CCTV SYSTEM SAT PROCEDURE

00-CMC-PRO-RAS-CM-0014 Revision C

Stops, Depot, Substations: CCTV System Site Acceptance

Test Procedure

Capital Metro Project

Document Number: 00-CMC-PRO-RAS-CM-0014

Version: C
Date: 15/11/2018
Status: Issued for Construction at Risk
 CCTV SYSTEM SAT PROCEDURE
00-CMC-PRO-RAS-CM-0014 Revision C

Part (B) Test Procedure:

1. The CCTV test board is required to be placed on a fixed stand (tripod or similar) in such a way
that it covers the full visible window of the camera, which has its lens configured. Further details
on the test board usage can be found in Appendix B. Natural lighting shall be used.
2. Check the live video and confirm the necessary detail level and information can be distinguished
(kids’ faces and yellow vertical lines, next to letter C, on the 1080 HD demarcated board area).

Part (C) Purpose:

The purpose of the third part of this test is to ensure that the CCTV system provides the performance and
level of coverage required to achieve the operational objectives set in the SPR requirements and the CCTV
coverage reports. Main focus of this test is to check the coverage level and the system performance at the
most critical locations which are summarized below:
 facial and body characteristics recognition for all people entering / exiting the platforms
 facial and body characteristics identification for all people using the HPs.
 facial and body characteristics recognition for all people using the ticketing machines, inside the
platform boundaries.
 people monitoring for all people being inside the platform boundaries.
The standard used is the AS 4806.2, but with adjustment to suit High Definition CCTV systems (equivalent to
the criteria of EN 62676-4: 2015).
Part (C) Test Procedure:
The test will require two persons: The first would be looking at the laptop (*), being able to view live CCTV
image. The second person will be standing at the stop platform, at the various target locations where the
CCTV coverage is subjected to test. With reference to the CCTV coverage reports (ref. documents [12], [13],
[14] and [15]), it is preferable that the second person is standing to the furthest end of the target area. For
example, when testing the identification zone of camera CTV01 of an island stop, with regards to figure 2
below (extracted from reference document [13]), the person would be standing at position B.
(*) Note: The laptop is required to have large screen, supporting 1920 x 1080 resolution. If that is not
available, then the verification can be done by extraction of video recording and presenting them on
a large monitor supporting 1920 x 1080 resolution.

Figure 2: CCTV Coverage layout of an island stop

00-CMC-PRO-RAS-CM-0014- Stops, Depot, Substations CCTV SAT Procedure_C.doc Page 15 of 138

 CCTV SYSTEM SAT PROCEDURE
00-CMC-PRO-RAS-CM-0014 Revision C

1. Person to stand at position B.

2. Take a snapshot of the camera view with its final configuration (camera position, lens settings etc).
Snapshot of camera view is successfully captured and a printout will be also attached to the SAT
Report.
3. View the snapshot taken and compare it to the predicted camera view of the relevant CCTV
coverage report (ref. documents [12], [13], [14] and [15]). The views shall look similar.

Figure 3: CCTV camera view snapshot

4. Analyse the snapshot taken. On the printed snapshot, measure the distance of heights h (height of
the person, as presented on the screen) and H (height of the total camera view). Then, calculate the
h / H ratio. For the figure 3 example, the h / H ratio is about 0.85. Total number of vertical pixels on
the used resolution (1920x1080) is 1080. The vertical pixels that are allocated to the height of the
person are: 0.85 x 1080 = 918.
5. The height of the person shall be known. Assuming that the real person’s height (including boots
and hard hat) is 1.90m, then, the pixel density equals: 918/ 1.90m = 483 ppm (pixels per meter).

PPM
NO ZONE DESCRIPTION
(rounded)

1 Identification To enable identification of an individual or object beyond 242 / (250)

reasonable doubt and record high quality facial image.
To enable the operator to determine with a high degree of
2 Recognition certainty whether or not an individual/object shown is the same 121/ (125)
as someone they have seen before.

To enable the operator to reliably and easily determine

4 Detection 24/ (25)
whether or not any target is present.

To enable viewing of the number, direction and speed of

5 Monitoring movement across a wide area, providing presence is known to 12/ (12)
the operator.

00-CMC-PRO-RAS-CM-0014- Stops, Depot, Substations CCTV SAT Procedure_C.doc Page 16 of 138

 CCTV SYSTEM SAT PROCEDURE
00-CMC-PRO-RAS-CM-0014 Revision C

6. For each Operational Objective (Identification to Monitoring), the value of the calculated ppm shall be
greater or equal to the ones on the table above. In the given example, the 483 ppm allows for very
strong identification, which is expected, as the man is standing about one meter in front of the Help
point area and the identification zone extends about 4m beyond that position.
7. The test shall be carried out for each camera /Stop.
8. The Test Record Sheet below is to be completed.

