PERAR MODEL

EC / EB
TRUNNION
BOLTED BODY
BALL VALVES
TRUNNION BALL VALVES PERAR MODEL EC

General Description:
Perar API 6D Trunnion Ball Valves, Fire Safe according to BS 6755 Part II, API 6FA and API 607.
End connection: RF to ANSI B16.5, RTJ and BW. Bore: Reduced, Venturi and Full Port.
Body Design
Perar EC trunnion split body ball valves are made of forged steel, two pieces bolted body type side
entry construction.
Stem Design
Perar trunnion ball valves are provided with anti-blow out stem in accordance with the safety
regulation, the stem is independent from the ball and it is not subject to the side load due to the line
pressure against the ball. The stem sealing system consists in a triple barrier of ‘O’ Rings, located in
the stem bushing. Regardless rates and sizes of the valves the upper ‘O’ Ring can be replaced with
the valve installed on a pressurised line.
All valves are provided with anti-static device and self-lubrificating stem and trunnion bearings to
assure low operating torque throughout entire valve life.
Seat Design
Perar trunnion ball valves can be provided with both self-relieving seats sealing system and double
piston effect. The seat design is such that at very low pressure the sealing is assured maintaining the
seat “O” Ring in contact with the ball by pre-loaded springs, while at higher pressure the pressure
itself , acting on the differential area of the seats, helps to assure the sealing between the seats and
the ball. Valves can be double block and bleed or block and bleed according to the requirements.
Valve Operation
Perar valves are provided with Lever, Gearbox operators according to the torques requirement.
Valves can be supplied with pneumatic, electric, hydro-pneumatic, hydraulic, electro-pneumatic
actuators.

Sizes and Ratings:

ANSI CLASS
VALVE MODEL 150# 300# 600#
FULL PORT
½” THRU 4” ½” THRU 3” ½” THRU 3”
ECF
RED PORT
½” THRU 4”X3” ½” THRU 4”X3” ½” THRU 4”X3”
ECV
ANSI CLASS
VALVE MODEL 900# 1500# 2500#
FULL PORT
½” THRU 4” ½” THRU 4” ½” THRU 4”
ECF
RED PORT
½” THRU 6”X4” ½” THRU 6”X4” ½” THRU 6”X4”
ECV
API Ratings available upon request.
Standard Materials
The following bills of materials are only some sample solutions Perar has developed during its long
experience. Perar range of production covers a wider choice of materials for the different components
of the valve.
Standard Materials for ANSI Class 150#, 300#, 600#

ANSI Class 150#, 300#, 600# Carbon Steel Ball Valves

Body: ASTM A105

Ball: AISI4140+ENP
Stem: AISI 4140+ENP
Seat: A105+ENP+PTFE Insert
O’Rings: Nitrile or Viton
Gaskets: Graphite

ANSI Class 150#, 300#, 600# Low Temperature Carbon Steel Ball Valves (-46degC)

Body: ASTM A350 LF2

Ball: ASTM A350 LF2+ENP or AISI 4140+ENP
Stem: ASTM A350 LF2+ENP or AISI 4140+ENP
Seat: ASTM A350 LF2+ENP or A105+ENP + PTFE Insert
O’Rings: Nitrile or Viton
Gaskets: Graphite

ANSI Class 150#, 300#, 600# Stainless Steel Ball Valves

Body: ASTM A182 F316

Ball: ASTM A182 F316+ENP
Stem: ASTM A182 F316+ENP or 17-4-PH+ENP
Seat: ASTM A182 F316+ENP + PTFE Insert
O’Rings: Nitrile or Viton
Gaskets: Graphite

ANSI Class 150#, 300#, 600# Duplex Stainless Steel Ball Valves

Body: ASTM A182 F51

Ball: ASTM A182 F51+ENP
Stem: ASTM A182 F51+ENP
Seat: ASTM A182 F51+ENP+PTFE Insert
O’Rings: Nitrile or Viton
Gaskets: Graphite
Standard Materials for ANSI Class 900#, 1500#, 2500#

ANSI Class 900#, 1500#, 2500# Carbon Steel Ball Valves

Body: ASTM A105 or A350 LF2 (900#, 1500#), A694 F60 (2500#)
Ball: AISI4140+ENP
Stem: AISI4140+ENP
Seat: AISI4140+ENP+Nylon or Devlon Insert
O’Rings: Viton AED
Gaskets: Graphite

ANSI Class 900#, 1500#, 2500# Low Temperature Carbon Steel Ball Valves (-46degC)
Body: ASTM A350 LF2
Ball: ASTM A350 LF2+ENP or AISI 4140+ENP
Stem: ASTM A350 LF2+ENP or AISI 4140+ENP
Seat: ASTM A350 LF2+ENP or AISI 4140+ENP+Nylon or Devlon Insert
O’Rings: Viton AED
Gaskets: Graphite

ANSI Class 900#, 1500#, 2500# Stainless Steel Ball Valves

Body: ASTM A182 F316
Ball: ASTM A182 F51+ENP
Stem: ASTM A182 F51+ENP or 17-4-PH+ENP
Seat: ASTM A182 F51+ENP + Nylon or Devlon Insert
O’Rings: Viton AED
Gaskets: Graphite

