selection
ATT2 Accumulator
- ON/OFF ON
Selection
- ON/OFF OFF
ATT3
ATT3 P1 Max Swash
0.5 L/min 112 to 224 L/min 224 L/min
Angle Adjustment
ATT3 P2 Max Swash
0.5 L/min 112 to 224 L/min 224 L/min
Angle Adjustment
10 min -500 to 100 min 100 min
Increase/Decrease
- ON/OFF OFF
ATT3 Selector Valve
- C/V or O/T C/V
Selection
ATT3 Accumulator
- ON/OFF OFF
Selection
- ON/OFF ON
T5-3-30
Min.
Standard
Adjustment
Value
ATT4
ATT4 P1 Max Swash
0.5 L/min 112 to 224 L/min 224 L/min
Angl4 Adjustment
ATT4 P2 Max Swash
0.5 L/min 112 to 224 L/min 224 L/min
Angle Adjustment
10 min -500 to 100 min 100 min
Increase/Decrease
- ON/OFF OFF
ATT4 Selector Valve
- C/V or O/T C/V
Selection
ATT4 Accumulator
- ON/OFF OFF
Selection
- ON/OFF ON
ATT5
ATT5 P1 Max Swash
0.5 L/min 112 to 224 L/min 224 L/min
Angle Adjustment
ATT5 P2 Max Swash
0.5 L/min 112 to 224 L/min 224 L/min
Angle Adjustment
10 min -500 to 100 min 0 min
Increase/Decrease
ATT5 Selector Valve
Selection
ATT5 Accumulator
Selection
2
2
1 kgf/cm =0.098 MPa

T5-3-31
ZX270-3 class
Min.
Standard
Adjustment
Value
ATT1
ATT1 P1 Max Swash
0.5 L/min 118 to 236 L/min 236 L/min
Angle Adjustment
ATT1 P2 Max Swash
0.5 L/min 118 to 236 L/min 236 L/min
Angle Adjustment
10 min -500 to 100 min 0 min
Increase/Decrease
- ON/OFF ON
ATT1 Selector Valve
- C/V or O/T O/T
Selection
ATT1 Accumulator
- ON/OFF OFF
Selection
- ON/OFF OFF
ATT2
ATT2 P1 Max Swash
0.5 L/min 118 to 236 L/min 236 L/min
Angle Adjustment
ATT2 P2 Max Swash
0.5 L/min 118 to 236 L/min 236 L/min
Angle Adjustment
10 min -500 to 100 min 0 min
Increase/Decrease
- ON/OFF ON
ATT2 Selector Valve
- C/V or O/T O/T
Selection
ATT2 Accumulator
- ON/OFF ON
Selection
- ON/OFF OFF
ATT3
ATT3 P1 Max Swash
0.5 L/min 118 to 236 L/min 236 L/min
Angle Adjustment
ATT3 P2 Max Swash
0.5 L/min 118 to 236 L/min 236 L/min
Angle Adjustment
10 min -500 to 100 min 100 min
Increase/Decrease
- ON/OFF OFF
ATT3 Selector Valve
- C/V or O/T C/V
Selection
ATT3 Accumulator
- ON/OFF OFF
Selection
- ON/OFF ON
T5-3-32
Min.
Standard
Adjustment
Value
ATT4
ATT4 P1 Max Swash
0.5 L/min 118 to 236 L/min 236 L/min
Angl4 Adjustment
ATT4 P2 Max Swash
0.5 L/min 118 to 236 L/min 236 L/min
Angle Adjustment
10 min -500 to 100 min 100 min
Increase/Decrease
- ON/OFF ON
ATT4 Selector Valve
- C/V or O/T C/V
Selection
ATT4 Accumulator
- ON/OFF OFF
Selection
- ON/OFF ON
ATT5
ATT5 P1 Max Swash
0.5 L/min 118 to 236 L/min 236 L/min
Angle Adjustment
ATT5 P2 Max Swash
0.5 L/min 118 to 236 L/min 236 L/min
Angle Adjustment
10 min -500 to 100 min 0 min
Increase/Decrease
ATT5 Selector Valve
Selection
ATT5 Accumulator
Selection
2
2
1 kgf/cm =0.098 MPa

T5-3-33
TROUBLESHOOTING/ Dr. ZX
Setting
• Parameter Change

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-011

Push OK. Push Setup.
To the
lower
T1V7-05-03-010 T1V7-05-03-012 T1V7-05-03-016

Refer to T5-3-16 as for the item of

Input the password and push OK. Push Parameter Change. Parameter Change.Display the
Push Cancel and return to Main Push ESC and return to Main forward and backward item by
Menu Screen. Menu Screen. pushing these marks.
T1V7-05-03-022 T1V7-05-03-206 T1V7-05-03-105

Setup Password Input Screen Setup Item Selection Screen Parameter Change Selection
Screen
T5-3-34
Parameter Input
Example: Li Speed Adjustment
Input Value = Normal Value
Input the value and push Exec. Check Adjustment and push Exec.
Push ESC and return to Parameter Push ESC and return to Parameter
Push Li Speed Adjustment. Change Selection Screen. Change Selection Screen.
To the
lower
T1V7-05-03-105 T1V7-05-03-106 T1V7-05-03-113
Parameter Change Selection Parameter Input Screen

Screen
Push ESC and return to Parameter

Change Selection Screen.
T1V7-05-03-107
T5-3-35
Input Value = Current Value
Input the value and push Exec. Push Exec. Push ESC and return
Push ESC and return to Parameter to Parameter Change Selection
Push Li Speed Adjustment. Change Selection Screen Screen
To the
lower
T1V7-05-03-105 T1V7-05-03-106 T1V7-05-03-108

Screen

Change Selection Screen
T1V7-05-03-107
T5-3-36
Input Value > Maximum Value
(Input Value < Minimum Value)
Parameter Input Screen. Push Max
Input the value and push Exec. and the maximum value is input.
To the
lower
T1V7-05-03-105 T1V7-05-03-106 T1V7-05-03-109

Screen

T1V7-05-03-107
T5-3-37
When the input value cannot be divided

Parameter Input Screen. Push A or
Input the value and push Exec. B and the value of A or B is input.
To the
lower
T1V7-05-03-105 T1V7-05-03-106 T1V7-05-03-110

Screen

T1V7-05-03-107
T5-3-38
Status Selection
Example: ATT Torque Reducing On/Off: Off
Push OFF and Push Exec. Push Check OFF and push Exec. Push
Push ATT Torque Reducing On/Off. ESC and return to Parameter ESC and return to Parameter
Change Selection Screen. Change Selection Screen.
To the
lower
T1V7-05-03-179
T1V7-05-03-111 T1V7-05-03-112
Parameter Change Selection Status Selection Screen
Screen

T1V7-05-03-107
T5-3-39
• Attachment Parameter Change

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-011

Push OK. Push Setup.
To the
lower
T1V7-05-03-010 T1V7-05-03-012 T1V7-05-03-016

Refer to T5-3-17 as for the item of

Input the password and push OK. ATT Parameter Change. Display
Push ATT Parameter Change.
Push ESC and return to Main the forward and backward item by
Push ESC and return to Main
Menu Screen. pushing these marks.
Menu Screen.
T1V7-05-03-022 T1V7-05-03-206 T1V7-05-03-114

Setup Password Input Screen Setup Item Selection Screen Attachment Selection Screen
T5-3-40
Attachment Parameter Input
Input Value = Normal Value
Input the value and push Exec.

Push ATT1 P1 Swash Angle Push ESC and return to Parameter
Push ATT1. Adjustment. Change Screen.
To the
lower
T1V7-05-03-114 T1V7-05-03-115 T1V7-05-03-116

Attachment Selection Screen Parameter Change Screen Parameter Input Screen
Check Adjustment and push Exec.

Change Screen. Change Screen.
T1V7-05-03-117 T1V7-05-03-107
T5-3-41
Input Value = Current Value

To the
lower
T1V7-05-03-114 T1V7-05-03-115 T1V7-05-03-116

Push Exec. Push ESC and return Push ESC and return to Parameter
to Parameter Change Screen. Change Screen.
T1V7-05-03-118 T1V7-05-03-107
T5-3-42
Input Value > Maximum Value
(Input Value < Minimum Value)

To the
lower
T1V7-05-03-114 T1V7-05-03-115 T1V7-05-03-116


Parameter Input Screen. Push Max
and the maximum value is input.
T1V7-05-03-119 T1V7-05-03-107
T5-3-43
When the input value cannot be divided

To the
lower
T1V7-05-03-114 T1V7-05-03-115 T1V7-05-03-116


Parameter Input Screen. Push A or
B and the value of A or B is input.
T1V7-05-03-120 T1V7-05-03-107
T5-3-44
Status Selection
Example: ATT1, ATT No.
Push “5” and Push Exec. Push

ESC and return to ATT Parameter
Push ATT1. Push ATT1 Number. Change Selection Screen.
To the
lower
T1V7-05-03-114 T1V7-05-03-115 T1V7-05-03-123

Attachment Selection Screen Parameter Change Screen Status Selection Screen
Check number and push Exec.

Push ESC and return to ATT
Parameter Change Selection Push ESC and return to Parameter
Screen. Change Selection Screen.
T1V7-05-03-168 T1V7-05-03-107
T5-3-45
ATTACHMENT SETTING Monitor Unit
When the attachment is set by Dr. ZX, the attachment

specification screen can be selected and displayed on
the work mode screen of monitor unit.
(Push key 2 and select Breaker 1 in this group.)
NOTE: Refer to the monitor unit group as for the
display on work mode screen of monitor
unit.
When pushing key 6 and displaying the primary screen,

Key 2
the attachment mode which is selected on display the
work mode is displayed. T1V5-05-01-109
Work Mode Screen

Work Mode Display
Attachment Mode
Breaker
T1V1-05-01-104
Pulverizer
T1V1-05-01-105
Crusher
Key 6
T1V5-05-01-001
T1V1-05-01-106
Attachment Specification Screen (Breaker 1)
Vibrating Hammer
T1V1-05-01-107
Work
Others Mode
T1V1-05-02-003

pattern are same.
Breaker2 Hydraulic Breaker2 T1V1-05-03-006
Pulverizer1 Secondary Crusher1 Primary Screen
T5-3-46
Five kinds attachment can be selected from Breaker 1
to 5, pulverizer 1 to 5, crusher 1 to 5, vibrating hammer
1 to 5 and others 1 to 5.
(Refer to T5-3-17 to 19.)
NOTE: Attachment setting at the time of shipping

from the factory
Attachment 1: Breaker 1
Attachment 2: Breaker 2
Attachment 3: Pulverizer 1
Attachment 4: Crusher 1
Attachment 5: Non-setting
Attachment 2 Attachment 3
Attachment 4
Attachment 1 Attachment 5
T1V5-05-01-109
T5-3-47
Attachment Setting
Example: Set Pulverizer 5 to Attachment 1
Push PU and push Exec. Push
Push ATT 1. Push ATT1 ATT Type. Change Selection Screen.
To the
lower
T1V7-05-03-114 T1V7-05-03-115 T1V7-05-03-121

Attachment Selection Screen ATT Parameter Change Screen Status Selection Screen
Check PU and push Exec. Push Push ESC and return to ATT
ESC and return to ATT Parameter Parameter Change Selection
Change Selection Screen. Screen. Push ATT 1 Number.
To the
lower
T1V7-05-03-122 T1V7-05-03-107 T1V7-05-03-115

ATT Parameter Change Screen
Push “5” and push Exec. Push Check No. and push Exec. Push Push ESC and return to ATT
ESC and return to ATT Parameter ESC and return to ATT Parameter Parameter Change Selection
Change Selection Screen. Change Selection Screen. Screen.
T1V7-05-03-123 T1V7-05-03-168 T1V7-05-03-107

Status Selection Screen
T5-3-48
When the work mode screen of monitor unit is
displayed, Pulverizer 5 is displayed at Attachment 1.
When pushing key 2, Pulverizer 5 is selected and the
Pulverizer 5 specification screen is displayed.
Attachment 1 Attachment 2 Attachment 3 Attachment 4
Attachment 5
T1V5-05-03-004
Key 2
T5-3-49
Attachment Non-Setting
IMPORTANT: When the attachment is
“non-setting”, the attachment cannot
be selected on the monitor unit.
Example: Set Attachment to Non-Setting
Push Non and push Exec. Push
Push ATT 1. Push ATT1 ATT Type. Change Selection Screen.
To the
lower
T1V7-05-03-114 T1V7-05-03-115 T1V7-05-03-121

Attachment Selection Screen ATT Parameter Change Screen Status Selection Screen
Check Non and push Exec. Push Push ESC and return to ATT
ESC and return to ATT Parameter Parameter Change Selection
Change Selection Screen. Screen.
T1V7-05-03-178 T1V7-05-03-107
T5-3-50
When the work mode of monitor unit is displayed,
attachment 1 display disappears.
Attachment 1 Attachment 2 Attachment 3 Attachment 4
Attachment 5
T1V5-05-03-005
T5-3-51
Recorded Data Display

Controller. Push Main C/U. Push Disp. Record.
To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-011

Function Selection Screen Controller Selection Screen Title Screen
Push Hold and the monitor is

Push and select No. Push stopped temporarily.   Push Hold
Regeneration and the recorded again and restart regeneration.
data is regenerated.Push DEL and Push ESC and Main Menu Screen
data of selected No. is deleted. is displayed.
T1V7-05-03-124 T1V7-05-03-125
T1V7-05-03-012
Recorded Data Regeneration Main Menu Screen
Screen
T5-3-52
Password Change

Controller. Push Main C/U. Push Password.
To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-011

Input the registered Password and Input the new password and push Input the new password again and
push OK. OK. push OK.
To the
lower
T1V7-05-03-126 T1V7-05-03-127 T1V7-05-03-169
Push OK and return to Title

Screen.
T1V7-05-03-128
T5-3-53
(Blank)
T5-3-54
ENGINE CONTROLLER
Recorded Data Display
Data recorded in ECM is displayed by one day by
using Dr. ZX.
Password Change
The password can be changed.
Main Menu
• Monitor Display
Dr. ZX displays the input signals from sensors and the
control signals of ECM.
Return Controller
Selection Screen.
T1V7-05-03-204
T5-3-55
Special Function
• Data Upload From ECM
Upload one set of data from ECM to Dr.ZX.
Move ECM data to Dr.ZX before exchanging the
ECM.
• Data Download To ECM

After exchanging the ECM, download ECM data
from Dr. ZX to new ECM.
• Write Injector ID Code

When changing a cylinder injector, write
injector ID code by Dr. ZX.
• ECM Data Display

Displaying the engine serial number, ID code
of each cylinder injector on the Dr. ZX.
• Actuator Test
IMPORTANT: The actuator test should be done
by setting the engine control dial
to the minimum speed position.
Engine Speed Down

-1
Decrease engine speed 200 min from current
speed for 5 seconds.
Engine Speed Down & Stop Cylinder

-1
Decrease engine speed 200 min from current
speed for 5 seconds, and shut injector fuel
injection of selected cylinder for 5 seconds.
T1V7-05-03-205
T5-3-56
MAIN MENU
MONITOR DISPLAY
List of Monitor Item
Item
Unit Data
Engine Torque Engine Torque ％ Input signal from ECM
Actual Engine Speed Actual Engine -1 Input signal from crank speed sensor and cam angle
min
(Engine Speed) Speed sensor
Target Engine Speed Target Engine -1
min Input signal from engine control dial
Speed
Glow Signal Glow Signal OFF, ON Glow relay ON/OFF status
Coolant Temperature Coolant
(Engine Coolant Temperature °C Input signal from coolant temperature sensor
Temperature) (E)
Fuel Temperature Fuel
°C Input signal from fuel sensor
Temperature
Engine Oil Pressure Engine Oil
kPa Input signal from engine oil pressure sensor
Pressure
Fuel Flow Rate Fuel Flow L/h Input signal from ECM
Atmospheric Pressure Barometric
kPa Input signal from atmospheric pressure sensor
Pressure
Suction Temperature Intake Air
°C Input signal from intake-air temperature sensor
(Intake Air Temperature) Temperature
Boost Pressure Boost Pressure kPa Input signal from boost pressure sensor
Boost Temperature Boost
°C Input signal from boost temperature sensor
Temperature
Battery Voltage Battery Voltage V Input signal from ECM
Total Amount of Fuel Use Total Used
L Input signal from ECM
Fuel
T5-3-57
Monitor Display

Controller. Push Engine C/U. Push Start.
To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-011

Push OK. Push Monitor Display.
To the
lower
T1V7-05-03-010 T1V7-05-03-130 T1V7-05-03-013

Engine Controller Screen Main Menu Screen Enter Model and Serial No. Screen
Push the item for Monitor Display Push Hold and the monitor is
and push OK. Refer to T5-3-57 as stopped temporarily. When the
Input the model code and serial for the monitor item. monitor is started again, push Hold
No. and push OK. Push ESC and Push ESC and return to Main again. Push ESC and return to
return to Main Menu Screen. Menu Screen. Monitoring Item Selection Screen.
Start
recoding.
To the
next page
T1V7-05-03-065 T1V7-05-03-132 T1V7-05-03-133

Enter Model and Serial No. Screen Display Item Selection Screen Monitor Screen
T5-3-58
Push Rec. No. and the recording

Push Record. screen for Rec. No. is made.
To the
lower
T1V7-05-03-133 T1V7-05-03-134 T1V7-05-03-135

Monitor Screen Select Write Data-Bank Screen
If Rec. No. has already been If Rec. No. has not been recorded
recorded and push Over Write, yet and push Write, data is written
data is overwritten. to the recording screen. Push Comment.
Push ESC and return to Main Push ESC and return to Main Push ESC and return to Main
Menu Screen. Menu Screen. Menu Screen.
To the
lower
T1V7-05-03-170 T1V7-05-03-136 T1V7-05-03-137

Recording Screen Recording Screen

Input).
Input weather and person’s name Push OK and the recording screen Push ESC and return to Main
in change and push OK. (making) is finished. Menu Screen.
T1V7-05-03-138 T1V7-05-03-171 T1V7-05-03-139

Input)
T5-3-59
DATA UPLOAD FROM ECM
IMPORTANT: Upload one set of data from ECM.
ECM data should be uploaded
before removing the ECM when
exchanging it.

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-011

Push OK. Push Special Function. Push Data Upload From ECM.
To the
lower
T1V7-05-03-010 T1V7-05-03-130 T1V7-05-03-180

Engine Controller Screen Main Menu Screen Special Function Setup Screen
It takes 10 to 60 sec. for Push ESC to return to the Special

communication. Function Setup Screen.
T1V7-05-03-181 T1V7-05-03-182
T5-3-60
(Blank)
T5-3-61
DATA DOWNLOAD TO ECM

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-011

Push OK. Push Special Function. Push Data Download To ECM.
To the
lower
T1V7-05-03-010 T1V7-05-03-130 T1V7-05-03-180

Push Write.
Push ESC to return to the Special It takes 10 to 60 sec. for
Push Next. Function Setup Screen. communication.
To the
next page
T1V7-05-03-183 T1V7-05-03-184 T1V7-05-03-181
T5-3-62
When "Write Finish"

Push ESC to return to the Special
Function Setup Screen.
T1V7-05-03-181 T1V7-05-03-185
When "Write Failed"

Push "Retry" to write again.
Push ESC to return to the Special It takes 10 to 60 sec. for Push ESC to return to the Special
Function Setup Screen communication. Function Setup Screen.
T1V7-05-03-186 T1V7-05-03-181 T1V7-05-03-185
T5-3-63
WRITE INJECTOR ID CODE
Cylinder 1 to 4

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-011

Push OK. Push Special Function. Push Write Injector ID Code.
To the
lower
T1V7-05-03-010 T1V7-05-03-130 T1V7-05-03-180

Push a cylinder number which

Injector ID code to be written.
(Cylinder 1 is pushed in this
example.)
Push ESC to return to the Special Push ESC to return to the Cylinder
Push Next. Function Setup Screen. Selection Screen.
Write Injector
ID Code
To the
next page
T1V7-05-03-183 T1V7-05-03-187 T1V7-05-03-188

Cylinder Selection Screen Input Writing ID Code Screen
T5-3-64
Input Injector ID code, and then

push "Exec" When "Write Finish"
(Please reffer to ID code input It takes 10 to 60 sec. for Push ESC to return to the Cylinder
method) communication. Selection Screen.
T1V7-05-03-189 T1V7-05-03-181 T1V7-05-03-185

Input Writing ID Code Screen
When "Write Failed"

Push "Retry" to write again.
Push ESC to return to the Cylinder It takes 10 to 60 sec. for Push ESC to return to the Cylinder
Selection Screen communication. Selection Screen.
T1V7-05-03-186 T1V7-05-03-181 T1V7-05-03-185
Injector ID code input method

Input ID code of injecter ID plate of relevant cylinder. In ID Code Injector ID Plate
the case of figure,
Input following alpha-numerals:
MCD0→5500
D1D2→00B8
D3D4→A3D7
D5D6→C9B9
D7D8→BBE7
D9→A1
BC→D4
Need no input Injector
T1V7-05-03-190
T1V1-05-03-007
T5-3-65
ECM DATA DISPLAY

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-011

Push OK. Push Special Function. Push ECM Data Display.
To the
lower
T1V7-05-03-010 T1V7-05-03-130 T1V7-05-03-180

Engine serial number and injector Scroll down the screen by pushing
ID codes of cylinder 1 and 2 are ▼, injector ID code of cylinder 3 to
displayed. 6 will be displayed.
It takes 10 to 60 sec. for Push ESC to return to the Special Push ESC and return to Monitoring
communication. Function Setup Screen. Item Selection Screen.
T1V7-05-03-181 T1V7-05-03-192 T1V7-05-03-193
NOTE: On a four-cylinder engine,

injector ID code of cylinder 5
and 6 can be neglected.
T5-3-66
ACTUATOR TEST
Engine Speed Down
IMPORTANT: Operation must be done after setting

engine control dial to the munimum
speed position.

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-011

Move the item by using ▼ and

Push OK. Push Special Function. Push Actuator Test.
To the
lower
T1V7-05-03-010 T1V7-05-03-130 T1V7-05-03-194

Push Engine Speed Down.

Push ESC to return to the Special Decrease engine speed for 5 Push "OK" to return to the Actuator
Function Setup Screen. seconds. Test Selection Screen.
T1V7-05-03-195 T1V7-05-03-196 T1V7-05-03-197

Actuator Test Selection Screen
T5-3-67
Engine Speed Down & Stop Cylinder
IMPORTANT: Operation must be done after setting

engine control dial to the munimum
speed position.

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-011

Move the item by using ▼ and

Push Special Function. Push Actuator Test.
To the
lower
T1V7-05-03-010 T1V7-05-03-130 T1V7-05-03-194

Push Engine Speed Down & Stop Push a cylinder number which is to
Cylinder. be shutoff fuel injection.
Push ESC to return to the Special Push ESC to return to the Actuator
Function Setup Screen. Test Selection Screen.
To the
next page
T1V7-05-03-195 T1V7-05-03-198
Actuator Test Selection Screen
T5-3-68
When pushing a cylinder, engine

speed sill be decreased for 5
seconds, and shutoff fuel injection
of the selected cylinder for 5 Push “OK” to return to the Actuator
seconds. Test Selection Screen.
T1V7-05-03-200 T1V7-05-03-201
T5-3-69
EXAMPLE OF HOW ENGINE SPEED
DOWN & STOP CYLINDER FUNCTION
USED (ON A FOUR-CYLINDER ENGINE)
When fuel can not be injected on the cylinder 1, the
engine runs with three cylinders.
1. Set the engine control dial to the minumum speed
postion, and then decrease engine speed at 800
-1
min .
2. Stop the cylinder 1 by operating Engine Speed
Down & Stop Cylinder function, engine will run
-1
with 600 min and three-cylinder for 5 seconds.
The engine sounds like strained.
3. When stop the cylinder 2 by operating Engine
Speed Down & Stop Cylinder function, engine will
-1
run with 600 min and two-cylinder for 5 seconds.
The engine sounds like strained even worse.
4. By hearing sound difference of 2 and 3, the
cylinder 1 is determined to be failed.
T5-3-70
RECORED DATA DISPLAY

Controller. Push Engine C/U. Push Disp. Record.
To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-011

Push and select No. Push Push Hold and the monitor is
Regeneration and the recorded stopped temporarily
data is regenerated. Push DEL and When the monitor is started again,
data of selected No. is deleted. push Hoid again.
Push ESC and return to Main Push ESC and return to Main
Menu Screen. Menu Screen.
T1V7-05-03-124 T1V7-05-03-141
Recorded Data Regeneration
Screen
T5-3-71
PASSWORD CHANGE

Controller. Push Engine C/U. Push Password.
To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-011

Input the registered password and Input the new password and push Input the new password and push
push OK. OK. OK.
To the
lower
T1V7-05-03-126 T1V7-05-03-127 T1V7-05-03-169

Screen.
T1V7-05-03-128
T5-3-72
ICF CONTROLLER
Title Screen
Save Data Check
Daily report data, frequency distribution data, total
operating hours, alarm and failure which are saved in
ICF can be checked by using Dr. ZX.
Password Change
Main Menu
• Information C/U Various Setup
Initialization of information C/U, setting of model,
serial No. and time, and initialization of control
data can be done. T1V7-05-03-207
• Data Download Selection Screen.
Daily report data, frequency distribution data, total Password Save Data
Check
operating hours, alarm and failure which are ICF Controller Screen
recorded in ICF can be downloaded to Dr. ZX.
T1V7-05-03-024
Main Menu Screen
T1V7-05-03-208
Information C/U:
Various setup
Data Download
T5-3-73
MAIN MENU
INFORMATION C/U VARIOUS SETUP
List of Controller Data Setting Item
Item Range of Data

Information C/U: Initialize Initialize/ESC
Enter Model and Serial No. Model ASCII (4 characters) 0 to 9, A to Z
Serial No. 000000 to 999999
Enter Date and Time YY 2000 to 2100
Date MM 1 to 12
DD 1 to 31
HH 0 to 23
Time
MM 0 to 59
Control Data: Initialize Initialize/ESC
Satellite Terminal: Initialize DEL/ESC
Satellite Terminal No. Confirmation 12 digits: 0 to 9, A to Z
Communicating State Check ICF < = > Satellite Connect Conn/UnConn
Terminal Comm. OK/NG
Power ON/OFF
Satellite Terminal
Comm. Enable/Stop
Rod Aerial OK/NG
GPS Aerial OK/NG
Wave State ON/OFF
Un-Transmit Data Number 0～99
Last Transmitting Time YYYY/MM/DD hh: mm: ss
Enter Satellite Comm. Start/Stop
Start/Stop
T5-3-74
INFORMATION C/U: INITIALIZE

Controller. Push Information C/U. Push Start.
To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-209

Push Information C/U: Various

Push OK. Setup. Push Information C/U: Initialize.
To the
lower
T1V7-05-03-024 T1V7-05-03-210 T1V7-05-03-027

ICF Controller Screen Main Menu Screen Information C/U: Various Setup
Screen
Push Init and the controller
operating data is initialied. Push
ESC and return to Information C/U: Push OK and return to Information Push ESC and return to Main
Various Setup Screen. C/U: Various Setup Screen. Menu Screen.
Init
ESC
T1V7-05-03-028 T1V7-05-03-029 T1V7-05-03-027
Information C/U: Initialize Screen Information C/U: Various Setup

Screen
T5-3-75
ENTER MODEL AND SERIAL No.

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-209


Push OK. Setup. Push Enter Model and Serial No.
To the
lower
T1V7-05-03-024 T1V7-05-03-210 T1V7-05-03-027

Screen
Push OK after inputting model and
Push Exec and model and serial serial No. and return to Enter
No. can be input. Model and Serial No. Screen.
Push ESC and return to Push ESC and return to
Information C/U: Various Setup Information C/U: Various Setup Push ESC and return to Main
Screen. Screen. Menu Screen.
Exes ESC
ESC
OK
T1V7-05-03-030 T1V7-05-03-031 T1V7-05-03-027

Enter Model and Serial No. Screen Information C/U: Various Setup
Screen
T5-3-76
ENTER DATE AND TIME

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-209


Push OK. Push Enter Date and Time.
Setup.
To the
lower
T1V7-05-03-024 T1V7-05-03-210 T1V7-05-03-027

Screen
Push Set and the focused item is
YY. Push ESC and return to
Information C/U: Various Setup
Screen.
YY, MM, DD, HH and MM

The focused item is displayed reversely.
At first, the focused item is YY.
－＋
YY, MM, DD, HH and MM YY, MM, DD, HH and MM
Move the focused item. Value of the focused item is increased or
No repeat input. decreased one by one.
In case value is beyond maximum one: Change
T1V7-05-03-032 value into the minimum one
Enter Date and Time Screen In case value is below minimum one: Change
value into the maximum one
No repeat input.
T5-3-77
CONTROL DATA: INITIALIZE

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-209


Push OK. Setup. Push Control Data: Initialize.
To the
lower
T1V7-05-03-024 T1V7-05-03-210 T1V7-05-03-027

Screen
Push Init and the controller control
data is initialied. Push ESC and
return to Information C/U: Various Push OK and return to Information Push ESC and return to Main
Setup Screen. C/U: Various Setup Screen. Menu Screen.
Init
ESC
T1V7-05-03-033 T1V7-05-03-034 T1V7-05-03-027
Control Data: Initialize Screen Information C/U: Various Setup

Screen
T5-3-78
SATELLITE TERMINAL: INITIALIZE

Controller. Push ICF Controller. Push Start.
To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-209

Push T and move to the next

screen of Information C/U: Various
Push Information C/U: Various Setup Screen. Push Satellite
Push OK. Setup. Terminal: Initialize.
To the
lower
T1V7-05-03-024 T1V7-05-03-210 T1V7-05-03-035
Push Exec. Screen
Push ESC and return to
Information C/U: Various Setup Push OK and return to Information
Screen. C/U: Various Setup Screen.
Exec
ESC
T1V7-05-03-036 T1V7-05-03-145 Information C/U: Various Setup T1V7-05-03-035

Screen
T5-3-79
SATELLITE TERMINAL No. CONFIRMATION

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-209


Push Information C/U: Various Setup Screen. Push Satellite
Push OK. Setup. Terminal No. Confirmation.
To the
lower
T1V7-05-03-024 T1V7-05-03-210 T1V7-05-03-035
Screen
Confirm serial No. (12 digits). Push

ESC and return to Information C/U:
Various Setup Screen.
T1V7-05-03-037 T1V7-05-03-035
T5-3-80
COMMUNICATING STATE CHECK

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-209


Push Information C/U: Various Setup Screen. Push
Push OK. Setup. Communicating State Check.
To the
lower
T1V7-05-03-024 T1V7-05-03-210 T1V7-05-03-035
Screen
Check communicating state.
Unconn: Faulty harness Push T and move to the next
NG: Faulty harness for Comm. screen. Check communicating
OFF: Faulty harness, Faulty controller state of Rod Aerial and GPS Aerial.
Stop: Enter Satellite Comm. Start/Stop Push ESC and return to
Push ESC and return to Information Information C/U: Various Setup Push ESC and return to Main
C/U: Various Setup Screen. Screen. Menu Screen.
ESC
T1V7-05-03-142 T1V7-05-03-143 T1V7-05-03-035

When electrical wave of the satellite is caught,
Check the enclosed state. the items are turned into OK.
IMPORTANT: Check this with the key of machine
ON in outdoor. According to state
of electrical wave, it may take a
little longer time.
T5-3-81
ENTER SATELLITE COMM. START / STOP

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-209


Push Information C/U: Various Setup Screen. Push Enter Satellite
Push OK. Setup. Comm. Start/Stop Set.
To the
lower
T1V7-05-03-024 T1V7-05-03-210 T1V7-05-03-035
Screen
When starting Satellite Comm., push

Start and push Exec. When stopping
Satellite Comm., push Stop and push
Exec.
Push ESC and return to Information Push OK and return to Information Push ESC and return to Main
C/U: Various Setup Screen. C/U: Various Setup Screen. Menu Screen.
Exec
ESC
T1V7-05-03-146 T1V7-05-03-147 T1V7-05-03-035

Screen
T5-3-82
DATE DOWNLOAD

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-209

While downloading data, Download

Push OK. Push Data Download. Screen is displayed.
To the
lower
T1V7-05-03-024 T1V7-05-03-210 T1V7-05-03-038
ICF Controller Screen Main Menu Screen Data Download Screen
When downloading is completed If pushing Cancel on Data

normally, Normal End Screen is Download Screen, Alarm Screen is
displayed. Push OK and return to displayed. Push OK and return to Push ESC and return to Title
Main Menu Screen. Main Menu Screen. Screen.
T1V7-05-03-039 T1V7-05-03-148 T1V7-05-03-210

Normal End Screen Alarm Screen Main Menu Screen
T5-3-83
SAVE DATA CHECK

Controller. Push Information C/U. Push Save Data Check.
To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-209

Function Selection Screen Controller Selection Screen
Data saved in ICF is displayed.

Push OK and return to Main Menu
Screen.
T1V7-05-03-040
Save Data Check Screen
T5-3-84
PASSWORD CHANGE

Controller. Push Information C/U. Push Password.
To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-209
Input the registered password and Input the new password and push Input the new password again and
push OK. OK. push OK.
To the
lower
T1V7-05-03-126 T1V7-05-03-127 T1V7-05-03-169

Screen.
T1V7-05-03-128
T5-3-85
MONITOR CONTROLLER
Main Menu
• Monitoring
Dr. ZX displays the control signals of each
controller and the input signals from each sensor.
• Various Settings
Dr. ZX can set optional function setting, back
monitor setting, operating condition enable/
disable, time set function enable / disable,
maintenance setting, inner hour meter
synchronization and fuel consumption gauge
display ON/OFF selection.
Password Change
T1V7-05-03-211
T5-3-86
MONITORING
List of Monitoring Item
Item
Unit Data
Monitor Switch ∗ ∗∗ Switch state of monitor unit
Condition Check
Radiator Coolant Coolant °C Input signal from coolant temperature sensor
Temperature Temperature
Fuel Level Fuel Level % Input signal from fuel sensor
Security Signal Security Signal OFF, ON Communication from monitor unit
Mail Switch Mail Switch OFF, Fuel, Operating state of mail
Forwarding,
Repair,
General
∗ Display when monitoring
T1V7-05-03-044
∗∗ Unit
Switch 1 Switch 7
Switch 8 Switch 14
T5-3-87
Monitor Switch Condition Check
IMPORTANT: During Monitor Switch Condition

Check, another monitoring item
cannot be selected.

Controller. Push Monitor Unit. Push OK.
To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

Function Selection Screen Controller Selection Screen Monitor Controller Screen
Push item for monitoring and push

OK.
Push Start. Push Monitoring. Menu Screen.
To the
lower
T1V7-05-03-042 T1V7-05-03-043
T1V7-05-03-025
Main Menu Screen Monitoring Item Selection Screen
Title Screen

Menu Screen.
Switch 1 Switch 7
Switch 8 Switch 14
T1V7-05-03-044
Screen
T5-3-88
When the key on monitor unit is pushed, the switch on
Monitor Switch Condition Check Screen related to the
key is turned into black. (Key 3 is pushed here.)
If the switch is not turned into black, check the monitor
unit and the CAN harness.
Monitor Unit
Monitor SW Condition Check
Liquid crystals
screen
ESC

Screen
T1V1-05-01-123 Switch 3 is turned into black.
Push key 3.
T5-3-89
Other Monitoring

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

Push item for monitoring and push

OK. Refer to T5-3-87 as for the
monitoring item.
Push ESC and return to Main Menu
Push Start. Push Monitoring. Screen.
To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-043

Title Screen Main Menu Screen Monitoring Item Selection Screen
When pushing Hold, the monitor is

stopped temporarily.
When re-starting the monitor, push
Hold again. Push ESC and return
to Monitoring Item Selection
Screen.
T1V7-05-03-045
Monitoring Screen
T5-3-90
VARIOUS SETTINGS
List of Various Setup Item
Item Unit
Optional Function M1 (Optional Function 1 Allocate)
M2 (Optional Function 2 Allocate) Unset
M3 (Optional Function 3 Allocate) Work Mode Function
M4 (Optional Function 4 Allocate) Mail Function
M5 (Optional Function 5 Allocate) Auto Lubrication Function
M6 (Optional Function 6 Allocate) Collision Prevention Function
M7 (Optional Function 7 Allocate)
Overload Alarm Enable / Disable Disable/Enable
Back Monitor Setup Back Monitor Function Enable/Disable Disable/Enable
Back Monitor Display Normal/Flip Vertical Flip Vertical/Normal
Operating Condition Enable / Disable Disable/Enable
Time Set Function Enable / Disable Disable/Enable
Maintenance Setup Maintenance Function Enable / Disable Disable/Enable
Notification Function Enable / Disable Disable/Enable
Maintenance Display Item ON/OFF
Engine Oil OFF/ON
Engine Oil Filter OFF/ON
Hydraulic Oil OFF/ON
Hydraulic Oil Pilot Filter OFF/ON
Hydraulic Oil Full-Flow Filter OFF/ON
Pump Transmission OFF/ON
Swing Bearing Grease OFF/ON
Travel Device Oil OFF/ON
Swing Device Oil OFF/ON
Air Cleaner Filter OFF/ON
Engine/Air Conditioner V-belt OFF/ON
Air Conditioner Filter OFF/ON
Fuel Filter OFF/ON
Fuel Consumption Gauge Display ON/OFF Selection Disable/Enable
T5-3-91
OPTIONAL FUNCTION ALLOCATION
Example: Allocate E-mail for Menu 7

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

Push Start. Push Various Setting. Push Option Function Allocate.
To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-046

Title Screen Main Menu Screen Various Setup Item Screen
Execusion: Refer to the next page.

All Clear: Unset all settings of
Push Next. Push Next. menus 1 to 9.
Push ESC and return to Main Push Back and return to the former ESC: Return to Various Setting
Menu Screen. screen. Screen.
T1V7-05-03-047 T1V7-05-03-048 T1V7-05-03-155

Option Function Allocate Screen
T5-3-92
Move the item by using T and

push Menu 7.
To the
lower
T1V7-05-03-155 T1V7-05-03-050 T1V7-05-03-051
Option Function Allocate Execution

Screen is displayed. Push ESC
and return to Various Setup Item
Push ML Crane. Push Exec. Screen.
T1V7-05-03-149 T1V7-05-03-212 T1V7-05-03-213

Option Function Allocate Screen Option Function Allocate Execution
Screen
Function that can be selected: Unset

Work Mode
ML Crane
Collision Prevention
Auto Lubrication
Mail
If the functions that can be selected are too much to be
settled in one page, the next page can be displayed by
using a page change button.
IMPORTANT: The function that has already been

allocated cannot be selected.
T5-3-93
Allocate Mail for Menu 3

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

Push Start. Push Various Setup. Push Option Function Allocate.
To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-046

Push Next. Push Next.

Push ESC and return to Main Push Back and return to the former
Menu Screen. screen.
To the next
page
T1V7-05-03-047 T1V7-05-03-048 T1V7-05-03-155

T5-3-94
Push Menu 3. Push Mail. Push Exec.
To the
lower
T1V7-05-03-155 T1V7-05-03-152 T1V7-05-03-153


Screen.
T1V7-05-03-154 T1V7-05-03-046
Option Function Allocate Execution Various Setup Item Screen
Screen
Mail is displayed on the monitor unit screen.

When pushing key F3, Mail Screen is displayed.
Mail
Mail Screen
Key F3 T1V1-05-03-002 T1V5-05-01-037
T5-3-95
Make ML Crane for Menu 2 Disable

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

Push Start. Push Various Setting. Push Option Function Allocate.
To the
lower
Title Screen T1V7-05-03-025

Main Menu Screen T1V7-05-03-042 Various Setup Item Screen T1V7-05-03-046
Push Next. Push Next.

Push ESC and return to Main Push Back and return to the former
Menu Screen. screen.
To the next
page
T1V7-05-03-047 T1V7-05-03-048 T1V7-05-03-157

T5-3-96
Push Menu 2. Push Unset. Push Exec.
To the
lower
T1V7-05-03-157 T1V7-05-03-156 T1V7-05-03-155
Option Function Allocate Screen Option Function Allocate Screen

Screen.
T1V7-05-03-160 T1V7-05-03-046
Option Function Allocate Execution Various Setup Item Screen
Screen
ML Crane is disappeared on the monitor unit screen.

ML Crane
T1V1-05-03-001
T1V1-05-03-003
T5-3-97
OVERLOAD ALARM ENABLE / DISABLE
SELECTION
IMPORTANT: In case ML Crane is set to any one of
Overload Alarm: Enable Menu 1 to 9 of Option Function
Allocate, make ML Crane disable.

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

Push Overload warnig Enable/

Push Start. Push Various setting. Disable.
To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-046

Push Enable and push Exec. Push

ESC and return to the former Push ESC and return to Various
screen. Setup Item Screen.
T1V7-05-03-161 T1V7-05-03-162
NOTE: Push Enable, push ESC and

return to Various Setup Item
Screen, so that Overload
Alarm Enable is not set.
T5-3-98
Overload Alarm: Disable

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

Push Overload warnig Enable/

Push Start. Push Various setting. Disable.
To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-046

Push Disable and push Exec. Push

T1V7-05-03-163 T1V7-05-03-164
NOTE: Push Disable, push ESC and

Screen, so that Overload
Alarm Disable is not set
T5-3-99
BACK MONITOR SETTING
Back Monitor Function: Enable

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

Push Start. Push Various setting. Push Back Monitor Setup.
To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-046

Push Back Monitor Function Push Enable and push Exec. Push
Enable / Disable. Push ESC and ESC and return to Various Setup Push ESC and return to Various
return to the former screen. Item Screen. Setup Item Screen.
T1V7-05-03-052 T1V7-05-03-053 T1V7-05-03-054

Screen, so that Back Monitor
Function Enable is not set.
T5-3-100
Back Monitor Function: Disable

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-046

Push Back Monitor Function Push Disable and push Exec. Push
Enable / Disable. Push ESC and ESC and return to Various Setup Push ESC and return to Various
T1V7-05-03-052 T1V7-05-03-053 T1V7-05-03-057

Function Disable is not set.
T5-3-101
Back Monitor Function: Normal

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-046

Push Back Monitor Display Normal Push Normal and push Exec. Push
/ Filip Vartical. Push ESC and ESC and return to Various Setup Push ESC and return to Various
T1V7-05-03-052 T1V7-05-03-055 T1V7-05-03-058
NOTE: Push Normal, push ESC and

Display Normal is not set.
T5-3-102
Back Monitor Display: Flip Vertical

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-046

Push Back Monitor Display Push FV and push Exec. Push

Normal/Flip Vartical. Push ESC ESC and return to Various Setup Push ESC and return to Various
and return to the former screen. Item Screen. Setup Item Screen.
T1V7-05-03-052 T1V7-05-03-055 T1V7-05-03-056
NOTE: Push FV, push ESC and

Display Flip Vertical is not
set.
T5-3-103
OPERATING CONDITION ENABLE /
DISABLE SELECTION
Operating Condition: Enable

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

Push Operational condition

Push Start. Push Various setting. Enable/ Disable.
To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-046


T1V7-05-03-059 T1V7-05-03-060

Screen, so that Operating
Condition Enable is not set.
T5-3-104
Operating Condition: Disable

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

Push Operational condition

Push Start. Push Various setting. Enable/ Disable.
To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-046


T1V7-05-03-061 T1V7-05-03-062

Screen, so that Operating
Condition Disable is not set.
T5-3-105
TIME SETTING FUNCTION ENABLE /
DISABLE SELECTION
Time Setting Function: Enable

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041


push Time Set Func
Push Start. Push Various setting. Enable/Disable.
To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-214


T1V7-05-03-064 T1V7-05-03-066

Screen, so that Time Set
Function Enable is not set.
T5-3-106
Time Setting Function: Disable

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041


push Time Set Func
To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-214


T1V7-05-03-067 T1V7-05-03-068

Screen, so that Time Set
Function Disable is not set
T5-3-107
MAINTENANCE SETTING
MAINTENANCE OPERATION ALLOW /
NOT ALLOW SELECTION
Maintenance Operation: Allow
To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

Push Start. Push Various setting. push Maintenance Setup.
To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-214

Push Allow and push Exec. Push
Push Maintenance operation ESC and return to the former Push ESC and return to
Allow/Not Allow. screen. Maintenance setup Item Screen.
T1V7-05-03-069 T1V7-05-03-070 T1V7-05-03-071

Maintenance Setup Item Screen
NOTE: Push Allow, push ESC and
return to Maintenance Setup
Item Screen, so that
Maintenance Operation
Allow is not set.
T5-3-108
Maintenance Operation: Not Allow

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-214

Push Not Allow and push Exec.
Push Maintenance operation Push ESC and return to the former Various Setup Item Screen
Allow/Not Allow. screen.

