Physical Layer: Coaxial Cable Hybrid Cable Wireless Card Network Card

Physical Layer
This layer is the lowest layer in the OSI model. It helps in the transmission of data
between two machines that are communicating through a physical medium, which
can be optical fibres,copper wire or wireless etc. The following are the main
functions of the physical layer:
1. Hardware Specification: The details of the physical cables, network

interface cards, wireless radios, etc are a part of this layer.
Coaxial Cable Hybrid Cable Wireless Card Network Card
2. Encoding and Signalling: How are the bits encoded in the medium is also
decided by this layer. For example, on the coppar wire medium, we can use
differnet voltage levels for a certain time interval to represent '0' and '1'. We
may use +5mV for 1nsec to represent '1' and -5mV for 1nsec to represent '0'.
All the issues of modulation is dealt with in this layer. eg, we may use
Binary phase shift keying for the representation of '1' and '0' rather than
using different volatage levels if we have to transfer in RF waves.
Binary Phase Shift Keying
3. Data Transmission and Reception: The transfer of each bit of data is the

responsibility of this layer. This layer assures the transmissoin of each bit
with a high probability. The transmission of the bits is not completely
reliable as their is no error correction in this layer.
4. Topology and Network Design: The network design is the integral part of
the physical layer. Which part of the network is the router going to be
placed, where the switches will be used, where we will put the hubs, how
many machines is each switch going to handle, what server is going to be
placed where, and many such concerns are to be taken care of by the
physical layer. The variosu kinds of netopologies that we decide to use may
be ring, bus, star or a hybrid of these topologies depending on our
requirements.
Data Link Layer
This layer provides reliable transmission of a packet by using the services of the
physical layer which transmits bits over the medium in an unreliable fashion. This
layer is concerned with :
1. Framing : Breaking input data into frames (typically a few hundred bytes)
and caring about the frame boundaries and the size of each frame.
2. Acknowledgment : Sent by the receiving end to inform the source that the
frame was received without any error.
3. Sequence Numbering : To acknowledge which frame was received.
4. Error Detection : The frames may be damaged, lost or duplicated leading to
errors.The error control is on link to link basis.
5. Retransmission : The packet is retransmitted if the source fails to receive
acknowledgment.
6. Flow Control : Necessary for a fast transmitter to keep pace with a slow
receiver.
Data Link Layer
Network Layer
Its basic functions are routing and congestion control.

Routing: This deals with determining how packets will be routed (transferred)
from source to destination. It can be of three types :
 Static : Routes are based on static tables that are "wired into" the network
and are rarely changed.
 Dynamic : All packets of one application can follow different routes
depending upon the topology of the network, the shortest path and the
current network load.
 Semi-Dynamic : A route is chosen at the start of each conversation and then
all the packets of the application follow the same route.
Routing
The services provided by the network can be of two types :
 Connection less service: Each packet of an application is treated as an

independent entity. On each packet of the application the destination address
is provided and the packet is routed.
 Connection oriented service: Here, first a connection is established and
then all packets of the application follow the same route. To understand the
above concept, we can also draw an analogy from the real life. Connection
oriented service is modeled after the telephone system. All voice packets go
on the same path after the connection is established till the connection is
hung up. It acts like a tube ; the sender pushes the objects in at one end and
the receiver takes them out in the same order at the other end. Connection
less service is modeled after the postal system. Each letter carries the
destination address and is routed independent of all the others. Here, it is
possible that the letter sent first is delayed so that the second letter reaches
the destination before the first letter.
Congestion Control: A router can be connected to 4-5 networks. If all the

networks send packet at the same time with maximum rate possible then the router
may not be able to handle all the packets and may drop some/all packets. In this
context the dropping of the packets should be minimized and the source whose
packet was dropped should be informed. The control of such congestion is also a
function of the network layer. Other issues related with this layer are transmitting
time, delays, jittering.
Internetworking: Internetworks are multiple networks that are connected in such

a way that they act as one large network, connecting multiple office or department
networks. Internetworks are connected by networking hardware such as routers,
switches, and bridges.Internetworking is a solution born of three networking
problems: isolated LANs, duplication of resources, and the lack of a centralized
network management system. With connected LANs, companies no longer have to
duplicate programs or resources on each network. This in turn gives way to
managing the network from one central location instead of trying to manage each
separate LAN. We should be able to transmit any packet from one network to any
other network even if they follow different protocols or use different addressing
modes.
Inter-Networking
Network Layer does not guarantee that the packet will reach its intended
destination. There are no reliability guarantees.
Transport Layer
Its functions are :
 Multiplexing / Demultiplexing : Normally the transport layer will create

distinct network connection for each transport connection required by the
session layer. The transport layer may either create multiple network
connections (to improve throughput) or it may multiplex several transport
connections onto the same network connection (because creating and
maintaining networks may be expensive). In the latter case, demultiplexing
will be required at the receiving end. A point to note here is that
communication is always carried out between two processes and not
between two machines. This is also known as process-to-process
communication.
 Fragmentation and Re-assembly : The data accepted by the transport layer
from the session layer is split up into smaller units (fragmentation) if needed
and then passed to the network layer. Correspondingly, the data provided by
the network layer to the transport layer on the receiving side is re-
assembled.
Fragmentation Reassembly
 Types of service : The transport layer also decides the type of service that
should be provided to the session layer. The service may be perfectly
reliable, or may be reliable within certain tolerances or may not be reliable
at all. The message may or may not be received in the order in which it was
sent. The decision regarding the type of service to be provided is taken at the
time when the connection is established.
 Error Control : If reliable service is provided then error detection and error
recovery operations are also performed. It provides error control mechanism
on end to end basis.
 Flow Control : A fast host cannot keep pace with a slow one. Hence, this is
a mechanism to regulate the flow of information.
 Connection Establishment / Release : The transport layer also establishes
and releases the connection across the network. This requires some sort of
naming mechanism so that a process on one machine can indicate with
whom it wants to

Physical Layer: Coaxial Cable Hybrid Cable Wireless Card Network Card

Uploaded by

Copyright:

Available Formats

Physical Layer: Coaxial Cable Hybrid Cable Wireless Card Network Card

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Physical Layer: Coaxial Cable Hybrid Cable Wireless Card Network Card

Uploaded by

Copyright:

Available Formats

Physical Layer

1. Hardware Specification: The details of the physical cables, network

Coaxial Cable Hybrid Cable Wireless Card Network Card

3. Data Transmission and Reception: The transfer of each bit of data is the

Its basic functions are routing and congestion control.

The services provided by the network can be of two types :

 Connection less service: Each packet of an application is treated as an

Congestion Control: A router can be connected to 4-5 networks. If all the

Internetworking: Internetworks are multiple networks that are connected in such

Its functions are :

 Multiplexing / Demultiplexing : Normally the transport layer will create

You might also like