ANSI Class 900#, 1500#, 2500# Duplex Stainless Steel Ball Valves
Body: ASTM A182 F51
Ball: ASTM A182 F51+ENP
Stem: ASTM A182 F51+ENP or 17-4-PH+ENP
Seat: ASTM A182 F51+ENP + Nylon or Devlon Insert
O’Rings: Viton AED
Gaskets: Graphite

Special Materials also available: A350 LF3, A350 LF6, A182 F44, A182 F55, Monel K500 or K400,
Titanium B381 Grade F2, Inconel 625, Alloy 825, Alloy 20, SANICRO-28.
Ordering Information
Floating Ball Valves Type FC, how to develop valve figure number:

TYPE BORE CLASS ENDS BODY TRIM OPTION

EC K 00 YY XXX ZZ W
F=Full 01=150# RF=Raised Face 105=A105 CS=carbon Steel L=Lever
V=Red 03=300# RJ=Ring Joint LF2=A350 LF2 LT=Low Temp. CS O=Oval
06=600# BW=Butt Weld F60= A694 F60 SS= Stainless Steel Handle
09=900# SS=Special 316=A182 F316 DS=Duplex SS G=Gearbox
15=1500# F51=A182 F51 A=Actuator
25=2500# B=Bare
00=Special Stem

Example:

Perar Model EC Trunnion Ball Valve, Bolted Body, Reduced Port, Class 300#, Raised Face End
Connection, Body Material A105, Trim Material Duplex Stainless Steel, Gear Operator:

EC-V-03-RF-105-DS-G or ECV03RF-105DS-G

For different materials, not listed in the above table, our clients should specify the bill of materials
required to a Perar representative or Perar quotation department.

Preliminary Drawing and Weight and Dimensional Table

Please refer to the attached drawings.
 Trunnion Mounted Ball Valves "EC Std" Type - FULL BORE

A Valve Weight
DN B C D D1 F H L M V Z
RF BW RTJ Pieces Wrench Valves
ANSI Class 150#
¾ 19 78 - 148 108 - - - - 370 2 12 -
1 25 78 - 148 108 - - - - 370 2 16 -
1½ 38 165 191 178 90 - 170 111 - - - - 540 2 19 -
2 51 178 216 191 110 - 190 130 - - - - 540 2 28 -
3 76 203 283 216 120 - 200 154 - - - - 370 2 35 -
4 102 229 305 241 151 - 230 - - - - - 370 2 60 -
ANSI Class 300#
¾ 19 78 - 148 108 - - - - 370 2 12 -
1 25 216 74 - 144 108 - - - - 370 2 16 -
1½ 38 191 191 - 90 - 170 111 - - - - 370 2 18 -
2 51 216 216 232 105 - 200 143 - - - - 370 2 32 -
3 76 283 283 298 135 - 240 164 - - - - 540 2 62 -
ANSI Class 600#
¾ 19 191 78 - 148 - - - - - 370 2 16 -
1 25 191 78 108 2 18
1½ 38 241 241 241 95 - 170 111 - - - - 370 2 20 -
2 51 292 292 295 110 - 190 - - - - - 370 2 42 -
3 76 356 356 359 125 - 200 - - - - - 540 2 71 -
NOTES: - Dimensions are in mm ;
- Face to face and end to end dimensions according to API 6D and ASME B16.10 ;
- Flanges in accordance with ANSI B16.5 ;
- Dimensions D1, Z with tollerance ±30 mm ;
 Trunnion Mounted Ball Valves "EC Std" Type - FULL BORE

A Valve Weight
DN B C D D1 F H L M V Z
RF BW RTJ Pieces Wrench Valves
ANSI Class 900#
1½ 38 305 305 305 80 - 160 111 - - - - 310 2 35 -
2 51 368 368 371 100 - 185 143 - - - - 370 2 64 -
3 76 381 381 384 113 205 - 164 345 399 52 300 - 2 - 82
4 102 457 457 460 143 247 - 199 308 391 84 500 - 2 - 160
ANSI Class 1500#
1½ 38 305 305 305 80 - 160 - - - - - 370 2 40 -
2 51 368 368 371 100 - 185 149 - - - - 540 2 65 73
3 76 470 470 473 113 205 - 164 345 399 52 300 - 2 - 108
4 102 546 546 549 143 247 - 199 308 391 84 500 - 2 - 188
ANSI Class 2500#
¾ - - - - - - - - - - - - 540 2 - -
1½ 35 384 384 387 120 - 170 - - - - - 540 2 56 -
2 44 451 451 454 123 - 190 - - - - - 540 2 100 -
3 64 578 578 584 115 219 - 174 297 364 65.5 400 - 2 - 226
4 89 673 673 683 186 300 - 244 408 508 105 800 - 2 - 442
NOTES: - Dimensions are in mm ;
- Face to face and end to end dimensions according to API 6D and ASME B16.10 ;
- Flanges in accordance with ANSI B16.5 ;
- Dimensions D1, Z with tollerance ±30 mm ;
 Trunnion Mounted Ball Valves "EC Std" Type - REDUCED BORE