Maintenance setup Item Screen.
T1V7-05-03-069 T1V7-05-03-072
NOTE: Push Not Allow, push ESC
and return to Maintenance T1V7-05-03-073
Setup Item Screen, so that
Maintenance Operation Not
Allow is not set.
T5-3-109
NOTIFICATION FUNCTION ENABLE /
DISABLE SELECTION
Notification Function: Enable
To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-214

Push Notification function ESC and return to the former Push ESC and return to
Enable/Disable. screen Maintenance setup Item Screen.
T1V7-05-03-069 T1V7-05-03-074 T1V7-05-03-075

Notification Function Enable
is not set.
T5-3-110
Notification Function: Disable

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-214

Push Notification function ESC and return to the former Push ESC and return to
Enable/Disable. screen. Maintenance setup Item Screen.
T1V7-05-03-069 T1V7-05-03-076 T1V7-05-03-077

Notification Function Disable
is not set.
T5-3-111
MAINTENANCE DISPLAY ITEM ON/OFF
SELECTION
Maintenance Display Item: ON
To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-214
Push Maintenance Display Items Push ESC and return to the former
On/Off. screen.
To the
next page
By changing the page,

the forward and
T1V7-05-03-069 T1V7-05-03-174 backward items are
Maintenance Setup Item Screen displayed.
T5-3-112
Push the displayed item and finally

push OK. Push All Sel and select
all the items.
To the
lower
T1V7-05-03-078 T1V7-05-03-080 T1V7-05-03-081
Display Item Selection Screen

Maintenance Setup Item Screen.
T1V7-05-03-082 T1V7-05-03-083 T1V7-05-03-084
T5-3-113
Maintenance Display Item: OFF

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041

To the
lower
T1V7-05-03-025 T1V7-05-03-042 T1V7-05-03-214

Push All Clr and all the selected
Push Maintenance Display Items Maintenance Display Items are
On/Off. turned into OFF.
To the
next page
By changing the page,

the forward and
T1V7-05-03-069 T1V7-05-03-174 backward items are
Maintenance Setup Item Screen displayed.
T5-3-114
Push the item of which the display

is turned into OFF and finally push Push ESC and return to
OK. Maintenance Setup Item Screen.
T1V7-05-03-173 T1V7-05-03-175 T1V7-05-03-172
Display Item Selection Screen
T5-3-115
FUEL CONSUMPTION GAUGE DISPLAY
ENABLE / DIABLE SELECTION
IMPORTANT: The valve on fuel gauge is reference
only and is not equal to autual valve.
Fuel Consumption Gauge Display: Enable
To the
lower
T1V7-05-03-001 T1V7-05-03-041
T1V7-05-03-009
push Fuel cost meter display
To the
lower
T1V7-05-03-025 T1V7-05-03-087
T1V7-05-03-042
Title Screen Various Setup Item Screen
Main Menu Screen
T1V7-05-03-088
T1V7-05-03-089

Screen, so that Fuel
Consumption Gauge Display
Enable is not set.
T5-3-116
Fuel Consumption Gauge Display: Disable

To the
lower
T1V7-05-03-001 T1V7-05-03-041
T1V7-05-03-009

push Fuel cost meter display
To the
lower
T1V7-05-03-025 T1V7-05-03-087
T1V7-05-03-042
Title Screen Various Setup Item Screen
Main Menu Screen
T1V7-05-03-090
T1V7-05-03-091

Screen, so that Fuel
Consumption Gauge Display
Disable is not set.
T5-3-117
PASSWORD CHANGE

To the
lower
T1V7-05-03-001 T1V7-05-03-009 T1V7-05-03-041
Input the registered password and Input the new password and push
Push Password. push OK. OK.
To the
lower
T1V7-05-03-025 T1V7-05-03-126 T1V7-05-03-127
Input the new password again and Push OK and return to Title
push OK. Screen.
T1V7-05-03-169 T1V7-05-03-128
T5-3-118
TROUBLESHOOTING / e-Shovel
OUTLINE
ICF (Information Controller) saves the input signals
from various sensors and switches of the machine as
data.
Various input signals are recorded as “list of daily
report data”, “list of frequency distribution data”, “list of
total operating hours”, “list of alarm” and “list of failure”
in ICF.
The recorded data is downloaded to the personal

computer and is uploaded to the center server via LAN,
so that the data can be used as “e-Service”.
The machine equipped with the optional satellite
communication terminal sends the data to center
server by using satellite communication. (As for the
satellite communication system, refer to T5-4-24.)
T5-4-1
LIST OF DAILY REPORT DATA
Data which can be downloaded by Dr. ZX (Palm)
Item Details
Date Date of daily report data
Time when key switch is first turned ON during a day
Start: Time
(Time is recorded by key switch ON signal.)
Time when key switch is last turned OFF during a day
Stop: Time
(Time is recorded by key switch ON signal.)
The value of the final remained fuel during a day
Fuel Level
(Value is recorded by fuel sensor data from monitor unit.)
The value of fuel used during a day
Fuel Usage Amount (Value is calculated and recorded by accumulated fuel usage amount
from ECM.)
Hour meter cumulative hours
Machine Hour Meter
(Hours are recorded by hour meter from monitor unit.)
Total engine operating hours selecting HP mode during a day
HP Mode Hours
(Hours are recorded by power mode switch information from MC.)
Engine Operating Total engine operating hours selecting P mode during a day
P Mode Hours
Hours (Hours are recorded by power mode switch information from MC.)
Total engine operating hours selecting E mode during a day
E Mode Hours
(Hours are recorded by power mode switch information from MC.)
Hours when auto-idle switch is turned ON during a day
Auto-Idle Switch ON Hours
(Hours are recorded by switch information from MC.)
Fast Idle (Hi) Total operating hours of travel mode (Hi) during a day
Travel Operating Traveling Hours (Hours are recorded by travel mode switch information from MC.)
Hours Slow Idle (Lo) Total operating hours of travel mode (Lo) during a day
Traveling Hours (Hours are recorded by travel mode switch information from MC.)
Total swing operating hours during a day
Swing Operating Hours
(Hours are recorded by swing pressure sensor information from MC.)
Total operating hours selecting front attachment during a day
Digging Operating Hours (Hours are recorded by front attachment pressure sensor information
from MC.)
Breaker Operating Total operating hours selecting breaker during a day
Hours (Hours are recorded by attachment information from MC.)
Secondary Crusher Total operating hours selecting secondary crusher during a day
Operating Hours (Hours are recorded by attachment information from MC.)
Attachment Primary Crusher Total operating hours selecting primary crusher during a day
Operating Hours Operating Hours (Hours are recorded by attachment information from MC.)
Vibrating Hammer Total operating hours selecting vibrating hammer during a day
Operating Hours (Hours are recorded by attachment information from MC.)
Bucket Operating Total operating hours selecting bucket during a day
Hours or Others (Hours are recorded by attachment information from MC.)
T5-4-2
Item Details
Total machine’s waiting hours during a day
No Load Hours
(Hours are recorded by each pressure sensor information from MC.)
The highest radiator coolant temperature during a day
Radiator Coolant Temperature
(Value is recorded from monitor unit.)
The highest hydraulic oil temperature during a day
Hydraulic Oil Temperature
(Value is recorded from MC.)
The highest intake-air temperature during a day
Intake-Air Temperature
(Value is recorded from ECM.)
Engine operating hour distribution during a day
Engine Operating Hour Distribution Data (Operating hours are recorded only when alternator output signal is
continuously delivered for more than 10 minutes.)
Machine operating hour distribution during a day
Loaded Hours Distribution Data (Operating hours are recorded only when operating pressure is
continuously detected for more than 5 minutes while the engine runs.)
NOTE: The daily operation in this table is
equivalent to the hours between 0:00 and
23:59:59 counted by the ICX built-in clock.
In case the engine is kept operated beyond
0:00, such data are recorded as those for
the following day.
T5-4-3
Data which can be sent by Satellite Communication

Item Details
Date Date of daily report data
The value of the final remained fuel during a day
Fuel Level
(Value is recorded by fuel sensor data from monitor unit.)
The value of fuel used during a day
Fuel Usage Amount (Value is calculated and recorded by accumulated fuel usage amount
from ECM.)
Hour meter cumulative hours
Machine Hour Meter
(Hours are recorded by hour meter from monitor unit.)
Total engine operating hours during daily operation
Engine Operating Hours
(Hours are recorded with alternator signal ON.)
Travel Operating Hours Total travel operating hours during daily operation
Swing Operating Hours Total swing operating hours during daily operation
Front Attachment Operating Hours Total front attachment and swig operating hours during daily operation
Attachment Operating Hours Total attachment operating hours during daily operation
No Load Hours Total machine’s waiting hours during daily operation
Radiator Coolant Temperature The highest radiator coolant temperature during a day
Hydraulic Oil Temperature The highest hydraulic oil temperature during a day
Intake-Air Temperature The highest intake-air temperature during a day
Engine Operating Hour Distribution Data Engine operating hour distribution during daily operation
(Operating hours are recorded only when alternator output signal is
continuously delivered for more than 10 minutes.)
Loaded Hour Distribution Data Machine operating hour distribution during daily operation
(Operating hours are recorded only when operating pressure is
continuously detected for more than 5 minutes while the engine runs.)
NOTE: The daily operation in this table is
equivalent to the hours between 0:00 and
23:59:59 counted by the ICX built-in clock.
In case the engine is kept operated beyond
0:00, such data are recorded as those for
the following day.
T5-4-4
LIST OF FREQUENCY DISTRIBUTION DATA
Item Details
Fuel Temperature Frequency distribution of fuel temperature
Frequency distribution of average pump delivery pressure of pumps 1
Pump Load
and 2
Average Pump Delivery Pressure in Frequency distribution of average delivery pressure from pumps during
Digging Operation digging operation
Average Pump Delivery Pressure in Frequency distribution of average delivery pressure from pumps during
Travel Operation travel operation
Radiator Coolant Temperature Frequency information of coolant temperature
Hydraulic Oil Temperature Frequency information of hydraulic oil temperature
Radiator Coolant Temperature － Frequency information on temperature in which intake air temperature is
Intake-Air Temperature pulled from coolant temperature
Hydraulic Oil Temperature － Intake-Air Frequency information on temperature in which intake air temperature is
Temperature pulled from hydraulic oil temperature
Frequency information of engine speed andaverage load rate (average
Pump Load Rate
of pump 1 load rate and pump 2 load rate)
Engine Load Rate Frequency information of engine spood and engine torque
Radiator Coolant Temperature/Intake-Air
Frequency information of coolant temperature and intake air temperature
Temperature
Hydraulic Oil Temperature/Intake-Air Frequency information of hydraulic oil temperature and intake air
Temperature temperature
T5-4-5
LIST OF TOTAL OPERATING HOURS
Item Details
Inner Hour Meter Hour meter’s value accumulated inside ICF
Machine Hour Meter Hour meter’s value accumulated in machine’s monitor
HP Mode Hours Total engine operating hours selecting HP mode
Engine Operating
P Mode Hours Total engine operating hours selecting P mode
Hour
E Mode Hours Total engine operating hours selecting E mode
Auto-Idle Switch ON Hours Hours when auto-idle switch is turned ON
Fast Idle (Hi)
Total operating hours of travel mode (Hi)
Travel Operating Traveling Hours
Hour Slow Idle (Lo)
Total operating hours of travel mode (Lo)
Traveling Hours
Swing Operating Hour Total swing operating hours during
Front Attachment Operating Hour Total front attachment and swig operating hours
Breaker Operating
Total operating hours selecting breaker during daily operation
Hours
Secondary Crusher Total operating hours selecting secondary crusher during daily
Operating Hours operation
Attachment Primary Crusher
Total operating hours selecting primary crusher during daily operation
Operating Hour Operating Hours
Vibrating Hammer Total operating hours selecting vibrating hammer during daily
Operating Hours operation
Bucket Operating
Total operating hours selecting bucket during daily operation
Hours or Others
No Load Hours Total machine’s waiting hours
T5-4-6
(Blank)
T5-4-7
HOW TO DOWNLOAD AND UPLOAD DATA ZX200-3 class, ZX240-3 class, ZX270-3 class
OF ICF
Rear Console
After the data saved in ICF is downloaded to Palm (Dr.
ZX), is uploaded to the personal computer, and is
uploaded to the center server by using LAN, the data
can be used as “e-Service”.
How to Download Data from Machine to Palm

1. Connect the Dr. ZX connectors in Palm (Dr. ZX)
and machine by using the Hot Sync cable and
connecting harness.
2. Turn Palm (Dr. ZX) ON and start downloading the
data. (Refer to the next page.)
Satellite ICF Dr. ZX
Terminal Connector
T1V1-05-07-001

Dr. ZX Connector
ICF T1V1-01-02-047
Palm
(Dr. ZX)
Hot Sync
Cable
Connecting
Harness
T1V1-05-07-002
T5-4-8
Data Download

Select Function Select failure-diagnosis
controller Password
+ Engine Controller To the
+ Select Controller Dr. ZX SerVice Soft lower
+ Main Controller (C)Hitachi Construction
Machinery Co., ltd
+ Monitor Controller
+ ICF Controller
Save Data Check
ESC ESC Start Back

While downloading data,

Push OK. Push Date Download. Download Screen is displayed.
Select Item Data Download
・ ICF + Information C/U: Various Downloading.

controller Ver.: XXYY Setup Do not turn off the Palm or To the
・ Satellite terminal Controller + Data Download disconnect the download lower
Ver.: XXYY cable.
Is it correct?
27%
OK ESC ESC Cancel
ICF Controller Screen Main Menu Screen Data Download Screen
When downloading is completed

normally, Normal End Screen is If pushing Cancel on Data
displayed. Download Screen, Alarm Screen
Push OK and return to Main Menu is displayed. Push OK and return Push ESC and return to Title
Screen. to Main Menu Screen. Screen.
Select Item
+ Information C/U: Various

CAUTION Setup
Initialization has been Initialization has been
completed. The completed. + Data Download
i The download is download has been
completed. interrupted.
You may disconnect the No data has been

download cable. transferred to the Dr. ZX
OK OK ESC
Normal End Screen Alarm Screen Main Menu Screen
T5-4-9
How to Upload Data from Palm (Dr. ZX) to
Personal Computer
1. Set Palm (Dr. ZX) to the cradle. Connect the USB

cable to the personal computer.
2. Push the Hot Sync button.
NOTE: When pushing the Hot Sync button and Palm (Dr. ZX)
uploading the data to the personal
computer, the Palm Desktop software
attached with (Dr. ZX) Palm need to be
installed.
Cradle
Hot Sync
Button
T178-05-07-033
T5-4-10
VARIOUS SETUP OF ICF AND SATELLITE
COMMUNICATION TERMINAL BY USING
Dr. ZX
Before starting satellite communication, installing the
satellite communication terminal and replacing ICF,
perform the following procedures by using Dr. ZX.
ICF Setup Procedures
Start Dr. ZX
1.1 Select Information Controller
1.2 Select Information C/U: Various Setup
1.3 Enter Date and Time
1.4 Enter Model and Serial No.
1.5 Information C/U: Initialize
Communication No Communication
1.6 Satellite Terminal: Initialize
1.7 Satellite Terminal Serial No. Check
1.8 Satellite Terminal, Communicating State Check
2. Self-Diagnosing
T5-4-11

Select Function Select failure-diagnosis Password

controller
+ Select Controller Dr. ZX SerVice Soft
lower
Machinery Co., ltd
+ ICF Controller
Save Data Check
ESC ESC Start Back

Push OK. Setup.
Select Item Select Item
・ ICF Information C/U: Various + Information C/U: Initialize

+
Controller Ver.: XXYY Setup
・ Satellite Terminal + Enter Model and Serial
+ Data Download
Controller Ver.: XXYY No.
+
Is it correct? Enter Date and Time
+
Control Data: Initialize
OK ESC ESC ESC
Screen
T5-4-12
1.3 Enter Date and Time
Push Set and the focused item is
YY.
Push Enter Date and Time. Push ESC and return to
Push ESC and return to Main Information C/U: Various Setup
Menu Screen. Screen.
Select Item Enter Date and Time

+ Information C/U: Initialize YY 2004 MM 01 DD 01 The focused item is displayed reversely.
At first, the focused item is YY.
+ Enter Model and Serial HH 01 MM 01
No.
+ Enter Date and Time
+ Control Data: Initialize
－＋ YY, MM, DD, HH and MM

Move the focused item.
ESC Set ESC No repeat input.
Information C/U: Various Setup Enter Date and Time Screen
Screen
－＋
Value of the focused item is increased or
decreased one by one.
In case value is beyond maximum one:
Select Item Change value into the minimum one
Information C/U: Various In case value is below minimum one: Change
+ value into the maximum one
Setup
No repeat input.
+ Data Download
ESC
Main Menu Screen
T5-4-13
1.4 Enter Model and Serial No.
Push Enter Model and Serial No.
Select Item
+ Information C/U: Initialize

Enter Model and Serial To the
+ lower
No.
ESC

Screen
After inputting model and serial

Push Exec, and model and serial No., push OK and return to Enter
No. can be input. Model and Serial No. Screen.
Push ESC and return to Push ESC and return to
Enter Model and Serial No. Enter Model and Serial No. Select Item
Model 01G6 + Information C/U: Initialize

Model |
Ex. Mach.No.(HCM1G600P12 Enter Model and Serial
3456) Model(01G6) +
Exec ESC No.
Serial No. 900005 Serial No.
ESC OK
Ex. Mach.No.(HCM1G600P12 + Control Data: Initialize
3456) Serial No.(123456)
Exec ESC OK ESC ESC
Enter Model and Serial No. Information C/U: Various Setup

Screen
T5-4-14
1.5 Information C/U: Initialize
Push Information C/U: Initialize.
Select Item
+ Enter Model and Serial To the

No. lower
ESC

Screen

operating data is initialized.
Push ESC and return to Push OK and return to
Information C/U: Various Setup Push ESC and return to Main
Information C/U: Various Setup Menu Screen.
Screen. Screen.
Information C/U: Initialize Select Item

Is operation data erased? Initialization has been
completed. + Enter Model and Serial
Init i Initialization has been No.
completed.
ESC
+ Control Data: initialize
Init ESC OK ESC
Information C/U: Initialize Screen Information C/U: Various Setup

Screen
T5-4-15
1.6 Satellite Terminal: Initialize
Push Exec.
Display the next screen of Push Satellite Terminal: Initialize. Push ESC and return to
Information C/U: Various Setup Push ESC and return to Main Information C/U: Various Setup
Screen. Menu Screen. Screen.
Select Item Select Item Satellite Terminal: Initialize
+ Information C/U: Initialize + Satellite Terminal:

Initialize
+ Enter Model and Serial Satellite Terminal No. To the
+ Is Un-Transmit data erased?
No. Confirmation lower
+ Enter Date and Time + Communicating State
Check
+ Control Data: Initialize + Enter Satellite Comm.
Start/Stop
ESC ESC Exec ESC
Information C/U: Various Setup Next Screen of Information C/U: Satellite Terminal: Initialize
Screen Various Setup Screen
Push OK and return to

Screen.
Satellite Terminal: Initialize Select Item Select Item
+ Satellite Terminal: + Information C/U: Various

Initialize Setup
Un-Transmit data is erased. Satellite Terminal No. Data Download
+ Confirmation +
+ Communicating State
Check
+ Enter Satellite Comm.
Start/Stop
OK ESC ESC
Information C/U: Various Setup Main Menu Screen

Screen
T5-4-16
1.7 Satellite Terminal Serial No. Check
Push Satellite Terminal No. Confirm serial no. (12 digits).
Confirmation. Push ESC and return to
Push ESC and return to Main Information C/U: Various Setup
Menu Screen. Screen.
Select Item Satellite Terminal No. Select Item

Confirmation
+ Satellite Terminal: + Satellite Terminal:
Initialize Initialize
+ Satellite Terminal No. + Satellite Terminal No.
Confirmation Confirmation
Serial No. 8GBDA701862
+ Communicating State + Communicating State
Check Check
+ Enter Satellite Comm. + Enter Satellite Comm.
Start/Stop Start/Stop
ESC ESC ESC
Information C/U: Various Setup Information C/U: Various Setup

Screen Screen
Select Item
+ Information C/U: Various

Setup
+ Data Download
ESC
Main Menu Screen
T5-4-17
1.8 Satellite Terminal, Communicating State
Check
Push Communicating State
Check.
Menu Screen. Check communicating state.
Select Item Communicating State Check
Satellite Terminal: ICF⇔Satellite Terminal Check the enclosed state.
+
Initialize ・ Conn Conn UnCon
Satellite Terminal No. Uncon: Faulty harness
+ ・ Comm. OK NG
Confirmation NG: Faulty harness for Comm.
Communicating State Satellite Terminal
+ OFF: Faulty harness, Faulty controller
Check ・ Power ON OFF
Stop: 1.9 Enter Satellite Comm. Start/Stop
+ Enter Satellite Comm. ・ Comm. Enable Stop
Start/Stop
ESC ESC
Information C/U: Various Setup Communicating State Check

Screen
Rod Aerial OK NG
When electrical wave of the satellite is
GPS Aerial OK NG caught, the items are turned into OK.
Wave State ON OFF IMPORTANT: Check this with the key of
machine ON in outdoor.
Un Transmit Data Number According to state of electrical
0 wave, it may take a little
longer time.
Last Transmitting Time
2004/07/01 13：50：00
ESC
+ Information C/U: Various + Satellite Terminal:

Setup Initialize
Data Download Satellite Terminal No.
+ + Confirmation
Check
Start/Stop
ESC ESC
Main Menu Screen Information C/U: Various Setup

Screen
T5-4-18
1.9 Enter Satellite Comm. Start/Stop
Push ▼ and move to the next
screen of Information C/U:
Various Setup Screen.
Push Enter Satellite Comm.
Start/Stop.
Select Item
+ Satellite Terminal:
Initialize
Satellite Terminal No. To the
+ lower
Confirmation
Check
Start/Stop
ESC

Screen
When starting Satellite Comm.,

push Start and push Exec.
When stopping Satellite Comm.,
push Stop and push Exec.
Information C/U: Various Setup Push ESC and return to Main
Screen. Menu Screen.
Screen.
Enter Satellite Comm. Start/Stop Satellite Terminal UnTrasmit Select Item
State
+ Satellite Terminal:
Initialize
+ Satellite Terminal No.
Exec Confirmation
Start Stop Setting has been completed + Communicating State
Check
ESC
Start/Stop
Exec ESC OK ESC

Screen
T5-4-19
1.10 Control Data: Initialize
Push Control Data: Initialize.
Select Item
+ Enter Model and Serial

No.
ESC

Screen

Control Data: Initialize Select Item

Is control data initialized? Initialization has been
completed.
ESC
Init ESC OK ESC

Screen
T5-4-20
(Blank)
T5-4-21
2. Self-Diagnosing
Push Fault of ICF Controller. If
After starting Dr. ZX, push there is no trouble, No Problem is
Self-Diagnostic Result. displayed.
Select Function Self-diagnosing of controllers

below hasn completed.
Engine Controller No Problem
+ To the
Select Controller
Main Controller Fault lower
Self-Diagnosing
Monitor Controller No Problem
ICF Controller Fault
ESC ESC ESC
Function Selection Screen Controller Self-Diagnosing Screen

Change the page and
the fault code in back
and forth is displayed.
Push Retry B and return to Controller
Push Details, and Details and Self-Diagnosing Screen after controller
Corrective Action are displayed. self-diagnsing.
Push ESC and Retry B Screen is Push ESC and Retry B Screen is Push ESC and return to Controller
displayed. displayed. Self-Diagnosing Screen.
ICF Controller Fault Code 14000-2
Problem was detected.
Details Retry B
14000 14001 Details CAN Communication Error
Do you want to escape?

Corrective Action
1)Retry B
ESC 2)Check Harness ESC
3)
ESC ESC Retry B ESC

Details
Fault Code Screen Retry B Screen
Self-diagnosing of controllers
below hasn completed.
Execute
Engine Controller No Problem
Retry B
Main Controller Fault
ESC Monitor Controller No Problem
ICF Controller Fault
ESC
Controller Self-Diagnosing Screen
T5-4-22
LIST OF FAULT CODE
Fault Code Details Remedy
14000-2 CAN Communication Error Execute retry B in self-diagnosing.

If this error code is displayed after re-try, check the following
item.
Check the CAN communication line (check the harness).
14001-2 ICF: Flash Memory: Read / Write Execute retry B in self-diagnosing and execute the following
Error item.
Execute 1.5 Information C/U: Initialize (T5-4-15).
14002-2 ICF: External RAM: Read / Write
Error
14003-2 ICF: EEPROM: Sum Check Error Execute retry B in self-diagnosing.

item.
1. Execute 1.10 Control Data: Initialize (T5-4-20).
2. Execute 1.4 Enter Model and Serial No. (T5-4-14).
Then, execute self-diagnosing and execute retry B.
14006-2 ICF: Satellite Communication Execute retry B in self-diagnosing.

Terminal: Communication Error If this error code is displayed after re-try, check the following
item.
Check the communication line.
Check the power source line of satellite terminal.
Check the fuse.
14008-2 ICF: Abnormal Internal RAM Execute retry B in self-diagnosing.

If this error code is displayed after re-try, replace the
14100-2 Satellite Communication Terminal: controller.
Abnormal EEPROM
14101-2 Satellite Communication Terminal:
Abnormal IB/OB Queue
14102-2 Satellite Communication Terminal: Check the communication aerial of satellite terminal.
Abnormal Local Loup Back
The satellite is not found.
14104-2 Satellite Communication Terminal: Execute retry B in self-diagnosing.
Fail 1 of Remote Loup Back If this error code is displayed after re-try, replace the
Fail 2 of Remote Loup Back
Sending and receiving data are
unmatched.
T5-4-23
SATELLITE COMMUNICATION SYSTEM GPS Aerial
The satellite communication system is used for Communication

maintenance of the machine, “e-Service” by Aerial
transmitting various data of the machine regularly via a
low earth orbit satellite.
NOTE: Depending on the circumstances of the

machine (ex. in the constructions, in the
tunnel, affected by the surrounding building
and affected of noise), the data transfer
rate may become slower, or the
communication might not be established.
The satellite communication system using
a low earth orbit satellite transmits digital T1V1-05-07-003
data through the radio wave. If there is ZX200-3 class, ZX240-3 class, ZX270-3 class
excessively noise or use of electrical
equipment which causes noise near the
machine, they cause reduces data transfer
rate or communication might not be
established at worst.
The satellite communication system consists of

satellite communication terminal, GPS aerial and
communication aerial. The mail function of monitor
unit becomes effective.
Satellite Terminal T1V1-05-07-001
The functions of each equipment are: ICF
• Satellite Communication Terminal
Receives the data from ICF, GPS aerial and Satellite Terminal
monitor unit, and sends the data to the
communication aerial.
• GPS Aerial
Receives location information of the machine
from a low earth orbit satellite.
• Communication Aerial
Communicates the data with a low earth orbit
satellite.
• Monitor Unit
Sends the mail when pushing the key
corresponding to requirement.
1. General Requirement Monitor Unit ICF T1V1-01-02-047
2. Fuel Replenishing Requirement

3. Service Maintenance Requirement
4. Forwarding Requirement
1 2 3 Mail Screen 4 T1V5-05-01-037
T5-4-24
On the machine equipped with the satellite
communication system, the data are sent according to
the condition as follows:
Data Type sent from the machine by using satellite

communication:
Items Data Type Condition
Periodical Daily Report Data, Latest LocationThe data are sent once a day. In order to
Transmission Information, Fuel Level avoid congested traffic in the
communication line, the data is sent
randomly between 0:00 and 02:00.
Transmitting Data at Latest Location Information The data is sent only when the machine
Engine Start is moved more than 5 km from the place
where it is recorded last time.
Emergency Alarm and Error Information The transmission starts immediately
Transmission when the alarm and error occurs.
Hour Meter 100 Hours Frequency Distribution Information The data is sent when the hour meter
Transmission exceeds every 100 hours.
Transmission by Mail General Requirement, Fuel Replenishing The transmission starts when the key on
Requirement, Service Maintenance monitor unit corresponding to
Requirement and Forwarding requirement is pushed.
Requirement
T5-4-25
(Blank)
T5-4-26
TROUBLESHOOTING / Component Layout
MAIN COMPONENTS
ZX200-3 class, ZX240-3 class, ZX270-3 class
1 3
24
4 5 6
7
8
9
23
22 10
11
21
20 12
19 13
14
18 17 16 15 T1V1-01-02-013
1- Bucket Cylinder 7 - Fuel Tank 13 - Intercooler 19 - Fuel Cooler

2- Arm Cylinder 8 - Hydraulic 14 - Air Conditioner Condenser 20 - Air Cleaner
Oil Tank
3- Boom Cylinder 9 - Control Valve 15 - Radiator 21 - Signal Control Valve
4- Center Joint 10 - Pilot Filter/ Pilot Relief 16 - Battery 22 - Pilot Shut-Off Solenoid
Valve Valve
5- Swing Bearing 11 - Pump Device 17 - Travel Device 23 - Travel Pilot Valve
6- Swing Device 12 - Engine 18 - Oil Cooler 24 - Front Attachment / Swing
Pilot Valve
T5-5-1
ZX225US-3class, ZX225USR-3 class
1
2
3
4
5
6
7
8
9
10
11
22
12
21
13
20 14
19 15
18
17
16
1V1-01-02-031
1- Bucket Cylinder 7 - Fuel Tank 13 - Radiator 18 - Fuel Cooler

2- Arm Cylinder 8 - Hydraulic 14 - Intercooler 19 - Oil Cooler
Oil Tank
3- Boom Cylinder 9 - Swing Device 15 - Air Conditioner 20 - Front Attachment/ Swing Pilot
Condenser Valve
4- Signal Control Valve 10 - Pump Device 16 - Battery 21 - Pilot Shut-Off Solenoid Valve
5- Control Valve 11 - Engine 17 - Air Cleaner 22 - Travel Pilot Valve
6- Solenoid Valve Unit 12 - Center Joint
T5-5-2
Front Attachment (2-Piece Boom)
3
4 5 6
2
7
11
T1V1-01-02-006
10
1- Bucket 4 - Hose Rupture Valve (Arm 7- Hose Rupture Valve 10 - Hose Rupture Valve (Boom
Cylinder) (Positioning Cylinder) Cylinder)
2- Bucket Cylinder 5 - Arm Cylinder 8 - Positioning Cylinder 11 - Boom Cylinder
3- Arm 6 - Upper Boom 9 - Bottom Boom
T5-5-3
ELECTRICAL SYSTEM (OVERVIEW)
Engine
ZX200-3 class, ZX240-3 class, ZX270-3 class • Cam Angle Sensor
• Crank Speed Sensor
• Engine Oil Pressure Sensor
• Coolant Temperature Sensor
• Fuel Temperature Sensor
• Boost Temperature Sensor
Pump Device • Boost Pressure Sensor
1
• Pump 1,2 Delivery Pressure • Common Rail Pressure
Sensors Sensor
• Pumps 1, 2 Control Pressure • Overheat Switch
Sensors • Supply Pump Actuator
• Torque Control Solenoid Valve • EGR Valve
• Maximum Pump 2 Flow Rate • Injector
Limit Control Solenoid Valve • Glow Plug
Refer to T1-2-9. 14
Refer toT1-2-8.
13 Electrical System
Control Valve. (Relays)
• Pressure Sensor • Fresh Air
(Arm Roll-In) Temperature
• Pressure Sensor Sensor
(Boom Raise) • Starter Relay 2
Refer to T1-2-10. • Battery Relay
• Glow Relay
• Fusible Link
12 Refer to T1-2-7.
11
Swing Device Electrical System

• Pressure Sensor (Around Air Cleaner)
(Front Attachment) • ECM
Refer to T1-2-9. • Atmospheric Pressure
Sensor
10 • Intake-Air Temperature
4
Sensor
9 Refer to T1-2-7.
5
8
Signal Control Valve

T1V1-01-02-022
• Pressure Sensor
7 (Travel)
6 • Pressure Sensor
(Swing)
Refer to T1-2-10.
1- Rear View Camera 5- GPS (Global Positioning 9- Positioning Control Valve 12 - Hydraulic Oil Temperature
System) Aerial (2-Piece Boom Machine Sensor
Only)
2- Battery 6- Wiper Motor 10 - Working Light 13 - Solenoid Valve Unit
3- Communication Aerial 7- Monitor Unit 11 - Fuel Sensor 14 - Solenoid Pump
4- Air Filter Restriction 8- Horn
Switch
T5-5-4
ZX225US-3 class, ZX225USR-3 class Engine
• Cam Angle Sensor • Overheat Switch
• Crank Speed Sensor • Supply Pump Actuator
• Engine Oil Pressure Sensor • EGR Valve
Pump Device • Coolant temperature sensor • Injector
• Pump 1,2 Delivery Pressure • Fuel Temperature Sensor • Glow Plug
Sensors • Boost Temperature Sensor
• Pumps 1, 2 Control Pressure • Boost Pressure Sensor
Sensors • Common Rail Pressure Electrical System
• Torque Control Solenoid Valve Sensor (Relays)
1 2 (Refer to T1-2-13.)
• Maximum Pump 2 Flow Rate • Fresh Air
Limit Control Solenoid Valve 3 Temperature
(Refer to T1-2-14.) Sensor
14 • Starter Relay 2
Swing Device • Battery Relay
• Pressure Sensor • Glow Relay
(Front Attachment) • Fusible Link
(Refer to T1-2-15.) (Refer to T1-2-12.)
13
Electrical System
12 (Around Air Cleaner)
• Atmospheric Pressure
Sensor
• Intake-Air Temperature
Sensor
(Refer to T1-2-11.)
11
Signal Control Valve

• Pressure Sensor (Travel) 5
10
• Pressure Sensor (Swing)
(Refer to T1-2-16.)
9 6
7
Control Valve 8
• Pressure Sensor (Arm Roll-In)
• Pressure Sensor (Boom Raise) T1V1-01-02-033
(Refer to T1-2-16.)
1- GPS (Global Positioning 5 - Battery 9 - Monitor Unit 12 - Solenoid Valve Unit

System) Aerial
2 - Communication Aerial 6 - ECM (Engine Control Module) 10 - Horn 13 - Fuel Sensor
3 - Rear View Camera 7 - MC (Main Controller) 11 - Working Light 14 - Hydraulic Oil Temperature
Sensor
4- Air Filter Restriction 8 - Wiper Motor
Switch
T5-5-5
ELECTRICAL SYSTEM (IN CAB)
Rear Tray
Refer to T1-2-8.
Switch Panel
Refer to T1-2-10.
T1V1-01-02-011
1
1- Engine Stop Switch 2- Radio
T5-5-6
Rear Tray
(Refer to T1-2-9.)
Switch Panel
(Refer to T1-2-10.)
1 T1V1-01-02-034
1 - Engine Stop Switch 2- Radio
T5-5-7
ELECTRICAL SYSTEM (REAR TRAY)
ZX200-3 class, ZX240-3 class, ZX270-3 class 1
T1V1-01-02-007
5 4
8 9 10 11
7
12
6
13
14
T1V1-01-02-009
19 18 17 16 15
1- MC (Main Controller) 6- Starter Relay 2 (R5) 11 - Pilot Shut-Off Relay (R12) 16 - Light Relay 2 (R8)
2- Fuse Box 7- Starter Cut Relay (R4) 12 - Load Damp Relay (R1) 17 - ECM (Engine Control
Module) Main Relay (R14)
3- Dr. ZX Connector 8- OFF Relay (Air 13 - Wiper Relay (R6) 18 - Washer Relay (R9)
(Download Connector Conditioner) (R12)
Using Combinedly)
4 - ICF (Information 9- Security Horn Relay (R3) 14 - Light Relay 1 (R7) 19 - Horn Relay (R10)
Controller)
5 - Satellite Communication 10 - Air Conditioner Relay 15 - MAX HI Relay (Air
Terminal (Optional) (R11) Conditioner) (R13)
T5-5-8
T1V1-01-02-035
18
5
17
6
16
7
15
8
14
9
13
10
12 11
T1V1-01-02-036
1- Satellite Communication 6 - Light Relay 1 (R7) 11 - Horn Relay (R10) 15 - Security Horn Relay (R3)
Terminal (Optional)
2 - Dr. ZX Connector (Download 7 - MAX HI Relay (Air 12 - Starter Relay 2 (R5) 16 - Air Conditioner Relay (R11)
Connector Using Combinedly) Conditioner) (R13)
3 - Fuse Box 8 - Light Relay 2 (R8) 13 - Starter Cut Relay (R4) 17 - Pilot Shut-Off Relay (R2)
4 - ICF (Information Controller) 9 - ECM (Engine Control 14 - OFF Relay (Air 18 - Load Damp Relay (R1)
Module) Main Relay Conditioner) (R12)
(R14)
5- Wiper Relay (R6) 10 - Washer Relay (R9)
T5-5-9
ELECTRICAL SYSTEM (SWITCH PANEL)
5
2
1
6
9 8 7 T1V1-01-02-037
1 - Wiper / Washer Switch 4 - Auto-Idle Switch 6- Travel Mode Switch 8- Overhead Window Washer
Switch (Optional)
2 - Working Light Switch 5 - Power Mode Switch 7- Key Switch 9 - Overhead Window Wiper Switch
(Optional)
3 - Engine Control Dial
T5-5-10
ELECTRICAL SYSTEM (AROUND AIR CLEANER)
Machine Front
Machine Front 3
Air Cleaner
2
T1V1-01-02-023 T1V1-01-02-012
Air Cleaner

Overhead Window Washer Tank
(only ZAXIS225USRK-3)
Air Cleaner
T1V1-01-02-038
1- ECM (Engine Control Module) 2- Atmospheric Pressure 3- Intake-Air Temperature

Sensor Sensor
T5-5-11
ELECTRICAL SYSTEM (RELAYS)
T1V1-01-02-018
1- Fresh Air Temperature 3 - Battery Relay 4- Glow Relay 5- Fusible Link

Sensor
2 - Starter Relay 2
T5-5-12
ENGINE
3 4 5
1
T1V1-01-02-017
T1V1-01-02-016
8 7
9 10 11 12 9
T1V1-01-02-015
13
1- Cam Angle Sensor 5- Fuel Temperature Sensor 8- Hydraulic Oil Pressure 11 - Boost Temperature Sensor
Sensor
2- Overheat Switch 6- Crank Speed Sensor 9 - Injector 12 - Boost Pressure Sensor
3- Coolant temperature 7- Supply Pump Actuator 10 - EGR (Exhaust Gas 13 - Glow Plug
sensor Recirculation) Valve
4 - Common Rail Pressure
Sensor
T5-5-13
PUMP DEVICE
8
1 2 3
5 4 T1V1-01-02-032
T1V1-04-05-002
AROUND PUMP DEVICE

(ZX225US-3 class, ZX225USR-3 class)
10
11 T1V1-01-02-039
1- Pilot Pump 4 - Pump 1 Delivery Pressure 7 - Maximum Pump 2 Flow 10 - Solenoid Pump
Sensor Rate Limit Control
Solenoid Valve
2- Pump 2 5 - Pump 2 Delivery Pressure 8 - Pump 2 Control Pressure 11 - Pilot Filter/ Pilot Relief
Sensor Sensor Valve
3- Pump 1 6 - Torque Control Solenoid 9 - Pump 1 Control Pressure
Valve Sensor
T5-5-14
SWING DEVICE
ZX200-3 class, ZX225US-3 class, ZX270-3 class
ZX225USR-3 class, ZX240-3 class
Machine Front
2 T1V1-01-02-004
T1V1-01-02-005
1 - Swing Relief Valve 2- Pressure Sensor (Front

Attachment)
T5-5-15
CONTROL VALVE
1
Main Relief Valve
T1V1-03-03-073
SIGNAL CONTROL VALVE
T1V1-01-02-014
1- Pressure Sensor (Arm 2- Pressure Sensor (Boom 3- Pressure Sensor (Swing) 4- Pressure Sensor (Travel)
Roll-In) Raise)
T5-5-16
SOLENOID VALVE UNIT
1 2 3 4
T1V1-03-07-007
TRAVEL DEVICE ZX270-3 class

ZX200-3 class, ZX225US-3 class,
ZX225USR-3 class, ZX240-3 class
5
5 5
T1HD-01-02-001
T178-01-02-014
1- Solenoid Valve Unit SC 3- Solenoid Valve Unit SI 5- Counterbalance Valve 6 - Travel Relief Valve
2- Solenoid Valve Unit SF 4- Solenoid Valve Unit SG
T5-5-17
LAYOUT OF ATTACHMENT SPEC. PARTS
Boom Upper Side

• Accumulator Control Valve
• Accumulator (High Pressure)
• Accumulator (Low Pressure)
(Refer to T1-2-23.)
Secondary Pilot Relief

Pressure Valve
(Refer to T1-2-21.)

Pressure Control Valve
(Refer to T1-2-21.)
Selector Valve
(Refer to T1-2-21.)
Pilot Valve (Auxiliary)
Utility Space
• Selector Valve Control
Solenoid Valve
• Secondary Pilot Relief
Pressure Control Solenoid
Valve
• Accumulator Control T1V1-01-02-024
Solenoid Valve
• Pressure Sensor (Auxiliary)
• Auxiliary Flow Combining
Solenoid Valve
• Auxiliary Flow Rate Control
Solenoid Valve
• Pressure reducing valve:
• Accumulator (pilot Circuit)
• Check Valve
(Refer to T1-2-22.)
T5-5-18

Pressure Control Valve
Selector Valve
T1V1-01-02-026
Swing Device
Control Valve
Pressure Valve Boom
T1V1-01-02-025
Center Joint T1V1-01-02-027
T5-5-19
Utility Space
2 3
4
1
6
7
T1V1-01-02-028
T1V1-01-02-029
1- Selector Valve Control 4 - Pressure Sensor 6- Auxiliary Flow Rate Control 8- Accumulator (Pilot Circuit)
Solenoid Valve (Auxiliary) Solenoid Valve
2 - Secondary Pilot Relief 5 - Auxiliary Flow 7 - Pressure Reducing Valve: 9- Check Valve
Pressure Control Solenoid Combining Solenoid
Valve Valve
3 - Accumulator Control
Solenoid Valve
T5-5-20
Boom Upper Side
Accumulator
(Low Pressure)
Accumulator
(High Pressure)
Accumulator
Control Valve
T1V1-01-02-030
T5-5-21
Boom Upper Side

• Accumulator Control
Valve
• Accumulator (High
Pressure)
• Accumulator (Low
Pressure)
(Refer to T1-2-27.)
Selector Valve
Secondary Pilot Relief (Refer to T1-2-25.)
Pressure Valve
(Refer to T1-2-25.) Secondary Pilot
Relief Pressure
Control Valve
(Refer to T1-2-25.)
Pilot Valve (Auxiliary)
Swing Device Left Side

• Selector Valve Control Solenoid
Valve
• Secondary Pilot Relief Pressure
Control Solenoid Valve
• Accumulator Control Solenoid
Valve T1V1-01-02-046
• Pressure Sensor (Auxiliary)

• Auxiliary Flow Combining
Solenoid Valve
• Auxiliary Flow Rate Control
Solenoid Valve
• Pressure Reducing Valve:
• Accumulator (Pilot Circuit)
• Check Valve
(Refer to T1-2-26.)
T5-5-22
Selector Valve
Fuel Tank
Solenoid Valve
Unit
T1V1-01-02-040
Secondary Pilot
Relief Pressure
Control Valve
Machine Front Swing

Device
T1V1-01-02-042
Pressure Valve
Center Joint
Machine Front
T1V1-01-02-041
T5-5-23
Swing Device Left Side
1 2 3
6
7
Swing
Device
T1V1-01-02-043
8
Swing
Device
9
T1V1-01-02-044
1- Selector Valve Control 4 - Pressure Sensor 6- Auxiliary Flow Rate Control 8- Check Valve
Solenoid Valve (Auxiliary) Solenoid Valve
2 - Secondary Pilot Relief 5 - Auxiliary Flow 7 - Pressure reducing valve: 9- Accumulator (Pilot Circuit)
Pressure Control Solenoid Combining Solenoid
Valve Valve
3 - Accumulator Control
Solenoid Valve
T5-5-24
Boom Upper Side
Accumulator
(Low Pressure)
Accumulator Accumulator
Control Valve (High Pressure)
T1V1-01-02-045
T5-5-25
Layout of Control Valve
Machine Lower Machine Upper Machine Upper Machine Lower
1 2 3 4 5 6 7 8 9 10 11
12
42
13
14
41
40 15
16
39
17
38
18
19
20
37
36
35 21
34
22
23
33
32 24
31 30 29 28 27 26 25
T1V1-03-03-021
T5-5-26
4-Spool Section
Arm Roll-In
Pressure Sensor 18 19, 22 13
10, 11
23
15, 17
16
7
Boom Raise T1V1-03-03-073

Pressure Sensor 20 14
1- Load Check Valve (Left 12 - Bucket Regenerative Valve 23 - Arm 2 Flow Rate Control 34 - Arm Anti-Drift Valve
Travel Parallel Circuit) Valve (Switch Valve) (Switch Valve)
2 - Check Valve (Main 13 - Overload Relief Valve 24 - Load Check Valve (Arm 2 35 - Overload Relief Valve
Relief Circuit) (Bucket: Rod Side) Tandem Circuit) (Arm: Bottom Side)
3 - Main Relief Valve 14 - Overload Relief Valve 25 - Bypass Shut-Out Valve 36 - Arm Anti-Drift Valve
(Bucket: Bottom Side) (Check Valve)
4- Check Valve (Auxiliary 15 - Boom Flow Control Valve 26 - Arm 2 Flow Rate Control 37 - Overload Relief Valve
Combining Valve Circuit) (Poppet Valve) Valve (Poppet Valve) (Arm: Rod Side)
5 - Auxiliary Flow Combiner 16 - Boom Lower Meter-In Cut 27 - Arm Regenerative Valve 38 - Check Valve (Digging
Valve Valve Regenerative Circuit)
6 - Check Valve (Flow 17 - Boom Flow Rate Control 28 - Digging Regenerative 39 - Load Check Valve (Boom
Combiner Valve Circuit) Valve (Switch Valve) Valve 2 Parallel Circuit)
7 - Flow Combiner Valve 18 - Overload Relief Valve (Boom: 29 - Load Check Valve (Digging 40 - Auxiliary Flow Rate Control
Bottom Side) Regenerative Circuit) Valve (Poppet Valve)
8- Load Check Valve 19 - Boom Anti-Drift Valve (Check 30 - Arm 1 Flow Rate Control 41 - Auxiliary Flow Rate Control
(Orifice) (Bucket) Valve) Valve (Poppet Valve) Valve (Switch Valve)
9 - Check Valve (Main 20 - Overload Relief Valve (Boom: 31 - Load Check Valve (Swing 42 - Load Check Valve (Left
Relief Circuit) Rod Side) Circuit) Travel Tandem Circuit)
10 - Bucket Flow Rate 21 - Boom Regenerative Valve 32 - Arm 1 Flow Rate Control
Control Valve (Poppet Valve (Switch Valve)
Valve)
11 - Bucket Flow Rate 22 - Boom Anti-Drift Valve (Switch 33 - Load Check Valve (Arm
Control Valve (Switch Valve) Regenerative Circuit)
Valve)
T5-5-27
1 2 3 4 5 6 7 8 9 10 11
12
42
13
14
41
40 15
16
39
17
38
18
19
20
37
36
35 21
34
22
23
33
32 24
31 30 29 28 27 26 25
T1V1-03-03-021
T5-5-28
5-Spool Section
3
37 34, 36
30, 32
40, 41 T1V1-03-03-072
28
35
Valve)
Valve)
T5-5-29
1 2 3 4 5 6 7 8 9 10 11
12
42
13
14
41
40 15
16
39
17
38
18
19
20
37
36
35 21
34
22
23
33
32 24
31 30 29 28 27 26 25
T1V1-03-03-021
T5-5-30
3
A B
Cross Section C-C
C C
D D
E E
F F 4
G G
H H
I I
5
J J
7
T1V1-03-03-026 T1V1-03-03-003
A B
Cross Section A-A Cross Section B-B

3 2
9
12
28
21
27
29
T1V1-03-03-001 T1V1-03-03-002
Valve)
Valve)
T5-5-31
Machine Lower Machine Upper Machine Lower

Machine Upper
1 2 3 4 5 6 7 8 9 10 11
12
42
13
14
41
40 15
16
39
17
38
18
19
20
37
36
35 21
34
22
23
33
32 24
31 30 29 28 27 26 25
T1V1-03-03-021
T5-5-32
Cross Section D-D Cross Section E-E

