Goodrive 200A Inver ter

Goodrive200A inverters Preface

Preface
Thanks for choosing our products.
Goodrive200A series inverters are newly-designed by our company for controlling
asynchronous AC inductance motors. Applying the most advanced speedless sensor vector
control technology, DSP control system, and our product enhances its reliability to meet the
adaptability to the environment, customized and industrialized design with more optimized
functions, more flexible application and more stable performance.
The vector control performance of Goodrive200A series inverters is as outstanding as that of
the leading sophisticated inverters on worldwide market. Its speed and torque control can be
simultaneously, comparing with the other kinds, its function of anti-trip and strong
adaptability to worse grid, temperature, humidity and dust make it meet the high
performance requirement of the customer application.
Goodrive200A series inverters apply modularized design to meet the specific demand of
customers, as well as the demand of the whole industry flexibly and follow the trend of
industrial application to the inverters on the premise of meeting general need of the market.
Powerful speed control, torque control, simple PLC, flexible input/output terminals, pulse
frequency reference, traverse control can realize various complicate high-accuracy drives
and provide integrative solution for the manufacturers of industrial devices, which
contributes a lot to the cost reducing and improves reliability.
Goodrive200A series inverters can meet the demand of environmental protection which
focuses on low noise and weakening electromagnetic interference in the application sites for
the customers.
This manual provides installation and configuration, parameters setting, fault diagnoses and
daily maintenance and relative precautions to customers. Please read this manual carefully
before the installation to ensure a proper installation and operation and high performance of
Goodrive200A series inverters.
If the product is ultimately used for military affairs or manufacture of weapon, it will be listed
on the export control formulated by Foreign Trade Law of the People's Republic of China.
Rigorous review and necessary export formalities are needed when exported.
Our company reserves the right to update the information of our products.

1
Goodrive200A inverters Contents

Contents
Preface.............................................................................................................................. 1
Contents............................................................................................................................ 2
Safety Precautions 1 ................................................................ 1
1.1 What this chapter contains .................................................................................. 1
1.2 Safety definition .................................................................................................. 1
1.3 Warning symbols ................................................................................................ 1
1.4 Safety guidelines ................................................................................................ 2
Quick Start-up 2 ..................................................... 4
2.1 What this chapter contains .................................................................................. 4
2.2 Unpacking inspection .......................................................................................... 4
2.3 Application confirmation ...................................................................................... 4
2.4 Environment ....................................................................................................... 4
2.5 Installation confirmation ...................................................................................... 5
2.6 Basic commission ............................................................................................... 5
Product Overview 3 ................................................................ 6
3.1 What this chapter contains .................................................................................. 6
3.2 Basic principles ................................................................................................... 6
3.3 Product specification ........................................................................................... 7
3.4 Name plate ......................................................................................................... 8
3.5 Type designation key .......................................................................................... 9
3.6 Rated specifications ............................................................................................ 9
3.7 Structure diagram ............................................................................................. 10
Installation Guidelines 4 ................................................................... 12
4.1 What this chapter contains ................................................................................ 12
4.2 Mechanical installation ...................................................................................... 12
4.3 Standard wiring ................................................................................................. 16
4.4 Layout protection .............................................................................................. 23
Keypad Operation Procedure 5........................................................... 25
5.1 What this chapter contains ................................................................................ 25
5.2 Keypad ............................................................................................................. 25
5.3 Keypad displaying ............................................................................................. 27
5.4 Keypad operation.............................................................................................. 27
Function Parameters 6 ........................................................... 29
6.1 What this chapter contains ................................................................................ 29
6.2 Goodrive200A general series function parameters ............................................ 29
Basic Operation Instruction 7 ................................................................ 95
7.1 What this chapter contains ................................................................................ 95
7.2 First powering on .............................................................................................. 95
7.3 Vector control.................................................................................................... 97
7.4 Torque control ................................................................................................... 98
7.5 Parameters of the motor ................................................................................... 99
7.6 Start-up and stop control ..................................................................................100
2
Goodrive200A inverters Contents
7.7 Frequency setting ............................................................................................101
7.8 Simple PLC .....................................................................................................103
7.9 Multi-step speed running ..................................................................................103
7.10 PID control .....................................................................................................104
7.11 Pulse counter .................................................................................................106
Fault Tracking 8 ..................................................... 108
8.1 What this chapter contains ...............................................................................108
8.2 Alarm and fault indications ...............................................................................108
8.3 How to reset ....................................................................................................108
8.4 Fault history .....................................................................................................108
8.5 Fault instruction and solution............................................................................108
8.6 Common fault analysis ..................................................................................... 113
8.7 Inverter system interference troubleshooting .................................................... 117
8.8 Maintenance and hardware diagnostics ........................................................... 118
Communication Protocol 9 ................................................... 123
9.1 What this chapter contains ...............................................................................123
9.2 Brief instruction to MODBUS protocol ..............................................................123
9.3 Application of the inverter .................................................................................124
9.4 RTU command code and communication data illustration .................................127
9.5 The definition of data address ..........................................................................133
9.6 Example of writing and reading ........................................................................139
Technical Data Appendix A ........................................... 143
A.1 What this chapter contains...............................................................................143
A.2 Ratings............................................................................................................143
A.3 Electric power network specification ................................................................144
A.4 Motor connection data .....................................................................................144
A.5 Applicable standards .......................................................................................145
A.6 EMC regulations ..............................................................................................145
Dimension Drawings Appendix B ............................................ 147
B.1 What this chapter contains...............................................................................147
B.2 Keypad structure .............................................................................................147
B.3 Inverter chart ...................................................................................................148
Peripheral Options and Parts Appendix C ............................................. 152
C.1 What this chapter contains ..............................................................................152
C.2 Peripheral wiring .............................................................................................152
C.3 Power supply ..................................................................................................153
C.4 Cables ............................................................................................................153
C.5 Breaker, electromagnetic contactor and leakage protection switch ...................156
C.6 Reactors .........................................................................................................158
C.7 Filters ..............................................................................................................159
C.8 Braking system ...............................................................................................160
C.9 Other optional parts .........................................................................................163
Further Information Appendix D ............................................. 164

3
Goodrive200A inverters Safety precautions
Safety Precautions 1

1.1 What this chapter contains

Please read this manual carefully and follow all safety precautions before moving, installing,
operating and servicing the inverter. If ignored, physical injury or death may occur, or
damage may occur to the devices.
If any physical injury or death or damage to the devices occurs for ignoring to the safety
precautions in the manual, our company will not be responsible for any damages and we are
not legally bound in any manner.

1.2 Safety definition

Danger: Serious physical injury or even death may occur if not follow
relevant requirements
Warning: Physical injury or damage to the devices may occur if not follow
relevant requirements
Note: Physical hurt may occur if not follow relevant requirements
Qualified People working on the device should take part in professional
electricians: electrical and safety training, receive the certification and be
familiar with all steps and requirements of installing,
commissioning, operating and maintaining the device to avoid any
emergency.

1.3 Warning symbols

Warnings caution you about conditions which can result in serious injury or death and/or
damage to the equipment, and advice on how to avoid the danger. Following warning
symbols are used in this manual:
Symbols Name Instruction Abbreviation
Serious physical injury or even
Electrical
death may occur if not follow the
Danger Danger
relative requirements
Physical injury or damage to the
General
devices may occur if not follow the
Warning danger
relative requirements
Damage to the PCBA board may
Electrostatic
occur if not follow the relative
Do not discharge
requirements
Sides of the device may become
Hot sides hot. Do not touch.
Hot sides
Physical hurt may occur if not follow
Note Note Note
the relative requirements

1
Goodrive200A inverters Safety precautions
1.4 Safety guidelines
 Only qualified electricians are allowed to operate on the inverter.
 Do not carry out any wiring and inspection or changing components when the
power supply is applied. Ensure all input power supply is disconnected
before wiring and checking and always wait for at least the time designated
on the inverter or until the DC bus voltage is less than 36V. Below is the table
of the waiting time:
Inverter model Minimum waiting time
380V 1.5kW-110kW 5 minutes
380V 132 kW-315 kW 15 minutes
380V above 350 kW 25 minutes

 Do not refit the inverter unauthorized; otherwise fire, electric shock or other
injury may occur.

 The base of the heat sink may become hot during running. Do not touch to
avoid hurt.

 The electrical parts and components inside the inverter are electrostatic. Take
measurements to avoid electrostatic discharge during relevant operation.

1.4.1 Delivery and installation

 Please install the inverter on fire-retardant material and keep the inverter
away from combustible materials.
 Connect the braking optional parts (braking resistors, braking units or
feedback units) according to the wiring diagram.
 Do not operate on the inverter if there is any damage or components loss to
the inverter.
 Do not touch the inverter with wet items or body, otherwise electric shock
may occur.
Note:
 Select appropriate moving and installing tools to ensure a safe and normal running of
the inverter and avoid physical injury or death. For physical safety, the erector should
take some mechanical protective measurements, such as wearing exposure shoes
and working uniforms.
 Ensure to avoid physical shock or vibration during delivery and installation.
 Do not carry the inverter by its cover. The cover may fall off.
 Install away from children and other public places.
 The inverter cannot meet the requirements of low voltage protection in IEC61800-5-1
if the sea level of installation site is above 2000m.
 Please use the inverter on appropriate condition (See chapter Installation
Environment).
 Don't allow screws, cables and other conductive items to fall inside the inverter.
 The leakage current of the inverter may be above 3.5mA during operation. Ground

2
Goodrive200A inverters Safety precautions
with proper techniques and ensure the grounding resistor is less than 10Ω. The
conductivity of PE grounding conductor is the same as that of the phase conductor
(with the same cross sectional area).
 R, S and T are the input terminals of the power supply, while U, V and W are the motor
terminals. Please connect the input power cables and motor cables with proper
techniques; otherwise the damage to the inverter may occur.

1.4.2 Commission and running

 Disconnect all power supplies applied to the inverter before the terminal
wiring and wait for at least the designated time after disconnecting the
power supply.
 High voltage is present inside the inverter during running. Do not carry
out any operation except for the keypad setting.
 The inverter may start up by itself when P01.21=1. Do not get close to
the inverter and motor.
 The inverter can not be used as “Emergency-stop device”.
 The inverter can not be used to break the motor suddenly. A mechanical
braking device should be provided.
Note:
 Do not switch on or off the input power supply of the inverter frequently.
 For inverters that have been stored for a long time, check and fix the capacitance and
try to run it again before utilization (see Maintenance and Hardware Fault
Diagnose).
 Cover the front board before running, otherwise electric shock may occur.

1.4.3 Maintenance and replacement of components

 Only qualified electricians are allowed to perform the maintenance,
inspection, and components replacement of the inverter.
 Disconnect all power supplies to the inverter before the terminal wiring.
Wait for at least the time designated on the inverter after disconnection.
 Take measures to avoid screws, cables and other conductive matters to
fall into the inverter during maintenance and component replacement.
Note:
 Please select proper torque to tighten screws.
 Keep the inverter, parts and components away from combustible materials during
maintenance and component replacement.
 Do not carry out any isolation and pressure test on the inverter and do not measure
the control circuit of the inverter by megameter.
 Carry out a sound anti-electrostatic protection to the inverter and its internal
components during maintenance and component replacement.

1.4.4 What to do after scrapping

 There are heavy metals in the inverter. Deal with it as industrial effluent.

3
Goodrive200A inverters Quick start-up

Quick Start-up 2

2.1 What this chapter contains

This chapter mainly describes the basic guidelines during the installation and commission
procedures on the inverter, which you may follow to install and commission the inverter
quickly.

2.2 Unpacking inspection

Check as followings after receiving products:
1. Check that there are no damage and humidification to the package. If not, please contact
with local agents or INVT offices.
2. Check the information on the type designation label on the outside of the package to
verify that the drive is of the correct type. If not, please contact with local dealers or INVT
offices.
3. Check that there are no signs of water in the package and no signs of damage or breach
to the inverter. If not, please contact with local dealers or INVT offices.
4. Check the information on the type designation label on the outside of the package to
verify that the name plate is of the correct type. If not, please contact with local dealers or
INVT offices.
5. Check to ensure the accessories (including user’s manual, control keypad and extension
card) inside the device is complete. If not, please contact with local dealers or INVT offices.

2.3 Application confirmation

Check the machine before beginning to use the inverter:
1. Check the load type to verify that there is no overload of the inverter during work and
check that whether the drive needs to modify the power degree.
2. Check that the actual current of the motor is less than the rated current of the inverter.
3. Check that the control accuracy of the load is the same of the inverter.
4. Check that the incoming supply voltage is correspondent to the rated voltage of the
inverter.

2.4 Environment
Check as followings before the actual installation and usage:
1. Check that the ambient temperature of the inverter is below 40℃ . If exceeds, derate 1%
for every additional 1℃ . Additionally, the inverter can not be used if the ambient
temperature is above 50℃.
Note: for the cabinet inverter, the ambient temperature means the air temperature inside
the cabinet.
2. Check that the ambient temperature of the inverter in actual usage is above -10℃. If not,
add heating facilities.
4
Goodrive200A inverters Quick start-up

Note: for the cabinet inverter, the ambient temperature means the air temperature inside
the cabinet.
3. Check that the altitude of the actual usage site is below 1000m. If exceeds, derate1% for
every additional 100m.
4. Check that the humidity of the actual usage site is below 90% and condensation is not
allowed. If not, add additional protection inverters.
5. Check that the actual usage site is away from direct sunlight and foreign objects can not
enter the inverter. If not, add additional protective measures.
6. Check that there is no conductive dust or flammable gas in the actual usage site. If not,
add additional protection to inverters.

2.5 Installation confirmation

Check as followings after the installation:
1. Check that the input and output cables meet the need of actual load.
2. Check that the accessories of the inverter are correctly and properly installed. The
installation cables should meet the needs of every component (including reactors, input
filters, output reactors, output filters, DC reactors, braking units and braking resistors).
3. Check that the inverter is installed on non-flammable materials and the calorific
accessories (reactors and braking resistors) are away from flammable materials.
4. Check that all control cables and power cables are run separately and the routation
complies with EMC requirement.
5. Check that all grounding systems are properly grounded according to the requirements
of the inverter.
6. Check that the free space during installation is sufficient according to the instructions in
user’s manual.
7. Check that the installation conforms to the instructions in user’s manual. The drive must
be installed in an upright position.
8. Check that the external connection terminals are tightly fastened and the torque is
appropriate.
9. Check that there are no screws, cables and other conductive items left in the inverter. If
not, get them out.

2.6 Basic commission

Complete the basic commissioning as followings before actual utilization:
1. Select the motor type, set correct motor parameters and select control mode of the
inverter according to the actual motor parameters.
2. Autotune. If possible, de-coupled from the motor load to start dynamic autotune. Or if not,
static autotune is available.
3. Adjust the ACC/DEC time according to the actual running of the load.
4. Commission the device via jogging and check that the rotation direction is as required. If
not, change the rotation direction by changing the wiring of motor.
5. Set all control parameters and then operate.
5
Goodrive200A inverters Product overview

Product Overview 3
3.1 What this chapter contains
The chapter briefly describes the operation principle, product characteristics, layout, name
plate and type designation information.
3.2 Basic principles
Goodrive200A series inverters are wall, flange and mountable devices for controlling
asynchronous AC inductance motors.
The diagram below shows the main circuit diagram of the inverter. The rectifier converts
three-phase AC voltage to DC voltage. The capacitor bank of the intermediate circuit
stabilizes the DC voltage. The converter transforms the DC voltage back to AC voltage for
the AC motor. The brake pipe connects the external braking resistor to the intermediate DC
circuit to consume the feedback energy when the voltage in the circuit exceeds its maximum
limit.

Diagram 3-1 The main circuit diagram (≤30kW)

Diagram 3-2 The main circuit diagram (≥37kW)

Note:
1. The inverter above 37kW (including 37kW) supports external DC reactor which is an
optional part. Before connecting, it is necessary to remove the copper row between P1 and
（+）.
2. The inverters (≤30kW) have standard embedded braking units and the braking resistor is
optional.
3. The inverters (≥37kW) can be installed with optional braking units and the braking unit
and resistor are optional.

6
Goodrive200A inverters Product overview

3.3 Product specification

Function Specification
AC 3PH 220V(-15%)~240V(+10%)
Input voltage (V) AC 3PH 380V(-15%)~440V(+10%)
AC 3PH 520V(-15%)~690V(+10%)
Input
Input current (A) Refer to the rated value
50Hz or 60Hz
Input frequency (Hz)
Allowed range: 47~63Hz
Output voltage (V) 0~Input voltage
Output current (A) Refer to the rated value
Output
Output power (kW) Refer to the rated value
Output frequency (Hz) 0~400Hz
Control mode SVPWM, SVC
Motor type Asynchronous motor
Speed ratio Asynchronous motor 1:100 (SVC)
Speed control
±0.2% (sensorless vector control)
accuracy
Speed fluctuation ± 0.3%(sensorless vector control)
Technical
Torque response <20ms(sensorless vector control)
control
Torque control
feature 10%(sensorless vector control)
accuracy
Starting torque Asynchronous motor: 0.5Hz/150% (SVC)
G type:
150% of rated current: 1 minute
Overload capability
180% of rated current: 10 seconds
200% of rated current: 1 second
Digital setting, analog setting, pulse frequency
setting, multi-step speed running setting, simple
Frequency setting PLC setting, PID setting, MODBUS communication
setting.
Shift between the set combination and set channel.
Running Auto voltage Keep a stable voltage automatically when the grid
control adjustment voltage transients
feature Provide over 30 fault protection functions:
Fault protection overcurrent, overvoltage, undervoltage, overheating,
phase loss and overload, etc.
Restart the rotating motor smoothly
Speed tracking Note: This function is available for the inverters of
4kW and above 4kW.
Peripheral Terminal analog input ≤ 20mV

7
Goodrive200A inverters Product overview

Function Specification
interface resolution
Terminal switch input
≤ 2ms
resolution
1 channels ( AI2) 0~10V/0~20mA and 1 channel
Analog input
(AI3) -10~10V
Analog output 2 channels (AO1, AO2) 0~10V /0~20mA
8 channels common input, the Max. frequency:
1kHz, internal impedance: 3.3kΩ;
Digital input
1 channel high speed input, the Max. frequency:
50kHz
1 channel high speed pulse output, the Max.
Digital output frequency: 50kHz;
1 channel Y terminal open collector pole output
2 channels programmable relay output
RO1A NO, RO1B NC, RO1C common terminal
Relay output
RO2A NO, RO2B NC, RO2C common terminal
Contactor capability: 3A/AC250V,1A/DC30V
Mountable method Wall, flange and floor mountable
Temperature of the
-10~50℃, derate above 40℃
running environment
Ingress protection IP20
Cooling Air-cooling
Built-in braking unit for inverters below 30kW
Others
Braking unit (including 30kW)
External braking unit for others
Built-in C3 filter: meet the degree requirement of
IEC61800-3 C3
EMC filter
External optional filter:meet the degree requirement
of IEC61800-3 C2

3.4 Name plate

Fig 3-3 Name plate

Note: This is the example of the name plate for the standard products, and CE\TUV\IP20 will
8
Goodrive200A inverters Product overview

be marked according to the actual situations.

3.5 Type designation key

The type designation contains information on the inverter. The user can find the type
designation on the type designation label attached to the inverter or the simple name plate.

Fig 3-4 Product type

Key Instructions
A GD200A : abbreviation of Goodrive200A
3-digit code: output power. “R” means the decimal point; ”011”:11kW;
B, D
“015”:15kW
C G:Constant torque load
C, E
E P:Variable torque load
Input voltage degree:
2: AC 3PH 220V(-15%)~240V(+10%)
F
4: AC 3PH 380V(-15%)~ 440V(+10%)
6: AC 3PH 520V(-15%)~690V(+10%)

3.6 Rated specifications

Constant torque Variable torque
Output Input Output Output Input Output
Model
power current current power current current
(kW) (A) (A) (kW) (A) (A)
GD200A-0R7G-4 0.75 3.4 2.5
GD200A -1R5G-4 1.5 5.0 3.7
GD200A -2R2G-4 2.2 5.8 5
GD200A -004G/5R5P-4 4 13.5 9.5 5.5 19.5 14
GD200A-5R5G/7R5P-4 5.5 19.5 14 7.5 25 18.5
GD200A -7R5G/011P-4 7.5 25 18.5 11 32 25
GD200A -011G/015P-4 11 32 25 15 40 32
GD200A -015G/018P-4 15 40 32 18.5 47 38
GD200A -018G/022P-4 18.5 47 38 22 56 45
GD200A -022G/030P-4 22 56 45 30 70 60
GD200A -030G/037P-4 30 70 60 37 80 75
GD200A -037G/045P-4 37 80 75 45 94 92
GD200A -045G/055P-4 45 94 92 55 128 115
GD200A -055G/075P-4 55 128 115 75 160 150
GD200A -075G/090P-4 75 160 150 90 190 180
GD200A -090G/110P-4 90 190 180 110 225 215
9
Goodrive200A inverters Product overview

Constant torque Variable torque

Output Input Output Output Input Output
Model
power current current power current current
(kW) (A) (A) (kW) (A) (A)
GD200A -110G/132P-4 110 225 215 132 265 260
GD200A -132G/160P-4 132 265 260 160 310 305
GD200A -160G/185P-4 160 310 305 185 345 340
GD200A -185G/200P-4 185 345 340 200 385 380
GD200A -200G/220P-4 200 385 380 220 430 425
GD200A -220G/250P-4 220 430 425 250 485 480
GD200A -250G/280P-4 250 485 480 280 545 530
GD200A -280G/315P-4 280 545 530 315 610 600
GD200A -315G/350P-4 315 610 600 350 625 650
GD200A -350G/400P-4 350 625 650 400 715 720
GD200A -400G-4 400 715 720
GD200A -500G-4 500 890 860
Note:
1. The input current of 1.5~315kW inverters is measured when the input voltage is 380V and
no DC reactor and input/output reactor.
2. The input current of 350~500kW inverters is measured when the input voltage is 380V
and the circuit is with input reactor.
3. The rated output current is defined as the output current when the output voltage is 380V.
4. In the allowable voltage range, the output power and current can not exceed the rated
output power and current in any situation.

3.7 Structure diagram

Below is the layout figure of the inverter (take the inverter of 30kW as the example).

1 6
7

2 8

9
3 10
11

12
13

10
Goodrive200A inverters Product overview

Fig 3-5 Product structure diagram

Serial
Name Illustration
No.
1 Keypad port Connect the keypad
2 Upper cover Protect the internal parts and components
See Keypad Operation Procedure for detailed
3 Keypad
information
See Maintenance and Hardware Fault Diagnose for
4 Cooling fan
detailed information
5 Wires port Connect to the control board and the drive board
6 Name plate See Product Overview for detailed information
Optional part. The side cover will increase the
protective degree of the inverter. The internal
7 Side cover
temperature of the inverter will increase, too, so it is
necessary to derate the inverter at the same time
8 Control terminals See Electric Installation for detailed information
9 Main circuit terminals See Electric Installation for detailed information
10 Main circuit cable entry Fix the main circuit cable
11 POWER light Power indicator
12 Simple name plate See Product Overview for detailed information
13 Lower cover Protect the internal parts and components

11
Goodrive200A inverters Installation guidelines

Installation Guidelines 4

4.1 What this chapter contains

The chapter describes the mechanical installation and electric installation.

 Only qualified electricians are allowed to carry out what described in this
chapter. Please operate as the instructions in Safety Precautions. Ignoring
these may cause physical injury or death or damage to the devices.
 Ensure the power supply of the inverter is disconnected during the operation.
Wait for at least the time designated until the POWER indicator is off after the
disconnection if the power supply is applied. It is recommended to use the
multimeter to monitor that the DC bus voltage of the drive is under 36V.
 The installation and design of the inverter should be complied with the
requirement of the local laws and regulations in the installation site. If the
installation infringes the requirement, our company will exempt from any
responsibility. Additionally, if users do not comply with the suggestion, some
damage beyond the assured maintenance range may occur.

4.2 Mechanical installation

4.2.1 Installation environment
The installation environment is important for a full performance and long-term stable
functions of the inverter. Check the installation environment as followings:
Environment Conditions
Installation site Indoor
-10~+50℃
If the ambient temperature of the inverter is above 40℃ , derate 1%
for every additional 1℃ .
It is not recommended to use the inverter if the ambient
temperature is above 50℃ .
In order to improve the reliability of the device, do not use the
Environment inverter if the ambient temperature changes frequently.
temperature Please provide cooling fan or air conditioner to control the internal
ambient temperature below the required one if the inverter is used
in a close space such as in the control cabinet.
When the temperature is too low, if the inverter needs to restart to
run after a long stop, it is necessary to provide an external heating
device to increase the internal temperature, otherwise damage to
the devices may occur.
RH≤90%
Humidity
No condensation is allowed.

12
Goodrive200A inverters Installation guidelines

Environment Conditions
The maximum relative humility should be equal to or less than
60% in corrosive air.
Storage
-30~+60℃
temperature
The installation site of the inverter should:
keep away from the electromagnetic radiation source;
keep away from contaminative air, such as corrosive gas, oil mist
Running and flammable gas;
environment ensure foreign objects, such as metal power, dust, oil, water can
condition not enter into the inverter(do not install the inverter on the
flammable materials such as wood);
keep away from direct sunlight, oil mist, steam and vibration
environment.
Below 1000m
Altitude If the sea level is above 1000m, please derate 1% for every
additional 100m.
Vibration ≤ 5.8m/s2(0.6g)
The inverter should be installed on an upright position to ensure
Installation direction
sufficient cooling effect.
Note:
 Goodrive200A series inverters should be installed in a clean and ventilated
environment according to enclosure classification.
 Cooling air must be clean, free from corrosive materials and electrically conductive
dust.

4.2.2 Installation direction

The inverter may be installed on the wall or in a cabinet.
The inverter must be installed in an upright position. Check the installation site according to
the requirements below. Refer to chapter Dimension Drawings in the appendix for frame
details.

Fig 4-1 Installation direction of the inverter

13
Goodrive200A inverters Installation guidelines

4.2.3 Installation manner

The inverter can be installed in two different ways, depending on the frame size:
a) Wall mounting (for the inverter≤315kW)
b) Flange mounting (for the inverter≤200kW). Some need optional flange installation board.
c) Floor mounting (220kW≤the inverter≤500kW). Some need optional base.

Fig 4-2 Installation manner

(1) Mark the hole location. The location of the holes is shown in the dimension drawings in
the appendix.
(2) Fix the screws or bolts to the marked locations.
(3) Position the drive onto the wall.
(4) Tighten the screws in the wall securely.
Note:
1. The flange installation bracket is needed in the flange installation of 1.5~30kW inverters,
which the flange installation of 37~200kW inverters does not need the installation bracket.
2. 220~315kW inverters need optional base in the floor installation.

4.2.4 Multiple installations

Parallel installation

Fig 4-3 Parallel installation

Note:
 Before installing the different sizes inverters, please align their top position for the
convenience of later maintenance.
 The minimum space of B, D and C is 100mm.
14
Goodrive200A inverters Installation guidelines

4.2.5 Vertical installation

Fig 4-4 Vertical installation

Note: Windscreen should be added in vertical installation for avoiding mutual impact and
insufficient cooling.

4.2.6 Tilt installation

Fig 4-5 Tilt installation

Note: Ensure the separation of the wind input and output channels in tilt installation for
avoiding mutual impact.

15
Goodrive200A inverters Installation guidelines

4.3 Standard wiring

4.3.1 Wiring diagram of main circuit

Fig 4-6 Wring diagram of main circuit

Note:
 The fuse, DC reactor, braking unit, braking resistor, input reactor, input filter, output
reactor, output filter are optional parts. Please refer to Peripheral Optional Parts for
detailed information.
 A1 and A2 are optional parts.
 P1 and (+) are short circuited in factory, if need to connect with the DC rector, please
remove the contact tag between P1 and (+).
 Before connecting the braking resistor cable, remove the yellow labels of PB, (+),
and (-) from the terminal blocks. Otherwise, poor connection may occur.

