www.hilti.ch Profis Anchor 2.7.

5
Company: Güdel Page: 1
Specifier: gaedim Project: NCC, 6- axis gantry
Address: Fastening Point:
Phone I Fax: | Date: 08.12.2017
E-Mail:

Specifier's comments:

1 Input data
Anchor type and size: HIT-RE 500 V3 + HIT-V(5.8) M30
Effective embedment depth: hef,opti = 147 mm (hef,limit = 330 mm)
Material: 5.8
Approval No.: ETA 16/0143
Issued I Valid: 12.07.2017 | -
Proof: Design method ETAG BOND (EOTA TR 029)
Stand-off installation: eb = 0 mm (no stand-off); t = 40 mm
Baseplate: lx x ly x t = 200 mm x 350 mm x 40 mm; (Recommended plate thickness: not calculated
Profile: Square bar; (L x W x T) = 30 mm x 30 mm x 0 mm
Base material: cracked concrete, C30/37, fc,cube = 37.00 N/mm2; h = 400 mm, Temp. short/long: 40/20 °C
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: No reinforcement or Reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement

Geometry [mm] & Loading [kN, kNm]

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.ch Profis Anchor 2.7.5
Company: Güdel Page: 2
Specifier: gaedim Project: NCC, 6- axis gantry
Address: Fastening Point:
Phone I Fax: | Date: 08.12.2017
E-Mail:

2 Load case/Resulting anchor forces y

Load case: Design loads
2

Anchor reactions [kN]

Tension force: (+Tension, -Compression)
Anchor Tension force Shear force Shear force x Shear force y
1 40.000 0.000 0.000 0.000
2 40.000 0.000 0.000 0.000 x
Tension
max. concrete compressive strain: - [‰]
max. concrete compressive stress: - [N/mm2]
resulting tension force in (x/y)=(0/0): 80.000 [kN]
resulting compression force in (x/y)=(0/0): 0.000 [kN]
1

3 Tension load (EOTA TR 029, Section 5.2.2)

Load [kN] Capacity [kN] Utilisation bN [%] Status
Steel failure* 40.000 187.000 22 OK
Combined pullout-concrete cone failure** 80.000 118.665 68 OK
Concrete cone failure** 80.000 80.358 100 OK
Splitting failure** 80.000 115.728 70 OK
* most unfavourable anchor **anchor group (anchors in tension)

3.1 Steel failure

NRk,s [kN] gM,s NRd,s [kN] NSd [kN]
280.500 1.500 187.000 40.000

3.2 Combined pullout-concrete cone failure

Ap,N [mm2] A0p,N [mm2] 2
t Rk,ucr,25 [N/mm ] scr,Np [mm] ccr,Np [mm] cmin [mm]
300321 194481 13.00 441 221 9980
2 0
yc t Rk,cr [N/mm ] k y g,Np y g,Np
1.040 8.32 2.300 1.000 1.000
ec1,N [mm] y ec1,Np ec2,N [mm] y ec2,Np y s,Np y re,Np
0 1.000 0 1.000 1.000 1.000
N0Rk,p [kN] NRk,p [kN] gM,p NRd,p [kN] NSd [kN]
115.267 177.997 1.500 118.665 80.000

3.3 Concrete cone failure

Ac,N [mm2] A0c,N [mm2] ccr,N [mm] scr,N [mm]
300321 194481 221 441
ec1,N [mm] y ec1,N ec2,N [mm] y ec2,N y s,N y re,N
0 1.000 0 1.000 1.000 1.000
k1 N0Rk,c [kN] gM,c NRd,c [kN] NSd [kN]
7.200 78.057 1.500 80.358 80.000

3.4 Splitting failure

Ac,N [mm2] A0c,N [mm2] ccr,sp [mm] scr,sp [mm] y h,sp
156996 86436 147 294 1.224
ec1,N [mm] y ec1,N ec2,N [mm] y ec2,N y s,N y re,N k1
0 1.000 0 1.000 1.000 1.000 7.200
N0Rk,c [kN] gM,sp NRd,sp [kN] NSd [kN]
78.057 1.500 115.728 80.000

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.ch Profis Anchor 2.7.5
Company: Güdel Page: 3
Specifier: gaedim Project: NCC, 6- axis gantry
Address: Fastening Point:
Phone I Fax: | Date: 08.12.2017
E-Mail:

