DYNA

Product Information Power Controls

DYNA 8000 GOVERNOR SYSTEM

GENERAL

The DYNA 8000 system will provide an engine governor for

speed and power control of piston and gas turbine engines
or steam and water turbines.

The actuator is basically a simple, proportional, electric

solenoid having a sliding armature whose magnetic force is
proportional to input coil current. Balanced between the
force of its return spring and the magnetic force, the arma-
ture glides on anti-friction bearings, providing a hysteresis-
free linear movement. Linear motion is converted to an
n t y
output shaft rotation by a bell crank.
e n l
u m O
TYPICAL APPLICATIONS
o c
AVAILABLE
e
MODELS
•
•
Speed governing
Remote throttle control
D n c Actuators:
• Test stand throttle control
d r e Part No.
• Generator sets

l e e DYNC-11020-000-0-12 Standard Clockwise

•
•
Power carts
Pump sets l e f DYNC-11020-000-0-24 Output Shaft Rotation

r o R DYNC-11024-000-0-12 Standard Counter Clockwise

STANDARD FEATURES
n t a l
DYNC-11024-000-0-24 Output Shaft Rotation

• All electric
c o i c Controllers: Speed Controllers
•
•
All engine compatibility
n
Mounts in any position
o r Part No. Input Signal Frequency

U t DYN1 -10652-000-0-12/24 250-1200 Hz

is
• Engine mounted (actuator only)
DYN1 -10653-000-0-12/24 1200-2500 Hz
• High reliability due to few moving parts

H
DYN1 -10654-000-0-12/24 2500-5000 Hz
• Proportional actuator
DYN1 -10656-000-0-12/24 5000-9500 Hz
•
•
o r
No hydraulic or oil line
No special maintenance
•
F
Spring returns output shaft to minimum position on removal
of power or loss of magnetic pickup signal
DYN1 -10682-000-0-12/24
DYN1 -10683-000-0-12/24
250-1200 Hz
1200-2500 Hz
• Precise repeatability DYN1 -10684-000-0-12/24 2500-5000 Hz
DYN1 -10686-000-0-12/24 5000-9500 Hz

Controllers: Conforming to Specifications

Part No. Input Signal Frequency

DYN1 -10652-001-0-12/24 250-1200 Hz
DYN1 -10653-001-0-12/24 1200-2500 Hz
DYN1 -10654-001-0-12/24 2500-5000 Hz
DYN1 -10656-001-0-12/24 5000-9500 Hz
DYN1 -10682-001-0-12/24 250-1200 Hz
DYN1 -10683-001-0-12/24 1200-2500 Hz
DYN1 -10684-001-0-12/24 2500-5000 Hz
DYN1 -10686-001-0-12/24 5000-9500 Hz
F-22030-8
SPECIFICATIONS (ACTUATOR) INPUT SIGNAL FREQUENCY
Operating Voltage: Engine RPM x Number of Gear
Input Signal Teeth on Flywheel
12 VDC or 24 VDC, ± 20% Frequency in Hertz
= 60 Seconds

Sealed Unit:
Oil, water and dust tight Select your controller for the correct input signal frequency
range generated by the magnetic pickup at the maximum
Connection: engine operated (RPM) speed.
Terminal strip

Actuator Ambient Operating Temperature:

-65°F (-55°C) to +255°F (+125°C)

Mechanical Vibration:
5 to 500 Hz, Curve F, per Mil-Std. 810C, Method 514-2.
DYNA 8000 Actuators

Work Joules 1.2

SPECIFICATIONS (CONTROLLER) t
Foot-Pounds
n y
1.0

e
Newton-Meters

n l 1.4

m
Operating Voltages: Torque Pound-Foot 1.0
12 VDC or 24 VDC, ± 20% Output

c u Rotary
O 35°

e
Weight Kilograms 5
Circuit Boards:
o c
Pounds 11.0
Are covered with a heavy conformal coating for moisture and
vibration protection. D e n
Current @ 12 VDC Maximum Amperes @ Stall 12.5
Nominal Steady State Amperes 3.5

ed r
Current @ 24 VDC Maximum Amperes @ Stall 9.5

l e
ef
Connection: Nominal Steady State Amperes 2.5
Terminal Strip
o l Nominal Response Time for 63% of Stroke