A Valve Weight
DN B B1 C D D1 F H L M V Z
RF BW RTJ Pieces Wrench Valves
ANSI Class 150#
½x¼ 6 12 153 - - 78 - - 108 - - - - - 2 - 8
¾x½ 12 19 153 - - 78 - - 108 - - - - - 2 - 10
1x¾ 19 25 165 - - 78 - - 108 - - - - - 2 - 14
1½x1¼ 32 38 166 - - 90 - - 111 - - - - - 2 - 19
2x1½ 38 51 178 216 191 90 - 170 111 - - - - 370 2 22 -
3x2 51 76 203 283 216 110 - 190 130 - - - - 370 2 30 -
4x3 76 102 229 305 241 120 - 200 154 - - - - 540 2 41 -
ANSI Class 300#
2x1½ 38 51 216 216 232 90 - 170 111 - - - - 370 2 26 -
3x2 51 76 283 283 298 105 - 200 143 - - - - 370 2 35 -
4x3 76 102 305 305 321 135 - 240 164 - - - - 540 2 70 -
ANSI Class 600#
¾x½ 12 19 191 - - 78 - - 108 - - - - - 2 - 14
1x¾ 19 25 216 - - 78 - - 108 - - - - - 2 - 18
2x1½ 38 51 292 292 295 95 - 170 - - - - - 370 2 30 -
3x2 51 76 356 356 359 110 - 190 - - - - - 370 2 48 -
4x3 76 102 432 432 435 125 - 200 - - - - - 540 2 88 -
NOTES: - Dimensions are in mm ;
- Face to face and end to end dimensions according to API 6D and ASME B16.10 ;
- Flanges in accordance with ANSI B16.5 ;
- Dimensions D1, Z with tollerance ±30 mm ;
 Trunnion Mounted Ball Valves "EC Std" Type - REDUCED BORE

A Valve Weight
DN B B1 C D D1 F H L M V Z
RF BW RTJ Pieces Wrench Valves
ANSI Class 900#
2x1½ 38 51 368 368 371 80 - 160 111 - - - - 310 2 35 -
3x2 51 76 381 381 384 100 - 185 143 - - - - 370 3 54 -
4x3 76 102 457 457 460 113 205 - 164 345 399 52 300 - 3 - 106
6x4 102 152 610 610 613 143 247 - 199 308 391 84 500 - 2 - 245
ANSI Class 1500#
2x1½ 38 51 368 368 371 80 - 160 - - - - - 370 2 48 -
3x2 51 76 470 470 473 100 - 185 - - - - - 370 3 80 -
4x3 76 102 546 546 549 113 205 - 164 345 399 52 300 - 3 - 135
6x4 102 146 705 705 711 143 247 - 199 308 391 84 500 - 2 - 295
ANSI Class 2500#
2x1½ 35 44 451 451 454 120 194 170 149 297 364 66 400 540 3 72 90
3x2 44 64 578 578 584 123 193 190 148 297 364 66 400 540 3 120 160
4x3 64 89 673 673 683 115 219 - 174 297 364 65.5 400 - 3 - 235
6x4 89 133 914 914 927 186 300 - 244 408 508 105 800 - 3 - 600
NOTES: - Dimensions are in mm ;
- Face to face and end to end dimensions according to API 6D and ASME B16.10 ;
- Flanges in accordance with ANSI B16.5 ;
- Dimensions D1, Z with tollerance ±30 mm ;
TRUNNION BALL VALVES PERAR MODEL EB

General Description:
Perar API 6D Trunnion Ball Valves, Fire Safe according to BS 6755 Part II, API 6FA and API 607.
End connection: RF according to ANSI B16.5, RTJ and BW or any special end connection on
request. Bore: Reduced, Venturi and Full Port.
Body Design
Perar EC trunnion split body ball valves are made of forged steel, three pieces bolted body type side
entry construction.
Stem Design
Perar trunnion ball valves are provided with anti-blow out stem in accordance with the safety
regulation, the stem is independent from the ball and it is not subject to the side load due to the line
pressure against the ball. The stem sealing system consists in a triple barrier of ‘O’ Rings, located in
the stem bushing. Regardless rates and sizes of the valves the upper ‘O’ Ring can be replaced with
the valve installed on a pressurised line. All valves are provided with anti-static device and self-
lubrificating stem and trunnion bearings to assure low operating torque throughout entire valve life.
Seat Design
Perar trunnion ball valves can be provided with both self-relieving seats sealing system and double
piston effect. The seat design is such that at very low pressure the sealing is assured maintaining the
seat “O” Ring in contact with the ball by pre-loaded springs, while at higher pressure the pressure
itself , acting on the differential area of the seats, helps to assure the sealing between the seats and
the ball. Valves can be double block and bleed or block and bleed according to the requirements.
Valve Operation
Perar valves are provided with Lever, Gearbox operators according to the torques requirement. Perar
valves can also be provided with pneumatic, electric, hydro-pneumatic, hydraulic, electro-pneumatic
actuators.

