WELDING PROCEDURE QUALIFICATION RECORD (WPQR)

(EN / ISO 15614-1:2017)

Welding Procedure Qualification-Test certificate
Manufacturer’s WPQR No: WOPEX_001
Manufacturer’s pWPS No: WOPEX_11-03
Manufacturer’s Record of Test No – R000008_210125-164159
Manufacturer: WOPEX Manufacturing India Pvt Ltd
Address : Plot No. A-21/7-22,
Examiner or Examining body:
Village-Khalumbre (Khed),
Chakan MIDC Phase II Mr. Hugo Mezin (RWC-Level A, IWE)
Code/Testing Standard: EN / ISO 15614-1:2017 Level 2
Date of welding: 29.12.2020
Qualification Details
Details Actual Range of qualification
Welding Process(es) MAG-135 (Partly Mechanized) 135(Partly Mechanized)
Type of joint and weld Butt joint (full penetration) BW (ss nb, ss mb, bs)
Parent metal group(s) and sub- ISO 15608 – G1.2 ISO15608- G1.1, 1.2
group(s)
Parent metal thickness (mm): 4 3 – 5.2
Weld metal thickness (mm): s4 s ≤ 8mm
Single run / Multi run: Single run Single run
Filler material designation: ISO14341-A-G 42 3 M21 3Si1 ISO14341-A-G 42 3 M21 3Si1
(SFA5.18 ER70S-6)
Filler material make: ESAB Any
Filler Material size: Ø 1.0 mm Any
Throat thickness (mm): NA NA
Outside pipe diameter (mm): Ø 48 ≥ 24
Designation of shielding ISO14175- M21 (Ar.80% +Co2_20%) ISO 14175- M21
gas/flux:
Designation of backing gas NA NA
Type of polarity: DCEP DCEP
Transfer mode: Globular Globular, Spray
Heat input (KJ/mm) 0.79 0.59 – 0.99
Welding positions: PC PA, PC
Pre-heat temperature: 25⁰ C min. 22⁰ C
Post heating: NA NA
Inter pass temperature: NA NA
Post weld -heat-treatment: NA NA
Other information: NA NA

We confirm that the statement in this record are correct and that the test piece were prepared, welded, tested and
have fulfilled the requirements in accordance with ISO15614-1.

27/09/2021 Hugo Mezin (RWC, IWE), 27.09.2021

Location Date of Issue Examiner or Examining body
 WELDING PROCEDURE QUALIFICATION RECORD (WPQR)
(EN / ISO 15614-1:2017)
Welding Procedure Qualification-Test certificate
Manufacturer’s WPQR No: WOPEX_002
Manufacturer’s pWPS No: WOPEX_20-01/02
Manufacturer’s Record of Test No – R000008_210519-114709
Manufacturer: WOPEX Manufacturing India Pvt Ltd
Address : Plot No. A-21/7-22,
Examiner or Examining body:
Village-Khalumbre (Khed),
Chakan MIDC Phase II Mr. Hugo Mezin (RWC-Level A, IWE)
Code/Testing Standard: EN / ISO 15614-1:2017 Level 2
Date of welding: 20.03.2021
Qualification Details
Details Actual Range of qualification
Welding Process(es) MAG-135 (Partly Mechanized) 135(Partly Mechanized)
Type of joint and weld Butt joint (full penetration) BW (ss nb, ss mb, bs)
Parent metal group(s) and sub- ISO 15608 – G1.2 ISO15608- G1.1, 1.2
group(s)
Parent metal thickness (mm): 10 3 – 20
Weld metal thickness (mm): s 10 s ≤ 20mm
Single run / Multi run: Multi run Multi run
Filler material designation: ISO14341-A-G 42 3 M21 3Si1 ISO14341-A-G 42 3 M21 3Si1
(SFA5.18 ER70S-6)
Filler material make: ESAB Any
Filler Material size: Ø 1.0 mm Any
Throat thickness (mm): NA NA
Outside pipe diameter (mm): - >500mm or >150mm in PC and PA/PF
rotated
Designation of shielding ISO14175- M21 (Ar.80% +Co2_20%) ISO 14175- M21
gas/flux:
Designation of backing gas NA NA
Type of polarity: DCEP DCEP
Transfer mode: Root: Globular, Capping: Spray Globular, Spray
Heat input (KJ/mm) 0.76/1.12 0.57 – 1.40
Welding positions: PA PA
Pre-heat temperature: 25⁰ C min. 22⁰ C
Post heating: NA NA
Inter pass temperature: 250⁰ C ≤ 300⁰ C
Post weld -heat-treatment: NA NA
Other information: NA NA
We confirm that the statement in this record are correct and that the test piece were prepared, welded, tested and
have fulfilled the requirements in accordance with ISO15614-1.