4.3.2 Terminals figure of main circuit

Fig 4-7 0.75~5.5 kW terminals of main circuit

16
Goodrive200A inverters Installation guidelines

Fig 4-8 7.5~15kW terminals of main circuit

Fig 4-9 18.5kW terminals of main circuit

Fig 4-10 22~30kW terminals of main circuit

Fig 4-11 37~55 kW terminals of main circuit

Fig 4-12 75~110kW terminals of main circuit

17
Goodrive200A inverters Installation guidelines

Fig 4-13 132~200kW terminals of main circuit

Fig 4-14 220~315kW terminals of main circuit

Fig 4-15 350~500kW terminals of main circuit

Terminal name
Terminal Function
≤30kW ≥37kW
3-phase AC input terminals which are
R, S, T Power input of the main circuit generally connected with the power
supply.
3-phase AC output terminals which are
U, V, W The inverter output
generally connected with the motor.
This terminal is P1 and (+) are connected with the
P1 DC reactor terminal 1
inexistent terminals of DC reactor.
(+) Braking resistor DC reactor terminal 2, (+) and (-) are connected with the
18
Goodrive200A inverters Installation guidelines

Terminal name
Terminal Function
≤30kW ≥37kW
1 braking unit terminal 1 terminals of braking unit.
(-) / Braking unit terminal 2 PB and (+) are connected with the
Braking resistor This terminal is terminals of braking resistor.
PB
terminal 2 inexistent.
Protective grounding terminals, every
machine is provided 2 PE terminals as
380V:the grounding resistor is less
PE the standard configuration. These
than 10Ohm
terminals should be grounded with
proper techniques.
Optional parts (external 220V control
A1 and A2 Control power supply terminal
power supply)
Note:
 Do not use an asymmetrically constructed motor cable. If there is a symmetrically
constructed grounding conductor in the motor cable in addition to the conductive
shield, connect the grounding conductor to the grounding terminal at the inverter
and motor ends.
 Braking resistor, braking unit and DC reactor are optional parts.
 Route the motor cable, input power cable and control cables separately.
 If the terminal is not appeared, the machine does not provide the terminal as the
external terminal.

4.3.3 Wiring of terminals in main circuit

1. Fasten the grounding conductor of the input power cable with the grounding terminal of
the inverter (PE) by 360 degree grounding technique. Connect the phase conductors to R, S
and T terminals and fasten.
2. Strip the motor cable and connect the shield to the grounding terminal of the inverter by
360 degree grounding technique. Connect the phase conductors to U, V and W terminals
and fasten.
3. Connect the optional brake resistor with a shielded cable to the designated position by the
same procedures in the previous step.
4. Secure the cables outside the inverter mechanically.

Fig 4-16 Correct installation of the screw

19
Goodrive200A inverters Installation guidelines

Fig 4-17 360 degree grounding technique

4.3.4 Wiring diagram of control circuit

Fig 4-18 Wiring diagram of the control circuit

20
Goodrive200A inverters Installation guidelines

4.3.5 Terminals of control circuit

Fig 4-19 0.75~15kW Terminals of control circuit

Fig 4-20 18.5~500kW Terminals of control circuit

Note: the spare terminal is reserved and not be used.
Terminal
Description
name
+10V Local power supply +10V
AI2 1. Input range: AI2 voltage and current can be chose: 0~10V/0~20mA;
AI2 can be shifted by J4; AI3:-10V~+10V
2. Input impedance: voltage input: 20kΩ; current input: 500Ω
AI3
3. Resolution: the minimum one is 5mV when 10V corresponds to 50Hz
4. Deviation ±1%, 25℃
GND +10V reference null potential
AO1 1. Output range:0~10V or 0~20mA; AO1 can be shifted by J1; AO2 can be
shifted by J2
AO2
2. Deviation±1%,25℃
RO1A
RO1 relay output, RO1A NO, RO1B NC, RO1C common terminal
RO1B
Contactor capability: 3A/AC250V,1A/DC30V
RO1C
RO2A
RO2 relay output, RO2A NO, RO2B NC, RO2C common terminal
RO2B
Contactor capability: 3A/AC250V,1A/DC30V
RO2C

21
Goodrive200A inverters Installation guidelines

PE Grounding terminal
Provide the input switch working power supply from external to internal.
PW
Voltage range: 12~24V
The inverter provides the power supply for users with a maximum output
24V
current of 200mA
COM +24V common terminal
S1 Switch input 1
1. Internal impedance:3.3kΩ
S2 Switch input 2
2. 12~30V voltage input is available
S3 Switch input 3
3. The terminal is the dual-direction input terminal
S4 Switch input 4
supporting both NPN and PNP
S5 Switch input 5
4. Max input frequency:1kHz
S6 Switch input 6
5. All are programmable digital input terminal. User
S7 Switch input 7
can set the terminal function through function codes.
S8 Switch input 8
Except for S1~S8, this terminal can be used as high frequency input channel.
HDI
Max. input frequency:50kHz
1. Switch input:200mA/30V
HDO
2. Output frequency range:0~50kHz
COM +24V common terminal
CME Common terminal of HDO and Y1, short-connected with COM in factory
1.Swtich capability:200mA/30V
Y1
2.Output frequency range:0~1kHz
485+ 485 communication interface and 485 differential signal interface
If it is the standard 485 communication interface, please use twisted pairs or
485-
shield cable.

4.3.6 Input /Output signal connection figure

Please use U-shaped contact tag to set NPN mode or PNP mode and the internal or external
power supply. The default setting is NPN internal mode.

Fig 4-21 U-shaped contact tag

If the signal is from NPN transistor, please set the U-shaped contact tag between +24V and
PW as below according to the used power supply.
22
Goodrive200A inverters Installation guidelines

Fig 4-22 NPN modes

If the signal is from PNP transistor, please set the U-shaped contact tag as below according
to the used power supply.

Fig 4-23 PNP modes

4.4 Layout protection

4.4.1 Protecting the inverter and input power cable in short-circuit situations
Protect the inverter and input power cable in short circuit situations and against thermal
overload.
Arrange the protection according to the following guidelines.

Fig 4-24 Fuse configuration

Note: Select the fuse as the manual indicated. The fuse will protect the input power cable
from damage in short-circuit situations. It will protect the surrounding devices when the
internal of the inverter is short circuited.

23
Goodrive200A inverters Installation guidelines

4.4.2 Protecting the motor and motor cable in short-circuit situations

The inverter protects the motor and motor cable in a short-circuit situation when the motor
cable is dimensioned according to the rated current of the inverter. No additional protection
devices are needed.
 If the inverter is connected to multiple motors, a separate thermal
overload switch or a circuit breaker must be used for protecting each
cable and motor. These devices may require a separate fuse to cut off
the short-circuit current.

4.4.3 Protecting the motor against thermal overload

According to regulations, the motor must be protected against thermal overload and the
current must be switched off when overload is detected. The inverter includes a motor
thermal protection function that protects the motor and closes the output to switch off the
current when necessary.

4.4.4 Implementing a bypass connection

It is necessary to set power frequency and variable frequency conversion circuits for the
assurance of continuous normal work of the inverter if faults occur in some significant
situations.
In some special situations, for example, if it is only used in soft start, the inverter can be
conversed into power frequency running after starting and some corresponding bypass
should be added.
 Never connect the supply power to the inverter output terminals U, V
and W. Power line voltage applied to the output can result in permanent
damage to the inverter.
If frequent shifting is required, employ mechanically connected switches or contactors to
ensure that the motor terminals are not connected to the AC power line and inverter output
terminals simultaneously.

24
Goodrive200A inverters Keypad operation procedure

Keypad Operation Procedure 5

5.1 What this chapter contains

This chapter contains following operation:
• Buttons, indicating lights and the screen as well as the methods to inspect, modify and
set function codes by keypad
• Start-up

5.2 Keypad
The keypad is used to control Goodrive200A series inverters, read the state data and adjust
parameters.

A B
Fig 5-1 Keypad
Note: The keypad of 0.75~15kW as show in Fig 5-1 A, and 18.5~500kW as show in Fig 5-1
B; The inverters of 0.75~30kW can choose optional LED keypad and 0.75~500kW can
choose optional LCD keypad . The LCD keypad supports several languages, parameters
copy, high-definition display and its installation dimension is compatible with the LED.
Use strew or installation bracket to fix the external keypad. The inverters of 0.75~30kW have
standard bracket, while the inverters of 37~500kW have optimal bracket.
No. Name Description
LED off means that the inverter is in the
stopping state; LED blinking means the
RUN/TUNE inverter is in the parameter autotune
state; LED on means the inverter is in
State
1 the running state.
LED FED/REV LED
LED off means the inverter is in the
FWD/REV
forward rotation state; LED on means
the inverter is in the reverse rotation

25
Goodrive200A inverters Keypad operation procedure

No. Name Description

state
LED for keypad operation, terminals
operation and remote communication
control
LED off means that the inverter is in the
LOCAL/REMOT keypad operation state; LED blinking
means the inverter is in the terminals
operation state; LED on means the
inverter is in the remote communication
control state.
LED for faults
LED on when the inverter is in the fault
TRIP state; LED off in normal state; LED
blinking means the inverter is in the
pre-alarm state.
Mean the unit displayed currently
Hz Frequency unit
Unit RPM Rotating speed unit
2
LED A Current unit
% Percentage
V Voltage unit
Code
5-figure LED display displays various monitoring data and alarm code such
3 displayi
as set frequency and output frequency.
ng zone
Digital
4 potentio Tuning frequency. Please refer to P08.42.
meter
Enter or escape from the first level
Programming key menu and remove the parameter
quickly
Enter the menu step-by-step
Entry key
Confirm parameters
Increase data or function code
UP key
5 Buttons progressively
Decrease data or function code
DOWN key
progressively
Move right to select the displaying
parameter circularly in stopping and
Right-shift key
running mode.
Select the parameter modifying digit
26
Goodrive200A inverters Keypad operation procedure

No. Name Description

during the parameter modification
This key is used to operate on the
Run key
inverter in key operation mode
This key is used to stop in running state
Stop/ and it is limited by function code P07.04
Reset key This key is used to reset all control
modes in the fault alarm state
The function of this key is confirmed by
Quick key
function code P07.02.

5.3 Keypad displaying

The keypad displaying state of Goodrive200A series inverters is divided into stopping state
parameter, running state parameter, function code parameter editing state and fault alarm
state and so on.

Fig 5-2 Displayed state

5.4 Keypad operation

Operate the inverter via operation panel. See the detailed structure description of function
codes in the brief diagram of function codes.

5.4.1 How to modify the function codes of the inverter

The inverter has three levels menu, which are:
1. Group number of function code (first-level menu)
2. Tab of function code (second-level menu)
3. Set value of function code (third-level menu)
Remarks: Press both the PRG/ESC and the DATA/ENT can return to the second-level menu
from the third-level menu. The difference is: pressing DATA/ENT will save the set
parameters into the control panel, and then return to the second-level menu with shifting to
the next function code automatically; while pressing PRG/ESC will directly return to the
second-level menu without saving the parameters, and keep staying at the current function
code.
Under the third-level menu, if the parameter has no flickering bit, it means the function code
27
Goodrive200A inverters Keypad operation procedure
cannot be modified. The possible reasons could be:
1) This function code is not modifiable parameter, such as actual detected parameter,
operation records and so on;
2) This function code is not modifiable in running state, but modifiable in stop state.
Example: Set function code P00.01 from 0 to 1.

Fig 5-3 Sketch map of modifying parameters

5.4.2 How to set the password of the inverter

Goodrive200A series inverters provide password protection function to users. Set P7.00 to
gain the password and the password protection becomes valid instantly after quitting from
the function code editing state. Press PRG/ESC again to the function code editing state,
“0.0.0.0.0” will be displayed. Unless using the correct password, the operators cannot enter
it.
Set P7.00 to 0 to cancel password protection function.
The password protection becomes effective instantly after retreating form the function code
editing state. Press PRG/ESC again to the function code editing state, “0.0.0.0.0” will be
displayed. Unless using the correct password, the operators cannot enter it.

Fig 5-4 Sketch map of password setting

5.4.3 How to watch the inverter state through function codes
Goodrive200A series inverters provide group P17 as the state inspection group. Users can
enter into P17 directly to watch the state.

Fig 5-5 Sketch map of state watching

28
Goodrive200A inverters Function parameters

Function Parameters 6

6.1 What this chapter contains

This chapter lists and describes the function parameters.

6.2 Goodrive200A general series function parameters

The function parameters of Goodrive200A series inverters have been divided into 30 groups
(P00~P29) according to the function, of which P18~P28 are reserved. Each function group
contains certain function codes applying 3-level menus. For example, “P08.08” means the
eighth function code in the P8 group function, P29 group is factory reserved, and users are
forbidden to access these parameters.
For the convenience of function codes setting, the function group number corresponds to the
first level menu, the function code corresponds to the second level menu and the function
code corresponds to the third level menu.
1. Below is the instruction of the function lists:
The first line “Function code”: codes of function parameter group and parameters;
The second line “Name”: full name of function parameters;
The third line “Detailed illustration of parameters”: detailed illustration of the function
parameters;
The fourth line “Default value”: the original factory set value of the function parameter;
The fifth line “Modify”: the modifying character of function codes (the parameters can be
modified or not and the modifying conditions), below is the instruction:
“○”: means the set value of the parameter can be modified on stop and running state;
“◎”: means the set value of the parameter can not be modified on the running state;
“●”: means the value of the parameter is the real detection value which can not be
modified.
(The inverter has limited the automatic inspection of the modifying character of the
parameters to help users avoid mismodifying).
2. “Parameter radix” is decimal (DEC), if the parameter is expressed by hex, then the
parameter is separated from each other when editing. The setting range of certain bits are
0~F (hex).
3.”The default value” means the function parameter will restore to the default value during
default parameters restoring. But the detected parameter or recorded value won’t be
restored.
4. For a better parameter protection, the inverter provides password protection to the
parameters. After setting the password (set P07.00 to any non-zero number), the system will
come into the state of password verification firstly after the user press PRG/ESC to come
into the function code editing state. And then “0.0.0.0.0.” will be displayed. Unless the user
input right password, they cannot enter into the system. For the factory setting parameter
zone, it needs correct factory password (remind that the users can not modify the factory
parameters by themselves, otherwise, if the parameter setting is incorrect, damage to the
inverter may occur). If the password protection is unlocked, the user can modify the

29
Goodrive200A inverters Function parameters
password freely and the inverter will work as the last setting one. When P07.00 is set to 0,
the password can be canceled. If P07.00 is not 0 during powering on, then the parameter is
protected by the password. When modify the parameters by serial communication, the
function of the password follows the above rules, too.
Function Default
Name Detailed instruction of parameters Modify
code value
P00 Group Basic function group
1: Sensorless vector control mode 1 (applying to
AM)
No need to install encoders. It is suitable in cases
with high speed control accuracy for accurate
speed and torque control at all power ratings.
Speed 2:SVPWM control
P00.00 2 ◎
control mode No need to install encoders. It can improve the
control accuracy with the advantages of stable
operation, valid low-frequency torque boost and
current vibration suppression and the functions of
slip compensation and voltage adjustment.
Note: AM-Asynchronous motor
Select the run command channel of the inverter.
The control command of the inverter includes:
start-up, stop, forward, reverse, jogging and fault
reset.
0:Keypad running command
channel(“LOCAL/REMOT” light off)
Carry out the command control by RUN,
STOP/RST on the keypad.
Set the multi-function key QUICK/JOG as
FWD/REV shifting function (P07.02=3) to change
Run the running direction; press RUN and
P00.01 command STOP/RST simultaneously in running state to 0 ○
channel make the inverter coast to stop.
1:Terminal running command channel
(“LOCAL/REMOT” flickering)
Carry out the running command control by the
forward rotation, reverse rotation and forward
jogging and reverse jogging of the multi-function
terminals
2:Communication running command channel
(“LOCAL/REMOT” on);
The running command is controlled by the upper
monitor via communication.

30
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
Communicati 0: MODBUS communication
P00.02 0 ○
on selection 1~3: Reserved
This parameter is used to set the Maximum
output frequency of the inverter. Users should
Max. output pay attention to this parameter because it is the 50.00
P00.03 ◎
frequency foundation of the frequency setting and the Hz
speed of acceleration and deceleration.
Setting range: P00.04~400.00Hz
The upper limit of the running frequency is the
upper limit of the output frequency of the inverter
Upper limit of
which is lower than or equal to the maximum 50.00
P00.04 the running ◎
frequency. Hz
frequency
Setting range:P00.05~P00.03 (Max. output
frequency)
The lower limit of the running frequency is that of
the output frequency of the inverter.
The inverter runs at the lower limit frequency if
Lower limit of the set frequency is lower than the lower limit
P00.05 the running one. 0.00Hz ◎
frequency Note: Max. output frequency ≥ Upper limit
frequency ≥ Lower limit frequency
Setting range:0.00Hz~P00.04 (Upper limit of the
running frequency)
A frequency Note: Frequency A and frequency B cannot use
P00.06 0 ○
command the same frequency setting mode. The frequency
source can be set by P00.09.
0:Keypad data setting
Modify the value of P00.10 (set the frequency by
keypad) to modify the frequency by the keypad.
1:Analog AI1 setting(The inverter(≤15kW) can
be set by the analog potentiometer on the keypad
and AI1 setting is not available for the device
B frequency which is 18.5kW or higer than 18.5kW)
P00.07 2 ○
command 2:Analog AI2 setting
3:Analog AI3 setting
Set the frequency by analog input terminals.
Goodrive200A series inverters provide 3
channels analog input terminals as the standard
configuration, of which AI1/AI2 are the
voltage/current option (0~10V/0~20mA) which
can be shifted by jumpers; while AI3 is voltage
31
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
input (-10V~+10V).
Note: when analog AI1/AI2 select 0~20mA input,
the corresponding voltage of 20mA is 10V.
100.0% of the analog input setting corresponds
to the maximum frequency (function code
P00.03) in forward direction and -100.0%
corresponds to the maximum frequency in
reverse direction (function code P00.03)
4:High-speed pulse HDI setting
The frequency is set by high-speed pulse
terminals. Goodrive200A series inverters provide
1 channel high speed pulse input as the standard
configuration. The pulse frequency range is
0.00~50.00kHz.
100.0% of the high speed pulse input setting
corresponds to the maximum frequency in
forward direction (P00.03) and -100.0%
corresponds to the maximum frequency in
reverse direction (P00.03).
Note: The pulse setting can only be input by
multi-function terminals HDI. Set P05.00 (HDI
input selection) to high speed pulse input, and
set P05.49 (HDI high speed pulse input function
selection) to frequency setting input.
5:Simple PLC program setting
The inverter runs at simple PLC program mode
when P00.06=5 or P00.07=5. Set P10 (simple
PLC and multi-step speed control) to select the
running frequency, running direction, ACC/DEC
time and the keeping time of corresponding step.
See the function description of P10 for detailed
information.
6: Multi-step speed running setting
The inverter runs at multi-step speed mode when
P00.06=6 or P00.07=6. Set P05 to select the
current running step, and set P10 to select the
current running frequency.
The multi-step speed has the priority when
P00.06 or P00.07 does not equal to 6, but the
setting step can only be the 1~15 step. The
setting step is 0~15 if P00.06 or P00.07 equals to

32
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
6.
7: PID control setting
The running mode of the inverter is process PID
control when P00.06=7 or P00.07=7. It is
necessary to set P09. The running frequency of
the inverter is the value after PID effect. See P09
for the detailed information of the preset source,
preset value, and feedback source of PID.
8:MODBUS communication setting
The frequency is set by MODBUS
communication. See P14 for detailed information.
9~11: Reserved
0:Maximum output frequency, 100% of
B frequency setting corresponds to the maximum
B frequency output frequency
P00.08 command 1: A frequency command, 100% of B frequency 0 ○
reference setting corresponds to the maximum output
frequency. Select this setting if it needs to adjust
on the base of A frequency command.
0: A, the current frequency setting is A frequency
command
1: B, the current frequency setting is B frequency
command
2: A+B, the current frequency setting is A
frequency command + B frequency command
3: A-B, the current frequency setting is A
Combination
frequency command - B frequency command
P00.09 of the setting 0 ○
4: Max (A, B): the bigger one between A
source
frequency command and B frequency is the set
frequency.
5: Min (A, B): The lower one between A
frequency command and B frequency is the set
frequency.
Note:The combination manner can be shifted by
P05(terminal function)
When A and B frequency commands are selected
as “keypad setting”, this parameter will be the
Keypad set 50.00
P00.10 initial value of inverter reference frequency ○
frequency Hz
Setting range:0.00 Hz~P00.03
(the Max. frequency)

33
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
ACC time means the time needed if the inverter
speeds up from 0Hz to the Max. One (P00.03). Depend
P00.11 ACC time 1 DEC time means the time needed if the inverter on ○
speeds down from the Max. Output frequency to model
0Hz (P00.03).
Goodrive200A series inverters define four
groups of ACC/DEC time which can be selected
Depend
by P05. The factory default ACC/DEC time of the
P00.12 DEC time 1 on ○
inverter is the first group.
model
Setting range of P00.11 and P00.12:0.0~3600.0s
0: Runs at the default direction, the inverter runs
in the forward direction. FWD/REV indicator is
off.
1: Runs at the opposite direction, the inverter
runs in the reverse direction. FWD/REV indicator
is on.
Modify the function code to shift the rotation
direction of the motor. This effect equals to the
shifting the rotation direction by adjusting either
two of the motor lines (U, V and W). In keypad
Running control, the motor rotation direction can be
P00.13 0 ○
direction changed by QUICK/JOG on the keypad. Refer to
parameter P07.02.
Note: When the function parameter comes back
to the default value, the motor’s running direction
will come back to the factory default state, too. In
some cases it should be used with caution after
commissioning if the change of rotation direction
is disabled.
2: Forbid to run in reverse direction: It can be
used in some special cases if the reverse running
is disabled.

Carrier Depend
P00.14 frequency on ○
setting model

34
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
The relationship table of the motor type and
carrier frequency:
Factory setting of
Model
carrier frequency
1.5~11kW 8kHz
15~55kW 4kHz
Above 75kW 2kHz
The advantage of high carrier frequency: ideal
current waveform, little current harmonic wave
and motor noise.
The disadvantage of high carrier frequency:
increasing the switch loss, increasing inverter
temperature and the impact to the output
capacity. The inverter needs to derate on high
carrier frequency. At the same time, the leakage
and electrical magnetic interference will increase.
Applying low carrier frequency is contrary to the
above, too low carrier frequency will cause
unstable running, torque decreasing and surge.
The manufacturer has set a reasonable carrier
frequency when the inverter is in factory. In
general, users do not need to change the
parameter.
When the frequency used exceeds the default
carrier frequency, the inverter needs to derate
10% for each additional 1k carrier frequency.
Setting range:1.0~15.0kHz
0:No operation
1:Rotation autotuning
Comprehensive motor parameter autotune
It is recommended to use rotation autotuning
when high control accuracy is needed.
Motor
2:Static autotuning 1
P00.15 parameter 0 ◎
It is suitable in the cases when the motor can not
autotuning
de-couple from the load.
3:Static autotuning 2
It is suitable in the cases when the motor can not
de-couple form the load. But only for parts of
parameters.
P00.16 AVR function 0:Invalid 1 ○
35
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
selection 1:Valid during the whole procedure
The auto-adjusting function of the inverter can
cancel the impact on the output voltage of the
inverter because of the bus voltage fluctuation.
0:G type, for the constant torque load of rated
parameters
1:P type; for the variable torque load of rated
P00.17 Inverter type parameters (fans and water pumps) 0 ◎
GD200A series inverters can use G/P type, the
available motor power of G type is small one
power file than that of P type.
0:No operation
1:Restore the default value
2:Clear fault records
Function
Note: The function code will restore to 0 after
P00.18 restore 0 ◎
finishing the operation of the selected function
parameter
code.
Restoring to the default value will cancel the user
password, please use this function with caution.
P01 Group Start-up and stop control
0:Start-up directly:start from the starting
frequency P01.01
1:Start-up after DC braking: start the motor from
the starting frequency after DC braking (set the
parameter P01.03 and P01.04). It is suitable in
the cases where reverse rotation may occur to
the low inertia load during starting.
P01.00 Start mode 0 ◎
2: Start-up after speed tracking: start the rotating
motor smoothly after tracking the rotation speed
and direction automatically. It is suitable in the
cases where reverse rotation may occur to the
big inertia load during starting.
Note: This function is available for the inverters of
4kW and above.
Starting frequency of direct start-up means the
Starting
original frequency during the inverter starting.
P01.01 frequency of 0.50Hz ◎
See P01.02 for detailed information.
direct start
Setting range: 0.00~50.00Hz
Retention Set a proper starting frequency to increase the
P01.02 0.0s ◎
time of the torque of the inverter during starting. During the

36
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
starting retention time of the starting frequency, the
frequency output frequency of the inverter is the starting
frequency. And then, the inverter will run from the
starting frequency to the set frequency. If the set
frequency is lower than the starting frequency,
the inverter will stop running and keep in the
stand-by state. The starting frequency is not
limited in the lower limit frequency.

Setting range: 0.0~50.0s

The braking The inverter will carry out DC braking at the
current braking current set before starting and it will
P01.03 0.0% ◎
before speed up after the DC braking time. If the DC
starting braking time is set to 0, the DC braking is invalid.
The stronger the braking current, the bigger the
braking power. The DC braking current before
The braking
starting means the percentage of the rated
P01.04 time before 0.00s ◎
current of the inverter.
starting
The setting range of P01.03: 0.0~100.0%
The setting range of P01.04: 0.00~50.00s
The changing mode of the frequency during
start-up and running.
0:Linear type
The output frequency increases or decreases
linearly.
ACC/DEC
P01.05 0 ◎
selection

37
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value

1: S curve
ACC time of
the starting
P01.06 0.1s ○
step of S
curve
0.0~50.0s
DEC time of
the ending
P01.07 0.1s ○
step of S
curve
0: Decelerate to stop: after the stop command
becomes valid, the inverter decelerates to reduce
the output frequency during the set time. When
the frequency decreases to 0Hz, the inverter
P01.08 Stop mode stops. 0 ○
1: Coast to stop: after the stop command
becomes valid, the inverter ceases the output
immediately. And the load coasts to stop at the
mechanical inertia.
Starting Starting frequency of DC braking: start the DC
P01.09 frequency of braking when running frequency reaches starting 0.00Hz ○
DC braking frequency determined by P1.09.
Waiting time Waiting time before DC braking: Inverters block
P01.10 before DC the output before starting the DC braking. After 0.00s ○
braking this waiting time, the DC braking will be started
DC braking so as to prevent over-current fault caused by DC
P01.11 braking at high speed. 0.0% ○
current
DC braking current：The value of P01.11 is the
percentage of rated current of inverter. The
bigger the DC braking current is, the greater the
DC braking braking torque is.
P01.12 0.00s ○
time DC braking time: The retention time of DC brake.
If the time is 0, the DC brake is invalid. The
inverter will stop at the set deceleration time.

38
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value

Setting range of P01.09: 0.00Hz~P00.03

(the Max. frequency)
Setting range of P01.10: 0.00~50.00s
Setting range of P01.11: 0.0~100.0%
Setting range of P01.12: 0.00~50.00s
During the procedure of switching FWD/REV
rotation, set the threshold by P01.14, which is as
the table below:

Dead time of
P01.13 FWD/REV 0.0s ○
rotation

Setting range: 0.0~3600.0s

Shifting Set the threshold point of the inverter:
between 0:Switch after 0 frequency
P01.14 0 ◎
FWD/REV 1:Switch after the starting frequency
rotation 2:Switch after the stopping speed
Stopping
P01.15 0.00~100.00Hz 0.50 Hz ◎
speed
0: Detect according to speed setting (no stopping
Detection of
delay)
P01.16 stopping 1 ◎
1: Detect according to speed feedback (only valid
speed
for vector control)
Detection If set P01.16 to 1, the feedback frequency is less
time of the than or equal to P01.15 and detect in the set time
P01.17 0.50s ◎
feedback of P01.17, the inverter will stop; otherwise the
speed inverter will stop after the set time of P01.17

39
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value

Setting range: 0.00~100.00s (only valid when

P01.16=1)
When the running command channel is the
terminal control, the system will detect the state
of the running terminal during powering on.
0: The terminal running command is invalid when
powering on. Even the running command is
detected to be valid during powering on, the
Operation inverter won’t run and the system keeps in the
protection protection state until the running command is
P01.18 0 ○
during canceled and enabled again.
powering on 1: The terminal running command is valid when
powering on. If the running command is detected
to be valid during powering on, the system will
start the inverter automatically after the
initialization.
Note: this function should be selected with
cautions, or serious result may follow.
This function code determines the running state
Action
of the inverter when the set frequency is lower
selection
than the lower-limit one.
(operation
0: Run at the lower limit frequency
frequency<lo
1: Stop
wer
P01.19 2: Hibernation 0 ◎
frequency
The inverter will coast to stop when the set
limit and valid
frequency is lower than the lower-limit one. If the
when the
set frequency is above the lower limit one again
lower
and it lasts for the time set by P01.20, the inverter
limit >0)
will come back to the running state automatically.
This function code determines the hibernation
delay time. When the running frequency of the
Hibernation inverter is lower than the lower limit one, the
P01.20 restore delay inverter will pause to stand by. 0.0s ○
time When the set frequency is above the lower limit
one again and it lasts for the time set by P01.20,
the inverter will run automatically.