00-CMC-PRO-RAS-CM-0014- Stops, Depot, Substations CCTV SAT Procedure_C.doc Page 17 of 138

 CCTV SYSTEM SAT PROCEDURE
00-CMC-PRO-RAS-CM-0014 Revision C

Using the snapshot, calculate the ppm for the person the calculated value is _______ ppm, which is equal or
standing inside the recognition zone near the FLRs
position.
better to 125ppm.The operational objective to
recognize facial and body characteristics is met
☐
Using the snapshot, calculate the ppm for the person the calculated value is _______ ppm, which is equal or
standing inside the recognition zone near the entry/
exit platform zone
better to 125ppm.The operational objective to
recognize facial and body characteristics is met
☐
Login to the webpage of the camera. Check the Camera IP address is in accordance to the IP plan.
Camera name and ID, the network settings and the
firmware release.
Firmware installed is the latest release. ☐
Resolution is 1920x1080 pixels at 25 frames per
From the main ‘’Live’’ tab, check the camera resolution
and fps for the live stream. second. ☐
From the main ‘’Live’’ tab, check the camera display. If Camera is targeted to the specified location and live
the camera needs adjustment, go to installer menu and
fine tune the lens Focus and Zoom adjustments.
video image is displayed clearly on the monitor. ☐
☐
Time and Date is synchronised to Master Clock.
S01_CTV05 Check Time synchronisation.
Snapshot of camera view is successfully captured.
☐
Take a snapshot of the camera view (to be attached to
Camera view shall look similar to the predicted one
the test report).
from the coverage report.
Using the snapshot, calculate the ppm for the person the calculated value is _______ ppm, which is equal or
standing inside the recognition zone near the FLRs
position.
better to 125ppm.The operational objective to
recognize facial and body characteristics is met
☐
Using the snapshot, calculate the ppm for the person the calculated value is _______ ppm, which is equal or
standing inside the recognition zone near the entry/
exit platform zone
better to 125ppm.The operational objective to
recognize facial and body characteristics is met
☐
Login to the webpage of the camera. Check the Camera IP address is in accordance to the IP plan.
Camera name and ID, the network settings and the
firmware release.
Firmware installed is the latest release. ☐
Resolution is 1920x1080 pixels at 25 frames per
From the main ‘’Live’’ tab, check the camera resolution
and fps for the live stream. second. ☐
From the main ‘’Live’’ tab, check the camera display. If Camera is targeted to the specified location and live
S01_CTV06 the camera needs adjustment, go to installer menu and
fine tune the lens Focus and Zoom adjustments.
video image is displayed clearly on the monitor. ☐
☐
Time and Date is synchronised to Master Clock.
Check Time synchronisation.
Snapshot of camera view is successfully captured.
☐
Take a snapshot of the camera view (to be attached to
Camera view shall look similar to the predicted one
the test report).
from the coverage report.

00-CMC-PRO-RAS-CM-0014- Stops, Depot, Substations CCTV SAT Procedure_C.doc Page 21 of 138