Sizes and Ratings:

ANSI CLASS
VALVE MODEL 150# 300# 600#
FULL PORT
6” THRU 60” 4” THRU 60” 4” THRU 60”
EBF
RED PORT
6”X4” THRU 60” 6”X4” THRU 60” 6”X4” THRU 60”
EBV
ANSI CLASS
VALVE MODEL 900# 1500# 2500#
FULL PORT
6” AND ABOVE 6” AND ABOVE 6” AND ABOVE
EBF
RED PORT 8”X6” AND 8”X6” AND 8”X6” AND
EBV ABOVE ABOVE ABOVE
API Ratings available upon request.
Standard Materials
The following bills of materials are only some sample solutions Perar has developed during its long
experience. Perar range of production covers a wider choice of materials for the different components
of the valve.
Standard Materials for ANSI Class 150#, 300#, 600#

ANSI Class 150#, 300#, 600# Carbon Steel Ball Valves

Body: ASTM A105

Ball: ASTM A105+ENP
Stem: AISI 4140+ENP
Seat: A105+ENP+Viton O’Ring Insert
O’Rings: Nitrile or Viton
Gaskets: Graphite

ANSI Class 150#, 300#, 600# Low Temperature Carbon Steel Ball Valves (-46degC)

Body: ASTM A350 LF2

Ball: ASTM A350 LF2+ENP
Stem: ASTM A350 LF2+ENP or AISI 4140+ENP
Seat: ASTM A350 LF2+ENP+Viton O’Ring insert
O’Rings: LT Nitrile or Viton
Gaskets: Graphite

ANSI Class 150#, 300#, 600# Stainless Steel Ball Valves

Body: ASTM A182 F316

Ball: ASTM A182 F316+ENP
Stem: ASTM A182 F316+ENP or 17-4-PH+ENP
Seat: ASTM A182 F316+ENP+Viton O’Ring Insert
O’Rings: Nitrile or Viton
Gaskets: Graphite

ANSI Class 150#, 300#, 600# Duplex Stainless Steel Ball Valves

Body: ASTM A182 F51

Ball: ASTM A182 F51+ENP
Stem: ASTM A182 F51+ENP
Seat: ASTM A182 F51+ENP+Viton O’Ring Insert
O’Rings: Nitrile or Viton
Gaskets: Graphite
Standard Materials for ANSI Class 900#, 1500#, 2500#

ANSI Class 900#, 1500#, 2500# Carbon Steel Ball Valves

Body: ASTM A105 or A350 LF2 (900#, 1500#), A694 F60 (2500#)
Ball: A694 F60+ENP
Stem: AISI 4140+ENP
Seat: A694 F60+ENP + Nylon or Devlon Insert
O’Rings: Viton AED
Gaskets: Graphite

ANSI Class 900#, 1500#, 2500# Low Temperature Carbon Steel Ball Valves (-46degC)
Body: ASTM A350 LF2
Ball: ASTM A350 LF2+ENP or A694 F60+ENP
Stem: ASTM A350 LF2+ENP or A694 F60+ENP
Seat: ASTM A350 LF2+ENP or A694 F60+ENP + Nylon or Devlon Insert
O’Rings: Viton AED
Gaskets: Graphite

ANSI Class 900#, 1500#, 2500# Stainless Steel Ball Valves

Body: ASTM A182 F316
Ball: ASTM A182 F51+ENP
Stem: ASTM A182 F51+ENP or 17-4-PH+ENP
Seat: ASTM A182 F51+ENP + Nylon or Devlon Insert
O’Rings: Viton AED
Gaskets: Graphite

ANSI Class 900#, 1500#, 2500# Duplex Stainless Steel Ball Valves
Body: ASTM A182 F51
Ball: ASTM A182 F51+ENP
Stem: ASTM A182 F51+ENP or 17-4-PH+ENP
Seat: ASTM A182 F51+ENP + Nylon or Devlon Insert
O’Rings: Viton AED
Gaskets: Graphite

Special Materials also available: A350 LF3, A350 LF6, A182 F44, A182 F55, Monel K500 or K400,
Titanium B381 Grade F2, Inconel 625, Alloy 825, Alloy 20, SANICRO-28.
Ordering Information
Floating Ball Valves Type FC, how to develop valve figure number:

TYPE BORE CLASS ENDS BODY TRIM OPTION

EB K 00 YY XXX ZZ W
EB F=Full 01=150# RF=Raised Face 105=A105 CS=carbon Steel L=Lever
V=Red 03=300# RJ=Ring Joint LF2=A350 LF2 LT=Low Temp. CS O=Oval
06=600# BW=Butt Weld F60= A694 F60 SS= Stainless Steel Handle
09=900# SS=Special 316=A182 F316 DS=Duplex SS G=Gearbox
15=1500# F51=A182 F51 A=Actuator
25=2500# B=Bare
00=Special Stem

Example:

Perar Model EB Trunnion Ball Valve, Bolted Body, Reduced Port, Class 300#, Raised Face End
Connection, Body Material A105, Trim Material Duplex Stainless Steel, Gear Operator:

EB-V-03-RF-105-DS-G or EBV03RF-105DS-G

For different materials, not listed in the above table, our clients should specify the bill of materials
required to a Perar representative or Perar quotation department.

