CN-6000 series Isolated Converter

Isolated converter CN-6000 series are able to make a variety of selections by users and set with self-diagnosis
and special function using a high accuracy A/D converter and micro-process.

Features
• Clearer display by adopting 3-color LED
• Multi input (TC/RTD/mV/mA)
• Excellent display by adoption of negative LCD
(Selection of 3 different colors)
• Indicating output scale by bar graph
• Indicating the type of input signal and unit conversion
• A wide variety of output type (Current, Voltage, Alarm)
• Isolated independent AO(Analog output) for channel 1&2
(0~10V, 0~20mA)
• Input and output scale setting function
• Input offset and slope compensation function
• Peak hold function
• Internal sensor power supply (24VDC)

Ordering Codes

CN 6 1 0 0 C1
C1 Current 1EA Specifications
C2 Current 2EA
Transmission V1 Voltage 1EA
output Model CN-6100 Series
V2 Voltage 2EA
R1 Alarm 1EA Power supply 85 ~ 264VAC 47 ~ 63Hz
R2 Alarm 2EA Power consumption Approx. 8VA (264VAC 60Hz)
R4 Alarm 4EA 12 Segment, 4 low LCD display (Conversion of RED, GREEN, YELLOW colors)
Power (Voltage) Display
0 85~264VAC 47~63䷍ Graphic bar & Input / Unit display (RED)
Input
10 Universal input Character size W:6.4mm×H:11.0mm(12 Segment) / W:1.4mm×H:2.75mm(Unit)
Item
CN-6 Isolated Converter Current 0 ~ 20mA (Controlling the range of output), Load resistance Max.600Ω
Voltage 0 ~ 10VDC (Controlling the range of output), Load resistance Min.10KΩ
Out
put 1 point : Relay contacting point capacity 250VAC 1A 1a
Connections Alarm 2 point : Relay contacting point capacity 250VAC 3A 1a
4 point : Relay contacting point capacity 250VAC 1A 1a
±0.2% F䳜S ±1Digit(25±5?), ±0.3% F䳜S ±1Digit(-10~20 ºC, 30~50 ºC)
䮝 8Pin Indicating
# SENSOR ୔ But, Under - 100 ºC in TC, ±0.4% F.S ±1Digit
ANALOG TC RTD A+
ISOLATION # 4- 20mA 0- 10VDC ALARM accuracy
. . . 3 1 . . . ୔TC-T, TC-U are at Min.±2.0 ºC
0 OUTPUT
pD#

Amp#
pY

E0 CIRCUIT pD #Y
Setting method Set by Key
transmitter#

0 0 0
䮝 0# 0 0
4 2
2-wire

0
E䮌
5 7 Input sampling cycle 100ms (Analog input), 250ms (Temperature input)
0
POWER# Power supply
FLRCUIT# 
85~264VAC 47~63Hz
. .57Y
6 8 Alarm,Peak-hold,Digital input(Front key),Lock,Input special unit,
Input scale,User compensation,Display scale,Output range,Input scale,
୔ When using 2-wire transmitter, Function
terminal 4, 5 will be SHORT. Input & Output upper/lower expansion, Digital filter,
ISOLATION 4- 20mA 0- 10VDC ALARM1 Changing color for display / switching,Burn out
. . ALARM1
䮝 11Pin 1
VHQVRU
OUTPUT1
CIRCUIT pD #Y ALARM2 Internal voltage 2000VAC 50/60Hz during a minute (Between input terminal and power terminal)
DQDORJ WF UWG D. 2 0 0#

0 . . . 5 Internal vibration 0.75mm Amplitude at frequency of 5~55Hz in each of X,Y,Z directions for 2 hours
Amp 9
pD
pY

NC ALARM3
E0
wudqvplwwhu

䮝 0 0 0 6 ISOLATION . .
ALARM2
Isolation resistance Over 100MΩ (500VDC Mega STD.)
50zluh