Travel (left) Travel (right) Auxiliary Bucket
13
10
41
11
14
40
T1V1-03-03-005
T1V1-03-03-004 12
Valve)
Valve)
T5-5-33
1 2 3 4 5 6 7 8 9 10 11
12
42
13
14
41
40 15
16
39
17
38
18
19
20
37
36
35 21
34
22
23
33
32 24
31 30 29 28 27 26 25
T1V1-03-03-021
T5-5-34
Cross Section F-F Cross Section G-G

Boom 2 Boom 1 22 37
19
39
16
17
15
38 28 26
21 20
T1V1-03-03-006 T1V1-03-03-007
Valve)
Valve)
T5-5-35
1 2 3 4 5 6 7 8 9 10 11
12
42
13
14
41
40 15
16
39
17
38
18
19
20
37
36
35 21
34
22
23
33
32 24
31 30 29 28 27 26 25
T1V1-03-03-021
T5-5-36
Cross Section H-H Cross Section I-I

Arm 2 Swing
Arm 1
34
18
27
36
32 24
31
23
30
35 T1V1-03-03-009
T1V1-03-03-008
Valve)
Valve)
T5-5-37
1 2 3 4 5 6 7 8 9 10 11
12
42
13
14
41
40 15
16
39
17
38
18
19
20
37
36
35 21
34
22
23
33
32 24
31 30 29 28 27 26 25
T1V1-03-03-021
T5-5-38
Cross Section J-J

25
K K
L L
M M
T1V1-03-03-010
T1V1-03-03-027
Cross Section K-K
Cross Section L-L
8 6
N N
Cross Section M-M Cross Section N-N

42 Bo
T1V1-03-03-028
T1V1-03-03-022
1 - Load Check Valve (Left 23 - Bucket Regenerative Valve 34 - Arm 2 Flow Rate Control 43 - Arm Anti-Drift Valve
4 - Check Valve (Auxiliary 26 - Boom Flow Control Valve 37 - Arm 2 Flow Rate Control 46 - Overload Relief Valve
6 - Check Valve (Flow 28 - Boom Flow Control Valve 39 - Digging Generative Valve 48 - Load Check Valve (Boom
Combiner Valve Circuit) (Switch Valve) 2 Parallel Circuit)
8 - Load Check Valve 30 - Boom Anti-Drift Valve (Check 41 - Arm 1 Flow Rate Control 50 - Auxiliary Flow Rate Control
Valve)
Valve)
T5-5-39
Layout of Positioning Control Valve (2-Piece Boom)
4
3
T1V1-03-03-019
T5-5-40
X Cross Section X-X

2
3
T178-03-03-070
X T198-03-03-003
1- Load Check Valve 2- Overload Relief Valve 3- Overload Relief Valve 4- Load Check Valve
(Positioning Tandem Circuit) (Positioning: Rod Side) (Positioning: Bottom Side) (Positioning Parallel Circuit)
T5-5-41
PILOT PORT (Signal Control Valve)
Pilot Valve Side

PH
C
A
E
M
D
H
B
F
SB
PI G
Pilot Valve Side
K N
I
SH
J
DF
SA L
T178-03-06-016
T5-5-42
Pilot Valve Side

Port Name Connecting to Remark
Port A Right Pilot Valve Boom Raise Pilot Pressure
Port B Right Pilot Valve Boom Lower Pilot Pressure
Port C Left Pilot Valve Arm Roll-Out Pilot Pressure
Port D Left Pilot Valve Arm Roll-In Pilot Pressure
Port E Left Pilot Valve Left Swing Pilot Pressure
Port F Left Pilot Valve Right Swing Pilot Pressure
Port G Right Pilot Valve Bucket Roll-In Pilot Pressure
Port H Right Pilot Valve Bucket Roll-Out Pilot Pressure
Port I Travel Pilot Valve Left Travel Forward Pilot Pressure
Port J Travel Pilot Valve Left Travel Reverse Pilot Pressure
Port K Travel Pilot Valve Right Travel Forward Pilot Pressure
Port L Travel Pilot Valve Right Travel Reverse Pilot Pressure
Port M Auxiliary Pilot Valve Auxiliary Open Pilot Pressure
Port N Auxiliary Pilot Valve Auxiliary Close Pilot Pressure
Port SA Pump 1 Regulator Pump 1 Control Pressure
Port SB Pump 2 Regulator Pump 2 Control Pressure
Port PI Pilot Shut-Off Valve Primary Pilot Pressure
Port PH - Plug
Port SH Swing Parking Brake Brake Release Pressure
Port DF Hydraulic Oil Tank Returning to Hydraulic Oil Tank
T5-5-43
Control Valve Side

SM
3
1 5
13
2 4
SK
SE
Pressure Sensor (Swing)

8
14
Control Valve Side
7
9
6
10
SN
SL
11
Pressure Sensor (Travel) 12 SP T178-03-06-015
T5-5-44
Control Valve Side

Port Name Connecting to Remark
Port 1 Control Valve Boom Raise Pilot Pressure
Port 2 Control Valve Boom Lower Pilot Pressure
Port 3 Control Valve Arm Roll-Out Pilot Pressure
Port 4 Control Valve Arm Roll-In Pilot Pressure
Port 5 Control Valve Left Swing Pilot Pressure
Port 6 Control Valve Right Swing Pilot Pressure
Port 7 Control Valve Bucket Roll-In Pilot Pressure
Port 8 Control Valve Bucket Roll-Out Pilot Pressure
Port 9 Control Valve Left Travel Forward Pilot Pressure
Port 10 Control Valve Left Travel Reverse Pilot Pressure
Port 11 Control Valve Right Travel Forward Pilot Pressure
Port 12 Control Valve Right Travel Reverse Pilot Pressure
Port 13 Control Valve Auxiliary Open Pilot Pressure
Port 14 Control Valve Auxiliary Close Pilot Pressure
Port SE Control Valve Arm 1 Flow Rate Control Valve Control Pressure
Port SM Hydraulic Oil Tank Returning to Hydraulic Oil Tank
Port SN - Plug
Port SP Hydraulic Oil Tank Returning to Hydraulic Oil Tank
Port SL Control Valve Flow Combiner Valve Control Pressure
Port SK Control Valve Bucket Flow Rate Control Valve Control Pressure
2-Piece Boom Specification Machine

Port SP Positioning Pilot Valve Secondary Pilot Pressure
Machine with Front Attachment (Secondary Crushers 1 to 5 and Hydraulic Crushers 1 to 5) attached.
Port SM Auxiliary Flow Rate Combiner Solenoid Valve Auxiliary Flow Rate Combiner Valve Control
Pressure
Port SN Auxiliary Flow Rate Combiner Control Valve Auxiliary Flow Rate Combiner Valve Control
Pressure
Port SP Auxiliary Flow Rate Combiner Solenoid Valve Pump 1 Control Pressure
T5-5-45
(Blank)
T5-5-46
TROUBLESHOOTING / Troubleshooting A
TROUBLESHOOTING A PROCEDURE
Refer to troubleshooting A procedure in case any fault
codes are displayed after diagnosing by using Dr. ZX
or the service menu of monitor unit.
• How to Read Troubleshooting Flow Charts
YES(OK)
(2)
After completing the checking and/or measuring procedures in box (1),
・ (1) select YES (OK) or NO (NOT OK) and proceed to box (2) or (3).
(3)
NO(NOT OK)
Instructions, reference, and/or inspection methods and/or measurements are occasionally

・
described under the box. If incorrectly checked or measured, not only will troubleshooting
· Key switch: ON be unsuccessful but also damage to the components may result.
・ Refer to “Electrical System Inspection” Group (Group 8) for descriptions in the dotted-line
box.
・ Use Dr. ZX for descriptions in the double-line box.
・ Causes of machine problems are stated in the thick-line box. Scanning quickly through the
thick-line boxes allows you to estimate the possible causes before actually following the
flow chart.
NOTE: Harness end connector viewed from the

open end side by the all connectors image
shown in this section.
Harness
Open End
Side
Harness End Connector
T158-05-03-001
T5-6-1
FAULT CODE LIST
MC
Controller Hardware Failure
Fault Trouble Cause Influenced Control
Code
11000-2 Abnormal EEPROM Faulty MC All Control
11001-2 Abnormal RAM Faulty MC All Control
11002-2 Abnormal A/D Conversion Faulty MC All Control
11003-3 Abnormal Sensor Voltage Faulty MC All Control
11004-2 Abnormal CAN Communication Faulty MC • Heater Control

• Speed Sensing Control
• Attachment Operation Speed
Increase Control
Limit Control
• Attachment Pump Torque
Decrease Control
• Pump 1 Flow Rate Limit Con-
trol
trol
• Attachment Flow Rate Control
(Optional)
• Attachment Valve Selection
(Optional)
• CAN Cycle Data Communica-
tion
T5-6-2
Symptoms in Machine Opera- Remedy for Dr. ZX Remark

tion When Trouble Occurs.
- Retrial B Replace MC
Although the engine control dial Retrial B • Check sensor connected to
is operated, engine speed does MC
not change. • Check Harness
• Replace MC
• Machine movement is slow. Retrial B • Check CAN Harness
• The work mode alarm is dis- • Replace MC
played on the monitor unit.
T1V1-05-01-102
T5-6-3
Engine Failure
Code
11100-2 Abnormal Engine Speed Engine Speed: more than 4000 Speed Sensing Control
-1
min
11101-3 Abnormal Engine Control Dial Voltage: 4.78 V or higher Engine Control Dial Control
Sensor High Voltage
11101-4 Abnormal Engine Control Dial Voltage: Less than 0.22 V Engine Control Dial Control
Sensor Low Voltage
T5-6-4

Machine movement is slow. Retrial B • Check Crank Speed Sensor
(During speed sensing, torque • Check Cam Angle Sensor
is reduced.)
• Trouble condition with the Retrial B • Check Harness
key ON: Engine speed is kept • Replace Engine Control Dial
at idle speed.
• Trouble condition with the
key ON: engine speed is kept
at speed immediately before
trouble.
• Trouble condition with the Retrial B • Check Harness
key ON: Engine speed is kept • Replace Engine Control Dial
at idle speed.
• Trouble condition with the
key ON: engine speed is kept
at speed immediately before
trouble.
T5-6-5
Pump Failure
Code
11200-3 Abnormal Pump 1 Delivery Voltage: 4.5 V or higher • HP Mode Control
Pressure Sensor High Volt- • Travel HP Mode Control
age • E Mode Control
• Travel Torque-Up Control
• Arm Regenerative Control
• Digging Regenerative Control
• Auto-Power Lift Control
• Travel Motor Swash Angle Control
11200-4 Abnormal Pump 1 Delivery Voltage: Less than 0.25 V • HP Mode Control
Pressure Sensor Low Voltage • Travel HP Mode Control
• E Mode Control
Pressure Sensor High Volt- • Travel HP Mode Control
age • E Mode Control
• E Mode Control
11206-3 Abnormal Pump 1 Pump Voltage: 4.75 V or higher • E Mode Control
Control Pressure Sensor High • Heater Control
Voltage • Travel Motor Swash Angle Control
11206-4 Abnormal Pump 1 Pump Voltage: Less than 0.25 V • E Mode Control
Control Pressure Sensor Low • Heater Control
11208-3 Abnormal Pump 2 Pump Voltage: 4.75 V or higher • E Mode Control

Control Pressure Sensor High • Heater Control
11208-4 Abnormal Pump 2 Pump Voltage: Less than 0.25 V • E Mode Control
Control Pressure Sensor Low • Heater Control
T5-6-6
Symptoms in Machine Operation When Remedy for Dr. ZX Remark

Trouble Occurs.
• Combined operation of arm roll-in and Retrial B • Check Harness
boom raise or combined operation of • Replace Pump 1 Delivery Pressure
arm-roll-in and swing: Arm speed is Sensor
slow.
• Single operation of boom raise: Lifting
force is weak.
• Travel: Slow speed

slow.
• Single operation of boom raise: Lifting
force is weak.

slow.

slow.
• Although speed operating in E mode Retrial B • Check Harness

returns to P speed, returning speed • Replace Pump 1 Control Pressure
becomes low due to this failure. Sensor
T5-6-7
Pilot Failure
Code
11301-3 Abnormal Swing Pilot Pressure Voltage: 4.75 V or higher • Arm Regenerative Control
Sensor High Voltage • Attachment Flow Rate Control
• Swing Alarm Control
11301-4 Abnormal Swing Pilot Pressure Voltage: Less than 0.25 V • Arm Regenerative Control
Sensor Low Voltage • Attachment Flow Rate Control
11302-3 Abnormal Boom Raise Pilot Voltage: 4.75 V or higher • HP Mode Control
Pressure Sensor High Voltage • Arm Regenerative Control
11302-4 Abnormal Boom Raise Pilot Voltage: Less than 0.25 V • HP Mode Control
Pressure Sensor Low Voltage • Arm Regenerative Control
11303-3 Abnormal Arm Roll-In Pilot Voltage: 4.75 V or higher • HP Mode Control
Pressure Sensor High Voltage • Arm Regenerative Control
11303-4 Abnormal Arm Roll-In Pilot Voltage: Less than 0.25 V • HP Mode Control
Pressure Sensor Low Voltage • Arm Regenerative Control
T5-6-8

• Combined operation of Retrial B • Check Harness
arm-roll-in and swing: Arm • Replace Swing Pilot Pressure
speed is slow. Sensor
• In case of the machine
equipped with the swing
alarm (optional) and when
swing alarm is effective,
swing alarm continues to
ring.
• Combined operation of Retrial B • Check Harness
arm-roll-in and swing: Arm • Replace Swing Pilot Pressure
speed is slow. Sensor
• In case of the machine
equipped with the swing
alarm (optional) and when
swing alarm is effective,
swing alarm continues to
ring.
• During HP control, boom Retrial B • Check Harness
raise speed does not in- • Replace Boom Raise Pilot
crease. Pressure Sensor
• Combined operation of arm
roll-in and boom raise: Arm
speed is slow.
• During HP control, boom Retrial B • Check Harness
raise speed does not in- • Replace Boom Raise Pilot
crease. Pressure Sensor
• Combined operation of arm
roll-in and boom raise: Arm
speed is slow.
• During HP control, arm roll-in Retrial B • Check Harness
speed does not increase. • Replace Arm Roll-In Pilot
• Combined operation of arm Pressure Sensor
roll-in and swing: Arm speed
is slow.
• During HP control, arm roll-in Retrial B • Check Harness
speed does not increase. • Replace Arm Roll-In Pilot
• Combined operation of arm Pressure Sensor
roll-in and swing: Arm speed
is slow.
T5-6-9

Code
11304-3 Abnormal Travel Pilot Pressure Voltage: 4.75 V or higher • Auto-Idle Control
Sensor High Voltage • Idle Speed-Up Control
• ECO Control
• Travel HP Mode Control
• Heater Control
• Pump 1 Flow Rate Limit Control
• Travel Motor Swash Angle Con-
trol
• Travel Alarm Control
11304-4 Abnormal Travel Pilot Pressure Voltage: Less than 0.25 V • Auto-Idle Control
Sensor Low Voltage • Idle Speed-Up Control
• ECO Control
• Heater Control
trol
11307-3 Abnormal Front Attachment Pi- Voltage: 4.75 V or higher • Auto-Idle Control
lot Pressure Sensor High • Idle Speed-Up Control
Voltage • ECO Control
• Heater Control
trol
11307-4 Abnormal Front Attachment Pi- Voltage: Less than 0.25 V • Auto-Idle Control
lot Pressure Sensor Low • Idle Speed-Up Control
• Heater Control
trol
T5-6-10
Symptoms in Machine Operation When Remedy for Dr. ZX Remark

Trouble Occurs.
• When traveling at idle speed, engine Retrial B • Check Harness
speed does not increase to the specifi- • Replace Travel Pilot Pressure
cation. Sensor
• When traveling, speed does not return
from auto idle speed.
from ECO speed.
• When operating ATT, the machine mis-
tracks.
• In case of the machine equipped with
the travel alarm (optional), travel alarm
continues to ring.
• When traveling at idle speed, engine Retrial B • Check Harness

speed does not increase to the specifi- • Replace Travel Pilot Pressure
cation. Sensor
from auto idle speed.
from ECO speed.
• When operating ATT, the machine mis-
tracks.
• In case of the machine equipped with
the travel alarm (optional), travel alarm
continues to ring.
• When operating the front attachment at Retrial B • Check Harness
idle speed, engine speed does not in- • Replace Front Pilot Pressure
crease to the specification. Sensor
• When operating the front attachment,
speed does not return from auto idle
speed.
speed does not return from ECO speed.
• Although the front attachment is oper-
ated, travel becomes fast.
• When operating the front attachment at Retrial B • Check Harness
idle speed, engine speed does not in- • Replace Front Pilot Pressure
crease to the specification. Sensor
speed does not return from auto idle
speed.
speed does not return from ECO speed.
• Although the front attachment is oper-
ated, travel becomes fast.
T5-6-11
Proportional Solenoid Valve Failure
Code
11400-2 Abnormal Current Feedback of Current: Both of Higher Pump 2 Flow Rate Limit Control
Maximum Pump 2 Flow Rate Limit than 920mA or Less
Control Solenoid Valve than 60 mA
11400-3 Abnormal Feedback High Current of Current: Higher than Pump 2 Flow Rate Limit Control
Maximum Pump 2 Flow Rate Limit 920mA
11400-4 Abnormal Feedback Low Current of Current: Less than 56 Pump 2 Flow Rate Limit Control
Maximum Pump 2 Flow Rate Limit mA
11401-2 Abnormal Current Feedback of Current: Both of Higher • Speed Sensing Control
Torque Control Solenoid Valve than 920mA or Less • Travel Torque-Up Control
than 60 mA • Attachment Pump Torque De-
crease Control
11401-3 Abnormal Feedback High Current of Current: Higher than • Speed Sensing Control
Torque Control Solenoid Valve 920 mA • Travel Torque-Up Control
• Attachment Pump Torque De-
crease Control
11401-4 Abnormal Feedback Low Current of Current: Less than 56 • Speed Sensing Control
Torque Control Solenoid Valve mA • Travel Torque-Up Control
• Attachment Pump Torque De-
crease Control
11402-2 Abnormal Current Feedback of So- Current: Both of Higher Digging Regenerative Control
lenoid Valve Unit (SF) (Digging than 920mA or Less
Regeneration) than 60 mA
11402-3 Abnormal Feedback High Current of Current: Higher than Digging Regenerative Control
Solenoid Valve Unit (SF) (Digging 920mA
Regeneration)
11402-4 Abnormal Feedback Low Current of Current: Less than 56 Digging Regenerative Control
Solenoid Valve Unit (SF) (Digging mA
Regeneration)
11403-2 Abnormal Current Feedback of So- Current: Both of Higher Arm Regenerative Control
lenoid Valve Unit (SC) (Arm than 920mA or Less
Regeneration) than 60 mA
11403-3 Abnormal Feedback High Current of Current: Higher than Arm Regenerative Control
Solenoid Valve Unit (SC) (Arm Re- 920mA
generation)
11403-4 Abnormal Feedback Low Current of Current: Less than 56 Arm Regenerative Control
Solenoid Valve Unit (SC) (Arm Re- mA
generation)
11404-2 Abnormal Current Feedback of So- Current: Both of Higher • Power Digging Control
lenoid Valve Unit (SG) (Relief than 920mA or Less • Auto-Power Lift Control
Pressure Control) than 60 mA
11404-3 Abnormal Feedback High Current of Current: Higher than • Power Digging Control
Solenoid Valve Unit (SG) (Relief 920mA • Auto-Power Lift Control
Pressure Control)
11404-4 Abnormal Feedback Low Current of Current: Less than 56 • Power Digging Control
Solenoid Valve Unit (SG) (Relief mA • Auto-Power Lift Control
Pressure Control)
T5-6-12
Symptoms in Machine Operation When Trouble Occurs. Remedy for Remark

Dr. ZX
In case ATT flow rate is limited, it cannot be limited. Retrial B • Check Harness
Actual Operation of Proportional Valve during High Current: Retrial B • Check Harness
• Travel mistakes.
• Boom raise operation is slow.
• Arm operation is slow.
• Swing operation is slow.
Actual Operation of Proportional Valve during Low Current: Retrial B • Check Harness
• In case ATT flow rate is limited, it cannot be limited.
Machine overall operation is slow. Retrial B • Check Harness
• The engine is stalled at Li speed.
• Engine Speed: Middle to Fast: Engine Stall or Large Lug Down
• Machine overall operation is slow.
During digging, arm speed is slow. (As deceleration rate is low, Retrial B • Check Harness
this state is not easy to find.)
• Combined operation of boom rasie and arm roll-in during lift-
ing/precision: The boom raise operation is not smooth.
• During digging, arm speed is slow. (As deceleration rate is low,
this state is not easy to find.)
Combined operation of boom raise and arm roll-in with the front Retrial B • Check Harness
attachment over ground, the boom is not raised smoothly and the
arm roll-in full-speed is slow.
• Digging force (arm) becomes weak.
• Combined operation of boom raise and arm roll-in with the front
attachment over ground, the boom is not raised smoothly and
the arm roll-in full-speed is slow.
Pressure increasing is impossible. Retrial B • Check Harness
• Pressure always increases.
• Pressure increasing is impossible.
T5-6-13

Code
11405-2 Abnormal Current Feedback of Current: Both of Higher than Travel Motor Swash Angle
Solenoid Valve Unit (SI) (Travel 920mA or Less than 60 mA Selection Control
Motor Fast Speed Selection)
11405-3 Abnormal Feedback High Cur- Current: Higher than 920mA Travel Motor Swash Angle
rent of Solenoid Valve Unit (SI) Selection Control
(Travel Motor Fast Speed Se-
lection)
11405-4 Abnormal Feedback Low Cur- Current: Less than 56 mA Travel Motor Swash Angle
rent of Solenoid Valve Unit (SI) Selection Control
(Travel Motor Fast Speed Se-
lection)
T5-6-14

Dr. ZX
Travel motor is always slow. Retrial B • Check Harness
Operation of Proportional Valve during High Current: Retrial B • Check Harness

• Travel motor is always slow.
Operation of Proportional Valve during Low Current: Retrial B • Check Harness

• Travel motor is always slow.
T5-6-15
CAN Data Reception Failure
Code
11910-2 Actual Engine Speed Faulty Harness • Speed Sensing Control
Received from ECM • Send to ICF
11918-2 Work Mode Faulty Harness • Attachment Operation Speed

Received from Monitor Unit Increase Control
Limit Control
Decrease Control
trol
trol
• Attachment Flow Rate Con-
trol
• Attachment Valve Selection
(Optional)
11911-2 Security Signal Faulty Harness Theft Prevention Engine Speed,
Received from ECM Engine Torque
11920-2 Fuel Flow Rate Faulty Harness Fuel Flow Rate

Received from ECM
11914-2 Radiator Coolant Temperature Faulty Harness Heater Control
Received from ECM
T5-6-16

Dr. ZX
Machine operation speed is slow. (During speed sensing, Retrial B • Check Harness
torque is decreased.)
During e-service, the engine is stalled.
• Digging Mode: Lock Retrial B • Check Harness
In case flow rate is decreased and speed decreases during
ATT, stop this control, or Digging is not changed into ATT
mode.
• Work Mode Alarm is displayed on the monitor unit.
T1V1-05-01-102
In case theft prevention is turned ON by Dr. ZX, engine Retrial B • Check Harness
speed is kept at Minimum speed and pump torque is kept
Minimum.
When the monitor setting is displayed fuel consumption at Retrial B • Check Harness
moment, engine display at moment is “----“.
Heater Control: Ineffective Retrial B • Check Harness
T5-6-17
Other Failures
Code
11901-3 Hydraulic Oil Temperature Voltage: 4.52 V or higher • Auto-Warming Up Control
Sensor High Voltage • Arm Regenerative Control
11901-4 Hydraulic Oil Temperature Voltage: Less than 0.23 V • Auto-Warming Up Control
Sensor Low Voltage • Arm Regenerative Control
11905-3 Abnormal Boom Bottom Pres- Voltage: 4.5 V or higher • Overload Alarm
sure Sensor High Voltage
(Optional)
11905-4 Abnormal Boom Bottom Pres- Voltage: Less than 0.25 V • Overload Alarm
sure Sensor Low Voltage
(Optional)
T5-6-18

Dr. ZX
When temperature is low (hydraulic oil temperature is less Retrial B • Check Harness
than 0 °C), the auto-warming up control is inoperable.
When temperature is low (hydraulic oil temperature is less Retrial B • Check Harness
than 0 °C), the auto-warming up control is inoperable.
When overload alarm is used. Retrial B • Check Harness

• Overload alarm buzzer rings. • Replace Boom Bottom
• The overload alarm is displayed on the monitor unit. Pressure Sensor
T1V1-05-02-002
When overload alarm is used. Retrial B • Check Harness

• Overload alarm buzzer rings. • Replace Boom Bottom
• The overload alarm is displayed on the monitor unit. Pressure Sensor
T1V1-05-02-002
T5-6-19
ECM
Sensor System
Fault Trouble Cause
Code
636-2 Abnormal Cam Angle Sensor (No Signal) Although the crank signal is present, the cam signal is
not present.
636-2 Abnormal Cam Angle Sensor (Abnormal The pulse of cam signal is not matched.
Signal)
723-2 Abnormal Crank Speed Sensor (No Sig- Although the cam signal is present, the crank signal is
nal) not present.
723-2 Abnormal Crank Speed Sensor (Abnor- The pulse of crank signal is not matched.
mal Signal)
636-7 Phase Mismatch of Cam Angle Sensor The right cam pulse is not present at the gap in the
crank.
172-3 Abnormal Intake-Air Temperature Sensor Voltage at the intake-air temperature sensor is be-
(Abnormal High Voltage) yond 4.95 V in 3 minutes after the engine starts.
172-4 Abnormal Intake-Air Temperature Sensor Voltage at the intake-air temperature sensor is below
(Abnormal Low Voltage) 0.1 V.
110-3 Abnormal Coolant Temperature Sensor Voltage at the coolant temperature sensor is beyond
(Abnormal High Voltage) 4.85 V.
110-4 Abnormal Coolant Temperature Sensor Voltage at the coolant temperature sensor is below
(Abnormal Low Voltage) 0.1 V
102-4 Abnormal Boost Pressure Sensor (Ab- Voltage at the boost pressure sensor is beyond 4.9 V.
normal High Voltage)
102-3 Abnormal Boost Pressure Sensor (Ab- Voltage at the boost pressure sensor is below 0.1 V
normal Low Voltage)
10001-3 Abnormal EGR Position (Brushless The condition which the output signal of EGR position
spec.) cannot be present in.
108-4 Abnormal Atmospheric Pressure Sensor Voltage at the atmospheric pressure sensor is beyond
108-3 Abnormal Atmospheric Pressure Sensor Voltage at the atmospheric pressure sensor is below
174-3 Abnormal Fuel Temperature Sensor (Ab- Voltage at the fuel temperature sensor is beyond 4.85
normal High Voltage) V in 3 minutes after the engine starts.
174-4 Abnormal Fuel Temperature Sensor (Ab- Voltage at the fuel temperature sensor is below 0.1 V.
normal Low Voltage)
T5-6-20
Presumptive Symptoms in Real Machine Opera- Assumptive Conditions at Backup Fault Code
tion (Tech 2)
• While the engine runs, there is nothing abnor- While the engine runs, operate according to P0340
mal with machine operation. standard of the crank sensor. When the en-
• After the engine is stalled, the re-start is im- gine stops, the start is impossible (in order to P0341
possible. prevent the engine from damaging).
• The output power may decrease, white smoke Operate according to standard of the cam sen- P0335
may occur and vibration may occur. sor.
• The engine may be stalled. (If the cam senor is P0336
normal, the engine can re-start.)
• While the engine runs, there is nothing abnor- The timing chain and the belt does not turn P1345
mal with machine operation. smoothly but turn in reverse.
• After the engine is stalled, the re-start is im-
possible.
Nothing special When starting: -10 °C (14 °F) (Start the engine P0113
although what state.)
When operating: 25 °C (77 °F) (Operate nor- P0112
mally.)
Normal temperature: When starting, dark smoke When starting: -20 °C (-4 °F) (Start the engine P0118
may occur and engine combustion sound may be although what state.)
become loud. When operating: 80 °C (176 °F) (Operate P0117
While warming up with fresh air in low tempera- normally.)
ture: Rough idle, engine stall or while smoke may
be occur.
Dark smoke occurs. Boost pressure cannot be corrected. P0238
P0237
There is influence to exhaust gas. As the sensor input is not certain, it cannot be P0487
controlled. Exhaust gas becomes bad.
Operate the engine with EGR valve fully open.
2
Dark smoke occurs at high altitude. Atmospheric pressure 80 kPa (0.8 kgf/cm , 12 P0108
psi) (2000 m above the sea)
O0107
Nothing special When starting: -20 °C (-4 °F) (Start the engine P0183
although what state.)
When operating: 70 °C (158 °F) (Operate nor- P0182
mally.)
T5-6-21
Fault Trouble Cause

Code
157-3 Abnormal Common Rail Pressure Sensor Voltage at the common rail pressure sensor is beyond
157-3 Abnormal Common Rail Pressure Sensor Voltage at the common rail pressure sensor is below
100-4 Abnormal Engine Oil Pressure Sensor Voltage at the engine oil pressure sensor is beyond
100-3 Abnormal Engine Oil Pressure Sensor Voltage at the engine oil pressure sensor is below 0.1
(Abnormal Low Voltage) V.
105-3 Abnormal Boost Temperature Sensor Voltage at the boost temperature sensor is beyond
(Abnormal High Voltage) 4.95 V over 5 minutes after the engine starts or when
coolant temperature is beyond 50 °C (122 °F).
105-4 Abnormal Boost Temperature Sensor Voltage at the boost temperature sensor is below 0.1
(Abnormal Low Voltage) V.
T5-6-22
Presumptive Symptoms in Real Machine Opera- Assumptive Conditions at Backup Fault Code
tion (Tech 2)
The engine may be stalled. The output power The supply pump can not be controlled. P0193
decreases.
P0192
There is no influence when operating the ma- Nothing special P0523

chine.
P0522
There is no influence when operating the ma- Nothing special P1113

chine.
P1112
T5-6-23
TROUBLESHOOTING/ Troubleshooting A
Influence to Engine Operating Rank

Fault Code Trouble Performance (Current State) Remark
(Presumption) A B C D
636-2 Abnormal Cam Angle Sensor (No No influence during
○ ○
Signal) operationg
636-2 Abnormal Cam Angle Sensor After stopping, the
○ ○
(Abnormal Signal) re-start is impossible.
723-2 Abnormal Crank Speed Sensor (No No output power
○
Signal) decrease
723-2 Abnormal Crank Speed Sensor
○
(Abnormal Signal)
636-7 Phase Mismatch of Cam Angle No influence during
Sensor operationg
○ ○
After stopping, the
re-start is impossible.
172-3 Abnormal Intake-Air Temperature No output power
○
Sensor (Abnormal High Voltage) decrease
172-4 Abnormal Intake-Air Temperature
○
Sensor (Abnormal Low Voltage)
110-3 Abnormal Coolant Temperature No output power
○
110-4 Abnormal Coolant Temperature
○
102-4 Abnormal Boost Pressure Sensor No output power
○
(Abnormal High Voltage) decrease
102-3 Abnormal Boost Pressure Sensor
○
(Abnormal Low Voltage)
10001-3 Abnormal EGR Position (Brushless No output power
○
spec.) change
108-4 Abnormal Atmospheric Pressure No output power
○
108-3 Abnormal Atmospheric Pressure
○
174-3 Abnormal Fuel Temperature Sensor No output power
○
(Abnormal High Voltage) decrease
174-4 Abnormal Fuel Temperature Sensor
○
157-3 Abnormal Common Rail Pressure Output power
○
Sensor (Abnormal High Voltage) decrease: 70%
157-4 Abnormal Common Rail Pressure
○
100-4 Abnormal Engine Oil Pressure No output power
○
Sensor (Abnormal High Voltage) change
100-3 Abnormal Engine Oil Pressure
○
T5-6-24
Influence to Engine
Fault Operating Rank
Trouble Performance Remark
Code (Current State)
(Presumption)
105-3 Abnormal Boost Temperature Sensor No output power
○
(Abnormal High Voltage) change
105-4 Abnormal Boost Temperature Sensor
○
Operating Rank
A: Diggings operable.
B: Machine can travel with boom raised. (Steering is
impossible.)
C: The engine only runs. (Travel, digging and
operation with light load are impossible.)
D: The engine cannot stop / start.
IMPORTANT: When fault code 723-2 (abnormal

crank speed sensor) is displayed
and the engine does not start, the
cam angle sensor is faulty although
fault codes 636-2 (abnormal cam
angle sensor) and 636-7 (phase
mismatch of cam angle sensor) are
not displayed.
T5-6-25
External Device System
Fault Code Trouble Cause
10002-2 Abnormal EGR valve control Difference between the target valve lift and actual position
isbeyond 20%.
1347-0 Open circuit in suction control valve The suctioncontrol valve drive current is beyond 2400 mA or
drive system, Shorted circuit in + B or below 50 mA. Or, difference between the tartget current and
GND actual current is 1000 mA or more.
651-3 Open circuit in injection nozzle ＃1 No input signal of injector 1 monitor.

drive system
drive system
drive system
654-3 Open circuit in injection nozzle #4 No input signal of injector 4 monitor.
drive system
T5-6-26
Presumptive Symptoms in Real Machine Fault Code

Assumptive Conditions at Backup
Operation (Tech 2)
There is influence to exhaust gas. EGR cannot be controlled. P0488
As exhaust gas becomes bad, EGR stops.
The engine may be stalled and the rotation The supply pump cannot be controlled. P0090
speed increases automatically and abnormally → Prevent the engine from increasing the rotation
according to open or shorted circuitc ondition. speed automatically and abnormally (Protect the
Dark smoke occurs. Output power is too large. engine).
Vibration of the engine is large, Rough idle, #1 injector cannot be controlled. P0201
output power decrease, faulty increasing of → Stop drive pulse output of #1 injector.
rotation speed, output power decrease
#2 injector cannot be controlled. P0202
→ Stop drive pulse output of #2 injector.
T5-6-27
Fuel System
157-0 Abnormal common rail pressure Common rail pressure is beyond 185 Mpa.
(First stage)
157-0 Abnormal commo rail pressure The first stage “Abnormal common rail presure” is
(Second stage) approveand commonrail pressure is beyond 190 Mpa.
157-2 Abnormal commonrail pressure When DUTY to the suction control valve is 40 % or more, or
3
(Pump over-pressure) target pressure to the suction control valve is 90 mm /sec or
2
less, actual rail pressure is 40 MPa (410 kgf/cm , 5820 psi)
higher than the target rail pressure.
633-7 Pressure limiter open The pressure limiter is open.
1240-1 No pressure to pump (Fuel leakage) When DUTY to the suction control valve is 33 % or less, or
3
pressure to the suction control valve is 28000 mm /sec or
-1
more and 1200 min , actual rail pressure is 50 MPa (510
2
kgf/cm , 7270 psi) lower than the target rail pressure.
-1
1239-1 No pressure to pump (Fuel leakage) When pressure to the suction control valve is 900 min ,
2
actual rail pressure is 15Mpa (150 kgf/cm , 2180 psi) or less.
T5-6-28

Operation (Tech 2)
Vibration of the engine may be large, Rough idle, Prevention the junection system (pump) from P0088
output power decrease may occur, faulty damage
increasing of rotation speed, dark smoke may (Protect the RP sensor by over-pressure)
occur, output power may be too large.
Vibration of the engine may be large, Rough idle, Prevention the junection system from damage P0088
output power decrease may occur, faulty (Pressure is too much as PR is clogged.)
increasing of rotation speed, dark smoke may
Vibration of the engine may be large, Rough idle, Prevention the junection system (pmp) from P0089
output power decrease may occur, faulty damage
increasing of rotation speed, dark smoke may (Protect the RP sensor by over-pressure)
Output power decrease Rial pressure is beyond the allowable pressure. P1095
Vibration of the engine may be large, Rough idle, Fuel leakage is too much. P1093
output power decrease may occur, faulty Difference between target rail pressure and actual
increasing of rotation speed, dark smoke may rail pressure is larger than the specification.
occur, output power may be too large. (Large deflection)
Vibration of the engine may be large, Rough idle, Fuel leakage is too much. P0087
output power decrease may occur, faulty Actual rail pressure does not increase to the
increasing of rotation speed, dark smoke may required pressure.
T5-6-29

Fault (Current)
Code
10002-2 Abnormal EGR valve control No output power
○
change
1347-0 Open circuit in suction control valve Output power
drive system, Shorted circuit in + B or decrease: 50% ○
GND
651-3 Open circuit in injection nozzle ＃ 1 Output power
○
drive system decrease: 15%
652-3 Open circuit in injection nozzle ＃ 2 (Five cylinders drive.)
○
drive system
653-3 Open circuit in injection nozzle ＃ 3
○
drive system
○
drive system
○
drive system
○
drive system
Operating Rank
Influence to Engine (Current)
Fault
Code
157-0 Abnormal common rail pressure (First Output power

○
stage) decrease: 50%
157-0 Abnormal commo rail pressure Output power
○
(Second stage) decrease: 50%
157-2 Abnormal commonrail pressure Output power
○
(Pump over-pressure) decrease: 50%
633-7 Pressure limiter open Output power
○
decrease: 50%
1240-1 No pressure to pump (Fuel leakage) Output power ○
1239-1 No pressure to pump (Fuel leakage) decrease: 50% ○
Operating Rank
impossible.)
T5-6-30
(Blank)
T5-6-31
110-0 Overheating Coolant temperature is beyond 120 °C (248 °F) when

operating the engine.
-1
190-0 Overrunning In case the engine speed is beyond 2500 min
987-3 Abnormal check engine lamp No monitor signal of the check engine lamp
1485-2 Abnormal main relay system Voltage in the main relay system is 1 V or less with the main
relay coil output ON.
Although the main relay coil output is turned OFF, the main
relay is kept ON.
T5-6-32

Operation (Tech 2)
There is no influence when operating the Nothing special (The history of overheating is P1173
machine. recorded.)
Engine speed of the excavator may not increase Mistake of gear change, etc. P0219
-1
2500 min or more.

Operation (Tech 2)
There is no influence when operating the Nothing special
machine. P0650
The engine cannot start. Nothing
P1625
Electrical power is kept supplying to the Nothing
machine.
T5-6-33
Operating Ranke
Influence to Engine (Current)
Fault
Code
110-0 Overheating No output power

○
change
190-0 Overrunning No output power
○
change
Influence to Engine Operating Ranke

Fault (Current)
Code
987-3 Abnormal check engine lamp No output power
○
change
1485-2 Abnormal main relay system The engine stops. ○
Nothing (The engine
cannot re-start
○ ○
according to battery
voltage.)
Operating Rank
impossible.)
T5-6-34
(Blank)
T5-6-35
Internal Circuit System
10005-1 Abnormal Charge Circuit (Bank 1) In case volate at bank 1 of charge circuit in ECM is low
10006-1 Abnormal Charge Circuit (Bank 2) In case volate at bank 2 of charge circuit in ECM is low
10008-2 Abnormal A/D Conversion A/D conversion cannot be done.

10007-2 Abnormal CPU Within 100 msec after the key switch is turned ON, failure of
main CPU is detected by sub CPU.
(Sub CPU resets CPU.)
1077-2 Abnormal IC for CPU watching No change of RUN-SUB pulse in 20 msec
628-2 Abnormal ROM ROM is broken.
10013-2 Abnormal EEPROM EEPROM is broken.
1079-2 Abnormal 5 V Power Source 1 When battery volate is between 16 V and 32 V, voltage of
Voltage IGKEY power source is 5.5 V or more or 4.5 V or less.
10003-2 Abnormal Injection Nozzle Common No monitor siganals of injectors 1, 3, 5

1 Drive System
10004-2 Abnormal Injection Nozzle Common No monitor siganals of injectors 2, 4, 6
2 Drive System
T5-6-36

Operation (Tech 2)
Vibration of the engine may be large, Rough idle, The injector cannot be controlled. P0611
output power decrease may occur, faulty → Stop output of drive signal at broken common
increasing of rotation speed may occur, the side
engine may be stalled. (Protect the engine from damage) P0612
Output power decrease, dark smoke occur. All analogue sensor cannot be used. P1630
Output power decrease CPU is broken. P0606
The engine cannot start. P0606
Output power decrease Sub CPU is broken. P0601

The engine stops. Data of ROM cannot be read. P1603
There is no influence when operating the Data cannot be written to EEPROM. P1631
machine.
Same as Abnormal accelerator Sensor ← P1632
Same as Abnomal atmospheric and in-take ← P1633

temperaturecsensors
Same as Abnomal coolant temperature, fuel ← P1634

temperature and hydraulic oil pressure sensors
Same as Abnomal boost pressure and boost ← P1635

temperature sensors
Same as Abnomal rail pressure and EGR ← P1261

position sensors
Vibration of the engine may be large, Rough idle, The injector cannot be controlled. P1262
output power decrease may occur, faulty → Stop output of drive signal at broken common
increasing of rotation speed may occur, the side
engine may be stalled. (Protect the engine from damage)
T5-6-37

Fault Code Trouble Performance (Current) Remark
10005-1 Abnormal Charge Circuit (Bank 1) Output power ○ ○
10006-1 Abnormal Charge Circuit (Bank 2) decrease: 60%
○ ○
(Three cylinders drive.)
10008-2 Abnormal A/D Conversion Output power
○
decrease: 50%
10007-2 Abnormal CPU Output power
○
decrease: 50%
The engine cannot
○
start.
1077-2 Abnormal IC for CPU watching Output power
○
decrease: 50%
628-2 Abnormal ROM The engine stops. ○
10013-2 Abnormal EEPROM No output power
○
decrease
1079-2 Abnormal 5 V Power Source 1 Voltage Idle Speed Operation ○
1080-2 Abnormal 5 V Power Source 2 Voltage No output power
○
decrease
○
change
○
decrease
10011-2 Abnormal 5 V Power Source 5 Voltage Output power
○ ○
decrease: 50%
10003-2 Abnormal Injection Nozzle Common 1 Output power
○ ○
Drive System decrease: 60%
10004-2 Abnormal Injection Nozzle Common 2 (Three cylinders drive.)
○ ○
Drive System
Operating Rank
impossible.)
T5-6-38
(Blank)
T5-6-39
Communication System
639-2 Abnormal CAN Bus Line Detect the bus line off.
639-3 Abnormal CAN Time Out In case the CAN data reception is not approved in
prescribedtime
T5-6-40

Operation (Tech 2)
Speed is turnd into idle speed. CAN communication is operable. U2104
U2106
T5-6-41

Fault
Trouble Performance (Current) Remark
Code
639-2 Abnormal CAN Bus Line Idle speed ○
639-3 Abnormal CAN Time Out ○
T5-6-42
(Blank)
T5-6-43
ICF
14000-2 Abnormal CAN Communication Data cannot be received due to the noise on the CAN bus
line.
14001-2 ICF: Flash Memory: Read / Write In case the internal memory is abnormal when the key is
Error turned ON
14002-2 ICF: External RAM: Read / Write In case the internal memory is abnormal when the key is
Error turned ON
14003-2 ICF: EEPROM: Sum Check Error In case the internal memory is abnormal when the key is
turned ON
14006-2 ICF: Satellite Communication In casse communication to the satellite terminal cannot be
Terminal: Communication Error done over 30 seconds.
14008-2 ICF: Abnormal Internal RAM In case the internal memory is abnormal when the key is
turned ON
T5-6-44
Fault Code Remedy
14000-2 Check for CAN communication bus line.
14001-2 After initializng the information C/U by using Dr. ZX, re-try in the troubleshooting.
If the error code is displayed after re-try, ICF may be broken.
Replace ICF.
NOTE: When initialising the information C/U, all stored data is deleted.
14002-2 After initializng the information C/U by using Dr. ZX, re-try in the troubleshooting.
Replace ICF.
NOTE: When initialising the information C/U, all stored data is deleted.
14003-2 As ICF may be broken, replace ICF.
14006-2 Check for the items below.

1. Check if the communication line is abnormal.
2. Check if the electrical power source of communication terminal is abnormal.
• Electrical power source
• Fuses
3. Check if the satellilte terminal is broken.
14008-2 Re-try in the troubleshooting by using Dr.ZX.
T5-6-45
Satellite Terminal
14100-2 Satellite Communication Terminal: Data cannot be received due to the noise on the CAN bus
Abnormal EEPROM line.
14101-2 Satellite Communication Terminal: In case the internal memory is abnormal when the key is
Abnormal IB/OB Queue turned ON
Abnormal Local Loup Back turned ON
The satellite is not found. turned ON
14104-2 Satellite Communication Terminal: In casse communication to the satellite terminal cannot be
Fail 1 of Remote Loup Back done over 30 seconds.
Fail 2 of Remote Loup Back turned ON
14106-2 Satellite Communication Terminal: In case sending and receiving data are unmatched.
mistached.
T5-6-46
Fault Code Remedy
14100-2 Replace the controller.
14102-2 • Check communication aerial of satellite terminal.
14103-2 • Check communication aerial of satellite terminal.
T5-6-47
Monitor Unit
13303-2 Abnormal Thermister Temperature Thermister temperature is 85 °C (185 °F) or higher.