Preliminary Drawing and Weight and Dimensional Table

Please refer to the attached drawings.
 Trunnion Mounted Ball Valves "EB Std" Type - FULL BORE

A Valves Gear
DN B C D F H L M V P Q R
RF BW RTJ Wgt Wgt
ANSI Class 150#
6 152 394 457 406 166 276 235 345 399 52 300 266 300 260 160 6
8 203 457 521 470 200 318 273 297 364 65.5 400 280 370 300 245 12
10 254 533 559 546 243 362 317 297 364 65.5 400 429 430 343 415 12
12 305 610 635 622 280 398 353 297 364 65.5 400 485 460 380 630 12
14 337 686 762 699 305 456 378 440 540 105 800 540 536 405 856 43
16 387 762 838 775 348 493 415 416 516 105 500 575 560 450 1120 46
18 438 864 914 876 390 533 455 416 516 129 500 620 670 500 1642 57
20 489 914 991 927 423 568 490 548 672 129 800 680 690 570 1950 68
22 540 991 1092 1003 460 617 537 568 748 174 800 730 700 605 2480 104
24 591 1067 1143 1080 500 657 577 568 748 174 800 798 900 650 3156 104
26 635 1143 1245 1270 544 728 618 640 848 191 800 886 900 714 3700 192
28 686 1245 1346 1372 589 778 668 640 848 191 800 1000 920 720 4655 192
30 737 1295 1397 1422 608 801 681 670 908 233 800 1028 887 743 5180 270
32 781 1372 1524 1553 608 866 746 670 908 233 800 1094 1006 793 7000 270
34 832 1473 1626 1654 695 910 790 670 908 233 800 1180 1080 822 7980 270
36 876 1524 1727 1756 718 941 821 670 908 233 800 1210 1150 853 9100 270
38 927 1625 1829 - 800 978 858 670 908 233 800 1250 1190 906 11000 -
40 978 1753 1956 - 840 1008 888 670 908 233 800 1320 1250 950 12880 -
42 1022 1855 2083 - 940 1085 960 705 965 261 800 1480 1500 1055 14600 -
48 1168 2134 2388 - 1063 1335 1200 705 965 300 800 1750 1678 1140 22000 -
54 1314 2489 2489 - 1155 1425 1290 - - - - 1960 1890 1250 30180 -
60 1461 2667 2667 - 1365 1610 1475 - - - - 2170 2165 1360 47000 -
NOTES: - Dimensions are in mm.
- Face to face and end to end dimensions according to API 6D Spec.
- Flanges up to 24" (except 22") in accordance with ANSI B16.5, 22" and sizes above 24"
in accordance with MSS SP-44 and ASME B16.47 series A
- Dimensions D, H, L, M, V with tollerance ±20 mm.
 Trunnion Mounted Ball Valves "EB Std" Type - FULL BORE

A Weight Gear
DN B C D D1 F H L M V Z
RF BW RTJ Wrench Valves Wgt
ANSI Class 300#
4 102 305 305 321 140 - 216 - - - - - 740 70 -
4 102 305 305 321 140 236 - 191 297 364 66 400 - - 82

A Valves Gear
DN B C D F H L M V P Q R
RF BW RTJ Wgt Wgt
ANSI Class 300#
6 152 403 457 419 166 283 235 308 390 84 500 266 300 265 180 17
8 203 502 521 518 200 321 273 308 390 84 500 280 350 310 280 17
10 254 568 559 584 245 376 318 312 412 92.9 700 385 380 345 480 26
12 305 648 635 664 288 432 354 440 540 105 800 490 460 390 720 43
14 337 762 762 778 315 463 385 416 516 105 500 454 540 412 1082 46
16 387 838 838 854 353 496 418 416 516 129 500 585 579 460 1440 57
18 438 914 914 930 395 551 473 548 672 129 800 644 700 530 1730 68
20 489 991 991 1010 430 589 509 568 748 174 800 767 735 565 2170 104
22 540 1092 1092 1114 470 657 547 640 848 191 800 826 696 605 3000 -
24 591 1143 1143 1165 508 710 590 670 908 233 800 866 905 643 3570 270
26 635 1245 1245 1270 544 738 618 670 908 233 800 886 900 714 4640 270
28 686 1346 1346 1372 585 783 663 670 908 233 800 1010 920 720 6000 -
30 737 1397 1397 1422 630 830 705 705 965 261 800 1114 960 765 6780 350
32 781 1524 1524 1553 660 885 760 705 965 261 800 1135 1010 800 8100 -
34 832 1626 1626 1654 700 925 800 705 965 261 800 1190 1100 830 9200 -
36 876 1727 1727 1756 725 950 825 705 965 261 800 1215 1182 875 10330 -
38 927 1830 1830 - 820 983 858 705 965 261 800 1260 1205 910 12280 -
40 978 1956 1956 - 816 1023 888 705 965 300 800 1330 1260 951 13200 -
42 1022 2083 2083 - 955 1095 960 705 965 300 800 1490 1512 1060 16500 -
48 1168 2270 2270 - 1070 1335 1200 705 965 300 800 1760 1690 1140 24450 -
54 1314 2565 2565 - 1170 - 1295 - - - - 1960 1900 1255 32500 -
60 1461 2997 2997 - 1380 - 1480 - - - - 2175 2170 1370 49900 -
NOTES: - Dimensions are in mm.
- Face to face and end to end dimensions according to API 6D Spec.
- Flanges up to 24" (except 22") in accordance with ANSI B16.5, 22" and sizes above 24"
in accordance with MSS SP-44 and ASME B16.47 series A
- Dimensions D, H, L, M, V with tollerance ±20 mm.
 Trunnion Mounted Ball Valves "EB Std" Type - FULL BORE

