3159-QFP64E: SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
3159-QFP64E: SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
3159-QFP64E: SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
Monolithic Linear IC
LA9241M
Analog Signal Processor (ASP)
for CD players
Functions
I/V amplifier, RF amplifier (with AGC), SLC, APC, FE, TE
(with VCA and auto-balance function), focus servo amplifier
(with offset cancellation function), tracking servo amplifier
(with offset cancellation function), spindle servo amplifier
(with gain switching function), sled servo amplifier (with off
function), focus detection (DRF, FZD), track detection (HFL,
TES), defect detection, and shock detection.
Specifications
Maximum Ratings at Ta = 25°C, Pins 22, 45 = GND
Operating Characteristics at Ta = 25°C, Pins 22, 45 = GND, VCC (pins 56, 64) = 5 V
No.5564 - 2/21
LA9241M
No.5564 - 3/21
LA9241M
Pin Functions
Pin
Symbol Contents
No.
1 FIN2 Pickup photodiode connection pin. Added to FIN1 pin to generate the RF signal, subtracted from FIN1 pin to generate
the FE signal.
2 FIN1 Pickup photodiode connection pin.
3 E Pickup photodiode connection pin. Subtracted from F pin to generate the TE signal.
4 F Pickup photodiode connection pin.
5 TB TE signal DC component input pin.
6 TE− Pin which connects the TE signal gain setting resistor between this pin and TE pin.
7 TE TE signal output pin.
8 TESI TES (Track Error Sense) comparator input pin. The TE signal is input through a bandpass filter.
9 SCI Shock detection input pin.
10 TH Tracking gain time constant setting pin.
11 TA TA amplifier output pin.
12 TD− Pin for configuring the tracking phase compensation constant between the TD and VR pins.
13 TD Tracking phase compensation setting pin.
14 JP Tracking jump signal (kick pulse) amplitude setting pin.
15 TO Tracking control signal output pin.
16 FD Focusing control signal output pin.
17 FD− Pin for configuring the focusing phase compensation constant between the FD and FA pins.
18 FA Pin for configuring the focusing phase compensation constant between the FD− and FA− pins.
19 FA− Pin for configuring the focusing phase compensation constant between the FA and FE pins.
20 FE FE signal output pin.
21 FE− Pin which connects the FE signal gain setting resistor between this pin and FE pin.
22 AGND Analog signal GND.
23 NC No connection
24 SP CV+ and CV− pins input signal single-end output.
25 SPG 12-cm spindle mode gain setting resistor connection pin.
26 SP− Spindle phase compensation constant connection pin, along with the SPD pin.
27 SPD Spindle control signal output pin.
28 SLEQ Sled phase compensation constant connection pin.
29 SLD Sled control signal output pin.
30 SL− Input pin for sled movement signal from microprocessor.
31 SL+ Input pin for sled movement signal from microprocessor.
32 JP− Input pin for tracking jump signal from DSP.
33 JP+ Input pin for tracking jump signal from DSP.
34 TGL Input pin for tracking gain control signal from DSP. Gain is low when TGL is high.
35 TOFF Input pin for tracking off control signal from DSP. Tracking servo is off when TOFF is high.
36 TES Output pin for TES signal to DSP.
37 HFL The High Frequency Level is used to determine whether the main beam is positioned over a bit or over the mirrored
surface.
38 SLOF Sled servo off control input pin
39 CV− Input pin for CLV error signal from DSP.
40 CV+ Input pin for CLV error signal from DSP.
41 RFSM RF output pin.
42 RFS− RF gain setting and EFM signal 3T compensation constant setting pin, along with the RFSM pin.
43 SLC Slice Level Control is an output pin that controls the data slice level used by the DSP for the RF waveform.
44 SLI Input pin used by DSP for controlling the data slice level.
45 DGND Digital system GND pin.
46 FSC Focus search smoothing capacitor output pin.
47 TBC Tracking Balance Control; EF balance adjustment variable range setting pin
48 NC No connection
49 DEF Disc defect detection output pin.
50 CLK Reference clock input pin. 4.23 MHz signal from the DSP is input.
51 CL Microprocessor command clock input pin.
No.5564 - 4/21
LA9241M
Pin
Symbol Contents
No.