13304-2 Abnormal REG Input H Level During REG input H level
13306-2 Abnormal EEPROM When failure reading EEPROM occurs
13308-2 Abnormal CAN Communication Bus off occurs beyond five times.
13310-3 Shorted circuit in Coolant The state, input 105±30 Ω or less, is kept over 60 seconds.
Temperature Sensor
13311-3 Shorted circuit in Fuel Leverl Sensor The state, input 3±1 Ω or less, is kept over 60 seconds.
13311-4 Open circuit in Fuel Leverl Sensor The state, input 135±20 Ω or less, is kept over 60 seconds.
T5-6-48
Fault Code Remedy
13303-2 Cool the monitor unit and so on until temperature inside the monitor unit is less than 85 °C
(185 °F).
13304-2 (Refer to the Troubleshooting flow chart.)
13306-2 If this fault code is displayed after retarial, replace the monitor unit.
13308-2 Refer to “Check CAN Harness” on page T5-6-54.
13310-3 Check coolant temperature sensor and harness.
13311-3 Check fuel level sensor and harness.
13311-4 Check fuel level sensor and harness.
T5-6-49
CONTROLLER HARDWARE FAILURE
MC FAULT CODE 11000 to 11002
Fault Code Trouble Cause Influenced Control

11000-2 Abnormal EEPROM Faulty MC All Control
11001-2 Abnormal RAM Faulty MC All Control
11002-2 Abnormal A/D Conversion Faulty MC All Control
YES *Faulty MC
Check if operation of engine
and machine is normal.
Faulty MC
NO
* When the fault code is displayed in the result of

retrial and If operation of engine and machine is
normal, the machine can be used.
T5-6-50
MC FAULT CODE 11003

11003-3 Abnormal Sensor Voltage Faulty MC All Control
YES Faulty sensor

Disconnect connectors of
all sensors corresponding
to the displayed fault code
and retry. Check if fault Disconnect all
code 11003-3 disappears. connectors at MC YES Short-circuited harness
end. Check for between MC and sensor in
continuity between the harness with continuity
terminals #1 and #3
of harness end
NO
connector of each
sensor. Faulty MC
NO
· Key switch: OFF
Connector (Harness end of connector viewed from the

open side)
• Pressure Sensor (Travel) • Pump 1 Delivery Pressure Sensor:
• Pressure Sensor (Front Attachment) • Pump 2 Delivery Pressure Sensor
• Pressure Sensor (Swing)
• Pressure Sensor (Boom Raise)
• Pressure Sensor (Arm Roll-In) 3 2 1
• Pressure Sensor (Auxiliary) (Optional)
• Pump 1 Control Pressure Sensor
• Pump 2 Control Pressure Sensor
1 2 3
T5-6-51
MC FAULT CODE 11004

11004-2 Abnormal CAN Faulty MC • Heater Control
Communication • Speed Sensing Control
• Attachment Operation Speed Increase
Control
• Attachment Operation Speed Limit Control
• Attachment Pump Torque Decrease Control
• Attachment Flow Rate Control (Optional)
• Attachment Valve Selection (Optional)
• CAN Cycle Data Communication
Dr.ZX
Satellite
Terminal
Monitor Unit ICF
CAN Harness
MC
ECM
T1V1-02-01-050
T5-6-52
(Blank)
T5-6-53
CAN HARNESS CHECK
• Check the wiring connections first.
Open circuit in CAN

harness between
NO MC and ECM.
Check for continuity in
YES CAN harness between
MC and ECM.
Check for continuity
in CAN harness
Check for continuity in · Key switch: OFF YES between MC and
· Refer to “CAN monitor unit.
YES CAN harness between Harness Continuity
MC and ICF. · Key Switch OFF
Check” on T5-6-58.
· Refer to “CAN
Harness Continuity
· Key switch: OFF
Check” on T5-6-58.
· Refer to “CAN
Harness Continuity Open circuit in CAN
Retry by using Dr. ZX.
Check” on T5-6-58. harness between
Check if fault code
11004-2 is displayed. NO MC and ICF.
Normal.
NO
T5-6-54
Short-circuited CAN
Disconnect all YES
harness between ground
connectors in MC, circuit and CAN circuit
ICF, ECM and
monitor unit.
YES Check for continuity YES Short-circuited CAN
between CAN circuit
harness between power
and ground circuit in
circuit and CAN circuit
MC, ICF, ECM and
monitor unit.
Check for continuity Short-circuited CAN
· Key switch: OFF YES harness between key
· Refer to NO between CAN circuit
and power circuit in Check for continuity signal circuit and CAN
“Discontinuity Check
MC, ICF, ECM and between CAN circuit circuit
between CAN Circuit
and Ground Circuit” monitor unit. and key signal circuit
NO in MC, ICF, ECM and Check for continuity
on T5-6-61 to 64. · Key switch: OFF
monitor unit. between High side and To A
· Refer to
“Discontinuity Check NO Low side in CAN
· Key switch: OFF harness.
between CAN Circuit · Refer to “Discontinuity
and Power Circuit” Check between CAN · Key switch: OFF
on T5-6-65 to 67. Circuit and Key · Refer to “Discontinuity
Signal Circuit” on Check in CAN
T5-6-69 to 71. Harness on T5-6-72.
Open circuit in CAN

harness between MC and
NO monitor unit
T5-6-55
YES Short-circuited CAN

harness.
NO Check the
Connect connector connection of MC
YES in MC. and connector.
A Check if fault code
Connect all 11004-2 is
connectors except displayed. Faulty MC.
connector MC-C in YES
MC. · Key switch: ON
Check if resistance
between terminals NO Check the
Connect connector connection of ICF
#C4 and #C15 of in ICF.
NO harness end of YES and connector.
Connect connector in Check if fault code
connector MC-C is MC. Disconnect 11004-2 is
within 60±10 Ω. connector ICF-C in displayed. Faulty ICF.
ICF. YES
· Key switch: OFF · Key switch: ON
Check if resistance
between terminals
#C5 and #C11 of Connect connector
NO harness end of Connect connector in YES in ECM. Check if
connector is within ICF. fault code 11004-2
60±10 Ω. Disconnect is displayed.
· Key switch: OFF connector in ECM.
Check if resistance · Key switch: ON
between terminals
NO #18 and #37 of
Connector harness end of Connect connector in
connector is within ECM.
MC 120±10 Ω. Disconnect
Connector MC-C connector monitor-B
(Harness end) · Key switch: OFF in monitor unit.
NO
#C4 #C15 Check if resistance
C1 C10 between terminals
#B6 and #B7 of
harness end of
connector is within
120±10 Ω.
C23 C31
· Key switch: OFF
ICF
Connector ICF-C
(Harness end)
#C5
T1V1-05-04-002
#C11
Monitor Unit
ECM Connector Monitor-B Connector
Connector (Harness end)
(Harness end) #18 #37 #B7 #B6
T1GR-05-04-002
T183-05-04-013
T5-6-56
NO Adjust the connection of

ECM and connector.
Faulty ECM.
YES
NO Check the connection

Connect connector in of monitor unit and
YES monitor unit. connector.
Check if fault code
11004-2 is displayed. Faulty monitor unit.
YES
· Key switch: ON
Failure in any controller

of MC, ICF, ECM and
NO monitor unit.
T5-6-57
Continuity Check in CAN Harness
IMPORTANT: Before continuity check, turn the key

switch OFF.
• Between MC and ECM

CAN Harness (High Side)
Check for continuity between terminal #C4 of
harness end of connector MC-C in MC and
terminal #18 of harness end of connetor in ECM.
CAN Harness (Low Side)

terminal #37 of harness end of connetor in ECM.
Connector
MC
Connector MC-C
(Harness end)
#C4 #C15
C1 C10
C23 C31
ECM
Connector
(Harness end)
#18 #37
T1GR-05-04-002
T5-6-58
• Between MC and ICF
terminal #C5 of harness end of connetor ICF-C in
ICF.

terminal #C11 of harness end of connetor ICF-C
in ICF.
Connector
MC
Connector MC-C
(Harness end)
#C4 #C15
C1 C10
C23 C31
ICF
Connector ICF-C
(Harness end)
#C5
#C11 T1V1-05-04-002
T5-6-59
• Between MC and Monitor Unit
terminal #B7 of harness end of connetor
monitor-B in the monitor unit.

terminal #B6 of harness end of connetor
monitor-B in the monitor unit.
Connector
MC
Connector MC-C
(Harness end)
#C4 #C15
C1 C10
C23 C31
Monitor Unit
Connector Monitor-B
(Harness end)
#B7 #B6
T183-05-04-013
T5-6-60
Discontinuity Check between CAN Circuit and
Ground Circuit Connector
IMPORTANT: Before continuity check, turn the key Connector MC-C

(Harness end)
switch OFF.
• In case of continuity, the circuit between #C4
CAN circuit and ground circuit is C1 C10
shorted.
• In case of discontinuity, the circuit is
normal.
C23 C31
• MC
Between CAN Circuit (High Side) and Ground Connector MC-A
Circuit (Harness end)
harness end of connector MC-C and terminal #A2 #A2
of harness end of connetor in MC-A.

harness end of connector MC-C and terminal
#A13 of harness end of connetor in MC-A.
#A13
T183-05-04-008
harness end of connector MC-C and terminal #B8 Connector MC-B
of harness end of connetor in MC-B. (Harness end)
#B8
#B18 of harness end of connetor in MC-B.
#B18
T183-05-04-021
T5-6-61
Between CAN Circuit (Low Side) and Ground
Circuit Connector
harness end of connector MC-C and terminal #A2
Connector MC-C
of harness end of connetor in MC-A. (Harness end)
Check for continuity between terminal #C15 of #C15

harness end of connector MC-C and terminal C1 C10
#A13 of harness end of connetor in MC-A.

C23 C31
harness end of connector MC-C and terminal #B8
of harness end of connetor in MC-B.
Connector MC-A
(Harness end)
harness end of connector MC-C and terminal #A2
#B18 of harness end of connetor in MC-B.
#A13
T183-05-04-008
Connector MC-B
(Harness end)
#B8
#B18
T183-05-04-021
T5-6-62
• ECM
Between CAN Circuit (High Side) and Ground
Circuit ECM
Check for continuity between terminals #18 and Connector
#1 of harness end of connector. (Harness end)
#18 #43
Check for continuity between terminals #18 and
#4
#3 of harness end of connector.
#3
T1GR-05-04-002
#62 #1

Between CAN Circuit (Low Side) and Ground ECM

Circuit Connector
Check for continuity between terminals #37 and (Harness end)
#37 #43
#4
#3
Check for continuity between terminals #37 and T1GR-05-04-002

#4 of harness end of connector. #62 #1


T5-6-63
• ICF
Between CAN Circuit (High Side) and Ground ICF
Circuit Connector ICF-C
Check for continuity between terminals #C5 and (Harness end)
#C14 of harness end of connector ICF-C.
#C5
Check for continuity between terminals #C5 and
T1V1-05-04-002
#C14 #C15
Between CAN Circuit (Low Side) and Ground ICF

(Harness end)

T1V1-05-04-002
#C14 #C15 #C11
• Monitor Unit Monitor Unit

Between CAN Circuit (High Side) and Ground Connector Monitor-B
(Harness end)
Circuit
Check for continuity between terminals #B7 and
#B11 of harness end of connector in the monitor #B7
unit.
T183-05-04-013
#B11
Between CAN Circuit (Low Side) and Ground Monitor Unit

Circuit Connector Monitor-B
(Harness end)
Check for continuity between terminals #B6 and
#B11 of harness end of connector in the monitor
#B6
unit.
T183-05-04-013
#B11
T5-6-64
Power Circuit Connector

switch OFF. (Harness end)
CAN circuit and power circuit is shorted. C1 C10
normal.
• MC C23 C31
Between CAN Circuit (High Side) and Power
Circuit
Check for continuity between terminal #C4 of Connector MC-A
harness end of connector MC-C and terminal #A1 (Harness end)
of harness end connector MC-A.
#A1
#A12 of harness end connector MC-A.
#A12
Check for continuity between terminal #C4 of T183-05-04-008
of harness end connector MC-B. Connector MC-B
(Harness end)
Check for continuity between terminal #C4 of #B7
#B17 of harness end connector MC-B.
#B17
T183-05-04-021
T5-6-65
Between CAN Circuit (Low Side) and Power
Circuit Connector
harness end of connector MC-C and terminal #A2 Connector MC-C
of harness end connector MC-A. (Harness end)
#C15
Check for continuity between terminal #C15 of C1 C10
#A12 of harness end connector MC-A.
Check for continuity between terminal #C15 of C23 C31

of harness end connector MC-B. Connector MC-A
(Harness end)
#B17 of harness end connector MC-B. #A1
#A12
T183-05-04-008
Connector MC-B
(Harness end)
#B7
#B17
T183-05-04-021
T5-6-66
• ECM
ECM
Circuit Connector

T1GR-05-04-002
#2
Between CAN Circuit (Low Side) and Power ECM

Connector
Check for continuity between terminals #37 and #37 #5

T1GR-05-04-002
#2
• ICF
ICF
Between CAN Circuit (High Side) and Power Connector ICF-C
#C1 of harness end of connector ICF-C. #C5
#C2
Check for continuity between terminals #C5 and #C1
T1V1-05-04-002
Between CAN Circuit (Low Side) and Power ICF

(Harness end)
#C2
T1V1-05-04-002
#C11
T5-6-67
• Monitor Unit
Circuit Monitor Unit
Connector Monitor-A
Check for continuity between terminal #B7 of (Harness end)
harness endo of connector in the monitor unit and
terminal #A16 of harness endo of connector
monitor-A in the monitor unit.
#A16
T183-05-05-001
Monitor Unit
Connector Monitor-B
(Harness end)
#B7
T183-05-04-013
Between CAN Circuit (Low Side) and Power Monitor Unit

Circuit Connector Monitor-A
harness endo of connector in the monitor unit and
terminal #A16 of harness endo of connector
#A16
T183-05-05-001
Monitor Unit
Connector Monitor-B
(Harness end)
#B6
T183-05-04-013
T5-6-68
Key Signal Circuit Connector

switch OFF. (Harness end)
CAN circuit and key signal circuit is C1 C10
shorted.
normal.
C23 C31
• MC
Between CAN Circuit (High Side) and Key Signal Connector MC-B
Check for continuity between terminal #C4 of #B16
#B16 of harness end of connector MC-B.
T183-05-04-021
Between CAN Circuit (Low Side) and Key Signal Connector

Circuit
Check for continuity between terminal #C15 of Connector MC-C
harness end of connector MC-C and terminal (Harness end)
#B16 of harness end of connector MC-B.
#C15
C1 C10
C23 C31
Connector MC-B
(Harness end)
#B16
T183-05-04-021
T5-6-69
• ECM
Between CAN Circuit (High Side) and Key Signal ECM
Circuit Connector
T1GR-05-04-002
Between CAN Circuit (Low Side) and Key Signal ECM

Circuit Connector
T1GR-05-04-002
• ICF
ICF
Between CAN Circuit (High Side) and Key Signal Connector ICF-C
#C7
T1V1-05-04-002
Between CAN Circuit (Low Side) and Key Signal ICF

Connector ICF-C
Check for continuity between terminals #C11

and #C7 of harness end of connector ICF-C.
#C7
T1V1-05-04-002
#C11
T5-6-70
• Monitor Unit
Monitor Unit
harness end of connector in the monitor unit and
terminal #A7 of harness end of connector #A7
T183-05-05-001
Monitor Unit
Connector Monitor-B
(Harness end)
#B7
T183-05-04-013
Between CAN Circuit (Low Side) and Power

Monitor Unit
harness end of connector in the monitor unit and
terminal #A7 of harness end of connector
monitor-A in the monitor unit. #A7
T183-05-05-001
Monitor Unit
Connector Monitor-B
(Harness end)
#B6
T183-05-04-013
T5-6-71
Discontinuity Check in CAN Harness
IMPORTANT: Before continuity check, turn the key

switch OFF.
• In case of continuity, the circuit between
CAN (high side) circuit and CAN (low
side) circuit is shorted.
normal.
• Connector MC-C • Connector Monitor-B in Monitor Unit

Check for continuity between terminals #C4 and Check for continuity between terminals #B6 and
#C15 of harness end of connector MC-C in MC. #B7 of harness end of connector monitor-B in the
MC
monitor unit.
Connector MC-C
(Harness end)
Monitor Unit
#C4 #C15 Connector Monitor-B
C1 C10 (Harness end)
#B7 #B6
C23 C31
• Connector ECM
T183-05-04-013
#37 of harness end of connector in ECM.
ECM
Connector
(Harness end)
#18 #37
T1GR-05-04-002
• Connector ICF-C
#C11 of harness end of connector ICF-C in ICF.
ICF
Connector ICF-C
(Harness end)
#C5
#C11 T1V1-05-04-002
T5-6-72
ENGINE FAILURE
MC FAULT CODE 11100

-1
11100-2 Abnormal Engine Speed Engine Speed: 4000 min or faster Speed Sensing Control
• ECM sends by using CAN bus line.

The actual engine speed is abnormal.
Perform self-diagnosis of ECM.
T5-6-73
MC FAULT CODE 11101

11101-3 Abnormal Engine Control Dial Voltage: 4.78 V or higher Engine Control Dial Control
Sensor High Voltage
11101-4 Abnormal Engine Control Dial Voltage: Less than 0.22 V Engine Control Dial Control
Sensor Low Voltage
Disconnect connector
of MC. YES Open circuit in
Check for continuity in harness between MC
harnes between and engine control
YES dial.
terminal #C1 of
harness end of
connector MC-C in
MC and terminal #2 in To A
Insert a probe of tester Check if voltage NO
switch panel.
from the back of connector YES between terminals #1
in terminal #2 with switch and #3 of harness end Open circuit in
panel connector of connector is 5±0.5 Check if voltage harness between MC
V. YES and engine control
connected. between terminal #1
When rotating engine · Key switch: ON of harness end of dial (terminal #3).
control dial, chack if connector in switch
voltage becomes NO panel and machine is
specification. specification. Open circuit in
Disconnect connector of harness between MC
switch panel. · Key switch: ON NO and engine control
Check if resistance · Specification: 5±0.5 V dial (terminal #1).
between terminals #1 and
#2 of switch panel end of
connector is 5±0.5 kΩ. Faulty engine control
NO dial.
· Specification: Refer to
the table below.
YES Faulty MC.
Check if voltage
Specification of Engine Control Dial between terminal #C1
Slow Idle 0.3 to 1.0 V A of harness end of
Fast Idle 4.0 to 4.7 V connector MC-C and Shorted circuit in
machine is 0 V. harness between MC
· Key switch: ON NO and engine control
Connector (Harness end of connector viewed from the dial.
open side)
MC
Connector MC-C
#C1
C1 C10
C23 C31
Switch Panel
#3 #2 #1
T5-6-74
PUMP FAILURE
MC FAULT CODE 11200

Pressure Sensor High Voltage • Travel HP Mode Control
• E Mode Control
• Travel Motor Swash Angle
Selection Control
• E Mode Control
Selection Control
Disconnect connector YES Open Circuit harness
MC-D of MC. between MC and pump 1
Check for continuity in delivery pressure sensor.
YES harnes between terminal
#D10 of harness end of
connector MC-D in MC
of pump 1 delivery To A
and terminal #2 in pump
pressure sensor. NO
1 delivery pressure
Check if voltage
NO sensor.
between terminals #1
and #3 of harness end
of connector is 5±0.5
Check if voltage YES Open circuit in harness
between terminal #1 of between MC and pump 1
V. harness end of delivery pressure sensor
Switch pump 1 delivery connector in pump 1 (terminal #3).
pressure sensor with · Key switch: ON
NO delivery pressure
pump 2 delivery sensor and machine is Open circuit in harness
pressure sensor and specification. between MC and pump 1
retry. NO delivery pressure sensor
Check if fault code is · Key switch: ON
· Specification: More (terminal #1).
switched.
than 0.25 V, Les
than 4.5 V Faulty pump 1 delivery
YES pressure sensor.
YES Faulty MC.

Check if voltage
Connector (Harness end of connector viewed from between terminal
the open side) A #D10 of harness end
of connector MC-D Shorted circuit in
MC Pump 1 Delivery and machine is 0 V. harness between MC
Connector MC-D Pressure Sensor
· Key switch: ON NO and engine pump 1
#D10 delivery pressure
sensor.
3 2 1
T183-05-04-009
T5-6-75
MC FAULT CODE 11202

Pressure Sensor High Voltage • Travel HP Mode Control
• E Mode Control
Selection Control
• E Mode Control
Selection Control
MC-D of MC. YES Open circuit in harness
Check for continuity in between MC and pump 2
harnes between delivery pressure sensor.
YES terminal #D4 of
harness end of
of pump 2 delivery To A
and terminal #2 in
pressure sensor. NO
pump 2 delivery
Check if voltage
NO pressure sensor.
of connector is 5±0.5
Check if voltage YES Open circuit in harness
V. harness end of delivery pressure sensor
Switch pump 1 delivery
pressure sensor with connector in pump 2 (terminal #3).
· Key switch: ON
pump 2 delivery NO delivery pressure
pressure sensor and sensor and machine is Open circuit in harness
retry. specification. between MC and pump 2
NO delivery pressure sensor
Check if fault code is · Key switch: ON
switched. (terminal #1).
· Specification: More
than 0.25 V, Les
than 4.5 V Faulty pump 2 delivery
YES Faulty MC.

Check if voltage
Connector (Harness end of connector viewed from the between terminal #D4
open side) A of harness end of
connector MC-D and Shorted circuit in
MC Pump 2 Delivery machine is 0 V. harness between MC
Connector MC-D Pressure Sensor
· Key switch: ON NO and pump 2 delivery
#D4 pressure sensor.
3 2 1
T183-05-04-009
T5-6-76
MC FAULT CODE 11206

11206-3 Abnoraml Pump 1 Control Voltage: 4.75 V or higher • E Mode Control
Pressure Sensor High Voltage • Heater Control
Selection Control
11206-4 Abnormal Pump 1 Control Voltage: Less than 0.25 V • E Mode Control
Pressure Sensor Low Voltage • Heater Control
Selection Control
MC-D of MC.
Check for continuity in Faulty harness
YES between MC and
harnes between
terminal #D11 of pump 1 control
pressure sensor.
YES harness end of
and terminal #2 in
Disconnect connector pump 1 control To A
of pump 1 control pressure sensor. NO
pressure sensor. Check
NO if voltage between Open circuit in
terminals #1 and #3 of harness between MC
Check if voltage
harness end of between terminal #1 of YES and pump 1 control
connector is 5±0.5 V. pressure sensor
harness end of
Switch pump 1 control (terminal #3).
connector in pump 1
pressure sensor with · Key switch: ON control pressure
NO Open circuit in
pump 2 control pressure sensor and machine is
sensor and retry. Check specification. harness between MC
if fault code is switched. NO and pump 1 control
· Key switch: ON pressure sensor
· Specification: More (terminal #1).
than 0.25 V, Les than
4.75 V Faulty pump 1 control
YES Faulty MC.

Check if voltage
between terminal
A #D11 of harness end
and machine is 0 V. harness between MC
· Key switch: ON NO and pump 1 control
pressure sensor.

open side)
MC Pump 1 Control Pressure Sensor
Connector MC-D
#D11
1 2 3
T183-05-04-009
T5-6-77
MC FAULT CODE 11208

11208-3 Abnormal Pump 2 Control Voltage: 4.75 V or higher • E Mode Control
Pressure Sensor High Voltage • Heater Control
Selection Control
11208-4 Abnormal Pump 2 Control Voltage: Less than 0.25 V • E Mode Control
Pressure Sensor Low Voltage • Heater Control
Selection Control
MC-D of MC. Open circuit in harness
Check for continuity in YES between MC and pump 2
harnes between control pressure sensor.
terminal #D14 of
YES harness end of
and terminal #2 in
of pump 2 control
pump 2 control To A
pressure sensor. pressure sensor. NO
Check if voltage
NO between terminals #1
of connector is 5±0.5 Check if voltage YES Open circuit in harness
V. control pressure sensor
harness end of
Switch pump 1 control · Key switch: ON (terminal #3).
connector in pump 2
pressure sensor with
NO control pressure
pump 2 control pressure
sensor and machine is Open circuit in harness
sensor and retry.
specification. between MC and pump 2
Check if fault code is NO control pressure sensor
switched. · Key switch: ON
(terminal #1).
· Specification:
More than 0.25 V,
Less than 4.75 V
Faulty pump 2 control

YES Faulty MC.

Check if voltage
between terminal #C1
A of harness end of
connector MC-C and Shorted circuit in
· Key switch: ON NO and pump 2 control
pressure sensor.
open side)
MC Pump Control Pressure
Connector MC-D Sensor
#D14
1 2 3
T183-05-04-009
T5-6-78
PILOT FAILURE
MC FAULT CODE 11301

11301-3 Abnormal Swing Pilot Voltage: 4.75 V or higher • Arm Regenerative Control
Pressure Sensor High Voltage • Attachment Flow Rate Control
11301-4 Abnormal Swing Pilot Voltage: Less than 0.25 V • Arm Regenerative Control
Pressure Sensor Low Voltage • Attachment Flow Rate Control
MC-C of MC.
Open circuit in harness
Check for continuity in YES
between MC and swing
harnes between
pilot pressure sensor.
terminal #C13 of
YES
harness end of
connector MC-C in MC
and terminal #2 in
swing pilot pressure To A
Disconnect connector NO
of swing pilot pressure sensor.
sensor.
NO Check if voltage
of connector is 5±0.5 Open circuit in harness
V. Check if voltage YES between MC and swing
between terminal #1 of pilot pressure sensor
· Key switch: ON harness end of (terminal #3).
Switch swing pilot connector in pressure
pressure sensor with NO sensor and machine is
other pressure sensor specification. Open circuit in harness
and retry. between MC and swing
Check if fault code · Key switch: ON NO pilot pressure sensor
di · Specification:
(terminal #1).
More than 0.25 V,
Less than 4.75 V
Faulty swing pilot
YES Faulty MC.

Check if voltage
between terminal
A #C13 of harness end
Connector (Harness end of connector viewed from the of connector MC-C Shorted circuit in
open side)
· Key switch: ON NO and swing pilot
MC Pilot Pressure Sensor pressure sensor.
Connector MC-C (Swing)
#C13
C1 C10
1 2 3
C23 C31
T5-6-79
MC FAULT CODE 11302

11302-3 Abnormal Boom Raise Voltage: 4.75 V or higher • HP Mode Control
Pilot Pressure Sensor • Arm Regenerative Control
High Voltage • Digging Regenerative Control
11302-4 Abnormal Boom Raise Voltage: Less than 0.25 V • HP Mode Control
Low Voltage • Digging Regenerative Control
Disconnect connector Open circuit in harness

MC-D of MC. YES between MC and boom
Check for continuity in raise pilot pressure
YES harnes between sensor.
terminal #D15 of
harness end of
connector MC-D in MC To A
Disconnect connector and terminal #2 in NO
of boom raise pilot boom raise pilot
pressure sensor. pressure sensor.
NO Check if voltage
and #3 of harness end Open circuit in harness
of connector is 5±0.5 between MC and boom
V. Check if voltage YES raise pilot pressure
between terminal #1 of sensor (terminal #3).
Switch boom raise pilot · Key switch: ON harness end of
pressure sensor with
connector in boom
other pressure sensor
NO raise pilot pressure
and retry.
sensor and machine is Open circuit in harness
Check if fault code
specification. between MC and boom
disappears. NO raise pilot pressure
· Key switch: ON sensor (terminal #1).
· Specification:
More than 0.25 V,
Less than 4.75 V
Faulty boom raise pilot
YES Faulty MC.

Check if voltage
between terminal
A #D15 of harness end
Connector (Harness end of connector viewed from the and machine is 0 V. harness between MC
open side) · Key switch: ON NO and boom raise pilot
pressure sensor.
Pilot Pressure Sensor (Boom Raise)
MC
Connector MC-D
1 2 3
#D15
T183-05-04-009
T5-6-80
MC FAULT CODE 11303

11303-3 Abnormal Arm Roll-In Voltage: 4.75 V or higher • HP Mode Control
High Voltage • Digging Regenerative Control
11303-4 Abnormal Arm Roll-In Voltage: Less than 0.25 V • HP Mode Control
Low Voltage • Digging Regenerative Control
Disconnect connector YES Open circuit in harness

between MC and
MC-C of MC.
pressure sensor.
YES Check for continuity in
harnes between
terminal #C3 of
harness end of To A
Disconnect connector connector MC-C in MC NO
of arm roll-in pilot and terminal #2 in arm
roll-in pilot pressure
NO pressure sensor. sensor.
Check if voltage
of connector is 5±0.5 Check if voltage Open circuit in harness
YES between MC and arm
between terminal #1
· Key switch: ON of harness end of roll-in pilot pressure
connector in arm sensor (terminal #3).
Switch arm roll-in pilot
pressure sensor with NO roll-in pilot pressure
other pressure sensor sensor and machine Open circuit in harness
and retry. is specification. between MC and arm
Check if fault code NO roll-in pilot pressure
· Key switch: ON
disappears. · Specification: sensor (terminal #1).
More than 0.25 V,
Less than 4.75 V Faulty arm roll-in pilot
YES Faulty MC.

Check if voltage
between terminal #C3
A of harness end of
· Key switch: ON NO and arm roll-in pilot
pressure sensor.

open side)
MC Pilot Pressure Sensor
Connector MC-C (Arm Roll-In)
#C3
C1 C10
1 2 3
C23 C31
T5-6-81
MC FAULT CODE 11304

11304-3 Abnormal Travel Pilot Voltage: 4.75 V or higher • Auto-Idle Control
Pressure Sensor High Voltage • Idle Speed-Up Control
• ECO Control
• Heater Control
Control
11304-4 Abnormal Travel Pilot Voltage: Less than 0.25 V • Auto-Idle Control
Pressure Sensor Low Voltage • Idle Speed-Up Control
• ECO Control
• Heater Control
Control
MC-C of MC. between MC and travel
Check for continuity in pilot pressure sensor.
YES harnes between terminal
#C2 of harness end of
Disconnect connector of and terminal #2 in travel To A
pilot in pressure sensor. NO
travel pilot pressure
sensor.
NO Check if voltage Open circuit in harness
between terminals #1 YES between MC and travel
Check if voltage between pilot pressure sensor
and #3 of harness end terminal #1 of harness
of connector is 5±0.5 V. (terminal #3).
Switch travel pilot end of connector in travel
pressure sensor with NO pilot pressure sensor and
other pressure sensor · Key switch: ON Open circuit in harness
machine is specification.
and retry. between MC and travel
· Key switch: ON
Check if fault code NO pilot pressure sensor
disappears. · Specification: (terminal #1).
More than 0.25 V,
Less than 4.75 V
Faulty travel pilot
open side)
MC Pilot Pressure Sensor (Travel) YES Faulty MC.
Connector MC-C Check if voltage
#C2 between terminal #C2
C1 C10 A of harness end of
1 2 3 machine is 0 V. harness between MC
· Key switch: ON NO and travel pilot
pressure sensor.
C23 C31
T5-6-82
MC FAULT CODE 11307

11307-3 Abnormal Front Attachment Voltage: 4.75 V or higher • Auto-Idle Control
Pilot Pressure Sensor High • Idle Speed-Up Control
• Heater Control
Control
11307-4 Replace Front Attachment Voltage: Less than 0.25 V • Auto-Idle Control
Pilot Pressure Sensor • Idle Speed-Up Control
• ECO Control
• Heater Control
Control

MC-C of MC. between MC and front
Check for continuity in attachment pilot pressure
YES harnes between terminal sensor.
#C12 of harness end of
and terminal #2 in front To A
Disconnect connector NO
attachment pilot
of front attachment pilot
pressure sensor is open
pressure sensor.
NO Check if voltage or shorted.
and #3 of harness end Open circuit in harness
of connector is 5±0.5 V. Check if voltage
between terminal #1 of YES between MC and front
Switch front attachment attachment pilot pressure
· Key switch: ON harness end of
pilot pressure sensor sensor (terminal #3).
connector in front
with other pressure
sensor and retry. attachment pilot
NO
pressure sensor and
Check if fault code Open circuit in harness
machine is specification.
disappears. between MC and front
· Key switch: ON NO attachment pilot pressure
· Specification: sensor (terminal #1).
More than 0.25 V,
Less than 4.75 V Faulty front attachment
YES pilot pressure sensor.
YES Faulty MC.

Check if voltage
between terminal
A #C12 of harness end
Connector (Harness end of connector viewed from the · Key switch: ON NO and front attachment
open side) pilot pressure sensor.
MC Pilot Pressure Sensor

Connector MC-C (Front Attachment)
#C12
C1 C10
1 2 3
C23 C31
T5-6-83
PROPORTIONAL SOLENOID VALVE FAILURE
MC FAULT CODE 11400

11400-2 Abnormal Current Feedback of Current: Both of Higher than Pump 2 Flow Rate Limit Control
Maximum Pump 2 Flow Rate 920 mA or Less than 60 mA
Limit Control Solenoid Valve
11400-3 Abnormal Feedback High Current: Higher than 920 mA Pump 2 Flow Rate Limit Control
Current of Maximum Pump 2
Flow Rate Limit Control Solenoid
Valve
11400-4 Abnormal Feedback Low Current: Less than 56 mA Pump 2 Flow Rate Limit Control
Current of Maximum Pump 2
Flow Rate Limit Control Solenoid
Valve
Switch connectors of
NO Faulty maximum pump2
maximum pump2 flow
flow rate limit control
rate limit control
solenoid valve.
YES solenoid valve and
torque control solenoid
valve.
Check if fault code in Faulty MC.
torque control solenoid YES
valve is displayed.
harness between MC
and maximum pump2
flow rate limit control
solenoid valve.
· Between terminal #A22
of connector MC-A in
MC and terminal #1 of Open circuit in harness.
connector in maximum NO
pump2 flow rate limit
control solenoid valve.
MC and terminal #2 of
connector in maximum
control solenoid valve

open side)
MC
Connector MC-A
#A16 #A22
T183-05-04-008
Limit Control Solenoid Valve
T1V1-05-04-003
T5-6-84
MC FAULT CODE 11401

11401-2 Abnormal Current Feedback of Current: Both of Higher than • Speed Sensing Control
Torque Control Solenoid Valve 920mA or Less than 60 mA • Travel Torque-Up Control
Decrease Control
11401-3 Abnormal Feedback High Current: Higher than 920mA • Speed Sensing Control
Current of Torque Control • Travel Torque-Up Control
Solenoid Valve • Attachment Pump Torque
Decrease Control
11401-4 Abnormal Feedback Low Current: Less than 56 mA • Speed Sensing Control
Current of Torque Control • Travel Torque-Up Control
Solenoid Valve • Attachment Pump Torque
Decrease Control
torque control solenoid NO Faulty torque control
valve and maximum
solenoid valve.
YES control solenoid valve.
Check if fault code in
maximum pump2 flow Faulty MC.
rate limit control solenoid YES
Check for continuity in valve is displayed.
harness between MC
and torque control
solenoid valve.
connector in torque Open circuit in harness.
control solenoid valve. NO
connector in torque

open side)
MC
Connector MC-A
#A19
#A30
T183-05-04-008
Torque Control Solenoid Valve
T1V1-05-04-003
T5-6-85
MC FAULT CODE 11402

11402-2 Abnormal Current Feedback of Current: Both of Higher than Digging Regenerative Control
Solenoid Valve Unit (SF) 920mA or Less than 60 mA
(Digging Regeneration)
11402-3 Abnormal Feedback High Current: Higher than 920mA Digging Regenerative Control
Current of Solenoid Valve Unit
(SF) (Digging Regeneration)
11402-4 Abnormal Feedback Low Current: Less than 56 mA Digging Regenerative Control
(SF) (Digging Regeneration)
Switch connectors of Faulty solenoid valve unit

solenoid valve unit (SF) NO
(SF) (digging
(digging regeneration) regeneration).
YES and other solenoid
valve unit (SC, SG or
SI). Faulty MC.
Check for continuity in Check if fault code in
switched solenoid valve YES
solenoid valve unit (SF) unit is displayed.
(digging regeneration).

connector in solenoid Open circuit in harness.
valve unit (SF) (digging
regeneration). NO
connector in solenoid
valve unit (SF) (digging
regeneration).

open side)
MC
Connector MC-A
T183-05-04-008
#A29 #A32
Solenoid Valve Unit (SF)

(Digging Regeneration)
T1V1-05-04-003
T5-6-86
MC FAULT CODE 11403

11403-2 Abnormal Current Feedback of Current: Both of Higher than Arm Regenerative Control
Solenoid Valve Unit (SC) (Arm 920mA or Less than 60 mA
Regeneration)
11403-3 Abnormal Feedback High Current: Higher than 920mA Arm Regenerative Control
(SC) (Arm Regeneration)
11403-4 Abnormal Feedback Low Current: Less than 56 mA Arm Regenerative Control
(SC) (Arm Regeneration)
solenoid valve unit (SC) NO Faulty solenoid valve unit
(arm regeneration) and (SC) (arm regeneration).
YES other solenoid valve unit
(SF, SG or SI).
switched solenoid valve
unit is displayed. YES
harness between MC
and solenoid valve unit
(SC) (arm regeneration).
Open circuit in harness.
valve unit (SC) (arm NO
regeneration).
valve unit (SC) (arm
regeneration).

open side)
MC
Connector MC-A
#A6 #A10
T183-05-04-008
Solenoid Valve Unit (SC)

(Arm Regeneration)
T1V1-05-04-003
T5-6-87
MC FAULT CODE 11404

11404-2 Abnormal Current Feedback of Current: Both of Higher than • Power Digging Control
Solenoid Valve Unit (SG) 920mA or Less than 60 mA • Auto-Power Lift Control
(Relief Pressure Control)
11404-3 Abnormal Feedback High Current: Higher than 920mA • Power Digging Control
Current of Solenoid Valve Unit • Auto-Power Lift Control
(SG) (Relief Pressure Control)
11404-4 Abnormal Feedback Low Current: Less than 56 mA • Power Digging Control
Current of Solenoid Valve Unit • Auto-Power Lift Control
(SG) (Relief Pressure Control)
Switch connectors of Faulty solenoid valve unit

solenoid valve unit (SG) NO
(SG) (relief pressure
(relief pressure control) control).
YES and other solenoid
valve unit (SF, SC or
SI). Faulty MC.
Check if fault code in
switched solenoid valve YES
harness between MC unit is displayed.
(SG) (relief pressure
control).
of connector MC-A in Open circuit in harness.
connector in solenoid NO
valve unit (SG) (relief
pressure control).
valve unit (SG) (relief
pressure control).

open side)
MC
Connector MC-A
#A17 #A11
T183-05-04-008
Solenoid Valve Unit (SG)

(Relief Pressure Control)
T1V1-05-04-003
T5-6-88
MC FAULT CODE 11405

11405-2 Abnormal Current Feedback of Current: Both of Higher than Travel Motor Swash Angle
Solenoid Valve Unit (SI) 920mA or Less than 60 mA Selection Control
(Travel Motor Fast Speed
Selection)
11405-3 Abnormal Feedback High Current: Higher than 920mA Travel Motor Swash Angle
Current of Solenoid Valve Unit Selection Control
(SI) (Travel Motor Fast Speed
Selection)
11405-4 Abnormal Feedback Low Current: Less than 56 mA Travel Motor Swash Angle
Current of Solenoid Valve Unit Selection Control
(SI) (Travel Motor Fast Speed
Selection)
Faulty solenoid valve unit
solenoid valve unit (SI) NO
(SI) (travel motor fast
(travel motor fast speed
speed selection).
YES selection) and other
solenoid valve unit (SF,
SC or SG).
Check for continuity in switched solenoid valve YES
harness between MC unit is displayed.
(SI) (travel motor fast
speed selection).

MC and terminal #1 of Open circuit in harness.
connector in solenoid NO
valve unit (SI) (travel
motor fast speed
selection).
valve unit (SI) (travel
motor fast speed
selection).
open side)
MC
Connector MC-A
#A5
Solenoid Valve Unit (SI)

#A31 T183-05-04-008
(Travel Motor Fast Speed Selection)
T1V1-05-04-003
T5-6-89
CAN DATA RECEPTION FAILURE
MC FAULT CODE 11910, 11914, 11920

11910-2 Actual Engine Speed Faulty CAN Harness • Speed Sensing Control
Received from ECM • Send to ICF
11914-2 Radiator Coolant Temperature Faulty Harness Heater Control
Received from ECM
11920-2 Fuel Flow Rate Received form Faulty CAN Harness Fuel Flow Rate
ECM
Dr. ZX
Satellite
Terminal
Monitor Unit ICF
CAN Harness
MC
ECM
T1V1-02-01-051
T5-6-90
(Blank)
T5-6-91
CAN HARNESS CHECK
(MC FAULT CODE 11910, 11914, 11920)
Shorted circuit in CAN

YES
harness between ground
Disconnect all circuit and CAN circuit.
connectors of MC, ICF,
ECM and monitor unit.
YES Check for continuity
between ground circuit Check for continuity
(MC, ICF, ECM, between power circuit
monitor unit) and CAN (MC, ICF, ECM,
Check for continuity in circuit. NO monitor unit) and CAN
YES CAN harness between · Key switch: OFF circuit.
MC and ECM.
· Refer to · Key switch: OFF
· Key switch: OFF “Discontinuity Check · Refer to “Discontinuity
· Refer to “Continuity between CAN Circuit Check between CAN
Check in CAN and Ground Circuit”. Circuit and Power
Harness”. Circuit”.
Check if fault code Open circuit in CAN
11004-2 is displayed. harness between MC and
NO
ECM.
Normal.
NO
T5-6-92
YES Shorted circuit in CAN

circuit and CAN circuit.

YES harness between key
signal circuit and CAN
circuit.
between key signal
circuit (MC, ICF, YES Shorted circuit in CAN
NO ECM, monitor unit) harness.
and CAN circuit.
· Key switch: OFF between High side
· Refer to and Low side in CAN Connect all connectors
NO except connector YES
“Discontinuity harness. To A
Check between MC-C in MC.
CAN Circuit and · Key switch: OFF Check if resistance Disconnect
Key Signal Circuit”. · Refer to between terminals #C4 connector in MC.
“Discontinuity Check NO and #C15 of harness
Connect connector of
in CAN Harness”. end of connector harness end. To B
MC-C is within 60±10 NO Check if resistance
Ω. between terminals
· Key switch: OFF #18 and #37 of
connector in ECM is
within 120±10 Ω.
Connector · Key switch: OFF
MC
Connector MC-C
(Harness end)
#C15
#C4
C1 C10
C23 C31
ECM
Connector
(Harness end)
#18 #37
T1GR-05-04-002
T5-6-93
NO Check the connections of

Connect connector
MC and connector.
in MC.
A Check if fault code
11004-2 is
Faulty MC.
displayed.
YES
· Key switch: ON

Connect connector ECM and connector.
in ECM.
YES Check if fault code
11004-2 is
displayed. Faulty ECM.
YES
· Key switch: ON
Connect connector NO Check the connection of

B in ICF. ICF and connector.
11004-2 is
Connect connector in displayed.
ECM. Faulty ICF.
Disconnect · Key switch: ON YES
connector ICF-C in
ICF. NO Check the connections of
Check if resistance Connect connector monitor unit and
NO between terminals in the monitor unit. connector.
YES
#C5 and #C11 of Check if fault code
harness end of Connect connector in 11004-2 is
ICF. Faulty monitor unit.
connector is within displayed.
60±10 Ω. Disconnect YES
connector monitor-B · Key switch: ON
· Key switch: OFF NO in the monitor unit.
Check if resistance
between terminals Failure in any controller in
#B6 and #B7 of MC, ICF, ECM or monitor
harness end of NO unit.
connector is within
120±10 Ω.
· Key switch: OFF
Connector
ICF Monitor Unit
Connector ICF-C Connector Monitor-B
(Harness end) (Harness end)
#C5
#B7 #B6
#C11 T1V1-05-04-002
T183-05-04-013
T5-6-94
MC FAULT CODE 11911, 11918

11911-2 Security Signal Faulty CAN Harness Theft Prevention Engine Speed, Engine
Received from Monitor Unit Torque
11918-2 Work Mode Faulty CAN Harness • Attachment Operation Speed Increase
Received from Monitor Unit Control
• Attachment Operation Speed Limit Control
• Attachment Pump Torque Decrease
Control
• Attachment Valve Selection Control
Dr. ZX
Satellite Terminal
Monitor Unit ICF
CAN Harness
MC
ECM
T1V1-02-01-052
T5-6-95
CAN HARNESS CHECK
(MC FAULT CODE 11911, 11918)
Disconnect all
connectors of MC, ICF, YES Open circuit in CAN
ECM and monitor unit. harness between ground
YES Check for continuity circuit and CAN circuit.
between ground circuit
(MC, ICF, ECM, Check for continuity
monitor unit) and CAN between power
circuit. circuit (MC, ICF,
Check for continuity in NO ECM, monitor unit)
· Key switch: OFF and CAN circuit.
YES CAN harness between · Refer to
MC and monitor unit. “Discontinuity Check · Key switch: OFF
· Key switch: OFF between CAN Circuit · Refer to
· Refer to “Continuity and Ground Circuit”. “Discontinuity Check
Check in CAN between CAN Circuit
Harness”. and Power Circuit”.
Check if fault code Open circuit in CAN
11004-2 is displayed. harness between MC and
NO monitor unit.
Normal.
NO
T5-6-96

YES
circuit and CAN circuit.