40
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
Note: The time is the total value when the set
frequency is above the lower limit one.

Setting range: 0.0~3600.0s

(valid when P01.19=2)
This function can enable the inverter start or not
after the power off and then power on.
Restart after 0: Disable
P01.21 0 ○
power off 1: Enable, if the starting need is met, the inverter
will run automatically after waiting for the time
defined by P01.22.
The function determines the waiting time before
the automatic running of the inverter when
powering off and then powering on.
The waiting
time of
P01.22 1.0s ○
restart after
power off

Setting range: 0.0~3600.0s

(valid when P01.21=1)
The function determines the brake release after
the running command is reference, and the
Start delay
P01.23 inverter is in a stand-by state and wait for the 0.0s ○
time
delay time set by P01.23
Setting range: 0.0~60.0s

Delay time of
P01.24 the stop 0.0s ●
speed

Setting range: 0.0~100.0 s

41
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
0: Output without voltage
0Hz output
P01.25 1: Output with voltage 0 ●
selection
2: Output at the DC braking current
P02 Group Motor 1
Depend
Rated power
P02.01 0.1~3000.0kW on ◎
of AM 1
model
Rated
50.00
P02.02 frequency of 0.01Hz~P00.03(the Max. frequency) ◎
Hz
AM 1
Depend
Rated speed
P02.03 1~36000rpm on ◎
of AM 1
model
Rated Depend
P02.04 voltage of 0~1200V on ◎
AM 1 model
Depend
Rated current
P02.05 0.8~6000.0A on ◎
of AM 1
model
Stator Depend
P02.06 resistor of 0.001~65.535Ω on ○
AM 1 model
Rotor Depend
P02.07 resistor of 0.001~65.535Ω on ○
AM 1 model
Leakage Depend
P02.08 inductance of 0.1~6553.5mH on ○
AM 1 model
Mutual Depend
P02.09 inductance of 0.1~6553.5mH on ○
AM 1 model
Non-load Depend
P02.10 current of AM 0.1~6553.5A on ○
1 model
0: No protection
1: Common motor (with low speed
compensation). Because the heat-releasing
Motor 1
effect of the common motors will be weakened,
P02.26 overload 2 ◎
the corresponding electric heat protection will be
protection
adjusted properly. The low speed compensation
characteristic mentioned here means reducing
the threshold of the overload protection of the
42
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
motor whose running frequency is below 30Hz.
2: Variable frequency motor (without low speed
compensation) Because the heat-releasing effect
of the specific motors won’t be impacted by the
rotation speed, it is not necessary to adjust the
protection value during low-speed running.
Times of motor overload M = Iout/(In*K)
In is the rated current of the motor, Iout is the
output current of the inverter and K is the motor
protection coefficient.
So, the bigger the value of K is, the smaller the
value of M is. When M =116%, the fault will be
reported after 1 hour, when M =200%, the fault
Motor 1 over
will be reported after 1 minute, when M>=400%,
load
P02.27 the fault will be reported instantly. 100.0% ○
protection
coefficient

Setting range: 20.0%~120.0%

Correction Correct the power displaying of motor 1.
coefficient of Only impact the displaying value other than the
P02.28 control performance of the inverter. 1.00 ●
motor 1
power Setting range: 0.00~3.00
P03 Group Vector control
Speed loop
P03.00 proportional The parameters P03.00~P03.05 only apply to 20.0 ○
gain1 vector control mode. Below the switching
Speed loop frequency 1(P03.02), the speed loop PI
P03.01 0.200s ○
integral time1 parameters are: P03.00 and P03.01. Above the
Low switching frequency 2(P03.05), the speed loop PI
P03.02 switching parameters are: P03.03 and P03.04. PI 5.00Hz ○
frequency parameters are gained according to the linear
Speed loop change of two groups of parameters. It is shown
P03.03 proportional as below: 20.0 ○
gain 2

43
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
Speed loop PI parameters
P03.04 integral time (P03.00,P03.01) 0.200s ○
2

(P03.03,P03.04)

P03.02 P03.05 Output frequency

Setting the proportional coefficient and integral

time of the adjustor can change the dynamic
response performance of vector control speed
loop. Increasing the proportional gain and
decreasing the integral time can speed up the
dynamic response of the speed loop. But too high
proportional gain and too low integral time may
High
cause system vibration and overshoot. Too low
P03.05 switching 10.00Hz ○
proportional gain may cause system vibration
frequency
and speed static deviation.
PI has a close relationship with the inertia of the
system. Adjust on the base of PI according to
different loads to meet various demands.
The setting range of P03.00:0~200.0
The setting range of P03.01: 0.000~10.000s
The setting range of P03.02:0.00Hz~P03.05
The setting range of P03.03:0~200.0
The setting range of P03.04: 0.000~10.000s
The setting range of P03.05:P03.02~P00.03(the
Max. output frequency)
Speed loop
P03.06 0~8 (corresponds to 0~28/10ms) 0 ○
output filter
Compensatio
n coefficient Slip compensation coefficient is used to adjust
P03.07 100% ○
of electro the slip frequency of the vector control and
motion slip improve the speed control accuracy of the
Compensatio system. Adjusting the parameter properly can
n coefficient control the speed steady-state error.
P03.08 100% ○
of braking Setting range:50~200%
slip
Current loop Note:
P03.09 percentage 1 These two parameters adjust the PI adjustment 1000 ○
coefficient P parameter of the current loop which affects the

44
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
dynamic response speed and control accuracy
Current loop directly. Generally, users do not need to change
P03.10 integral the default value. 1000 ○
coefficient 1 2 Only apply to SVC control mode 0(P00.00=0).
Setting range:0~65535
This parameter is used to enable the torque
control mode, and set the torque.
0:Torque control is invalid
1:Keypad setting torque(P03.12)
2:Analog AI1 setting torque(The inverter( ≤
15kW) can be set by the analog potentiometer on
the keypad and AI1 setting is not available for the
Torque
device which is 18.5kW or higer than 18.5kW)
P03.11 setting 0 ○
3:Analog AI2 setting torque
method
4:Analog AI3 setting torque
5:Pulse frequency HDI setting torque
6:Multi-step torque setting
7:MODBUS communication setting torque
8~10:Reserved
Note: Setting modes 2~10, 100% corresponds to
three times of the rated current of the motor.
Keypad Setting range: -300.0%~300.0%(rated current of
P03.12 50.0% ○
setting torque the motor)
Torque
P03.13 reference 0.000~10.000s 0.010s ○
filter time
Upper 0:Keypad
frequency of (P03.16 sets P03.14,P03.17 sets P03.15)
P03.14 forward 1: AI1 (The inverter(≤15kW) can be set by the 0 ○
rotation in analog potentiometer on the keypad and AI1
vector control setting is not available for the device which is
18.5kW or higer than 18.5kW)
2: AI2
3: AI3
Upper
4:Pulse frequency HDI setting upper-limit
frequency of
frequency
P03.15 reverse 0 ○
5:Multi-step setting upper-limit frequency
rotation in
6:MODBUS communication setting upper-limit
vector control
frequency
7~ 9: Reserved
Note: Setting method 1~9, 100% corresponds to
45
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
the maximum frequency

Keypad
setting for
upper
P03.16 50.00 Hz ○
frequency of
This function is used to set the upper limit of the
forward
frequency. P03.16 sets the value of P03.14;
rotation
P03.17 sets the value of P03.15.
Keypad
Setting range:0.00 Hz~P00.03 (the Max. output
setting for
frequency)
P03. upper
50.00Hz ○
17 frequency of
reverse
rotation
Upper electro This function code is used to select the electro
motion motion and braking torque upper-limit setting
P03.18 0 ○
torque source selection.
source 0:Keypad setting upper-limit frequency
(P03.20 sets P03.18, P03.21 sets P03.19)
1: AI1 (The inverter(≤15kW) can be set by the
analog potentiometer on the keypad and AI1
setting is not available for the device which is
Upper
18.5kW or higer than 18.5kW)
braking
P03.19 2: AI2 0 ○
torque
3: AI3
source
4: HDI
5:MODBUS communication
Note: setting mode 1~9,100% corresponds to
three times of the motor current.
Keypad
setting of
P03.20 180.0% ○
electromotion
The function code is used to set the limit of the
torque
torque.
Keypad
Setting range:0.0~300.0%(motor rated current)
setting of
P03.21 180.0% ○
braking
torque
Weakening
coefficient in
P03.22 The usage of motor in weakening control. 0.3 ○
constant
power zone

46
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value

Lowest
weakening
P03.23 point in Function code P03.22 and P03.23 are effective 20% ○
constant at constant power. The motor will enter into the
power zone weakening state when the motor runs at rated
speed. Change the weakening curve by
modifying the weakening control coefficient. The
bigger the weakening control coefficient is, the
steeper the weak curve is.
The setting range of P03.22:0.1~2.0
The setting range of P03.23:10%~100%
P03.24 set the Max. Voltage of the inverter, which
Max. voltage
P03.24 is dependent on the site situation. 100.0% ◎
limit
The setting range:0.0~120.0%
Reactivate the motor when the inverter starts up.
Build up a magnetic field inside the inverter to
Pre-exciting
P03.25 improve the torque performance during the 0.300s ○
time
starting process.
The setting time:0.000~10.000s
Weak
0~8000
magnetic
P03.26 Note: P03.24~P03.26 are invalid for vector 1000 ○
proportional
mode.
gain
Vector 0: Display the actual value
P03.27 0 ○
control speed 1: Display the setting value
Compensatio
0.0~100.0%
n coefficient
P03.28 Adjust P03.28 to compensate the coefficient of 0.0% ○
of static
static friction. Only valid when setting in 1Hz.
friction
Compensatio
0.0~100.0%
n coefficient
P03.29 Adjust P03.29 to compensate the coefficient of 0.0% ○
of dynamic
static friction. Only valid when setting in 1Hz.
friction
P04 Group SVPWM control
Motor 1 V/F These function codes define the V/F curve of
P04.00 0 ◎
curve setting Goodrive200A motor 1, and meet the need of

47
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
different loads.
0:Straight line V/F curve；applying to the constant
torque load
1:Multi-dots V/F curve
2:1.3th power low torque V/F curve
3:1.7th power low torque V/F curve
4:2.0th power low torque V/F curve
Curves 2~4 apply to the torque loads such as
fans and water pumps. Users can adjust
according to the features of the loads to achieve
a best energy-saving effect.
5:Customized V/F(V/F separation); in this mode,
V can be separated from f and f can be adjusted
through the frequency reference channel set by
P00.06 or the voltage reference channel set by
P04.27 to change the feature of the curve.
Note: Vb in the below picture is the motor rated
voltage and fb is the motor rated frequency.

Torque boost is used for the compensation of low

frequency torque. P04.01 is relative to the Max.
output voltage Vb.
P04.02 defines the percentage of closing
frequency of manual torque to fb.
Torque boost should be selected according to the
Motor 1
P04.01 load. The bigger the load is, the bigger the torque 0.0% ○
torque boost
is. Too big torque boost is inappropriate because
the motor will run with over magnetic, and the
current of the inverter will increase to add the
temperature of the inverter and decrease the
efficiency.
When the torque boost is set to 0.0%, the inverter
is automatic torque boost.
Motor 1 Torque boost threshold: below this frequency
P04.02 torque boost point, the torque boost is effective, but over this 20.0% ○
frequency point, the torque boost is invalid.
close

48
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value

The setting range of P04.01:0.0%:(automatic)

0.1%~10.0%
The setting range of P04.02:0.0%~50.0%
V/F
P04.03 frequency 1 0.00Hz ○
of motor 1
V/F voltage 1
P04.04 00.0% ○
of motor 1
V/F
P04.05 frequency 2 00.00Hz ○
of motor 1
V/F voltage 2
P04.06 When P04.00 =1, the user can set V/F curve 00.0% ○
of motor 1
through P04.03~P04.08.
V/F V/F is generally set according to the load of the
P04.07 frequency 3 motor. 00.00Hz ○
of motor 1 Note:V1＜V2＜V3, f1＜f2＜f3. Too high low
frequency voltage will heat the motor excessively
or damage. The inverter may occur the
overcurrent speed or overcurrent protection.
The setting range of P04.03: 0.00Hz~P04.05
The setting range of P04.04:0.0%~110.0%
V/F voltage 3 The setting range of P04.05:P04.03~ P04.07
P04.08 00.0% ○
of motor 1 The setting range of P04.06:0.0%~110.0%
(the rated voltage of motor 1)
The setting range of P04.07:P04.05~ P02.02
(the rated frequency of motor 1)
The setting range of P04.08:0.0%~110.0%
(the rated voltage of motor 1)
This function code is used to compensate the
V/F slip
change of the rotation speed caused by load
compensatio
P04.09 during compensation SVPWM control to improve 100.0% ○
n gain of
the rigidity of the motor. It can be set to the rated
motor 1
slip frequency of the motor which is counted as

49
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
below:
△f=fb-n*p/60
Of which, fb is the rated frequency of the motor, its
function code is P02.02; n is the rated rotating
speed of the motor and its function code is
P02.03; p is the pole pair of the motor. 100.0%
corresponds to the rated slip frequency△f.
Setting range:0.0~200.0%
Motor 1 low
frequency In the SVPWM control mode, current fluctuation
P04.10 10 ○
vibration may occur to the motor on some frequency,
control factor especially the motor with big power. The motor
Motor 1 high can not run stably or overcurrent may occur.
frequency These phenomena can be canceled by adjusting
P04.11 10 ○
vibration this parameter.
control factor The setting range of P04.10:0~100
Motor 1 The setting range of P04.11:0~100
vibration The setting range of P04.12:0.00Hz~P00.03
P04.12 30.00 Hz ○
control (the Max. frequency)
threshold
0:No action
Energy-savin
1:Automatic energy-saving operation
P04.26 g operation 0 ◎
Motor on the light load conditions, automatically
selection
adjusts the output voltage to save energy
Select the output setting channel at V/F curve
separation.
0: Keypad setting voltage: the output voltage is
determined by P04.28.
1:AI1 setting voltage(The inverter(≤15kW) can
be set by the analog potentiometer on the keypad
and AI1 setting is not available for the device
Voltage
which is 18.5kW or higer than 18.5kW)
P04.27 setting 0 ○
2:AI2 setting voltage;
channel
3:AI3 setting voltage;
4:HDI setting voltage;
5:Multi-step speed setting voltage;
6:PID setting voltage;
7:MODBUS communication setting voltage;
Note: 100% corresponds to the rated voltage of
the motor.
P04.28 Keypad The function code is the voltage digital set value 100.0% ○
50
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
setting when the voltage setting channel is selected as
voltage “keypad selection”
The setting range:0.0%~100.0%
Voltage Voltage increasing time is the time when the
P04.29 increasing inverter accelerates from the output minimum 5.0s ○
time voltage to the output maximum voltage.
Voltage decreasing time is the time when the
Voltage
inverter decelerates from the output maximum
P04.30 decreasing 5.0s ○
voltage to the output minimum voltage.
time
The setting range:0.0~3600.0s
Maximum Set the upper and low limit of the output voltage.
P04.31 output The setting range of P04.31:P04.32~100.0% 100.0% ◎
voltage (the rated voltage of the motor)
The setting range of P04.32:0.0%~ P04.31
(the rated voltage of the motor)

Minimum
P04.32 output 0.0% ◎
voltage

Used to adjust the output voltage of inverter in

SVPWM mode when weaking magnetic.
Note: Invalid in constant-torque mode.

Weaking
coefficient at
P04.33 1.00 ●
constant
power

The setting range of P04.33: 1.00~1.30

P05 Group Input terminals
0: HDI is high pulse input. See P05.49~P05.54
P05.00 HDI input 0 ◎
1: HDI is switch input
S1 terminal 0: No function
P05.01 function 1: Forward rotation 1 ◎
selection 2: Reverse rotation

51
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
S2 terminal 3: 3-wire control
P05.02 function 4: Forward jogging 4 ◎
selection 5: Reverse jogging
S3 terminal 6: Coast to stop
P05.03 function 7: Fault reset 7 ◎
selection 8: Operation pause
S4 terminal 9: External fault input
P05.04 function 10:Increasing frequency setting(UP) 0 ◎
selection 11:Decreasing frequency setting(DOWN)
S5 terminal 12:Cancel the frequency change setting
P05.05 function 13:Shift between A setting and B setting 0 ◎
selection 14:Shift between combination setting and A
S6 terminal setting
P05.06 function 15:Shift between combination setting and B 0 ◎
selection setting
S7 terminal 16:Multi-step speed terminal 1
P05.07 function 17:Multi-step speed terminal 2 0 ◎
selection 18:Multi-step speed terminal 3
S8 terminal 19:Multi- step speed terminal 4
P05.08 function 20:Multi- step speed pause 0 ◎
selection 21:ACC/DEC time option 1
22:ACC/DEC time option 2
23:Simple PLC stop reset
24:Simple PLC pause
25:PID control pause
26:Traverse Pause(stop at the current frequency)
27:Traverse reset(return to the center frequency)
28:Counter reset
29:Torque control prohibition
30:ACC/DEC prohibition
HDI terminal
31:Counter trigger
P05.09 function 0 ◎
32:Length reset
selection
33:Cancel the frequency change setting
temporarily
34:DC brake
36:Shift the command to the keypad
37:Shift the command to the terminals
38:Shift the command to the communication
39: Pre-exciting command
40:Clear the power
41:Keep the power

52
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
61: PID pole switching

The function code is used to set the polarity of

the input terminals.
Set the bit to 0, the input terminal is anode.
Polarity
Set the bit to 1, the input terminal is cathode.
selection of
P05.10 BIT0 BIT1 BIT2 BIT3 BIT4 0x000 ○
the input
S1 S2 S3 S4 S5
terminals
BIT5 BIT6 BIT7 BIT8
S6 S7 S8 HDI
The setting range:0x000~0x1FF
Set the sample filter time of S1~S8 and HDI
ON-OFF filter terminals. If the interference is strong, increase
P05.11 0.010s ○
time the parameter to avoid the disoperation.
0.000~1.000s
0x000~0x1FF(0: Disabled, 1:Enabled )
BIT0:S1 virtual terminal
BIT1:S2 virtual terminal
BIT2:S3 virtual terminal
Virtual
BIT3:S4 virtual terminal
P05.12 terminals 0x000 ◎
BIT4:S5 virtual terminal
setting
BIT5:S6 virtual terminal
BIT6:S7 virtual terminal
BIT7:S8 virtual terminal
BIT8:HDI virtual terminal
Set the operation mode of the terminals control
0:2-wire control 1, comply the enable with the
direction. This mode is widely used. It determines
the rotation direction by the defined FWD and
REV terminals command.
Terminals FWD REV
Running
command
control FWD
P05.13 K1 OFF OFF Stopping 0 ◎
running
Forward
mode REV ON OFF
running
K2
Reverse
OFF ON
running
COM
ON ON Hold on

1:2-wire control 2; Separate the enable from the

direction. FWD defined by this mode is the

53
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
enabling ones. The direction depends on the
state of the defined REV.

2:3-wire control 1; Sin is the enabling terminal on

this mode, and the running command is caused
by FWD and the direction is controlled by REV.
Sin is natural closed.

The direction control is as below during

operation:
Previous Current
Sln REV
direction direction
Forward Reverse
ON OFF→ON
Reverse Forward
Reverse Forward
ON ON→OFF
Forward Reverse
ON→ ON
Decelerate to stop
OFF OFF
3:3-wire control 2; Sin is the enabling terminal on
this mode, and the running command is caused
by SB1 or SB3 and both of them control the
running direction.NC SB2 generates the stop
command.

54
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
SB1

FWD
SB2
SIn

REV
SB3

COM

Sln FWD REV Direction

OFF→ ON Forward
ON
ON OFF Reverse

ON OFF→ Forward
ON
OFF ON Reverse

ON→ Decelerat
OFF e to stop

Note: for the 2-wire running mode, when

FWD/REV terminal is valid, the inverter stop
because of the stopping command from other
sources, even the control terminal FWD/REV
keeps valid; the inverter won’t work when the
stopping command is canceled. Only when
FWD/REV is relaunched, the inverter can start
again. For example, the valid STOP/RST stop
when PLC signal cycles stop, fixed-length stop
and terminal control (see P07.04).
S1 terminal
P05.14 switching-on 0.000s ○
delay time
S1 The function code defines the corresponding
terminal delay time of electrical level of the programmable
P05.15 0.000s ○
switching-off terminals from switching on to switching off.
delay time
S2 terminal
P05.16 switching-on 0.000s ○
delay time
S2 Setting range:0.000~50.000s
terminal
P05.17 0.000s ○
switching-off
delay time

55
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
S3 terminal
P05.18 switching-on 0.000s ○
delay time
S3
terminal
P05.19 0.000s ○
switching-off
delay time
S4 terminal
P05.20 switching-on 0.000s ○
delay time
S4
terminal
P05.21 0.000s ○
switching-off
delay time
S5
terminal
P05.22 0.000s ○
switching-on
delay time
S5
terminal
P05.23 0.000s ○
switching-off
delay time
S6
terminal
P05.24 0.000s ○
switching-on
delay time
S6
terminal
P05.25 0.000s ○
switching-off
delay time
S7
terminal
P05.26 0.000s ○
switching-on
delay time
S7
terminal
P05.27 0.000s ○
switching-off
delay time
S8
P05.28 terminal 0.000s ○
switching-on
56
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
delay time
S8
terminal
P05.29 0.000s ○
switching-off
delay time
HDI
terminal
P05.30 0.000s ○
switching-on
delay time
HDI
terminal
P05.31 0.000s ○
switching-off
delay time
Lower limit of The inverter(≤15kW) can be set by the analog
P05.32 0.00V ○
AI1 potentiometer on the keypad and AI1 setting is
Correspondin not available for the device which is 18.5kW or
g setting of higer than 18.5 kW.
P05.33 0.0% ○
the lower The function code defines the relationship
limit of AI1 between the analog input voltage and its
Upper limit of corresponding set value. If the analog input
P05.34 10.00V ○
AI1 voltage beyond the set minimum or maximum
Correspondin input value, the inverter will count at the minimum
g setting of or maximum one.
P05.35 100.0% ○
the upper When the analog input is the current input, the
limit of AI1 corresponding voltage of 0~20mA is 0~10V.
AI1 input In different cases, the corresponding rated value
P05.36 0.100s ○
filter time of 100.0% is different. See the application for
Lower limit of detailed information.
P05.37 The figure below illustrates different applications: 0.00V ○
AI2
Correspondin
g setting of
P05.38 0.0% ○
the lower
limit of AI2
Upper limit of
P05.39 10.00V ○
AI2
Correspondin
g setting of
P05.40 100.0% ○
the upper Input filter time: this parameter is used to adjust
limit of AI2 the sensitivity of the analog input. Increasing the
P05.41 AI2 input 0.100s ○

57
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
filter time value properly can enhance the anti-interference
Lower limit of of the analog, but weaken the sensitivity of the
P05.42 -10.00V ○
AI3 analog input
Correspondin Note: Analog AI1 and AI2 can support 0~10V or
g setting of 0~20mA input, when AI1 and AI2 selects 0~20mA
P05.43 -100.0% ○
the lower input, the corresponding voltage of 20mA is 5V.
limit of AI3 AI3 can support the output of -10V~+10V.
Middle value The setting range of P05.32:0.00V~P05.34
P05.44 The setting range of P05.33:-100.0%~100.0% 0.00V ○
of AI3
Correspondin The setting range of P05.34:P05.32~10.00V
g middle The setting range of P05.35:-100.0%~100.0%
P05.45 0.0% ○
setting of The setting range of P05.36:0.000s~10.000s
AI3 The setting range of P05.37:0.00V~P05.39
Upper limit of The setting range of P05.38:-100.0%~100.0%
P05.46 The setting range of P05.39:P05.37~10.00V 10.00V ○
AI3
Correspondin The setting range of P05.40:-100.0%~100.0%
The setting range of P05.41:0.000s~10.000s
g setting of
P05.47 100.0% ○
the upper The setting range of P05.42:-10.00V~P05.44
limit of AI3 The setting range of P05.43:-100.0%~100.0%
The setting range of P05.44: P05.42~P05.46
The setting range of P05.45:-100.0%~100.0%
AI3 input The setting range of P05.46:P05.44~10.00V
P05.48 0.100s ○
filter time The setting range of P05.47:-100.0%~100.0%
The setting range of P05.48:0.000s~10.000s
The function selection when HDI terminals is
high-speed pulse input
0:Frequency setting input, frequency setting
HDI
source
P05.49 high-speed 0 ◎
1:Counter input, high-speed pulse counter input
pulse input
terminals
2:Length counting input, length counter input
terminals
Lower limit
0.000
P05.50 frequency of 0.000kHz~P05.52 ○
kHz
HDI
Correspondin
g setting of
P05.51 HDI low -100.0%~100.0% 0.0% ○
frequency
setting

58
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
Upper limit
50.00
P05.52 frequency of P05.50 ~50.00kHz ○
kHz
HDI
Correspondin
g setting of
P05.53 upper limit -100.0%~100.0% 100.0% ○
frequency of
HDI
HDI
frequency
P05.54 0.000s~10.000s 0.100s ○
input filter
time
P06 Group Output terminals
The function selection of the high-speed pulse
output terminals.
0: Open collector pole high speed pulse output:
The Max.pulse frequency is 50.0kHz. See
P06.00 HDO output 0 ◎
P06.27~P06.31 for detailed information of the
related functions.
1: Open collector pole output. See P06.02 for
detailed information of the related functions.
P06.01 Y1 output 0:Invalid 0 ○
P06.02 HDO output 1:In operation 0 ○
Relay RO1 2:Forward rotation
P06.03 1 ○
output 3:Reverse rotation
4: Jogging
5:The inverter fault
6:Frequency degree test FDT1
7:Frequency degree test FDT2
8:Frequency arrival
9:Zero speed running
10:Upper limit frequency arrival
Relay RO2
P06.04 11:Lower limit frequency arrival 5 ○
output
12:Ready for operation
13:Pre-magnetizing
14:Overload pre-alarm
15: Underload pre-alarm
16:Completion of simple PLC step
17:Completion of simple PLC cycle
18:Setting count value arrival

59
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
19:Defined count value arrival
20:External fault valid
21:Length arrival
22:Running time arrival
23:MODBUS communication virtual terminals
output
26: DC bus voltage establishment
27: Auxiliary motor 1
28: Auxiliary motor 2
The function code is used to set the pole of the
output terminal.
When the current bit is set to 0, input terminal is
Polarity
positive.
selection of
P06.05 When the current bit is set to 1, input terminal is 0 ○
output
negative.
terminals
BIT0 BIT1 BIT2 BIT3
Y HDO RO1 RO2
Setting range:0~F
Y1
P06.06 switching-on 0.000s ○
delay time
Y1
P06.07 switching-off 0.000s ○
delay time
HDO The function code defines the corresponding
P06.08 switching-on delay time of the electrical level change during 0.000s ○
delay time the programmable terminal switching on and off.
HDO
P06.09 switching-off 0.000s ○
delay time
RO1
P06.10 switching-on The setting range :0.000~50.000s 0.000s ○
delay time Note: P06.08 and P06.09 are valid only when
RO1 P06.00=1.
P06.11 switching-off 0.000s ○
delay time
RO2
P06.12 switching-on 0.000s ○
delay time
P06.13 RO2 0.000s ○

60
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
switching-off
delay time
P06.14 AO1 output 0:Running frequency 0 ○
P06.15 AO2 output 1:Setting frequency 0 ○
2:Ramp reference frequency
3:Running rotation speed
4:Output current
(relative to twice the inverter rated current)
5:Output current
(relative to twice the motor rated current)
6:Output voltage
7:Output power
9:Output torque
HDO
10:Analog AI1 input value (The inverter(≤15kW)
high-speed
P06.16 can be set by the analog potentiometer on the 0 ○
pulse output
keypad and AI1 setting is not available for the
selection
device which is 18.5kW or higer than 18.5 kW)
11:Analog AI2 input value
12:Analog AI3 input value
13:High speed pulse HDI input value
14:MODBUS communication set value 1
15:MODBUS communication set value 2
22: Torque current
(relative to triple the motor rated current)
23: Ramp reference frequency(with sign)
Lower limit of
P06.17 0.0% ○
AO1 output
Correspondin The above function codes define the relative
g AO1 output relationship between the output value and analog
P06.18 0.00V ○
to the lower output. When the output value exceeds the range
limit of set maximum or minimum output, it will count
Upper limit of according to the low-limit or upper-limit output.
P06.19 100.0% ○
AO1 output When the analog output is current output, 1mA
The equals to 0.5V.
correspondin In different cases, the corresponding analog
P06.20 g AO1 output output of 100% of the output value is different. 10.00V ○
to the upper Please refer to each application for detailed
limit information.
AO1 output
P06.21 0.000s ○
filter time