52 DAT Microprocessor command data input pin.
53 CE Microprocessor command chip enable input pin.
54 DRF RF level detection output (Detect RF).
55 FSS Focus Search Select; focus search mode (± search/+search vs. the reference voltage) switching pin
56 VCC2 Servo system and digital system VCC pin.
57 REFI By-pass capacitor connection pin for reference voltage.
58 VR Reference voltage output pin.
59 LF2 Disc defect detection time constant setting pin.
60 PH1 RF signal peak hold capacitor connection pin.
61 BH1 RF signal bottom hold capacitor connection pin.
62 LDD APC circuit output pin.
63 LDS APC circuit input pin.
64 VCC1 RF system VCC pin.
No.5564 - 5/21
LA9241M
Microcontroller
INTERFACE
No.5564 - 6/21
LA9241M
Test Circuit
No.5564 - 7/21
LA9241M
Description of Operation
1. APC (auto laser power control)
This circuit controls the pickup laser power. The laser is turned on and off by commands from the microprocessor.
6. Sled servo
The response characteristics are set by SLEQ (pin 28). The amplifier positioned after SLEQ (pin 28) has a mute function that
is applied either when SLOF (pin 38) goes high or the SLED OFF command is issued. The sled is moved by inputting
current to SL− (pin 30) and SL+ (pin 31); specifically, the pins are connected to the microprocessor output ports via resistors,
and the movement gain is set by the resistance value of that resistor. It is important to note that if there is a deviation in the
resistance values for SL− (pin 30) and SL+ (pin 31), an offset will arise in the SLD output.
7. Spindle servo
This configures the servo circuit, which maintains the linear velocity of the disc at a constant speed, along with the DSP. This
circuit accepts signals from the DSP through CV− (pin 39) and CV+ (pin 40) and sets the equalizer characteristics through SP
(pin 24), SP− (pin 26), and SPD (pin 27), which are output to SPD (pin 27). The 12-cm mode amplifier gain is set by the
resistor connected between SPG (pin 25) and the reference voltage. In 8-cm mode, this amplifier serves as an internal buffer,
and SPG (pin 25) is ignored. Note that the gain setting is made for 8-cm mode first, and then 12-cm mode. If SPG (pin 25)
is left open, the gain is forcibly set for 8-cm mode, regardless of whether 8-cm or 12-cm mode is in effect.
No.5564 - 8/21
LA9241M
Pickup position
Focus
Focus
No.5564 - 9/21
LA9241M
11. DEFECT
The mirrored surface level is maintained by the capacitor for LF2 (pin 59); when a drop in the EFM signal (RFSM output)
reaches 0.35 V or more, a high signal is output to DEF (pin 49). If DEF (pin 49) goes high, the tracking servo enters THLD
mode. In order to prevent the tracking servo from entering THLD mode when a defect is detected, prevent DEFECT from
being output by either shorting DEF (pin 49) to GND, or shorting LF2 (pin 59) to GND. The DEFECT output is driven by
constant current (approximately 100 µA).
EFM signal
(RFSM output)
Timing
No.5564 - 10/21
LA9241M
1 µs or more
1 µs or more
When sending a TRACK-OFFSET ADJUST START command or a FOCUS-OFFSET ADJUST START command after either
VCC ON (POWER ON RESET), RESET command, or a corresponding OFFSET ADJUST OFF command, waiting time is
necessary as listed below. (Only when a 4.2 MHz clock is input.)