YES harness between key
signal circuit and CAN
circuit.
between key signal
circuit (MC, ICF, YES Shorted circuit in CAN
NO ECM, monitor unit) harness.
and CAN circuit.
· Key switch: OFF Check for continuity
· Refer to between High side Connect all
“Discontinuity and Low side in CAN connectors except YES
NO harness. To A
Check between connector MC-C in
CAN Circuit and · Key switch: OFF MC. Connect connector in
Key Signal Circuit”. · Refer to Check if resistance MC.
“Discontinuity Check NO between terminals Disconnect
in CAN Harness”. #C4 and #C15 of connector monitor-B
harness end of in the monitor unit.
connector MC-C is Check if resistance To B
within 60±10 Ω. NO
between terminals
· Key switch: OFF #B6 and #B7 of
harness end of
connector is within
Connector 120±10 Ω.
MC
Connector MC-C · Key switch: OFF
(Harness end)
#C4 #C15
C1 C10
C23 C31
Monitor Unit
Connector Monitor-B
(Harness end)
#B7 #B6
T183-05-04-013
T5-6-97

Connect connector MC and connector.
in MC. Check if fault
A code 11004-2 is
displayed. Faulty MC.
· Key witch: ON YES
Check the connections of

Connect connector NO
monitor unit and
in the monitor unit. connector.
11004-2 is
displayed. Faulty monitor unit.
YES
· Key witch: ON
Connect connector NO Check the connections of

B in ECM. ICF and connector.
Connect connector in
11004-2 is
the monitor unit.
displayed. Faulty ICF.
Disconnect
connector ECM. · Key witch: ON YES
Check if resistance
between terminals
#18 and #37 of Connect connector in Connect connector
NO harness end of ICF and connector.
ECM. YES in ICF.
connector is within Disconnect Check if fault code
120±10 Ω. connector ICF-C in 11004-2 is Faulty ICF.
ICF. displayed.
· Key witch: OFF YES
Check if resistance
· Key witch: ON
between terminals
NO #C5 and #C11 of
harness end of
connector is within Failure in any controller in
60±10 Ω. MC, ICF, ECM or monitor
NO unit.
· Key witch: OFF
Connector
ECM ICF
Connector Connector ICF-C
(Harness end) #18 #37 (Harness end) #C5
#C11 T1V1-05-04-002
T1GR-05-04-002
T5-6-98
OTHER FAILURES
MC FAULT CODE 11901

11901-3 Hydraulic Oil Temperature Voltage: 4.52 V or higher • Auto-Warming Up Control
Sensor High Voltage • Arm Regenerative Control
11901-4 Hydraulic Oil Temperature Voltage: Less than 0.23 V • Auto-Warming Up Control
Sensor Low Voltage • Arm Regenerative Control
Connect terminals #1
YES Faulty MC.
of connector in
hydraulic oil
temperature sensor by Connect terminal #D6
YES using a clip. Open circuit in harness
of harness end of YES between MC and
Disconnect connector connector MC-D in
MC-D from MC. hydraulic oil temperature
MC to machine. sensor (terminal #1).
Check for continuity Check for continuity
Disconnect connector of between terminals #D2
hydraulic oil temperature NO between terminals #2
and #D6 of harness of harness end of
sensor. Open circuit in harness
end of connector connector in hydraulic
Check if resistance at between MC and
MC-D. oil temperature NO
sensor end connector is hydraulic oil temperature
specification. sensor and machine. sensor (terminal #2).
· Specification: Refer to
the table below. Faulty hydraulic oil
NO temperature sensor.
Specification of Hydraulic Oil Temperature Sensor

Hydraulic Oil Temperature Resistance
(°C) (kΩ)
-20 16.2±1.6
0 (5.88)
20 2.45±0.24
40 (1.14)
60 (0.534)
80 0.322

open side)
MC
Connector MC-D
#D2
#D6 T183-05-04-009

Sensor
1 2
T5-6-99
ECM, SENSOR SYSTEM
ECM FAULT CODES 100, 102, 105, 108, 110, 157, 172
Fault Trouble Fault Code (Tech 2) Reference Page on

Code Engine Troubleshooting
Manual
100-3 Abnormal Engine Oil Pressure Sensor (Abnormal P0522 1E-403
Low Voltage)
100-4 Abnormal Engine Oil Pressure Sensor (Abnormal P0523 1E-409
High Voltage)
102-3 Abnormal Boost Pressure Sensor (Abnormal Low P0237 1E-341
Voltage)
102-4 Abnormal Boost Pressure Sensor (Abnormal P0238 1E-348
High Voltage)
105-3 Abnormal Boost Temperature Sensor (Abnormal P1113 1E-460
High Voltage)
105-4 Abnormal Boost Temperature Sensor (Abnormal P1112 1E-452
Low Voltage)
108-3 Abnormal Atmospheric Pressure Sensor P0107 1E-231
108-4 Abnormal Atmospheric Pressure Sensor P0108 1E-238
(Abnormal High Voltage)
110-3 Abnormal Coolant Temperature Sensor P0118 1E-266
110-4 Abnormal Coolant Temperature Sensor P0117 1E-259
157-3 Abnormal Common Rail Pressure Sensor P0193 1E-294

157-4 Abnormal Common Rail Pressure Sensor P0192 1E-288
172-3 Abnormal Intake-Air Temperature Sensor P0113 1E-251
172-4 Abnormal Intake-Air Temperature Sensor P0112 1E-245
T5-6-100
ECM FAULT CODES 174, 636, 723, 10001
Fault Trouble Fault Code (Tech 2) Reference Page on

Code Engine Troubleshooting
Manual
174-3 Abnormal Fuel Temperature Sensor (Abnormal P0183 1E-280
High Voltage)
174-4 Abnormal Fuel Temperature Sensor (Abnormal P0182 1E-274
Low Voltage)
636-2 Abnormal Cam Angle Sensor (No Signal) P0340 1E-368
636-2 Abnormal Cam Angle Sensor (Abnormal P0341 1E-375

Signal)
636-7 Phase Mismatch of Cam Angle Sensor P1345 1E-524
723-2 Abnormal Crank Speed Sensor (No Signal) P0335 1E-355

723-2 Abnormal Crank Speed Sensor (Abnormal P0336 1E-362
Signal)
10001-3 Abnormal EGR Position (Brushless spec.) P0487 1E-391
IMPORTANT: When fault code 723-2 (abnormal

crank speed sensor) is displayed
and the engine does not start, the
cam angle sensor is faulty although
fault codes 636-2 (abnormal cam
angle sensor) and 636-7 (phase
mismatch of cam angle sensor) are
not displayed.
T5-6-101
ECM, EXTERNAL DEVICE SYSTEM
ECM FAULT CODES 651, 652, 653, 654, 655, 656, 1347, 10002
Fault Code Trouble Fault Code (Tech 2) Reference Page on Engine

Troubleshooting Manual
651-3 Open Circuit in Injection Nozzle ＃1 P0201 1E-301
Drive System
Drive System
Drive System
Drive System
1347-0 Open Circuit in Suction Control Valve P0090 1E-225
Drive System, Shorted Circuit in + B or
GND
10002-2 Abnormal EGR Valve Control P0488 1E-397
T5-6-102
ECM, FUEL SYSTEM
ECM FAULT CODES 157, 633, 1239, 1240

157-0 Abnormal Common Rail Pressure P0088 1E-215
(First Stage)
(Second Stage)
(Pump Over-Pressure)
633-7 Pressure Limiter Open P1095 1E-443
1239-1 No Pressure to Pump (Fuel Leakage) P0087 1E-207
1240-1 No Pressure to Pump (Fuel Leakage) P1093 1E-434
T5-6-103
ECM, ENGINE PROTECTION
ECM FAULT CODES 110, 190

110-0 Overheating P1173 1E-466
190-0 Overrunning P0219 1E-339
T5-6-104
ECM, ENGINE PROTECTION
ECM FAULT CODES 987, 1485

987-3 Abnormal Check Engine Lamp P0650 1E-429
1485-2 Abnormal Main Relay System (None) P1625 1E-529
T5-6-105
ECM, INTERNAL CIRCUIT SYSTEM
ECM FAULT CODES 628, 1077, 1079, 1080, 10003, 10004, 10005

628-2 Abnormal ROM P0601 1E-417
1077-2 Abnormal IC for CPU Watching P0606 1E-421
1079-2 Abnormal 5 V Power Source 1 Voltage P1631 1E-538
10003-2 Abnormal Injection Nozzle Common 1 P1261 1E-476
Drive System
10004-2 Abnormal Injection Nozzle Common 2 P1262 1E-487
Drive System
10005-1 Abnormal Charge Circuit (Bank 1) P0611 1E-423
T5-6-106
ECM FAULT CODES 10006, 10007, 10008, 10009, 10010, 10011, 10013

10006-1 Abnormal Charge Circuit (Bank 2) P0612 1E-426
10007-2 Abnormal CPU P0606 1E-421
10008-2 Abnormal A/D Conversion P1630 1E-536
10013-2 Abnormal EEPROM P0603 1E-419
T5-6-107
ECM, COMMUNICATION SYSETEM
ECM FAULT CODE 639

639-2 Abnormal CAN Bus Line U2104 1E-553
639-3 Abnormal CAN Time Out U2106 1E-558
T5-6-108
ICF, SATELLITE TERMINAL FAULT CODES 14000 to 14003
Fault Code Trouble Remedy

14000-2 Abnormal CAN Communication Execute retry B in self-diagnosing.
item.
• Check the CAN communication line (harness).
14001-2 ICF: Flash Memory: Read / Write Error Execute retry B in self-diagnosing and execute the following
14002-2 ICF: External RAM: Read / Write Error item.
• Execute “Information C/U: Initialize”.
14003-2 ICF: EEPROM: Sum Check Error Execute retry B in self-diagnosing.
item.
• Execute “Control Data: Initialize”.
• Execute “Enter Model and Serial No.”.
T5-6-109
Information C/U: Initialize


controller Password
Machinery Co., ltd
+ ICF Controller
Save Data Check
ESC ESC Start Back

Push OK. Setup. Push Information C/U: Initialize.
・ ICF + Information C/U: Various + Information C/U: Initialize

Controller Ver.: XXYY Setup To the
・ Satellite Terminal Enter Model and Serial
+ Data Download + lower
Is it correct?
OK ESC ESC ESC
Screen

Push ESC and return to Push OK and return to Information
C/U: Various Setup Screen. Push ESC and return to Main
Information C/U: Various Setup Menu Screen.
Screen.
Information C/U: Initialize Select Item

Is operation data erased? Initialization has been
completed.
ESC
+ Control Data: initialize
Init ESC OK ESC
Information C/U: Initialize Screen

Screen
T5-6-110
Control Data: Initialize


controller Password
Machinery Co., ltd
+ ICF Controller
Save Data Check
ESC ESC Start Back

Push OK. Setup. Push Control Data: Initialize.

・ Satellite Terminal Enter Model and Serial
+ Data Download + lower
Is it correct?
OK ESC ESC ESC
Screen

Push ESC and return to Push OK and return to Information
Information C/U: Various Setup C/U: Various Setup Screen. Push ESC and return to Main
Control Data: Initialize Select Item

Is control data initialized? Initialization has been
completed.
ESC
Init ESC OK ESC

Screen
T5-6-111
Enter Model and Serial No.


controller Password
+ Engine Controller
To the
Machinery Co., ltd
+ ICF Controller
Save Data Check
ESC ESC Start Back

Push OK. Setup. Push Enter Model and Serial No.

Enter Model and Serial
・ Satellite Terminal + Data Download + lower
No.
Controller Ver.: XXYY
Is it correct?
OK ESC ESC ESC
Screen
After inputting model and serial No.,

Push Exec, and model and serial push OK and return to Enter Model
No. can be input. and Serial No. Screen.
Push ESC and return to Push ESC and return to Information
Information C/U: Various Setup C/U: Various Setup Screen. Push ESC and return to Main
Enter Model and Serial No. Enter Model and Serial No. Select Item
Model 01G6 + Information C/U: Initialize

Model |
Ex. Mach.No.(HCM1G600P12 Enter Model and Serial
3456) Model(01G6) +
Exec ESC No.
Serial No. 900005 Serial No.
ESC OK
Ex. Mach.No.(HCM1G600P12 + Control Data: Initialize
3456) Serial No.(123456)
Exec ESC OK ESC ESC
Enter Model and Serial No. Information C/U: Various Setup

Screen
T5-6-112
ICF, SATELLITE TERMINAL FAULT CODES 14006, 14008, 14100 to 14106

14006-2 ICF: Satellite Communication Execute retry B in self-diagnosing.
Terminal: Communication Error If this error code is displayed after re-try, check the following
item.
Check the communication line.
Check the power source line of satellite terminal.
Check the fuse.

14008-2 ICF: Abnormal Internal RAM Execute retry B in self-diagnosing.
If this error code is displayed after re-try, replace the
controller.
Abnormal EEPROM
Abnormal IB/OB Queue
14102-2 Satellite Communication Terminal: Check the communication aerial of satellite terminal. (Refer
Abnormal Local Loup Back to T5-6-113.)
The satellite is not found.
14104-2 Satellite Communication Terminal: Execute retry B in self-diagnosing.
Fail 1 of Remote Loup Back If this error code is displayed after re-try, replace the
Fail 2 of Remote Loup Back
mismatched.
Fault Code 14006-2
• Check the communication line Connector (Harness end of connector viewed from the
1. Check for continuity between terminal #A8 of open end)
harness end of connector ICF-A in ICF and
terminal #10 of harness end of connector A in
satellite terminal.
2. Check for continuity between terminal #A9 of ICF
Connector ICF-A
harness end of connector ICF-A in ICF and #A8
terminal #20 of harness end of connector A in #A9
satellite terminal.
3. Check for continuity between terminal #A31 of
#A31
harness end of connector ICF-A in ICF and
terminal #2 of harness end of connector B in Satellite
Connector A
satellite terminal.
• Check the power source line of satellite terminal
1. Check the battery power 10 9 8 7 6 5 4 3 2 1
Check voltage between terminal #2 of harness 20 19 18 17 16 15 14 13 12 11
end of connector A in satellite terminal and
machine is 24 V. Satellite
2. Check the main power Connector B
With the key switch ON, check voltage between
terminal #1 of harness end of connector A in 8 7 6 5 4 3 2 1
satellite terminal and machine is 24 V. 16 15 14 13 12 11 10 9
3. Check the ground power
#12 of harness end of connector A in satellite
terminal.
T5-6-113
Fault Codes 14102-2, 14103-2
Communication
Aerial
(GPS Aerial)
Satellite T1V1-05-07-001
Terminal
Communication
Aerial
(GPS Aerial)
T1V1-05-06-004
T5-6-114
MONITOR UNIT FAULT CODE 13303
13303-2 Abnormal Thermister Temperature Cool the monitor unit until temperature inside the monitor unit
becomes less than 85 °C.
The screen of monitor unit becomes dark.
YES Normal.
Cool monitor unit. Check

YES
if the screen of monitor
unit becomes normal.
Faulty monitor unit.
Check if temperature
NO
around monitor unit is
high.
Faulty monitor unit.

NO
T5-6-115

13304-2 Abnormal REG Input H Level Refer to the following.
NOTE: As terminal L in the regulator is a

waterproof type connector, it is difficult to
measure voltage. Measure voltage at
terminal R in starter relay 2. Check for
continuity at terminal R in starter relay 2
and terminal L in regulator.
Less than 33.5 V Faulty monitor unit.

Less than Measure voltage at
33.5 V terminal #C7 of
connector monitor-C.
· Engine: Running between terminal L in
Measure voltage at 33.5 V or higher regulator and monitor
terminal L in unit.
regulator.
Faulty regulator or faulty
alternator.
33.5 V or higher

open end)
Starter Relay 2
E
S R
Monitor Unit
Connector Monitor-C
6 1
12 7
#C7
T5-6-116
MONITOR UNIT FAULT CODES 13306, 13308
13306-2 Abnormal EEPROM If this error code is displayed after re-try, replace the monitor
unit.
13308-2 Abnormal CAN Communication Refer to “Check CAN Harness” (T5-6-54).
T5-6-117
13310-2 Shorted Circuit in Coolant Check the coolant temperature sensor and harness.
Temperature Sensor
With terminal of coolant

temperature sensor Shorted circuit in harness
YES between monitor unit and
disconnected, disconnect
connector monitor-C in sensor.
YES
monitor unit.
Check for continuity between
terminal #C8 of harness end Faulty monitor unit.
Check if resistance of of connector in monitor unit NO
coolant temperature and machine.
sensor is specification.
Faulty coolant temperature

NO sensor.
Coolant Temperature Sensor

Coolant Temperature Resistance
(ﾟ C) (kΩ)
25 7.6±0.76
40 4.0±0.35
50 2.7±0.22
80 0.92±0.07
95 0.56±0.04
105 0.42±0.03
120 0.28±0.01

open end)
Monitor Unit
Connector Monitor-C
·
·6 · · · ·1
·1 · · · · ·7
#C8
T5-6-118
13311-3 Shorted Circuit in Fuel Level Sensor Check the fuel level sensor and harness.
13311-4 Open Circuit in Fuel Level Sensor Check the fuel level sensor and harness.
Shorted circuit in harness

YES
With connector of fuel between monitor unit and
level sensor sensor.
disconnected, disconnect
connector monitor-C in
YES monitor unit.
Check for continuity Connect terminal #1 of
between terminal #C2 of harness end of YES Faulty monitor unit.
harness end of connector in fuel level
connector in monitor unit sensor to machine.
and machine. Check for continuity
Check if resistance of NO between terminal #C2 of
fuel level sensor is harness end of Open circuit in harness
specification. connector in monitor unit NO between monitor unit and
and machine. sensor.
Faulty fuel level sensor.

NO
Fuel Level Sensor
Float Float Position Resistance (Ω)

+0
Upper Limit (FULL) 10 -4
FULL
3/4 26
R370 1/2 38±5
257 mm 3/4 1/4 53
Alarm Level 85±3
93 mm
+10
Lower Limit (EMPTY) 90 -0
70.5 mm
204 mm 1/2 Connector (Harness end of connector viewed from the

open end)
1/4 Monitor Unit
338 mm Connector Moniter-C Fuel Sensor
EMPTY ·
·6 · · · ·1 1 2
·1 · · · · ·7
T178-05-05-001
T5-6-119
PILOT SHUT-OFF LEVER ALARM
Pilot shut-off lever alarm is displayed on the
monitor unit screen.
YES Faulty pilot shut-off

switch.
Check if pilot shut-off
switch is bent or
damaged.
Faulty harness.
NO
Pilot Shut-Off Pilot Shut-Off

Lever Switch
T1V1-05-06-005
T5-6-120
TROUBLESHOOTING / Troubleshooting B
TROUBLESHOOTING B PROCEDURE
Apply troubleshooting B procedure when no fault code
is displayed on the service menu in monitor unit and
the diagnosing by Dr. ZX although the machine
operation is abnormal.
On the front section pages of this group are the tables
indicating the relationship between machine trouble
symptoms and related parts which may cause such
trouble if failed.
Start the troubleshooting with more probable causes
selected by referring to these tables.
• How to Read the Troubleshoting Flow Charts
YES(OK)
(2)
• After checking or measuring item (1), select either YES (OK) or
・ (1) NO (NOT OK) and proceed to item (2) or (3), as appropriate.
(3)
NO(NOT OK)
・ • Special instructions or reference item are indicated in the spaces under the box.
Incorrect measuring or checking methods will render troubleshooting impossible,
· Key switch: ON and may damage components as well.
• Explanation of how to use test harness kit required. Refer to “Electrical System
・
Inspection” Group (Group 8) in this section.
・ • Use the service menu (diagnosing system/monitoring ) in monitor unit or the

diagnosing system / monitor function in Dr. ZX.
・ • Causes are stated in a thick-line box. Scanning through thick-line boxes, possible
causes can be seen without going through the flow chart.
T5-7-1
RELATIONSHIP BETWEEN MACHINE
TROUBLE SYMPTOMS AND RELATED
PARTS
This table indicates the relationship between machine
trouble symptoms and the potential problem parts,
which may cause trouble if failed, and the evaluation
methods of these components.
Item Symptoms in control Symptoms in machine
Parts Function system when trouble operation when trouble
occurs. occurs.
Engine Control Dial • Instructs engine target • Engine speed is kept at idling • Engine speed is kept at idling
speed. speed when trouble occurs speed when trouble occurs
with key ON. with key ON.
• Engine speed is kept at • Engine speed is kept at
speed just before trouble speed just before trouble oc-
occurred when trouble occurred when trouble occurs
curs during operation. during operation.
Pump Control Pressure • Monitors pump control pres- • E mode control • E mode control
sure in order to control travel In normal, P speed is re- In normal, P speed is re-
Sensor motor swash angle control. turned whenever operating. P turned whenever operating. P
speed is not returned when speed is not returned when
this trouble opccurs. this trouble opccurs.
• Heater Control • As the machine is kept to
Heater control is ineffective. travel at slow speed, speed
• Travel motor displacement does not change into fast
angle control automatically.
The machine travels at slow
speed.
Pump 1 Delivery Pres- • Monitors pump delivery • HP mode control • During combined operation of
sure Sensor pressure in order to control Engine speed does not in- boom raise and arm roll-in or
HP mode, slow speed torque crease. of arm roll-in and swing, arm
increase, auto-power lift and • Travel HP mode control speed is slow.
travel motor swash angle This control is operated by • During boom raise operation,
controls. pressure except P1. lifting power is weak.
• P-Q torque correction • As the machine is kept to
Torque does not increase. travel at slow speed, speed
• Travel torque-up control does not change into fast.
The machine may mistrack.
• Bom regeneration control
Arm regeneration control is
ineffective.
• Digging regeneration control
Digging regeneration control
is ineffective.
• Auto-power lift control.
Auto-power lift control is in-
effective.
• Travel motor displacement
angle control.
speed.
T5-7-2
Descriptions of Control
Evaluation by Evaluation by Monitor Evaluation by using
NOTE (Operational Principle
MC Fault Code Function Test Harness
Section in T/M)
11101-3, 11101-4 Monitor Item: Target T2-2
engine speed, Dial angle
(Possible to display by
service menu and moni- - -
toring in monitor unit)
11206-3, 11206-4, Monitor Item: Pump 1 T2-2

pump control pressure,
11208-3, 11208-4
Pump 2 pump control
pressure (Possible to dis-
play by service menu and
monitoring in monitor unit) - -
11200-3, 11200-4 Monitor Item: Pump 1 T2-2

monitoring in monitor unit)
- -
T5-7-3

occurs. occurs.
Pump 2 Delivery Pres- • Monitors pump delivery • HP mode control • During combined operation of
sure Sensor pressure in order to control Engine speed does not boom raise and arm roll-in or
HP mode, slow speed torque increase. of arm roll-in and swing, arm
increase, arm flow rate, arm • Travel HP mode control speed is slow.
regeneration and travel mo- This control is operated by • As the machine is kept to
tor displacement angle con- pressure except P2. travel at slow speed, speed
trols. • P-Q torque correction does not change into fast.
Torque does not increase.
• Travel torque-up control
The machine mistrackes.
• Arm regeneration control
Arm regeneration control is
ineffective.
is ineffective.
angle control
speed.
Pump 3 Delivery Pres- • Monitors pump delivery • Engine stalls if pump 3 is • Engine stalls if pump 3 is
sure Sensor (Optional) pressure in order to control loaded (pump torque is loaded (pump torque is
pump 3 torque decrease increased). increased).
control.
T5-7-4
Section in T/M)
11202-3, 11202-4 Monitor Item: Pump 2 T2-2
monitoring in monitor unit)
- -
T2-2
- - - -
T5-7-5

occurs. occurs.
Pressure Sensor (Travel) • Monitors travel pilot pressure • Idle speed-up control • When the machine travels at
in order to control auto-idle, Engine speed does not idle speed, engine speed is
idle speed-up, engine speed change into idle speed-up not changed into idle
automatic increase at travel speed when traveling. speed-up speed.
(ZX270-3 class only), slow • Auto-idle control • Although the machine travels,
speed torque increase and Although the machine trav- engine speed is kept at
travel motor displacement els, auto-idle is not released. auto-idle speed.
angle controls. • ECO control • Although the machine travels,
Although the machine trav- engine speed does not in-
els, engine speed does not crease.
increase. • As the machine is kept to
• Travel HP mode control travel at slow speed, speed
Travel HP mode control is does not change into fast.
ineffective. • During combined operation of
• Operation torque decrease attachment and travel, the
control machine mistracks.
Operation torque decrease • The travel alarm is kept to
control is ineffective. ring as for the machine
• Travel torque-up control equipped with travel alarm
Travel torque-up control is (optional).
ineffective.
angle control
speed.
• Attachment flow rate control
During combined operation
of secondary crusher or pri-
mary crusher and travel, at-
tachment operation speed
may become slow.
• Travel alarm (optional)
control
Travel alarm is kept ON.
T5-7-6
Section in T/M)
11304-3, 11304-4 Monitor Item: Travel con- Judge if pressure T2-2
trol pressure (Possible to sensor is faulty or
display by service menu port is clogged by
and monitoring in monitor switching pressure
unit) sensor with other
Monitor pressure change pressure sensor.
while traveling machine.
T5-7-7

occurs. occurs.
Pressure Sensor • Monitors front attachment • Idle speed-up control • When the front attachment is
(Front Attachment) pilot pressure in order to Engine speed does not operated at idle speed, en-
control auto-idle, idle change into idle speed-up gine speed is not changed
speed-up and engine speed speed when operating front into idle speed-up speed.
automatic increase at travel attachment. • When the front attachment is
(ZX270-3 class only) con- • Auto-idle control operated, engine speed is
trols. Although the front attach- kept at auto-idle speed.
ment is operated, auto-idle is • When the front attachment is
not released. operated, engine speed does
• ECO control not increase.
Although the front attach- • Although the front attachment
ment is operated, engine is operated, the machine
speed does not increase. travels at fast speed.
• Operation torque decrease
control
Operation torque decrease
control is ineffective.
• Travel torque-up control
Although the front attach-
ment is operated, travel
torque-up control is not re-
leased.
angle control
Although the front attach-
ment is operated, the ma-
chine travels at fast speed.
Pressure Sensor (Swing) • Monitors swing pilot pressure • Arm regeneration control • Arm speed is slow during
in order to control arm flow During combined operation combined operation of arm
rate and arm regeneration of arm roll-in and swing, arm roll-in and swing.
controls. regeneration is reduced. • The swing alarm is kept to
• Swing alarm (optional) con- ring when swing alarm is ef-
trol fective as for the machine
Swing alarm is kept ON. equipped with swing alarm
(optional).
T5-7-8
Section in T/M)
11307-3, 11307-4 Monitor Item: Front at- Judge if pressure T2-2
tachment operation (Pos- sensor is faulty or
sible to display by service port is clogged by
menu and monitoring in switching pressure
monitor unit) sensor with other
while operating front at-
tachment.
11301-3, 11301-4 Monitor Item: Swing con- Judge if pressure T2-2

trol pressure (Possible to sensor is faulty or
unit) - sensor with other
while swinging upper-
structure.
T5-7-9

occurs. occurs.
Pressure Sensor • Monitors boom raise pilot • HP mode control • When operating boom raise
(Boom Raise) pressure in order to control Engine speed does not in- during HP mode control, en-
HP mode, arm regeneration crease when operating boom gine speed does not increase.
and auto-power lift controls. raise. • During combined operation of
• Arm regeneration control boom raise and arm roll-in,
Arm regeneration is arm speed is slow.
ineffective during combined • During boom raise operation,
operation of boom raise and lifting power is weak.
arm roll-in.
is ineffective.
angle control
speed.
• Auto-power lift control
The operating boom rasie,
pressure does not increase.
• Attachment flow rate control
During combined operation
of attachment and boom
raise, attachment operation
speed is fast.
• Boom limit is operated.
T5-7-10
Section in T/M)
11302-3, 11302-4 Monitor Item: Boom raise Judge if pressure T2-2
pilot pressure (Possible to sensor is faulty or
while raising boom.
T5-7-11

occurs. occurs.
Pressure Sensor • Monitors arm roll-in pilot • HP mode control • When operating arm roll-in
(Arm Roll-In) pressure in order to control Engine speed does not with the HP mode switch ON,
HP mode, arm flow rate, and increase when operating arm engine speed does not in-
arm regeneration controls. roll-in. crease.
• Arm regeneration control • During combined operation of
Arm regeneration is not op- arm roll-in and swing, arm
erated during combined op- speed is slow.
eration of arm roll-in and
swing.
Arm operation speed is
slightly slow when operating
digging during combined op-
eration of boom raise and
arm roll-in.
• Auto-power lift control
Pressure increases when
operating digging during
combined operation of boom
raise and arm roll-in.
Pressure Sensor • Monitors attachment pilot • Attachment Open part: • During combined operation of
(Auxiliary) (Optional) pressure when attachment is Maximum attachment and front attach-
installed in order to control • Pump 1, 2 flow rate limits are ment, front attachment speed
attachment operation speed ineffective. is slow.
increase, pump 1 flow rate • Pump 1, 2 flow rates are not
limit, pump 2 flow rate limit limited at attachment mode.
and auxiliary flow rate con-
trols.
Torque Control Solenoid • Supplies control pressure to • High current: Pump torque is • High current: If pump torque
Valve pumps 1 and 2 in order to kept maximum. The engine is maximum at low idle, the
control speed sensing and stalls or llug-down is re- engine stalls or llug-down oc-
slow speed torque increase markable at high loaded. curs.
controls. • Low current: Pump torque is • Low current: The machine
kept minimum. operation is totally slow.
T5-7-12
Section in T/M)
11303-3, 11303-4 Monitor Item: Arm roll-In Judge if pressure T2-2
pilot pressure (Possible to sensor is faulty or
while rolling arm in.
Monitor Item: ATT control Judge if pressure T2-2

pressure (Possible to dis- sensor is faulty or
play by service menu and port is clogged by
monitoring in monitor unit) switching pressure
- Monitor pressure change - sensor with other
while operating attach- pressure sensor.
ment.
11401-2, 11401-3, Monitor Item: Pump T2-2

torque proportional sole-
11401-4
noid valve output
- -
T5-7-13

occurs. occurs.
Solenoid Valve Unit (SG) • Temporarily increases main • High current: Pressure is • High current: Pressure is
relief valve relief pressure in kept increasing. kept increasing according to
power digging and • Low current: Pressure cannot the valve open condition.
auto-power lift control. increase. Therefore, power increases
as for all operations.
• Low current: Relief pressure:
34 MPa (350 kgf/ cm2) is
kept. Therefore, although the
power digging switch is
pushed, relief pressure does
not increase. Power does not
increase.
Solenoid Valve Unit (SF) • Routes return oil from boom • High current: Digging • High current: During
cylinder rod side to arm regeneration control is combined operation of boom
cylinder bottom side during always effective. raise and arm roll-in with
digging operation and • Low current: Digging suspended load and fine
increases arm speed. regeneration control is operation, boom does not
always ineffective. raise easily.
• Low current: During digging
operation, arm operation
speed is slow. (Slowdown is
not remarkable.)
Solenoid Valve Unit (SC) • Routes return oil from arm • High current: Digging power • High current: Digging power
cylinder rod side to arm (arm) becomes weak. (arm) becomes weak.
cylinder bottom side when • Low current: Arm • Low current: During
rolling arm in and increases regeneration is always combined operation of boom
arm speed. ineffective. raise and arm roll-in above
the ground, boom does not
raise easily and maximum
arm roll-in operation speed is
slow.
T5-7-14
Section in T/M)
11404-2, 11404-3, Monitor Item: Power dig- Install lamp harness (ST Proportional sole- T2-2
ging control pressure 7226). Check output signals noid valve is used as
11404-4 from MC and harness condi- an ON/OFF valve.
tion. When power digging
switch is pushed or
released and lamp
comes ON, harness
is normal. If lamp
goes OFF, it may be
due to open circuit in
harness.
11402-2, 11402-3, Monitor Item: Digging re- Install lamp harness (ST T2-2
generative valve 7226). Check output signals
1402-4 from MC and harness condi-
tion.
11403-2, 11403-3, Monitor Item: Arm regen- Install lamp harness (ST T2-2
erative proportional sole- 7226). Check output signals
noid valve output
tion.
-
T5-7-15

occurs. occurs.
Solenoid Valve Unit (SI) • When pump delivery • High current: Travel motor is • High current: Travel motor is
pressure is low in fast travel always operated at fast always operated at fast
mode, travel motor swash speed. speed.
angle is reduced and • Low current: Travel motor is • Low current: Travel motor is
increases travel speed. always operated at slow always operated at slow
speed. speed.
Max. Pump 1 Flow Rate • Limits maximum pump 1 flow • High current: Pump 1 flow • High current: The machine
Limit Solenoid Valve (Op- rate when operating rate becomes minimum. mistracks. Boom raise
attachment. • Low current: Pump 1 flow operation speed is slow. Arm
tional) rate does not decrease. roll-out and roll-in operation
Pump 1 attachment flow rate speeds are slow. Bucket
cannot be controlled. roll-in and roll-put operation
speeds are slow.
• Low current: Attachment flow
rate cannot be controlled.
Max. Pump 2 Flow Rate • Limits maximum pump 2 flow • High current: Pump 2 flow • High current: The machine
Limit Solenoid Valve rate when operating rate becomes minimum. mistracks. Boom raise
attachment. • Low current: Pump 2 flow operation speed is slow. Arm
rate does not decrease. roll-out and roll-in operation
speeds are slow. Swing
operation speed is slow.
• Low current: Attachment flow
rate cannot be controlled.
T5-7-16
Section in T/M)
11405-2, 11405-3, Monitor Item: Digging re- Install lamp harness (ST T2-2
generative valve 7226). Check output signals
tion. -
T2-2
- - - -
11400-2, 11400-3, T2-2

11400-4
- - -
T5-7-17

occurs. occurs.
Auxiliary Flow Rate Control • Restricts flow rate to auxiliary • If auxiliary flow rate control • High current: If valve is bound
Solenoid Valve (Optional) spool during combined solenoid valve is not fully closed, attachment
operation and improves activated, pressure at output speed becomes slow during
operability. port becomes 0 MPa (0 single operation.
kgf/cm2). • Low current: If valve is bound
fully open, boom does not
raise during 3-combined
operation of boom raise.
Auxiliary Flow Combining • Activates during auxiliary • If auxiliary flow combining • Speed does not increase
Solenoid Valve (Optional) operation and shifts spool in solenoid valve is not during single operation of
auxiliary flow combining activated, pressure at output attachment.
valve. port becomes 0 MPa (0
kgf/cm2) when operating
attachment.
Selector Valve Control • Activates when attachment • If selector valve control • Breaker stroke becomes few.
Solenoid Valve (Optional) “selector valve returning to solenoid valve is not
hydraulic oil tank” is selected activated, pressure at output
and shifts selector valve port becomes 0 MPa (0
spool. kgf/cm2) when attachment
“selector valve returning to
hydraulic oil tank” is
selected.
Accumulator Control So- • Activates when attachment • If accumulator control • When NPK breaker is used,
lenoid Valve (Optional) “accumulator ON” is selected solenoid valve is not hydraulic pulsation (hose
and shifts accumulator activated, pressure at output vibration) becomes big.
control valve spool. port becomes 0 MPa (0
kgf/cm2) when attachment
“accumulator ON” is
selected.
T5-7-18
Section in T/M)
T2-2
- - - -
T2-2
- - - -
When pedal is de- T2-2

pressed, pressure in
the right piping hose
occurs.
- - -
T2-2
- - - -
T5-7-19

occurs. occurs.
Secondary Pilot Relief • Activates when attachment • If secondary pilot relief • Relief set-pressure in
Pressure Control Solenoid “secondary pilot relief pressure control solenoid auxiliary circuit does not
pressure ON” is selected and valve is not activated, decrease.
Valve (Optional) shifts secondary pilot relief pressure at output port
pressure control valve spool. becomes 0 MPa (0 kgf/cm2)
when attachment “secondary
pilot relief pressure ON” is
selected.
Oil Temperature Sensor • Monitors hydraulic oil • Auto-warming control • When oil temperature is
temperature in order to Auto-warming control is lower than 0 °C,
control auto-warming control. ineffective. auto-warming up control is
not operated.
Power Digging Switch • Activates power digging • Open circuit: Pressure does • Power digging control is not
control. not increase. operated if open circuit or
• Shorted circuit: Pressure shorted circuit occurs.
ON: 0V→Increasing pressure does not increase for 8
OFF: 5V→ Not increasing seconds after the key switch
pressure is turned ON.
Travel Mode Switch • Shifts travel mode. • Open circuit in switch: Travel • Even if travel mode switch is
speed remains unchanged in turned to the FAST position,
Fast mode: 0V slow mode (5V). fast travel mode cannot be
Slow mode: 5V • Shorted circuit in switch: selected.
Travel speed remains • Even if travel mode switch is
unchanged in auto-second turned to the SLOW position,
gear (0 V). travel mode is turned to the
auto-second gear.
MC • Controls engine, pump and • Depending on trouble • Even if engine starts, engine
valve operations. situations, control system speed remains in idle speed.
malfunction may differ. (The • As pump displacement is
following symptoms in kept at minimum, all
machine operation indicates operation speeds are slow.
that MC logic circuit has
failed.)
T5-7-20
Section in T/M)
T2-2
- - - -
11901-3, 11901-4 Monitor Item: Hydraulic oil T2-2

temperature
- -
Monitor Item: Power Dig- T2-2

ging Switch
- - -
Monitor Item: Travel Mode T2-2
- - -
11000-2, 11001-2, Before suspecting a T2-2

failure in MC, check
11002-2, 11003-3
fuses in control sys-
tem. If any sensor in
- - 5 V system is
shorted circuit, fault
codes of all sensor
is displayed.
T5-7-21

occurs. occurs.
Auto-Idle Switch • Activates auto-idle. • Open circuit: Auto-idle is not • Open circuit: Auto-idle is not
ON: 0 V → Auto-idle control operated. operated.
is operated. • Shorted circuit: Even if • Shorted circuit: Even if
OFF: 5 V → Auto-idle is not auto-idle switch is in OFF auto-idle switch is in OFF
operated. position, auto-idle control is position, auto-idle control is
always operated. always operated.
Power Mode Switch • Activates HP mode control. • Open circuit: Even if HP • Open circuit: Even if HP
(HP Mode) mode is selected, HP mode mode is selected, HP mode
ON: 0 V → HP mode control is not operated. is not operated.
is operated. • Shorted circuit: Even if HP • Shorted circuit: Even if HP
OFF: 5 V → Normal. mode switch is turned OFF, mode switch is turned OFF,
HP mode is continued. HP mode is continued.
Attachment speed increase Attachment speed increase
control (optional) becomes control (optional) becomes
ineffective. ineffective.
Power Mode Switch • Selects E mode. • Open circuit: Even if E mode • Open circuit: Even if E mode
(E Mode) is selected, engine speed is selected, engine speed
ON: 0 V → E mode does not decrease with the does not decrease with the
OFF: 5 V → Normal. control lever in neutral. When control lever in neutral. When
E mode is selected and E mode is selected and
engine is operated at full engine is operated at full
speed with light load, engine speed with light load, engine
speed does not increase. speed does not increase.
• Shorted circuit: When the • Shorted circuit: When the
control lever is in neutral and control lever is in neutral and
the engine control dial is at the engine control dial is at
FAT idle position and even if FAT idle position and even if
the power mode switch is the power mode switch is
shifted from E mode to P shifted from E mode to P
mode, engine speed does mode, engine speed does
not increase. not increase.
T5-7-22
Section in T/M)
T2-2
- - - -
Monitor Item: E/P/HP T2-2

mode switch
- - -
Monitor Item: E/P/HP T2-2

mode switch
- - -
T5-7-23

occurs. occurs.
Arm 2 Flow Rate Control • Be shifted by pilot pressure • If spool is bound or spring is • If fully opened: Boom raise
Valve from solenoid valve unit broken, orifice does not speed is slow.
(SC). change • If fully closed: Arm roll-in
• Ensures boom raise speed speed is slow during arm
during combined operation of level crowd operation.
boom and arm.
Flow Combiner Valve • Supplies oil to both right and • During combined operation • While traveling and when
left travel spools from pump of travel and front/swing, oil front/swing lever is operated,
1 during combined operation is not supplied to left travel machine mistracks to the left.
of travel and front/swing. spool, or insufficient oil is
supplied to left travel spool.
Arm 1 Flow Rate Control • Be shifted by pilot pressure • If spool is bound or spring is • If fully opened: swing power
Valve from arm flow rate control broken, orifice does not is lack.
valve in signal control valve. change. • If fully closed: Arm roll-in
• Ensures swing power. speed is slow during arm
level crowd operation.
Bucket Flow Rate Control • Restricts oil flow to bucket • If selector valve is bound • If poppet valve is bound at
Valve during 3-combined operation with selector valve activated, fully closed position or if
of bucket, arm roll-in and bucket circuit is always selector valve is bound when
boom raise, and allows boom restricted. poppet valve is fully closed,
to raise. bucket speed becomes slow.
• If poppet valve is bound at
fully open position or if
selector valve is bound when
poppet valve is fully open,
boom does not raise during
3-combined operation of
bucket, arm roll-in and boom
raise.
T5-7-24
Section in T/M)
T3-3
- - - -
T3-3
- - - -
T3-3
- - - -
T3-3
- - - -
T5-7-25

occurs. occurs.
Auxiliary Flow Rate • Be shifted by pilot pressure • If spool is bound or spring is • If bound at fully closed
Control Valve from auxiliary flow rate broken, orifice does not position, attachment speed
control solenoid valve. change. becomes slow.
• If bound at fully open
position, boom does not
raise during 3-combined
operation of swing, arm
roll-in and boom raise.
Boom Regenerative Valve • Routes return oil from boom • If check valve is kept closed, • If check valve is kept closed,
cylinder bottom side to rod boom is not smoothly boom is not smoothly
side and prevents boom lowered. lowered.
cylinder hesitation. • If check valve is kept open, • If check valve is kept open,
machine cannot be raised off machine cannot be raised off
ground with front attachment. ground with front attachment.
Arm Regenerative Valve • Be shifted by pilot pressure • Arm regenerative function is • Arm speed is extremely slow
from solenoid valve unit not operated. during arm level crowd
(SC). operation while arm
• Routes return oil from arm regenerative valve is kept
cylinder rod side to bottom closed.
side and increases arm • The lever operated first is
speed. given priority during
combined operation of arm
roll-in and swing while arm
regenerative valve is kept
open.
Bucket Regenerative • Routes return oil from bucket • If check valve is kept closed, • If check valve is kept closed,
Valve cylinder rod side to bottom bucket is not smoothly rolled bucket is not smoothly rolled
side and prevents bucket in. in.
cylinder hesitation. • If check valve is kept open, • If check valve is kept open,
bucket power is weak. bucket power is weak.
T5-7-26
Section in T/M)
T3-3
- - - -
T3-3
- - - -
T3-3
- - - -
T3-3
- - - -
T5-7-27

occurs. occurs.
Arm Anti-Drift Valve • Forcibly open check valve in • If switch valve is bound, • If check valve is kept closed,
arm roll-in return circuit and check valve does not open. arm roll-in speed becomes
allows arm to move only slow.
when arm is rolled in. • If check valve is kept open,
Prevents arm from drifting front attachment drift
due to oil leaks in control increases due to oil leaks in
valve. control valve.
• Arm moves jerky or arm
speed becomes slow
depending on valve bound
conditions.
Boom Anti-Drift Valve • Forcibly open check valve in • If switch valve is bound, • If check valve is kept closed,
boom lower return circuit and check valve does not open. boom does not lower.
allows boom to move only • If check valve is kept open,
when boom is lowered. front attachment drift
Prevents boom from drifting increases due to oil leaks in
due to oil leaks in control control valve.
valve. • Boom moves jerky or boom
speed becomes slow
depending on valve bound
conditions.
T5-7-28
Section in T/M)
T3-3
- - - -
T3-3
- - - -
T5-7-29

occurs. occurs.
Bypass Shut-Out Valve • Supplies pressure oil from • If spool is bound at fully • If spool is bound at fully
pump 1 to auxiliary spool open, single attachment open, single attachment
when auxiliary spool is operation speed becomes operation speed becomes
operated. slow. slow.
• Increases pump 1 pressure • If spool is bound at fully • If spool is bound at fully
when machine is raised off closed, main relief valve closed, main relief valve
the ground. continues to relieve with all continues to relieve with all
control levers in neutral. control levers in neutral.
• When all control levers are in • When all control levers are in
neutral, pump 1 pressure is neutral, pump 1 pressure is
higher than pump 2 pressure higher than pump 2 pressure
by depending on spool by depending on spool
bound condition. bound condition.
• If spool is bound at fully • If spool is bound at fully
closed, machine cannot be closed, machine cannot be
raised off the ground. raised off the ground.
T5-7-30
Section in T/M)
T3-3
- - - -
T5-7-31

occurs. occurs.
Pump 1 Flow Rate Con- • Supplies flow rate control • If spool is bound at fully • If spool is bound at fully
trol Valve pressure Pi to pump 1 open, even if control lever is open, even if control lever is
regulator in response to lever in neutral, pump 1 swash in neutral, pump 1 swash
stroke when boom angle is tilted to maximum. angle is tilted to maximum.
(raise/lower), arm (When traveling with travel (When traveling with travel
(roll-out/in), bucket levers held in half stroke, levers held in half stroke,
(roll-out/in), right travel or machine mistracks to the machine mistracks to the
auxiliary is operated. left.) left.)
open, pump 1 control open, pump 1 control
pressure sensor detects the pressure sensor detects the
maximum pressure. maximum pressure.
closed, even if control lever closed, even if control lever
is operated, pump 1 swash is operated, pump 1 swash
angle is tilted to minimum. angle is tilted to minimum.
(Right travel is not operated (Right travel is not operated
during single travel during single travel
operation. Bucket speed operation. Bucket speed
becomes very slow.) becomes very slow.)
pressure sensor cannot pressure sensor cannot
detect pump control detect pump control
pressure. pressure.
(Right travel does not run (Right travel does not run
fast with right track fast with right track
jacked-up.) jacked-up.)
T5-7-32
Section in T/M)
T3-6
- - - -
T5-7-33

occurs. occurs.
Pump 2 Flow Rate Con- • Supplies flow rate control • If spool is bound at fully • If spool is bound at fully
trol Valve pressure Pi to pump 2 open, even if control lever is open, even if control lever is
regulator in response to lever in neutral, pump 2 swash in neutral, pump 2 swash
stroke when boom angle is tilted to maximum. angle is tilted to maximum.
(raise/lower), arm (When traveling with travel (When traveling with travel
(roll-out/in), swing (right/left), levers held in half stroke, levers held in half stroke,
left travel or auxiliary is machine mistracks to the machine mistracks to the
operated. right.) right.)
pressure sensor detects the pressure sensor detects the
maximum pressure. maximum pressure.
closed, even if control lever closed, even if control lever
is operated, pump 2 swash is operated, pump 2 swash
angle is tilted to minimum. angle is tilted to minimum.
(Left travel is inoperable (Left travel is inoperable
during single travel during single travel
operation. Swing speed operation. Swing speed
becomes very slow.) becomes very slow.)
pressure sensor cannot pressure sensor cannot
detect pump control detect pump control
pressure. pressure.
(Left travel does not run fast (Left travel does not run fast
with left track jacked-up.) with left track jacked-up.)
Flow Combiner Valve • Be shifted by right travel pilot • If spool is bound at fully • If spool is bound at fully
Control Spool pressure and supplies open, when boom, arm, open, when boom, arm,
control pressure to flow bucket or swing is operated, bucket or swing is operated,
combiner valve in control flow combiner valve is flow combiner valve is
valve. shifted. shifted.
closed, when combined closed, when combined
operation of travel and operation of travel and
front/swing is made, machine front/swing is made, machine
mistracks to the left. (Left mistracks to the left. (Left
travel speed becomes slow.) travel speed becomes slow.)
T5-7-34
Section in T/M)
T3-6
- - - -
T3-6
- - - -
T5-7-35

occurs. occurs.
Swing Parking Brake • Be shifted by boom, arm, • If spool is bound at fully open, • If spool is bound at fully open,
Release Spool bucket or swing pilot swing parking brake is kept swing parking brake is kept
pressure and supplies swing released. (Machine vibrates released. (Machine vibrates
parking brake release while traveling.) while traveling.)
pressure. • If spool is bound at fully open, • If spool is bound at fully open,
pressure sensor (front pressure sensor (front
attachment) is always turned attachment) is always turned
into ON. into ON.
Thus, engine speed does not Thus, engine speed does not
decrease when control lever decrease when control lever
is in neutral during auto-idle is in neutral during auto-idle
control. control.
closed, swing parking brake is closed, swing parking brake is
kept applied. (Dragging is kept applied. (Dragging is
felt.) felt.)
closed, pressure sensor (front closed, pressure sensor (front
attachment) is always turned attachment) is always turned
into OFF. into OFF.
Thus, engine speed does not Thus, engine speed does not
increase when control lever is increase when control lever is
operated during auto-idle operated during auto-idle
control. control.
Bucket Flow Rate Control • Be shifted by arm roll-in pilot • If spool is bound at fully open, • If spool is bound at fully open,
Valve Control Spool pressure and supplies boom bucket speed becomes slow bucket speed becomes slow
raise pilot pressure to during combined operation of during combined operation of
bucket flow rate control boom raise and bucket. boom raise and bucket.
valve as control pressure. (Bucket flow rate control is (Bucket flow rate control is
ineffective.) ineffective.)
closed, boom does not raise closed, boom does not raise
during 3-combined operation during 3-combined operation
of bucket, arm roll-in and of bucket, arm roll-in and
boom raise. boom raise.
T5-7-36
Section in T/M)
T3-3
- - - -
T3-3
- - - -
T5-7-37

occurs. occurs.
Arm Flow Rate Control • Be shifted by arm roll-in pilot • If spool is bound at fully • If spool is bound at fully open,
Valve Control Spool pressure and supplies to arm open, arm speed decreases arm speed decreases during
flow rate control valve 1 on during single arm operation. single arm operation. (Arm
5-spool side in control valve (Arm flow rate control is flow rate control is always
as control pressure. always operated.) operated.)
closed, swing power closed, swing power becomes
becomes insufficient during insufficient during combined
combined operation of swing operation of swing and arm
and arm roll-in. (Arm flow roll-in. (Arm flow rate control
rate control is not operated.) is not operated.)
Digging Regenerative • Be shifted by pilot pressure • If valve is kept closed, arm • If valve is kept closed, arm
Valve from solenoid valve unit (SF). roll-in speed becomes slow roll-in speed becomes slow
• Routes return oil from boom during digging operation. during digging operation.
cylinder rod side to arm • If valve is kept open, arm • If valve is kept open, arm
cylinder bottom side and speed becomes fast. speed becomes fast.
increases arm speed. • Shock occurs during boom • Shock occurs during boom
raise operation. raise operation.
Boom Flow Rate Control • Be shifted by pilot pressure • If valve is at fully open, boom • If valve is at fully open, boom
Valve from boom lower meter-in cut lower speed becomes fast lower speed becomes fast
valve. during combined operation. during combined operation.
• Controls flow rate to boom 1 • If valve is at fully closed, • If valve is at fully closed,
spool during combined machine cannot be raised off machine cannot be raised off
operation and improves ground with front attachment. ground with front attachment.
combined operation.
T5-7-38
Section in T/M)
T3-6
- - - -
T3-3
- - - -
T3-3
- - - -
T5-7-39

occurs. occurs.
Boom Lower Meter-In Cut • Be shifted by return oil from • If valve is kept closed, as • If valve is kept closed, as
Valve boom cylinder bottom side. boom flow rate control valve boom flow rate control valve
• Shifts boom flow rate control is not shifted, boom lower is not shifted, boom lower
valve by boom lower pilot speed becomes fast during speed becomes fast during
pressure. combined operation. combined operation.
• If valve is kept open, as • If valve is kept open, as
boom flow rate control valve boom flow rate control valve
is shifted, pressure oil from is shifted, pressure oil from
pump 1 does not flow to pump 1 does not flow to
boom 1 spool. Therefore, boom 1 spool. Therefore,
machine cannot be raised off machine cannot be raised off
ground with front attachment. ground with front attachment.
Auxiliary Flow Combining • Be shifted by pilot pressure • If switch valve is kept closed, • If switch valve is kept closed,
Valve (Optional) from auxiliary flow combining attachment speed does not attachment speed does not
solenoid valve when become fast during single become fast during single
attachment mode (secondary auxiliary operation. auxiliary operation.
crusher, primary crusher) of • If switch valve is kept open, • If switch valve is kept open,
travel speed “ON” is attachment speed does not attachment speed does not
selected. become slow when become slow when
• Supplies pressure oil from attachment mode (HSB attachment mode (HSB
pump 1 to auxiliary spool. breaker, NPK breaker) of breaker, NPK breaker) of
travel speed “OFF” is travel speed “OFF” is
selected. selected.
Selector Valve (Optional) • Be shifted by pilot pressure • If spool is bound or spring is • Breaker stroke becomes few.
from selector valve control broken, pressure oil from
solenoid valve. breaker does not return to
hydraulic oil tank.
Accumulator Control • Be shifted by pilot pressure • If spool is bound or spring is • When NPK breaker is used,
Valve (Optional) from accumulator control broken, accumulator shifting hydraulic pulsation (hose
solenoid valve. is turned OFF. vibration) becomes big.
Secondary Pilot Relief • Be shifted by pilot pressure • If spool is bound or spring is • Relief set-pressure in
Pressure Control Valve from secondary pilot relief broken, relief circuit in auxiliary circuit does not
pressure control solenoid breaker is blocked. decrease.
(Optional) valve.
T5-7-40
Section in T/M)
T3-3
- - - -
T3-3
- - - -
T2-2
- - - -
T2-2
- - - -
T2-2
- - - -
T5-7-41
CORRELATION BETWEEN TROUBLE
SYMPTOMS AND PART FAILURES
This table indicates the relationship between machine z : Related, required to check
{ : Related. However, in case this component fails, other trouble
troubles and parts contributing to the cause of the symptom will be more noticeable so that this component will
trouble if failed. not be the direct cause of the trouble concerned.
Engine System Troubleshooting