61
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
A
Lower limit of O
P06.22 10V (20m A) 0.0% ○
AO2 output
Correspondin
g AO2 output
P06.23 0.00V ○
to the lower
limit
0.0% 100.0%
Upper limit of
P06.24 Setting range of P06.18 0.00V~10.00V 100.0% ○
AO2 output
Setting range of P06.19 P06.17~100.0%
Correspondin
Setting range of P06.20 0.00V~10.00V
g AO2 output
P06.25 Setting range of P06.21 0.000s~10.000s 10.00V ○
to the upper
Setting range of P06.22 0.0%~P06.24
limit
Setting range of P06.23 0.00V~10.00V
AO2 output
P06.26 Setting range of P06.24 P06.22~100.0% 0.000s ○
filter time
Setting range of P06.25 0.00V~10.00V
Lower limit of
P06.27 Setting range of P06.26 0.000s~10.000s 0.00% ○
HDO output
Setting range of P06.27 0.000s~10.000s
Correspondin
Setting range of P06.28 0.00~50.00kHz
g HDO
P06.28 Setting range of P06.29 P06.27~100.0% 0.00kHz ○
output to the
Setting range of P06.30 0.00~50.00kHz
lower limit
Setting range of P06.31 0.000s~10.000s
Upper limit of
P06.29 100.0% ○
HDO output
Correspondin
g HDO 50.00
P06.30 ○
output to the kHz
upper limit
HDO output
P06.31 0.000s ○
filter time
P07 Group Human-Machine Interface
0~65535
The password protection will be valid when
setting any non-zero number.
00000: Clear the previous user’s password, and
make the password protection invalid.
User’s
P07.00 After the user’s password becomes valid, if the 0 ○
password
password is incorrect, users cannot enter the
parameter menu. Only correct password can
make the user check or modify the parameters.
Please remember all users’ passwords.
Retreat editing state of the function codes and

62
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
the password protection will become valid in 1
minute. If the password is available, press
PRG/ESCto enter into the editing state of the
function codes, and then “0.0.0.0.0” will be
displayed. Unless input right password, the
operator can not enter into it.
Note: Restoring to the default value can clear the
password, please use it with caution.
The function code determines the mode of
parameters copy.
0:No operation
1:Upload the local function parameter to the
keypad
2:Download the keypad function parameter to
local address(including the motor parameters)
3:Download the keypad function parameter to
Parameter
P07.01 local address (excluding the motor parameter of 0 ◎
copy
P02 group)
4:Download the keypad function parameters to
local address (only for the motor parameter of
P02 group)
Note: After completing the 1~4 operation, the
parameter will come back to 0 automatically, the
function of upload and download excludes the
factory parameters of P29.
0:No function
1: Jogging. Press QUICK/JOG to begin the
jogging running.
2: Shift the display state by the shifting key.
Press QUICK/JOGto shift the displayed function
code from right to left.
3: Shift between forward rotations and reverse
QUICK/JOG
rotations. Press QUICK/JOG to shift the direction
P07.02 function 1 ◎
of the frequency commands. This function is only
selection
valid in the keypad commands channels.
4: Clear UP/DOWN settings. Press QUICK/JOG
to clear the set value of UP/DOWN.
5: Coast to stop. Press QUICK/JOG to coast to
stop.
6: Shift the running commands source. Press
QUICK/JOG to shift the running commands
63
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
source.
7:Quick commission mode(committee according
to the non-factory parameter)
Note: Press QUICK/JOGto shift between
forward rotation and reverse rotation, the inverter
does not record the state after shifting during
powering off. The inverter will run according to
parameter P00.13 during next powering on.
When P07.02=6, set the shifting sequence of
Shifting running command channels.
sequence 0:Keypad control→terminals control
P07.03 selection of →communication control 0 ○
QUICK/JOG 1:Keypad control←→terminals control
commands 2:Keypad control←→communication control
3:Terminals control←→communication control
STOP/RST is valid for stop function. STOP/RST
is valid in any state for the fault reset.
0:Only valid for the keypad control
STOP/RST
P07.04 1:Both valid for keypad and terminals control 0 ○
stop function
2:Both valid for keypad and communication
control
3:Valid for all control modes
0x0000~0xFFFF
BIT0:running frequency (Hz on)
BIT1:set frequency(Hz flickering)
BIT2:bus voltage (Hz on)
BIT3:output voltage(V on)
BIT4:output current(A on)
BIT5:running rotation speed (rpm on)
BIT6:output power(% on)
Parameters BIT7:output torque(% on)
P07.05 0x03FF ○
state 1 BIT8:PID reference(% flickering)
BIT9:PID feedback value(% on)
BIT10:input terminals state
BIT11:output terminals state
BIT12:torque set value(% on)
BIT13:pulse counter value
BIT14:length value
BIT15:PLC and the current stage in multi-step
speed
P07.06 Parameters 0x0000~0xFFFF 0x0000
64
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
state 2 BIT0: AI1 (V on) (The inverter(≤15kW) can be
set by the analog potentiometer on the keypad
and AI1 setting is not available for the device
which is 18.5kW or higer than 18.5 kW)
BIT1: AI2 (V on)
BIT2: AI3 (V on)
BIT3: HDI frequency
BIT4: motor overload percentage (% on)
BIT5: the inverter overload percentage (% on)
BIT6: ramp frequency given value(Hz on)
BIT7: linear speed
BIT8: AC inlet current (A on)
BIT9: upper limit frequency (Hz on)
0x0000~0xFFFF
BIT0:set frequency
(Hz on, frequency flickering slowly)
BIT1:bus voltage (V on)
BIT2:input terminals state
BIT3:output terminals state
BIT4:PID reference (% flickering)
BIT5:PID feedback value(% flickering)
BIT6:reserved
The BIT7:analog AI1 value(V on) (The inverter(≤
P07.07 parameter in 15kW) can be set by the analog potentiometer on 0x00FF ○
the stop state the keypad and AI1 setting is not available for the
device which is 18.5kW or higer than 18.5 kW)
BIT8:analog AI2 value(V on)
BIT9: analog AI3 value(V on)
BIT10:high speed pulse HDI frequency
BIT11:PLC and the current step in multi-step
speed
BIT12:pulse counters
BIT13:length value
BIT14: upper limit frequency (Hz on)
Frequency 0.01~10.00
P07.08 1.00 ○
coefficient Displayed frequency=running frequency* P07.08
Rotation 0.1~999.9%
P07.09 speed Mechanical rotation speed =120*displayed 100.0% ○
coefficient running frequency×P07.09/motor pole pairs
Linear speed 0.1~999.9%
P07.10 1.0% ○
coefficient Linear speed= Mechanical rotation
65
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
speed×P07.10
Rectifier
bridge
P07.11 0~100.0℃ ●
module
temperature
Converter
P07.12 module 0~100.0℃ ●
temperature
Software
P07.13 1.00~655.35 ●
version
Local
P07.14 accumulative 0~65535h ●
running time
High bit of
Display the power used by the inverter.
P07.15 power ●
The power consumption of the inverter
consumption
=P07.15*1000+P07.16
Low bit of
Setting range of P07.15: 0~65535 kWh (*1000)
P07.16 power ●
Setting range of P07.16: 0.0~999.9 kWh
consumption
0: G type
P07.17 Inverter type ●
1: P type
The rated
P07.18 power of the 0.4~3000.0kW ●
inverter
The rated
P07.19 voltage of the 50~1200V ●
inverter
The rated
P07.20 current of the 0.1~6000.0A ●
inverter
Factory bar
P07.21 0x0000~0xFFFF ●
code 1
Factory bar
P07.22 0x0000~0xFFFF ●
code 2
Factory bar
P07.23 0x0000~0xFFFF ●
code 3
Factory bar
P07.24 0x0000~0xFFFF ●
code 4
Factory bar
P07.25 0x0000~0xFFFF ●
code 5

66
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
Factory bar
P07.26 0x0000~0xFFFF ●
code 6

0:No fault
1:IGBT U phase protection(OUt1)
2:IGBT V phase protection(OUt2)
3:IGBT W phase protection(OUt3)
4:OC1
Current fault
P07.27 5:OC2 ●
type
6:OC3
7:OV1
8:OV2
9:OV3
10:UV
11:Motor overload(OL1)
12:The inverter overload(OL2)
13:Input side phase loss(SPI)
14:Output side phase loss(SPO)
15:Overheat of the rectifier module(OH1)
16:Overheat fault of the inverter module(OH2)
Previous fault 17:External fault(EF)
P07.28 18:485 communication fault(CE) ●
type
19:Current detection fault(ItE)
20:Motor antotune fault(tE)
21:EEPROM operation fault(EEP)
22:PID response offline fault(PIDE)
23:Braking unit fault(bCE)
24:Running time arrival(END)
Previous 2
P07.29 25:Electrical overload(OL3) ●
fault type
26:Panel communication fault(PCE)
Previous 3
P07.30 27:Parameter uploading fault (UPE) ●
fault type
28:Parameter downloading fault(DNE)
Previous 4 32:Grounding short circuit fault 1(ETH1)
P07.31 ●
fault type 33:Grounding short circuit fault 2(ETH2)
Previous 5 36: Undervoltage fault(LL)
P07.32 ●
fault type
Running
P07.33 frequency at 0.00Hz ●
current fault
Ramp
P07.34 0.00Hz
reference

67
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
frequency at
current fault
Output
P07.35 voltage at the 0V
current fault
Output
P07.36 current at 0.0A
current fault
Bus voltage
P07.37 at current 0.0V
fault
The Max.
temperature
P07.38 0.0℃
at current
fault
Input
terminals
P07.39 0 ●
state at
current fault
Output ●
terminals
P07.40 0
state at
current fault
Running ●
P07.41 frequency at 0.00Hz
previous fault
Ramp ●
reference
P07.42 0.00Hz
frequency at
previous fault
Output ●
P07.43 voltage at 0V
previous fault
The output ●
P07.44 current at 0.0A
previous fault
Bus voltage ●
P07.45 at previous 0.0V
fault
P07.46 The Max. 0.0℃ ●

68
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
temperature
at previous
fault
Input ●
terminals
P07.47 0
state at
previous fault
Output ●
terminals
P07.48 0
state at
previous fault
Runnig ●
frequency at
P07.49 0.00Hz
previous 2
fault
Output ●
voltage at
P07.50 0.00Hz
previous 2
faults
Output ●
current at
P07.51 0V
previous 2
faults
Output
current at
P07.52 0.0A ●
previous 2
fault
Bus voltage ●
P07.53 at previous 2 0.0V
fault
The Max. ●
temperature
P07.54 0.0℃
at previous 2
fault
Input ●
terminals
P07.55 state at 0
previous 2
fault
Output ●
P07.56 0
terminals
69
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
state at
previous 2
fault
P08 Group Enhanced function
Depend
P08.00 ACC time 2 on ○
model
Depend
P08.01 DEC time 2 on ○
Refer to P00.11 and P00.12 for detailed model
definition. Depend
P08.02 ACC time 3 on ○
Goodrive200A series define four groups of
model
ACC/DEC time which can be selected by P5
Depend
group. The first group of ACC/DEC time is the
P08.03 DEC time 3 on ○
factory default one. model
Setting range:0.0~3600.0s Depend
P08.04 ACC time 4 on ○
model
Depend
P08.05 DEC time 4 on ○
model
This parameter is used to define the reference
Jogging frequency during jogging.
P08.06 5.00Hz ○
frequency Setting range: 0.00Hz ~P00.03
(the Max. frequency)
The jogging ACC time means the time needed if Depend
Jogging ACC
P08.07 the inverter runs from 0Hz to the Max. on ○
time
Frequency. model
The jogging DEC time means the time needed if
Depend
Jogging DEC the inverter goes from the Max. Frequency
P08.08 on ○
time (P0.03) to 0Hz.
model
Setting range:0.0~3600.0s
Jumping
P08.09 When the set frequency is in the range of 0.00Hz ○
frequency 1
jumping frequency, the inverter will run at the
Jumping edge of the jumping frequency.
P08.10 frequency The inverter can avoid the mechanical resonance 0.00Hz ○
range 1 point by setting the jumping frequency. The
Jumping inverter can set three jumping frequency. But this
P08.11 0.00Hz ○
frequency 2 function will be invalid if all jumping points are 0.
Jumping
P08.12 0.00Hz ○
frequency

70
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
range 2
Jumping
P08.13 0.00Hz ○
frequency 3

Jumping
P08.14 frequency 0.00Hz ○
range 3
Setting range: 0.00Hz ~P00.03
(the Max. frequency)
Traverse This function applies to the industries where
P08.15 0.0% ○
range traverse and convolution function are required
Sudden such as textile and chemical fiber.
jumping The traverse function means that the output
P08.16 0.0% ○
frequency frequency of the inverter is fluctuated with the set
range frequency as its center. The route of the running
Traverse frequency is illustrated as below, of which the
P08.17 5.0s ○
boost time traverse is set by P08.15 and when P08.15 is set
as 0, the traverse is 0 with no function.

Traverse range: The traverse running is limited

by upper and low frequency.
The traverse range relative to the center
Traverse
frequency: traverse range AW＝center frequency
P08.18 declining 5.0s ○
×traverse range P08.15.
time
Sudden jumping frequency＝traverse range AW
×sudden jumping frequency range P08.16.
When run at the traverse frequency, the value
which is relative to the sudden jumping
frequency.
The raising time of the traverse frequency: The
time from the lowest point to the highest one.
The declining time of the traverse frequency: The
time from the highest point to the lowest one.
The setting range of P08.15: 0.0~100.0%
(relative to the set frequency)
71
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
The setting range of P08.16: 0.0~50.0%
(relative to the traverse range)
The setting range of P08.17: 0.1~3600.0s
The setting range of P08.18: 0.1~3600.0s
Setting The counter works by the input pulse signals of
P08.25 counting the HDI terminals. 0 ○
value When the counter achieves a fixed number, the
multi-function output terminals will output the
signal of “fixed counting number arrival” and the
counter go on working; when the counter
achieves a setting number, the multi-function
output terminals will output the signal of “setting
counting number arrival”, the counter will clear all
numbers and stop to recount before the next
pulse.
Reference The setting counting value P08.26 should be no
P08.26 counting more than the setting counting value P08.25. 0 ○
value The function is illustrated as below:

Setting range of P08.25:P08.26~65535

Setting range of P08.26:0~P08.25
Pre-set running time of the inverter. When the
accumulative running time achieves the set time,
Set running
P08.27 the multi-function digital output terminals will 0m ○
time
output the signal of “running time arrival”.
Setting range:0~65535 min
Fault reset
The time of the fault reset: set the fault reset time
P08.28 0 ○
times by selecting this function. If the reset time
exceeds this set value, the inverter will stop for
the fault and wait to be repaired.
Interval time The interval time of the fault reset: The interval
P08.29 of automatic between the time when the fault occurs and the 1.0s ○
fault reset time when the reset action occurs.
Setting range of P08.28:0~10
Setting range of P08.29:0.1~3600.0s
P08.30 Frequency The output frequency of the inverter changes as 0.00Hz ○

72
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
decreasing the load. And it is mainly used to balance the
ratio of the power when several inverters drive one load.
dropping Setting range:0.00~10.00Hz
control
FDT1 When the output frequency exceeds the
electrical corresponding frequency of FDT electrical level,
50.00
P08.32 level the multi-function digital output terminals will ○
Hz
detection output the signal of “frequency level detect FDT”
value until the output frequency decreases to a value
FDT1 lower than (FDT electrical level—FDT retention
retention detection value) the corresponding frequency,
P08.33 5.0% ○
detection the signal is invalid. Below is the waveform
value diagram:
FDT2
electrical
50.00
P08.34 level ○
Hz
detection
value

FDT2 Setting range of P08.32: 0.00Hz~P00.03

retention (the Max. frequency)
P08.35 Setting range of P08.33: -100.0~100.0% 5.0% ○
detection
value (FDT1 electrical level)
Setting range of P08.34: 0.00 Hz ~P00.03
(the Max. frequency)
Setting range of P08.35: 0.0~100.0%
(FDT2 electrical level)
When the output frequency is among the below
Frequency
or above range of the set frequency, the
arrival
P08.36 multi-function digital output terminal will output 0.00Hz ○
detection
the signal of “frequency arrival”, see the diagram
value
below for detailed information:

73
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value

The setting range:0.00Hz~P00.03

(the Max. frequency)
This parameter is used to control the internal
braking unit.
Energy 0:Disable
P08.37 braking 1:Enable 0 ○
enable Note: Only applied to internal braking unit. After
enabling, the overvoltage stall point will increase
by 20V more than the energy braking point.
380V
After setting the original bus voltage, adjust this
voltage:
parameter to break the load appropriately. The
700.0V
factory value changes with voltage level.
500V
Threshold The setting range:200.0~2000.0V
P08.38 voltage: ○
voltage In order to prevent customers set the value is too
900.0V
large, it is recommended setting range:
660V
voltage 380V 500V 660
voltage:
range 685~750V 860~950V 1080~1180V
1120.0V
Set the operation mode of the cooling fan.
0: Normal mode, after the rectifier receives
operation command or the detected temperature
Cooling fan
of module is above 45℃ or the module current is
P08.39 running 0 ○
above 20% of the rated current, the fan rotates.
mode
1:The fan keeps on running after power on
(generally for the site with high temperature and
humidity)
0x00~0x21
LED ones: PWM mode selection ◎
PWM 0: PWM mode 1, three-phase modulation and
P08.40 00
selection two-modulation
1: PWM mode 2, three-phase modulation
LED tens: low-speed carrier frequency limit mode

74
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
0: Low-speed carrier frequency limit mode 1, the
carrier frequency will limit to 2k if it exceeds 2k at
low speed
1:Low-speed carrier frequency limit mode 2, the
carrier frequency will limit to 4k if it exceeds 4k at
low speed
2: No limit
0x00~0x11
LED ones ◎
Over 0: Invalid
P08.41 commission 1: Valid 0x01
selection LED tens
0: Light overcommission
1: Heavy overcommission
0x000~0x1223
LED ones:frequency enable selection
0:Both ∧/∨ keys and digital potentiometer
adjustments are valid
1:Only ∧/∨ keys adjustment is valid
2:Only digital potentiometer adjustments is valid
3:Neither ∧/∨ keys nor digital potentiometer
adjustments are valid
LED tens: frequency control selection
0:Only valid when P00.06=0 or P00.07=0
Keypad data 1:Valid for all frequency setting manner
P08.42 0x0000 ○
control 2:Invalid for multi-step speed when multi-step
speed has the priority
LED hundreds: action selection during stopping
0:Setting is valid
1:Valid during running, cleared after stopping
2:Valid during running, cleared after receiving the
stop command
LED thousands: ∧/∨ keys and digital
potentiometer integral function
0:The integral function is valid
1:The integral function is invalid
Integral ratio
of the keypad
P08.43 0.01~10.00s 0.10s ○
potentiomete
r
P08.44 UP/DOWN 0x00~0x221 0x000 ○
75
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
terminals LED ones: frequency control selection
control 0:UP/DOWN terminals setting valid
1:UP/DOWN terminals setting valid
LED tens: frequency control selection
0:Only valid when P00.06=0 or P00.07=0
1:All frequency means are valid
2:When the multi-step are priority, it is invalid to
the multi-step
LED hundreds: action selection when stop
0:Setting valid
1: Valid in the running, clear after stop
2: Valid in the running, clear after receiving the
stop commands
UP terminals
frequency 0.50
P08.45 0.01~50.00Hz/s ○
increasing Hz/s
integral ratio
DOWN
terminals 0.50
P08.46 0.01~50.00 Hz/s ○
frequency Hz/s
integral ratio
0x000~0x111
LED ones: Action selection when power off.
0:Save when power off
1:Clear when power off
LED tens: Action selection when MODBUS set
Action when
frequency off
P08.47 the frequency 0x000 ○
0:Save when power off
setting is off
1:Clear when power off
LED hundreds:The action selection when other
frequency set frequency off
0:Save when power off
1:Clear when power off
High bit of This parameter is used to set the original value of
P08.48 initial power the power consumption. 0° ○
consumption The original value of the power consumption
Low bit of =P08.48*1000+ P08.49
P08.49 initial power Setting range of P08.48: 0~59999 kWh (k) 0.0° ○
consumption Setting range of P08.49:0.0~999.9 kWh
Magnetic flux This function code is used to enable magnetic
P08.50 0 ●
braking flux.
76
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
0: Invalid.
100~150: The bigger the coefficient, the stronger
the braking is.
This inverter is used to increase the magnetic flux
to decelerate the motor. The energy generated
by the motor during braking can be converter into
heat energy by increasing the magnetic flux.
The inverter monitors the state of the motor
continuously even during the magnetic flux
period. So the magnetic flux can be used in the
motor stop, as well as to change the rotation
speed of the motor. Its other advantages are:
Brake immediately after the stop command. It
does not need to wait the magnetic flux weaken.
Better cooling for motors. The current of the
stator other than the rotor increases during
magnetic flux braking, while the cooling of the
stator is more effective than the rotor.
Input power This function code is used to adjust the displayed
P08.51 factor of the current of the AC input side. 0.56 ○
inverter Setting range:0.00~1.00
P09 Group PID control
When the frequency command selection
(P00.06, P00. 07) is 7 or the voltage setting
channel selection (P04.27) is 6, the running
mode of the inverter is procedure PID controlled.
The parameter determines the target reference
channel during the PID procures.
0:Keypad digital reference(P09.01)
1:Analog channel AI1 reference (The inverter
PID (≤15kW) can be set by the analog potentiometer
P09.00 reference on the keypad and AI1 setting is not available for 0 ○
source the device which is 18.5kW or higer than 18.5kW)
2:Analog channel AI2 reference
3:Analog channel AI3 set
4:High speed pulse HDI set
5:Multi-step speed set
6:MODBUS communication set
The setting target of procedure PID is a relative
one, 100% of the setting equals to 100% of the
response of the controlled system.
77
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
The system is calculated according to the relative
value (0~100.0%).
Note:
Multi-step speed reference, it is realized by
setting P10 group parameters.
When P09.00=0, set the parameter whose basic
Keypad PID
P09.01 value is the feedback value of the system. 0.0% ○
preset
The setting range:-100.0%~100.0%
Select the PID channel by the parameter.
0:Analog channel AI1 feedback (The inverter(≤
15kW) can be set by the analog potentiometer on
the keypad and AI1 setting is not available for the
device which is 18.5kW or higer than 18.5 kW)
PID feedback 1:Analog channel AI2 feedback
P09.02 0 ○
source 2:Analog channel AI3 feedback
3:High speed HDI feedback
4:MODBUS communication feedback
Note: The reference channel and the feedback
channel can not coincide, otherwise, PID can not
control effectively.
0: PID output is positive: When the feedback
signal exceeds the PID reference value, the
output frequency of the inverter will decrease to
balance the PID. For example, the strain PID
PID output control during wrap-up
P09.03 0 ○
feature 1: PID output is negative: When the feedback
signal is stronger than the PID reference value,
the output frequency of the inverter will increase
to balance the PID. For example, the strain PID
control during wrap-down
The function is applied to the proportional gain P
of PID input.
P determines the strength of the whole PID
adjuster. The parameter of 100 means that when
Proportional
P09.04 the offset of PID feedback and reference value is 1.00 ○
gain (Kp)
100%, the adjusting range of PID adjustor is the
Max. Frequency (ignoring integral function and
differential function).
The setting range:0.00~100.00
Integral This parameter determines the speed of PID
P09.05 0.10s ○
time(Ti) adjustor to carry out integral adjustment on the
78
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
deviation of PID feedback and reference.
When the deviation of PID feedback and
reference is 100%, the integral adjustor works
continuously after the time (ignoring the
proportional effect and differential effect) to
achieve the Max. Frequency (P00.03) or the
Max. Voltage (P04.31). Shorter the integral time,
stronger is the adjustment
Setting range: 0.01~10.00s
This parameter determines the strength of the
change ratio when PID adjustor carries out
integral adjustment on the deviation of PID
feedback and reference.
If the PID feedback changes 100% during the
Differential
P09.06 time, the adjustment of integral adjustor (ignoring 0. 00s ○
time(Td)
the proportional effect and differential effect) is
the Max. Frequency (P00.03) or the Max. Voltage
(P04.31). Longer the integral time, stronger is the
adjusting.
Setting range: 0.00~10.00s
This parameter means the sampling cycle of the
feedback. The modulator calculates in each
Sampling
P09.07 sampling cycle. The longer the sapling cycle is, 0.100s ○
cycle(T)
the slower the response is.
Setting range: 0.000~10.000s
The output of PID system is relative to the
maximum deviation of the close loop reference.
As shown in the diagram below, PID adjustor
stops to work during the deviation limit. Set the
function properly to adjust the accuracy and
stability of the system.

PID control
P09.08 0.0% ○
deviation limit

Setting range:0.0~100.0%

79
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
Output upper These parameters are used to set the upper and
P09.09 100.0% ○
limit of PID lower limit of the PID adjustor output.
100.0 % corresponds to Max. frequency or the
Output lower Max. voltage of ( P04.31)
P09.10 0.0% ○
limit of PID Setting range of P09.09: P09.10~100.0%
Setting range of P09.10: -100.0%~P09.09
Feedback Set the PID feedback offline detection value,
offline when the detection value is smaller than or equal
P09.11 0.0% ○
detection to the feedback offline detection value, and the
value lasting time exceeds the set value in P09.12, the
inverter will report “PID feedback offline fault” and
the keypad will display PIDE.

Feedback
offline
P09.12 1.0s ○
detection
time

Setting range of P09.11: 0.0~100.0%

Setting range of P09.12: 0.0~3600.0s
0x0000~0x1111
LED ones:
0: Keep on integral adjustment when the
frequency achieves the upper and low limit; the
integration shows the change between the
reference and the feedback unless it reaches the
internal integral limit. When the trend between
the reference and the feedback changes, it
needs more time to offset the impact of
PID continuous working and the integration will
P09.13 0x0001 ○
adjustment change with the trend.
1: Stop integral adjustment when the frequency
achieves the upper and low limit. If the integration
keeps stable, and the trend between the
reference and the feedback changes, the
integration will change with the trend quickly.
LED tens: P00.08 is 0
0: The same with the setting direction; if the
output of PID adjustment is different from the
current running direction, the internal will output 0
80
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
forcedly.
1:Opposite to the setting direction
LED hundreds: P00.08 is 0
0: Limit to the maximum frequency
1: Limit to frequency A
LED thousands:
0:A+B frequency, the buffer of A frequency is
invalid
1:A+B frequency, the buffer of A frequency is
valid
ACC/DEC is determined by ACC time 4 of
P08.04
Proportional
gain at low
P09.14 0.00~100.00 1.00 ○
frequency
(Kp)

PID
command of
P09.15 0.0~1000.0s 0.0s ○
ACC/DEC
time

PID output
P09.16 0.000~10.000s 0.000s ○
filter time
P10 Group Simple PLC and multi-step speed control
0: Stop after running once. The inverter has to be
commanded again after finishing a cycle.
1: Run at the final value after running once. After
finish a signal, the inverter will keep the running
P10.00 Simple PLC 0 ○
frequency and direction of the last run.
2: Cycle running. The inverter will keep on
running until receiving a stop command and then,
the system will stop.
0: Power loss without memory
Simple PLC
P10.01 1:Power loss memory；PLC record the running 0 ○
memory
step and frequency when power loss.
Multi-step
100.0% of the frequency setting corresponds to
P10.02 0.0% ○
speed 0 the Max. frequency P00.03.
The running When selecting simple PLC running, set
P10.03 time of step P10.02~P10.33 to define the running frequency 0.0s ○
0 and direction of all steps.

