Goodrich 2LA456335-33-001 R0 Dt. 19.07.21
Goodrich 2LA456335-33-001 R0 Dt. 19.07.21
Goodrich 2LA456335-33-001 R0 Dt. 19.07.21
1. PLANNING INFORMATION
A. Effectivity
This Vendor Service Bulletin (VSB) is applicable to the following lights:
LED Wing Engine Scan Light LH, P/N 2LA456335-01, AMDT. A
B. Concurrent Requirements
None.
C. Reason
This VSB has been issued to inform the operators about the introduction of a new Capacitor in the
LED Main Board Assy, caused by obsolescence. Due to the new Capacitor, the P/N of the LED
Main Board Assy changes:
D. Description
With the installation of the new LED Main Board Assy, the AMDT of the LED Wing Engine Scan
Light P/N 2LA456335-01 and 2LA456335-02 changes from A to B:
The first LED Wing Engine Scan Light LH, P/N 2LA456335-01 produced with Amendment B has
Serial Number 5180032.
The first LED Wing Engine Scan Light RH, P/N 2LA456335-02 produced with Amendment B has
Serial Number 5178000.
E. Compliance
Optional – Service Bulletin for convenience or option.
F. Approval
The modification procedures described in this SB are reviewed and technically accepted by Airbus
to apply to the Airbus fleet affected.
This SB does not contain any change information that revises the equipment definition covered by
Airbus approved modifications.
G. Manpower
It is assumed that the LED Wing Engine Scan Light is removed from Aircraft.
Testing: 0,5 h
K. References
The sources of information used in preparation of this VSB include Goodrich Lighting Systems
documentation and the following publications:
CMM: 33-49-10
L. Publications Affected
Not applicable.
M. Interchangeability
Two-way interchangeable.
2. MATERIAL INFORMATION
*Unit Price valid until 31.12.2021. Customer specific prices may vary and can be reviewed on our
customer portal.
The new parts can be ordered on our customer portal:
https://customers.collinsaerospace.com/
If you require Goodrich Lighting Systems to inspect, repair or modify your LED Wing Engine Scan
Light in accordance with this VSB, contact:
In case the LED Main Board Assy fails within the standard warranty period acc. to SSC, the
modification will be done free of charge by the above listed MRO. In all other cases, the
modification will be charged to the customer.
The Operator can perform the VSB according to the Accomplishment Instructions in Section 3 of
this VSB.
The parts required for accomplishment of this VSB may be procured separately from Goodrich
Lighting Systems.
Technical Support:
C. List of components
D. Subcomponents to be re-identified
Not applicable.
E. Tooling
None.
F. Special Tools
None.
3. ACCOMPLISHMENT INSTRUCTIONS
A. General
Manuals listed in section 1 of this VSB provide applicable disassembly, cleaning, inspection,
reassembly and testing instructions and shall be referred to during the accomplishment of the
following operations.
B. Preparation
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
C. Procedure
(1) Remove the Countersunk Screws (1-10) to remove the Lens Assy (1-5) from the Housing
Assy (1-42).
(2) Remove the Countersunk Screws (1-25) and Bushings (1-30) to remove the LED Main
Board Assy (1-20 or 1-20A) from the Housing (1-110).
(3) Disconnect the electrical connection between the Plug (1-45) and the Receptacle (1-35A).
(2) Install the LED Main Board Assy (1-20B or 1-20C) with the Countersunk Screws (1-25) and
Bushing (1-30).
(3) Install the Lens Assy (1-5) on the Housing Assy (1-42) with Countersunk Screws (1-10).
Apply a torque value of 7 Ibf-in (0.8 Nm).
D. Re-identification of equipment
Re-identify the LED Wing Engine Scan Light. Update the Amendment status on the label with a
waterproof pen. Refer to the following table for the applicable Amendment status :
E. Test
Test the LED Wing Engine Scan Light in accordance with CMM 33-49-10.
F. Close-up
Not applicable.