27/09/2021 Hugo Mezin (RWC, IWE), 27.09.2021

Location Date of Issue Examiner or Examining body
 WELDING PROCEDURE QUALIFICATION RECORD (WPQR)
(EN / ISO 15614-1:2017)
Welding Procedure Qualification-Test certificate
Manufacturer’s WPQR No: WOPEX_003
Manufacturer’s pWPS No: WOPEX_04-02
Manufacturer’s Record of Test No – R000008_210118-122803
Manufacturer: WOPEX Manufacturing India Pvt Ltd
Address : Plot No. A-21/7-22,
Examiner or Examining body:
Village-Khalumbre (Khed),
Chakan MIDC Phase II Mr. Hugo Mezin (RWC-Level A, IWE)
Code/Testing Standard: EN / ISO 15614-1:2017 Level 2
Date of welding: 20.12.2020
Qualification Details
Details Actual Range of qualification
Welding Process(es) MAG-135 (Partly Mechanized) 135(Partly Mechanized)
Type of joint and weld Butt joint (full penetration) BW (ss nb, ss mb, bs)
Parent metal group(s) and sub- ISO 15608 – G1.2 ISO15608- G1.1, 1.2
group(s)
Parent metal thickness (mm): 40 20 – 80
Weld metal thickness (mm): s 40 s ≤ 80 mm
Single run / Multi run: Multi run Multi run
Filler material designation: ISO14341-A-G 42 3 M21 3Si1 ISO14341-A-G 42 3 M21 3Si1
(SFA5.18 ER70S-6)
Filler material make: ESAB Any
Filler Material size: Ø 1.0 mm Any
Throat thickness (mm): NA NA
Outside pipe diameter (mm): - >500mm or >150mm in PC and PA/PF
rotated
Designation of shielding ISO14175- M21 (Ar.80% +Co2_20%) ISO 14175- M21
gas/flux:
Designation of backing gas NA NA
Type of polarity: DCEP DCEP
Transfer mode: Root: Globular, Capping: Spray Globular, Spray
Heat input (KJ/mm) 0.84/1.29 0.59 – 1.61
Welding positions: PA PA
Pre-heat temperature: 25⁰ C min. 75⁰C for thickness ≥ 30mm
Post heating: NA NA
Inter pass temperature: 250⁰ C ≤ 300⁰ C
Post weld -heat-treatment: NA NA
Other information: NA NA
We confirm that the statement in this record are correct and that the test piece were prepared, welded, tested and
have fulfilled the requirements in accordance with ISO15614-1.

27/09/2021 Hugo Mezin (RWC, IWE), 27.09.2021

Location Date of Issue Examiner or Examining body
 WELDING PROCEDURE QUALIFICATION RECORD (WPQR)
(EN / ISO 15614-1:2017)
Welding Procedure Qualification-Test certificate
Manufacturer’s WPQR No: WOPEX_005
Manufacturer’s pWPS No: WOPEX_13-01
Manufacturer’s Record of Test No – R000008_210125-142622
Manufacturer: WOPEX Manufacturing India Pvt Ltd
Address : Plot No. A-21/7-22,
Examiner or Examining body:
Village-Khalumbre (Khed),
Chakan MIDC Phase II Mr. Hugo Mezin (RWC-Level A, IWE)
Code/Testing Standard: EN / ISO 15614-1:2017 Level 2
Date of welding: 02.01.2021
Qualification Details
Details Actual Range of qualification
Welding Process(es) MAG-135 (Partly Mechanized) 135(Partly Mechanized)
Type of joint and weld T joint (Fillet weld) T joint (Fillet weld)
Parent metal group(s) and sub- ISO 15608 – G1.2 ISO15608- G1.1, 1.2
group(s)
Parent metal thickness (mm): P-8 / T-8 3 - 16
Weld metal thickness (mm): NA NA
Single run / Multi run: Multi run Multi run
Filler material designation: ISO14341-A-G 42 3 M21 3Si1 ISO14341-A-G 42 3 M21 3Si1
(SFA5.18 ER70S-6)
Filler material make: ESAB Any
Filler Material size: Ø 1.0 mm Any
Throat thickness (mm): a8 No restriction
Outside pipe diameter (mm): 60 ≥ 30
Designation of shielding ISO14175- M21 (Ar.80% +Co2_20%) ISO 14175- M21
gas/flux:
Designation of backing gas NA NA
Type of polarity: DCEP DCEP
Transfer mode: Globular / Spray Globular, Spray
Heat input (KJ/mm) 0.99/1.39 0.74 – 1.74
Welding positions: PB PA, PB
Pre-heat temperature: 25⁰ C min. 22⁰C
Post heating: NA NA
Inter pass temperature: 250⁰ C ≤ 300⁰ C
Post weld -heat-treatment: NA NA
Other information: NA NA
We confirm that the statement in this record are correct and that the test piece were prepared, welded, tested and
have fulfilled the requirements in accordance with ISO15614-1.

