71 75 PDF

Design of Bearings
Chapter 4
L = 72
22 22
Maximum radial load = 3 = = 5.29 kN
L 3 72
GATE-5. The basic load rating of a ball bearing is [GATE-1998]

(a) The maximum static radial load that can be applied without causing any plastic
deformation of bearing components.
(b) The radial load at which 90% of the group of apparently identical bearings run
for one million revolutions before the first evidence of failure.
(c) The maximum radial load that can be applied during operation without any
plastic deformation of bearing components.
(d) A combination of radial and axial loads that can be applied without any plastic
deformation.
GATE-5 Ans. (b)
Basic Modes of Lubrication

GATE-6. Which one of the following is a criterion in the design of hydrodynamic
journal bearings? [GATE-2005]
(a) Sommerfeld number (b) rating life
(c) Specific dynamic capacity (d) Rotation factor
GATE-6 Ans. (a)Sommerfeld Number, also Known as bearing Characteristic Number,
2
zn ⎛ D ⎞
s= .⎜ ⎟
P ⎝ Cd ⎠
GATE-7. A natural feed journal bearing of diameter 50 mm and length 50 mm

operating at 20 revolution/second carries a load of 2.0 KN. The lubricant
used has a viscosity of 20 mPas. The radial clearance is 50 μm. The
Sommerfeld number for the bearing is [GATE-2007]
(a) 0.062 (b) 0.125 (c) 0.250 (d) 0.785
2
⎛ r ⎞ μN
GATE-7Ans. (b)Sommerfield number S = ⎜ ⎟ ×
⎝c⎠ P
Where, r is radius of journal
μ is viscosity of lubricant
N is number of revolution per second
P is bearing pressure on projected Area
C is radial clearance
P 2000
Therefore, P= = = 0.8N / mm2
d × l 50 × 50
2 −3
⎛ 25 ⎞ 20 × 20 × 10
S=⎜ ×
⎝ 50 × 10−3 ⎟⎠ 0.8 × 106
= 0.125
GATE-8. To restore stable operating condition in a hydrodynamic journal bearing,

when it encounters higher magnitude loads, [GATE-1997]
(a) Oil viscosity is to be decreased (b) oil viscosity is to be increased
(c) Oil viscosity index is to be increased (d) oil viscosity index is to be
decreased
GATE-8Ans. (b)
GATE-9. List l List II [GATE-1997]
(A) Automobile wheel mounting on axle 1. Magneto bearing
(B) High speed grinding spindle 2. Angular contact bearing
Design of Bearings
Chapter 4
(C) I.C. Engine connecting rod 3. Taper roller bearing
(D) Leaf spring eye mounting 4. Hydrodynamic journal bearing
5. Sintered metal bearing
6. Teflon/Nylon bush.
GATE-9Ans. (A) -3, (B) -1, (C)-4, (0)-6
GATE-10.In thick film hydrodynamic journal bearings, the coefficient of friction

(a) Increases with increases in load (b) is independent of load [GATE-1996]
(c) Decreases with increase in load (d) may increase or decrease with increase in
load
GATE-10Ans. (c)
Hydrostatic Step Bearing 464

GATE-11.Starting friction is low in [GATE-1992]
(a) Hydrostatic lubrication (b) Hydrodynamic lubrication
(c) Mixed (or semi-fluid) lubrication (d) Boundary lubrication
GATE-11Ans. (a)
Previous 20-Years IES Questions

IES-1. Consider the following statements about antifriction bearings: [IES-2008]
1. Their location influences the lateral critical speed of a rotor.
2. Roller bearings are antifriction bearings.
Which of the statements given above is/are correct?
(a) 1 only (b) 2 only
(c) Both 1 and 2 (d) Neither 1 nor 2
IES-1Ans. (c)
IES-2. A circular disc having a mass of