E-1 E-2 E-3
Starter does not rotate. Even if starter rotates, engine When engine control dial is
Trouble does not start. fully rotated, engine stalls.
Symptom When engine control dial is
fully rotated, engine speed is
slow.
Parts
MC z z
ECM {
ICF {
Monitor Unit z {
Pump 1 Delivery Pressure Sensor
Pump 1 Control Pressure Sensor
Pressure Sensor (Travel)
Pressure Sensor (Front Attachment)
Pressure Sensor (Boom Raise)
Pressure Sensor (Arm Roll-In)
Pressure Sensor (Auxiliary)
Hyd. Oil Temperature Sensor
Key Switch z
Engine Control Dial
Auto-Idle Switch
Power Mode Switch
Travel Mode Switch
Starter Cut Relay z
ECM Main Relay
Battery Relay z
Glow Relay
Engine Electrical Equipment
Engine Unit z z
Pump Regulator
Swing Parking Brake Release Spool
(Signal Control Valve)
Check batteries.
Remarks
T5-7-42
NOTE: The trouble symptoms in this table are de- In case more than one trouble occurs at
scribed provided that each trouble occurs the same time, find out all faulty compo-
independently. nents while checking all suspected com-
ponents in each trouble symptom.
E-4 E-5 E-6 E-7

Even if engine control dial is Engine speed does not increase Faulty HP mode. Faulty Travel HP mode.
rotated, engine speed remains when engine starts.
unchanged.
z z z z
z z { {
z z
z z
z
z
z
z
z
z
T5-7-43
z : Related, required to check
symptom will be more noticeable so that this component will
not be the direct cause of the trouble concerned.
E-8 E-9 E-10

Even if key switch is turned Faulty auto-idle system. Faulty E mode.
Trouble OFF, engine does not stop.
Symptom
Parts
MC { z z
ECM z { {
ICF
Monitor Unit
Pump 1 Delivery Pressure
Sensor z
Sensor z
Pump 1 Control Pressure
Sensor z
Sensor z
Pressure Sensor (Travel) {
Pressure Sensor (Front At-
tachment) {
Key Switch {
Engine Control Dial
Auto-Idle Switch z
Power Mode Switch z
Travel Mode Switch
Starter Cut Relay
ECM Main Relay
Battery Relay
Glow Relay
Engine Electrical Equipment
Engine Unit
Pump Regulator
Swing Parking Brake Release
z
Spool (Signal Control Valve)
Remarks
T5-7-44
E-11 E-12 E-13

When traveling or operating Engine speed does not increase When attachment mode is se-
front attachment with engine even if attachment is operated lected, engine speed does not
running at slow idle, engine in attachment mode. decrease.
hunts.
z z z
{ { {
{ {
T5-7-45
E-14 E-15
Engine stalls during operation Engine is difficult to start at low
Trouble under adverse condition such temperature.
Symptom as at high altitude.
Parts
MC z
ECM z z
ICF
Monitor Unit
Sensor
Sensor
Sensor
Sensor
Pressure Sensor (Front
Attachment)
Coolant Temperature Sensor z
Key Switch
Engine Control Dial
Auto-Idle Switch
Power Mode Switch
Travel Mode Switch
Torque Control Solenoid Valve z
Starter Cut Relay
ECM Main Relay
Battery Relay
Glow Relay z
Engine Electrical Equipment { z
Engine Unit { z
Pump Regulator z
Swing Parking Brake Release
Check batteries.
Remarks
T5-7-46
(Blank)
T5-7-47
All Actuator System Troubleshooting

A-1 A-2 A-3
All actuator speeds are slow. All actuators are not operated. Left travel is not operated during
Trouble single travel operation. Single
Symptom swing operation speed becomes
slow. Arm speed is slightly slow
during arm level crowding.
Parts
MC z
ECM {
Monitor Unit {
Pilot Shut-Off Solenoid Valve z
Sensor
Pilot Shut-Off Lever z
Pilot Shut-Off Relay z
Security Relay z
Spool
Main Relief Valve {
Arm 1 Flow Rate Control
Valve
Main Pump z z
Regulator { z
Pilot Pump z
Pilot Valve
Pilot Relief Valve z
Pump 1 Flow Rate Control
Valve (Signal Control Valve)
z
Arm Flow Rate Control Valve
Control Spool (Signal Control
Valve)
Remarks
NOTE: The trouble symptoms in this table are de- z : Related, required to check
scribed provided that each trouble occurs { : Related. However, in case this component fails, other trouble
independently. In case more than one trou- not be the direct cause of the trouble concerned.
ble occurs at the same time, find out all
faulty components while checking all sus-
pected components in each trouble symp-
tom.
T5-7-48
A-4 A-5 A-6 A-7

Right travel is not operated dur- Actuator does not stop even if Occasionally, swing or arm Actuator speed is faster than
ing single travel operation. Sin- control lever is turned to neutral. roll-in speed becomes slow normal.
gle bucket operation speed be- during combined operation of Machine mistracks when travel
comes slow. Boom is not raised swing and arm roll-in. lever is operated at half stroke.
properly during arm level Precise control cannot be per-
crowding. formed.
z
z
z z
z z
T5-7-49
A-8
Engine lug down is large when
Trouble actuator in maximum flow rate
Symptom gear pump (optional) is oper-
ated.
Parts
MC z
ECM
Monitor Unit
Pilot Shut-Off Solenoid Valve
Sensor
Pilot Shut-Off Lever
Pilot Shut-Off Relay
Security Relay
Spool
Main Relief Valve
Arm 1 Flow Rate Control
Valve
Main Pump
Regulator
Pilot Pump
Pilot Valve
Pilot Relief Valve
Arm Flow Rate Control Valve
Control Spool (Signal Control
Valve)
z
Sensor (Optional)
Remarks
T5-7-50
(Blank)
T5-7-51
Front Attachment System Troubleshooting

F-1 F-2 F-3
All front attachment actuator Even if power digging switch Some cylinder are not oper-
Trouble power is weak. is pushed, power does not ated or speeds are slow.
Symptom increase. Boom raise power is
weak when digging.
Parts
MC z
Solenoid Valve Unit (SG) z
Power Digging Switch z
Spool z
Main Relief Valve z z
Overload Relief Valve z z
Load Check Valve
Digging Regenerative Valve
Boom Regenerative Valve
Arm Regenerative Valve
Bucket Regenerative Valve
Boom Flow Rate Control Valve
Arm 1 Flow Rate Control Valve
Bucket Flow Rate Control Valve
Boom Lower Meter-In Cut Valve
Boom Anti-Drift Valve
Arm Anti-Drift Valve
Emergency Valve
Shockless Valve (Signal Control Valve) z
Shuttle Valve (Signal Control Valve) z
Bucket Flow Rate Control Valve Con-
trol Spool (Signal Control Valve)
Arm Flow Rate Control Valve Control
Pilot Valve z
Cylinder
Remarks
T5-7-52
F-4 F-5 F-6 F-7 F-8
Arm speed is slow during Arm roll-in speed is slow Bucket is slightly slow When starting to move When starting to move
combined operation. when digging. during bucket roll-in sin- during combined opera- during combined opera-
During combined opera- gle operation. Bucket tion, arm does not tion, boom does not
tion of boom raise and does not move smoothly smoothly move. Arm smoothly move. Boom
arm roll-in, boom raise during bucket roll-in sin- starts to move slightly starts to move slightly
speed is slow. Arm gle operation. slow during arm roll-in slow during boom lower
speed is slow during arm single operation. These single operation.
level crowding. troubles often occur
when temperature is low.
z z
z
z
{ {
{ {
{
{ {
{ {
z
z
z z
z
z
z z
z
{
z

T5-7-53
Front Attachment System Troubleshooting
F-9 F-10 F-11 F-12
When boom raise Front attachment Boom lower above Machine cannot
Trouble or arm roll-out is drifts remarkably. ground is faster be raised off
Symptom operated, boom or than other actua- ground.
arm starts to tors during com-
move after slightly bined operation.
moving downward.
MC
Solenoid Valve Unit (SG)
Power Digging Switch
Spool z
Main Relief Valve
Overload Relief Valve z
Load Check Valve z
Digging Regenerative Valve
Boom Regenerative Valve
Arm Regenerative Valve
Bucket Regenerative Valve
Boom Flow Rate Control Valve z z
Bucket Flow Rate Control Valve
Boom Lower Meter-In Cut Valve z z
Boom Anti-Drift Valve z z
Arm Anti-Drift Valve z z
Emergency Valve {
Shockless Valve (Signal Control Valve)
Shuttle Valve (Signal Control Valve)
Bucket Flow Rate Control Valve Control Spool
Arm Flow Rate Control Valve Control Spool
z
Pilot Valve
Cylinder z
Remarks

T5-7-54
F-13 F-14 F-15

Attachment speed Attachment speed Attachment speed
Trouble is fast during is fast during is fast during
Symptom combined opera- combined opera- combined opera-
tion of attachment tion of attachment tion of attachment
(optional) and (optional) and (optional) and
front attachment front attachment front attachment
(when secondary (when breaker (when vibrating
crusher or primary attached with aux- hammer is used).
Parts crusher is used). iliary flow combin-
ing line is used).
MC z z z
Auxiliary Flow Rate Control Solenoid Valve z
Auxiliary Flow Combining Solenoid Valve z
Maximum Pump 1 Flow Rate Limit Control
z
Solenoid Valve
Pressure Sensor (Auxiliary) z z z

Pressure Sensor (Travel) z
Pressure Sensor (Arm Roll-Out) z z
Auxiliary Flow Rate Control z
Auxiliary Flow Combining Valve z
Remarks
T5-7-55
Swing/Travel/Other System Troubleshooting

S-1 S-2 T-1 T-2
Swing is slow or un- Swing is slow (weak Both right and left One side track does
Trouble moving. in power) during tracks do not rotate or not rotate or rotates
Symptom combined operation rotate slowly. slowly. Machine mis-
of swing and arm tracks.
roll-in. Swing does
not start smoothly.
Swing power is weak.
Parts
MC (Main Controller) z
Solenoid Valve Unit (SI)
Pump 2 Delivery Pressure Sensor {
Pressure Sensor (Swing) {
Pressure Sensor (Arm Roll-In) {
Travel Mode Switch
Pump Device
Spool z
Load Check Valve
Arm 1 Flow Rate Control Valve z
Flow Combiner Valve
Swing Parking Brake Release Spool
z
Pump 1 Flow Rate Control Valve
{
Pump 2 Flow Rate Control Valve
z {
Flow Combiner Valve Control Spool
Arm Flow Rate Control Valve Control
z
Shuttle Valve (Signal Control Valve) { {
Swing Device z
Travel Device z
Center Joint z
Pilot Valve z z
Refer to T-5. In case either bucket
or swing is also slow,
Remarks refer to A-3 or A-4.
T5-7-56
T-3 T-4 T-5 O-1 O-2
Machine mistracks during Occasionally, machine Fast travel is not se- Wiper is not operated. Air Conditioner is faulty.
combined operation of may mistrack when trav- lected. Travel mode does
travel and front attach- eling with engine running not change from slow
ment. at slow speed. mode to fast mode.
z
z
z
{ {
{ {
{
{
{ {
z
z
Operate the wire switch.

T5-7-57
ENGINE SYSTEM TROUBLESHOOTING
E-1 Starter does not rotate.
Related MC Fault Code: None
IMPORTANT: As electric current from the key

switch is not routed to starter
relay 2 with the pilot shut-off
lever in ON position, the starter
does not rotate. (Refer to “Elec-
trical System”.)
• This trouble has nothing to do with the electronic

control system such as MC. YES Faulty starter cut relay.
Switch starter cut relay Disconnect starter cut

YES with other general re- relay.
lay. Check if voltage at
Check if starter rotates. terminals #1 and #3
of harness end of
· Key switch: START NO connector is 24 V.
Check if voltages at · Monitor unit: Primary
YES terminals #5 and #6 in screen · Key switch: START
key switch are 24 V. · Monitor unit: Primary
screen
· Key switch: START
· Monitor unit: Primary Check for continuity YES Faulty key switch.
screen between positive ter-
Check if primary minal in battery and
screen or password NO terminal #1 in key Faulty harness between
input screen is dis- switch. NO battery and key switch.
played on monitor unit.
· Key switch: ON Disconnect connector
YES Faulty monitor unit.
monitor-A in monitor
NOTE: As for the YES unit.
password Check if battery volt- Check if voltage be- Open circuit in harness
setup type age and electrolyte tween terminal #A7 of between monitor unit
NO
machine, the NO density are normal, harness end of con- and key switch.
and fusible link (45 A) nector and machine is
password is not blown. 24 V or more.
input screen
· Voltage: 24 V or more · Key switch: ON
is displayed. Faulty battery.
Density: 1.26 or more
NO Faulty fusible link.
Key Switch: Battery Relay:

Terminal A
T178-05-04-001
T105-07-04-002
T5-7-58
Faulty starter, or faulty

YES harness between starter
and battery relay.
YES Check if voltage at
terminal A in battery
relay is 24 V.
Check if voltage at Faulty battery relay.
YES terminal #2 of har- NO
ness end of con-
Disconnect connector nector in starter cut
of starter relay 2. relay is 0 V.
Connect terminal S of Shorted circuit in harness
harness end of con- between starter cut relay
YES nector to machine. NO and emergency stop
Check for continuity switch.
between terminal #4 of
harness end of con-
nector in starter cut
relay and machine. Open circuit in harness
between starter cut relay
NO and starter relay 2.

between key switch and
NO starter cut relay.

open side)
Monitor Unit Starter Cut Relay

Connector Monitor-A
#A7
T183-05-05-001 T183-05-04-003
T5-7-59
E-2 Even if starter rotates, engine does not start.
YES Faulty ECM main relay.
Connect terminal #1
of harness end of
connector in ECM
Switch ECM main main relay to ma-
relay with other gen- Connect terminal #5 of YES
chine.
eral relay. harness end of connec- Check for continuity
Check if engine tor in ECM main relay to between terminals
starts. machine. #21, #40 of harness
YES Disconnect connector in end of connector in
ECM. ECM and machine.
Disconnect ECM main Check for continuity
relay from connector. between terminals #2,
Check if voltage be- #5 of harness end of Open circuit in harness
connector and machine. between ECM main relay
NO tween terminal #3 of NO and ECM.
harness end of con-
nector and machine is
specification. Open circuit in harness
· Specification: 24V between key switch and
NO
ECM main relay.
· Check if fuse #8 is
blown.

open side)
ECM Main Relay ECM Connector #21 #24 #5
T183-05-04-003
T1GR-05-04-002
#40 #2
T5-7-60
Disconnect con- YES Open circuit in harness

nector ICF-C in between key switch and
ICF. Check if monitor unit.
YES voltage between
terminal #C7 of Check if fuse #18 is blown.
Disconnect
harness end of
connector MC-B
connector and Open circuit in harness
in MC.
machine is speci- between key switch and
YES Check if voltage
fication. NO ICF.
between terminal
#B16 of harness · Key switch: ON Check if fuse #18 is blown.
end of connector · Specification: 24
and machine is V
Check if voltage Open circuit in harness
YES between terminal specification.
between key switch and
#24 of harness · Key switch: ON NO
MC.
Check for conti- end of connector · Specification: 24
nuity between in ECM and ma- V Check if fuse #18 is blown.
YES terminal #2 of chine is specifica-
harness end of tion.
connector in ECM Open circuit in harness
· Key switch: ON
main relay and between key switch and
· Specification: 24 NO
machine. ECM.
V
Check if fuse #18 is blown.
Faulty ground in ECM

NO main relay.

between ECM main relay
NO and ECM.
Connector MC-B Connector ICF-C

#B16
B1 B8
T1V1-05-04-002
#C7
B19 B25
T5-7-61
E-3 When engine control dial is fully rotated, en-
gine stalls.
When engine control dial is fully rotated, en-
gine speed is slow.
Related MC Fault Code: 11003-3, 11004-2
YES Faulty MC, or faulty CAN

between MC and ECM.
Check if fault code is
displayed.
Fault code Refer to Engine Trouble-

· 11003-3: Abnormal NO shooting Manual.
sensor voltage
· 11004-2: CAN
communication error
· MC or ECM cannot
be selected on con-
troller diagnosing by
using Dr. ZX.
T5-7-62
E-4 Even if engine control dial is rotated, engine
speed remains unchanged.
Related MC Fault Code: 11004-2, 11101-3, 11101-4
Faulty engine control dial,

YES or open circuit in harness
between engine control
dial and MC.
Check if fault code 11101-3 or
11101-4 is displayed. Monitor
engine control standard volt-
age (dial angle) by using Dr.
YES Faulty CAN between MC
ZX.
and ECM.
Check if voltage is normal.
· Standard voltage Check if fault code 11004-2 is
Slow idle position: 0.3 to 1 V NO displayed at the same time.
Fast idle position: 4.0 to 4.7 V
· Possible to display by service · Possible to display on MC
menu and monitoring in monitor by using Dr. ZX.
Faulty MC.
monitor unit. NO
T5-7-63
E-5 Engine speed does not increase when en-
gine starts.
Related MC Fault Code: 11004-2, 11901-3, 11901-4
• Refer to the pages for the Auto Warming Up Con-

trol in the SYSTEM / Control System group in the
T/M (Operational Principle).
0 °C or higher
when starting Normal.
NO Monitor oil temperature.

Faulty key switch, or
YES open circuit in harness
· Monitor item: Hydraulic between key switch and
Monitor key switch. MC.
oil temperature Check if displayed “ky”
· Possible to display by is highlighted in re-
Check if fault code service menu and moni- 0 °C or lower sponse to key switch
11901-3 or 11901-4 toring in monitor unit when starting operation.
is displayed. To A
NO
· Monitor item: Key switch
Faulty hyd. oil tempera-

ture sensor, or open cir-
YES cuit in harness between
hyd. oil temperature
sensor and MC.
NO Faulty MC.
Check if fault code

A 11004-2 is dis-
played at the same
time.
Refer to fault code 11004

YES in Troubleshooting A.
T5-7-64
(Blank)
T5-7-65
E-6 Faulty HP mode
• Even if power mode switch is turned to the HP

mode position, HP mode is not operated. (General
mode normally operates.)
Related MC Fault Codes: 11004-2, 11200-3,

11200-4, 11202-3, 11202-4, 11302-3, 11302-4,
11303-3, 11303-4
• The sensors detect the conditions necessary to • Refer to the pages for HP Mode Control in the
operate HP mode. Therefore, if any of these sen- SYSTEM / Control System group in the T/M (Op-
sors fails, HP mode becomes ineffective. erational Principle).
• Pressure sensors (arm roll-in and boom raise) • Check the wiring connections first.
and pump 1 and 2 delivery pressure sensors are
also engaged in the HP mode control. However, if
these sensors fail, other operating functions will
be also affected.
Faulty power mode

NO switch or open circuit in
mode switch and MC.
Monitor power mode

switch.
NO Check if indication HP
is highlighted when
power mode switch is
turned to “HP mode”.
Faulty MC.
· Monitor item: E/P/HP YES
mode switch
displayed. Faulty corresponding
NO sensor, or open circuit in
sensor.
Check if fault code · Fault code:

11004-2 is displayed at 11200-3 11200-4: Pump 1 delivery pressure sensor
YES the same time. 11202-3, 11202-4: Pump 2 delivery pressure sensor
11302-3, 11302-4: Pilot pressure sensor (boom raise)
11303-3, 11303-4: Pilot pressure sensor (arm roll-in)
T5-7-66
• Even if the power mode switch is not turned to HP
mode, HP mode is operated.
• Boom raise and arm roll-in must be operated

when the average delivery pressures of pump 1
and 2 are high, if HP mode control is performed.
The sensors related to this condition may not be
faulty at the same time.

YES between MC and power
mode switch.
Monitor power mode

switch.
Check if “HP” is dis- YES Faulty ECM.
played.
· Monitor item: E/P/HP
mode switch Check if fault code
· Power mode switch: NO 11004-2 is displayed.
P mode
Faulty MC.
NO
T5-7-67
E-7 Faulty Travel HP mode
• Even if the travel mode switch is turned to FAST

during single travel operation, travel HP mode is not
operated.
Related MC Fault Code: 11004-2, 11200-3, 11200-4,

11202-3, 11202-4, 11304-3, 11304-4
• The sensors detect the conditions necessary to • Refer to the pages for Travel HP Mode Control in
operate travel HP mode. Therefore, if any of the SYSTEM / Control System group in the T/M
these sensors fails, travel HP mode becomes in- (Operational Principle).
effective. • Check the wiring connections first.
• Pressure sensor (travel) and pump 1 and 2 deliv-
ery pressure sensors are also engaged in the HP
mode control. However, if these sensors fails,
other operating functions will be also affected.
Faulty travel mode

NO switch, or open circuit in
harness between travel
mode switch and MC.
Monitor travel mode

switch.
NO When travel mode
switch is shifted, check
if display is changed.
Faulty MC.
· Monitor item: Travel
fast speed YES

displayed.
Faulty corresponding
sensor.
Check if fault code · Fault code:

11004-2 is displayed at 11200-3 11200-4: Pump 1 delivery pressure sensor
YES the same time. 11202-3, 11202-4: Pump 2 delivery pressure sensor
11304-3, 11304-4: Pilot pressure sensor (travel)

T5-7-68
• Even if the travel mode switch is not turned to FAST,
travel mode becomes fast idle.
• Travel must be operated when the average deliv-
ery pressures of pump 1 and 2 are high, if travel
HP mode control is performed. The sensors re-
lated to this condition may not be faulty at the
same time.

YES between MC and travel
mode switch.
Monitor travel mode

switch.
Check if FAST is YES Faulty ECM.
displayed.
mode switch Check if fault code
· Travel mode switch: NO 11004-2 is displayed.
Slow speed
Faulty MC.
NO
T5-7-69
E-8 Even if key switch is turned OFF, engine
does not stop. (In case engine does not stop,
stop engine by turning the emergency stop
switch ON located under the seat stand.
Then, begin inspection.)
Related MC Fault Codes:
• Probably the symptoms such as “Engine speed is

slower than specification in all operating ranges”
or “Even if engine control dial is rotated, engine
speed remains unchanged” may come up. Per-
form troubleshooting for these symptoms.
YES Faulty key switch.
Check if voltage at
terminal #5 in key
switch is 24 V.
NO Shorted circuit in
· Key switch: OFF Disconnect connector harness between key
in ECM. switch and ECM.
Check if voltage be-
tween terminal #24 of
NO harness end of con-
nector and machine is
0 V.
Faulty ECM.
· Key switch: OFF YES
Key Switch
#24
ECM Connector
(Harness end)
T1GR-05-04-002
T105-07-04-002
T5-7-70
(Blank)
T5-7-71
E-9 Faulty auto-idle system
• Even if control lever is turned to neutral, auto-idle

system is not operated.

11307-3, 11307-4
Related ECM Fault Code: 639-2, 639-3
• In case trouble symptoms E1 to E8 are recog- • Refer to the pages for Auto-Idle Control in the
nized, perform the troubleshooting of these trou- SYSTEM / Control System group in the T/M (Op-
bles first. erational Principle).
• Even if failure in pressure sensors (travel and • Check the wiring connections first.
front attachment) may have relevance to malfunc-
tion of the auto-idle control. However, if these
sensors fail, other operating functions will also be
affected.
Check if fault code

YES
11004-2 is dis-
played.
Check if fault code
YES for MC or ECM is
displayed.
Monitor auto-idle
switch. Faulty MC.
YES Check if ON/OFF is NO
shifted when
auto-idle switch is
Check if auto-idle is shifted. Open circuit in har-
displayed on monitor ness between
unit. NO auto-idle switch and
MC.
· Auto-idle switch: ON
Disconnect connec-
tor monitor-B in YES Faulty auto-idle
monitor unit. switch.
between terminal
NO #B18 of harness end Open circuit in har-
of connector and ness between
machine. NO auto-idle switch
· Auto-idle switch: ON monitor unit.

open side)
Connector Monitor-B
10 9 8 7 6 5 4 3 2 1
20 19 18 17 16 15 14 13 12 11
#B18
T5-7-72
Refer to fault code

YES
11004 in Trouble-
shooting A.
Refer to Engine
YES
Troubleshooting
Manual.
Check if fault code
639-2 or 639-3 is
NO displayed. Faulty corresponding
sensor, or open cir-
NO cuit in harness be-
tween MC and sen-
sor.
· Fault code:
11304-3, 11304-4: Pilot pressure sensor (travel)
11307-3, 11307-4: Pilot pressure sensor (front attachment)
T5-7-73
Even if auto-idle switch is turned OFF, auto-idle is op-
erated.
Shorted circuit in
YES harness between MC
MC-B in MC and con- and auto-idle switch.
nector in switch panel.
between terminal #B6 Refer to fault code
of harness end of YES
11004 in Trouble-
connector MC-B and shooting A.
machine. Check if fault code
NO 11004-2 is displayed.
· Auto-idle switch: OFF
Faulty MC.
NO

open side)
Connector MC-B
#B6
B1 B8
B19 B25
T5-7-74
(Blank)
T5-7-75
E-10 Faulty E mode
• Even if power mode switch is turned to the E mode

position, engine speed remains unchanged. (Engine
speed does not decrease.)

11202-3, 11202-4, 11206-3, 11206-4, 11208-3,
11208-4
• In case trouble symptoms E-1 to E-9 are recog- • Pump 1, 2 control pressure sensors and pump 1,
nized, perform the troubleshooting of these trou- 2 delivery pressure sensors are also engaged in
bles first. the E mode control. However, if these sensors fail,
• The sensors detect the conditions necessary to other operating functions will be also affected.
operate E mode. Therefore, if any of these sen- • Refer to the pages for E Mode Control in the
sors fails, E mode becomes ineffective. SYSTEM / Control System group in the T/M (Op-
erational Principle).
Faulty power mode

NO switch, or open circuit in
mode switch and MC.
Monitor power mode

switch.
When power mode
NO
switch is shifted to E
mode, check if display
is changed.
Faulty MC.
· Monitor item: E/P/HP
mode switch YES

displayed.
sensor.
· Fault code:
Check if fault code 11206-3 11206-4: Pump 1 control pressure sensor
11004-2 is displayed. 11208-3, 11208-4: Pump 2 control pressure sensor
YES
11200-3 11200-4: Pump 1 delivery pressure sensor
11202-3, 11202-4: Pump 2 delivery pressure sensor

T5-7-76
• Even if power mode switch is not turned to E mode,
engine speed decreases.
• Required engine speed from the engine control

-1
dial must be beyond 1800 min when the pump
control pressures of pump 1 and 2 are low or the
average delivery pressures of pump 1 and 2 are
high, if E mode control is performed. The sensors
related to this condition may not be faulty at the
same time.

NO between MC and power mode
switch, or faulty power mode
switch.
Monitor power mode switch.
Check if “E” is displayed. YES Refer to fault code 11004 in
Troubleshooting A
· Monitor item: E/P/HP mode
switch Check if fault code
· Power mode switch: P mode YES 11004-2 is displayed.
Faulty MC.
NO
T5-7-77
E-11 When traveling or operating front attach-
ment with engine running at slow idle, en-
gine hunts.

11307-3, 11307-4
• Even if the failure in pressure sensors (travel and

front attachment) may have relevance to malfunc-
tion of idle speed-up control. However, if these
sensors fail, other operating functions will also be
affected. (Refer to the relationship between ma-
chine trouble symptoms and related parts on
page T5-5-2.)
• Refer to the pages for Idle Speed-Up Control in
the SYSTEM / Control System group in the T/M
(Operational Principle).
YES Faulty engine unit or

faulty ECM.
· Set idle speed increasing
Set engine control dial to Min. in MC by using Dr. ZX.
Check if engine speed is
faster than increased idle YES Refer to fault code 11004
speed. in Troubleshooting A.
· Monitor item:
Check if fault code
Engine target speed
· Possible to display by service
menu and monitoring in moni-
tor unit Faulty MC.
NO
· Set idle speed increasing
in MC by using Dr. ZX.
T5-7-78
E-12 Engine speed does not increase even if at-
tachment is operated in attachment mode.
• In case trouble symptoms E-1 to E-11 are recog- • Refer to the pages for Attachment Operation
nized, perform the troubleshooting of these trou- Speed Increase Control in the SYSTEM / Control
bles first. System group in the T/M (Operational Principle).
• Even if the failure in pressure sensor (auxiliary) • Check the wiring connections first.
and power mode switch may have relevance to
the malfunction of attachment operation speed
increase control. However, if these sensor and
switches fail, other operating functions will also be
affected.
NO Normal (Set to “Increase

(+)”.)
Check if attachment
speed adjustment
NO has been set to “In-
crease (+)” on “Pa- YES
rameter Change” in Monitor attachment To A
Dr. ZX. pilot pressure.
Check if pressure
Check if attachment YES varies in response to
speed adjustment lever stroke. Faulty auxiliary pressure
has been set to “De-
· Monitor item: Att. NO sensor.
crease (-)” on “Pa-
rameter Change” in control pilot pressure
Dr. ZX.
Normal (If P speed is set

to decrease”, this control
YES system is deactivated.)
YES Refer ti fault code 11004

in Troubleshooting A.
Fault code 11004-2 or

A 11918-2 is displayed.
Faulty MC.
NO
T5-7-79
E-13 When attachment mode is selected, engine
speed does not decrease.
• In case trouble symptoms E-1 to E-11 are recog-

nized, perform the troubleshooting of these trou-
bles beforehand.
• Refer to the pages for Attachment Operation
Speed Limit Control in the SYSTEM / Control
System group in the T/M (Operational Principle).
YES Refer ti fault code 11004

in Troubleshooting A.
Check if fault code

YES
11004-2 or 11918-2 is
displayed.
Faulty MC.
Check if attachment NO
speed adjustment has
been set to “Decrease
(-)” in on “Parameter
Change” in Dr. ZX.
Normal (Set to “Decrease

NO (-)”.)
T5-7-80
(Blank)
T5-7-81
E-14 Engine stalls during operation under ad- Test Harness (ST 7226)
verse condition such as at high altitude. When operating corresponding control lever and
switch: ON
11401-2, 11401-3, 11401-4
• If speed sensing control is not operated, the en-

4
gine will stall under adverse operating conditions.
3
• Check the wiring connections first. 50
150 50 50
1 2 2 1
T107-07-06-015
YES Faulty torque control

solenoid valve.
Disconnect harness of
Check if fault code torque control sole-
NO
11401-2, 11401-3 or noid valve.
11401-4 is displayed. Monitor torque control NO Connect test harness
solenoid valve output. (ST 7226) between
Install pressure gauge solenoid valve and
to output port so that harness.
pressure is measured Check if test harness
by pressure gauge and lamp comes ON.
Dr. ZX.
NO
Monitor actual engine Check if both meas-
speed. ured pressure values
Check if engine speed by pressure gauge and
is abnormal. Dr. ZX vary identically. Disassemble and
YES check regulator.
· Monitor item: Pump torque
· Monitor item:
proportional solenoid valve
Engine actual speed
output
· Possible to display by
· Refer to the Operational
service menu and
Performance Test section.
monitoring in monitor
unit. Refer to fault code
YES
11004 in Trouble-
shooting A.
Check if fault code
11004-2 or 11100-2 is
YES displayed. YES Refer to Engine Trou-
bleshooting Manual.
Check if fault code
Faulty MC.
NO
T5-7-82
YES Faulty torque control so-

lenoid valve.

between torque control
NO solenoid valve and MC.
T5-7-83
E-15 Engine is difficult to start at low tempera-
ture. (During cold weather or in cold dis-
tricts, engine is difficult to start or does not
start even if pre-heated.)
• Check if electricity is routed to the glow plugs. • Check the battery.

Check the glow plugs for any abnormality. • Check the wiring connections first.
• The pre-heat system operates only when coolant
temperature is below 20 °C (68 °F).
YES Faulty sensor.
Disconnect connector of
coolant temperature sensor.
Check if voltage at glow plug YES Faulty ECM.
is 20 to 24 V.
· Key switch: ON Disconnect connector in
ECM. Connect terminal #4 of
harness end of connector to
NO machine. Check if problem is
corrected.
· Connect to machine from Measure each glow plug
the back of connector by NO resistance.
using a clip with the con-
nector connected. · Key switch: OFF
· Before measuring, re-
move copper plates
connecting each glow
plug.
• Measurement of Glow Plug Voltage and Resistance

Voltage Check
Resistance Check
Remove
the
copper
plate.
Specification: 20 to 24 V
T105-07-04-006
Specification: Below 10 Ω
T105-07-04-007
T5-7-84
∞Ω Faulty glow plug.
NO Faulty glow relay, or

faulty harness between
Connect connector in glow relay and glow plug.
glow relay. Connect ter-
YES minal #4 of harness end
of connector to machine.
Check if voltage at glow
plug is 20 to 24 V.
· Key switch: ON
between glow relay and
YES ECM.
Disconnect connector in
glow relay.
Check if voltages at termi-
Below 10 Ω nals #1 and #3 of harness
end of connector in glow
relay are 20 to 24 V.
· Key switch: ON
If terminal #1 is 0 V, open
circuit in harness be-
tween glow relay and
NO battery. If terminal #3 is 0
V, open circuit in harness
between glow relay and
terminal M in key switch.
blown.
T5-7-85
ALL ACTUATOR SYSTEM TROUBLE-
SHOOTING
A-1 All actuator speeds are slow.

11401-2, 11401-3, 11401-4
• Even if speed is satisfactory, in case power is
• Reduction in pump 1 and 2 flow rate due to some weak, refer to the troubleshooting for faulty main
reasons or faulty pilot system (A-2) may cause relief valve (F-1).
this trouble. • Check the wiring connections first.
• Check fuse of the torque control solenoid valve.
Faulty torque control so-

YES lenoid valve, or open cir-
cuit in harness between
MC and torque control
solenoid valve.
Check if fault code

YES 11401-2, 11401-3 or
11401-4 is displayed.
YES Faulty CAN between MC
and ECM, or faulty MC.
Check if fault code

11004-2, 11100-2 or
Check if primary pilot Faulty pump device.
pressure is normal.
NO
· Fully boom raised or fully
arm rolled-in
· Monitor item: Boom raise
pilot pressure, Arm roll-in
pilot pressure YES Faulty pilot pump, or
clogged pilot filter.
Adjust, disassemble
and clean pilot relief
valve.
NO Check if same symp-
tom appears.
End.
NO
T5-7-86
(Blank)
T5-7-87
A-2 All actuator are not operated.
• The pilot shut-off circuit may be faulty.

• When the key switch is turned to the START posi-
tion with the pilot shut-off lever in the ON position,
the starter does not rotate.
• When the key switch is turned to the START posi-
tion with the emergency switch and the pilot
shut-off lever in the ON position, the starter ro-
tates.
• Refer to the pages for the Electrical System
group / SYSTEM in the T/M (Operational Princi-
ple).
YES Faulty pilot shut-off relay.
Switch pilot shut-off

relay with other gen- YES Faulty security relay.
eral relay.
Check if actuator can
be operated.
Connect terminal #2 of
· Pilot shut-off lever: Switch security relay harness end of con-
ON with other general nector in pilot shut-off
relay. solenoid valve to ma-
NO Check if actuator can chine.
YES
be operated. Disconnect connector
Disconnect connec- in pilot shut-off relay.
· Pilot shut-off lever: tor in pilot shut-off Check for continuity
ON solenoid valve. between terminal #2 of
Check if voltage be- harness end of con-
NO tween terminal #1 of nector and machine.
harness end of con-
nector and machine
is 24 V. Open circuit in harness
between pilot shut-off so-
· Key switch: ON NO lenoid valve and battery
relay.
blown.
Connector (Harness end of connector viewed from the · Check if fusible link
open side) 65A is blown.
Pilot shut-Off Relay Pilot Shut-Off Solenoid Valve

Security Relay
T1V1-05-04-103
#1 #2
T183-05-04-003
T5-7-88

between terminal #2
YES of harness end of
To A
connector in security
Check for continuity relay and machine.
between terminal #3
YES
Connect terminal #5 of of harness end of
harness end of con- connector in security
nector in pilot shut-off relay and machine.
Faulty ground in security
relay to machine.
YES Disconnect security NO relay.
relay.
between terminal #4 of
harness end of con-
nector and machine. Open circuit in harness
Check if voltage between pilot shut-off re-
YES between terminal NO lay and security relay.
#1 of harness end
of connector in pilot
shut-off relay and
machine is 24 V.

between pilot shut-off re-
NO lay and battery relay.

between pilot shut-off so-
NO lenoid valve and pilot
shut-off relay.
T5-7-89
Faulty monitor unit, or

YES shorted circuit in harness
between monitor unit and
security relay.
Connect connector YES Faulty pilot shut-off sole-

monitor-B. noid valve.
YES between terminal #2
of harness end of
A connector in pilot
shut-off relay and Faulty monitor unit.
Check for continuity machine. NO
YES between terminals · Pilot shut-off lever:
#B19 and #B12 of ON
harness end of con-
Connect terminal #2 of nector monitor-B.
harness end of con- Open circuit in harness
nector in pilot shut-off between terminals #B12
relay to machine. and #B19 of harness end
Disconnect connector of connector monitor-B,
monitor-B in monitor NO
or faulty pilot shut-off
NO unit. lever.
between terminal #2
of harness end of
connector and ma-
chine.
between pilot shut-off re-
NO lay and monitor unit.

open side)
Pilot Shut-Off Relay

Connector Monitor-B
#B2
10 9 8 7 6 5 4 3 2 1
20 19 18 17 16 15 14 13 12 11
T183-05-04-003
#B19 #B12
T5-7-90
(Blank)
T5-7-91
A-3 Left travel is not operated during single
travel operation. Single swing operation
speed becomes slow. Arm speed is slightly
slow during arm level crowding. (All prob-
lems occur at the same time.)
• The pump 2 flow rate is minimized (approx. 20

L/min) due to some reasons. Accordingly, the left
travel and swing motors, which are driven by
pressure oil from pump 2, moves very slow.
• Pressure oil from pump 1 is also routed to the
arm and boom cylinders so that the arm and
boom can move at a slightly slow speed in single
operation. However, in level crowd operation,
pressure oil is routed to the boom prior to the arm
so that arm speed becomes very slow.
• Refer to the SYSTEM / Hydraulic System group in
the T/M (Operational Principle).
YES Faulty pump 2 regulator.
Monitor pump 2 pump

control pressure.
Check if pressure in-
creases in proportion to
left travel lever stroke.
Bound pump 2 flow rate
· Monitor item: Pump 2 control valve in signal con-
pump control pressure NO trol valve.
service menu and moni-
toring in monitor unit.
T5-7-92
A-4 Right travel is operated during single travel
operation. Single bucket operation speed
becomes slow. Boom is not raised properly
during arm level crowding. (All problems
occur at the same time.)
• The pump 1 flow rate is minimized (approx. 20

L/min) due to some reasons. Accordingly, the
right travel motor and bucket cylinder, which are
actuated by pressure oil from pump 1, moves
very slow.
• Pressure oil from pump 2 is also routed to the
arm and boom cylinders so that the arm and
boom can move at a slightly slow speed in single
operation. However, in level crowd operation,
pressure oil is routed to the arm prior to the boom
so that boom is scarcely raised.
YES Faulty pump 1 regulator.
Monitor pump 1 pump

control pressure.
Check if pressure in-
creases in proportion to
right travel lever stroke.
Bound pump 1 flow rate con-
· Monitor item: Pump 1 trol valve in signal control
pump control pressure NO valve.
service menu and moni-
toring in monitor unit.
T5-7-93
A-5 Actuator does not stop even if control lever
is turned to neutral.
• Bound spool in the pilot valve or bound main

spool in the control valve is suspected.
YES Faulty pilot valve.
· When control lever is in neu-

tral, pilot pressure is routed to
spool end in control valve.
Check if actuator stops when
pilot shut-off lever is turned to
OFF position.
Faulty control valve.

NO
· Even if pilot pressure is not
routed to spool end in control
valve, spool is kept opened
due to binding of spool.
T5-7-94
A-6 Occasionally, swing or arm roll-in speed
becomes slow during combined operation
of swing and arm roll-in.
• The arm 1 flow rate control valve may be faulty.