0
E䮌 OUTPUT2
10 ALARM4
pD #Y
0
4 CIRCUIT 0# 0 Internal noise ±2KV the square wave noise (pulse width : 1䶺) by the noise simulator
.57Y
11
. 3
POWER
7 Power supply
Memory retention About 10 years (when using non-volatile memory semiconductor)
CIRCUIT 
䮝#Zkhq#xvlqj#50zluh#wudqvplwwhu/ 85~264VAC 47~63Hz Using ambient
####whuplqdo#9/#7#zloo#eh#VKRUW1 8 temperature -10 ºC ~ 50 ºC (at non-freezing status)
Storage temperature -20 ºC ~ 60 ºC (at non-freezing status)
Using ambient
humidity 35 ~ 85% RH
Weight Approx. 200g (except for packing box)

Dimensions, Panel Cutout (Unit : mm)

8 8
DIN35 RAIL

DIN35 RAIL
35.2

:9
80
85

76

40
2-Φ2.25

2-Φ2.25

50 80 20 3.3 40 40 51 more
100 50 50
(8PIN) (11PIN)

D-1
CN-6000 series Isolated Converter
A

Recorders
Functions In message, PV and mA output value is : PV (output value) =
ͺΟΡΦΥ͑ΧΒΝΦΖ 61333nj2fp京

• Unit conversion function(Program mode : UNIT) In message, PV and mA output value is : PV (output value) = 51333nj2fp京 B
ͺΟΡΦΥ͑ΧΒΝΦΖ
In case of temperature input, it can be set to ºF or ºC. When it changes 41333nj2fp京
Data
Unit, all Prescale, Alarm, Output scale, etc. are initialized. Therefore, ·Two unit function 7pD Loggers
- If ductile pressure is lower than air pressure(0), this is indicating the Lqsxw
ppKj
user needs to reset it in accord with the purpose. degree of vibration of mmHg, but if ductile pressure is same or higher 0:93ppKj
than air pressure, this is indication the static pressure of kg/䶫 unit. C
* Formula : ºF = 1.8 ºC + 32
• Digital input function(Program mode : DI-K) • Alarm function (AL-1, AL-2, AL-3, AL-4)
Indicators
It is able to operated through input terminal as below 3 kinds of function. - This indicator has 4 alarm(2 alarm) and can set alarm operation
separately. D
Mode Operation
- If it does not have alarm output, it does not have alarm function.
Alam ON/OFF Although alarm is off, when setting Alarm ON/OFF funtion, alarm
function AlRE is unable to off. Then, using funtion by compulsive alarm off. - Alarm operation is operating through mixing‘alarm type’and‘alarm Converters

Hold indicated Temporarily indicated value is stopped in order to confirm option’

value function HOLD indicated value, in flexible input - Alarm type and option can set on program mode and alarm value E
Zero adjustment “୙ Same as Input compensation funtion.”When zero adjustment, (AL-1, AL-2, AL-3, AL-4) can set on monitoring mode.
function ZERO compensation value is possible to confirm and change in 1N-C Controllers
- How to check parameter
• Input compensation function(Program mode : IN-B) AT!A
Alarm option F
It has not any errors by itself but, if temperature input, analog input etc. A:Normal alarm B:keeping alarm C:Expectation alarm
occur regular error, this function can add and subtract compensation value D:keeping alarm + Expectation alarm Thyristor
Units
for measurement value. Only in case of InSF= TUF, IN-B is operated Alarm type
0:Not use alarm function 1:Upper limit alarm 2:Lower limit alarm G
with atmospheric pressure input value instead of input compensation
SBA:Disconnected sensor alarm
function. (Refer to “● TUF function”)
ྙ Alarm type Transmitters
Ex) In case sensor temperature is 4 ºC and actual temperature is 0 ºC,
PV indicates 0 ºC if setting IN-B= - 4. Alarm type Explanation for alarm operation
H
• Expansion and control the upper/lower limit deviation of input Not use - Eventhough it has alarm output inside and set to‘Not use alarm output’
and transmission output function(Program mode : ExIO ExIO) alarm output
, alarm output is not operated
Temp.
- ‘Not use alarm output’ has not alarm option Sensors
This function is to adjust the range of analog input/output. Please
use after setting in accord with environment, because it can be Upper limit RII K RQ
PV ≥ 800 ºC Alarm output ON I
;33䮎
Upper limit alarm value is set on AL-1, AL-2, AL-3,
changed with input/output to the point you want, if set as below. alarm SY
AL-4 of monitoring mode. Thermo
Following a diagram is the output range of 4-20mA Meters
PV ≤ 200 ºC Alarm output ON
Mode Operation Lower limit RQ K RII
Lower limit alarm value is set on AL-1, AL-2, AL-3, J
533䮎
alarm SY AL-4 of monitoring mode.
Output 4-20mA in only the output range of 4-20mA
Pressure
Output 3.2-20.8mA to the input range which is out of 5% of - In case disconnecting sensor and alarm output is ON, output is stable continuously. Gauges
Disconnected - ‘Disconnected sensor alarm’does not have alarm option.
4-20mA output range sensor alarm ୔ Keeping alarm can be removed by using‘Digital Input function’or power off K
Output 2.4-21.6mA to the input range which is out of 10% of
4-20mA output range ྚ#Alarm option Others

• Indicating scale function (Program mode : H-SC, L-SC)

Alarm option Explanation for alarm operation
Regarding voltage and current input, this function voluntarily sets upper
/ lower limit indicating scale. - If it reaches alarm temperature, alarm output is ON but,
Normal alarm
if it is out of range, output is OFF
As below diagragm, if analog input is a, b and voluntary indicating value
- If it reaches alarm temperature, alarm output is ON and condition is
is A, B for a, b input, a->A, b->B are indicated. stable continuously. (Alarm output HOLD)
keeping alarm
୔ Keeping alarm can be removed by using‘Digital Input function’or power off.
Display Display Display - If it reaches alarm temperature at first time, alarm output is not ON but,
E D Expectation since second time, if it reaches alarm temperature, normal alarm is
D E alarm operating.
d E
CN-6000
Input Input Input keeping alarm+ - keeping alarm and expectation alarm are operating
d###e D e d###e series
Expectation alarm at once.

• Indicating front alarm lamp function • Save peak value function PS

When alarm is operated for relevant channel, as this function is to indicate This function is to check when the abnormal condition of system for
the condition through alarm lamp, it is easily visible about the alarm input, saving Max. value and Min.Value. It is possible to check by
condition by bar graph of relevant channel is flickering or lighting. entering the first setting group on RUN mode.
• Input special function (Program mode : IN.SF) When Max.value and Min.value are out of the range of pressure,
This function is used for when input value and PV are through calculation indicating HHHH, LLLL
of Square, Root( 䮳#) or TUF in case of voltage, current input. It can be initialized by using , key, when display Max. Peak
value( hPEK)or Min. Peak value( lPEK)
Message LIN ROOT SQAR TUF
then peak value is initialized to current input value.
Input value without
Function
any operation
Input value with Input value with x2 • Error indicating function
This has error monitoring function inside. If it occurs error as below
Display \@D[.E Display Display 5
\@D+[,#.E diagram, please check input or setting condition and should take
\@D+##[#,.E Refer to
+[ 䰿3,
Graph
+[ 䮈3,
\@3##+[ 䰽3, Input Two unit action correctly.
Input Input
5
\@0D+[,#.E function Display Description Action
+[ 䰽3,
LLLL When measured sensor input is lower than indicating Input should be within indicatingrange.
HHHH When measured sensor input is higher than indicating "
Appli General Measurement When differential output When temperature sensor is disconnected Check the condition of temperature sensor.
Measure fiow with
cation Input requiring linearization Orifice is from flow signal If there is error under operation. After checking the setting condition, reset.
If input setting and position of switch isinconsistent
(but, temperature sensor and analog input are classified) After checking input specification, reset.

D-2
 CN-6000 series Isolated Converter

Program mode : INIT)

• Initializing parameter function (Program
After pressing MODE key + key for 3 sec simultaneously and Front Panel Identifications
indicating [ INIT] on display, if press MODE key by using or
key when it indicates [ YES], it process initializing.
(୔Parameter initialization is possible only when [ LOCK] function is OFF.)
丿 S K JBER TDCA CWk HzmVA %°
乀 丿 S K JBER TDCA CWk HzmVA %°
乀
• Transmission output scale function( hOUT, lOUT), Transmission 举
output range function( hOR?, lOR?) 乁 乂
This function is to set output for indicating value on analog output.
When indicating hOUT, it outputs analog output value setting to
that output 1 is hOR1 / output 2 is hOR2 and when indicating lOUT, 乃 乄 乃 乄
it outputs analog output value setting to lOR9.1/20
୔OUTPUT ACCURACY = OUTPUT SCALE / FULL SCALE
Output Output 举 Indicating display : When operating, it displays present value / When setting
hOR hOR parameter, it displays parameter and set value.
lOR lOR 丿 Input specification display : Input type at IN-P parameter is flickering.
Input Input (If selecting TC sensor, TC-L, TC-N, TC-U,TC-P, it displays at the right side)
hOUT lOUT lOUT hOUT
乀 Indicating unit
乁 Output scale BAR : In case of analog output, output displays to % by scale
• Digital filtering function (Program mode :
BAR.
AvF, MAvF- User lever : HIGH)
乂 Alarm output lamp : When alarm output, the alarm lamp is flickering.
Normal average filter [ AvF] is the indicating type by averaging the N
乃 MODE key : It is used for when entering to setting mode or when moving
cycle of sampling value. Moving average filter [ MAvF] indicates in real-
between parameters.
time by averaging the previous N cycle of sampling value.
乄 Moving key, UP / DOWN key : It is used for that setting parameter.
୔Setting range : 01~32 (If setting 01, it does not operate digital filtering function)

• Display color changing and switching function

(Program mode : COLR)
Input Range for the Sensors
This function is to select the color of front display among red, green, yellow.
Parameter Explanation Using(display) Using(display)
Sensor Type Display
temp. range ºC temp. range ºF
Display color is RED.
K(CA) TcK1 -200 ~ 1350 -328 ~ 2462
Display color is GREEN (Factory defaults).
K(CA) TcK2 -199.9 ~ 999.9 -328 ~ 1832
Display color is YELLOW. J(IC) TC-J -199.9 ~ 800.0 -328 ~ 1472
When EVENT? is operated, display color is to GREEN from RED. E(CR) TC-E -199.9 ~ 800.0 -328 ~ 1472
T(CC) TC-T -199.9 ~ 400.0 -199.9 ~ 752.0
When EVENT? is operated, display color is to RED from GREEN.
Thermo B(PR) TC-B 400 ~ 1800 752 ~ 3272
୔ EVENT : When alarm is on and when it indicates HHHH, LLLL, , . couple
R(PR) TC-R 0 ~ 1750 32 ~ 3182
S(PR) TC-S 0 ~ 1750 32 ~ 3182
• Burn out function (Program mode : ) N(NN) -200 ~ 1300 -328 ~ 2372
TC-N
When TC temperature sensor is disconnected, this function is C(W5) 0 ~ 2300 32 ~ 4172
TC-C
transmitting the abnormal accident and outputting the value of HHHH L(IC) -199.9 ~ 900.0 -328 ~ 1652
TC-L
or LLLL condition according to the setting and display is flickering U(CC) -199.9 ~ 400.0 -199.9 ~ 752.0
TC-U
[ ] message. Platinel II 0 ~ 1390 32 ~ 2534
TC-P
- If setting BURN=ON, it outputs 20mA/10V/HIGH-ALARM. CU50Ω -199.9 ~ 200.0 -199.9 ~392.0
Cu50
- If setting BURN=OFF, it outputs 4mA/0V/LOW-ALARM. CU100Ω -199.9 ~ 200.0 -199.9 ~392.0
Cu10
(୔ When analog output, the setting maximum / minimum value outputs RTD JPt100Ω -199.9 ~ 600.0 -328 ~ 1112
JPt1
to input/output expansion function) DPt50Ω -199.9 ~ 600.0 -328~ 1112
DPt5
• Lock mode (Program mode : LOCK)
* DPt100Ω DPt1 -199.9 ~ 850.0 -328 ~ 1530

This function is to check setting value of parameter and to restrict changes. Cur- 0.00 ~ 20.00mA aMA1
rent 4.00 ~ 20.00mA
aMA2
OFF LOC1 LOC2 -50.0 ~ 50.0mV
Ana- aMV1 Scale display range : -1999 ~ 9999
First setting group log Volt- -199.9~ 200.0mV aMV2
Second setting group age
-1.000 ~ 1.000V A-V1
Check/setting possible -1.00 ~ 10.00V A-V2
Check possible/setting impossible
Check impossible · If applying an electric current with pressing M key simultaneously, the type of
input is able to be expanded.
୔ If lock mode is set to LOC2 and enter into program mode, it is only indicating
LOCK parameter.

D-3