30 kg is mounted
asymmetrically between two
bearings A and B as shown
above in the figure. It is used as
an eccentric cam with an
eccentricity of 0.01 m. If the
shaking force on each of the
bearings is not to exceed 1500
N, the speed of rotation of the
cam should not exceed
(a) 10 rad/s (b) 100 rad/s
(c) 70.7 rad/s (d) 140 rad/s
[IES-2003]
IES-2 Ans. (b)
R max = 1500 N
Fc = 2 x R = 2 x 1500 N
mω 2 r = 2 x 1500
1/2
⎛ 2 ×1500 ⎞
or ω = ⎜ ⎟ = 100 rad / see
⎝ 30 × 0.01 ⎠
Design of Bearings
Chapter 4
Types of Rolling Contact Bearings
IES-3. In three ball bearing identified as [IES-2008]
SKF 2015, 3115 and 4215
(a) Bore is common but width is increasing
(b) Outer diameter is common but bore is increasing
(c) Width is common but outer diameter is decreasing
(d) Bore is common but outer diameter is decreasing
IES-3Ans. (a) According to ISO plan for dimension series bearings are provided with two digit
numbers. The first number indicates the width series 8, 0, 1, 2, 3, 4, 5 and 6 in order
of increasing width. The second number indicate diameter series 7, 8, 9, 0, 1, 2, 3,
and 4 in order of ascending outer diameter of bearing. Thus bearing number SKF
2015, 3115 and 4215 shows bearings belonging to different series with 75 mm bore
diameter but width is increasing.
SKF 2015, 3115 and 4215 shows width is increasing ascending outer diameter of
bearing same bore diameter 75 mm. (i.e. 15 × 5)
IES-4. Average values of effective coefficients of friction for bearings are

described below: [IES 2007]
1. Spherical ball bearing - f1 2. Cylindrical roller bearing -f2
3. Taper roller bearing - f3 4. Stable (thick film) Sliding contact
bearing - f4
Which one of the following sequences is correct?
(a) f1 < f2 < f3 < f4 (b) f1 < f2 < f4 < f3
(c) f2 < f1 < f3 < f4 (d) f1 < f4 < f2 < f3
IES-4Ans. (a)
IES-5. The rating life of a group of apparently identical ball bearings is defined
as the number of revolutions or exceeded before the first evidence of
fatigue crack by: [IES-2005]
(a) 100% of the bearings of the group (b) 95% of the bearings of the group
(c) 90% of the bearings of the group (d) 66.66% of the bearings of the group
IES-5Ans. (c)
IES-6. Match List I (Type of Bearings) with List II (Type of Load) and select the
correct answer using the code given below the Lists: [IES-2005]
List I List II
A Deep groove bearing 1. Radial load
B. Tapered roller bearing 2. Radial and axial load
C. Self aligning being 3. Mainly radial load with shaft misalignment
D. Thrust bearing 4. Mainly axial load
A B C D A B C D
(a) 1 2 3 4 (b) 3 4 1 2
Design of Bearings
Chapter 4
(c) 1 4 3 2 (d) 3 2 1 4
IES-6Ans. (a)
IES-7. Which one of the following statements is correct? [IES-2004]

Antifriction bearings are
(a) Sleeve bearings (b) gas lubricated bearings
(c) Ball and roller bearings (d) journal bearings
IES-7Ans. (c)
IES-8. The rolling element bearings are [IES-2003]

(a) Hydrostatic bearings (b) Squeeze film bearings
(c) Antifriction bearings (d) Grease lubrication bearings
IES-8Ans. (c)
IES-9. A ball-bearing is characterized by basic static capacity = 11000 N and

dynamic capacity = 18000 N. This bearing is subjected to equivalent static
load = 5500 N. The bearing loading ratio and life in million revolutions
respectively are [IES-2001]
(a) 3.27 and 52.0 (b) 3.27 and 35.0 (c) 2.00 and 10.1 (c) 1.60 and 4.1
C 18000
IES-9Ans. (b) Loading ratio = = = 3.27
P 5500
Life (million revolutions)
3 3
⎛ C ⎞ ⎛ 18000 ⎞
=⎜ ⎟ = ⎜ ⎟ = 35
⎝ P ⎠ ⎝ 5500 ⎠
IES-10. On what does the basic static capacity of a ball bearing depends?
(a) Directly proportional to number of balls in a row and diameter of ball[IES-2009]
(b) Directly proportional to square of ball diameter and inverse of number of rows of
balls
(c) Directly proportional to number of balls in a row and square of diameter of ball
(d) Inversely proportional to square of diameter of ball and directly proportional to
number of balls in a row
IES-10Ans. (c)
IES-11. Ball bearings are provided with a cage [IES-1992]