A Weight Gear
DN B C D D1 F H L M V Z
RF BW RTJ Wrench Valves Wgt
ANSI Class 600#
4 102 432 432 435 143 - 216 - - - - - 740 123 - -
4 102 432 432 435 143 236 - 191 297 364 66 400 - - 135 12

A Valves Gear
DN B C D F H L M V P Q R
RF BW RTJ Wgt Wgt
ANSI Class 600#
6 152 559 559 562 166 297 239 312 412 92.9 700 330 310 266 260 26
8 203 660 660 664 205 355 277 440 540 105 800 350 394 291 448 43
10 254 787 787 791 250 396 318 440 540 105 800 355 385 385 705 43
12 305 838 838 841 290 437 359 416 516 105 500 480 430 425 892 46
14 337 889 889 892 323 460 382 416 516 129 500 614 258 408 1230 57
16 387 991 991 994 358 514 436 548 672 129 800 670 590 450 1700 68
18 438 1092 1092 1095 400 583 473 640 848 191 800 756 672 481 2310 192
20 489 1194 1194 1200 435 619 509 640 848 191 800 807 565 570 2690 192
22 540 1295 1295 1305 485 620 500 670 908 233 800 886 900 620 3500 -
24 591 1397 1397 1407 515 720 595 705 965 261 800 947 635 650 4400 350
26 635 1448 1448 1461 565 771 646 705 965 261 800 1026 840 700 5800 -
28 686 1549 1549 1562 590 815 680 705 965 300 800 1068 990 725 6400 -
30 737 1651 1651 1664 639 851 740 705 965 300 800 1164 1036 774 6700 -
32 781 1778 1778 1794 670 903 768 705 965 300 800 1189 1196 827 9000 -
34 832 1930 1930 1946 705 938 803 705 965 300 800 1280 1130 850 10130 -
36 876 2083 2083 2099 754 970 835 705 965 300 800 1350 1205 885 12500 -
38 927 2235 2235 - 830 1010 875 705 965 300 800 1380 1230 920 14100 -
40 978 2337 2337 - 860 1040 905 705 965 300 800 1450 1285 960 16800 -
42 1022 2437 2437 - 960 1105 970 705 965 300 800 1610 1530 1075 23900 -
48 1168 2845 2845 - 1080 - 1210 - - - - 1877 1717 1160 33000 -
54 1314 3137 3137 - 1180 - 1309 - - - - 2050 1900 1270 48800 -
60 1461 3430 3430 - 1390 - 1403 - - - - 2280 2180 1390 53000 -
NOTES: - Dimensions are in mm.
- Face to face and end to end dimensions according to API 6D Spec.
- Flanges up to 24" (except 22") in accordance with ANSI B16.5, 22" and sizes above 24"
in accordance with MSS SP-44 and ASME B16.47 series A
- Dimensions D, H, L, M, V with tollerance ±20 mm.
 Trunnion Mounted Ball Valves "EB Std" Type - FULL BORE

A Valves Gear
DN B C D F H L M V P Q R
RF BW RTJ Wgt Wgt
ANSI Class 900#
6 152 610 610 613 170 301 243 312 412 92.9 700 345 295 285 300 26
8 203 737 737 740 213 362 284 416 516 105 500 370 300 340 566 46
10 254 838 838 841 258 395 317 416 516 129 500 475 335 355 908 57
12 305 965 965 968 296 437 359 416 516 129 500 535 350 370 1190 57
14 324 1029 1029 1038 330 468 390 548 672 129 800 644 435 490 1590 68
16 375 1130 1130 1140 373 595 515 568 748 174 800 705 740 580 2150 104
18 425 1219 1219 1232 409 638 528 640 848 191 800 788 740 595 3025 192
20 473 1321 1321 1334 470 667 547 670 908 233 800 867 716 605 4256 270
22 524 1435 1435 1448 500 705 580 705 965 261 800 920 740 640 5380 -
24 572 1549 1549 1568 540 785 650 705 965 300 800 1150 1039 690 6630 500
26 619 1651 1651 1673 600 810 675 705 965 300 800 1200 1000 760 7005 500
28 667 1753 1753 1775 665 840 705 705 965 300 800 1240 1100 800 8040 -
30 714 1880 1880 1902 675 885 750 705 965 300 800 1230 1000 810 9810 500
32 762 2032 2032 2054 750 990 880 929 1334 400 800 1390 1160 885 12100 501
34 810 2159 2159 2188 780 - 868 - - - 800 1340 1370 915 14180 -
36 857 2286 2286 2315 813 - 913 - - - 800 1450 1450 948 16000 -
ANSI Class 1500#
6 146 705 705 711 205 347 269 416 516 105 500 345 378 333 495 46
8 194 832 832 841 255 377 299 416 516 129 500 465 445 390 975 57
10 241 991 991 1000 328 411 548 672 129 800 565 460 450 1680 -
12 289 1130 1130 1146 361 501 423 548 672 129 800 685 378 485 2250 68
14 318 1257 1257 1276 412 636 526 640 848 191 800 930 800 560 3180 192
16 362 1384 1384 1407 450 526 640 848 191 800 840 800 580 4220 -
18 407 1537 1537 1559 518 596 705 965 261 800 930 918 653 6130 -
20 457 1664 1664 1686 610 865 730 705 965 300 800 966 1066 745 8800 500
ANSI Class 2500#
6 133 914 914 927 265 414 336 416 516 129 500 455 380 350 1164 57
8 181 1022 1022 1038 310 456 378 548 672 129 800 560 600 410 1580 68
10 225 1270 1270 1292 440 603 525 548 672 129 800 670 630 540 3745 68
12 267 1422 1422 1445 490 672 592 568 748 174 800 730 700 605 5050 104
14 293 1651 1651 1673 538 761 641 670 908 233 800 800 765 655 6100
NOTES: - Dimensions are in mm.
- Face to face and end to end dimensions according to API 6D Spec.
- Flanges up to 24" (except 22") in accordance with ANSI B16.5, 22" and sizes above 24"
in accordance with MSS SP-44 and ASME B16.47 series A
- Dimensions D, H, L, M, V with tollerance ±20 mm.
 Trunnion Mounted Ball Valves "EB Std" Type - REDUCED BORE