27/09/2021 Hugo Mezin (RWC, IWE), 27.09.2021

Location Date of Issue Examiner or Examining body
 WELDING PROCEDURE QUALIFICATION RECORD (WPQR)
(EN / ISO 15614-1:2017)
Welding Procedure Qualification-Test certificate
Manufacturer’s WPQR No: WOPEX_006
Manufacturer’s pWPS No: WOPEX_03-01
Manufacturer’s Record of Test No – R000008_210118-143113
Manufacturer: WOPEX Manufacturing India Pvt Ltd
Address : Plot No. A-21/7-22,
Examiner or Examining body:
Village-Khalumbre (Khed),
Chakan MIDC Phase II Mr. Hugo Mezin (RWC-Level A, IWE)
Code/Testing Standard: EN / ISO 15614-1:2017 Level 2
Date of welding: 20.12.2020
Qualification Details
Details Actual Range of qualification
Welding Process(es) MAG-135 (Partly Mechanized) 135(Partly Mechanized)
Type of joint and weld T joint (Fillet weld) T joint (Fillet weld)
Parent metal group(s) and sub- ISO 15608 – G1.2 ISO15608- G1.1, 1.2
group(s)
Parent metal thickness (mm): 30 / 30 ≥5
Weld metal thickness (mm): NA NA
Single run / Multi run: Multi run Multi run
Filler material designation: ISO14341-A-G 42 3 M21 3Si1 ISO14341-A-G 42 3 M21 3Si1
(SFA5.18 ER70S-6)
Filler material make: ESAB Any
Filler Material size: Ø 1.0 mm Any
Throat thickness (mm): a12 No restriction
Outside pipe diameter (mm): - >500mm or >150mm in PC and PA/PF
rotated
Designation of shielding ISO14175- M21 (Ar.80% +Co2_20%) ISO 14175- M21
gas/flux:
Designation of backing gas NA NA
Type of polarity: DCEP DCEP
Transfer mode: Globular / Spray Globular, Spray
Heat input (KJ/mm) 0.97/1.37 0.73 – 1.71
Welding positions: PB PA, PB
Pre-heat temperature: 25⁰ C min. 75⁰C for thickness ≥ 25mm
Post heating: NA NA
Inter pass temperature: 250⁰ C ≤ 300⁰ C
Post weld -heat-treatment: NA NA
Other information: NA NA
We confirm that the statement in this record are correct and that the test piece were prepared, welded, tested and
have fulfilled the requirements in accordance with ISO15614-1.

