Filmtec™ Bw30Hr-440I Element: Product Data Sheet

Product Data Sheet
FilmTec™ BW30HR-440i Element
Description FilmTec™ BW30HR-440i Element is ideal for: reverse osmosis plant

managers and operators dealing with controlled pre-treatment waters and
seeking consistency, high performance, long element life, increase
productivity, higher water quality coupled with outstanding fouling
resistance and reduced footprint installations.
With proven performance, FilmTec™ BW30HR-440i:

l Delivers high quality permeate water while minimizing CAPEX and
OPEX
l Offers increased active area with highly effective cleaning performance,
robustness and durability due to its widest cleaning pH range (1-13) and chemical
tolerance and the support of DuPont technical representatives
l Includes iLEC™ interlocking end caps, reducing system operating costs and the
risk of o-ring leaks that can cause poor water quality
Product Type Spiral-wound element with polyamide thin-film composite membrane
Typical Properties
Active Area Feed Spacer Permeate Flow Rate Typical Stabilized Salt Minimum Salt
FilmTec™ Element (ft 2) (m2) Thickness (mil) (GPD) (m3/d) Rejection (%) Rejection (%)
BW30HR-440i 440 41 28 12,650 48 99.7 99.4
1. Permeate flow and salt (NaCl) rejection based on the following standard test conditions: 2,000 ppm NaCl,
225 psi (15.5 bar), 77°F (25°C), pH 8, 15% recovery.
2. Flow rates for individual elements may vary but will be no more than ± 15%.
3. Stabilized salt rejection is generally achieved within 24-48 hours of continuous use; depending upon
feedwater characteristics and operating conditions.
4. Sales specifications may vary as design revisions take place.
5. Active area guaranteed ± 3%. Active area as stated by DuPont Water Solutions is not comparable to
nominal membrane area often stated by some manufacturers.
Page 1 of 3 Form No. 45-D01667-en, Rev. 4

January 2020
Element
Dimensions
Dimensions – inches (mm) 1 inch = 25.4 mm

A B C D
FilmTec™ Element (in.) (mm) (in.) (mm) (in.) (mm) (in.) (mm)
BW30HR-440i 40.0 1,016 40.5 1,029 7.9 201 1.125 ID 29 ID
1. Refer to FilmTec™ Design Guidelines for multiple-element systems of 8-inch elements

(Form No. 45-D01695-en).
2. Element to fit nominal 8-inch (203-mm) I.D. pressure vessel.
3. Individual elements with iLEC™ endcaps measure 40.5 inches (1,029 mm) in length (B). The net length (A)
of the elements when connected is 40.0 inches (1,016 mm).
Operating and Maximum Operating Temperature a 113°F (45°C)

Maximum Operating Pressure 600 psig (41 bar)
Cleaning Limits
Maximum Element Pressure Drop 15 psig (1.0 bar)
pH Range
Continuous Operation a 2 – 11
Short-Term Cleaning (30 min.) b 1 – 13
Maximum Feed Silt Density Index (SDI) SDI 5
Free Chlorine Tolerance c < 0.1 ppm
a. Maximum temperature for continuous operation above pH 10 is 95 °F (35 °C).

b. Refer to Cleaning Guidelines (Form No. 45-D01696-en).
c. Under certain conditions, the presence of free chlorine and other oxidizing agents will cause premature
membrane failure. Since oxidation damage is not covered under warranty, DuPont Water Solutions
recommends removing residual free chlorine by pretreatment prior to membrane exposure. Please refer to
Dechlorinating Feedwater (Form No. 45-D01569-en) for more information.
Additional Before use or storage, review these additional resources for important information:
Important l Usage Guidelines for FilmTec™ 8” Elements (Form No. 45-D01706-en)
l Start-Up Sequence (Form No. 45-D01609-en)
Information
Product DuPont has a fundamental concern for all who make, distribute, and use its products, and
Stewardship for the environment in which we live. This concern is the basis for our product stewardship
philosophy by which we assess the safety, health, and environmental information on our
products and then take appropriate steps to protect employee and public health and our
environment. The success of our product stewardship program rests with each and every
individual involved with DuPont products—from the initial concept and research, to
manufacture, use, sale, disposal, and recycle of each product.

January 2020
Customer Notice DuPont strongly encourages its customers to review both their manufacturing processes
and their applications of DuPont products from the standpoint of human health and
environmental quality to ensure that DuPont products are not used in ways for which they
are not intended or tested. DuPont personnel are available to answer your questions and to
provide reasonable technical support. DuPont product literature, including safety data
sheets, should be consulted prior to use of DuPont products. Current safety data sheets are
available from DuPont.
Please be aware of the following:

l The use of this product in and of itself does not necessarily guarantee the removal
of cysts and pathogens from water. Effective cyst and pathogen reduction is
dependent on the complete system design and on the operation and maintenance
of the system.
Regulatory Note This product may be subject to drinking water application restrictions in some countries;
please check the application status before use and sale.
Have a question? Contact us at: All information set forth herein is for informational purposes only. This information is general information and may differ from that based
on actual conditions. Customer is responsible for determining whether products and the information in this document are appropriate for
www.dupont.com/water/contact-us
Customer's use and for ensuring that Customer's workplace and disposal practices are in compliance with applicable laws and other
government enactments. The product shown in this literature may not be available for sale and/or available in all geographies where
DuPont is represented. The claims made may not have been approved for use in all countries. Please note that physical properties may
vary depending on certain conditions and while operating conditions stated in this document are intended to lengthen product lifespan
and/or improve product performance, it will ultimately depend on actual circumstances and is in no event a guarantee of achieving any
specific results. DuPont assumes no obligation or liability for the information in this document. References to “DuPont” or the “Company”
mean the DuPont legal entity selling the products to Customer unless otherwise expressly noted. NO WARRANTIES ARE GIVEN; ALL
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY EXCLUDED. No
freedom from infringement of any patent or trademark owned by DuPont or others is to be inferred.
DuPont™, the DuPont Oval Logo, and all trademarks and service marks denoted with ™, ℠ or ® are owned by affiliates of DuPont de
Nemours Inc. unless otherwise noted. © 2020 DuPont.

January 2020

Filmtec™ Bw30Hr-440I Element: Product Data Sheet

Uploaded by

Copyright:

Available Formats

Filmtec™ Bw30Hr-440I Element: Product Data Sheet

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Filmtec™ Bw30Hr-440I Element: Product Data Sheet

Uploaded by

Copyright:

Available Formats

Product Data Sheet

FilmTec™ BW30HR-440i Element

Description FilmTec™ BW30HR-440i Element is ideal for: reverse osmosis plant

With proven performance, FilmTec™ BW30HR-440i:

Product Type Spiral-wound element with polyamide thin-film composite membrane

Page 1 of 3 Form No. 45-D01667-en, Rev. 4

Dimensions – inches (mm) 1 inch = 25.4 mm

1. Refer to FilmTec™ Design Guidelines for multiple-element systems of 8-inch elements

Operating and Maximum Operating Temperature a 113°F (45°C)

a. Maximum temperature for continuous operation above pH 10 is 95 °F (35 °C).

Page 2 of 3 Form No. 45-D01667-en, Rev. 4

Please be aware of the following:

Page 3 of 3 Form No. 45-D01667-en, Rev. 4

You might also like