Drilling Depth Guidelines: Fluid Filled Metric U.S. Drill Rod/Core Barrel Hole Depth (Meters) Hole Depth (Feet)
Drilling Depth Guidelines: Fluid Filled Metric U.S. Drill Rod/Core Barrel Hole Depth (Meters) Hole Depth (Feet)
Drilling Depth Guidelines: Fluid Filled Metric U.S. Drill Rod/Core Barrel Hole Depth (Meters) Hole Depth (Feet)
V1 7/7/17
DRILLING DEPTH
GUIDELINES
Fluid Filled Metric U.S.
Hole Depth
Drill Rod/Core Barrel Hole Depth (meters) (feet)
BRQTM / BQTM* 3462 11358
NRQTM 1661 8730
TM
NRQ 2983 9788
TM TM
HRQ / HQ 1806 5925
HRQTM V-WallTM 2246 7368
TM
PHD /PQ 1190 3904
TM
PHD V-Wall 1592 5223
"The figures in these tables have been calculated using the pulling capacity of the
mainline hoist with a fluid filled hole and an effective rock tensile strength of 5MPa.
Actual drilling results may vary and will be affected by in-hole tools, fluid level in the
hole, subsurface and other environmental conditions, drilling techniques, and
equipment used".
* BQ capacity is shown for comparison purposes only. It is not recommended drilling
practice to drill over 2000 m BQ depth. Always verify manufacturers drill rod depth
ratings prior to use.
PRIME MOVER
Metric U.S.
HYDRAULIC
SYSTEM
Metric U.S.
Axial piston, variable
displacement, load
sensing, pressure
compensated with
Primary Pump low pressure standby.
Max flow 318 L/m 84 gpm
Maximum Pressure (factory
setting 31 MPa 4,500 psi
Axial piston, variable
displacement, load
sensing, pressure
compensated with
Secondary Pump low pressure standby.
Max flow 72 L/m 19 gpm
Maximum pressure (factory
setting 21 MPa 3,000 psi
Axial piston, variable
displacement,
pressure
Auxiliary Pump compensated.
Max flow 42 L/min 11 gpm
Maximum pressure (factory
setting) 14 MPa 2,000 psi
Hydraulic Tank Capacity 435 L 115 gal
DRILL HEAD
Metric U.S.
Resroth hydraulic
motor - variable /
Rotation Motor reversible
Ratios 1st 6.27:1
2nd 3.12:1
3rd 1.75:1
4th 1.00:1
Final Drive Straight cut gears
Ratio 2: 1
Drill Head Lubrication Force fed bearings, oil bath for gears, external sump
Drill Head Lubricating Oil
Filtration 25 micron suction oil filter
Note: Do not use multiple part lines with the main line hoist, use singe part line ONLY.
Foot clamp capacity HWT
Wireline Hoist
Chain driven - dual
Level wind ratio
Line Pull
Bare Drum 907 kg 2,000 lb
Full Drum 510 kg 1,125 lb
Line Speed
Bare Drum 160 m/min 525 ft/min
Full Drum 284 m/min 932 ft/min
Drum Capacity 3,300 m 10,827 ft
Draw Works Grp. c/w 40,000 lb main line hoist with cable, wireline hoist less cable
Hydraulic mast raising
Hydraulic mast dump
Telescopic mast assembly
** For high mobility, the mast mounted platform is kept lightweight. An optional rod
rack is available for vertical holes only, otherwise rods are stacked on the ground.
(W11) Fluid Circulation Pump
Group 254 kg 560 lb
(optional): Wet Weight
(L09) Fluid Supply Pump Group
- 145 kg 320 lb
Diesel (optional): Wet Weight
Mud Mixer Assembly 31 kg 68 lb
(optional): Wet Weight
Disclaimer: Though Boart Longyear makes certain efforts to
ensure that the requirements, measurements, specifications
and other data (“Data”) made available on our site are
reasonably accurate and reliable for their intended purposes at
the time they are posted, such data is not guaranteed and may
be subject to other terms and conditions.
LF™230
FUEL TANK
484 liter (128 gal.) fuel tank
852 liter (225 gal.) fuel tank
HEADACHE RACK
ASSEMBLY
Options Description
HYDRAULIC COOLER
PACKAGE
Options Description
COLD WEATHER
GROUP
Heating elements for the engine block and the hydrualic tank enable quick startup and
functioning in extremely cold conditions.
WIRELINE WINCH
CABLE
Full drum - 3300m (10827 ft)
Half drum - 1650m (5413 ft)
No wireline cable
DECALS AVAILABLE
IN ANY LANGUAGE
English Decals
Spanish Decals
Russian Decals
HYDRAULIC
LEVELING
JACKS/OUTRIGGERS
Four powerful, independently operated leveling jacks with a 20.5 inch stoke help reduce drill set
up time.
Each leveling jack is equipped with hydraulic locking valves and mechanical lockouts for secure
drill setup.
MOUNTING OPTION
Options Description
The ergonomically designed catwalk, railing and access stairs provide easy access to various drill
components during operation or for service and maintenance.
FLUID CIRCULATION
PUMPS
This triplex mud pump is the pump of choice for diamond drilling.
Each pump module is equipped with a relief valve, pressure gauge, suction and discharge
assemblies, lifting bar and skid base
Infinitely variable water pump speeds controlled from the operators console for optimum control
Provides support to rest the mast during transportation of the drill rig.
MUD MIXER
Having a reliable mud mixer in the field is an integral part of the drilling process, because drilling
additives require a homogenous slurry mix to make the most of their lubricating and/or
stabilizing properties
The robust, reliable and durable slurry/mud mixer has a max speed of 2300rpm at full flow
Powered directly from the drill rig’s hydraulic system, it is tough enough to operate in any
drilling environment
This Mud Tank holds 250 gallons of drilling fluid and has 4 outriggers for support.
TOOL KIT
This tool kit comes equipped with a set of handy tools for performing general maintenance on the
drill.
PAINT
Standard Boart Longyear™ Paint Colors