81
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
Multi-stepNote: The symbol of multi-step determines the
P10.04 0.0% ○
speed 1 running direction of simple PLC. The negative
The running value means reverse rotation.
P10.05 0.0s ○
time of step 1
Multi-step
P10.06 0.0% ○
speed 2
The running
P10.07 0.0s ○
time of step 2
Multi-step
P10.08 0.0% ○
speed 3
The running Multi-step speeds are in the range of --fmax~fmax
P10.09 0.0s ○
time of step 3 and it can be set continuously.
Multi-step Goodrive200A series inverters can set 16 steps
P10.10 speed, selected by the combination of multi-step 0.0% ○
speed 4
The running terminals 1~4, corresponding to the speed 0 to
P10.11 0.0s ○
time of step 4 speed 15.
Multi-step
P10.12 0.0% ○
speed 5
The running
P10.13 0.0s ○
time of step 5
Multi-step
P10.14 0.0% ○
speed 6
The running
P10.15 0.0s ○
time of step 6
Multi-step
P10.16 0.0% ○
speed 7
The running
P10.17 0.0s ○
time of step 7 When S1=S2=S3=S4=OFF, the frequency input
Multi-step manner is selected via code P00.06 or P00.07.
P10.18 When all S1=S2=S3=S4 terminals aren’t off, it 0.0% ○
speed 8
The running runs at multi-step which takes precedence of
P10.19 0.0s ○
time of step 8 keypad, analog value, high-speed pulse, PLC,
Multi-step communication frequency input. Select at most
P10.20 16 steps speed via the combination code of S1, 0.0% ○
speed 9
S2, S3, and S4.
The running
P10.21 The start-up and stopping of multi-step running is 0.0s ○
time of step 9
determined by function code P00.06, the
Multi-step
P10.22 relationship between S1,S2,S3,S4 terminals and 0.0% ○
speed 10
multi-step speed is as following:
The running
P10.23 S1 OFF ON OFF ON OFF ON OFF ON 0.0s ○
time of step

82
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
10 S2 OFF OFF ON ON OFF OFF ON ON
Multi-step S3 OFF OFF OFF OFF ON ON ON ON
P10.24 0.0% ○
speed 11 S4 OFF OFF OFF OFF OFF OFF OFF OFF
The running Step 0 1 2 3 4 5 6 7
P10.25 time of step S1 OFF ON OFF ON OFF ON OFF ON 0.0s ○
11 S2 OFF OFF ON ON OFF OFF ON ON
Multi-step S3 OFF OFF OFF OFF ON ON ON ON
P10.26 0.0% ○
speed 12 S4 ON ON ON ON ON ON ON ON
The running Step 8 9 10 11 12 13 14 15
P10.27 time of step Setting range of P10.(2n,1<n<17): 0.0s ○
12 -100.0~100.0%
Multi-step Setting range of
P10.28 0.0% ○
speed 13 P10.(2n+1,1<n<17):0.0~6553.5s(min)
The running
P10.29 time of step 0.0s ○
13
Multi-step
P10.30 0.0% ○
speed 14
The running
P10.31 time of step 0.0s ○
14
Multi-step
P10.32 0.0% ○
speed 15
The running
P10.33 time of step 0.0s ○
15
Simple PLC Below is the detailed instruction:
0~7 step Functio ACC/DE ACC/DE ACC/DE ACC/DE
P10.34 Binary bit Step 0x0000 ○
ACC/DEC n code C0 C1 C2 C3

time BIT1 BIT0 0 00 01 10 11

BIT3 BIT2 1 00 01 10 11

BIT5 BIT4 2 00 01 10 11

Simple PLC BIT7 BIT6 3 00 01 10 11

8~15 step P10.34
P10.35 BIT9 BIT8 4 00 01 10 11 0x0000 ○
ACC/DEC
time BIT11 BIT10 5 00 01 10 11

BIT13 BIT12 6 00 01 10 11

BIT15 BIT14 7 00 01 10 11

83
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
BIT1 BIT0 8 00 01 10 11

BIT3 BIT2 9 00 01 10 11

BIT5 BIT4 10 00 01 10 11

BIT7 BIT6 11 00 01 10 11
P10.35
BIT9 BIT8 12 00 01 10 11

BIT11 BIT10 13 00 01 10 11

BIT13 BIT12 14 00 01 10 11

BIT15 BIT14 15 00 01 10 11

After the users select the corresponding

ACC/DEC time, the combined 16 binary bits will
change into decimal bit, and then set the
corresponding function codes.
Setting range: 0x0000~0xFFFF
0: Restart from the first step; stop during running
(cause by the stop command, fault or power
loss), run from the first step after restart.
1: Continue to run from the stop frequency; stop
P10.36 PLC restart during running(cause by stop command and 0 ◎
fault), the inverter will record the running time
automatically, enter into the step after restart and
keep the remaining running at the setting
frequency.
0: Seconds; the running time of all steps is
Multi-step counted by second
P10.37 0 ◎
time unit 1: Minutes; the running time of all steps is
counted by minute
P11 Group Protective parameters
0x00~0x11
LED ones:
0: Input phase loss protection disable
1: Input phase loss protection enable
Phase loss LED tens:
P11.00 111 ○
protection 0: Output phase loss protection disable
1: Output phase loss protection enable
LED hundreds:
0: Input phase loss hardware protection disable
1: Input phase loss hardware protection enable

84
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
Sudden
power loss 0: Disable
P11.01 0 ○
frequency 1: Enable
decrease
Setting range: 0.00Hz/s~P00.03(max. frequency)
After the power loss of the grid, the bus voltage
drops to the sudden frequency-decreasing point,
the inverter begin to decrease the running
frequency at P11.02, to make the inverter
generate power again. The returning power can
maintain the bus voltage to ensure a rated
running of the inverter until power recovery.
Frequency
Voltage degree 220V 380V 660V
decrease
Frequency decrease 10.00
P11.02 ratio of ○
point at sudden power 260V 460V 800V Hz/s
sudden
loss
power loss
Note:
1. Adjust the parameter properly to avoid the
stopping caused by inverter protection during the
switching of the grid.
2. Disable input phase loss protection to enable
this function.
0:Disable
1:Enable

Overvoltage
P11.03 stall 1 ○
protection

Protection
voltage at 120~150%(standard bus voltage) (380V) 136%
P11.04 ○
overvoltage
stall 120~150%(standard bus voltage) (220V) 120%
Current limit The actual increasing ratio is less than the ratio
P11.05 action of output frequency because of the big load 01 ◎
selection during ACC running. It is necessary to take
measures to avoid overcurrent fault and the G:
Automatic inverter trips. 160.0%
P11.06 ◎
current limit During the running of the inverter, this function P:
will detect the output current and compare it with 120.0%
85
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
the limit defined in P11.06. If it exceeds the level,
the inverter will run at stable frequency in ACC
running, or the inverter will derate to run during
the constant running. If it exceeds the level
continuously, the output frequency will keep on
decreasing to the lower limit. If the output current
is detected to be lower than the limit level, the
inverter will accelerate to run.

The
decreasing 10.00
P11.07 ◎
ratio during Hz/s
current limit

Setting range of P11.05:

0x00~0x11
LED ones:current limit
0:Invalid
1:Always invalid
LED tens:overload alarm
0:Valid
1: Invalid
Setting range of P11.06: 50.0~200.0%
Setting range of P11.07: 0.00~50.00Hz/s
Overload The output current of the inverter or the motor is
pre-alarm of above P11.09 and the lasting time is beyond
P11.08 the P11.10, overload pre-alarm will be output. 0x000 ○
motor/inverte
r
G:
Overload
150%
P11.09 pre-alarm ○
P:
test level
120%

Overload Setting range of P11.08:

pre-alarm Enable and define the overload pre-alarm of the
P11.10 1.0s ○
detection inverter or the motor.
time Setting range: 0x000~0x131
LED ones:
0:Overload pre-alarm of the motor, comply with

86
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
the rated current of the motor
1:Overload pre-alarm of the inverter, comply with
the rated current of the inverter
LED tens:
0:The inverter continues to work after underload
pre-alarm
1:The inverter continues to work after underload
pre-alarm and the inverter stops running after
overload fault
2: The inverter continues to work after overload
pre-alarm and the inverter stops running after
underload fault
3. The inverter stops when overloading or
underloading.
LED hundreds :
0:Detection all the time
1:Detection in constant running
Setting range of P11.09: P11.11~200%
Setting range of P11.10: 0.1~3600.0s
Detection
level of the If the inverter current or the output current is
P11.11 50% ○
underload lower than P11.11, and its lasting time is beyond
pre-alarm P11.12, the inverter will output underload
Detection pre-alarm.
time of the Setting range of P11.11: 0~P11.09
P11.12 1.0s ○
underload Setting range of P11.12: 0.1~3600.0s
pre-alarm
Select the action of fault output terminals on
undervoltage and fault reset.
0x00~0x11
Output
LED ones:
terminal
P11.13 0:Action under fault undervoltage 0x00 ○
action during
1:No action under fault undervoltage
fault LED tens:
0:Action during the automatic reset
1:No action during the automatic reset
0x00~0x11
LED ones:Voltage drop frequency-decreasing
Extension
selection
P11.16 functions 00 ○
0: Voltage drop frequency-decreasing selection
selection disable
1: Voltage drop frequency-decreasing selection

87
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
enable
LED tens: Step 2 ACC/DEC time option
0: Step 2 ACC/DEC time option disable
1: Step 2 ACC/DEC time option enable，when
running frequency more than P08.36, ACC/DEC
time switch to step 2 ACC/DEC time
P13 Group Reserved
Braking When P01.00=0 during the starting of the
P13.13 current of inverter, set P13.14 to a non-zero value to enter 0.0%
short-circuit the short circuit braking. ○
When the running frequency is lower than P01.09
Braking
during the stopping of the inverter, set 13.15 to a
retention time non-zero value to enter into stopping short
P13.14 0.00s
before circuited braking and then carry out the DC
○
starting braking at the time set by P01.12 (refer to the
instruction of P01.09~P01.12) .
The braking Setting range of P13.13: 0.0~150.0%
retention time (the inverter)
P13.15 0.00s
when Setting range of P13.14: 0.00~50.00s
stopping ○
Setting range of P13.15: 0.00~50.00s
P14 Group Serial communication
The setting range:1~247
When the master is writing the frame, the
communication address of the slave is set to 0;
the broadcast address is the communication
Local address. All slaves on the MODBUS fieldbus can
P14.00 communicati receive the frame, but the salve doesn’t answer. 1 ○
on address The communication address of the drive is
unique in the communication net. This is the
fundamental for the point to point communication
between the upper monitor and the drive.
Note: The address of the slave cannot set to 0.
Set the digital transmission speed between the
upper monitor and the inverter.
0:1200BPS
1:2400BPS
Communicati
P14.01 2:4800BPS 4 ○
on baud ratio
3:9600BPS
4:19200BPS
5:38400BPS
6:57600BPS

88
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
7:115200BPS
Note: The baud rate between the upper monitor
and the inverter must be the same. Otherwise,
the communication is not applied. The bigger the
baud rate, the quicker the communication speed.
The data format between the upper monitor and
the inverter must be the same. Otherwise, the
communication is not applied.
0: No check (N,8,1) for RTU
1: Even check (E,8,1) for RTU
2: Odd check (O,8,1) for RTU
3:No check (N,8,2) for RTU
4: Even check (E,8,2) for RTU
5: Odd check(O,8,2) for RTU
6: No check (N,7,1) for ASCII
Digital bit
P14.02 7: Even check (E,7,1) for ASCII 1 ○
checkout
8: Odd check (O,7,1) for ASCII
9:No check (N,7,2) for ASCII
10: Even check (E,7,2) for ASCII
11: Odd check(O,7,2) for ASCII
12: No check (N,8,1) for ASCII
13: Even check (E,8,1) for ASCII
14: Odd check (O,8,1) for ASCII
15:No check (N,8,2) for ASCII
16: Even check (E,8,2) for ASCII
17: Odd check(O,8,2) for ASCII
0~200ms
It means the interval time between the interval
time when the drive receive the data and sent it
to the upper monitor. If the answer delay is
Answer shorter than the system processing time, then the
P14.03 5 ○
delay answer delay time is the system processing time,
if the answer delay is longer than the system
processing time, then after the system deal with
the data, waits until achieving the answer delay
time to send the data to the upper monitor.
0.0(invalid), 0.1~60.0s
Fault time of When the function code is set as 0.0, the
P14.04 communicati communication overtime parameter is invalid. 0.0s ○
on overtime When the function code is set as non-zero, if the
interval time between two communications
89
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
exceeds the communication overtime, the
system will report “485 communication faults”
(CE).
Generally, set it as invalid; set the parameter in
the continuous communication to monitor the
communication state.
0:Alarm and stop freely
1:No alarm and continue to run
Transmission
2:No alarm and stop according to the stop means
P14.05 fault 0 ○
(only under the communication control)
processing
3:No alarm and stop according to the stop means
(under all control modes)
LED ones:
0: Operation with response: the drive will respond
to all reading and writing commands of the upper
monitor.
1:Operation without response；The drive only
Communicati
responds to the reading command other than the
P14.06 on 0x00 ○
writing command of the drive. The
processing
communication efficiency can be increased by
this method.
LED tens:
0: Communication encrypting valid
1: Communication encrypting invalid
P16 Group Ethernet function
P17 Group Monitoring function
Setting Display current set frequency of the inverter
P17.00 ●
frequency Range: 0.00Hz~P00.03
Output Display current output frequency of the inverter
P17.01 ●
frequency Range: 0.00Hz~P00.03
Ramp Display current ramp reference frequency of the
P17.02 reference inverter ●
frequency Range: 0.00Hz~P00.03
Output Display current output voltage of the inverter
P17.03 ●
voltage Range: 0~1200V
Output Display current output current of the inverter
P17.04 ●
current Range: 0.0~3000.0A
Display the rotation speed of the motor.
P17.05 Motor speed ●
Range: 0~65535RPM
P17.08 Motor power Display current motor power ●
90
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
Range:-300~300%
Output Display the current output torque of the inverter.
P17.09 ●
torque Range: -250.0~250.0%
Evaluated
Evaluated frequency of motor rotor
P17.10 motor ●
Range: 0.00Hz~ P00.03
frequency
DC bus Display current DC bus voltage of the inverter
P17.11 ●
voltage Range: 0.0~2000.0V
Display current Switch input terminals state of the
inverter
ON-OFF
BIT8 BIT7 BIT6 BIT5
input
P17.12 HDI S8 S7 S6 ●
terminals
BIT4 BIT3 BIT2 BIT1 BIT0
state
S5 S4 S3 S2 S1
Range: 0000~00FF
Display current Switch output terminals state of
ON-OFF
the inverter
output
P17.13 BIT3 BIT2 BIT1 BIT0 ●
terminals
RO2 RO1 HDO Y
state
Range: 0000~000F
Display the adjustment through the keypad of the
Digital
P17.14 inverter. ●
adjustment
Range : 0.00Hz~P00.03
Display the torque given, the percentage to the
torque current rated torque of the motor.
P17.15 ●
reference Setting range: -300.0%~300.0%
(the rated current of the motor)
Display the current linear speed of the inverter.
P17.16 Linear speed ●
Range: 0~65535
Display the current length of the inverter.
P17.17 Length ●
Range: 0~65535
Display the current counting number of the
Counting
P17.18 inverter. ●
value
Range: 0~65535
The inverter(≤15kW) can be set by the analog
potentiometer on the keypad and AI1 setting is
AI1 input not available for the device which is 18.5kW or
P17.19 ●
voltage higer than 18.5 kW.
Display analog AI1 input signal
Range: 0.00~10.00V
91
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
AI2 input Display analog AI2 input signal
P17.20 ●
voltage Range: 0.00~10.00V
AI3 input Display analog AI2 input signal
P17.21 ●
voltage Range: -10.00~10.00V
HDI input Display HDI input frequency
P17.22 ●
frequency Range: 0.000~50.000kHz
PID
Display PID reference value
P17.23 reference ●
Range: -100.0~100.0%
value
PID feedback Display PID response value
P17.24 ●
value Range: -100.0~100.0%
Power factor Display the current power factor of the motor.
P17.25 ●
of the motor Range: -1.00~1.00
Current Display the current running time of the inverter.
P17.26 ●
running time Range:0~65535min
Simple PLC
and the
Display simple PLC and the current step of the
current step
P17.27 multi-step speed ●
of the
Range: 0~15
multi-step
speed
AC input Display the input current in AC side.
P17.35 ●
current Range: 0.0~5000.0A
Display the output torque. Positive value is in the
Output electromotion state, and negative is in the power
P17.36 ●
torque generating state.
Range : -3000.0Nm~3000.0Nm
Counting of
P17.37 the motor 0~100 (100 is OL1 fault) ●
overload
P17.38 PID output -100.00~100.00% 0.00% ●
Wrong
P17.39 download of 0.00~99.99 0.00 ●
parameters
P24 Group Water supply
Water
0: Disabled
P24.00 supply 0 ◎
1: Enabled
selection
Press 0: AI1 setting value (The inverter(≤15kW) can be
P24.01 0 ○
feedback set by the analog potentiometer on the keypad

92
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
source and AI1 setting is not available for the device
which is 18.5kW or higer than 18.5 kW)
1: AI2 setting value
2: AI3 setting value
3: HDI setting value
Hibernation 0: Hibernate as the setting frequency﹤P24.03
P24.02 0 ◎
check 1: Hibernate as the feedback pressure﹥P24.04
Starting
frequency of 10.00
P24.03 0.00~P0.03(the Max. frequency) ○
the Hz
hibernation
Starting
P24.04 pressure of 0.00~100.0% 50.0% ○
hibernation
Hibernation
P24.05 0.0~3600.0s 5.0s ○
delay time
Hibernation 0: Awake as the setting frequency﹥P24.07
P24.06 0 ◎
awake 1: Awake as the feedback pressure﹤P24.08
Awake 20.00
P24.07 0.00~P0.03(the Max. frequency) ○
frequency Hz
Setting value
P24.08 of hibernation 0.00~100.0% 10.0% ○
awake
Mini
P24.09 hibernation 0.0~3600.0s 5.0s ○
time
Valid P24.10~P24.12 can make three motors to form a
P24.10 auxiliary simple system of water supply. 0 ○
motor
P24.11 Start/stop
delay time of
5.0s ○
auxiliary
motor 1
P24.12 Start/stop
delay time of
auxiliary
motor 2 5.0s ○

P24.10 is used to select the valid auxiliary motor.

93
Goodrive200A inverters Function parameters

Function Default
Name Detailed instruction of parameters Modify
code value
0: No auxiliary motor
1: Auxiliary motor 1 valid
2: Auxiliary motor 2 valid
3: Auxiliary motor 1 and 2 valid
Setting range of P24.10: 0.0~3600.0s
Setting range of P24.11: 0.0~3600.0s

94
Goodrive200A inverters Basic operation instruction

Basic Operation Instruction 7

7.1 What this chapter contains

This chapter describes the internal function mode of the inverter in details.
 Check all terminals are connected properly and tightly.
 Check that the power of the motor corresponds to that of the inverter.

7.2 First powering on

Check before powering on
Please check according to the installation list in chapter two.
Original powering operation
Check to ensure there is no mistake in wiring and power supply, switch on the air switch of
the AC power supply on the input side of the inverter to power on the inverter. 8.8.8.8.8. will
be displayed on the keypad, and the contactor closes normally. When the character on the
nixie tubs changes to the set frequency, the inverter has finished the initialization and it is in
the stand-by state.

Below diagram shows the first operation: (take motor 1 as the example)

95
Goodrive200A inverters Basic operation instruction

Note: If fault occurs, please do as the “Fault Tracking”. Estimate the fault reason and settle
the issue.
Besides P00.01 and P00.02, terminal command setting can also used to set the running
command channel.

96
Goodrive200A inverters Basic operation instruction

Multi-function Multi-function
Current running Multi-function
terminal 37 terminal 38
command terminal 36
Shifting the Shifting the
channel Shifting the
command to command to
P00.01 command to keypad
communication communication
Communication
Keypad running Terminal running
/ running command
command channel command channel
channel
Communication
Terminal running Keypad running
/ running command
command channel command channel
channel
Communication
Keypad running Terminal running
running command /
command channel command channel
channel
Note: “/” means the multi-function terminal is invalid on the current reference channel.
Relative parameters table:

7.3 Vector control

Because asynchronous motors have the characteristics of high stage, nonlinear, strong
coupling and various variables, the actual control of the asynchronous motor is very difficult.
Vector control is mainly used to settle this problem with the theme of that divide the stator
current vector into exciting current (the current heft generating internal magnetic field of the
motor) and torque current (the current heft generating torque) by controlling and measuring
the stator current vector according to the principles of beamed magnetic field to control the
range and phase of these two hefts. This method can realize the decoupling of exciting
current and torque current to adjust the high performance of asynchronous motors.
Goodrive200A series inverters are embedded speedless sensor vector control calculation
for driving both asynchronous motors and synchronous motors. Because the core
calculation of vector control is based on exact motor parameter models, the accuracy of
motor parameter will impact on the performance of vector control. It is recommended to input
the motor parameters and carry out autotune before vector running.
Because the vector control calculation is vary complicated, high technical theory is needed
for the user during internal autotune. It is recommended to use the specific function
parameters in vector control with cautions.

97
Goodrive200A inverters Basic operation instruction

7.4 Torque control

Goodrive200A series inverters support two kinds of control mode: torque control and rotation
speed control. The core of rotation speed is that the whole control focuses on the stable
speed and ensures the setting speed is the same as the actual running speed. The Max.
Load sould be in the range of the torque limit. The core of torque control is that the whole
control focues on the stable torque and ensures the setting torque is the same as the actual
output torque. At the same time, the output frequency is among the upper limit or the lower
limit.

98
Goodrive200A inverters Basic operation instruction

7.5 Parameters of the motor

 Physical accident may occur if the motor starts up suddenly during
autotune. Please check the safety of surrounding environment of the
motor and the load before autotune.
 The power is still applied even the motor stops running during static
autotune. Please do not touch the motor until the autotune is
completed, otherwise there would be electric shock.
 Do not carry out the rotation autotune if the motor is coupled with the
load, please do not operate on the rotation autotune. Otherwise
misaction or damage may occur to the inverter or the mechanical
devices. When carry out autotune on the motor which is coupled with
load, the motor parameter won’t be counted correctly and misaction
may occur. It is proper to de-couple the motor from the load during
autotune when necessary.

The control performance of the inverter is based on the established accurate motor model.
The user has to carry out the motor autotune before first running (take motor 1 as the
example).
Note:
1. Set the motor parameters according to the name plate of the motor.
2. During the motor autotune, de-couple the motor form the load if rotation autotune is
selected to make the motor is in a static and empty state, otherwise the result of autotune is
incorrect. The asynchronous motors can autotune the parameters of P02.06~P02.10.
3. During the motor autotune 1, do not to de-couple the motor form the load if static autotune
is selected. Because only some parameters of the motor are involved, the control
performance is not as better as the rotation autotune. The asynchronous motors can
autotune the parameters of P02.06~P02.10.
4. During the motor autotune 2, do not to de-couple the motor form the load if static autotune
is selected. Because only some parameters of the motor are involved, the control
performance is not as better as the rotation autotune. The asynchronous motors can

99
Goodrive200A inverters Basic operation instruction
autotune the parameters of P02.06~P02.08. It is suitable in the cases which SVPWM control
is applied.

7.6 Start-up and stop control

The start-up and stop control of the inverter includes three states: start after the running
command during normal powering on, start after the restarting function becomes valid during
normal powering on and start after the automatic fault reset. Below is the detailed instruction
for three starting.
There are three starting modes for the inverter: start from the starting frequency directly, start
after the DC braking and start after the rotation speed tracking. The user can select
according to different situations to meet their needs.
For the load with big inertia, especially in the cases where the reverse rotation may occur, it
is better to select starting after DC braking and then starting after rotation speed tracking.
1. The starting logic figure of starting after the running command during the normal
powering on

DE
AC

C
C

DE
AC

2. The starting logic figure of starting after the restarting function becomes valid during the
normal powering on

3. The starting logic figure of starting after the automatic fault reset

100
Goodrive200A inverters Basic operation instruction

7.7 Frequency setting

Goodrive200A series inverters can set the frequency by various means. The reference
channel can be divided into main reference channel and assistant reference channel.
There are two main reference channels: A frequency reference channel and B frequency
reference channel. These two reference channels can carry out mutual simple math
calculation between each other. And the reference channels can be shifted dynamically
through set multi- function terminals.
There are three assistant reference channels: keypad UP/DOWN input, terminals
UP/DOWN switch input and digital potentiometer input. The three ways equal to the effect of
input UP/DOWN reference in internal assistant reference of the inverter. The user can
enable the reference method and the effect of the method to the frequency reference by
setting function codes.
The actual reference of the inverter is consisted of main reference channel and assistant
reference channel.

101
Goodrive200A inverters Basic operation instruction

Goodrive200A series inverters support the shifting between different reference channels and
the detailed shifting rules is as below:
Multi-function Multi-function Multi-function terminal
Current
terminal function 13 terminal function 14 function 15
reference
Shifting from A Shifting from Shifting from
channel
channel to B combination setting combination setting to
P00.09
channel to A channel B channel
A B / /
B A / /
A+B / A B
A-B / A B
Max(A,B) / A B
Min(A,B) / A B
Note: “/” means the multi-function terminal is invalid under the current reference channel.
When select multi-function terminal UP (10) and DOWN (11) to set the internal assistant
frequency, P08.44 and P08.45 can be set to increase or decrease the set frequency quickly.
102
Goodrive200A inverters Basic operation instruction

7.8 Simple PLC

Simple PLC function is also a multi-step speed generator. The inverter can change the
running frequency, direction to meet the need of processing according to the running time
automatically. In the past, this function needs to be assisted by external PLC, but now the
inverter can realize this function by itself.
The series inverters can control 16-step speed with 4 groups of ACC/DEC time.
The multi-function digital output terminals or multi-function relay output an ON signal when
the set PLC finishes a circle (or a step).

7.9 Multi-step speed running

Set the parameters when the inverter carries out multi-step speed running. Goodrive200A
series inverters can set 16 step speed which can be selected by the combination code of
multi-step speed terminals 1~4. They correspond to multi-step speed 0 to 15.