4 Shear load (EOTA TR 029, Section 5.2.3)

Load [kN] Capacity [kN] Utilisation bV [%] Status
Steel failure (without lever arm)* N/A N/A N/A N/A
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout failure* N/A N/A N/A N/A
Concrete edge failure in direction ** N/A N/A N/A N/A
* most unfavourable anchor **anchor group (relevant anchors)

5 Displacements (highest loaded anchor)

Short term loading:
NSk = 29.630 [kN] dN = 0.385 [mm]
VSk = 0.000 [kN] dV = 0.000 [mm]
dNV = 0.385 [mm]
Long term loading:
NSk = 29.630 [kN] dN = 0.385 [mm]
VSk = 0.000 [kN] dV = 0.000 [mm]
dNV = 0.385 [mm]

Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements
are valid without friction between the concrete and the baseplate! The gap due to the drilled hole and clearance hole tolerances are not
included in this calculation!

The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!

6 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.).
This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is
assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum
required anchor plate thickness with FEM to limit the stress of the anchor plate based on the assumptions explained above. The proof if the
rigid base plate assumption is valid is not carried out by PROFIS Anchor. Input data and results must be checked for agreement with the
existing conditions and for plausibility! 
• Checking the transfer of loads into the base material is required in accordance with EOTA TR 029, Section 7!
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of EOTA TR029! For larger
diameters of the clearance hole see Chapter 1.1. of EOTA TR029!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• Characteristic bond resistances depend on short- and long-term temperatures.
• Please contact Hilti to check feasibility of HIT-V rod supply.
• Edge reinforcement is not required to avoid splitting failure

Fastening meets the design criteria!

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.ch Profis Anchor 2.7.5
Company: Güdel Page: 4
Specifier: gaedim Project: NCC, 6- axis gantry
Address: Fastening Point:
Phone I Fax: | Date: 08.12.2017
E-Mail:

7 Installation data
Baseplate, steel: - Anchor type and size: HIT-RE 500 V3 + HIT-V(5.8) M30
Profile: Square bar; 30 x 30 x 0 mm Installation torque: 0.300 kNm
Hole diameter in the fixture: df = 33 mm Hole diameter in the base material: 35 mm
Plate thickness (input): 40 mm Hole depth in the base material: 147 mm
Recommended plate thickness: not calculated Minimum thickness of the base material: 217 mm
Drilling method: Hammer drilled
Cleaning: Compressed air cleaning of the drilled hole according to instructions for use is required

7.1 Recommended accessories

Drilling Cleaning Setting

• Suitable Rotary Hammer • Compressed air with required • Dispenser including cassette and mixer
• Properly sized drill bit accessories to blow from the bottom of • Torque wrench
the hole
• Proper diameter wire brush
y

100 100

55

2
175
240

x
175

1
55

100 100

Coordinates Anchor [mm]

Anchor x y c-x c+x c-y c+y
1 0 -120 - - 9980 -
2 0 120 - - 10220 -

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.ch Profis Anchor 2.7.5
Company: Güdel Page: 5
Specifier: gaedim Project: NCC, 6- axis gantry
Address: Fastening Point:
Phone I Fax: | Date: 08.12.2017
E-Mail:

8 Remarks; Your Cooperation Duties

• Any and all information and data contained in the Software concern solely the use of Hilti products and are based on the principles, formulas
and security regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be
strictly complied with by the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted
prior to using the relevant Hilti product. The results of the calculations carried out by means of the Software are based essentially on the
data you put in. Therefore, you bear the sole responsibility for the absence of errors, the completeness and the relevance of the data to be
put in by you. Moreover, you bear sole responsibility for having the results of the calculation checked and cleared by an expert, particularly
with regard to compliance with applicable norms and permits, prior to using them for your specific facility. The Software serves only as an
aid to interpret norms and permits without any guarantee as to the absence of errors, the correctness and the relevance of the results or
suitability for a specific application.
• You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for
the regular backup of programs and data and, if applicable, carry out the updates of the Software offered by Hilti on a regular basis. If you do
not use the AutoUpdate function of the Software, you must ensure that you are using the current and thus up-to-date version of the Software
in each case by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or
damaged data or programs, arising from a culpable breach of duty by you.

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan