Sfcxx140Gexd - SFP Dual Fibre CWDM: CWDM / 140Km / Gigabit Ethernet

Datasheet
SFCxx140GE0D_RevA.docx
SFCxx140GExD – SFP Dual Fibre CWDM

CWDM / 140km / Gigabit Ethernet
For your product safety, please read the following information carefully before any manipulation of the transceiver:
ESD
This transceiver is specified as ESD threshold 1kV for SFI pins and 2kV for all others electrical input pins, tested per MIL-STD-883G, Method 3015.4 /JESD22-
A114-A (HBM). However, normal ESD precautions are still required during the handling of this module.
LASER SAFETY
This is a Class1 Laser Product according to IEC 60825-1:2007. This product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to
Laser Notice No. 50, dated (June 24, 2007).
The optical ports of the module need to be terminated with an optical connector or with a dust plug in order to avoid contamination.
1. Overview
SFCxx140GExD is a high-performance transceiver module for Gigabit Ethernet data links over a single mode fibre pair. The
maximum reach1 is 140km, with 38dB end of life (EOL) power budget. The transmitter is a CWDM DFB laser, the receiver an
Avalanche PhotoDiode (APD).
This transceiver module is compliant with the Small Form-factor Pluggable (SFP) Multisource Agreement (MSA) and hot
pluggable. Always contact Skylane Optics commercial agents for compatibility with different equipment platforms.
2. Features
• SFP Multi-Source Agreement compliant (INF-8074)
• Hot pluggable SFP footprint
• Serial ID functionality supported according to (SFF-8472)
• Dual LC connector
• CWDM DFB transmitter (channels 47 to 61)
• APD receiver
• 140km point-to-point transmission on single mode fibre
• Operating temperature range 0°C to 70°C
• Low power dissipation (<1W) Figure 1. SFP Dual Fiber
• Digital diagnostics monitoring (DDM) (non-binding illustration)
3. Applications
• Gigabit Ethernet
• 1´Fiber Channel
4. Optical Interface
Wavelength Optical Output Optical Receiver Receiver Power Budget1

P/N
[nm] Power2 [dBm] Sensitivity3 [dBm] Overload4 [dBm] [dB]
SFCxx140GExD ITU CWDM 2 to 7 ≤ -36 -10 ≥ 38
1. Distance is estimated assuming typical optical losses after decent quality fibre deployment; Only optical budget value is guaranteed
2. EOL, over operating temperature range
3. Measured at 1.25Gbps, PRBS BER 27-1, ER=9dB, BER≤10-12
4. The optical input to the receiver should not exceed this value. Transmitters must never be directly connected to receivers (optical loop back) before ensuring that proper optical
attenuation is used
Specification subject to change without notice 1

Datasheet
5. Technical Parameters
5.1. Recommended Operating Conditions

Parameter Min Typ Max Unit Notes
Storage temperature -40 85 °C
Operating Case Temperature 0 70 °C
Relative Humidity 5 95 % Non condensing
Power Supply Voltage 3.15 3.3 3.45 V
Power Supply Current 300 mA
5.2. Transmitter Optical Specifications

Parameter Min Typ Max Units Notes
Average Output Power 2 7 dBm 5
Centre Wavelength Range 1464.0 1617.5
Wavelength lT -6 lT lT +7.5 nm 6
Spectral Width (-20dB) 1 nm
Extinction Ratio 8.2 dB
5. Output power coupled into a 9/125 µm single mode fibre
6. ITU-T G.694.2 CWDM. For available wavelengths, see section 9
5.3. Receiver Optical Specifications

Parameter Min Typ Max Units Notes
Receiver Sensitivity -36 dBm 7
Receiver Overload -10 dBm 7
Receiver Operating Range 1260 1630 nm
7. Measured at 1.25Gbps, PRBS 27-1, ER=9dB, BER≤10-12
6. Transceiver Electrical Pad Layout
VeeT 20
1 VeeT TD- 19
2 TXFault TD+ 18
3 TX Disable VeeT 17
4 MOD-DEF (2) VccT 16
Towards BEZEL ← 5 MOD-DEF(1) VccR 15 → Towards ASIC
6 MOD-DEF(0) VeeR 14
7 Rate Select RD+ 13
8 LOS RD- 12
9 VeeR VeeR 11
10 VeeR
Figure 2. Transceiver Electrical Pad Layout

Datasheet
7. Module Electrical Pin Definition
SFP MSA (INF-8074i)
Pin Number Name Function

1 VeeT Transmitter Ground
2 TX Fault Transmitter Fault Indication
3 TX_ Disable Transmitter Disable
4 MOD-DEF2 2-Wire Serial Interface Data
5 MOD-DEF1 2-Wire Serial Interface Clock
6 MOD-DEF0 Grounded in Module
7 Rate Select Not Used
8 LOS Loss of Signal
9 VeeR Receiver Ground
12 RD- Inverted Received Data Out
13 RD+ Received Data Out
15 VccR Receiver Power
16 VccT Transmitter Power
18 TD+ Transmit Data In
19 TD- Inverted Transmit Data In
8. EEPROM
SFP MSA [INF-8074]
2 wire address 1010000x 2 wire address 1010001x
0 0
Alarm and Warning
Serial ID Defined by Thresholds (56 bytes)
55
SFP MSA (96 bytes)
Cal Constants
(40 bytes)
95 95
Real Time Diagnostic
Vendor Specifics Interface (24 bytes)
(32 bytes)
119
Vendor Specifics (8 bytes)
127 127
User writable Eeprom
Reserved (120 bytes)
(128 bytes)
247
255 Vendor Specifics (8 bytes)
255
A0h A2h
Figure 3. EEPROM of a an SFP

Datasheet
9. Ordering Information
Part Number Description

SFC47140GE0D SFP dual fibre CWDM, Tx 1470nm (CWDM DFB), Rx (APD), maximum distance 140km,
power budget 38dB, Gigabit Ethernet, LC connector, 0°C to 70°C, DDM
10. Document Revision Information
Revision Description
A Initial release
Skylane Optics® supplies a broad range of optical

transceivers. Our engineers work closely with our
customers to find the best solutions for every application.
We are committed to provide high quality products and Beyond
services to our customers. Quality
For questions on this product please contact:

support@skylaneoptics.com
Reliable
Alliance
Performing
Smartly

Sfcxx140Gexd - SFP Dual Fibre CWDM: CWDM / 140Km / Gigabit Ethernet

Uploaded by

Copyright:

Available Formats

Sfcxx140Gexd - SFP Dual Fibre CWDM: CWDM / 140Km / Gigabit Ethernet

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sfcxx140Gexd - SFP Dual Fibre CWDM: CWDM / 140Km / Gigabit Ethernet

Uploaded by

Copyright:

Available Formats

Datasheet

SFCxx140GExD – SFP Dual Fibre CWDM

Wavelength Optical Output Optical Receiver Receiver Power Budget1

Specification subject to change without notice 1

5.1. Recommended Operating Conditions

5.2. Transmitter Optical Specifications

5.3. Receiver Optical Specifications

6. Transceiver Electrical Pad Layout

Figure 2. Transceiver Electrical Pad Layout

Specification subject to change without notice 2

7. Module Electrical Pin Definition

SFP MSA (INF-8074i)

Pin Number Name Function

SFP MSA [INF-8074]

2 wire address 1010000x 2 wire address 1010001x

Figure 3. EEPROM of a an SFP

Specification subject to change without notice 3

Part Number Description

10. Document Revision Information

Skylane Optics® supplies a broad range of optical

For questions on this product please contact:

Specification subject to change without notice 4

You might also like