103
Goodrive200A inverters Basic operation instruction
P10.02 multi-stage speed 0 BIT0
P10.03 the running time of stage 0 BIT1 P10.34
Terminal function 16
Multi-stage speed OFF ON OFF ON OFF ON OFF ON The ACC/DEC time selection
terminal 1
of Stage 0~7 of PLC
Terminal function 17 P10.04 multi-stage speed 1 BIT2
Multi-stage speed OFF OFF ON ON ON OFF OFF ON
P10.05 the running time of stage 1 BIT3
terminal 21

Terminal function 18
Multi-stage speed OFF OFF OFF OFF ON ON ON ON 00 P00.10 ACC time 1
terminal 3 P10.06 multi-stage speed 2 BIT4 P00.12 DEC time 1
P10.07 the running time of stage 2 BIT5
Terminal function 19
Multi-stage speed OFF OFF OFF OFF OFF OFF OFF OFF
terminal 4
01 P08.00 ACC time 2
P10.08 multi-stage speed 3 BIT6 P08.01 DEC time 2
Multi-stage 0 1 2 3 4 5 6 7
P10.09 the running time of stage 3 BIT7
speed

10 P08.02 ACC time 3

Multi-stage P10.10 multi-stage speed 4 BIT8 P08.03 DEC time 3
speed 15 P10.11 the running time of stage 4 BIT9

11 P08.04 ACC time 4

P10.12 multi-stage speed 5 BIT10 P08.15 DEC time 4
P10.13 the running time of stage 5 BIT11

Multi-stage
speed 0
Multi-stage P10.14 multi-stage speed 6 BIT12
speed 1 P10.15 the running time of stage 6 BIT13

P10.16 multi-stage speed 7 BIT14

P10.17 the running time of stage 7 BIT15 Valid Frequency
retention
ON OFF
Running command
Invalid Multi-stage speed
P10.18 multi-stage speed 8 BIT0 output
P10.19 the running time of stage 8 BIT1 The ACC/DEC time selection
Terminal function 16
Multi-stage speed 1 of Stage 8~15 of PLC

Terminal function 17 P10.20 multi-stage speed 9 BIT2

Multi-stage speed 2 P10.21 the running time of stage 9 BIT3

Terminal function 18
Multi-stage speed 00
terminal 3 P00.10 ACC time 1
P10.22 multi-stage speed 10 P00.12 DEC time 1
BIT4
P10.23 the running time of stage
Terminal function 19 BIT5
10
Multi-stage speed
terminal 1
01 P08.00 ACC time 2
P10.24 multi-stage speed 11 P08.01 DEC time 2
BIT6
P10.25 the running time of stage
BIT7
11

Terminal function 16
Multi-stage speed OFF ON OFF ON OFF ON OFF ON 10 P08.02 ACC time 3
terminal 1 P10.26 multi-stage speed 12 P08.03 DEC time 3
BIT8
P10.27 the running time of stage
12 BIT9
Terminal function 17
Multi-stage speed OFF OFF ON ON ON OFF OFF ON
terminal 2
11 P08.04 ACC time 4
Terminal function 18 P10.28 multi-stage speed 13 P08.15 DEC time 4
BIT10
Multi-stage speed OFF OFF OFF OFF ON ON ON ON P10.29 the running time of stage BIT11
terminal 3 13

Terminal function 19
Multi-stage speed ON ON ON ON ON ON ON ON
terminal 4 P10.30 multi-stage speed 14
BIT12
P10.31 the running time of stage
BIT13
14
Multi-stage 8 9 10 11 12 13 14 15
speed

P10.32 multi-stage speed 15 BIT14

P10.33 the running time of stage 15 BIT15

7.10 PID control

PID control is commonly used to control the procedure. Adjust the output frequency by
proportional, integral, differential operation with the dispersion of the target signals to
stabilize the value on the target. It is possible to apply to the flow, pressure and temperature
control. Figure of basic control is as below:

104
Goodrive200A inverters Basic operation instruction

When P00.06, P00. 07=7 or P04.27=6, the running mode of the inverter is procedure PID
control.
7.15.1 General steps of PID parameters setting:
a Ensure the gain P
When ensure the gain P, firstly cancel the PID integration and derivation (set Ti=0 and Td=0,
see the PID parameter setting for detailed information) to make proportional adjustment is
the only method to PID. Set the input as 60%~70% of the permitted Max. Value and
increase gain P from 0 until the system vibration occurs, vice versa, and record the PID
value and set it to 60%~70% of the current value. Then the gain P commission is finished.
b Ensure the integration time
After ensuring the gain P, set an original value of a bigger integration time and decrease it
until the system vibration occurs, vice versa, until the system vibration disappear. Record the
Ti and set the integration time to 150%~180% of the current value. Then integration time
commission is finished.
c Ensure the derivation time
Generally, it is not necessary to set Td which is 0.
If it needs to be set, set it to 30% of the value without vibration via the same method with P
and Ti.
d Commission the system with and without load and then adjust the PID parameter until it is
available.
7.15.2 PID inching
After setting the PID control parameters, inching is possible by following means:
Control the overshoot
Shorten the derivation time and prolong the integration time when overshoot occurs.

105
Goodrive200A inverters Basic operation instruction

Achieve the stable state as soon as possible

Shorten the integration time (Ti) and prolong the derivation time (Td) even the overshoot
occurs, but the control should be stable as soon as possible.

Control long vibration

If the vibration periods are longer than the set value of integration time (Ti), it is necessary to
prolong the integration time (Ti) to control the vibration for the strong integration.

Control short vibration

Short vibration period and the same set value with the derivation time (Td) mean that the
derivation time is strong. Shortening the derivation time (Td) can control the vibration. When
setting the derivation time as 0.00(ire no derivation control) is useless to control the vibration,
decrease the gain.

7.11 Pulse counter

Goodrive200A series inverters support pulse counter which can input counting pulse through
HDI terminal. When the actual length is longer than or equal to the set length, the digital
106
Goodrive200A inverters Basic operation instruction
output terminal can output length arrival pulse signal and the corresponding length will be
cleared automatically.

107
Goodrive200A inverters Fault tracking

Fault Tracking 8

8.1 What this chapter contains

This chapter describes how to reset faults and view fault history. It also lists all alarm and
fault messages including the possible cause and corrective actions.
 Only qualified electricians are allowed to maintain the inverter. Read the
safety instructions in chapter Safety precautions before working on the
inverter.

8.2 Alarm and fault indications

Fault is indicated by LEDs. See Operation Procedure. When TRIP light is on, an alarm or
fault message on the panel display indicates abnormal inverter state. Using the information
reference in this chapter, most alarm and fault cause can be identified and corrected. If not,
contact with the INVT office.

8.3 How to reset

The inverter can be reset by pressing the keypad key STOP/RST, through digital input, or by
switching the power light. When the fault has been removed, the motor can be restarted.

8.4 Fault history

Function codes P07.27~P07.32 store 6 recent faults. Function codes P07.33~P07.40,
P07.41~P7.48 and P07.49~P07.56 show drive operation data when the latest 3 faults
occurs.

8.5 Fault instruction and solution

Do as the following after the inverter fault:
1. Check to ensure there is nothing wrong with the keypad. If not, please contact with the
local INVT office.
2. If there is nothing wrong, please check P07 and ensure the corresponding recorded fault
parameters to confirm the real state when the current fault occurs by all parameters.
3. See the following table for detailed solution and check the corresponding abnormal state.
4. Eliminate the fault and ask for relative help.
5. Check to eliminate the fault and carry out fault reset to run the inverter.
Fault code Fault type Possible cause What to do
The acceleration is too
OUt1 IGBT Ph-U fault
fast Increase Acc time
OUt2 IGBT Ph-V fault IGBT module fault Change the power unit
Misaction caused by Check the driving wires
interference Inspect external
The connection of the equipment and eliminate
OUt3 IGBT Ph-W fault
driving wires is not good, interference
Grounding is not properly

108
Goodrive200A inverters Fault tracking
Fault code Fault type Possible cause What to do
Over-current when The acceleration or Increase the ACC time
OC1
acceleration deceleration is too fast Check the input power
Over-current when The voltage of the grid is Select the inverter with a
OC2
deceleration too low larger power
The power of the inverter Check if the load is short
is too low circuited (the grounding
The load transients or is short circuited or the wire
abnormal short circuited) or the
Over-current when The grounding is short rotation is not smooth
OC3 constant speed circuited or the output is Check the output
running phase loss configuration.
There is strong external Check if there is strong
interference interference
The overvoltage stall Check the setting of
protection is not open relative function codes
Over-voltage Check the input power
OV1
when acceleration Check if the DEC time of
Over-voltage the load is too short or the
OV2 The input voltage is
when deceleration inverter starts during the
abnormal
rotation of the motor or it
There is large energy
needs to add the dynamic
feedback
Over-voltage bracking components
No braking components
OV3 when constant Install the braking
Braking energy is not open
speed running components
Check the setting of
relative function codes
The voltage of the power Check the input power of
DC bus supply is too low the supply line
UV
Under-voltage The overvoltage stall Check the setting of
protection is not open relative function codes
The voltage of the power Check the power of the
supply is too low supply line
The motor setting rated Reset the rated current of
OL1 Motor overload
current is incorrect the motor
The motor stall or load Check the load and adjust
transients is too strong the torque lift
The acceleration is too Increase the ACC time
fast Avoid the restarting after
Reset the rotating motor stopping
The voltage of the power Check the power of the
OL2 Inverter overload
supply is too low supply line
The load is too heavy Select an inverter with
The motor power is too bigger power
small Select a proper motor

109
Goodrive200A inverters Fault tracking
Fault code Fault type Possible cause What to do
The inverter will report
Check the load and the
OL3 Electrical overload overload pre-alarm
overload pre-alarm point.
according to the set value
Check input power
Phase loss or fluctuation
SPI Input phase loss Check installation
of input R,S,T
distribution
Check the output
U,V,W phase loss input(or
distribution
SPO Output phase loss serious asymmetrical
Check the motor and
three phase of the load)
cable

Air duct jam or fan

damage Clean the air duct or the
OH1 Rectify overheat Ambient temperature is fan
too high Reduce the ambient
The time of overload temperature
running is too long
OH2 IGBT overheat
SI external fault input Check the external device
EF External fault
terminals action input
The baud rate setting is Set proper baud rate
incorrect Check the communication
Fault occurs to the connection distribution
communication wiring. Set proper communication
Communication
CE The communication address
error
address is wrong Chang or replace the
There is strong connection distribution or
interference to the improve the
communication anti-interference capability
The connection of the
Check the connector and
control board is not good
repatch
Current detection Hoare components is
ItE Change the hoare
fault broken
Change the main control
The modifying circuit is
panel
abnormal
Change the inverter mode
The motor capacity does
Set the rated parameter
not comply with the
according to the motor
inverter capability
name plate
The rated parameter of the
Empty the motor load and
motor does not set
reindentify
tE Autotuning fault correctly.
Check the motor
The offset between the
connection and set the
parameters autotunting
parameter.
and the standard
Check if the upper limit
parameter is huge
frequency is above 2/3 of
Autotune overtime
the rated frequency.

110
Goodrive200A inverters Fault tracking
Fault code Fault type Possible cause What to do
Error of controlling the
Press STOP/RST to reset
write and read of the
EEP EEPROM fault Change the main control
parameters
panel
Damage to EEPROM
Check the PID feedback
PID feedback offline
signal
PIDE PID feedback fault PID feedback source
Check the PID feedback
disappear
source
Braking circuit fault or
Check the braking unit and
damage to the braking
change new braking pipe
bCE Braking unit fault pipes
Increase the braking
The external braking
resistor
resistor is not sufficient
Grounding The output of the inverter
ETH1 Check if the connection of
shortcut fault 1 is short circuited with the
the motor is normal or not
ground
Change the hoare
There is fault in the current
Change the main control
Grounding detection circuit
ETH2 panel
shortcut fault 2 The actual motor power
Set motor parameters
sharply differs from the
correctly.
inverter power.
Check the load and
ensure it is normal
Velocity deviation The load is too heavy or Increase the detection
dEu
fault stalled time
Check whether the control
parameters are normal
Check the load and
The control parameters of
ensure it is normal
the synchronous motors
Check whether the control
not set properly
Maladjustment parameter is set properly
STo The autoturn parameter is
fault or not
not right
Increase the
The inverter is not
maladjustment detection
connected to the motor
time
The actual running time of
Ask for the supplier and
Time reach of the inverter is above the
END adjust the setting running
factory setting internal setting running
time
time

111
Goodrive200A inverters Fault tracking
Fault code Fault type Possible cause What to do
The connection of the
Check the keypad wires
keypad wires is not good
and ensure whether there
or broken
is mistake
Keypad The keypad wire is too
Check the environment
PCE communication long and affected by
and avoid the interference
fault strong interference
source
There is circuit fault on the
Change the hardware and
communication of the
ask for service
keypad and main board
The connection of the
Check the keypad wires
keypad wires is not good
and ensure whether there
or broken
is mistake
Parameters The keypad wire is too
DNE Change the hardware and
downloading fault long and affected by
ask for service
strong interference
Repack-up the data in the
 There is mistake on the
keypad
data storage of the keypad
The inverter will report the
Electronic Check the load and the
LL underload pre-alarm
underload fault underload pre-alarm point
according to the set value

8.5.2 Other states

Fault code Fault type Possible cause What to do
System power System power off or the
PoFF Check the grid
off bus voltage is too low
Communication
failure between
The keypad is not conneted Check the installation
the keypad and
correctly environment
main control
board

112
Goodrive200A inverters Fault tracking

8.6 Common fault analysis

8.6.1 The motor does not work

8.6.2 Motor vibration

113
Goodrive200A inverters Fault tracking

8.6.3 Overvoltage

8.6.4 Undervoltage fault

114
Goodrive200A inverters Fault tracking

8.6.5 Abnormal motor heat

115
Goodrive200A inverters Fault tracking

8.6.6 Inverter overheating

8.6.7 Stall during the acceleration of the motor

116
Goodrive200A inverters Fault tracking

8.6.8 Overcurrent

8.7 Inverter system interference troubleshooting

If sensitive devices(PLC,PC,sensors,test enquipment,etc.) exist interference problems when
the system is running, you can troubleshoot by the following means:
1. Try plugging in or unplugging the jumper pins of C3 filter to verify whether the interference
has been eliminated.
2. Check whether the drive power lines and the signal/ communication lines of sensitive
equipment go down the same trough, if there is, it should be again separated from the
wiring.
3. If the sensitive equipment and drive to take power from the same grid, it is
recommended to install isolation transformer and filter to the distribution of sensitive
equipment side.
4. The relative shield wire of sensitive equipment try to ground at both ends 、
single-grounded、ungrounded respectively; to verify whether the interference has been
eliminated.
5. Try to make the interfered sensitive equipment and the drive have no common ground, or

117
Goodrive200A inverters Fault tracking
floating processing; to verify whether the interference has been eliminated.

8.8 Maintenance and hardware diagnostics

8.8.1 Overcurrent
If installed in an appropriate environment, the inverter requires very little maintenance. The
table lists the routine maintenance intervals recommended by INVT.
Checking
Checking part Checking item Criterion
method
Check the ambient
Visual
temperature, humidity
examination Conforming to
and vibration and ensure
and instrument the manual
there is no dust, gas, oil
test
Ambient environment fog and water drop.
There are no
Ensure there are no tools
Visual tools or
or other foreign or
examination dangerous
dangerous objects
objects.
Ensure the main circuit
Measurement by Conforming to
Voltage and control circuit are
millimeter the manual
normal.
The characters
Ensure the display is Visual
are displayed
clear enough examination
Keypad normally.
Ensure the characters Visual Conforming to
are displayed totally examination the manual
Ensure the screws are
Tighten up NA
tightened up
Ensure there is no
distortion, crackles,
damage or
Visual
color-changing caused by NA
examination
overheating and aging to
the machine and
insulator.
For public use
NA
Main
Note: if the color
circuit
of the copper
blocks change, it
Ensure there is no dust Visual
does not mean
and dirtiness examination
that there is
something
wrong with the
features.
Ensure that there is no
The lead of the Visual
distortion or NA
conductors examination
color-changing of the

118
Goodrive200A inverters Fault tracking
Checking
Checking part Checking item Criterion
method
conductors caused by
overheating.
Ensure that there are no
crackles or Visual
NA
color-changing of the examination
protective layers.
Ensure that there is no Visual
Terminals seat NA
damage examination
Ensure that there is no
weeping, color-changing, Visual
NA
crackles and cassis examination
expansion.
Estimate the
usage time
Ensure the safety valve is according to the
NA
Filter capacitors in the right place. maintenance or
measure the
static capacity.
The static
Measure the capacity is
If necessary, measure the
capacity by above or equal
static capacity.
instruments. to the original
value *0.85.
Ensure whether there is Smelling and
replacement and splitting visual NA
caused by overheating. examination
Visual
examination or
Resistors
remove one The resistors are
Ensure that there is no
ending to in ±10% of the
offline.
coagulate or standard value.
measure with
multimeters
Hearing,
Ensure there is no
Transformers and smelling and
abnormal vibration, noise NA
reactors visual
and smelling,
examination
Ensure whether there is
Electromagnetism vibration noise in the Hearing NA
contactors and workrooms.
relays Ensure the contactor is Visual
NA
good enough. examination
Ensure there are no
Control
PCB and plugs loose screws and Fasten up NA
circuit
contactors.
119
Goodrive200A inverters Fault tracking
Checking
Checking part Checking item Criterion
method
Ensure there is no Smelling and
smelling and visual NA
color-changing. examination
Ensure there are no
Visual
crackles, damage NA
examination
distortion and rust.
Visual
examination or
Ensure there is no estimate the
weeping and distortion to usage time NA
the capacitors. according to the
maintenance
information
Hearing and
Estimate whether there is
Visual
abnormal noise and Stable rotation
examination or
vibration.
rotate with hand
Estimate there is no
Tighten up NA
losses screw.
Cooling fan Visual
examination or
Cooling
Ensure there is no estimate the
system
color-changing caused by usage time NA
overheating. according to the
maintenance
information
Ensure whether there is
stuff or foreign objection Visual
Ventilating duct NA
in the cooling fan, air examination
vent.
Consult the local service representative for more details on the maintenance. Visit the official
website of INVT: http://www.invt.com.cn and select Inverter Services – Maintenance and
Services.

8.8.2 Cooling fan

The inverter’s cooling fan has a minimum life span of 25,000 operating hours. The actual life
span depends on the inverter usage and ambient temperature.
The operating hours can be found through P07.14 (accumulative hours of the inverter).
Fan failure can be predicted by the increasing noise from the fan bearings. If the inverter is
operated in a critical part of a process, fan replacement is recommended once these
symptoms appear. Replacement fans are available from INVT.

120
Goodrive200A inverters Fault tracking

8.8.2.1Replacing the cooling fan

 Read and follow the instructions in chapter Safety Precautions.
Ignoring the instructions would cause physical injury or death, or
damage to the equipment.
1. Stop the inverter and disconnect it from the AC power source and wait for at least the time
designated on the inverter.
2. Lever the fan holder off the drive frame with a screwdriver and lift the hinged fan holder
slightly upward from its front edge.
3. Loose the fan cable from the clip.
4. Disconnect the fan cable.
5. Remove the fan holder from the hinges.
6. Install the new fan holder including the fan in reverse order. Keep the wind direction of the

fan consistent with that of the inverter, as shown below:

Wind Rotation Wind

direction direction direction

Wind
direction
Rotation Wind
direction direction

Fan maintenance diagram for inverters

7. Restore power.
8.8.3 Capacitors

8.8.3.1 Reforming the capacitors

The DC bus capacitors must be reformed according to the operation instruction if the
inverter has been stored for a long time. The storing time is counted form the producing date
other than the delivery data which has been marked in the serial number of the inverter.
Time Operational principle
Storing time less than 1
Operation without charging
year
Storing time 1-2 years Connect with the power for 1 hour before first ON command
Use power surge to charge for the inverter
• Add 25% rated voltage for 30 minutes
Storing time 2-3 years • Add 50% rated voltage for 30 minutes
• Add 75% rated voltage for 30 minutes
• Add 100% rated voltage for 30 minutes
Use power surge to charge for the inverter
• Add 25% rated voltage for 2 hours
Storing time more than 3
• Add 50% rated voltage for 2 hours
years
• Add 75% rated voltage for 2 hours
• Add 100% rated voltage for 2 hours
The method of using power surge to charge for the inverter:
121
Goodrive200A inverters Fault tracking
The right selection of Power surge depends on the supply power of the inverter. Single
phase 220V AC/2A power surge applied to the inverter with single/three-phase 220V AC as
its input voltage. The inverter with single/three-phase 220V AC as its input voltage can apply
Single phase 220V AC/2A power surge. All DC bus capacitors charge at the same time
because there is one rectifier.
High-voltage inverter needs enough voltage (for example, 380V) during charging. The small
capacitor power (2A is enough) can be used because the capacitor nearly does not need
current when charging.
The operation method of inverter charging through resistors (LEDs):
The charging time is at least 60 minutes if charge the DC bus capacitor directly through
supply power. This operation is available on normal temperature and no-load condition and
the resistor should be serially connected in the 3-phase circuits of the power supply(the
distance between resistors of each phase≥5.5mm):
380V drive device: 1k/100W resistor. LED of 100W can be used when the power voltage is
no more than 380V. But if used, the light may be off or weak during charging.

380V charging illustration of the driven device

8.8.3.2 Change electrolytic capacitors

 Read and follow the instructions in chapter Safety Precautions.
Ignoring the instructions may cause physical injury or death, or
damage to the equipment.
Change electrolytic capacitors if the working hours of electrolytic capacitors in the inverter
are above 35000. Please contact with the local INVT offices or dial our national service
hotline (400-700-9997) for detailed operation.

8.8.4 Power cable

 Read and follow the instructions in chapter Safety Precautions.
Ignoring the instructions may cause physical injury or death, or
damage to the equipment.
1. Stop the drive and disconnect it from the power line. Wait for at least the time designated
on the inverter.
2. Check the tightness of the power cable connections.
3. Restore power.

122
Goodrive200A inverters Communication protocol

Communication Protocol 9

9.1 What this chapter contains

This chapter describes the communication protocol of Goodrive200A series inverters.
The Goodrive200A series inverters provide RS485 communication interface. It adopts
international standard MODBUS communication protocol to perform master-slave
communication. The user can realize centralized control through PC/PLC, upper control PC,
etc. (set the control command, running frequency of the inverter, modify relevant function
codes, monitor and control the operating state and fault information of the inverter and so on)
to adapt specific application requirements.

9.2 Brief instruction to MODBUS protocol

MODBUS protocol is a software protocol and common language which is applied in the
electrical controller. With this protocol, the controller can communicate with other devices via
network (the channel of signal transmission or the physical layer, such as RS485). And with
this industrial standard, the controlling devices of different manufacturers can be connected
to an industrial network for the convenient of being monitored.
There are two transmission modes for MODBUS protocol: ASCII mode and RTU (Remote
Terminal Units) mode. On one MODBUS network, all devices should select same
transmission mode and their basic parameters, such as baud rate, digital bit, check bit, and
stopping bit should have no difference.
MODBUS network is a controlling network with single-master and multiple slaves, which
means that there is only one device performs as the master and the others are the slaves on
one MODBUS network. The master means the device which has active talking right to sent
message to MODBUS network for the controlling and inquiring to other devices. The slave
means the passive device which sends data message to the MODBUS network only after
receiving the controlling or inquiring message (command) form the master (response). After
the master sends message, there is a period of time left for the controlled or inquired slaves
to response, which ensure there is only one slave sends message to the master at a time for
the avoidance of singles impact.
Generally, the user can set PC, PLC, IPC and HMI as the masters to realize central control.
Setting certain device as the master is a promise other than setting by a bottom or a switch
or the device has a special message format. For example, when the upper monitor is
running, if the operator clicks sending command bottom, the upper monitor can send
command message actively even it can not receive the message form other devices. In this
case, the upper monitor is the master. And if the designer makes the inverter send the data
only after receiving the command, then the inverter is the slave.
The master can communicate with any single slave or with all slaves. For the single-visiting
command, the slave should feedback a response message; for the broadcasting message
from the master, the slave does not need to feedback the response message.

123
Goodrive200A inverters Communication protocol

9.3 Application of the inverter

The MODBUS protocol of the inverter is RTU mode and the physical layer is 2-wire RS485.

9.3.1 RS485
The interface of 2-wire RS485 works on semiduplex and its data signal applies differential
transmission which is called balance transmission, too. It uses twisted pairs, one of which is
defined as A (+) and the other is defined as B (-). Generally, if the positive electrical level
between sending drive A and B is among +2~+6V, it is logic“1”, if the electrical level is among
-2V~-6V; it is logic“0”.
485+ on the terminal board corresponds to A and 485- to B.
Communication baud rate means the binary bit number in one second. The unit is bit/s (bps).
The higher the baud rate is, the quicker the transmission speed is and the weaker the
anti-interference is. If the twisted pairs of 0.56mm（24AWG）is applied as the communication
cables, the Max. Transmission distance is as below:
Max. transmission Max. transmission
Baud rate Baud rate
distance distance
2400BPS 1800m 9600BPS 800m
4800BPS 1200m 19200BPS 600m
It is recommended to use shield cables and make the shield layer as the grounding wires
during RS485 remote communication.
In the cases with less devices and shorter distance, it is recommended to use 120Ω terminal
resistor as the performance will be weakened if the distance increase even though the
network can perform well without load resistor.
9.3.2 RTU mode

9.3.2.1 RTU communication frame format

If the controller is set to communicate by RTU mode in MODBUS network every 8bit byte in
the message includes two 4Bit hex characters. Compared with ACSII mode, this mode can
send more data at the same baud rate.
Code system
· 1 start bit
· 7 or 8 digital bit, the minimum valid bit can be sent firstly. Every 8 bit frame includes two
hex characters (0...9, A...F)
· 1 even/odd check bit . If there is no checkout, the even/odd check bit is inexistent.
· 1 end bit (with checkout), 2 Bit(no checkout)
Error detection field
· CRC
The data format is illustrated as below:
11-bit character frame (BIT1~BIT8 are the digital bits)
Check
Start bit BIT1 BIT2 BIT3 BIT4 BIT5 BIT6 BIT7 BIT8 End bit
bit
10-bit character frame (BIT1~BIT7 are the digital bits)
Check
Start bit BIT1 BIT2 BIT3 BIT4 BIT5 BIT6 BIT7 End bit
bit
124
Goodrive200A inverters Communication protocol
In one character frame, the digital bit takes effect. The start bit, check bit and end bit is used
to send the digital bit right to the other device. The digital bit, even/odd checkout and end bit
should be set as the same in real application.
The MODBUS minimum idle time between frames should be no less than 3.5 bytes. The
network device is detecting, even during the interval time, the network bus. When the first
field (the address field) is received, the corresponding device decodes next transmitting
character. When the interval time is at least 3.5 byte, the message ends.
The whole message frame in RTU mode is a continuous transmitting flow. If there is an
interval time (more than 1.5 bytes) before the completion of the frame, the receiving device
will renew the uncompleted message and suppose the next byte as the address field of the
new message. As such, if the new message follows the previous one within the interval time
of 3.5 bytes, the receiving device will deal with it as the same with the previous message. If
these two phenomena all happen during the transmission, the CRC will generate a fault
message to respond to the sending devices.
The standard structure of RTU frame:
START T1-T2-T3-T4(transmission time of 3.5 bytes)
Communication address: 0~247(decimal system)(0 is the broadcast
ADDR
address)
03H:read slave parameters
CMD
06H:write slave parameters
DATA (N-1)
The data of 2*N bytes are the main content of the communication as
…
well as the core of data exchanging
DATA (0)
CRC CHK low bit
Detection value:CRC (16BIT）
CRC CHK high bit
END T1-T2-T3-T4(transmission time of 3.5 bytes)

9.3.2.2 RTU communication frame error checkout

Various factors (such as electromagnetic interference) may cause error in the data
transmission. For example, if the sending message is a logic “1”,A-B potential difference on
RS485 should be 6V, but in reality, it may be -6V because of electromagnetic interference,
and then the other devices take the sent message as logic“0”. If there is no error checkout,
the receiving devices will not find the message is wrong and they may give incorrect
response which cause serious result. So the checkout is essential to the message.
The theme of checkout is that: the sender calculate the sending data according to a fixed
formula, and then send the result with the message. When the receiver gets this message,
they will calculate anther result according to the same method and compare it with the
sending one. If two results are the same, the message is correct. If not, the message is
incorrect.
The error checkout of the frame can be divided into two parts: the bit checkout of the byte
and the whole data checkout of the frame (CRC check).
Bit checkout of the byte
The user can select different bit checkouts or non-checkout, which impacts the check bit

125
Goodrive200A inverters Communication protocol
setting of each byte.
The definition of even checkout: add an even check bit before the data transmission to
illustrate the number of “1” in the data transmission is odd number or even number. When it is
even, the check byte is “0”, otherwise, the check byte is”1”. This method is used to stabilize
the parity of the data.
The definition of odd checkout: add an odd check bit before the data transmission to illustrate
the number of “1” in the data transmission is odd number or even number. When it is odd, the
check byte is “0”, otherwise, the check byte is”1”. This method is used to stabilize the parity
of the data.
For example, when transmitting “11001110”, there are five “1” in the data. If the even
checkout is applied, the even check bit is “1”; if the odd checkout is applied; the odd check bit
is “0”. The even and odd check bit is calculated on the check bit position of the frame. And
the receiving devices also carry out even and odd checkout. If the parity of the receiving data
is different from the setting value, there is an error in the communication.
CRC check
The checkout uses RTU frame format. The frame includes the frame error detection field
which is based on the CRC calculation method. The CRC field is two bytes, including 16
figure binary values. It is added into the frame after calculated by transmitting device. The
receiving device recalculates the CRC of the received frame and compares them with the
value in the received CRC field. If the two CRC values are different, there is an error in the
communication.
During CRC, 0*FFFF will be stored. And then, deal with the continuous 6-above bytes in the
frame and the value in the register. Only the 8Bit data in every character is effective to CRC,
while the start bit, the end and the odd and even check bit is ineffective.
The calculation of CRC applies the international standard CRC checkout principles. When
the user is editing CRC calculation, he can refer to the relative standard CRC calculation to
write the required CRC calculation program.
Here provided a simple function of CRC calculation for the reference (programmed with C
language):
unsigned int crc_cal_value(unsigned char *data_value,unsigned char data_length)
{
int i;
unsigned int crc_value=0xffff;
while(data_length--)
{ crc_value^=*data_value++;
for(i=0;i<8;i++)
{
if(crc_value&0x0001)crc_value=(crc_value>>1)^0xa001;
else crc_value=crc_value>>1;
} }
return(crc_value);
}
In ladder logic, CKSM calculated the CRC value according to the frame with the table inquiry.

126
Goodrive200A inverters Communication protocol
The method is advanced with easy program and quick calculation speed. But the ROM
space the program occupied is huge. So use it with caution according to the program
required space.

