NF EN 1011-1-A2-English

FE136093 ISSN 0335-3931
European standard NF EN 1011-1/A2

July 2004
French standard Classification index: A 89-101-1/A2
ICS: 25.160.10
Welding
Recommendations for welding
of metallic materials
Part 1: General guidance for arc welding
F : Soudage — Recommandations pour le soudage des matériaux métalliques —

Partie 1 : Lignes directrices générales pour le soudage à l'arc
D : Schweißen — Empfehlungen zum Schweißen metallischer Werkstoffe —
Teil 1: Allgemeine Anleitungen für das Lichtbogenschweißen
© AFNOR 2004 — All rights reserved
Amendment A2
to the approved standard NF EN 1011-1, dated August 1998, approved by
decision of the Director General of AFNOR on June 30, 2004 taking effect on
July 30, 2004.
Correspondence The amendment A2:2003 to the European standard EN 1011-1:1998 has the status
of French standard.
Analysis This document specifies the general guidance for fusion welding of metallic materials
in all delivery conditions.
Descriptors Technical International Thesaurus: arc welding, manual metal arc welding, low
alloy steels, ferritic steels, butt welds, fillet welds, edge preparation, quality,
specifications.
Modifications
Corrections
Published and distributed by Association Française de Normalisation (AFNOR — French standard institute) — 11, avenue Francis de Pressensé —
93571 Saint-Denis La Plaine Cedex — Tel.: + 33 (0)1 41 62 80 00 — Fax: + 33 (0)1 49 17 90 00 — www.afnor.fr
© AFNOR 2004 AFNOR 2004 1st issue 2004-07-P

EUROPEAN STANDARD EN 1011-1:1998/A2
NORME EUROPÉENNE
EUROPÄISCHE NORM December 2003
ICS 25.160.10
English version
Welding - Recommendations for welding of metallic materials -

Part 1: General guidance for arc welding
Soudage - Recommandations pour le soudage des Schweißen - Empfehlungen zum Schweißen metallischer
matériaux métalliques - Partie 1: Lignes directrices Werkstoffe - Teil 1: Allgemeine Anleitungen für das
générales pur le soudage à l'arc Lichtbogenschweißen
This amendment A2 modifies the European Standard EN 1011-1:1998; it was approved by CEN on 20 November 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1011-1:1998/A2:2003: E
worldwide for CEN national Members.
EN 1011-1:1998/A2:2003 (E)
Contents Page
Foreword............................................................................................................................................................. 3
1 Modifications to foreword .................................................................................................................... 4
2 Delete Annex ZA (informative)............................................................................................................. 4
2
EN 1011-1:1998/A2:2003 (E)
Foreword
This document EN 1011-1:1998/A2:2003 has been prepared by Technical Committee CEN/TC 121 “Welding”,
the secretariat of which is held by DS.
This Amendment to the European Standard EN 1011-1:1998 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by June 2004, and conflicting national
standards shall be withdrawn at the latest by June 2004.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands,
Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
3
EN 1011-1:1998/A2:2003 (E)
1 Modifications to foreword
Replace third paragraph by the following: "This document has been prepared under a mandate given to CEN
by the European Commission and the European Free Trade Association".
2 Delete Annex ZA (informative)

Delete informative Annex ZA addressing EU Directive 97/23/EC.

NF EN 1011-1-A2-English

Uploaded by

Copyright:

Available Formats

NF EN 1011-1-A2-English

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

NF EN 1011-1-A2-English

Uploaded by

Copyright:

Available Formats

FE136093 ISSN 0335-3931

European standard NF EN 1011-1/A2

French standard Classification index: A 89-101-1/A2

F : Soudage — Recommandations pour le soudage des matériaux métalliques —

© AFNOR 2004 AFNOR 2004 1st issue 2004-07-P

Welding - Recommendations for welding of metallic materials -

EUROPEAN COMMITTEE FOR STANDARDIZATION

Management Centre: rue de Stassart, 36 B-1050 Brussels

2 Delete Annex ZA (informative)

You might also like