RTU560 product line

Communication Unit 560CMR01

Data sheet

E1 E2 CP1, CP2
10/100 MB LAN 10/100 MB LAN RS232C or RS485

Ethernet Ethernet
UART
Controller Controller

Processor bus

Serial line MPU RAM/Flash

interface ARM cortex A8 Memory

SPB I/O bus USB

Application
The 560CMR01 communication unit is one of the CMU modules Figure 1: Block diagram 560CMR01
of the RTU560 product line.

The essential tasks are: Characteristics

– Managing and controlling of the I/O modules via the inter-
face to the serial I/O bus. On the applied ARM cortex A8 controller AM3352 a real-time
– Reading Process events from the input modules. operating system is implemented. The 560CMR01 is responsi-
– Send commands to the output modules. ble for the interface management, the event handling, the time
– Communicating with control systems and local HMI sys- base and the internal data base. The controller acts as master
tems via the serial interfaces (RS232) and the Ethernet for the SPB I/O bus (serial peripheral bus). RTU560 synchronizes
10/100BaseT interfaces. itself to the time references supplied by 560RTC0x. The time in-
– Communication with Sub-RTU’s, IED’s or multimeter de- formation of the 560RTC0x is provided to the 560CMR01 on the
vices via the interfaces (RS485) and the Ethernet interfaces. backplane of the sub-rack.
– Managing the time base for the RTU560 product line station
and synchronizing the I/O modules. System relevant configuration files are stored in the non-volatile
– Handling the dialog between RTU560 product line and flash memory card (removable SD-card™) in order to guarantee
Web-Browser via the LAN interfaces. a valid system configuration after Power on Reset (PoR).

Within the RTU560 racks the board occupies . The communica- A battery buffered RTC is used to keep an exact time during
tion unit is able to handle Ethernet- and UART-character based power off state.
communication protocols.
The communication unit provides the following interfaces:
The unit has a battery buffered real time clock (RTC). – Communication Port 1 and 2 (CP1 & CP2): serial interfaces
according RS232C or RS485 with RJ45 connectors. The
communication ports can be configured independant as
SPB I/O bus interface to the front.
– Ethernet interface 1 and 2 (E1 & E2): 10/100BaseT with
RJ45 connector.
– USB 2.0 device interface for diagnosis and maintenance
purposes.
– The SPB I/O bus is directly connected to the backplane
connector.

2 | 1KGT 150 915 V004 1 - Communication Unit 560CMR01

Technical data Current consumption for power supplied via RTU560 backplane

5 V DC 500 mA
In addition to the RTU500 series general technical data, the fol-
24 V DC 3 mA
lowing applies:

Main Processing Unit MPU Signaling by LEDs

CPU ARM cortex A8, AM3352 @ 800 MHz ERR (red) ON: RTU in error state
Flashing: RTU in warning state
RAM 128 MByte
For more details see RTU500 series
Boot Flash 8 MByte Function Description

RUN (green) Communication module in operation

SD card
T Transmit data on serial communica-
Connector SD card slot (push push) tion ports CP

Type SD 2.0, class 2 R Receive data on serial communication

Capacity 4 GByte ports CP

S Ethernet communication speed:

Real time clock RTC (Backup) ON: 100 Mbit/s

OFF: 10 Mbit/s
Battery Lithium 3 V DC, CR2032
L Link up (ON) / Activity (Flashing) on
Time resolution 1 sec, 1ms with timesync
Ethernet interface E
Battery lifetime > 10 years

Free running ± 50 ppm Mechanical layout

Dimensions 160 mm x 100 mm, 3HE euro card

Serial interfaces CP1 and CP2 format

Connector RJ45 4R (20 mm) front panel

Type RS232C or RS485 Housing type Printed circuit board

RS232C: Mounting for mounting in RTU560 racks

Bit rate 200 bit/s - 38.4 kbit/s Weight 0.14 kg

Signal lines GND E2/102

TxD D1/103 Connection type

RxD D2/104 RTU560 backplane connector 48 pole type F DIN 41612

RTS S2/105
CTS M2/106
Immunity test
DTR S1.2/108
Electrostatic discharge 8 kV air / 6 kV contact (level 3)
DCD M5/109
IEC 61000-4-2 Performance criteria A
Level typical: ± 6V
Radiated Radio-Frequency Electro- 10 V/m (level 3)
RS485:
magnetic Field Performance criteria A
Bit rate 200 bit/s - 38.4 kbit/s IEC 61000-4-3