9.4 RTU command code and communication data illustration

9.4.1 RTU mode

9.4.1.1Command code: 03H

read N words（Word）(the Max. continuous reading is 16 words)
Command code 03H means that if the master read data form the inverter, the reading
number depends on the “data number” in the command code. Max. continuous reading
number is 16 and the parameter address should be continuous. The byte length of every
data is 2 (one word). The following command format is illustrated by hex (a number with “H”
means hex) and one hex occupies one byte.
The command code is used to read the working step of the inverter.
For example, read continuous 2 data content from0004H from the inverter with the address
of 01H (read the content of data address of 0004H and 0005H), the frame structure is as
below:
RTU master command message (from the master to the inverter)
START T1-T2-T3-T4 (transmission time of 3.5 bytes)
ADDR 01H
CMD 03H
High bit of the start address 00H
Low bit of the start address 04H
High bit of data number 00H
Low bit of data number 02H
CRC low bit 85H
CRC high bit CAH
END T1-T2-T3-T4 (transmission time of 3.5 bytes)
T1-T2-T3-T4 between START and END is to provide at least the time of 3.5 bytes as the
leisure time and distinguish two messages for the avoidance of taking two messages as one
message.
ADDR = 01H means the command message is sent to the inverter with the address of 01H
and ADDR occupies one byte
CMD=03H means the command message is sent to read data form the inverter and CMD
occupies one byte
“Start address” means reading data form the address and it occupies 2 bytes with the fact
that the high bit is in the front and the low bit is in the behind.
“Data number” means the reading data number with the unit of word. If the “start address’ is
0004H and the “data number” is 0002H, the data of 0004H and 0005H will be read.
CRC occupies 2 bytes with the fact that the high bit is in the front and the low bit is in the
behind.
RTU slave response message (from the inverter to the master)
127
Goodrive200A inverters Communication protocol

START T1-T2-T3-T4 (transmission time of 3.5 bytes)

ADDR 01H
CMD 03H
Byte number 04H
Data high bit of address 0004H 13H
Data low bit of address 0004H 88H
Data high bit of address 0005H 00H
Data low bit of address 0005H 00H
CRC CHK low bit 7EH
CRC CHK high bit 9DH
END T1-T2-T3-T4 (transmission time of 3.5 bytes)
The meaning of the response is that:
ADDR = 01H means the command message is sent to the inverter with the address of 01H
and ADDR occupies one byte
CMD=03H means the message is received from the inverter to the master for the response
of reading command and CMD occupies one byte
“Byte number” means all byte number from the byte(excluding the byte) to CRC
byte(excluding the byte). 04 means there are 4 byte of data from the “byte number” to “CRC
CHK low bit”, which are “digital address 0004H high bit”, “digital address 0004H low bit”,
“digital address 0005H high bit” and “digital address 0005H low bit”.
There are 2 bytes stored in one data with the fact that the high bit is in the front and the low
bit is in the behind of the message, the data of data address 0004H is 1388H, and the data
of data address 0005H is 0000H.
CRC occupies 2 bytes with the fact that the high bit is in the front and the low bit is in the
behind.

9.4.1.2 Command code: 06H

06H (correspond to binary 0000 0110), write one word(Word)
The command means that the master write data to the inverter and one command can write
one data other than multiple dates. The effect is to change the working mode of the inverter.
For example, write 5000 (1388H) to 0004H from the inverter with the address of 02H, the
frame structure is as below:
RTU master command message (from the master to the inverter)
START T1-T2-T3-T4(transmission time of 3.5 bytes)
ADDR 02H
CMD 06H
High bit of write data address 00H
Low bit of write data address 04H
High bit of data content 13H
Low bit of data content 88H
CRC CHK low bit C5H
CRC CHK high bit 6EH
END T1-T2-T3-T4 (transmission time of 3.5 bytes)
128
Goodrive200A inverters Communication protocol
RTU slave response message (from the inverter to the master)
START T1-T2-T3-T4 (transmission time of 3.5 bytes)
ADDR 02H
CMD 06H
High bit of writing data address 00H
Low bit of writing data address 04H
High bit of data content 13H
Low bit of data content 88H
CRC CHK low bit C5H
CRC CHK high bit 6EH
END T1-T2-T3-T4 (transmission time of 3.5 bytes)
Note: section 10.2 and 10.3 mainly describe the command format, and the detailed
application will be mentioned in 10.8 with examples.

9.4.1.3 Command code 08H for diagnosis

Meaning of sub-function codes
Sub-function Code Description
0000 Return to inquire information data
For example: The inquiry information string is same as the response information string when
the loop detection to address 01H of driver is carried out.
The RTU request command is:
START T1-T2-T3-T4 (transmission time of 3.5 bytes)
ADDR 01H
CMD 08H
High bit of sub-function code 00H
Low bit of sub-function code 00H
High bit of data content 12H
Low bit of data content ABH
Low bit of CRC ADH
High bit of CRC 14H
END T1-T2-T3-T4 (transmission time of 3.5 bytes)
The RTU response command is:
START T1-T2-T3-T4 (transmission time of 3.5 bytes)
ADDR 01H
CMD 08H
High bit of sub-function code 00H
Low bit of sub-function code 00H
High bit of data content 12H
Low bit of data content ABH
Low bit of CRC ADH
High bit of CRC 14H
END T1-T2-T3-T4 (transmission time of 3.5 bytes)
129
Goodrive200A inverters Communication protocol

9.4.1.4 Command code: 10H, continuous writing

Command code 10H means that if the master writes data to the inverter, the data number
depends on the “data number” in the command code. The Max. continuous reading number
is 16.
For example, write 5000(1388H) to 0004H of the inverter whose slave address is 02H and
50(0032H) to 0005H, the frame structure is as below:
The RTU request command is:
START T1-T2-T3-T4 (transmission time of 3.5 bytes)
ADDR 02H
CMD 10H
High bit of write data 00H
Low bit of write data 04H
High bit of data number 00H
Low bit of data number 02H
Byte number 04H
High bit of data 0004H 13H
Low bit of data 0004H 88H
High bit of data 0005H 00H
Low bit of data 0005H 32H
Low bit of CRC C5H
High bit of CRC 6EH
END T1-T2-T3-T4 (transmission time of 3.5 bytes)
The RTU response command is:
START T1-T2-T3-T4 (transmission time of 3.5 bytes)
ADDR 02H
CMD 10H
High bit of write data 00H
Low bit of write data 04H
High bit of data number 00H
Low bit of data number 02H
Low bit of CRC C5H
High bit of CRC 6EH
END T1-T2-T3-T4 (transmission time of 3.5 bytes)
9.4.2 ASCII mode
9.4.2.1 Command code: 03H (0000 0011), read N words (Word) (max. number for
continuous reading is 16 words)
For instance: As for the inverter whose slave address is 01H, the starting address of internal
storage is 0004, read two words continuously, the structure of this frame is listed as below:

130
Goodrive200A inverters Communication protocol
ASCII master command message ASCII slave response message (the
(the command sent from the master message sent from the inverter to
to the inverter the master)
START ‘:’ START ‘:’
‘0’ ‘0’
ADDR ADDR
‘1’ ‘1’
‘0’ ‘0’
CMD CMD
‘3’ ‘3’
High bit of starting ‘0’ ‘0’
Byte number
address ‘0’ ‘4’
Low bit of starting ‘0’ High bit of data ‘1’
address ‘4’ address 0004H ‘3’
High bit of data ‘0’ Low bit of data ‘8’
number ‘0’ address 0004H ‘8’
Low bit of data ‘0’ High bit of data ‘0’
number ‘2’ address 0005H ‘0’
LRC CHK Hi ‘F’ Low bit of data ‘0’
LRC CHK Lo ‘6’ address 0005H ‘0’
END Hi CR LRC CHK Hi ‘5’
END Lo LF LRC CHK Lo ‘D’
END Hi CR
END Lo LF
9.4.2.2 Command code: 06H (0000 0110), write one word (Word)
For instance: Write 5000 (1388H) to the 0004H address of the inverter whose slave address
is 02H, then the structure of this frame is listed as below:
ASCII master command message ASCII slave response message (the
(the command sent by the master to message sent by the inverter to the
the inverter) master)
START ‘:’ START ‘:’
‘0’ ‘0’
ADDR ADDR
‘2’ ‘2’
‘0’ ‘0’
CMD CMD
‘6’ ‘6’
High bit of write ‘0’ High bit of write ‘0’
data ‘0’ data ‘0’
Low bit of write ‘0’ Low bit of write ‘0’
data ‘4’ data ‘4’
High bit of data ‘1’ High bit of data ‘1’
content ‘3’ content ‘3’
Low bit of data ‘8’ Low bit of data ‘8’
content ‘8’ content ‘8’
LRC CHK Hi ‘5’ LRC CHK Hi ‘5’
LRC CHK Lo ‘9’ LRC CHK Lo ‘9’
END Hi CR END Hi CR
END Lo LF END Lo LF
9.4.2.3 Command code: 08H (0000 1000), diagnose function
Meaning of sub function code:
131
Goodrive200A inverters Communication protocol
Sub function code Instruction
0000 Return inquiry message data
For instance: carry out circuit detection on drive address 01H, the content of inquiry
message word string is the same with response message word string, its format is listed as
below:
ASCII master command message ASCII slave response message (the
(the command sent by the master to message sent by the inverter to the
the inverter) master)
START ‘:’ START ‘:’
‘0’ ‘0’
ADDR ADDR
‘1’ ‘1’
‘0’ ‘0’
CMD CMD
‘8’ ‘8’
High bit of write ‘0’ High bit of write ‘0’
data address ‘0’ data address ‘0’
Low bit of write ‘0’ Low bit of write ‘0’
data address ‘0’ data address ‘0’
High bit of data ‘1’ High bit of data ‘1’
content ‘2’ content ‘2’
Low bit of data ‘A’ Low bit of data ‘A’
content ‘B’ content ‘B’
LRC CHK Hi ‘3’ LRC CHK Hi ‘3’
LRC CHK Lo ‘A’ LRC CHK Lo ‘A’
END Hi CR END Hi CR
END Lo LF END Lo LF
9.4.2.4 Command code: 10H, continuous writing function
Command code 10H means the master write data to the inverter, the number of data being
written is determined by the command “data number”, the max. number of continuous writing
is 16 words.
For instance: Write 5000 (1388H) to 0004H of the inverter whose slave address is 02H, write
50 (0032H) to 0005H of the inverter whose slave address is 02H, then the structure of this
frame is listed as below:
ASCII master command message ASCII slave response message (the
(the command sent by the master to message sent by the inverter to the
the inverter) master)
START ‘:’ START ‘:’
‘0’ ‘0’
ADDR ADDR
‘2’ ‘2’
‘1’ ‘1’
CMD CMD
‘0’ ‘0’
High bit of starting ‘0’ High bit of starting ‘0’
address ‘0’ address ‘0’
Low bit of starting ‘0’ Low bit of starting ‘0’
address ‘4’ address ‘4’
High bit of data ‘0’ High bit of data ‘0’
number ‘0’ number ‘0’

132
Goodrive200A inverters Communication protocol
ASCII master command message ASCII slave response message (the
(the command sent by the master to message sent by the inverter to the
the inverter) master)
Low bit of data ‘0’ Low bit of data ‘0’
number ‘2’ number ‘2’
‘0’ LRC CHK Hi ‘E’
Byte number
‘4’ LRC CHK Lo ‘8’
High bit of data ‘1’ END Hi CR
0004H content ‘3’ END Lo LF
Low bit of data ‘8’
0004H content ‘8’
High bit of data ‘0’
0005H content ‘0’
Low bit of data ‘3’
0005H content ‘2’
LRC CHK Hi ‘1’
LRC CHK Lo ‘7’
END Hi CR
END Lo LF

9.5 The definition of data address

The address definition of the communication data in this part is to control the running of the
inverter and get the state information and relative function parameters of the inverter.

9.5.1 The rules of parameter address of the function codes

The parameter address occupies 2 bytes with the fact that the high bit is in the front and the
low bit is in the behind. The range of high and low byte are: high byte—00~ffH; low byte—
00~ffH. The high byte is the group number before the radix point of the function code and the
low byte is the number after the radix point. But both the high byte and the low byte should
be changed into hex. For example P05.06, the group number before the radix point of the
function code is 05, then the high bit of the parameter is 05, the number after the radix point
05, then the low bit of the parameter is 06, then t he function code address is 0506H and the
parameter address of P10.01 is 0A01H.

Note: P29 group is the factory parameter which can not be read or changed. Some
parameters can not be changed when the inverter is in the running state and some
parameters can not be changed in any state. The setting range, unit and relative instructions
should be paid attention to when modifying the function code parameters.

133
 Goodrive200A inverters Communication protocol
Besides, EEPROM is stocked frequently, which may shorten the usage time of EEPROM.
For users, some functions are not necessary to be stocked on the communication mode.
The needs can be met on by changing the value in RAM. Changing the high bit of the
function code form 0 to 1 can also realize the function. For example, the function code
P00.07 is not stocked into EEPROM. Only by changing the value in RAM can set the
address to 8007H. This address can only be used in writing RAM other than reading. If it is
used to read, it is an invalid address.

9.5.2 The address instruction of other function in MODBUS

The master can operate on the parameters of the inverter as well as control the inverter,
such as running or stopping and monitoring the working state of the inverter.
Below is the parameter list of other functions
Function Address R/W
Data meaning instruction
instruction definition characteristics
0001H:forward running
0002H:reverse running
0003H:forward jogging
Communication 0004H:reverse jogging
2000H W/R
control command 0005H:stop
0006H:coast to stop (emergency stop)
0007H:fault reset
0008H:jogging stop
Communication setting
2001H
frequency(0~Fmax(unit: 0.01Hz))
W/R
PID reference, range(0~1000, 1000
2002H
corresponds to100.0% )
PID feedback, range(0~1000, 1000
2003H W/R
corresponds to100.0% )
Torque setting value (-3000~3000, 1000
2004H corresponds to the 100.0% of the rated current W/R
of the motor)
The address of
The upper limit frequency setting during
the 2005H W/R
forward rotation(0~Fmax(unit: 0.01Hz))
communication n
The upper limit frequency setting during
setting value 2006H W/R
reverse rotation(0~Fmax(unit: 0.01Hz))
The upper limit torque of electromotion torque
2007H (0~3000, 1000 corresponds to the 100.0% of W/R
the rated current of the motor)
The upper limit torque of braking torque
2008H (0~3000, 1000 corresponds to the 100.0% of W/R
the rated current of the motor)
Special control command word
2009H W/R
Bit0~1:=00:motor 1 =01:motor 2
134
 Goodrive200A inverters Communication protocol

Function Address R/W

Data meaning instruction
instruction definition characteristics
=10:motor 3 =11:motor 4
Bit2:=1 torque control =0:speed control
Virtual input terminal command , range:
200AH W/R
0x000~0x1FF
Virtual input terminal command , range:
200BH W/R
0x00~0x0F
Voltage setting value(special for V/F
separation)
200CH W/R
(0~1000, 1000 corresponds to the 100.0% of
the rated voltage of the motor)
AO output setting 1(-1000~1000, 1000
200DH W/R
corresponds to 100.0%)
AO output setting 2(-1000~1000, 1000
200EH W/R
corresponds to 100.0%)
0001H:forward running
0002H:forward running
SW 1 of the
2100H 0003H:stop R
inverter
0004H:fault
0005H: POFF state
Bit0: =0:bus voltage is not established
=1:bus voltage is established
Bi1~2:=00:motor 1 =01:motor 2
=10:motor 3 =11:motor 4
Bit3: =0:asynchronous motor
SW 2 of the
2101H =1:synchronous motor R
inverter
Bit4:=0:pre-alarm without overload
=1:overload pre-alarm
Bit5~ Bit6:=00:keypad control
=01:terminal control
=10:commuincation control
Fault code of the
2102H See the fault type instruction R
inverter
Identifying code
2103H GD200A -----0x0107 R
of the inverter
Operation
3000H Range: 0.00Hz~P00.03 R
frequency
Setting
3001H Range: 0.00Hz~P00.03 R
frequency
Bus voltage 3002H Range: 0~1200V R
Output voltage 3003H Range: 0~1200V R

135
 Goodrive200A inverters Communication protocol

Function Address R/W

Data meaning instruction
instruction definition characteristics
Output current 3004H Range: 0.0~5000.0A R
Operation speed 3005H Range: 0~65535RPM R
Output power 3006H Range: -300.0~300.0% R
Output torque 3007H Range: 0~65535RPM R
Close loop
3008H Range: -100.0%~100.0% R
setting
Close loop
3009H Range: -100.0%~100.0% R
feedback
Input IO state 300AH Range: 0000~00FF R
Output IO state 300BH Range: 0000~00FF R
AI 1 300CH Range: 0.00~10.00V R
AI 2 300DH Range: 0.00~10.00V R
AI 3 300EH Range: 0.00~10.00V R
AI 4 300FH Reserved R
Read high speed
3010H Range: 0.00~50.00kHz R
pulse 1 input
Read high speed
3011H Reserved R
pulse 2 input
Read current
step of the 3012H Range: 0~15 R
multi-step speed
External length 3013H Range: 0~65535 R
External Range: 0~65535
3014H R
counting value
Torque setting 3015H Range: 0~65535 R
Inverter code 3016H R
Fault code 5000H R
R/W characteristics means the function is with read and write characteristics. For example,
“communication control command” is writing chrematistics and control the inverter with
writing command (06H). R characteristic can only read other than write and W characteristic
can only write other than read.
Note: when operate on the inverter with the table above, it is necessary to enable some
parameters. For example, the operation of running and stopping, it is necessary to set
P00.01 to communication running command channel and set P00.02 to MODBUS
communication channel. And when operate on “PID reference”, it is necessary to set P09.00
to “MODBUS communication setting”.
The encoding rules for device codes (corresponds to identifying code 2103H of the inverter)
Code high 8
Meaning Code low 8 bit Meaning
bit
01 GD 0x08 GD35 vector inverters

136
 Goodrive200A inverters Communication protocol

Code high 8
Meaning Code low 8 bit Meaning
bit
0x09 GD35-H1 vector inverters
0x0a GD300 vector inverters
0x0b GD100 simple vector inverters
0x0c GD200A general inverters
0x0d GD10 mini inverters
Note: the code is consisted of 16 bit which is high 8 bits and low 8 bits. High 8 bits mean
the motor type series and low 8 bits mean the derived motor types of the series. For
example, 0110H means Goodrive200A vector inverters.
9.5.3 Fieldbus ratio values
The communication data is expressed by hex in actual application and there is no radix point
in hex. For example, 50.12Hz can not be expressed by hex so 50.12 can be magnified by
100 times into 5012, so hex 1394H can be used to express 50.12.
A non-integer can be timed by a multiple to get an integer and the integer can be called
fieldbus ratio values.
The fieldbus ratio values are referred to the radix point of the setting range or default value in
the function parameter list. If there are figures behind the radix point (n=1), then the fieldbus
n
ratio value m is10 . Take the table as the example:

If there is one figure behind the radix point in the setting range or the default value, then the
fieldbus ratio value is 10. if the data received by the upper monitor is 50, then the
“hibernation restore delay time” is 5.0 (5.0=50÷10).
If MODBUS communication is used to control the hibernation restore delay time as 5.0s.
Firstly, 5.0 can be magnified by 10 times to integer 50 (32H) and then this data can be sent.

After the inverter receives the command, it will change 50 into 5 according to the fieldbus
ratio value and then set the hibernation restore delay time as 5s.
Another example, after the upper monitor sends the command of reading the parameter of
hibernation restore delay time ,if the response message of the inverter is as following:

Because the parameter data is 0032H (50) and 50 divided by 10 is 5, then the hibernation
restore delay time is 5s.
137
Goodrive200A inverters Communication protocol

9.5.4 Fault message response

There may be fault in the communication control. For example, some parameter can only be
read. If a writing message is sent, the inverter will return a fault response message.
The fault message is from the inverter to the master, its code and meaning is as below:
Code Name Meaning
The command from master can not be executed. The reason
maybe:
Illegal
01H 1. This command is only for new version and this version can not
command
realize.
2. Slave is in fault state and can not execute it.
Some of the operation addresses are invalid or not allowed to
Illegal data
02H access. Especially the combination of the register and the
address.
transmitting bytes are invalid.
When there are invalid data in the message framed received by
slave.
03H Illegal value Note: This error code does not indicate the data value to write
exceed the range, but indicate the message frame is an illegal
frame.
Operation The parameter setting in parameter writing is invalid. For example,
04H
failed the function input terminal can not be set repeatedly.
Password The password written to the password check address is not same
05H
error as the password set by P7.00.
In the frame message sent by the upper monitor, the length of the
Data frame
06H digital frame is incorrect or the counting of CRC check bit in RTU is
error
different from the lower monitor.
It only happen in write command, the reason maybe:
Written not 1. The written data exceeds the parameter range.
07H
allowed. 2. The parameter should not be modified now.
3. The terminal has already been used.
The parameter
can not be The modified parameter in the writing of the upper monitor can not
08H
changed be modified during running.
during running
When the upper monitor is writing or reading and the user
Password
09H password is set without password unlocking, it will report that the
protection
system is locked.
The slave uses functional code fields and fault addresses to indicate it is a normal response
or some error occurs (named as objection response). For normal responses, the slave
shows corresponding function codes, digital address or sub-function codes as the response.
For objection responses, the slave returns a code which equals the normal code, but the first
byte is logic 1.
For example: when the master sends a message to the slave, requiring it to read a group of

138
Goodrive200A inverters Communication protocol
address data of the inverter function codes, there will be following function codes:
0 0 0 0 0 0 1 1 (Hex 03H)
For normal responses, the slave responds the same codes, while for objection responses, it
will return:
1 0 0 0 0 0 1 1 (Hex 83H)
Besides the function codes modification for the objection fault, the slave will respond a byte
of abnormal code which defines the error reason.
When the master receives the response for the objection, in a typical processing, it will send
the message again or modify the corresponding order.
For example, set the “running command channel” of the inverter (P00.01, parameter
address is 0001H) with the address of 01H to 03, the command is as following:

But the setting range of “running command channel” is 0~2, if it is set to 3, because the
number is beyond the range, the inverter will return fault response message as below:

Abnormal response code 86H means the abnormal response to writing command 06H; the
fault code is 04H. In the table above, its name is operation failed and its meaning is that the
parameter setting in parameter writing is invalid. For example, the function input terminal can
not be set repeatedly.

9.6 Example of writing and reading

Refer to 10.4.1 and 10.4.2 for the command format.
9.6.1 Example of reading command 03H
Read the state word 1 of the inverter with the address of 01H (refer to table 1). From the
table 1, the parameter address of the state word 1 of the inverter is 2100H.
RTU mode:
The command sent to the inverter:

If the response message is as below:

ASCII mode:
The command sent to the inverter:

If the response message is as below:

139
Goodrive200A inverters Communication protocol

The data content is 0003H. From the table 1, the inverter stops.
9.6.2 Example of writing command 06H
Example 1: make the inverter with the address of 03H to run forward. See table 1, the
address of “communication control command” is 2000H and forward running is 0001. See
the table below.

RTU mode:
The command sent by the master:

If the operation is successful, the response may be as below (the same with the command
sent by the master):

ASCII mode:
The command sent to the inverter:

If the response message is as below:

Example 2: set the Max. Output frequency of the inverter with the address of 03H as100Hz.

See the figures behind the radix point, the fieldbus ratio value of the Max. output frequency
(P00.03) is 100. 100Hz timed by 100 is 10000 and the corresponding hex is 2710H.
RTU mode:
The command sent by the master:

140
Goodrive200A inverters Communication protocol

If the operation is successful, the response may be as below (the same with the command
sent by the master):

ASCII mode:
The command sent to the inverter:

If the response message is as below:

9.6.3 Example of continous writing command 10H

Example 1: make the inverter whose address is 01H run forward at 10Hz. Refer to the
instruction of 2000H and 0001. Set the address of “communication setting frequency” is
2001H and 10Hz corresponds to 03E8H. See the table below.
Function Address R/W
Data meaning instruction
instruction definition characteristics
0001H:forward running
0002H:reverse running
0003H:forward jogging
Communication 0004H:reverse jogging
control 2000H 0005H:stop W/R
command 0006H:coast to stop
(emergency stop)
0007H:fault reset
0008H:jogging stop
Communication setting
2001H frequency(0~Fmax(unit:
The address of
0.01Hz))
communication W/R
PID given, range(0~1000,
setting
2002H 1000 corresponds
to100.0% )
RTU mode:
The command sent to the inverter:

If the response message is as below:

141
Goodrive200A inverters Communication protocol
ASCII mode:
The command sent to the inverter:

If the response message is as below:

Example 2: set the ACC time of 01H inverter as 10s and the DEC time as 20s
ACC Depend on
P00.11 ○
time 1 Setting range of P00.11 and model
P00.12:
DEC Depend on
P00.12 0.0~3600.0s ○
time 1 model
The corresponding address of P00.11 is 000B, the ACC time of 10s corresponds to 0064H,
and the DEC time of 20s corresponds to 00C8H.
RTU mode:
The command sent to the inverter:

If the response message is as below:

ASCII mode:
The command sent to the inverter:

If the response message is as below:

Note: the blank in the above command is for illustration. The blank can not be added in the
actual application unless the upper monitor can remove the blank by themselves.

142
Goodrive200A inverters Appendix A

Technical Data Appendix A

A.1 What this chapter contains

This chapter contains the technical specifications of the inverter, as well as provisions for
fulfilling the requirements for CE and other marks.

A.2 Ratings
A.2.1 Capacity
Inverter sizing is based on the rated motor current and power. To achieve the rated motor
power reference in the table, the rated current of the inverter must be higher than or equal to
the rated motor current. Also the rated power of the inverter must be higher than or equal to
the rated motor power. The power ratings are the same regardless of the supply voltage
within one voltage range.
Note:
1. The maximum allowed motor shaft power is limited to 1.5 · PN. If the limit is exceeded,
motor torque and current are automatically restricted. The function protects the input bridge
of the drive against overload.
2. The ratings apply at ambient temperature of 40 °C
3. It is important to check that in Common DC systems the power flowing through the
common DC connection does not exceed PN.

A.2.2 Derating
The load capacity decreases if the installation site ambient temperature exceeds 40 °C, the
altitude exceeds 1000 meters or the switching frequency is changed from 4 kHz to 8, 12 or
15 kHz.
A.2.2.1 Temperature derating
In the temperature range +40 °C…+50 °C, the rated output current is decreased by 1% for
every additional 1 °C. Refer to the below list for the actual derating.

A.2.2.2 Altitude derating

The device can output rated power if the installation site below 1000m. The output power
decreases if the altitude exceeds 1000 meters. Below is the detailed decreasing range of the
derating:

143
Goodrive200A inverters Appendix A

For 3-phase 200 V drives, the maximum altitude is 3000m above sea level. In altitudes
2000…3000 m, the derating is 1% for every 100 m.
A.2.2.3 Carrier frequency derating
For Goodrive200A series inverters, different power level corresponds to different carrier
frequency range. The rated power of the inverter is based on the factory carrier frequency,
so if it is above the factory value, the inverter needs to derate 10% for every additional 1 kHz
carrier frequency.

A.3 Electric power network specification

AC 3PH 220(-15%)~240(+10%)
Voltage AC 3PH 380(-15%)~440(+10%)
AC 3PH 520(-15%)~690(+10%)
Maximum allowed prospective short-circuit current at the input
Short-circuit power connection as defined in IEC 60439-1 is 100 kA. The drive is
capacity suitable for use in a circuit capable of delivering not more than 100
kA at the drive maximum rated voltage.
Frequency 50/60 Hz ± 5%, maximum rate of change 20%/s

A.4 Motor connection data

Motor type Asynchronous inductance motor
Voltage 0 to U1, 3-phase symmetrical, Umax at the field weakening point
Short-circuit
The motor output is short-circuit proof by IEC 61800-5-1
protection
Frequency 0...400 Hz
Frequency
0.01 Hz
resolution
Current Refer to Ratings
Power limit 1.5 · PN
Field weakening
10...400 Hz
point
Carrier frequency 4, 8, 12 or 15 kHz

A.4.1 EMC compatibility and motor cable length

To comply with the European EMC Directive (standard IEC/EN 61800-3), use the following
maximum motor cable lengths for 4 kHz switching frequency.
144
Goodrive200A inverters Appendix A

All frame sizes Maximum motor cable length, 4 kHz

Second environment (category C3) 30
first environment (category C2) 30
Maximum motor cable length is determined by the drive’s operational factors. Contact your
local INVT representative for the exact maximum lengths when using external EMC filters.