A Weight Gear
DN B B1 C D D1 F H L M V Z
RF BW RTJ Wrench Valves Wgt
ANSI Class 150#
6x4 102 152 394 457 406 125 - 216 - - - - - 740 75 - -
6x4 102 152 394 457 406 - 236 - 191 297 364 66 400 - - 87 12

A Valves Gear
DN B B1 C D F H L M V P Q R
RF BW RTJ Wgt Wgt
ANSI Class 150#
8x6 152 203 457 521 470 166 276 235 345 399 52 300 266 300 260 200 6
10x8 203 254 533 559 546 200 318 273 297 364 65.5 400 280 370 300 280 12
12x10 254 305 610 635 622 243 362 317 297 364 65.5 400 429 430 343 470 12
14x12 305 337 686 762 699 280 398 353 297 364 65.5 400 485 460 380 660 12
16x12 305 387 762 838 775 280 398 353 297 364 65.5 400 485 460 380 770 12
16x14 337 387 762 838 775 305 456 378 440 540 105 800 540 536 405 910 43
18x14 337 438 864 914 876 305 456 378 440 540 105 800 540 536 405 980 43
18x16 387 438 864 914 876 348 493 415 416 516 105 500 575 560 450 1298 46
20x16 387 489 914 991 927 348 493 415 416 516 105 500 575 560 450 1330 46
20x18 438 489 914 991 927 390 533 455 416 516 129 500 620 670 500 1930 57
26x22 540 635 1143 1245 1270 460 617 537 568 748 174 800 730 700 605 2975 104
24x20 489 591 1067 1143 1080 423 568 490 548 672 129 800 680 690 570 2243 270
30x24 591 737 1295 1397 1422 500 657 577 568 748 174 800 798 900 650 4460 -
36x30 737 876 1524 1727 1756 608 801 681 670 908 233 800 1080 960 755 6635 -
NOTES: - Dimensions are in mm.
- Face to face and end to end dimensions according to API 6D Spec.
- Flanges up to 24" (except 22") in accordance with ANSI B16.5, 22" and sizes above 24"
in accordance with MSS SP-44 and ASME B16.47 series A
- Dimensions D, H, L, M, V with tollerance ±20 mm.
 Trunnion Mounted Ball Valves "EB Std" Type - REDUCED BORE

A Weight Gear
DN B B1 C D D1 F H L M V Z
RF BW RTJ Wrench Valves Wgt
ANSI Class 300#
6x4 102 152 403 457 419 140 - 216 - - - - - 740 95 - -
6x4 102 152 403 457 419 140 236 - 191 297 364 66 400 - - 107 12

A Valves Gear
DN B B1 C D F H L M V P Q R
RF BW RTJ Wgt Wgt
ANSI Class 300#
8x6 152 203 502 521 518 166 283 235 308 390 84 400 266 300 265 216 17
10x8 203 254 568 559 584 200 321 273 308 390 84 500 280 350 310 330 17
12x10 254 305 648 635 664 245 376 318 312 412 92.9 700 385 380 345 587 26
14x12 305 337 762 762 778 288 432 354 440 540 105 800 490 460 390 860 43
16x12 305 387 838 838 854 288 432 354 440 540 105 800 490 460 390 960 43
16x14 337 387 838 838 854 315 463 385 416 516 105 500 545 540 412 1200 -
18x16 387 438 914 914 930 353 496 418 416 516 129 500 585 579 460 1530 57
20x16 387 489 991 991 1010 353 496 418 416 516 129 500 585 579 460 1650 57
20x18 438 489 991 991 1010 395 551 473 548 672 129 800 644 700 530 1910 -
24x20 489 591 1143 1143 1165 430 589 509 568 748 174 800 767 735 565 2590 104
24x22 540 591 1143 1143 1165 470 657 547 640 848 191 800 826 696 605 3230 192
30x24 591 737 1397 1397 1422 508 710 590 670 908 233 800 866 905 643 4650 270
30x28 686 737 1397 1397 1422 585 783 663 670 908 233 800 1010 920 720 5975 270
36x30 737 876 1727 1727 1756 630 830 705 705 965 261 800 1114 960 765 7880 -
NOTES: - Dimensions are in mm.
- Face to face and end to end dimensions according to API 6D Spec.
- Flanges up to 24" (except 22") in accordance with ANSI B16.5, 22" and sizes above 24"
in accordance with MSS SP-44 and ASME B16.47 series A
- Dimensions D, H, L, M, V with tollerance ±20 mm.
 Trunnion Mounted Ball Valves "EB Std" Type - REDUCED BORE