27/09/2021 Hugo Mezin (RWC, IWE), 27.09.2021

Location Date of Issue Examiner or Examining body
 WELDING PROCEDURE QUALIFICATION RECORD (WPQR)
(EN / ISO 15614-1:2017)
Welding Procedure Qualification-Test certificate
Manufacturer’s WPQR No: WOPEX_007
Manufacturer’s pWPS No: WOPEX_16-01/02
Manufacturer’s Record of Test No – R000008_210125-131648
Manufacturer: WOPEX Manufacturing India Pvt Ltd
Address : Plot No. A-21/7-22,
Examiner or Examining body:
Village-Khalumbre (Khed),
Chakan MIDC Phase II Mr. Hugo Mezin (RWC-Level A, IWE)
Code/Testing Standard: EN / ISO 15614-1:2017 Level 2
Date of welding: 03.01.2021
Qualification Details
Details Actual Range of qualification
Welding Process(es) TIG -141 TIG -141
Type of joint and weld Butt joint (Full penetration) BW (ss nb, ss mb, bs)
Parent metal group(s) and sub- ISO 15608 – G1.2 ISO15608- G1.1, 1.2
group(s)
Parent metal thickness (mm): 12 3 - 24
Weld metal thickness (mm): s 12 s ≤ 24
Single run / Multi run: Multi run Multi run
Filler material designation: ISO636-A-W 42 3 W2Ti ISO636-A-W 42 3 W2Ti
(SFA5.18 ER70S-2)
Filler material make: ADOR Any
Filler Material size: Ø 2.4 mm Any
Throat thickness (mm): NA NA
Outside pipe diameter (mm): 60 ≥ 30
Designation of shielding ISO14175- I1 (Ar.99.99%) ISO 14175- I1
gas/flux:
Designation of backing gas NA NA
Type of polarity: DCEN DCEN
Transfer mode: NA NA
Heat input (KJ/mm) 0.68 /1.06 0.51 – 1.33
Welding positions: PH PA, PC, PH
Pre-heat temperature: 25⁰ C min. 22⁰C
Post heating: NA NA
Inter pass temperature: 250⁰ C ≤ 300⁰ C
Post weld -heat-treatment: NA NA
Other information: NA NA
We confirm that the statement in this record are correct and that the test piece were prepared, welded, tested and
have fulfilled the requirements in accordance with ISO15614-1.

27/09/2021 Hugo Mezin (RWC, IWE), 27.09.2021

Location Date of Issue Examiner or Examining body
 WELDING PROCEDURE QUALIFICATION RECORD (WPQR)
(EN / ISO 15614-1:2017)
Welding Procedure Qualification-Test certificate
Manufacturer’s WPQR No: WOPEX_008
Manufacturer’s pWPS No: WOPEX_14-01
Manufacturer’s Record of Test No – R000008_210125-150819
Manufacturer: WOPEX Manufacturing India Pvt Ltd
Address : Plot No. A-21/7-22,
Examiner or Examining body:
Village-Khalumbre (Khed),
Chakan MIDC Phase II Mr. Hugo Mezin (RWC-Level A, IWE)
Code/Testing Standard: EN / ISO 15614-1:2017 Level 2
Date of welding: 02.01.2021
Qualification Details
Details Actual Range of qualification
Welding Process(es) TIG -141 TIG -141
Type of joint and weld T joint (Fillet weld) T joint (Fillet weld)
Parent metal group(s) and sub- ISO 15608 – G1.2 ISO15608- G1.1, 1.2
group(s)
Parent metal thickness (mm): P-8 / T-8 3 - 16
Weld metal thickness (mm): NA NA
Single run / Multi run: Multi run Multi run
Filler material designation: ISO636-A-W 42 3 W2Ti ISO636-A-W 42 3 W2Ti
(SFA5.18 ER70S-2)
Filler material make: ADOR Any
Filler Material size: Ø 2.4 mm Any
Throat thickness (mm): a5 No restriction
Outside pipe diameter (mm): 60 ≥ 30
Designation of shielding ISO14175- I1 (Ar.99.99%) ISO 14175- I1
gas/flux:
Designation of backing gas NA NA
Type of polarity: DCEN DCEN
Transfer mode: NA NA
Heat input (KJ/mm) 1.19 /1.47 0.89 – 1.84
Welding positions: PB PA, PB
Pre-heat temperature: 25⁰ C min. 22⁰C
Post heating: NA NA
Inter pass temperature: 250⁰ C ≤ 300⁰ C
Post weld -heat-treatment: NA NA
Other information: NA NA
We confirm that the statement in this record are correct and that the test piece were prepared, welded, tested and
have fulfilled the requirements in accordance with ISO15614-1.