(a) To reduce friction
(b) To maintain the balls at a fixed distance apart
(c) To prevent the lubricant from flowing out
(d) To facilitate slipping of balls
IES-11Ans. (b)
IES-12. In a single row deep groove ball-bearing, cages are needed to [IES-1999]
(a) Separate the two races
(b) Separate the balls from the inner race
(c) Separate the outer race from the balls
(d) Ensure that the balls do not cluster at one point and maintain proper relative
angular positions.
IES-12Ans. (d)
IES-13. Which one of the following statements is NOT true of rolling contact
bearing? [IES-1997]
(a) The bearing characteristic number is given by ZN/p where Z is the absolute
viscosity of the lubricant, N is the shaft speed and p is the bearing pressure.
Design of Bearings
Chapter 4
(b) Inner race of a radial ball bearing has an interference fit with the shaft and
rotates along with it
(c) Outer race of the bearing has an interference fit with bearing housing and does
not rotate
(d) In some cases, the inner race is stationary and outer race rotates
IES-13Ans. (d)
IES-14. Assertion (A): It is desirable to increase the length of arc over which the oil film
has to be maintained in a journal bearing. [IES-1996]
Reason (R): The oil pressure becomes negative in the divergent part and the
partial vacuum created will cause air to leak in from the ends of bearing.
(a) Both A and R are individually true and R is the correct explanation of A
(b) Both A and R are individually true but R is not the correct explanation of A
(c) A is true but R is false
(d) A is false but R is true
IES-14Ans. (a)
IES-15. Consider the following statements about anti-friction bearings: [IES-1994]

1. They have low starting and low running friction at moderate speeds.
2. They have high resistance to shock loading.
3. They can carry both radial and thrust loads.
4. Their initial cost is high.
5. They can accommodate some amount of misalignments of shaft.
Of these statements
(a) 1, 2, 3 and 4 are correct (b) 1,3 and 4 are correct
(c) 1, 4 and 5 are correct (d) 1, 2, 3 and 5 are correct.
IES-15Ans. (a) Self aligning bearing can accommodate some amount of misalignments of
shaft.
IES-16. Removal of metal particles from the raceway of a rolling contact bearing is
a kind of failure of bearing known as [IES-1995]
(a) Pitting (b) wearing (c) spalling (d) scuffing
IES-16Ans. (a)
Load-life Relationship
IES-17. The rated life of a ball bearing varies inversely as which one of the
following? [GATE-1993; IES-2004]
(a) Load (b) (load)2 (c) (load)3 (d) (load)3.33
P
⎛d⎞
IES-17 Ans. (c) L=⎜ ⎟ , d = dynamic load capacity
⎝R⎠
R = Equivalent bearing load
p = 3 for ball bearing

10
= for roller bearing.
3
IES-18. If the load on a ball bearing is halved, its life: [IES-2005]
(a) Remains unchanged (b) Increases two times
(c) Increases four times (d) Increases eight times
3
⎛d⎞
IES-18Ans. (d) L = ⎜ ⎟ d is dynamic load carrying capacity. R is actual load applied if R
R
⎝ ⎠
halved L will increased by 23 = 8 times

71 75 PDF

Uploaded by

Copyright:

Available Formats

71 75 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

71 75 PDF

Uploaded by

Copyright:

Available Formats

Design of Bearings

GATE-5. The basic load rating of a ball bearing is [GATE-1998]

Basic Modes of Lubrication

GATE-7. A natural feed journal bearing of diameter 50 mm and length 50 mm

GATE-8. To restore stable operating condition in a hydrodynamic journal bearing,

GATE-10.In thick film hydrodynamic journal bearings, the coefficient of friction

Hydrostatic Step Bearing 464

Previous 20-Years IES Questions

IES-2. A circular disc having a mass of

IES-4. Average values of effective coefficients of friction for bearings are

IES-7. Which one of the following statements is correct? [IES-2004]

IES-8. The rolling element bearings are [IES-2003]

IES-9. A ball-bearing is characterized by basic static capacity = 11000 N and

IES-11. Ball bearings are provided with a cage [IES-1992]

IES-15. Consider the following statements about anti-friction bearings: [IES-1994]

p = 3 for ball bearing

You might also like