R
(Seconds) 0.030
Controller Ambient Operating Temperature:
tr l
on a
-40°F (-40°C) to +180°F (+85°C).

i c
nc r
Temperature Stability:
Better than ± 0.5 percent over a temperature range of
-40°F (-40°C) to 167°F (+75°C)
U t o
is DYNA 8000 Controllers
H
Steady State Speed Band:
± 0.25% Output Nominal Quiescent Current 80 ma

Adjustments: o r Current@ 12 VDC Maximum Amperes @ Stall 13 amps

F
Output Nominal Quiescent Current 80 ma
Speed, Gain, Integral and Droop. Current@ 24 VDC Maximum Amperes @ Stall 13 amps
Weight Kilograms 0.863
Mechanical Vibration: Pounds 1.9
Withstands the following vibration without failure or degraded
performance: 0.06 inch double amplitude at 5 to 18 Hz; 1 G at
18 to 30 Hz; 0.02 inch double amplitude at 30 to 48 Hz; 2.5 G’s
at 48 to 70 Hz.

2
DIMENSIONS — DYNA 8000 CONTROLLER

n t y
e n l
Chassis
Ground
u m O
Screw

o c e
D n c
e
l ed e r
l ef
Dimensions are MM except

o R
as otherwise noted.

tr
Dimensions in [ ] in inches.

l
on i c a
nc r *Shielded Cable — Should be purchased from

U t o Barber-Colman or customer should purchase a

cable with a wrapped mylar supported aluminum

is
foil shield with a drain wire.

H **Remote Speed Potentiometer and 499K OHM

Resistor — DYNS 10000

o r †The 5K Remote Speed Potentiometer can be

F wired two different ways.

1. As shown by the solid line from the wiper of

WIRING DIAGRAM FOR CONTROLLERS the 5K Potentiometer and then connected
to Terminal #9. (No resistor required.) Ad-
Failsafe justable range is approximately ± 5% at
1800 RPM.
TP1 TP2

2. As shown by the dashed line from the wiper

of the 5K Potentiometer through Resistor R
1 2 3 4 5 6 7 8 9 10 11 and then connected to Terminal #8. Reduc-

AAAAAA
AAAAA ing the value of R increases the remote

AAAAAAAA ILS
adjustable speed range.

AAAAAAAAA
+8V +4V
External
Speed
Chassis
Gnd
Blk Wht

Adjust Screw
+ - Chassis
Actuator Gnd Magnetic Pick-up
Battery Screw

3
INSTALLATION DRAWINGS

(DYNC 11020-300)
Side Mounted
Actuator

Clockwise
Rotation

(DYNC 11020-000)
Base Mounted
Actuator
n t y
e n l
Clockwise
Rotation u m O
o c e
D n c
e
l ed e r
o l ef
R
(DYNC 11024-000)
tr l
on a
Base Mounted
Actuator
i c
Counter- nc o r
clockwise U t
Rotation
is
H
o r
F
Barber-Colman Company
Aerospace & Power Controls Division
DYNA Product Group

1354 Clifford Avenue Telephone (815) 637-3000

P.O. Box 2940 Facsimile (815) 877-0150
Loves Park, IL 61132-2940 CAUTION
United States of America As a safety measure, the engine should be equipped with an
independent overspeed shutdown device in the event of
In Europe contact: Barber-Colman GmbH failure which may render the governor inoperative.
Am Neuen Rheinhafen 4, D-67346 Speyer, Germany
Telephone 06232 29903, Facsimile 06232 299155
NOTE
In Japan contact: Ranco Japan Ltd. Barber-Colman believes that all information provided herein is
Shiozaki Bldg. 7-1, 2-chome, Hirakawa-Cho, Chiyoda-Ku correct and reliable and reserves the right to update at any
time. Barber-Colman does not assume any responsibility for
Tokyo 102, Japan its use unless otherwise expressly undertaken.
Telephone 3261 4293, Facsimile 3264 4691

A Siebe Group Company F-22030-8