27/09/2021 Hugo Mezin (RWC, IWE), 27.09.2021

Location Date of Issue Examiner or Examining body
 WELDING PROCEDURE QUALIFICATION RECORD (WPQR)
(EN / ISO 15614-1:2017)
Welding Procedure Qualification-Test certificate
Manufacturer’s WPQR No: WOPEX_009
Manufacturer’s pWPS No: WOPEX_07-01
Manufacturer’s Record of Test No – R000008_210119-141452
Manufacturer: WOPEX Manufacturing India Pvt Ltd
Address : Plot No. A-21/7-22,
Examiner or Examining body:
Village-Khalumbre (Khed),
Chakan MIDC Phase II Mr. Hugo Mezin (RWC-Level A, IWE)
Code/Testing Standard: EN / ISO 15614-1:2017 Level 2
Date of welding: 25.12.2020
Qualification Details
Details Actual Range of qualification
Welding Process(es) TIG -141 TIG -141
Type of joint and weld T joint (Fillet weld) T joint (Fillet weld)
Parent metal group(s) and sub- ISO 15608 – G8.1 ISO15608- G8.1
group(s)
Parent metal thickness (mm): 20 3 - 40
Weld metal thickness (mm): NA NA
Single run / Multi run: Multi run Multi run
Filler material designation: ISO14343-A-W 19 9 L Si ISO14343-A-W 19 9 L Si
(SFA5.9 ER308LSi)
Filler material make: VENUS Any
Filler Material size: Ø 2.4 mm Any
Throat thickness (mm): a5 No restriction
Outside pipe diameter (mm): 40 ≥ 20
Designation of shielding ISO14175- I1 (Ar.99.99%) ISO 14175- I1
gas/flux:
Designation of backing gas NA NA
Type of polarity: DCEN DCEN
Transfer mode: NA NA
Heat input (KJ/mm) 0.85 /0.90 No restriction
Welding positions: PB PA, PB
Pre-heat temperature: 25⁰ C min. 22⁰C
Post heating: NA NA
Inter pass temperature: 250⁰ C ≤ 300⁰ C
Post weld -heat-treatment: NA NA
Other information: NA NA
We confirm that the statement in this record are correct and that the test piece were prepared, welded, tested and
have fulfilled the requirements in accordance with ISO15614-1.

27/09/2021 Hugo Mezin (RWC, IWE), 27.09.2021

Location Date of Issue Examiner or Examining body
 WELDING PROCEDURE QUALIFICATION RECORD (WPQR)
(EN / ISO 15614-1:2017)
Welding Procedure Qualification-Test certificate
Manufacturer’s WPQR No: WOPEX_010
Manufacturer’s pWPS No: WOPEX_19-01/02
Manufacturer’s Record of Test No – R000008_210125-124437
Manufacturer: WOPEX Manufacturing India Pvt Ltd
Address : Plot No. A-21/7-22,
Examiner or Examining body:
Village-Khalumbre (Khed),
Chakan MIDC Phase II Mr. Hugo Mezin (RWC-Level A, IWE)
Code/Testing Standard: EN / ISO 15614-1:2017 Level 2
Date of welding: 08.01.2021
Qualification Details
Details Actual Range of qualification
Welding Process(es) MAG- 135(Partly Mechanized) MAG- 135(Partly Mechanized)
Type of joint and weld Butt joint (Full penetration) Butt joint (Full penetration)
Parent metal group(s) and sub- ISO 15608 – G1.2 & 8.1 ISO15608- G1.1, 1.2 and G8.1
group(s)
Parent metal thickness (mm): 4/4 3 – 5.2
Weld metal thickness (mm): s4 s≤8
Single run / Multi run: Single run Single run
Filler material designation: ISO14343-A-G 23 12 L Si ISO14343-A-G 23 12 L Si
(SFA5.9 ER309LSi)
Filler material make: SUPERON Any
Filler Material size: Ø 1 mm Any
Throat thickness (mm): NA NA
Outside pipe diameter (mm): 48 ≥ 24
Designation of shielding ISO14175- M12 (Ar.98%+ Co2-2%) ISO 14175- M12
gas/flux:
Designation of backing gas NA NA
Type of polarity: DCEP DCEP
Transfer mode: Globular Globular, Spray
Heat input (KJ/mm) 0.68 0.51 – 0.85
Welding positions: PC PA, PC
Pre-heat temperature: 25⁰ C min. 22⁰C
Post heating: NA NA
Inter pass temperature: NA NA
Post weld -heat-treatment: NA NA
Other information: NA NA
We confirm that the statement in this record are correct and that the test piece were prepared, welded, tested and
have fulfilled the requirements in accordance with ISO15614-1.