A.5 Applicable standards

The inverter complies with the following standards:
Safety of machinery-safety related parts of control systems -
EN ISO 13849-1: 2008
Part 1: general principles for design
Safety of machinery. Electrical equipment of machines. Part
IEC/EN 60204-1:2006
1: General requirements.
Safety of machinery – Functional safety of safety-related
IEC/EN 62061: 2005 electrical, electronic and programmable electronic control
systems
Adjustable speed electrical power drives systems. Part 3:
IEC/EN 61800-3:2004
EMC requirements and specific test methods
Adjustable speed electrical power drive systems – Part 5-1:
IEC/EN 61800-5-1:2007
Safety requirements – Electrical, thermal and energy
Adjustable speed electrical power drive systems – Part 5-2:
IEC/EN 61800-5-2:2007
Safety requirements. Functional.

A.5.1 CE marking
The CE mark is attached to the drive to verify that the drive follows the provisions of the
European Low Voltage (2006/95/EC) and EMC Directives (2004/108/EC).

A.5.2 Compliance with the European EMC Directive

The EMC Directive defines the requirements for immunity and emissions of electrical
equipment used within the European Union. The EMC product standard (EN 61800-3:2004)
covers requirements stated for drives. See section EMC regulations

A.6 EMC regulations

EMC product standard (EN 61800-3:2004) contains the EMC requirements to the inverter.
First environment: domestic environment (includes establishments connected to a
low-voltage network which supplies buildings used for domestic purposes).
Second environment includes establishments connected to a network not directly supplying
domestic premises.
Four categories of the inverter:
Inverter of category C1: inverter of rated voltage less than 1000 V and used in the first
environment.
Inverter of category C2: inverter of rated voltage less than 1000 V other than pins, sockets
and motion devices and intended to be installed and commissioned only by a professional
electrician when used in the first environment.
Note: IEC/EN 61800-3 in EMC standard doesn’t limit the power distribution of the inverter,

145
Goodrive200A inverters Appendix A
but it defines the step, installation and commission. The professional electrician has
necessary skills in installing and/or commissioning power drive systems, including their EMC
aspects.
Inverter of category C3: inverter of rated voltage less than 1000 V and used in the second
environment other than the first one.
Inverter of category C4: inverter of rated voltage more than 1000 V or the rated current is
above or equal to 400A and used in the complicated system in second environment.

A.6.1 Category C2
The emission limits are complied with the following provisions:
1. The optional EMC filter is selected according to the options and installed as specified in
the EMC filter manual.
2. The motor and control cables are selected as specified in this manual.
3. The drive is installed according to the instructions reference in this manual.
4. For the maximum motor cable length with 4 kHz switching frequency, see EMC
compatibility and motor cable length

 In a domestic environment, this product may cause radio inference, in

which case supplementary mitigation measures may be required.

A.6.2 Category C3
The immunity performance of the drive complies with the demands of IEC/EN 61800-3,
second environment.
The emission limits are complied with the following provisions:
1. The optional EMC filter is selected according to the options and installed as specified in
the EMC filter manual.
2. The motor and control cables are selected as specified in this manual.
3. The drive is installed according to the instructions reference in this manual.
4. For the maximum motor cable length with 4 kHz switching frequency, see EMC
compatibility and motor cable length
 A drive of category C3 is not intended to be used on a low-voltage
public network which supplies domestic premises. Radio frequency
interference is expected if the drive is used on such a network.

146
Goodrive200A inverters Appendix B

Dimension Drawings Appendix B

B.1 What this chapter contains

Dimension drawings of the Goodrive200A are shown below. The dimensions are reference
in millimeters and inches.

B.2 Keypad structure

B.2.1 Structure chart

keyboard without bracket mounting

hole size

B.2.2 Installation chart

Note: The external keypad can be fix by M3 screws directly or the installation bracket. The
installation bracket for inverters of 0.75~30kW is optional and the installtaion bracket for
inverters of 37~500kW is optional or substitutive by the external standard one.

Installation bracket of the key (0.75~500kW)(optional)

键盘安装架 客户安装尺寸

Installation bracket of the key (37~500kW)(standard)

147
Goodrive200A inverters Appendix B

B.3 Inverter chart

B.3.1 Wall mounting

0.75-15kW wall mounting

18.5-30kW wall mounting

37-110kW wall mounting

132-200kW wall mounting

148
Goodrive200A inverters Appendix B

220-315kW wall mounting

Installation dimension (unit: mm)
Installation
Model W1 W2 H1 H2 D1
hole
0.75kW ~2.2kW 126 115 186 175 174.5 5
4kW~5.5kW 146 131 256 243.5 181 6
7.5kW~15kW 170 151 320 303.5 216 6
18.5kW 230 210 342 311 216 6
22kW~30kW 255 237 407 384 245 7
37kW~55kW 270 130 555 540 325 7
75kW~110kW 325 200 680 661 365 9.5
132kW~200kW 500 180 870 850 360 11
220kW~315kW 680 230 960 926 379.5 13

B.3.2 Flange mounting

0.75-15kW flange mounting

18.5-30kW flange mounting

149
Goodrive200A inverters Appendix B

37-110kW flange mounting

132-200kW flange mounting

Installation dimension (unit: mm)

Installation
Model W1 W2 W3 W4 H1 H2 H3 H4 D1 D2
hole
0.75kW~2.2kW 150.2 115 130 7.5 234 220 190 13.5 155 65.5 5
4kW~5.5kW 170.2 131 150 9.5 292 276 260 6 167 84.5 6
7.5kW~15kW 191.2 151 174 11.5 370 351 324 12 196.3 113 6
18.5kW 250 210 234 12 375 356 334 10 216 108 6
22kW~30kW 275 237 259 11 445 426 404 10 245 119 7
37kW~55kW 270 130 261 65.5 555 540 516 17 325 167 7
75kW~110kW 325 200 317 58.5 680 661 626 23 363 182 9.5
132kW~200kW 500 180 480 60 870 850 796 37 358 178.5 11

150
Goodrive200A inverters Appendix B

B.3.3 Floor mounting

220-315kW floor mounting

50-500kW floor mounting

Installation
Model W1 W2 W3 W4 H1 H2 D1 D2
hole
220kW~315kW 750 230 714 680 1410 1390 380 150 13\12
350kW~500kW 620 230 573 \ 1700 1678 560 240 22\12

151
Goodrive200A inverters Appendix C

Peripheral Options and Parts Appendix C

C.1 What this chapter contains

This chapter describes how to select the options and parts of Goodrive200A series.
C.2 Peripheral wiring
Below is the peripheral wiring of Goodrive200A series inverters.

Note:
1. The inverters (≤15kW) have standard film keypad and the inverters (≥18.5kW) have
standard LED keypad.
2．The inverter below 30kW (including 30kW) are embedded with braking unit.
3. Only the inverter above 37kW (including 37kW) have P1 terminal and are connected
with DC reactors.
4. The braking units apply standard braking unit DBU series in. Refer to the instruction of
DBU for detailed information.
Pictures Name Descriptions

Cables Device to transfer the electronic signals

Prevent from electric shock and protect the

power supply and the cables system from
overcurrent when short circuits occur.
Breaker (Please select the breaker with the
function of reducing high order harmonic
and the rated sensitive current to 1 inverter
should be above 30mA).
152
Goodrive200A inverters Appendix C

Pictures Name Descriptions

This device is used to improve the power

Input reactor
factor of the input side of the inverter and
control the higher harmonic current.
The inverter above 37kW (including 37kW)
DC reactor
can be connected with DC reactor.

Control the electromagnetic interference

generated from the inverter, please install
Input filter
close to the input terminal side of the
inverter.
Shorten the DEC time
The inverters below 30kW(including 30kW)
Braking unit or resistors only need braking resistors and the
inverters above 37kW(including 37 kW)
or
need braking units
Control the interference from the output
Output filter side of the inverter and please install close
to the output terminals of the inverter.
Prolong the effective transmitting distance
of the inverter to control the sudden high
Output reactor
voltage when switching on/off the IGBT of
the inverter.

C.3 Power supply

Please refer to Electronical Installation.

 Check that the voltage degree of the inverter complies with the voltage
of the supply power voltage.

C.4 Cables
C.4.1 Power cables
Dimension the input power and motor cables according to local regulations.
• The input power and the motor cables must be able to carry the corresponding load
currents.
• The cable must be rated for at least 70 °C maximum permissible temperature of the
conductor in continuous use.
• The conductivity of the PE conductor must be equal to that of the phase conductor
(same cross-sectional area).
• Refer to chapter Technical Data for the EMC requirements.
A symmetrical shielded motor cable (see the figure below) must be used to meet the EMC
requirements of the CE.
A four-conductor system is allowed for input cabling, but a shielded symmetrical cable is

153
Goodrive200A inverters Appendix C
recommended. Compared to a four-conductor system, the use of a symmetrical shielded
cable reduces electromagnetic emission of the whole drive system as well as motor bearing
currents and wear.

Note: A separate PE conductor is required if the conductivity of the cable shield is not
sufficient for the purpose.
To function as a protective conductor, the shield must have the same cross-sectional area as
the phase conductors when they are made of the same metal.
To effectively suppress radiated and conducted radio-frequency emissions, the shield
conductivity must be at least 1/10 of the phase conductor conductivity. The requirements are
easily met with a copper or aluminum shield. The minimum requirement of the motor cable
shield of the drive is shown below. It consists of a concentric layer of copper wires. The
better and tighter the shield, the lower the emission level and bearing currents.

C.4.2 Control cables

All analog control cables and the cable used for the frequency input must be shielded. Use a
double-shielded twisted pair cable (Figure a) for analog signals. Employ one individually
shielded pair for each signal. Do not use common return for different analog signals.

A double-shielded cable is the best alternative for low-voltage digital signals, but a
single-shielded or unshielded twisted multi-pair cable (Figure b) is also usable. However, for
frequency input, always use a shielded cable.
The relay cable needs the cable type with braided metallic screen.
The keypad needs to connect with cables. It is recommended to use the screen cable on
complex electrical magnetic condition.
Note: Run analog and digital signals in separate cables.
Do not make any voltage tolerance or insulation resistance tests (for example hi-pot or
megger) on any part of the drive as testing can damage the drive. Every drive has been
tested for insulation between the main circuit and the chassis at the factory. Also, there are
voltage-limiting circuits inside the drive which cut down the testing voltage automatically.
Check the insulation of the input power cable according to local regulations before

154
Goodrive200A inverters Appendix C
connecting to the drive.
Note: Check the insulation of the input power cables according to local regulations
before connecting the cables.

Recommended cable size(mm2) Screw

Terminal Tightening
The inverter R,S,T
PE P1(+) PB(+)(-) screw torque
U,V,W
size (Nm)
GD200A -0R7G-4 2.5 2.5 2.5 2.5 M4 1.2~1.5
GD200A -1R5G-4 2.5 2.5 2.5 2.5 M4 1.2~1.5
GD200A -2R2G-4 2.5 2.5 2.5 2.5 M4 1.2~1.5
GD200A
2.5 2.5 2.5 2.5 M4 1.2~1.5
-004G/5R5P-4
GD200A
4 4 2.5 2.5 M5 2~2.5
-5R5G/7R5P-4
GD200A -7R5G/011P-4 6 6 4 2.5 M5 2~2.5
GD200A -011G/015P-4 10 10 6 4 M5 2~2.5
GD200A -015G/018P-4 10 10 10 4 M5 2~2.5
GD200A -018G/022P-4 16 16 10 6 M6 4~6
GD200A -022G/030P-4 25 16 16 10 M6 4~6
GD200A -030G/037P-4 25 16 16 10 M8 9~11
GD200A -037G/045P-4 35 16 25 16 M8 9~11
GD200A -045G/055P-4 50 25 35 25 M8 9~11
GD200A -055G/075P-4 70 35 50 25 M10 18~23
GD200A -075G/090P-4 95 50 70 35 M10 18~23
GD200A -090G/110P-4 120 70 95 35 M10 18~23
GD200A -110G/132P-4 150 70 120 70 M12 31~40
GD200A -132G/160P-4 185 95 150 95 M12 31~40
GD200A -160G/185P-4 240 95 185 50 M12 31~40
GD200A -185G/200P-4 120*2P 150 95*2P 50 M12 31~40
GD200A -200G/220P-4 120*2P 150 95*2P 50 M12 31~40
GD200A -220G/250P-4 150*2P 150 95*2P 50 M12 31~40
GD200A -250G/280P-4 150*2P 150 120*2P 95 M12 31~40
GD200A -280G/315P-4 185*2P 185 120*2P 95 M12 31~40
GD200A -315G/350P-4 185*2P 185 120*2P 95 M12 31~40
GD200A -350G/400P-4 95*4P 95*2P 150*2P 120 M12 31~40
GD200A -400G-4 95*4P 95*2P 150*2P 120 M12 31~40
GD200A -500G-4 120*4P 95*2P 95*4P 120 M12 31~40
Note:
1. It is appropriate to use the recommended cable size under 40℃ and rated current. The
wiring distance should be no more than 100m.
2. Terminals P1, (+), PB and (-) connects the DC reactor options and parts.

155
Goodrive200A inverters Appendix C

C.4.3 Routing the cables

Route the motor cable away from other cable routes. Motor cables of several drives can be
run in parallel installed next to each other. It is recommended that the motor cable, input
power cable and control cables are installed on separate trays. Avoid long parallel runs of
motor cables with other cables to decrease electromagnetic interference caused by the rapid
changes in the drive output voltage.
Where control cables must cross power cables make sure that they are arranged at an angle
as near to 90 degrees as possible.
The cable trays must have good electrical bonding to each other and to the grounding
electrodes. Aluminum tray systems can be used to improve local equalizing of potential.
A figure of the cable routing is shown below.

C.4.4 Checking the insulation

Check the insulation of the motor and motor cable as follows:
1. Check that the motor cable is connected to the motor and disconnected from the drive
output terminals U, V and W.
2. Measure the insulation resistance between each phase conductor and the Protective
Earth conductor using a measuring voltage of 500 V DC. For the insulation resistance of
other motors, please consult the manufacturer’s instructions.
Note: Moisture inside the motor casing will reduce the insulation resistance. If moisture is
suspected, dry the motor and repeat the measurement.

C.5 Breaker, electromagnetic contactor and leakage protection

switch
Due to the inverter output high frequency PWM voltage waveform, and the existance of
distributed capacitance between IGBT and heatsink in internal inverter and the distributed
capacitance between motor stator and rotor will cause the inverter inevitably generate
high-frequency leakage current to ground. The high-frequency leakage current will back flow
to grid through the earth to interference the leakage protection switch, thus causing the
leakage protection switch malfunction. This is due to the inverter output voltage
characteristics inherent in the decision.
To ensure the stability of the system, it is recommended to use the inverter dedicated
leakage protection switch which rated residual operation current 30mA or more(for example,
corresponds to IEC60755 Type B). If you are not using the inverter dedicated leakage
protection switch caused by malfunction, try to reduce the carrier frequency, or replace the
electromagnetic leakage protection switch which rated residual operating current of 200mA

156
Goodrive200A inverters Appendix C
or more.
It is necessary to add fuse for the avoidance of overload.
It is appropriate to use a breaker (MCCB) which complies with the inverter power in the
3-phase AC power and input power and terminals (R, S and T). The capacity of the inverter
should be 1.5-2 times of the rated current.
 Due to the inherent operating principle and construction of circuit
breakers, independent of the manufacturer, hot ionized gases may
escape from the breaker enclosure in case of a short-circuit. To ensure
safe use, special attention must be paid to the installation and
placement of the breakers. Follow the manufacturer’s instructions.

Rated current of the

Inverter Breaker (A) Fuse (A)
reactor (A)
GD200-0R7G-4 10 16 12
GD200-1R5G-4 10 16 12
GD200-2R2G-4 16 16 12
GD200-004G/5R5P-4 16 25 12
GD200-5R5G/7R5P-4 25 32 25
GD200-7R5G/011P-4 40 40 25
GD200-011G/015P-4 50 50 40
GD200-015G/018P-4 63 63 40
GD200-018G/022P-4 63 80 50
GD200-022G/030P-4 80 100 65
GD200-030G/037P-4 100 125 80
GD200-037G/045P-4 125 160 95
GD200-045G/055P-4 160 160 115
GD200-055G/075P-4 160 200 150
GD200-075G/090P-4 250 250 185
GD200-090G/110P-4 250 315 225
GD200-110G/132P-4 315 315 265
GD200-132G/160P-4 350 400 330
GD200-160G/185P-4 400 500 400
GD200-185G/200P-4 500 630 500
GD200-200G/220P-4 500 630 500
GD200-220G/250P-4 630 630 500
GD200-250G/280P-4 630 800 630
GD200-280G/315P-4 700 800 630
GD200-315G/350P-4 800 1000 780
GD200-350G/400P-4 800 1000 780
GD200-400G-4 1000 1250 780
GD200-500G-4 1200 1250 980

157
Goodrive200A inverters Appendix C

C.6 Reactors
If the distance between the inverter and the motor is longer than 50m, frequent overcurrent
protection may occur to the inverter because of high leakage current caused by parasitic
capacitance effects from the long cables to the ground. In order to avoid the damage of the
motor insulation, it is necessary to add reactor compensation. If the distance between the
inverter and motor is 50~100m, see the table below for model selection; if it exceeds 100m,
consult with INVT technical support.
The power of the inverter Input reactor DC reactor Output reactor
GD200A -0R7G-4 ACL2-1R5-4 / OCL2-1R5-4
GD200A -1R5G-4 ACL2-1R5-4 / OCL2-1R5-4
GD200A -2R2G-4 ACL2-2R2-4 / OCL2-2R2-4
GD200A -004G/5R5P-4 ACL2-004-4 / OCL2-004-4
GD200A -5R5G/7R5P-4 ACL2-5R5-4 / OCL2-5R5-4
GD200A -7R5G/011P-4 ACL2-7R5-4 / OCL2-7R5-4
GD200A -011G/015P-4 ACL2-011-4 / OCL2-011-4
GD200A -015G/018P-4 ACL2-015-4 / OCL2-015-4
GD200A -018G/022P-4 ACL2-018-4 / OCL2-018-4
GD200A -022G/030P-4 ACL2-022-4 / OCL2-022-4
GD200A -030G/037P-4 ACL2-030-4 / OCL2-030-4
GD200A -037G/045P-4 ACL2-037-4 DCL2-037-4 OCL2-037-4
GD200A -045G/055P-4 ACL2-045-4 DCL2-045-4 OCL2-045-4
GD200A -055G/075P-4 ACL2-055-4 DCL2-055-4 OCL2-055-4
GD200A -075G/090P-4 ACL2-075-4 DCL2-075-4 OCL2-075-4
GD200A -090G/110P-4 ACL2-090-4 DCL2-090-4 OCL2-090-4
GD200A -110G/132P-4 ACL2-110-4 DCL2-110-4 OCL2-110-4
GD200A -132G/160P-4 ACL2-132-4 DCL2-132-4 OCL2-132-4
GD200A -160G/185P-4 ACL2-160-4 DCL2-160-4 OCL2-160-4
GD200A -185G/200P-4 ACL2-200-4 DCL2-200-4 OCL2-200-4
GD200A -200G/220P-4 ACL2-200-4 DCL2-200-4 OCL2-200-4
GD200A -220G/250P-4 ACL2-250-4 DCL2-280-4 OCL2-250-4
GD200A -250G/280P-4 ACL2-250-4 DCL2-280-4 OCL2-250-4
GD200A -280G/315P-4 ACL2-280-4 DCL2-280-4 OCL2-280-4
GD200A -315G/350P-4 ACL2-315-4 DCL2-315-4 OCL2-315-4
GD200A -350G/400P-4 Standard DCL2-350-4 OCL2-350-4
GD200A -400G-4 Standard DCL2-400-4 OCL2-400-4
GD200A -500G-4 Standard DCL2-500-4 OCL2-500-4
Note:
1. The rated derate voltage of the input reactor is 2%±15%.
2. The power factor of the input side is above 90% after adding DC reactor.
3. The rated derate voltage of the output reactor is 1%±15%.
4. Above options are external, the customer should indicate when purchasing.

158
Goodrive200A inverters Appendix C

C.7 Filters
C3 filters are optional for Goodrive200A 0.75~110kW inverters. If you need to configure C3
filters, connect them to J10.

Filters for Goodrive200A series inverters

The inverter Input filter Output filter
GD200A -0R7G-4
GD200A -1R5G-4 FLT-P04006L-B FLT-L04006L-B
GD200A -2R2G-4
GD200A-004G/5R5P-4
FLT-P04016L-B FLT-L04016L-B
GD200A-5R5G/7R5P-4
GD200A -7R5G/011P-4
FLT-P04032L-B FLT-L04032L-B
GD200A -011G/015P-4
GD200A -015G/018P-4
FLT-P04045L-B FLT-L04045L-B
GD200A -018G/022P-4
GD200A -022G/030P-4
FLT-P04065L-B FLT-L04065L-B
GD200A -030G/037P-4
GD200A -037G/045P-4
FLT-P04100L-B FLT-L04100L-B
GD200A -045G/055P-4
GD200A -055G/075P-4
FLT-P04150L-B FLT-L04150L-B
GD200A -075G/090P-4
GD200A -090G/110P-4
GD200A -110G/132P-4 FLT-P04240L-B FLT-L04240L-B
GD200A -132G/160P-4
GD200A -160G/185P-4
GD200A -185G/200P-4 FLT-P04400L-B FLT-L04400L-B
GD200A -200G/220P-4
GD200A -220G/250P-4
FLT-P04600L-B FLT-L04600L-B
GD200A -250G/280P-4
159
Goodrive200A inverters Appendix C

The inverter Input filter Output filter

GD200A -280G/315P-4
GD200A -315G/350P-4
GD200A -350G/400P-4 FLT-P04800L-B FLT-L04800L-B
GD200A -400G-4
GD200A -500G-4 FLT-P041000L-B FLT-L041000L-B
Note: The input EMI meet the requirement of C2 after adding input filters.

C.8 Braking system

C.8.1 Select the braking components
It is appropriate to use braking resistor or braking unit when the motor brakes sharply or the
motor is driven by a high inertia load. The motor will become a generator if its actual rotating
speed is higher than the corresponding speed of the reference frequency. As a result, the
inertial energy of the motor and load return to the inverter to charge the capacitors in the
main DC circuit. When the voltage increases to the limit, damage may occur to the inverter. It
is necessary to apply braking unit/resistor to avoid this accident happens.
 Only qualified electricians are allowed to design, install, commission
and operate on the inverter.
 Follow the instructions in “warning” during working. Physical injury or
death or serious property may occur.
 Only qualified electricians are allowed to wire. Damage to the inverter
or braking options and part may occur. Read carefully the instructions of
braking resistors or units before connecting them with the inverter.
 Do not connect the braking resistor with other terminals except for PB
and (-). Do not connect the braking unit with other terminals except for (+)
and (-). Damage to the inverter or braking circuit or fire may occur.
 Connect the braking resistor or braking unit with the inverter according
to the diagram. Incorrect wiring may cause damage to the inverter or
other devices.
Goodrive200A series inverters below 30kW (including 30kW) need internal braking units and
the inverters above 37kW need external braking unit. Please select the resistance and
power of the braking resistors according to actual utilization.
Note:
Select the resistor and power according to the provided data.
The braking torque may increase because of the raising of braking resistor. The below table
is calculated at 100% of the braking torque, 10%, 50% and 80%of the braking usage ratio.
The user can select according to the actual working.
Refer to the operation instructions of braking units when using external units for right setting
of voltage degree. Otherwise normal operation of the inverter may be impacted.

160
Goodrive200A inverters Appendix C

100% of The consumed power of the Mini

Braking unit braking braking resistor Braking
The inverter
type torque 10% 50% 80% Resistor
(Ω) braking braking braking (Ω)
GD200A -0R7G-4 653 0.1 0.6 0.9 240
GD200A -1R5G-4 326 0.23 1.1 1.8 170
GD200A -2R2G-4 222 0.33 1.7 2.6 130
GD200A-004G/5R5P-4 122 0.6 3 4.8 80
GD200A-5R5G/7R5P-4 89 0.75 4.1 6.6 60
Internal braking
GD200A -7R5G/011P-4 65 1.1 5.6 9 47
unit
GD200A -011G/015P-4 44 1.7 8.3 13.2 31
GD200A -015G/018P-4 32 2 11 18 23
GD200A -018G/022P-4 27 3 14 22 19
GD200A -022G/030P-4 22 3 17 26 17
GD200A -030G/037P-4 17 5 23 36 17
GD200A -037G/045P-4 DBU100H-060-4 13 6 28 44 11.7
GD200A -045G/055P-4 10 7 34 54
GD200A -055G/075P-4 DBU100H-110-4 8 8 41 66 6.4
GD200A -075G/090P-4 6.5 11 56 90
GD200A -090G/110P-4 5.4 14 68 108
DBU100H-160-4 4.4
GD200A -110G/132P-4 4.5 17 83 132
GD200A -132G/160P-4 DBU100H-220-4 3.7 20 99 158 3.2
GD200A -160G/185P-4 3.1 24 120 192
GD200A -185G/200P-4 DBU100H-320-4 2.8 28 139 222 2.2
GD200A -200G/220P-4 2.5 30 150 240
GD200A -220G/250P-4 2.2 33 165 264
DBU100H-400-4 1.8
GD200A -250G/280P-4 2.0 38 188 300
GD200A -280G/315P-4 3.6*2 21*2 105*2 168*2
GD200A -315G/350P-4 Two 3.2*2 24*2 118*2 189*2
2.2*2
GD200A -350G/400P-4 DBU100H-320-4 2.8*2 27*2 132*2 210*2
GD200A -400G-4 2.4*2 30*2 150*2 240*2
Two
GD200A -500G-4 2*2 38*2 186*2 300*2 1.8*2
DBU100H-400-4

 Never use a brake resistor with a resistance below the minimum value
specified for the particular drive. The drive and the internal chopper are
not able to handle the overcurrent caused by the low resistance.

 Increase the power of the braking resistor properly in the frequent

braking situation (the frequency usage ratio is more than 10%).

161
Goodrive200A inverters Appendix C

C.8.2 Select the brake resistor cables

Use a shielded cable to the resistor cable.

C.8.3 Place the brake resistor

Install all resistors in a place where they will cool.
 The materials near the brake resistor must be non-flammable. The
surface temperature of the resistor is high. Air flowing from the resistor
is of hundreds of degrees Celsius. Protect the resistor against contact.
Installation of the braking resistor:
 The inverters below30kW (including 30kW) only needs external braking
resistors.
 PB and (+) are the wiring terminals of the braking resistors.

Installation of braking units:

 The inverters above 37kW (including 370kW) only needs external
braking units.
 (+), (-) are the wiring terminals of the braking units.
 The wiring length between the (+),(-) terminals of the inverter and the
(+),(-) terminals of the braking units should be no more than 5m,and the
distributing length among BR1 and BR2 and the braking resistor
terminals should be no more than 10m.
Signal installation is as below:

162
Goodrive200A inverters Appendix C

C.9 Other optional parts

Optional
No. Instruction Picture
part
Needed for the flange installation of
Flange
1.5~30kW inverters
1 installation
Not needed for the flange installation
bracket
of 37~200kW inverters

Optimal for 220~315kW inverters

Installation
2 An input AC/DC reactor and output
base
AC reactor can be put in the base.

Use the screw or installation bracket

Installation to fix the external keypad.
3
bracket Optimal for 1.5~30kW inverters ands
standard for 37~500kW inverters

Protect the internal circuit in serious

environment. Derate when selecting
4 Side cover
the cover. Please contact INVT for
detailed information.

Support several languages,

parameters copy, high-definition
5 LCD Keypad
display and the installation dimension
is compatible with the LED keypad.

6 LED keypad 0.75~15kW inverter optional.

163
Goodrive200A inverters Appendix D

Further Information Appendix D

D.1 Product and service inquirie

Address any inquiries about the product to your local INVT offices, quoting the type
designation and serial number of the unit in question. A listing of INVT sales, support and
service contacts can be found by navigating to www.invt.com.cn.

D.2 Feedback on INVT inverters manuals

Your comments on our manuals are welcome. Go to www.invt.com.cn and select Online
Feedback of Contact Us.

D.3 Document library on the internet

You can find manuals and other product documents in PDF format on the Internet. Go to
www.invt.com.cn and select Service and Support of Document Download.

164
66001- 00342

201701(V2.1)