 CCTV SYSTEM SAT PROCEDURE
00-CMC-PRO-RAS-CM-0014 Revision C

From the main ‘’Live’’ tab, check the camera display. If Camera is targeted to the specified location and live
the camera needs adjustment, go to installer menu and
fine tune the lens Focus and Zoom adjustments.
video image is displayed clearly on the monitor. ☐ 
☐
Time and Date is synchronised to Master Clock.
Check Time synchronisation.
S03_CTV03
Snapshot of camera view is successfully captured.
☐
Take a snapshot of the camera view (to be attached to
Camera view shall look similar to the predicted one
the test report).
from the coverage report.
Using the snapshot, calculate the ppm for the person the calculated value is _______ ppm, which is equal or
standing inside the recognition zone near the FLRs
position.
better to 125ppm.The operational objective to
recognize facial and body characteristics is met
☐
Using the snapshot, calculate the ppm for the person the calculated value is _______ ppm, which is equal or
standing inside the recognition zone near the entry/
exit platform zone
better to 125ppm.The operational objective to
recognize facial and body characteristics is met
☐
Login to the webpage of the camera. Check the Camera IP address is in accordance to the IP plan.
Camera name and ID, the network settings and the
firmware release.
Firmware installed is the latest release. ☐
Resolution is 1920x1080 pixels at 25 frames per
From the main ‘’Live’’ tab, check the camera resolution
and fps for the live stream. second. ☐
From the main ‘’Live’’ tab, check the camera display. If Camera is targeted to the specified location and live
the camera needs adjustment, go to installer menu and
fine tune the lens Focus and Zoom adjustments.
video image is displayed clearly on the monitor. ☐ 
☐
Time and Date is synchronised to Master Clock.
S03_CTV04 Check Time synchronisation.
Snapshot of camera view is successfully captured.
☐
Take a snapshot of the camera view (to be attached to
Camera view shall look similar to the predicted one
the test report).
from the coverage report.
Using the snapshot, calculate the ppm for the person the calculated value is _______ ppm, which is equal or
standing inside the recognition zone near the FLRs
position.
better to 125ppm.The operational objective to
recognize facial and body characteristics is met
☐ 
Using the snapshot, calculate the ppm for the person the calculated value is _______ ppm, which is equal or
standing inside the recognition zone near the entry/
exit platform zone
better to 125ppm.The operational objective to
recognize facial and body characteristics is met
☐
Login to the webpage of the camera. Check the Camera IP address is in accordance to the IP plan.

S03_CTV05
Camera name and ID, the network settings and the
firmware release.
Firmware installed is the latest release. ☐
Resolution is 1920x1080 pixels at 25 frames per
From the main ‘’Live’’ tab, check the camera resolution
and fps for the live stream. second. ☐

00-CMC-PRO-RAS-CM-0014- Stops, Depot, Substations CCTV SAT Procedure_C.doc Page 29 of 138

 CCTV SYSTEM SAT PROCEDURE
00-CMC-PRO-RAS-CM-0014 Revision C

Snapshot of camera view is successfully captured.

☐
Take a snapshot of the camera view (to be attached to
Camera view shall look similar to the predicted one
the test report).
from the coverage report.
Using the snapshot, calculate the ppm for the person the calculated value is _______ ppm, which is equal or
standing inside the identification zone near the Help
Point position.
better to 250ppm.The operational objective to identify
facial and body characteristics is met
☐
Using the snapshot, calculate the ppm for the person the calculated value is _______ ppm, which is equal or
standing inside the recognition zone near the ISC
Ticket Vending Machine position.
better to 125ppm.The operational objective to
recognize facial and body characteristics is met
☐
Login to the webpage of the camera. Check the Camera IP address is in accordance to the IP plan.
Camera name and ID, the network settings and the
firmware release.
Firmware installed is the latest release. ☐
Resolution is 1920x1080 pixels at 25 frames per
From the main ‘’Live’’ tab, check the camera resolution
and fps for the live stream. second. ☐
From the main ‘’Live’’ tab, check the camera display. If Camera is targeted to the specified location and live
the camera needs adjustment, go to installer menu and
fine tune the lens Focus and Zoom adjustments.
video image is displayed clearly on the monitor. ☐
☐
Time and Date is synchronised to Master Clock.
S13_CTV02
S13_CTV08 Check Time synchronisation.
Snapshot of camera view is successfully captured.
☐
Take a snapshot of the camera view (to be attached to
Camera view shall look similar to the predicted one
the test report).
from the coverage report.
Using the snapshot, calculate the ppm for the person the calculated value is _______ ppm, which is equal or
standing inside the identification zone near the Help
Point position.
better to 250ppm.The operational objective to identify
facial and body characteristics is met
☐
Using the snapshot, calculate the ppm for the person the calculated value is _______ ppm, which is equal or
standing inside the recognition zone near the ISC
Ticket Vending Machine position.
better to 125ppm.The operational objective to
recognize facial and body characteristics is met
☐
Login to the webpage of the camera. Check the Camera IP address is in accordance to the IP plan.
Camera name and ID, the network settings and the
firmware release.
Firmware installed is the latest release. ☐
Resolution is 1920x1080 pixels at 25 frames per

S13_CTV09
From the main ‘’Live’’ tab, check the camera resolution
and fps for the live stream. second. ☐
From the main ‘’Live’’ tab, check the camera display. If Camera is targeted to the specified location and live
the camera needs adjustment, go to installer menu and
fine tune the lens Focus and Zoom adjustments.
video image is displayed clearly on the monitor. ☐ 
☐
Time and Date is synchronised to Master Clock.
Check Time synchronisation.

00-CMC-PRO-RAS-CM-0014- Stops, Depot, Substations CCTV SAT Procedure_C.doc Page 72 of 138