27/09/2021 Hugo Mezin (RWC, IWE), 27.09.2021

Location Date of Issue Examiner or Examining body
 WELDING PROCEDURE QUALIFICATION RECORD (WPQR)
(EN / ISO 15614-1:2017)
Welding Procedure Qualification-Test certificate
Manufacturer’s WPQR No: WOPEX_012
Manufacturer’s pWPS No: WOPEX_08-01
Manufacturer’s Record of Test No – R000008_210119-122433
Manufacturer: WOPEX Manufacturing India Pvt Ltd
Address : Plot No. A-21/7-22,
Examiner or Examining body:
Village-Khalumbre (Khed),
Chakan MIDC Phase II Mr. Hugo Mezin (RWC-Level A, IWE)
Code/Testing Standard: EN / ISO 15614-1:2017 Level 2
Date of welding: 25.12.2020
Qualification Details
Details Actual Range of qualification
Welding Process(es) MAG- 135(Partly Mechanized) MAG- 135(Partly Mechanized)
Type of joint and weld T joint (Fillet weld) T joint (Fillet weld)
Parent metal group(s) and sub- ISO 15608 – G1.2 & 8.1 ISO15608- G1.1, 1.2 and G8.1
group(s)
Parent metal thickness (mm): 20 / 20 3 – 40
Weld metal thickness (mm): NA NA
Single run / Multi run: Single run Single run
Filler material designation: ISO14343-A-G 23 12 L Si ISO14343-A-G 23 12 L Si
(SFA5.9 ER309LSi)
Filler material make: SUPERON Any
Filler Material size: Ø 1 mm Any
Throat thickness (mm): a4 a3 – a6
Outside pipe diameter (mm): 40 ≥ 20
Designation of shielding ISO14175- M12 (Ar.98%+ Co2-2%) ISO 14175- M12
gas/flux:
Designation of backing gas NA NA
Type of polarity: DCEP DCEP
Transfer mode: Spray Globular, Spray
Heat input (KJ/mm) 1.47 1.10- 1.83
Welding positions: PB PA, PB
Pre-heat temperature: 25⁰ C min. 22⁰C
Post heating: NA NA
Inter pass temperature: NA NA
Post weld -heat-treatment: NA NA
Other information: NA NA
We confirm that the statement in this record are correct and that the test piece were prepared, welded, tested and
have fulfilled the requirements in accordance with ISO15614-1.

27/09/2021 Hugo Mezin (RWC, IWE), 27.09.2021

Location Date of Issue Examiner or Examining body
 WELDING PROCEDURE QUALIFICATION RECORD (WPQR)
(EN / ISO 15614-1:2017)
Welding Procedure Qualification-Test certificate
Manufacturer’s WPQR No: WOPEX_014
Manufacturer’s pWPS No: WOPEX_09-01
Manufacturer’s Record of Test No – R000008_210118-165151
Manufacturer: WOPEX Manufacturing India Pvt Ltd
Address : Plot No. A-21/7-22,
Examiner or Examining body:
Village-Khalumbre (Khed),
Chakan MIDC Phase II Mr. Hugo Mezin (RWC-Level A, IWE)
Code/Testing Standard: EN / ISO 15614-1:2017 Level 2
Date of welding: 17.12.2020
Qualification Details
Details Actual Range of qualification
Welding Process(es) TIG- 141 TIG- 141
Type of joint and weld T joint (Fillet weld) T joint (Fillet weld)
Parent metal group(s) and sub- ISO 15608 – G1.2 & 8.1 ISO15608- G1.1, 1.2 and G8.1
group(s)
Parent metal thickness (mm): P- 16 / T- 10 P: 3 -32, T:3 -20
Weld metal thickness (mm): NA NA
Single run / Multi run: Single run Single run
Filler material designation: ISO14343-A-W 23 12 L ISO14343-A-W 23 12 L
(SFA5.9 ER309L)
Filler material make: SUPERON Any
Filler Material size: Ø 2.4 mm Any
Throat thickness (mm): a2 a1.5 – a3
Outside pipe diameter (mm): 10 ≥5
Designation of shielding ISO14175- i1 (Ar.99.99%) ISO 14175- I1
gas/flux:
Designation of backing gas NA NA
Type of polarity: DCEN DCEN
Transfer mode: NA NA
Heat input (KJ/mm) 1.68 1.26 – 2.10
Welding positions: PB PA, PB
Pre-heat temperature: 25⁰ C min. 22⁰C
Post heating: NA NA
Inter pass temperature: NA NA
Post weld -heat-treatment: NA NA
Other information: NA NA
We confirm that the statement in this record are correct and that the test piece were prepared, welded, tested and
have fulfilled the requirements in accordance with ISO15614-1.

27/09/2021 Hugo Mezin (RWC, IWE), 27.09.2021

Location Date of Issue Examiner or Examining body