• Refer to the pages for the COMPONENT OPERA-
TION / Control valve group in the T/M (Operational
Principle).
Faulty arm 1 flow rate

YES
control valve in control
Install a pressure valve.
gauge to hose SE
connecting from signal
control valve to arm 1
flow rate control valve
in control valve.
When relieving during
combined operation of
swing and arm roll-in,
check if pressure is 3.9 Bound control spool of
2
MPa (40 kgfcm ). arm 1 flow rate control
NO valve in signal control
valve.
Control Valve Signal Control Valve

(Control Valve Side)
Arm 1 Flow Rate

Control Valve
Hose SE
T1V1-05-04-004
T178-03-06-015
T5-7-95
A-7 Actuator speed is faster than normal
Machine mistracks when travel lever is op-
erated at half stroke. Precise control cannot
be performed.
• The pump 1 or 2 flow rate is maximized due to

some reasons.
Therefore, the maximum flow rate is supplied and
actuator speed is faster though the control lever
does not reach the full stroke.
• Pressure oil from pump 1 makes right travel per-
form, and pressure oil from pump 2 makes left
travel during single travel operation. When the
travel lever is operated at half stroke, different
flow rates between pump 1 and 2 occur and the
machine mistracks.
YES Faulty pump regulator.
Monitor pump control pressure

of pump 1 and 2.
Check if pressure changes in
response to lever operation.
Bound pump flow rate control
· Pump 1: Bucket operation valve in signal control valve.
· Pump 2: Swing operation NO
· Monitor item: Pump 1 and 2
pump control pressures
· Possible to display by service
menu and monitoring in monitor
unit.
T5-7-96
(Blank)
T5-7-97
A-8 Engine lug down is large when actuator in
maximum flow rate gear pump (optional) is
operated.
Open circuit in har-

NO ness between MC and
pump 3 delivery
Check for continuity in pressure sensor.
harness between ter-
minal #D3 of harness
YES Check for continuity
end of connector MC-D
in MC and terminal #2 in in harness between
pump 3 delivery pres- MC and torque con-
YES trol solenoid valve.
Disconnect connector in sure sensor.
pump 3 delivery pres- · Between terminal #A30
NO sure sensor. of connector MC-A in
Check if voltage be- MC and terminal #1 of
tween terminals #1 and connector in torque
#3 of harness end of control solenoid valve
Switch pump 3 deliv- connector is 5±0.5 V. · Between terminal #A19
ery pressure sensor of connector MC-A in
with pump 1 or 2 de- · Key switch: ON
livery pressure sen- connector in torque
sor. control solenoid valve
displayed.
YES Open circuit in har-
· Fault code: ness between MC and
11200-3, 11200-4: pump 3 delivery
tween terminals #1 of
Pump 1 delivery pres- pressure sensor (ter-
harness end of connec-
sure sensor minal #3).
tor in pump 3 delivery
11202-3, 11202-4: NO pressure sensor and
Pump 2 delivery pres- Open circuit in har-
machine is between
sure sensor ness between MC and
0.25 and 4.5 V.
pump 3 delivery
· Key switch: ON NO pressure sensor (ter-
minal #1).
Faulty pump 3 deliv-

YES ery pressure sensor.
Connector (Harness end of connector viewed from the open
side)
MC
Connector MC-A Pump 3 Delivery Pressure Sensor
#A19
T1V1-05-07-101
#A30 T183-05-04-008
MC
#D3 Torque Control Solenoid Valve
Connector MC-D
T1V1-05-04-003
T183-05-04-009
T5-7-98
torque control solenoid YES Faulty torque control
valve and maximum solenoid valve.
YES pump 2 flow rate limit
Check if fault code for Faulty MC.
pump 2 flow rate limit
control solenoid valve is NO
displayed.

ness.
NO
T5-7-99
FRONT ATTACHMENT SYSTEM TROU-
BLESHOOTING
F-1 All front attachment actuator power is weak.
• In case operating speeds are extremely slow,

pump control may be malfunctioning (A-3 and/or
A-4). Faulty pilot system may also cause this trou-
ble.
34.3 to 36.3 MPa Main relief valve should be

2
(350 to 370 kgf/cm ) normal.
Find out cause of trouble by
tracing other trouble symptoms.
Monitor pump 1 and 2 deliv-

ery pressures.
· Monitor item: Pump 1 and 2 de-
livery pressure
· Possible to display by service Adjust main relief valve.
menu and monitoring in monitor
unit. Less than 34.3 MPa
2
· Relieve boom, arm and bucket (Less than 350 kgf/cm )
circuits.
· Power mode switch: OFF
· Work mode: Digging
T5-7-100
F-2 Even if power digging switch is pushed,
power does not increase. Boom raise power
is weak when digging.
Related MC fault Code: 11404-2, 11404-3, 11404-4
• Refer to the pages for the SYSTEM / Control

System group / Power Digging Control and
Auto-Power Lift Control in the T/M (Operational
Principle).
YES Faulty solenoid valve unit

(SG), or open circuit in
harness between sole-
Pressure increases. noid valve unit (SG) and
2
Less than 34.3 MPa (350 kgf/cm )
↓ Normal (HP mode may
Check if fault code 2
36.5 MPa (370 kgf/cm ) be confused.)
is displayed.
· Fault code:
11404-2, 11404-3,
11404-4 Monitor pump 1
and 2 delivery YES
NO · pressures. Faulty main relief valve.
Monitor item:
Pump 1 and 2
pressures Monitor power digging
· Possible to display switch.
by service menu Pressure Push power digging
and monitoring in does not switch. Faulty power digging
monitor unit. increase. Check if “Pd” is switch, or open circuit in
· Push power dig- changed. NO harness between power
ging switch and digging switch and MC.
· Monitor item: Power
check pump pres- digging switch
sure change with in · In case boom raise
8 seconds. power is weak during
digging, go to YES.
T5-7-101
F-3 Some cylinders are not operated or speeds
are slow.
• When other actuators (travel and swing) operate

normally, the pilot pump (primary pilot pressure) is
considered to be normal.
• In case single bucket operation speed is slow,
refer to F-6.
• In case single arm roll-in operation speed is slow,
refer to F-7.
• In case single boom lower operation speed is
slow, refer to F-8.
YES Bound control valve
spool, or faulty cylinder
(faulty seal kit).
YES Check if overload

relief pressure is nor-
mal.
Monitor pump control Faulty overload relief

pressure. NO valve.
YES Check if pump con-
trol pressure
changes smoothly
while moving control
lever slowly.
· Monitor item: Faulty shuttle valve in
Pump 1 pump con- NO signal control valve.
Measure or monitor trol pressure, pump
secondary pilot 2 pump control
pressure. pressure
Check if secondary · Possible to display
pilot pressure is by service menu
normal. and monitoring in
monitor unit.
· Secondary pilot
pressure: YES Bound shockless valve
Refer to Operational spool in signal control
Performance Test valve.
section. Check if secondary
· Monitor item: Boom pilot pressure at inlet
raise pilot pressure, NO port to signal control
arm roll-in pilot pres- valve. Faulty pilot valve.
sure. · Check only when NO
· Possible to display by boom is not raised.
service menu and In case cylinders
monitoring in monitor other than boom are
unit. abnormal, skip this
step and go NO.
T5-7-102
(Blank)
T5-7-103
F-4 Arm speed is slow during combined opera-
tion. During combined operation of boom
raise and arm roll-in, boom raise speed is
slow. Arm speed is slow during arm level
crowding.
Related MC Fault Codes: 11200-3, 11200-4, • Refer to the pages for the SYSTEM / Control
11202-3, 11202-4, 11303-3, 11303-4, 11301-3, System group / Arm Regenerative Control in the
11301-4, 11302-3, 11302-4, 11403-2, 11403-3, T/M (Operational Principle).
11403-4
Faulty corresponding sen-
sor, or faulty MC.
YES between MC and sensor.
(SC), or open circuit in
harness between solenoid
valve unit (SC) and MC.
YES Faulty arm 1 flow rate con-

Check if fault code is Check if arm 1 flow trol valve.
displayed.
YES rate control valve at
5-spool side in control
· Fault code valve is scored or Check if arm regenerative
11200-3, 11200-4: Install a pressure gauge
bound. valve at 4-spool side in
Pump 1 delivery pres- to hose SE connecting
sure sensor from signal control valve NO control valve is scored or
bound.
11202-3, 11202-4: to arm flow rate control
Pump 2 delivery pres- valve in control valve.
sure sensor NO When relieving during
11303-3, 11303-4: combined operation of Faulty control spool in
Pressure sensor (arm swing and arm roll-in, arm flow rate control
roll-in) check if pressure is 3.9 NO valve (signal control
2
11301-3, 11301-4: MPa (40 kgfcm ). valve).
Pressure sensor
(swing)
11302-3, 11302-4:
Pressure sensor
(boom raise)
11403-2, 11403-3,
11403-4: Solenoid
valve unit (SC)
Signal Control Valve (Control Valve Side) Control Valve
Hose SE
T1V1-05-04-004
Arm 1 Flow Rate
T178-03-06-015
Control Valve
T5-7-104
Section A-A
B B
Arm Regenerative
Valve
T1V1-03-03-026
T1V1-03-03-002 A
YES Faulty arm regenerative

valve.
YES Faulty arm 2 flow rate

control valve.
Check if arm 2 flow rate

control valve at 4-spool
side in control valve is
NO scored or bound.
Find out cause of trouble
by tracing other trouble
NO symptoms.
Section B-B
Arm 2 Flow Rate

Control Valve
T1V1-05-04-005 (Poppet Valve)
Arm 2 Flow Rate
Control Valve T1V1-05-04-007
(Control Valve)
T5-7-105
F-5 Arm roll-in speed is slow when digging.
Related MC Fault Codes: 11200-3, 11200-4, • Refer to the pages for the SYSTEM / Control
11202-3, 11202-4, 11301-3, 11301-4, 11302-3, System group / Digging Regenerative Control in
11302-4, 11402-2, 11402-3, 11402-4 the T/M (Operational Principle).
sensor, or faulty MC.
between MC and sensor
YES
(SF), or open circuit in
harness between sole-
noid valve unit (SF) and
MC
displayed.
· Fault code YES
11200-3, 11200-4: Faulty digging regenera-
Pump 1 delivery Check if digging re- tive valve.
pressure sensor generative valve at
11202-3, 11202-4: 5-spool side in control
NO valve is scored or
Pump 2 delivery
pressure sensor bound. Find out cause of trouble
11303-3, 11303-4: by tracing other trouble
NO
Pressure sensor (arm symptoms.
roll-in)
11302-3, 11302-4:
Pressure sensor
(boom raise)
11402-2, 11402-3,
11402-4: Solenoid
valve unit (SF)
T5-7-106
F-6 Bucket is slightly slow during bucket roll-in
single operation. Bucket does not move
smoothly during bucket roll-in single opera-
tion.
• Bucket flow rate control valve or bucket regenera-

tive valve may be faulty.
• Refer to the COMPONENT OPERATION / Con-
trol Valve group in the T/M (Operational Princi-
ple).
YES Faulty bucket regenera-

tive valve. (Disassemble
and clean or replace.)
Check if bucket re-
YES generative valve in
Install a pressure
bucket spool is
gauge to hose SK
bound or scored. Find out cause of trouble
connecting signal con-
trol valve to bucket by tracing other trouble
flow rate control valve NO symptoms.
NO in control valve.
When relieving during
3-combined operation
of boom raise, arm
roll-in and bucket Bound bucket flow rate
Check if bucket flow roll-in, check if pres- control valve control
rate control valve in sure is 3.9 MPa (40 spool in signal control
2 NO
control valve is k f ) valve.
bound or scored.
Faulty bucket flow rate

control valve. (Disassem-
YES ble and clean or replace.)
Signal Control Valve (Control Valve Side)
Bucket Flow Rate

Control Valve
Hose SK
T1V1-05-04-005
T178-03-06-015
T5-7-107
F-7 When starting to move during combined
operation, arm does not smoothly move.
Arm starts to move slightly slow during arm
roll-in single operation. These troubles often
occur when temperature is low.

ple).
YES Faulty arm regenerative

valve. (Disassemble and
clean or replace.)
NO Check if arm regenera-
tive valve is bound or
scored.
Check if arm anti-drift valve is NO symptoms.
bound or scored.
Faulty arm anti-drift valve.

(Disassemble and clean
YES or replace.)
F-8 When starting to move during combined

operation, boom does not move smoothly.
Boom starts to move slightly slow during
boom lower single operation.

ple).
Faulty boom lower me-
NO ter-in cut valve. (Disas-
semble, clean or re-
place.)
Check if boom lower
NO
meter-in cut valve is Find out cause of trouble
NO
bound or scored. by tracing other trouble
Check if boom re- symptoms.
Check if boom generative valve is
YES bound or scored.
anti-drift valve is
Faulty boom regenerative
bound or scored.
valve. (Disassemble and
YES clean or replace.)
Faulty boom anti-drift

YES valve. (Disassemble and
clean or replace.)
T5-7-108
F-9 When boom raise or arm roll-out is operated,
boom or arm starts to move after moving
slightly downward.
Related MC Fault Code: None YES Faulty anti-drift valve.
YES Check if anti-drift valves

(arm and boom) are
bound or scored.
Oil leaks in cylinder.

NO
Check if load check valve in
control valve is normal.
· Disassemble / Visual
Inspection
Faulty load check valve.

NO
NOTE: 1. During the initial stage of operation, oil

pressure and flow rate from the pump is
low. Therefore, if the load check valve is
malfunctioning, the oil in the bottom side (B)
of the boom cylinder flows back into the When the Load
circuit through the load check valve so Check Valve is
that the boom cylinder temporarily is re- Faulty:
(A)
tracted.
2. As oil pressure and flow rate from the
pump is low, if oil leaks from bottom
side (A) to rod side (B) due to faulty
boom cylinder piston or cylinder barrel,
the boom cylinder is temporarily re-
tracted during the initial stage of opera-
tion. In addition, cylinder force is re-
duced. The cylinder drift increases in T105-07-04-012
this case.
T5-7-109
F-10 Front attachment drifts remarkably.
YES Normal
Correctly adjust emer-

Check if each front NO
gency valve and lock it
attachment cylin- Check if emergency up.
der drift is within valve at boom 1 sec-
specification. NO tion in control valve Check if symptom is
4-spool side is cor- deleted when overload
rectly adjusted. relief valve is tempo-
Check if cylinder drift YES rarily switched with
is reduced when pilot another overload relief
NO shut-off valve is valve.
closed.
Faulty pilot valve.

YES
• Boom Cylinder Internal Leakage Check
1. With the bucket cylinder fully retracted and the

arm cylinder slightly extended from the fully re-
tracted position, lower the bucket tooth tips onto
the ground.
2. Remove the hoses from the boom cylinder rod

side. Drain oil from the hoses and cylinders. (Plug
the disconnected hose ends.)
T105-07-04-009
3. Retract the arm cylinder and lift the bucket off the
ground. If oil flows out of the hose removed pipe
ends and the boom cylinders are retracted at this
time, oil leaks in the boom cylinders. In case no
oil flows out of the hose removed pipe ends but
the boom cylinders are retracted, oil leaks in the
control valve.
T5-7-110
Emergency
Valve
NO Scored control valve

spool, broken spring, or
loose spool end.
NO Check if oil leaks

in cylinders.
Faulty cylinder. (Replace

seal kit.)
YES
T1V1-05-04-005
Faulty overload relief

YES valve.
Emergency
Valve
T178-05-04-003
Adjustment Procedure:
Tighten (1) and tighten (2).
Tightening Torque:
(1)- 13 N⋅m (1.3 kgf⋅m)
(2)- 7 N⋅m (0.7 kgf⋅m)
T5-7-111
F-11 Boom lower above ground is faster than
other actuators during combined operation.
• Boom lower meter-in cut valve or boom flow rate

control valve may be faulty.
• Refer to the pages for the SYSTEM / Hydraulic
System group and the COMPONENT OPERA-
TION / Control Valve group in the T/M (Opera-
tional Principle).
• In case boom lower single operation is slow, refer
to F-8.
YES Faulty boom lower

meter-in cut valve.
Check if boom lower

meter-in cut valve is YES
bound or scored. Faulty boom flow rate
control valve.
Check if boom flow
rate control valve is
NO bound or scored.
NO symptoms.
Boom Lower Meter-In

Cut Valve
Boom Flow Rate

T1V1-03-03-026
T5-7-112
F-12 Machine cannot be raised off ground.
• Boom lower meter-in cut valve or boom flow rate

control valve may be faulty.
System group and the COMPONENT OPERA-
TION / Control Valve group in the T/M (Opera-
tional Principle).
• In case boom lower single operation is slow, refer
to F-8.
YES Faulty boom lower me-

ter-in cut valve.
YES Faulty boom flow rate

control valve.
Check if boom lower
meter-in cut valve is YES Check if boom flow
bound or scored. rate control valve is
bound or scored.
NO symptoms.
Check if bypass cut-off
valve is bound or
NO scored.
Faulty bypass cut-off
valve.
NO
Boom Lower Me-

ter-In Cut Valve
Boom Flow Rate

T1V1-03-03-026
T5-7-113
F-13 Attachment speed is fast during combined
operation of attachment (optional) and front
attachment (when secondary crusher or
primary crusher is used).

Related MC Fault Code: None NO ness between MC and
• Check the wiring connections first. Disconnect connec- pressure sensor (aux-
tor MC-D in MC. iliary).
between terminal
YES #D5 of harness end
of connector and tween terminals #D5
Disconnect connector terminal #2 of har-
in pressure sensor of harness end of
ness end of connec- connector MC-D and
(auxiliary). tor in pressure sen- YES
Check if voltage be- machine is 0 V.
NO tween terminals #1 sor (auxiliary).
· Key switch: ON
and #3 of harness
end of connector is
5±0.5 V.
Switch pressure · Key switch: ON Open circuit in har-
sensor (auxiliary) YES ness between MC and
with other pressure tween terminals #1 of pressure sensor (aux-
sensor. harness end of con- iliary) (terminal #3).
Check if fault code nector in pressure
for switched pres- NO sensor (auxiliary) and
sure sensor is dis- machine is between Open circuit in har-
played. 0.25 and 4.75 V. ness between MC and
pressure sensor (aux-
· Key switch: ON NO
iliary) (terminal #1).
Faulty pressure sen-

sor (auxiliary).
YES
open side)
Pilot Pressure Sensor (Auxiliary) MC
Pilot Pressure Sensor (Arm Roll-Out) Connector MC-A
#A7 #A23
T1V1-05-07-102
Auxiliary Flow Rate Control MC

Solenoid Valve Connector MC-D T183-05-04-008
#D5
T1V1-05-04-003
T183-05-04-009
#D9
T5-7-114
Disconnect connec- Check if voltage be-
tor MC-D in MC. YES tween terminals #D9
Check for continuity of harness end of To A
between terminal connector MC-D and
Disconnect connec- YES #D9 of harness end machine is 0 V.
tor in pressure sen- of connector and · Key switch: ON
sor (arm roll-out). terminal #2 of har-
NO Check if voltage be- ness end of connec- Open circuit in harness
Switch pressure tween terminals #1 tor in pressure sen- between MC and pressure
sensor (arm roll-out) and #3 of harness sor (arm roll-out). NO
sensor (arm roll-out).
with other pressure end of connector is
YES sensor. 5±0.5 V.
Check if fault code
for switched pres- · Key switch: ON Open circuit in harness
Check if voltage be- YES between MC and pressure
sure sensor is dis- tween terminals #1 of
played. sensor (arm roll-out) (ter-
harness end of con- minal #3).
nector in pressure
NO sensor (arm roll-out)
and machine is be-
tween 0.25 and 4.75 Open circuit in harness
V. between MC and pressure
NO sensor (arm roll-out) (ter-
· Key switch: ON minal #1).
Faulty pressure sensor

(arm roll-out).
YES

between MC and pressure
NO sensor (auxiliary).
Faulty auxiliary flow rate

YES
Check if auxiliary flow
YES rate control solenoid
valve is bound or Faulty auxiliary flow rate
scored. YES
Check if auxiliary control valve in control
Check for continuity in flow rate control valve.
harness between MC valve in control
YES and auxiliary flow rate NO valve is bound or
control solenoid valve. Faulty MC.
scored.
NO
· Between terminal
#A23 of connector Open circuit in harness
A MC-A in MC and ter- between MC and auxiliary
minal #1 of connector flow rate control solenoid
in auxiliary flow rate NO
valve.
connector in auxiliary
flow rate control sole-
noid valve
between MC and pres-
NO sure sensor (arm
roll-out).
T5-7-115
attachment (when breaker attached with
auxiliary flow combining line is used).
Shorted circuit in har-

Related MC Fault Code: None NO ness between MC and
• Check the wiring connections first. pressure sensor (aux-
Disconnect connec- iliary).
tor MC-D in MC.
YES Check if voltage be- Switch pressure sen-
tween terminal #D5 sor (arm roll-out) with
of harness end of other pressure sen-
Disconnect connector connector and ma- YES sor.
in pressure sensor chine is 0 V. Check if fault code for
(auxiliary). · Key switch: ON switched pressure
NO Check if voltage be- sensor is displayed.
tween terminals #1
and #3 of harness
Switch pressure end of connector is Open circuit in har-
sensor (auxiliary) 5±0.5 V. YES ness between MC and
with other pressure · Key switch: ON pressure sensor (aux-
sensor. iliary) (terminal #3).
Check if fault code Check if voltage be-
for switched pres- tween terminals #1 of
sure sensor is dis- harness end of con- Open circuit in har-
played. NO nector in pressure ness between MC and
sensor (auxiliary) and NO pressure sensor (aux-
machine is between iliary) (terminal #1).
0.25 and 4.25 V.
· Key switch: ON
Faulty pressure sen-

YES sor (auxiliary).
Connector (Harness end of connector viewed from the open

side)
Pilot Pressure Sensor (Auxiliary) MC
Pilot Pressure Sensor (Arm Roll-Out) Connector MC-A
#A7 #A23
T1V1-05-07-102
Auxiliary Flow Combining Solenoid Valve MC T183-05-04-008
Connector MC-D
#D5
T1V1-05-04-003
T183-05-04-009
#D9
T5-7-116

NO between MC and pres-
sure sensor (arm
roll-out).
MC-D in MC. Check if Disconnect connector
YES MC-B in MC and con-
voltage between ter- Check if auxiliary flow
Disconnect connector minals #D9 of harness nector in auxiliary flow NO combining solenoid
in pressure sensor end of connector and combining solenoid valve is bound or To A
(arm roll-out). machine is 0 V. valve. scored.
NO Check if voltage be- Check for continuity
tween terminals #1 YES between terminals #1
and #3 of harness end and #2 of harness end Shorted circuit in harness
of connector is 5±0.5 of connector in auxil- between MC and auxil-
V. iary flow combining
solenoid valve. YES iary flow combining so-
· Key switch: ON lenoid valve.

Check if voltage be- YES between MC and pres-
tween terminals #1 of sure sensor (arm roll-out)
harness end of con- (terminal #3).
nector in pressure
NO sensor (arm roll-out)
and machine is be- Open circuit in harness
tween 0.25 and 4.75 between MC and pres-
V NO sure sensor (arm roll-out)
· Key switch: ON (terminal #1).

YES (arm roll-out).
Faulty auxiliary flow

YES combining solenoid
valve.
A Faulty auxiliary flow

YES
Check if auxiliary flow combining valve.
combining valve in
NO control valve is bound
or scored. Faulty MC.
NO
T5-7-117
attachment (when vibrating hammer is
used).
Related MC Fault Code: None Disconnect connec- Open

MC circuit in harness
と圧力センサ(予
NO
tor MC-D in MC. between
備)間のハーネス断線MC and pres-
• Check the wiring connections first. Check for continuity sure sensor (auxiliary).
between terminal
YES #D5 of harness end
of connector and Checkコネクタのハー
MC-D if voltage be-
terminal #2 of har- tween terminals #D5
ネス側コネクタ#D5
ness end of connec- of harness end of
端子と本体間の電圧
Disconnect connector tor in pressure sen- YES を測定するMC-D and
connector
in pressure sensor sor. 電圧は 0Visか
machine between 0
(auxiliary). V.
NO Check if voltage be-
tween terminals #1 · キースイッチ:
Key switch: ONON
and #3 of harness
Switch pressure end of connector is Open
MC circuit in harness
と圧力センサ(予
sensor (auxiliary) between 5±0.5. YES between MC and pres-
備)(#3 端子)間のハー
with other pressure · Key switch: ON sure
ネス断線 sensor (auxiliary)
sensor. Check if voltage be- (terminal #3).
Check if fault code tween terminals #1 of
for switched pres- harness end of con-
sure sensor is dis- nector in pressure Open circuit in harness
played. NO sensor (auxiliary) and MC と圧力センサ(予
machine is between NO 備)(#1 端子)間のハー
sure sensor (auxiliary)
0.25 and 4.75 V. ネス断線
(terminal #1).
· Key switch: ON

(auxiliary).
YES
open side)
Pilot Pressure Sensor (Auxiliary) MC MC
Pilot Pressure Sensor (Travel) Connector MC-A Connector MC-C
#A3 #A20
T1V1-05-07-102
T183-05-04-008 T1V1-05-07-103
Maximum Pump 1 Flow Rate Limit MC
Control Solenoid Valve (Optional) Connector MC-D
#D5
T1V1-05-04-003
T183-05-04-009
T5-7-118
YES
To A
Disconnect connector YES tween terminals #C2
in pressure sensor of harness end of
(travel). connector MC-C and
NO Check if voltage be- machine is 0 V.
tween terminals #1 Shorted circuit in harness
· Key switch: ON between MC and pres-
and #3 of harness end NO sure sensor (travel).
Switch pressure sen- of connector is 5±0.5
YES sor (travel) with other V.
pressure sensor. · Key switch: ON
Check if fault code for Open circuit in harness
switched pressure Check if voltage be- YES between MC and pres-
sensor is displayed. tween terminals #1 of sure sensor (travel) (ter-
harness end of con- minal #3).
nector in pressure
NO sensor (travel) and
machine is between
0.25 and 4.75 V.
· Key switch: ON NO sure sensor (travel) (ter-
minal #1).

(travel).
YES

NO sure sensor (auxiliary).
in maximum pump 1 Faulty maximum pump 1
YES
flow rate limit control flow rate limit control
solenoid valve. solenoid valve.
YES Check if current be-
tween terminals #1
of connector is be-
Check for continuity in tween 56 mA and 920
harness between MC mA.
A and maximum pump 1
flow rate limit control Faulty MC.
· Key switch: ON
solenoid valve. NO
· Between terminal
#A20 of connector Open circuit in harness
MC-A in MC and ter- between MC and maxi-
minal #1 of connector NO mum pump 1 flow rate
in maximum pump 1 limit control solenoid
flow rate limit control valve.
solenoid valve
connector in maxi-
mum pump 1 flow rate
limit control solenoid
valve
T5-7-119
SWING SYSTEM TROUBLESHOOTING
S-1 Swing is slow or unmoving.

• Check whether the pilot system is faulty or the • In case left travel speed is also slow, refer to A-3.
main circuit is faulty.
• In case other functions (front attachment and
travel) operate normally, the pilot pump is consid-
ered to be normal. If the pilot system is displaying
a problem, the cause of trouble may exist in the
circuit after pilot valve.
Check if swing motor

YES parking brake release
valve is scored or
bound.
Check if parking brake
release pressure is
YES approx.2 3.9 MPa (40
kgf/cm ).
· Relieve arm circuit. Faulty swing parking
· Monitor item: brake release spool in
Monitor pump control Front attachment con- NO signal control valve.
pressure. trol pressure
YES While slowly operating
swing lever, check if service menu and
pump control pressure monitoring in monitor
varies smoothly. unit.
Monitor secondary · Monitor item:
pilot pressure. Pump 2 pump control
Check if secondary pressure Bound pump 2 flow rate
pilot pressure is nor- · Possible to display by control valve in signal
mal. service menu and control valve.
monitoring in monitor NO
· Specification:
unit.
Refer to Operational
Performance Test Sec-
tion.
· Monitor item: Faulty pilot valve.
Swing control pressure NO
service menu and
monitoring in monitor
unit.
T5-7-120
YES Faulty swing reduction

gear.
YES Check if swing motor drain

oil amount is normal.
· Measurement: Faulty swing motor.
NO Check if swing relief
Refer to Operational Per- NO
pressure is normal.
formance Test Section.
· Relieve swing circuit.
· Monitor item: Pump 2
delivery pressure
service menu and Faulty swing relief valve.
monitoring in monitor NO
unit
· Specification:
Refer to Operational
tion. Faulty swing motor park-
YES ing brake release valve.
T5-7-121
S-2 Swing is slow (weak in power) during com-
bined operation of swing and arm roll-in.
Swing does not start smoothly.
Swing power is weak.

11301-3, 11301-4, 11303-3, 11303-4

System group / Valve Control Circuit in the T/M
(Operational Principle).
YES sensor, or faulty MC.
between MC and sensor.

displayed. Install a pressure gauge
· Fault code to hose SE connecting
from signal control YES Faulty arm 1 flow rate
11202-3, 11202-4: control valve in control
Pump 2 delivery valve to arm flow rate
control valve in control valve.
pressure sensor
11301-3, 11301-4: valve.
NO When relieving during
Pressure sensor Bound control spool in
(swing) combined operation of
arm flow rate control
11303-3, 11303-4: swing and arm roll-in,
NO valve in signal control
Pressure sensor (arm check if pressure is 3.9
2 valve.
roll-in) MPa (40 kgfcm ).
NOTE: In case other fault

codes are dis-
played, perform
troubleshooting Signal Control Valve
corresponding to (Control Valve Side)
the displayed fault
code.
Hose SE
T178-03-06-015
Arm 1 Flow Rate

T1V1-05-04-004
Control Valve
T5-7-122
(Blank)
T5-7-123
TRAVEL SYSTEM TROUBLESHOOTING
T-1 Both right and left tracks do not rotate or
rotate slowly.
• Both right and left pilot valves, travel motors,

and/or control valve spools are unlikely to be
faulty at the same time.
• In case both travel systems do not operate, the
pilot system, which is applied to both side travel
motors, may be faulty. If primary pilot pressure is
lower than specification, front attachment operat-
ing speed becomes slow as well. Refer to A-1.
• In case the fast travel mode cannot be selected,
refer to T-5.
T5-7-124
(Blank)
T5-7-125
T-2 One side track does not rotate or rotates
slowly. Machine mistracks.
• Check that both side track sags are equally ad- • In one side track only does not rotate, the pilot
justed. valve, control valve, travel motor, or center joint
• Faulty pump control will cause the machine to may be faulty.
mistrack. In this case, other trouble symptoms
such as slow bucket or swing single operation
speed, or slow arm roll-in and boom raise speed Check if travel motor
YES drain oil amount is
in level crowd operation will occur at the same
time. If both mistrack and other symptoms as normal.
described above occurs at the same time, refer to · Measurement: Refer
A-3 and A-4. NO Check if travel relief to Operational Per-
pressure in slow speed formance Test Sec-
side is normal. tion.
· Relieve travel circuit.
· Monitor item: Pump 1
Check if symptom is and 2 delivery pressures Switch forward travel
· Possible to display by relief valve with reverse
YES reversed when right and service menu and travel one, or right
left travel line hoses are
switched each other at monitoring in monitor travel relief valve with
unit NO left one.
the top of center joint.
· Measurement: Check if symptom is
Refer to Operational reversed.
Check if secondary tion.
travel pilot pressure is
normal. Bound control valve
· Monitor item: Travel con- YES spool.
trol pressure
Faulty pilot valve.

NO
Relationship between Faulty Seal Location

Seal Location
and Mistrack Direction
Seal When traveling When pivot turn
No. straight: is performed:
External Oil 1
1 ←
Leak
2
2
3
3
Left Travel Right
(Reverse) Travel
(Reverse)
4 4
Left Travel 5 Right
(Forward) Travel
5 (Forward)
6
7
6
T105-07-04-015
External Oil ←
7 Leak
T5-7-126
NO Faulty travel motor.
YES Faulty travel reduction

gear.
Disassemble and clean
YES travel motor servo piston.
Check if same symptom Faulty travel motor servo
Disassemble and clean occurs. piston.
travel motor counter-
balance valve. NO
YES Check if same symptom
occurs. Faulty counterbalance
NO valve.
NO Faulty center joint.
Faulty travel relief valve.

YES
Arrangement of Pipe Line

Front
1 2
5 4
W157-03-03-003
1 - Left Travel (Forward) 3 - Pilot 5 - Left Travel (Reverse) 6 - Drain

2 - Right Travel (Forward) 4 - Right Travel (Reverse)
T5-7-127
T-3 Machine mistracks during combined opera-
tion of travel and front attachment.
Related Fault Code: None
Faulty flow combiner

YES
valve control spool in
signal control valve.
Remove hose (SL) from
signal control valve to
flow combiner valve.
NO Install a pressure gauge.
YES Faulty load check
Check if signal pressure valve.
is approx. 3.9 MPa (40
2
kgf/cm ). Check load check
valve for any abnor-
NO mality.
Check flow combiner Find out cause of trou-
valve in control valve ble by tracing other
for any abnormality. NO trouble symptoms.
Faulty flow combiner

YES valve.
Signal Control Valve (Control Valve Side)
Flow Combiner
Hose (SL) T178-03-06-015 Valve
T1V1-05-04-005
T5-7-128
T-4 Occasionally, machine may mistrack when
traveling with engine running at slow speed.

11202-3, 11202-4, 11304-3, 11304-4, 11307-3,
11307-4, 11401-2, 11401-3, 11401-4
• Refer to the pages for the SYSTEM / Control

System group / Travel Torque-Up Control in the
T/M (Operational Principle).
• Check the wiring connections first. Faulty corresponding
sensor, or open circuit in
corresponding sensor.
YES Faulty torque control so-
lenoid valve and faulty
MC.
between torque control
Check is fault code is solenoid valve and MC.
displayed.
· Fault codes:
11200-3, 11200-4: Monitor output pressure
Pump 1 delivery pres- from torque control sole- YES Faulty pump device.
sure sensor noid valve. Install a pres-
11202-3, 11202-4: sure gauge to torque
Pump 2 delivery pres- control solenoid valve
sure sensor output port.
11304-3, 11304-4: Check if both pressures
Pressure sensor NO measured by pressure
(travel) gauge and Dr. ZX varies
11307-3, 11307-4: identically by approx. 1.5
2 Faulty pressure sensor
Pressure sensor (front MPa (15 kgf/cm ) when
NO (travel).
attachment. travel operation is made.
11401-2, 111401-3,
· Monitor item:
11401-4: Torque con-
Pump torque proportional
trol solenoid valve
solenoid valve output
· Engine:
service menu and
Running at slow idle
monitoring by monitor
speed
unit.
T5-7-129
T-5 Fast travel is not operated.
Travel mode does not change from slow
mode to fast mode.

11202-3, 11202-4, 11206-3, 11206-4, 11208-3,
11208-4, 11304-3, 11304-4, 11307-3, 11307-4,
11405-2, 11405-3, 11405-4
• Refer to the pages for the SYSTEM / Control sec- • If the maximum speed cannot reach at the fast
tion / Travel Motor Swash Angle Control in the mode, the engine speed automatic increase con-
T/M (Operational Principle). trol at travel may be faulty. Refer to “E-6 Faulty
• Check the wiring connections first. HP Mode”.
Faulty travel mode switch, or
NO open circuit in harness be-
tween travel mode switch and
MC.
Monitor travel mode Check if symptom is re-
switch. NO versed when pressure sen-
NO Check if displayed indi- sor (travel) is switched with
cation is highlighted in another pressure sensor.
response to travel mode
switch operation.
mode Monitor pressure sen-
· Possible to display by sor (travel).
service menu and moni- Check if pressure var-
YES ies in response to travel
toring by monitor unit
lever operation.
control pressure
displayed.
service menu and moni- Check if travel motor
· Fault Code:
toring by monitor unit. swash angle control valve
11200-3, 11200-4:
YES is bound or scored.
Pump 1 delivery pres-
sure sensor
11202-3, 11202-4:
Pump 2 delivery pres-
sure sensor
11206-3, 11206-4:
Pump 1 control pres-
sure sensor
11208-3, 11208-4: Faulty corresponding sensor,
Pump 2 control pres- or open circuit in harness be-
sure sensor tween MC and sensor.
11304-3, 11304-4: Faulty solenoid valve unit (SI),
YES or open circuit in harness be-
Pressure sensor
(travel) tween solenoid valve unit (SI)
11307-3, 11307-4: and MC.
Pressure sensor (front
attachment)
11405-2, 11405--3,
11405-4: Solenoid
valve unit (SI)
NOTE: In case other fault

codes are displayed,
perform troubleshoot-
ing corresponding to
the displayed fault
code.
T5-7-130
YES Faulty pressure sensor (travel).
Open circuit in harness be-

tween pressure sensor (travel)
NO and MC, or clogged shuttle
valve in signal control valve.
YES Faulty travel motor swash an-

gle control valve.
Faulty travel motor, or faulty

NO travel reduction gear.
T5-7-131
OTHER SYSTEM TROUBLESHOOTING
O-1 Wiper is not operated.
Checking Instructions
• The wiper is driven by electric power routed via

the relay circuit. The relay circuit is controlled by
the monitor unit. In case the wiper is not operated,
first check if the wiper relay is activated. Next,
check if electric power is routed to the wiper mo-
tor.
YES
Switch wiper relay with Faulty wiper relay.
NO other general relay. Disconnect connector YES
Check if wiper is oper- monitor-A in monitor Faulty monitor unit.
ated. unit.
· Key switch: ON Connect terminal #A2
NO of harness end of con-
nector to machine. Open circuit in harness
Disconnect wiper relay. between wiper relay and
Check for continuity NO monitor unit.
Check if wiper relay between terminal #A2
is turned ON/OFF of harness end of con-
according to INT. nector and machine.
position of wiper
switch. YES
Close front window. Faulty wiper motor.
· Key switch: ON Disconnect connector
· Wiper switch: INT YES in wiper motor.
Open front window. Check if voltage be-
tween terminals B and Open circuit in harness
L of harness end of between window con-
tween terminals B NO
connector is 24 V. tact and wiper motor.
YES and L at window
contact in cab end is · Key switch: ON
24 V. · Wiper switch: ON
· Key switch: ON Open circuit in harness
· Wiper switch: ON NO between wiper relay and
window contact.
Window Contact (Cab end) Connector

Wiper Motor (harness end)
INT. Position Setting Time
Slow Speed 8 seconds
Middle Speed 6 seconds B L
Fast Speed 3 seconds

S E
T1V1-05-07-005
Monitor Unit
Connector Monitor-A (harness end) #A2
T183-05-05-001
T5-7-132
Wiper Driving Circuit
Wiper Motor Wiper Relay
Main
Window Contact ↑
T1V1-05-07-004
T5-7-133
O-2 Air Conditioner is faulty
The air conditioner operation system has a

self-diagnosing function. This system performs the
diagnosis by 8-steps as shown in the flow chart be-
low: Check Model Confirmation, Display Function
Confirmation, Present Trouble Diagnosing, Past
Trouble Diagnosing, Sensing Temperature Display,
and Component Operation Check, Correction of the
Set Temperature and Selection of Celsius and Fahr-
enheit Temperature Indication.
Normal Operation
Turn key switch ON while pushing air

conditioner switch and mode switch.
Keep pushing OFF switch

for more than 3 seconds. STEP 0
Check Model Confirmation
Push lower side fan switch. Push upper side fan switch.
Keep pushing OFF switch STEP 1
for more than 3 seconds. Display Function
Confirmation
Keep pushing OFF switch STEP 2
for more than 3 seconds. Present Trouble
Diagnosing
Keep pushing OFF switch STEP 3 Keep pushing air conditioner

for more than 3 seconds. Past Trouble switch for more than 3 seconds.
Diagnosing
Sensing Temperature
Display
Component Operation Check
Push AUTO switch and Push AUTO Push A/C Push A/C switch and
lower side fan switch. Switch and switch and upper side fan switch.
upper side lower side
fan switch. fan switch.
Keep pushing OFF switch STEP 6-1 STEP 6-2
for more than 3 seconds. Correction of the Set Selection of Celsius and Fahrenheit
Temperature Temperature Indication
for more than 3 seconds.
Self-Diagnosis
T5-7-134
Self-Diagnostic System Activation
Fan Switch LCD Air Conditioner Switch
Turn the key switch ON while pushing the air condi-
tioner switch and mode switch on air conditioner con-
trol panel.
STEP 0 Check Model Confirmation

The liquid crystal display (LCD) indicates the ma-
chine model name this system can diagnose. T178-05-08-001
Mode Switch OFF Switch

• The LCD will indicate “Sd” as the check model
name.
• Select next step in order to be performed by oper-
ating the switch as described below.
• Upper side fan switch: To proceed to Step 1
• Keep pressing OFF switch for more than 3 sec-
onds: To return to normal operation
NOTE: The system operation will automatically
proceed to STEP 1 after 5 seconds have
pushed after the check model is displayed.
STEP 1 Display Function Confirmation

Turn all indicators ON in order to check indicator
bulbs.
• The LCD panel and all switch indicators light.

• Select the next step in order to be performed by op-
erating the switches as follows:
• Push the upper side of fan switch: To proceed to
“STEP 2.”
• Push the lower side of fan switch: To return to
“STEP 0.”
• Keep pushing the OFF switch for more than 3
seconds: Deactivate the self-diagnostic system.
(Normal function is resumed.)
T5-7-135
STEP 2 Present Trouble Diagnosing
The LCD indicates the fault codes for present ab-
Fan Switch LCD
normalities of the mix door, mode encoder, and/or
sensors.
• In case any abnormalities are present, the LCD in-

dicates the fault codes. If more than one fault code
is detected, the following fault code is displayed af-
ter flashing (0.5 seconds) twice.
Fault Code T178-05-08-001
Open Circuit Shorted Circuit OFF Switch
Mix Door 21 −21
Mode Encoder 22
In-Cab Ambient 23 −23
Temperature
Sensor
Outdoor Ambient 24 −24
Temperature
Sensor
Coolant Tem- 25 −25
perature Sensor
∗
Solar Radiation 26 −26
Sensor
∗
: When solar radiation is shaded, the solar radiation
sensor indicates the fault code of open circuit.
“STEP 3.”
“STEP 1.”
(Normal function is resumed)
T5-7-136
STEP 3 Past Trouble Diagnosing
The LCD indicates the fault codes for past abnor-
malities of the mix door, mode encoder, and/or sen-
sors.
The past stored fault codes are deleted.
• In case any abnormalities occurred in the past, the

LCD indicates the fault codes. If more than one fault
code is detected, the following fault code is dis-
played after flashing (0.5 seconds) twice. T178-05-08-001
Fault Code OFF Switch
Open circuit Shorted Circuit
Mix Door 21 −21
Mode Encoder 22
In-Cab Ambient
Temperature 23 −23
Sensor
Outdoor Ambient
Temperature 24 −24
Sensor
Coolant Tem- 25 −25
perature Sensor
Solar Radiation −26
Sensor
• When the air conditioner switch is kept pushing for
more than 3 seconds, the failure records are de-
leted. After this operation, the air conditioner switch
indicator flashes 5 times. Then, the self-diagnosing
system is deactivated. (Normal functions are re-
sumed.)
“STEP 4.”
“STEP 2.”
T5-7-137
STEP 4 Sensing Temperature Display Fan Mark
The LCD indicates the sensing temperature detected
by each temperature sensor (excluding the insulation
sensor).
• The sensing temperature detected by the in-cab

ambient temperature sensor, outdoor ambient tem-
perature sensor and coolant temperature sensor are
displayed on the LCD in real time. (Figures less
than the decimal point are not displayed.) T178-05-08-001
NOTE: The coolant temperature sensor indicates Fresh Air Vent Switch OFF Switch
“H” when coolant temperature is more than
21 °C (70 °F) and “L” when coolant tem-
perature is less than 21 °C (70 °F).
• Sensing temperature detected by each sensor is
automatically displayed on the LCD and is cycled at
an interval of 3 seconds with the timer. The timer is
turned ON or OFF by operating the fresh air vent
switch.
• Referring to the fan mark can check which sensing
temperature is displayed.
“STEP 5.”
“STEP 3.”
T5-7-138
STEP 5 Component Operation Check Air Conditioner
Fan Switch LCD Switch AUTO Switch
Each component operation is checked by performing
pattern operation.
• Each time the fresh air vent switch is pushed, the

component to be checked is selected in order.
Check which component has been selected by re-
ferring to No. indicated on the LCD. (Refer to table
1.) T178-05-08-001
• Operating pattern of the selected component is
Fresh Air Vent switch OFF Switch
shifted at an interval of 10 seconds. Operating pat-
tern is cycled. (Refer to table 1.)
NOTE: The components other than selected oper-
ate under the standard conditions (shown
by marks* in table 1).
• Push the AUTO switch and upper side of fan
switch: To proceed to “STEP 6-1”.
• Push the A/C switch and upper side of fan switch:
To proceed to “STEP 6-2”.
“STEP 4.”
Table 1
Component Indication Operation Pattern Remarks
on LCD
Air Mix Damper 51 Controls opening extent of air mix 0%, 50%, 100%: “C”, “5” and “H” are in-
damper: 0% (fully closed) → dicated next to the decimal point respec-
50%*→ 100% (fully opened) tively.
Fan 52 Controls air flow volume: Lo → Indicators corresponding to air flow vol-
M(Lo) → M(Hi) → Hi ume light.
Air Vent Location 53 Selects air vent: Front*→ Indicator corresponding to selected air
Front/Rear → Front/Foot → Foot vent lights.
Fresh / Circulation 54 Select Ventilation Mode: Circula- Indicator corresponding to selected
Air Vent Selection tion* → Fresh mode light.
Air Conditioner 55 Turns air conditioner switch: ON* ON: Indicator lights.
→ OFF OFF: Indicator is extinguished.
T5-7-139
STEP 6-1 Correction of the Set Temperature
Fine correction of the set temperature. Temperature
Fan Switch LCD Control Switch AUTO Switch
• Each time when the top or bottom of temperature

control switch is pushed, temperature correction,
displayed on the LCD window, can be changed.
• Actually controlled temperature is the normally set
temperature plus the set temperature correction.
For instance, when the normally set temperature is
25°C (77 °F) and set temperature correction is -1°C T178-05-08-001
(-34 °F), the actually controlled temperature be- OFF Switch

comes 24°C (75 °F).
• Push the AUTO switch and lower side of fan
switch: To return to “STEP 5.”
T5-7-140
STEP 6-2 Selection of Celsius and Fahrenheit
Temperature Indication
Selection of Celsius and Fahrenheit Temperature In-
dication.
• Each time when the fresh air vent switch is pushed,
Celsius or Fahrenheit temperature may be dis-
played alternately.
• Temperature is displayed at the top of LCD window
as follows.
(C: Celsius, F: Fahrenheit) T178-05-08-001
C F Fresh Air Vent Switch OFF Switch

• Push the Air Conditioner Switch and lower side of
fan switch: To return to “STEP 5.”
T5-7-141
※ Please fill in all sections and return this AIR CONDITIONER TROUBLE REPORT to Hitachi Tsuchiura Works Quality Assurance Dept. af-
ter experiencing a problem with your machine’s air conditioning system.
< AIR CONDITIONER TROUBLE REPORT > File No.
(1) What Checked by:
Model (Serial No. )
Operation Type Manual Semi-Auto Full-Auto
Delivery Date Year Month
(2) When
Date Year Month Day Operating Hour ( h)
Time Morning Daytime Evening Night
Frequency Every Day Once a Week Once a Month Times per
(3) Where
Job Site Address State County Town
Access Road Condition Paved Not Paved (Gravel Sand Soil)
(4) How (Operating Conditions)
Weather Fine Cloudy Rain Snow
Atmospheric Temperature Very Hot Hot Cold Very Cold
Operating Conditions Parking Traveling Working
Temperature Control Paint blanks equal to red indicators. / Fill in set-temperature when
full-auto operation
A/C ON OFF
Control Air Induction Re-Circulation Fresh Air Circulation
Panel AUTO ON OFF Not Available
Fill following items when operated in manual mode or when manual control type unit is used.
Vent Position Front Front / Rear Foot Front / Rear and Foot
Fan First Second Third Fourth Fifth Sixth
(5) How (Problem Symptom)
Abnormal Compressor Operation
Symptom Not turned ON <Check Result>
Not turned OFF (1) Is problem reproducible ?
Others Reproducible
Uncontrollable air temperature Not reproducible
Symptom No cool air (2) Pressure (To be measured at gauge manifold)
No warm air Low Pressure
Others High Pressure
Uncontrollable air volume (3) Which parts have been replaced ?
Symptom Air flows in Hi mode only 1
No air flows
2
Small air volume
Others
Uncontrollable vent hole ∗ Before replacing the control amplifier, be sure to
Symptom Vent hole isn’t selected check that the connectors are correctly connected
while repeatedly disconnecting and reconnecting
Others
connectors.
Abnormal panel indication
Faulty Indica- Vent Hole
tor A/C
AUTO
Fresh Air Circulation
Fan OFF
Fan (Lo • •• Hi)
Temperature Control
Symptom Stays OFF
Stays ON
Blinks
Others
T5-7-142
Refrigerant Quantity....................... 850±50 g

3
Compressor Oil Quantity................ 210 cm
T5-7-143
Cooling Circuit
Refrigerant pressure Bubbles can be seen in sight Piping and/or parts are stained with oil,
in both high and glass. respond to gas detector.
low-pressure sides is
low.
No oil stain is found or gas detector
does not respond. Refrigerant has not
been refilled for longer than one sea-
son.
No bubbles are seen in sight
glass.
After cooling at fast speed continu-

ously, cooling power is reduced. Air
flow volume remains unchanged.
Air flow volume is reduced.
Refrigerant pressure
in low-pressure side Bubbles can be seen in sight Compressor cylinder is extremely hot,
Insuffi- is high. glass. emitting a smell.
cient
Cooling
Power
Refrigerant pressure in Compressor cylinder is extremely hot,
high-pressure side is low. emitting a smell.
Heater unit emits hot air.
Refrigerant pressure
in high-pressure side Bubbles can be seen in sight Refrigerant pressure in low-pressure
is high. glass. side is low.
Condenser is stained and clogged.
Even if condenser is sprayed with water, few bubbles appear. Receiver dryer tem-
perature is low.
After cooling at fast speed continu-

ously, cooling power is reduced. Air Frost forms. Thermistor does not cool.
flow volume is reduced.
Thermistor cools.
T5-7-144
Gas leaks from pipe joints and/or parts. Re-tighten or replace parts.
Normal leakage of refrigerant from hoses. Refill refrigerant.
Improper adjustment (excessive restriction) of expansion valve. Readjust or replace expansion valve.
Clogged expansion valve. Remove clog, or replace receiver and/or expansion

valve.
Clogged low-pressure circuit and/or evaporator. Remove clog, or replace parts.
Frozen expansion valve or water in circuit. After evacuation, refill refrigerant and/or replace re-
ceiver dryer.
Gas leaks from case. Seal gaps by using vinyl tape or packing compound.
Poor contact of expansion valve temperature sensing cylinder. Make good contact. Replace temperature sensing
stay.
Improper adjustment (excessive open) of expansion valve. Readjust or replace.
Insufficient compressor discharge (faulty gasket and/or valve). Replace.
Improper water stop valve wire adjustment and/or faulty stop

valve. Check and readjust or replace.
Poor airtight fitting of outside air damper (outside air induction

Repair.
type).
Clogged high-pressure circuit before receiver dryer. Remove clog, or replace parts.
Clean Condenser.
Excessive refrigerant. Remove excessive refrigerant to proper level.
After evacuation, refill refrigerant and/or replace re-

Air is mixed in system.
ceiver dryer.
Incorrect thermistor location. Correct thermistor location.
Gas leaks from case. Seal gaps by using vinyl tape or packing compound.
Faulty thermistor (stays ON). Disconnected thermistor cord.
Even if function and performance are normal, when Instruct user on correct air-conditioner operation.
air-conditioner is kept operated for a long time with thermistor (Reset thermistor to either minimum or middle cooling
in max. cooling position and air flow in M or L mode, frost may position or increase air flow.)
form.
T5-7-145
Cooling Circuit
Case connection. Louver resonance.
Fan contacts case, or foreign matter enters case.