Level typical: ± 6V Electrical Fast Transient / Burst 4 kV (level X)

IEC 61000-4-4 Performance criteria A

Ethernet interface E1 and E2 Surge 2 kV (level 3)

IEC 61000-4-5 Performance criteria A
Connector RJ45
Conducted Disturbances, induced by 10 V (level 3)
Type IEEE 802.3, 10/100BaseT
Radio-Frequency Fields Performance criteria A
IEC 61000-4-6
USB interface
Damped oscillatory wave 2.5 / 1 kV (level 3)
Connector micro USB Type AB (female) IEC 61000-4-18 Performance criteria A
Type USB 2.0 device, low, full and high
speed (max. 480 MBit/s)

Cable type to PC USB Type A <-> micro USB Type B

Communication Unit 560CMR01 - 1KGT 150 915 V004 1 | 3

Environmental conditions

Nominal operating temperature range: -25°C... 70°C

Start up: -40 °C
Max. operating temperature, max. +85 °C
96h:
EN 60068-2-1, -2-2, -2-14

Relative humidity 5 ... 95 %

EN 60068-2-30 (non condensing)

Ordering information

560CMR01 R0001 1KGT036200R0001

4 | 1KGT 150 915 V004 1 - Communication Unit 560CMR01

ABB AG Note:
Power Systems Division The specifications, data, design or other information contained in this document
P.O. Box 10 03 51 (the “Brochure”) - together: the “Information” - shall only be for information pur-

68128 Mannheim, Germany poses and shall in no respect be binding. The Brochure does not claim to be ex-
haustive. Technical data in the Information are only approximate figures. We re-

www.abb.com/remote-terminal-units serve the right at any time to make technical changes or modify the contents of
this document without prior notice. The user shall be solely responsible for the
use of any application example or information described within this document.
The described examples and solutions are examples only and do not represent
any comprehensive or complete solution. The user shall determine at its sole
discretion, or as the case may be, customize, program or add value to the ABB
products including software by creating solutions for the end customer and to
assess whether and to what extent the products are suitable and need to be ad-
justed or customized.

This product is designed to be connected to and to communicate information

and data via a network interface. It is the users sole responsibility to provide and
continuously ensure a secure connection between the product and users or end
customers network or any other network (as the case may be). The user shall es-
tablish and maintain any appropriate measures (such as but not limited to the in-
stallation of firewalls, application of authentication measures, encryption of da-
ta, installation of anti-virus programs, etc) to protect the product, the network, its
system and the interface against any kind of security breaches, unauthorized ac-
cess, interference, intrusion, leakage and/or theft of data or information. ABB AG
is not liable for any damages and/or losses related to such security breaches, any
unauthorized access, interference, intrusion, leakage and/or theft of data or infor-
mation.

ABB AG shall be under no warranty whatsoever whether express or implied and

assumes no responsibility for the information contained in this document or for
any errors that may appear in this document. ABB AG's liability under or in con-
nection with this Brochure or the files included within the Brochure, irrespective
of the legal ground towards any person or entity, to which the Brochure has been
made available, in view of any damages including costs or losses shall be exclud-
ed. In particular ABB AG shall in no event be liable for any indirect, consequen-
tial or special damages, such as – but not limited to – loss of profit, loss of pro-
duction, loss of revenue, loss of data, loss of use, loss of earnings, cost of cap-
ital or cost connected with an interruption of business or operation, third party
claims. The exclusion of liability shall not apply in the case of intention or gross
negligence. The present declaration shall be governed by and construed in ac-
cordance with the laws of Switzerland under exclusion of its conflict of laws rules
and of the Vienna Convention on the International Sale of Goods (CISG).

ABB AG reserves all rights in particular copyrights and other intellectual property
rights. Any reproduction, disclosure to third parties or utilization of its contents -
in whole or in part - is not permitted without the prior written consent of ABB AG.

© Copyright ABB 2016

All rights reserved

Communication Unit 560CMR01 - 1KGT 150 915 V004 1 | 5