TRACK-OFFSET ADJUST START: 4 ms or more
FOCUS-OFFSET ADJUST START: 4 ms or more
No.5564 - 11/21
LA9241M
1 FIN2
2 FIN1
3 E
4 F
5 TB
6 TE–
17 FD−
21 FE−
26 SP−
28 SLEQ
44 SLI
16 FD
27 SPD
43 SLC
8 TESI
36 TES
No.5564 - 12/21
LA9241M
9 SCI
34 TGL
7 TE
10 TH
11 TA
12 TD−
13 TD
No.5564 - 13/21
LA9241M
14 JP
15 TO
18 FA
19 FA−
20 FE
No.5564 - 14/21
LA9241M
25 SPG
29 SLD
30 SL−
31 SL+
32 JP−
33 JP+
35 TOFF
No.5564 - 15/21
LA9241M
37 HFL
46 FSC
49 DEF
54 DRF
38 SLOF
39 CV−
40 CV+
24 SP
42 RFS−
47 TBC
No.5564 - 16/21
LA9241M
50 CLK
51 CL
52 DAT
53 CE
55 FSS
57 REFI
58 VR
59 LF2
No.5564 - 17/21
LA9241M
41 RFSM
60 PH1
61 BH1
62 LDD
63 LDS
No.5564 - 18/21
LA9241M
No.5564 - 19/21
Type LA9220M LA9230M LA9231M LA9233M LA9240M LA9241M
Package QFP-64E QFP-64E QFP-64E QFP-64E QFP-64E QFP-64E
Allowable operating supply voltage
VCCop max 5.5 V 5.5 V 5.5 V 5.5 V 5.5 V 5.5 V
VCCop min1 3.6 V : t = –25 to +75°C 3.6 V : t = –25 to +75°C 3.6 V : t = –25 to +75°C 3.6 V : t = –25 to +75°C 3.6 V : t = –25 to +75°C 3.2 V : t = –25 to +75°C
VCCop min2 3.4 V : t = –5 to +75°C 3.0 V : t = –10 to +75°C
Current drain (When VCC = 5 V) 40 mA 32 mA 32 mA 32 mA 32 mA 32 mA
VCO circuit built in Yes No No No No No
Auto adjustment function
. Focus offset adjsutment Adjustment position: FD Adjustment position: FD Adjustment position: FD Adjustment position: FD Adjustment position: FE Adjustment position: FE
Maximum adjsutment time 270 ms 270 ms 270 ms 270 ms 30 ms 30 ms
Tracking offset adjustment Adjustment position: TO Adjustment position: TO Adjustment position: TO Adjustment position: TO Adjustment position: TE Adjustment position: TE
Maximum adjustment time 30 ms 30 ms 30 ms 30 ms 30 ms 30 ms
. E/F balance auto adjustment Yes Yes Yes Yes Yes Yes
. RF level AGC function Yes Yes Yes Yes Yes Yes
RF waveform amplitude when 1.8 Vp-p 1.8 Vp-p 1.8 Vp-p 1.8 Vp-p 1.8 Vp-p 1.5 Vp-p
Function Comparisons for CD-ASP
VCC = 5 V
RF waveform amplitude when 1.3 Vp-p 1.3 Vp-p 1.3 Vp-p 1.3 Vp-p 1.2 Vp-p : VCC = 3.4 V 0.9 Vp-p : VCC = 3.0 V
VCC min
. Tracking servo gain RF level Yes Yes Yes Yes Yes Yes
following function
Focus search time Approx. 280 msec Approx. 280 msec Approx. 1.1 sec Approx. 1.1 sec Approx. 560 msec Approx. 560 msec
Regeneration speed ×2 ×2 ×2 ×4 ×4 ×4
Track-kick signal output Built in Built in No output No output No output No output
(Track-kick during E/F balance
LA9241M
adjsutment)
Focus search smoothing capacitor No No Yes Yes Yes Yes
pin: FSC
E/F balance variable range setting No No No No Yes Yes
pin: TBC
Focus search mode switch pin: FSS No No No No Yes Yes
Vth for HFL detection 2.3 V 2.3 V 2.3 V 2.3 V 2.1 V 2.1 V
DRF current capacity Approx.100 µA Approx. 100 µA Approx. 100 µA Approx. 100 µA Approx.250 µA Approx. 250 µA
APC reference voltage 180 mV: typ 180 mV: typ 180 mV: typ 180 mV: typ 180 mV: typ 190 mV: typ
LCD voltage where LDD = 3 V
No connection Pin 46, 47, 48, 55 Pin 47, 48, 55 Pin 47, 48, 55 Pin 48 Pin 23,48
No.5564 - 20/21
LA9241M
No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment,
nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or
indirectly cause injury, death or property loss.
Anyone purchasing any products described or contained herein for an above-mentioned use shall:
1 Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors
and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and
expenses associated with such use:
2 Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO
ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume
production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use
or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of January, 1997. Specifications and information herein are subject to change without notice.
No.5564 - 21/21