Blower fan connection.
Brush friction noise, metal and/or thrust washer contact
noise.
Gas blowing sound (roaring). Gas vibration noise (compressor discharge and/or suc-
tion gas noise).
Expansion valve connection, whistle Abnormal noise from expansion valve (Expansion
Noise sound, gas blowing sound. valve is normally functioning.).
Faulty clutch bearing, and/or idle pulley bearing.
Clutch disengaging sound.

Contact of clutch amature due to resonance, or loose
belt and/or screws.
Noisy compressor.
Compressor rotating sound.
Vibration and/or loose screws due to excessive drive
belt looseness.
Broken heater core and/or hose.

Water leak and/or splash.
Clogged case drain port and/or drain hose.
Others
Absorbed cigarette and dust smell on evaporator fins.

Abnormal smell.
T5-7-146
Repair or replace.
Remove foreign matter. Readjust fan motor location.
Slight noise is unavoidable.

Replace if loud.
No functional problem exists.

Provide silencer if intolerable.
Replace expansion valve if whistle sound is heard. Gas flow noise can be slightly heard.
Replace.
Repair or replace clutch. Re-tighten screws.
Repair or replace.
Re-adjust drive belt.
Replace.
Clean.
-1
Clean evaporator. When humidity is high, open door. While rotating fan at approx. 1500 min in L
mode for more than 10 minutes, flush smell out by condensed water.
T5-7-147
Compressor
Compressor does not rotate. Clutch terminal voltage is normal 24 V.
Inoperable
cooling Clutch terminal voltage is low.
system.
Clutch terminal voltage is 0 V.
Bubbles exist even after refrigerant is refilled.
Both high and

low side Check for oil and refrigerant leaks from parts other than
pressures are compressor and pipe joints by using gas detector.
low.
Both com- Check for oil and refrigerant leaks from compressor (no
pressor and leaks from parts other than compressor) by using gas
blower mo- detector.
tor rotate. (Refer to NOTE 1, 2
on page T5-7-151.)
Stain on exterior.
Refrigerant has not been refilled for longer

than one season.
Refrigerant is discharged within 1 to 2

months after being recharged. Check for
refrigerant leaks using gas detector.
Refrigerant is kept charged for longer than

2 years.
Compressor cylinder is not hot. (Refrigerant returns to com-

High pressure side is pressor in liquid form.)
slightly low and low pres-
sure side is high.
No refrigerant returns in liquid form. High pressure side is low.
Bubbles can be seen through Others

sight glass.
High pressure side is high.
Refer to the Cooling Circuit Troubleshooting
Table on page T5-7-136.
Temperature is not cooled when compressor is
operated at fast speed continuously.
Air flow from blower is insufficient.
T5-7-148
Seized clutch. Replace.
Improper gap between amature and rotor (improper air gap).

Replace.
Open or shorted circuit in core cable.
Shaft does not rotate (internally locked). Replace.
Faulty Electrical System.
Faulty Electrical System.
Oil leaks from mechanical seal, gasket, and/or charge valve.

Replace.
Oil leaks from oil plug.
Oil and refrigerant leaks from front housing, and/or cylinder block joint. Replace.
Normal leaks from hoses. Charge

refrigerant.
No leaks (normal).
Refer to the Cooling Circuit Troubleshooting Table on page T5-7-136.
Broken valve (Refer to NOTE 3 on page T5-7-151.)
Replace.
Blown gasket (Refer to NOTE 3 on page T5-7-151.)
Check and adjust

Excessive oil. oil level.
T5-7-149
Compressor
Compressor rotation is abnormally draggy.

Overheating
is susceptible
to occur.
Trouble other than compressor. Refer to the Cooling Circuit Troubleshooting Ta-
ble on page T5-7-136.
Noise is heard when clutch is OFF.
Abnormal
noise
Noise is heard when clutch is ON.
T5-7-150
Broken clutch bearing due to overly tightened belt. Replace.
Shaft does n’o rotate.

Replace.
Shaft rotates draggy.
Broken clutch bearing.

Replace.
Contact or slip due to poor air gap.
Faulty idle pulley bearing.
Refer to the Cooling Circuit

Saggy belt. Troubleshooting Table on
page T5-7-136.
Loose screws.
Broken valve.
Replace.
Blown gasket.
Abnormal internal noise. Replace.
Vibration due to saggy belt.

Refer to the Cooling Circuit
Troubleshooting Table on
Loose screws. page T5-7-136.
NOTE:
1. Do not quickly decide that oil is leaking when a stain around the clutch and/or gasket is found. A
slight oil seepage will appear due to the seal construction. However, this oil seepage will not
cause malfunction. Accurately check whether oil is leaking or seeping only.
2. When gas detector is used in the high sensitivity range, normal gas leaks from rubber hose sur-
face may be detected. As long as the specified rubber hoses are used, the problem should not
occur. (In case a large leaks is detected, the hose may be broken.)
3. After allowing the compressor to idle for 10 to 15 minutes, normal pressure difference between
2
high-pressure side and low-pressure side is 0.5 MPa (5 kgf/cm ) or less. When the clutch is
turned OFF, the pressure difference between high-pressure side and low-pressure side will dis-
appear within about 10 seconds.
T5-7-151
EXCHANGE INSPECTION
Exchange inspection method is a troubleshooting
method to find the trouble location by exchanging the
suspected part / component with another part
/component having identical characteristics.
Pump 2 Pump 1
Many sensors and solenoid valves used on this ma- (5-Spool (4-Spool
chine are identical. Therefore, by using this Section) Section)
switch-check method, faulty part /component, and/or
harness can be easily found.
PP2 PP1
Example: Abnormal pump 1 delivery pressure high
voltage (MC fault code: 11200-3)
Check Method:
1. Switch two delivery pressure sensors located as
Figure A
shown in figure A to figure B.
2. Retry troubleshooting. T157-07-04-006
Result:
In case abnormal pump 2 delivery pressure high volt-
age is displayed (MC fault code 11202-3), the pump 1
delivery pressure sensor is considered to be faulty.
Pump 2 Pump 1
In case abnormal pump 1 delivery pressure high volt- (4-Spool
(5-Spool
age is displayed (MC fault code 11200-3), the pump 1 Section) Section)
delivery pressure sensor harness is considered to be
faulty.
PP1 PP2
Figure B T157-07-04-006
T5-7-152
Applicability of Switch-Check Method
Fault Code Trouble Applicability
11000-2 Abnormal EEPROM Not Applicable
11001-2 Abnormal RAM
11002-2 Abnormal A/D Conversion
11003-2 Abnormal Sensor Voltage
11004-2 CAN Communication Error Not Applicable
11100-2 Abnormal Engine Speed Not Applicable
11101-3 Abnormal Engine Control Dial Sensor High Not Applicable
Voltage
11101-4 Abnormal Engine Control Dial Sensor Low Not Applicable
Voltage
11200-3 Abnormal Pump 1 Delivery Pressure Sen- Applicable (Harness)
sor High Voltage
sor Low Voltage
sor High Voltage
sor Low Voltage
11206-3 Abnormal Pump 1 Control Pressure Sensor Applicable (Harness)
High Voltage
Low Voltage
High Voltage
Low Voltage
11301-3 Abnormal Swing Pilot Pressure Sensor Applicable (Harness/ Sensor)
High Voltage
11301-4 Abnormal Swing Pilot Pressure Sensor Low Applicable (Harness/ Sensor)
Voltage
11302-3 Abnormal Boom Raise Pilot Pressure Sen- Applicable (Harness/ Sensor)
sor High Voltage
11302-4 Abnormal Boom Raise Pilot Pressure Sen- Applicable (Harness/ Sensor)
sor Low Voltage
11303-3 Abnormal Arm Roll-In Pilot Pressure Sen- Applicable (Harness/ Sensor)
sor High Voltage
11303-4 Abnormal Arm Roll-In Pilot Pressure Sen- Applicable (Harness/ Sensor)
sor Low Voltage
11304-3 Abnormal Travel Pilot Pressure Sensor Applicable (Harness/ Sensor)
High Voltage
11304-4 Abnormal Travel Pilot Pressure Sensor Low Applicable (Harness/ Sensor)
Voltage
11307-3 Abnormal Front Attachment Pilot Pressure Applicable (Harness/ Sensor)
Sensor High Voltage
11307-4 Abnormal Front Attachment Pilot Pressure Applicable (Harness/ Sensor)
Sensor Low Voltage
11400-2 Abnormal Feedback Current of Maximum Applicable (Harness)
Pump 2 Flow Rate Limit Control Solenoid
Valve
11400-3 Abnormal Feedback High Voltage of Maxi- Applicable (Harness)
mum Pump 2 Flow Rate Limit Control So-
lenoid Valve
T5-7-153
Fault Code Trouble Applicability

11400-4 Abnormal Feedback Low Voltage of Maxi- Applicable (Harness)
lenoid Valve
11401-2 Abnormal Feedback Current of Torque Applicable (Harness)
11401-3 Abnormal Feedback High Voltage of Torque Applicable (Harness)
11401-4 Abnormal Feedback Low Voltage of Torque Applicable (Harness)
11402-2 Abnormal Feedback Current of Solenoid Applicable (Harness/ Solenoid
Valve Unit (SF) Valve)
11402-3 Abnormal Feedback High Voltage of Sole- Applicable (Harness/ Solenoid
noid Valve Unit (SF) Valve)
11402-4 Abnormal Feedback Low Voltage of Sole- Applicable (Harness/ Solenoid
noid Valve Unit (SF) Valve)
Valve Unit (SC) Valve)
noid Valve Unit (SC) Valve)
noid Valve Unit (SC) Valve)
Valve Unit (SG) Valve)
noid Valve Unit (SG) Valve)
noid Valve Unit (SG) Valve)
Valve Unit (SI) Valve)
noid Valve Unit (SI) Valve)
noid Valve Unit (SI) Valve)
11410-2 Abnormal Feedback Current of Maximum Applicable (Harness)
Pump 1 Flow Rate Limit Control Solenoid
Valve
11410-3 Abnormal Feedback High Voltage of Maxi- Applicable (Harness)
lenoid Valve
11410-4 Abnormal Feedback Low Voltage of Maxi- Applicable (Harness)
lenoid Valve
11910-2 Actual Engine Speed Not Applicable
11918-2 Work Mode Not Applicable
11911-2 Security Signal Not Applicable
11920-2 Fuel Flow Rate Not Applicable
11914-2 Radiator Coolant Temperature Not Applicable
11901-3 Abnormal Hydraulic Oil Temperature Not Applicable
Sensor High Voltage
11901-4 Abnormal Hydraulic Oil Temperature Not Applicable
Sensor Low Voltage
T5-7-154
EMERGENCY BOOM LOWERING PRO-
CEDURE
CAUTION: Prevent personal injury. Confirm Emergency Valve

that no one is under the front attachment
before starting the procedure below.
If the engine stalls and cannot be restarted, lower the

boom to the ground referring to the emergency boom
lowering procedure stated below.
1. Loosen lock nut (1) in the control valve at the right.

Loosen screw (2) one half of a turn. The boom
lowering speed can be somewhat adjusted by
loosening screw (2) more.
IMPORTANT: Lock nut (1) and screw (2) are lo-

cated under the solenoid valve.
Pay attention to the screw turns.
T1V1-05-04-005
2. After the boom is lowered, tighten screw (2) and

tighten lock nut (1) to the specifications below.
Lock Nut (1)

: 13 mm
: 13 N⋅m (1.3 kgf⋅m, 9.4 lbf⋅ft) Emergency Valve
Screw (2)
: 4 mm (Hexagonal wrench) 1
: 6.9 N⋅m (0.7 kgf⋅m, 5.0 lbf⋅ft)
2
NOTE: Excessive leakage may result if the screw
and the lock nut are tightened insufficiently.
Retighten the screw and the lock nut to
specifications.
T178-05-04-003
T5-7-155
ATTACHMENT PILOT CIRCUIT PRESSURE
RELEASE PROCEDURE
As for the attachment spec machine, the accumulator
is equipped between pilot pump and pilot valve.
After the engine stops, when the control lever is oper-

ated by the emergency stop switch with the pilot
shut-off lever ON, the accumulator releases pressure
in the pilot circuit.
Auxiliary Pilot Travel Pilot

Valve Right Pilot Valve Left Pilot Valve Valve
To Control Valve
Pilot Shut-Off
Lever: ON
Accumulator
Pilot Shut-Off
Solenoid Valve Pilot Pump
T1V1-05-07-006
Engine
T5-7-156
(Blank)
T5-7-157
ONE PART OF DATA, “DAILY REPORT
DATA”, “DISTRIBUTION DATA” AND TO-
TAL OPERATING HOURS” IS NOT RE-
CORDED
• The required signal for data may not be sent to

ICF. As each signal is used for some data, check
the corresponding signal system according to the
table below.
Data Input Signal

Daily report data is not recorded. Key switch, alternator
Fuel Level Fuel sensor data sent from monitor unit
Fuel Usage Amount Value is calculated and recorded by accumulated fuel us-
age amount from ECM.
Machine Hour Meter Hour meter sent from monitor unit
T5-7-158
Position to be checked Remedy

Key signal line, alternator signal line Check if voltage between terminal #C7 (power ON signal line) of
connector ICF-C in ICF and machine is 24 V or more.
Communication line between monitor unit and ICF • Check for continuity between terminals #C5 of connector ICF-C in
(CAN bus line) ICF and terminals #B7 of connector monitor-B in monitor unit.
(Refer to T5-7-161.)
• Check for continuity between terminals #C11 of connector ICF-C
in ICF and terminals #B6 of connector monitor-B in monitor unit.
• Check for shorted circuit in harness between CAN circuit in
ground circuit. (Refer to T5-6-62.)
• Check for shorted circuit in harness between CAN circuit in power
circuit. (Refer to T5-6-65.)
• Check for shorted circuit in harness between CAN circuit in key
signal circuit. (Refer to T5-6-68.)
• Check for shorted circuit in CAN harness. (Refer to T5-6-70.)
Communication line between ECM and ICF (CAN • Check for continuity between terminals #C5 of connector ICF-C in
bus line) ICF and terminals #18 of connector in ECM. (Refer to T5-7-160.)
in ICF and terminals #37 of connector in ECM. (Refer to
T5-7-160.)
(CAN bus line) ICF and terminals #B7 of connector monitor-B in monitor unit.
in ICF and terminals #B6 of connector monitor-B in monitor unit.
T5-7-159
Data Input Signal

Engine Operating Hours HP Mode Hours Power mode switch information sent from MC
P Mode Hours Power mode switch information sent from MC
E Mode Hours Power mode switch information sent from MC
Auto-Idle Switch ON Hours Auto-idle switch information sent from MC
Travel Operating Hours Fast Idle (Hi) Traveling Hours Travel mode switch information sent from MC
Slow Idle (Lo) Traveling Hours Travel mode switch information sent from MC
Swing Operating Hours Swing pressure sensor (swing) information sent from MC
Digging Operating Hours Front attachment pressure sensor (front attachment) in-
formation sent from MC
Attachment Operating Hours Breaker Operating Hours Attachment information sent from MC
Secondary Crusher Operating Attachment information sent from MC

Hours
Primary Crusher Operating Attachment information sent from MC
Hours
Vibrating Hammer Operating Attachment information sent from MC
Hours
Bucket Operating Hours or Attachment information sent from MC
Others
No Load Time Pressure sensor information sent from MC
T5-7-160

Communication line between MC and ICF (CAN • Check for continuity between terminals #C5 of connector ICF-C in
bus line) ICF and terminals #C4 of connector MC-C in MC. (Refer to
T5-6-57.)
• Check for continuity between terminals #C11 of connector ICF-C in
Communication line between MC and ICF (CAN ICF and terminals #C15 of connector MC-C in MC. (Refer to
bus line) T5-6-57.)
Communication line between MC and ICF (CAN • Check for shorted circuit in harness between CAN circuit in ground
bus line)
Communication line between MC and ICF (CAN circuit. (Refer to T5-6-65.)
bus line) • Check for shorted circuit in harness between CAN circuit in key
Communication line between MC and ICF (CAN signal circuit. (Refer to T5-6-68.)
bus line) • Check for shorted circuit in CAN harness. (Refer to T5-6-70.)
T5-6-57.)
ICF and terminals #C15 of connector MC-C in MC. (Refer to
T5-6-57.)
• Check for shorted circuit in harness between CAN circuit in ground
T5-7-161
Data Input Signal

Radiator Coolant Temperature Radiator coolant temperature data sent from monitor unit
Hydraulic Oil Temperature Hydraulic oil temperature data sent from MC
Intake Air Temperature Data sent from ECM
T5-7-162

bus line) ICF and terminals #B7 of connector monitor-B in monitor unit. (Re-
fer to T5-7-161.)
ICF and terminals #B6 of connector monitor-B in monitor unit. (Re-
fer to T5-7-161.)
T5-6-57.)
ICF and terminals #C15 of connector MC-C in MC. (Refer to
T5-6-57.)
(CAN bus line) ICF and terminals #18 of connector in ECM. (Refer to T5-7-160.)
ICF and terminals #37 of connector in ECM. (Refer to T5-7-160.)
T5-7-163
Discontinuity Check in CAN Harness
IMPORTANT: Before continuity check, turn the

key switch OFF.
• Between ECM and ICF

Can Harness (High Side)
Check for continuity between terminal #18 of
harness end of connector in ECM and terminal
#C5 of harness end of connector ICF-C in ICF.

Check for continuity between terminal #37 of
harness end of connector in ECM and terminal
#11 of harness end of connector ICF-C in ICF.
Connector
ECM
Connector
(Harness end)
#18 #37
T1GR-05-04-002
ICF
Connector ICF-C
(Harness end)
#C5
T1V1-05-04-002
#C11
T5-7-164
• Between Monitor Unit and ICF
CAN Harness (High Side
Check for continuity between terminal #B7 of
harness end of connector monitor-B in the moni-
tor unit and terminal #C5 of harness end of con-
nector ICF-C in ICF.
CAN Harness (Low side)

Check for continuity between terminal #B6 of
harness end of connector monitor-B in the moni-
tor unit and terminal #C11 of harness end of
connector ICF-C in ICF.
Connector
Monitor Unit
Connector Monitor-B
(Harness end)
#B7 #B6
T183-05-04-013
ICF
Connector ICF-C
(Harness end)
#C5
#C11 T1V1-05-04-002
T5-7-165
(Blank)
T5-7-166
TROUBLESHOOTING / Electrical System Inspection
PRECAUTIONS FOR INSPECTION AND
MAINTENANCE
1. Disconnect the power source.
Remove the harness from the negative terminal
side in battery first when taking wire harnesses
and connectors off for repair or replacement work.
Failure to do so can result in damage to the wire
harnesses, fuses and fusible links and, in some
cases, cause fire due to short circuiting.
2. Color coding of wire harnesses.
As for the color codes of wire harnesses in the
electrical system, refer to the table below.
In cases on the design sheet where two colors
are indicated for one wire, the left initial stands for
base color, while the right initial stands for
marking color.
Code Color Code Color

R Red W White
L Blue G Green
Or Orange Lg Light green
Y Yellow B Black
Br Brown P Pink
Gr Gray V Violet
NOTE: 1) Code BW indicates a black base wire

with white fine-line marking.
2) Initials “O” and “Or” both stand for the
color orange.
3) Wires with longitudinal stripes printed on
them are not color coded. Do not
confuse them with color coded wires.
T5-8-1
3. Precautions for connecting and disconnecting
terminal connectors.
1) When disconnecting the harnesses, grasp
Right Wrong
them by their connectors. Do not pull on the
wire itself. Release the lock first before
attempting to separate connectors, if a lock
is provided. (Refer to “Instructions for
Disconnecting Connector” on page T5-8-3.)
2) The water-resistant connectors keep water T107-07-06-001
out. If water enters them, water will not easily

drain from them. When checking the
water-resistant connectors, take extra care
not to allow water to enter the connectors. In
case water should enter the connectors,
reconnect only after the connectors are Right
thoroughly dried.
Rust
3) Before connecting terminal connectors,
check that no terminals are bent or coming Wrong
(Deformation)
off. In addition, as most connectors are
made of brass, check that no terminals are Wrong
rusting. (Separation)
4) When connecting terminal connectors T107-07-06-002
provided with a lock, insert them together
until the lock “clicks.”
5) Pull the harness near the connector in order
to check if it is correctly connected.
4. Precaution for using a circuit tester.

1) Before using a circuit tester, refer to the
Wind a Piece of Wire Tester Probe
instructions in the circuit tester manual.
Then, set the circuit tester to meet the object
to be measured, voltage range and current
polarity.
2) Before starting the connector test, always Sharpen the end of the Wire
check the connector terminal numbers, T107-07-06-003
referring to the circuit diagram.

When the connector size is very small, and
the standard probe size is too large to be
used for testing, wind a fine piece of
sharpened wire or a pin around the probe to
make the test easier.
3) When checking the connector by using a
tester, insert a tester probe from the harness
end of connector in order not to damage the
terminal inside connector.
T5-8-2
INSTRUCTIONS FOR DISCONNECTING
CONNECTORS
• Push, Unlock and Separate Type
NOTE: 1. Connectors will not be easily separated

even if the lock is pushed while being
pulled. Push the lock first before pulling the
connectors.
2. The lock is located on female side con-
nector (harness end side).
T107-04-05-002
Locations of This Type Connector

Fuel Gauge Pump Delivery Pressure Sensor Radio
Hydraulic Oil Level Switch General Relay Speaker
Horn Solenoid Valve Wiper
Cab Harness Diode Monitor Unit
Pressure Sensor Key Switch ECM
Washer Engine Control Dial ICF
• Raise Lock, Pull and Separate Type

Starter Relay 2
• Pull and Separate Type

T107-04-05-003
IMPORTANT: Before pulling and separating, re-
lease the lock of connector in the
solenoid valve by using a pair of
pincers.

Sensor
Dr. ZX
T107-04-05-004
T5-8-3
FUSE INSPECTION
Cracks in a fuse are so fine that it is very difficult or NOTE: All terminals located along the lengthwise
impossible to find by visual inspection. Use a tester in centerline of the fuse box are connected to
order to correctly inspect fuse continuity by following the power source, while terminals located
the instructions described below. away from center of the fuse box are con-
nected to loads (accessories). Therefore,
1. Turn the key switch ON. test all fuses in the same method except
When the key switch is turned ON, current from for the glow relay circuit fuse. Check the
key switch terminal M activates the battery relay glow relay circuit fuse with the key switch
so that electric power is supplied to all circuits turned to the ON position and follow the
except the glow plug relay circuit. (Refer to the procedure in step 3.
circuit diagram.)
2. Remove the fuse box cover. Set the tester.
(Measurement Range: 0 to 30 V)
3. Ground the negative probe of tester to the vehicle 10 20
frame. Touch the terminals located away from 9 19
center of the fuse box with the positive probe of
tester one at a time. When normal continuity of a 8 18
fuse is intact, the tester will indicate 20 to 25 V 7 17
(battery voltage).
6 16
5 15
4 14
3 13
2 12
1 11
M178-07-034
Fuse Fuse
Capacity Connected to Capacity Connected to
No. No.
1 20 A Work Light Relays 1 and 2 11 10 A Horn Relay
2 10 A Wiper Relay, Wiper Motor, 12 5A Radio, Cab Light
Washer Relay
3 20 A Heater (Air Conditioner Unit) 13 10 A Cigarette Lighter
4 10 A MC (Solenoid Valve Power) 14 5A Fuel Pump
5 5A Optional 1 15 10 A Auxiliary
6 10 A Optional 2 16 5A Glow Relay
7 10 A Empty 17 5A Air Conditioner Unit
8 30 A ECM Main Relay 18 5A MC, ECM, ICF, Monitor Unit
(Power ON Signal)
9 10 A Security Horn, Security Horn 19 5A Monitor Unit (Main Power)
Relay (Power), Radio (Backup)
10 5A MC, ICF (Main Power) 20 5A Optional 3
T5-8-4
FUSIBLE LINK INSPECTION Battery Relay
Inspection
1. Remove the negative cable from the battery.

2. Loosen bolt M8 holding the cable routed in front
of the fusible link box. Slide the cable out of the
way of the front cover.
3. Open the front cover of fusible link box and visu-
ally inspect the fusible link.
Fusible Link M178-07-049
Fusible Link Cover
Replacement
1. Check that the negative cable is removed from

the battery.
2. Remove bolt M8. Remove the fusible link from T178-05-06-002
the battery relay.

3. Open the upper and bottom side covers of fusible
link box. Remove screws M6 (2 used).
4. Pull out the fusible link. Replace the fusible link. Battery
Relay
5. Install screws M6 (2 used). Bolt M8
6. Install the fusible link box and the cable to the
battery relay.
7. Connect the negative cable to the battery.
Cable Screw M6
T107-04-05-008
T5-8-5
BATTERY VOLTAGE CHECK
1. Turn the key switch OFF. Check voltage between
the battery positive terminal and the vehicle frame.
Normal Voltage: 24 V
NOTE: If voltage is abnormal, recharge or replace

the battery.
2. Start the engine. Check voltage between the

battery positive terminal and the vehicle frame.
Normal Voltage: 26 to 28 V
NOTE: If voltage is abnormal, check the charging

system. V
T157-07-06-007
T5-8-6
ALTERNATOR CHECK
In general, the alternator indicator remains off when
the alternator is generating power.
If the alternator indicator comes on while the engine is
running, the alternator might be defective.
How to check the circuit
1. Turn the key switch to the ON position. Confirm

that the alternator alarm is displayed.
2. Measure voltage between teminals B and E of the

alternator. If the measured voltage is around 24 V,
the alternator circuit can be considered normal. If
the measured voltage is low, a shortage in battery Alternator T1V1-05-01-117
Monitor Unit
capacity or looseness of the wire connectors of Alarm
alternator circuit might be cause of the
malfunction. When voltage is 0 V, the wiring
between fuse box and alternator might be loose
or disconnected.
Also, the alternator cannot generate electricity if
the ground line is disconnected.
3. Next, start the engine. Measure voltage

B
generated while as the alternator rotates.
As described above, measure voltage between
terminals B and E on the alternator side. If
voltage is around 28 V, the alternator is operating
normally.
If the rated voltage is not being generated, there
is some trouble with the alternator or the regula-
tor.
E
T157-07-06-003
T5-8-7
CONTINUITY CHECK
Harness
Single-line continuity check A a
Disconnect both end connectors of the harness and
check continuity between both ends:
If the ohm-meter reading is: 0 Ω = Continuity
∞ Ω = Discontinuity
Ω
NOTE: When the one end connector is far apart

from the other, connect one end of Connect to A a
connector (A) to the machine chassis using the vehicle
a clip. Then, check continuity of the frame.
harness through the vehicle frame as
illustrated.
Connect to Ω
the vehicle
If the ohm-meter reading is: 0 Ω = Continuity frame.
∞ Ω = Discontinuity
A a
Single-line short-circuit check
Disconnect both end connectors of the harness and × Short-circuit
check continuity between one end connector of the between the
harness and
harness and the vehicle frame: the vehicle
frame.
If the ohm-meter reading is: Ω
0 Ω = Short circuit is present.
∞ Ω = No short circuit is present.
T107-07-05-003
T5-8-8
Multi-line continuity check
Disconnect both end connectors of the harness, and First short-circuit
short-circuit two terminals, (A) and (B), at one end
connector, as illustrated. Then, check continuity
A a
between terminals (a) and (b) at the other connector. B b
If the ohm-meter reading is ∞ Ω, either line (A) - (a), C c
or (B) - (b) is in discontinuity. To find out which line is
discontinued, conduct the single line continuity Second short-circuit
check on both lines individually, or, after changing
the short-circuit terminals from (A) - (B) to (A) - (C),
check continuity once more between terminals (a)
Ω
and (c).
NOTE: By conducting the multi-line continuity T107-07-05-004

check twice, it is possible to find out which
line is discontinued. With terminals (A) and
(C) short-circuited, check continuity
between terminals (a) and (c).
If the ohm-meter reading is:
0 Ω = Line (B) - (b) has discontinuity.
∞ Ω = Line (A) - (a) has discontinuity.
Multi-line short-circuit check

Disconnect both end connectors of the harness, and
check continuity between terminals (A) and (B) or
(C).
If the ohm-meter reading is:
0 Ω = Short-circuit exists between the lines.
∞ Ω = No short-circuit exists between the lines.
Short-circuit between harnesses.
A a
×
B b
C c
T107-07-05-005
T5-8-9
VOLTAGE AND CURRENT MEASURE-
MENT
Turn key switch ON so that the specified voltage (cur-
rent) is supplied to the location to be measured. Judge
if the circuit is normal by evaluating whether the
measured voltage (current) matches the specification.
24-Volt Circuit
Start checking the circuit in order up to the loca-
tion to be measured from either power source or
actuator side. Thereby, the faulty location in the
circuit will be found.
Black Probe (Negative) of Tester:
To ground to the vehicle frame
Red Probe (Positive) of Tester:
To touch the location to be measured
Engine Key Switch Location to be Measured Specification
Power Source
Circuit
Stopped OFF Between (2) and (1): One Battery 10 to 12.5 V
Stopped OFF Between (3) and (2): One Battery 10 to 12.5 V
Stopped OFF Between (3) and (1): Two Batteries 20 to 25 V
Stopped OFF Between (4) and Ground: Battery Power 20 to 25 V
Stopped OFF Between (5) and Ground: Fusible Link 20 to 25 V
Stopped OFF Between (1) and Ground: Backup Current* 6 mA
Preheat Circuit
Stopped ON or START Between (6) and Ground: Key Switch 20 to 25 V
Stopped ON or START Between (7) and Ground: Glow Plug 20 to 25 V
Charging Circuit
Fast Speed ON Between (8) and Ground: Alternator (B) / Generating 26 to 30 V
Voltage
Fast Speed ON Between (9) and Ground: Battery Relay / Generating 26 to 30 V
Voltage
Fast Speed ON Between (10) and Ground: Fuse Box / Starter Relay 2 (R) 26 to 30 V
/ Generating Voltage
Fast Speed ON Between (11) and Ground: Generating Voltage 13 to 30 V
Fast Speed ON Between (12) and Ground: Monitor Unit (C7) 13 to 30 V
Surge Voltage
Prevention Circuit
Idle Speed ON Between (8) and Ground: Alternator (B) 26 to 30 V
Idle Speed ON Between (11) and Ground: Starter Relay 2 (R) 13 to 30 V
Idle Speed ON Between (13) and Ground: Load Damp Relay 26 to 30 V
Idle Speed ON Between (9) and Ground: Battery Relay 26 to 30 V
Accessory Circuit
Stopped ON Between (14) and Ground: Auxiliary 20 to 25 V
Stopped ON Between (15) and Ground: Cigarette Lighter 20 to 25 V
Stopped ON Between (16) and Ground: Radio, Cab Light 20 to 25 V
Stopped ON Between (17) and Ground: Battery Relay 20 to 25 V
NOTE: *Before measurement, disconnect the

negative cable from the battery.
T5-8-10
Power Source Circuit
Preheat Circuit
Charging Circuit
Surge Voltage Prevention Circuit
Accessory Circuit
Key Switch
Battery
1 2 3 5 4 17 10
Starter 9
B
C
13 Load Damp
Relay
B
Fuse
S Box
E
R 16 15 14
11
12
Glow C7
B Relay
L
8
7
Glow Plug
Monitor Unit T1V1-05-06-001
T5-8-11

Starting Circuit
Started START Between (18) and Ground: Key Switch 20 to 25 V
Started START Between (19) and Ground: Battery Relay (Coil) 20 to 25 V
Started START Between (20) and Ground: Battery Relay (Switch) 20 to 25 V
Started START Between (21) and Ground: Starter (B) 20 to 25 V
Started START Between (22) and Ground: Starter (C) 20 to 25 V
Started START Between (23) and Ground: Starter Relay 2 (S) 20 to 25 V
Started START Between (24) and Ground: Starter Cut Relay 20 to 25 V
Started START Between (25) and Ground: Fuse Box 20 to 25 V
Started START Between (26) and Ground: Fuse Box 20 to 25 V
Started START Between (27) and Ground: ICF (C7) 20 to 25 V
Started START Between (28) and Ground: Monitor Unit (A7) 20 to 25 V
Started START Between (29) and Ground: MC (B16) 20 to 25 V
Started START Between (30) and Ground: ECM (1-24) 20 to 25 V
Started START Between (31) and Ground: ECM Main Relay 5V
Started START Between (32) and Ground: ECM Main Relay 20 to 25 V
NOTE: *Before measurement, disconnect the negative cable from the battery.
T5-8-12
Starting Circuit
Key Switch
Starter Cut
19 20 Relay
26
18
Battery
Battery 25
Relay
Starter
21
22 24
23
Starter R
Relay 2
27
C7
ECM Main
Relay
31
28
32
ECM MC Monitor
Unit A7
B16
1-24
30 29
T1V1-05-06-002
T5-8-13

Pilot Shut-Off Cir-
cuit
Stopped ON Between (33) and Ground: Fuse Box 20 to 25 V
Stopped ON Between (34) and Ground: Pilot Shut-Off Relay 20 to 25 V
Stopped ON Between (35) and Ground: Pilot Shut-Off Solenoid Valve 20 to 25 V
Stopped ON Between (36) and Ground: Pilot Shut-Off Relay 20 to 25 V
Stopped ON Between (37) and Ground: Security Relay 20 to 25 V
NOTE: *Before measurement, disconnect the negative cable from the battery.
T5-8-14
Pilot Shut-Off Circuit

Key Switch
Starter Cut
Relay
33
#6
Battery
Battery
Relay
Starter
Fuse
Box
Starter
Relay 2
Security
Pilot
Relay 37
Shut-Off
Lever
Pilot
Shut-Off
Relay
36
35 34
Pilot
Shut-Off Monitor
Solenoid Unit
Valve
T1V1-05-06-003
T5-8-15
5 Voltage Circuit
Power Signal or
• Voltage between terminal #1 and the vehicle Two Polarities Source Ground
frame 1 2
Disconnect the connector with the key switch OFF.
Measure voltage between terminal #1 on the
machine harness end connector and the vehicle
frame (ground).
• Key switch: ON V
• Tester black terminal (negative):
Connected to the vehicle frame (ground)
• Tester red terminal (positive):
Connected to terminal #1
T107-07-05-006
Power
Evaluation: Three Polarities
Source Signal Ground
If the measuring voltage is within 5±0.5 volts, the 1 2 3
circuit up to terminal #1 is normal.
• Voltage between terminal #1 and the ground

terminal T107-07-05-007
Disconnect the sensor connector with the key switch

OFF. Two Polarities
1 2
Measure voltage between terminal #1 on the
machine harness end connector and the ground
terminal (terminal #2 for two polarities, or terminal
#3 for three polarities).
V
• Key switch: ON
• Tester black terminal (negative):
Connected to the ground terminal
(terminal #2 or #3)
• Tester red terminal (positive):
Connected to terminal #1 T107-07-05-008
Evaluation: Three Polarities

If the measured voltage is within 5±0.5 volt, the 1 2 3
circuit up to terminal #1 or the ground terminal
(terminal #2 or #3) is normal.
T107-07-05-009
T5-8-16
CHECK BY FALSE SIGNAL
Two Polarities
Turn the key switch OFF. Disconnect the sensor con- (Hydraulic Oil Tem-
nector. Turn the key switch ON. Connect terminal #1 perature Sensor)
1 2
(power source) of machine harness end connector to
terminal #2 (signal). (Power voltage is used as a false
signal.) Check this state by using the monitor function
of Dr. ZX. When the maximum value is displayed, MC
and the circuit up to the machine harness end con-
nector are normal. If “ON” is displayed, the pressure
switch circuits are normal. Connect
IMPORTANT: Do not connect terminal #1 or #2 to

terminal #3 or to the vehicle frame
(ground) when checking a Three Polarities
T107-07-05-010
three-polarity connector.
(Pressure Sensor)
(Pump Delivery Pressure Sensor)
NOTE: Some kinds of sensors can be monitored (Pump Control Pressure Sensor) 1 2 3
by the service mode of monitor (the built-in
diagnosing system). (Refer to the TROU-
BLESHOOTING / Diagnosing Procedure
group.)
Connect
T107-07-05-011
T5-8-17
TEST HARNESS
Install a test harness between connectors. Check the
circuit condition depending on whether the test har-
ness lamp lights or extinguishes during operation.
Parts Number 4283594 (ST 7126)

Use in order to check a single-line (discontinuity
and/or voltage).
During Operation: Lamp is ON.
To Location to be Measured.
To Ground
T107-07-05-012
Parts Number 4283594 (ST 7126)
Parts Number (ST 7226)

Use in order to check the solenoid valve unit circuits.
When the corresponding control lever or switch is
operated: Lamp is ON. 4
3 50
150 50 50
1 2 2 1
T107-07-06-015
Parts Number (ST 7227) Parts Number (ST 7226)
Use in order to check the wiper circuit.
2
5 1
2 4 7
1
Parts Number (ST 7227) T178-05-06-003
T5-8-18
MEMO
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
MEMO
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
....................................................................................................................................................................
Hitachi Construction Machinery Co. Ltd Hitachi Ref. No.
Attn: Publications, Marketing & Product Support
Fax: 81-29-831-1162
SERVICE MANUAL REVISION REQUEST FORM
NAME OF COMPANY: MODEL:

PUBLICATION NO.:
YOUR NAME: (Located at the right top corner in the cover page)
DATE: PAGE NO.:

(Located at the bottom center in the page. If two or more re-
FAX: visions are requested, use the comment column)
YOUR COMMENTS / SUGGESTIONS:

Attach photo or sketch if required.
If your need more space, please use another sheet.
REPLY:
(Copy this form for usage)

THE ATTACHED DIAGRAM LIST
(The following diagrams are attached to this manual.)
1. ZAXIS200-3 CLASS/240-3 CLASS/270-3 CLASS/330-3 CLASS ELECTRICAL DIAGRAM

ZAXIS225US-3 CLASS/225USR-3 CLASS ELECTRICAL DIAGRAM
2. ZAXIS200-3 CLASS/240-3 CLASS/270-3 CLASS/330-3 CLASS CONNECTORS

ZAXIS225US-3 CLASS/225USR-3 CLASS CONNECTORS
3. ZAXIS200-3 CLASS ENGINE HARNESS 1

ZAXIS225US-3 CLASS/225USR-3 CLASS ENGINE HARNESS 1
4. ZAXIS240-3 CLASS ENGINE HARNESS 1

ZAXIS270-3 CLASS ENGINE HARNESS 1
5. ZAXIS200-3 CLASS/225US-3 CLASS/225USR-3 CLASS/240-3 CLASS/270-3 CLASS/330-3 CLASS

ENGINE HARNESS 2
ZAXIS200-3 CLASS/225US-3 CLASS/225USR-3 CLASS/240-3 CLASS/270-3 CLASS/330-3 CLASS
MONITOR UNIT HARNESS
6. ZAXIS200-3 CLASS/240-3 CLASS/270-3 CLASS/330-3 CLASS CAB HARNESS

ZAXIS225US-3 CLASS/225USR-3 CLASS CAB HARNESS
7. ZAXIS225US-3 CLASS/225USR-3 CLASS CONSOLE HARNESS
8. ZAXIS200-3 CLASS/225US-3 CLASS/225USR-3 CLASS /240-3 CLASS/270-3 CLASS

HYDRAULIC CIRCUIT DIAGRAM
9. ZAXIS240-3 CLASS/270-3 CLASS HYDRAULIC CIRCUIT DIAGRAM

(2-PIECE BOOM, BOOM HOSE RUPTURE VALVE, ARM HOSE RUPTURE VALVE,
POSITIONING HOSE RUPTURE VALVE))
ZAXIS200-3 CLASS/225US-3 CLASS/225USR-3 CLASS/240-3 CLASS/270-3 CLASS
HYDRAULIC CIRCUIT DIAGRAM
(BREAKER AND CRUSHER PIPING, 2-SPEED FLOW COMBINING PIPING)

Technical Manual: Troubleshooting

Uploaded by

Copyright:

Available Formats

Technical Manual: Troubleshooting

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Technical Manual: Troubleshooting

Uploaded by

Copyright:

Available Formats

What are the main components covered in the manual?

What are the main components covered in the manual?

What safety symbols and notations are used in the manual?

What safety symbols and notations are used in the manual?

PART NO.

PRINTED IN SINGAPORE (YS) 2006.07

TT1V1-E-01 Zaxis.p65 1 1/8/06, 15:31

• Each page has a number, located on the center

Consecutive Page Number for Each Group

• When you see these symbols on your machine or

UNDERSTAND SIGNAL WORDS

• DANGER indicates an imminently hazardous

• To avoid confusing machine protection with personal

• NOTE indicates an additional explanation for an

• If a safety sign or this manual is damaged or

• Keep your machine in proper working condition.

• Unauthorized modifications of the machine may

• Keep a first aid kit and fire extinguisher on hand.

WEAR PROTECTIVE CLOTHING

You may need:

• Avoid wearing loose clothing, jewelry, or other

• Wear a suitable hearing protective device such as

• In the walk-around inspection be sure to cover all

• When you get on and off the machine, always

ADJUST THE OPERATOR'S SEAT

• The seat should be adjusted whenever changing

with a new one.

• Before leaving the machine, be sure to first lower

FASTEN YOUR SEAT BELT

• Prior to operating the machine, thoroughly ex-

every three years regardless of its apparent con-

• Take extra care not to run over bystanders. Con-

HANDLE STARTING AIDS SAFELY

• Starting fluid is highly flammable.

• Keep all sparks and flame away when using it.

• Start the engine only when seated in the opera-

around the machine and sound the horn to alert

• If the engine must be jump started, be sure to

• Only the operator should be on the machine.

PRECAUTIONS FOR OPERATIONS

• Be sure to wear close fitting clothing and safety

ROPS: Roll-Over Protective Structure

PROVIDE SIGNALS FOR JOBS INVOLV-

CONFIRM DIRECTION OF MACHINE TO

• Before driving the machine, confirm the position

• Be sure to detour around any obstructions.

• Driving on a slope may cause the machine to slip or

• Never attempt to ascend or descend 35 degrees

pushing the levers forward moves the machine

To avoid back-over and swing accidents:

OR OTHER SIGNAL TO WARN BYSTANDERS

• Keep all persons clear from the area of operation

NEVER POSITION BUCKET OVER ANY-

• If the footing starts to collapse and if retreat is not

• Prepare machine operating area flat.

• Temperature increases will cause the ground to

NEVER UNDERCUT A HIGH BANK

• Before digging check the location of cables, gas

OPERATE WITH CAUTION