A Weight Gear
DN B B1 C D D1 F H L M V Z
RF BW RTJ Wrench Valves Wgt
ANSI Class 600#
6x4 102 152 559 559 562 143 236 - 191 297 364 66 400 - - 167 12
6x4 102 152 559 559 562 143 - 216 - - - - - 740 123 - -

A Valves Gear
DN B B1 C D F H L M V P Q R
RF BW RTJ Wgt Wgt
ANSI Class 600#
8x6 152 203 660 600 664 166 297 239 312 412 92.9 700 330 310 266 305 26
10x6 152 254 787 787 791 166 297 239 312 412 92.9 700 330 310 266 390 26
10x8 203 254 787 787 791 205 355 277 440 540 105 800 350 394 291 580 43
12x8 203 305 838 838 841 205 355 277 440 540 105 800 350 394 291 664 43
12x10 254 305 838 838 841 250 396 318 440 540 105 800 355 385 385 800 43
14x12 305 337 889 889 892 290 437 359 416 516 105 500 480 430 425 1090 46
16x12 305 387 991 991 994 290 437 359 416 516 105 500 480 430 425 1170 46
16x14 337 387 991 991 994 323 460 382 416 516 129 500 614 258 408 1420 57
18x14 337 438 1092 1092 1095 323 460 382 416 516 129 500 614 258 408 1578 57
18x16 387 438 1092 1092 1095 358 514 436 548 672 129 800 670 590 450 1830 68
20x16 387 489 1194 1194 1200 358 514 436 548 672 129 800 670 590 450 2000 68
20x18 438 489 1194 1194 1200 400 583 473 640 848 191 800 756 672 481 2530 -
24x20 489 591 1397 1397 1407 435 619 509 640 848 191 800 807 565 570 3470 192
30x24 591 737 1651 1651 1664 515 720 595 705 965 261 800 947 685 650 5280 -
36x30 737 876 2083 2083 2099 639 851 716 705 965 300 800 1164 1036 774 8140 -
NOTES: - Dimensions are in mm.
- Face to face and end to end dimensions according to API 6D Spec.
- Flanges up to 24" (except 22") in accordance with ANSI B16.5, 22" and sizes above 24"
in accordance with MSS SP-44 and ASME B16.47 series A
- Dimensions D, H, L, M, V with tollerance ±20 mm.
 Trunnion Mounted Ball Valves "EB Std" Type - REDUCED BORE

A Valves Gear
DN B B1 C D F H L M V P Q R
RF BW RTJ Wgt Wgt
ANSI Class 900#
8x6 152 203 737 737 740 170 301 243 312 412 92.9 700 345 295 285 390 26
10x6 152 254 838 838 841 170 301 243 312 412 92.9 700 345 295 285 475 26
10x8 203 254 838 838 841 213 362 284 416 516 105 500 370 300 340 630 46
12x8 203 305 965 965 968 213 362 284 416 516 105 500 370 300 340 790 46
12x10 254 305 965 965 968 258 395 317 416 516 129 500 475 335 355 1045 -
16x12 305 375 1130 1130 1140 296 437 359 416 516 129 500 535 350 370 1450 57
18x16 375 425 1219 1219 1232 330 595 515 568 748 174 800 644 435 490 2550 -
20x16 375 473 1321 1321 1334 373 595 515 568 748 174 800 705 740 580 2660 -
20x18 425 473 1321 1321 1334 409 638 528 640 848 191 800 788 740 595 4250 -
24x20 473 572 1549 1549 1568 470 667 547 670 908 233 800 867 716 605 5090 270
36x30 714 857 2286 2286 2315 702 - 768 - - - 800 1290 1250 837 12160 -
ANSI Class 1500#
8x6 146 194 832 832 841 205 347 269 416 516 105 500 345 378 333 600 46
10x8 194 241 991 991 1000 255 377 299 416 516 129 500 465 445 390 1050 57
12x10 241 289 1130 1130 1146 328 411 548 672 129 800 565 460 450 1780 -
16x12 289 362 1384 1384 1407 361 501 423 548 672 129 800 685 378 485 2505 68
20x16 362 457 1664 1664 1686 450 526 640 848 191 800 840 800 580 5036 -
24x20 457 534 2049 2049 2071 610 730 705 965 300 800 966 1066 745 10050 500
ANSI Class 2500#
8x6 133 181 1022 1022 1038 265 414 336 416 516 129 500 455 380 350 1260 57
10x8 181 225 1270 1270 1292 310 456 378 548 672 129 800 560 600 410 2040 68
12x10 225 267 1422 1422 1445 440 603 525 548 672 129 800 670 630 540 4505 68
16x12 267 333 1880 1880 1902 490 672 592 568 748 174 800 730 700 605 6800 104
NOTES: - Dimensions are in mm.
- Face to face and end to end dimensions according to API 6D Spec.
- Flanges up to 24" (except 22") in accordance with ANSI B16.5, 22" and sizes above 24"
in accordance with MSS SP-44 and ASME B16.47 series A
- Dimensions D, H, L, M, V with tollerance ±20 mm.