PIC16F716

PIC16F716 Rev. A Silicon/Data Sheet Errata

The PIC16F716 parts you have received conform Clarifications/Corrections to the Data
functionally to the Device Data Sheet (DS41206A) and Sheet:
the Programming Specification (DS40245B), except
for the anomalies described below. In the Device Data Sheet (DS41206A), the following
clarifications and corrections should be noted.
All problems listed here will be addressed in future
revisions of the PIC16F716 silicon.
1. Module: Oscillator Configuration
1. Module: Silicon (Rev. A4) – Programming In Figure 9-3, revise the second line of
recommended values as follows:
The oscillator circuitry may prevent proper
initialization of the Programming mode when the 10 kΩ ≤ REXT ≤ 100 kΩ (VDD < 3.0V)
part is programmed in-circuit.
FIGURE 9-3: RC OSCILLATOR MODE
Work around
Tie the OSC1/EXTCLK pin (pin 16 of 18-pin VDD
package or pin 18 of 20-pin package) to ground to
disable the oscillator during In-circuit Serial REXT
Programming™. OSC1
Internal
clock

CEXT PIC16F716
VSS
OSC2/CLKOUT
FOSC/4
Recommended values:
• 3 KΩ ≤ REXT ≤ 100 kΩ (VDD ≥ 3.0V)
• 10 KΩ ≤ REXT ≤ 100 kΩ (VDD < 3.0V)
• CEXT > 20 pF

 2004 Microchip Technology Inc. DS80184B-page 1

PIC16F716
2. Module: Electrical Characteristics
In Section 12.4, “DC Characteristics: PIC16F716
(Industrial, Extended)”, changes to parameter
numbers D033A and D042B are shown in bold and
italics below.

12.4 DC Characteristics: PIC16F716 (Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
DC CHARACTERISTICS
Operating voltage VDD range as described in DC specification
Section 12.1 “DC Characteristics: PIC16F716 (Industrial, Extended)” and
Section 12.4 “DC Characteristics: PIC16F716 (Industrial, Extended)”
Param
Sym Characteristic Min Typ† Max Units Conditions
No.
VIL Input Low Voltage
I/O ports
D030 with TTL buffer VSS — 0.8V V 4.5V ≤ VDD ≤ 5.5V
D030A VSS — 0.15VDD V otherwise
D031 with Schmitt Trigger buffer VSS — 0.2VDD V
D032 MCLR, OSC1 (in RC mode) VSS — 0.2VDD V
D033 OSC1 (in HS mode) VSS — 0.3VDD V (Note 1)
D033A OSC1 (in XT and LP modes) VSS — 0.3 V
VIH Input High Voltage
I/O ports —
D040 with TTL buffer 2.0 — VDD V 4.5V ≤ VDD ≤ 5.5V
D040A 0.25 VDD — VDD V otherwise
+ 0.8V
D041 with Schmitt Trigger buffer 0.8 VDD — VDD V For entire VDD range
D042 MCLR 0.8 VDD — VDD V
D042A OSC1 (HS) 0.7 VDD — VDD V (Note 1)
D042B OSC1 (XT and LP modes) 1.6 — VDD V
D043 OSC1 (in RC mode) 0.9 VDD — VDD V
IIL Input Leakage Current(2), (3)
D060 I/O ports — — ±1 µA Vss ≤ VPIN ≤ VDD, Pin at
high-impedance
D061 MCLR, RA4/T0CKI — — ±5 µA Vss ≤ VPIN ≤ VDD
D063 OSC1/CLKIN — — ±5 µA Vss ≤ VPIN ≤ VDD, XT, HS and LP
Oscillator modes
D070 IPURB PORTB weak pull-up current TBD 250 TBD µA VDD = 5V, VPIN = VSS
VOL Output Low Voltage
D080 I/O ports — — 0.6 V IOL = 8.5 mA, VDD = 4.5V, -40°C to +85°C
— — 0.6 V IOL = 7.0 mA, VDD = 4.5V, -40°C to
+125°C
D083 OSC2/CLKOUT (RC Oscillator mode) — — 0.6 V IOL = 1.6 mA, VDD = 4.5V, -40°C to +85°C
— — 0.6 V IOL = 1.2 mA, VDD = 4.5V, -40°C to
+125°C
VOH Output High Voltage
D090 I/O ports(3) VDD – 0.7 — — V IOH = -3.0 mA, VDD = 4.5V, -40°C to
+85°C
VDD – 0.7 — — V IOH = -2.5 mA, VDD = 4.5V, -40°C to
+125°C
D092 OSC2/CLKOUT (RC Oscillator mode) VDD – 0.7 — — V IOH = -1.3 mA, VDD = 4.5V, -40°C to
+85°C
VDD – 0.7 — — V IOH = -1.0 mA, VDD = 4.5V, -40°C to
+125°C
D150* VOD Open-Drain High Voltage — — 8.5 V RA4 pin
Capacitive Loading Specs on Output Pins
D100 COSC2 OSC2/CLKOUT pin — — 15 pF In XT, HS and LP modes when external
clock is used to drive OSC1.
D101 CIO All I/O pins and OSC2 (in RC mode) — — 50 pF
* These parameters are characterized but not tested.
† Data in “Type” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested.
Note 1: In RC Oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PICmicro® microcontroller be
driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels represent normal
operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.

DS80184B-page 2  2004 Microchip Technology Inc.

 PIC16F716
APPENDIX A: REVISION HISTORY
Rev. A Document (2/19/04)
First revision of this document.
Rev. B Document (7/12/04)
Changes made to parameter numbers D033A and
D042B in Section 12.4, “DC Characteristics:
PIC16F716 (Industrial, Extended)”.

 2004 Microchip Technology Inc. DS80184B-page 3

PIC16F716
NOTES:

DS80184B-page 4  2004 Microchip Technology Inc.

Note the following details of the code protection feature on Microchip devices:
• Microchip products meet the specification contained in their particular Microchip Data Sheet.

• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.

• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.

• Microchip is willing to work with the customer who is concerned about the integrity of their code.

• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”

Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.

Information contained in this publication regarding device Trademarks

applications and the like is intended through suggestion only
The Microchip name and logo, the Microchip logo, Accuron,
and may be superseded by updates. It is your responsibility to
dsPIC, KEELOQ, microID, MPLAB, PIC, PICmicro, PICSTART,
ensure that your application meets with your specifications.
PRO MATE, PowerSmart, rfPIC, and SmartShunt are
No representation or warranty is given and no liability is
registered trademarks of Microchip Technology Incorporated
assumed by Microchip Technology Incorporated with respect
in the U.S.A. and other countries.
to the accuracy or use of such information, or infringement of
patents or other intellectual property rights arising from such AmpLab, FilterLab, MXDEV, MXLAB, PICMASTER, SEEVAL,
use or otherwise. Use of Microchip’s products as critical SmartSensor and The Embedded Control Solutions Company
components in life support systems is not authorized except are registered trademarks of Microchip Technology
with express written approval by Microchip. No licenses are Incorporated in the U.S.A.
conveyed, implicitly or otherwise, under any intellectual Analog-for-the-Digital Age, Application Maestro, dsPICDEM,
property rights. dsPICDEM.net, dsPICworks, ECAN, ECONOMONITOR,
FanSense, FlexROM, fuzzyLAB, In-Circuit Serial
Programming, ICSP, ICEPIC, Migratable Memory, MPASM,
MPLIB, MPLINK, MPSIM, PICkit, PICDEM, PICDEM.net,
PICLAB, PICtail, PowerCal, PowerInfo, PowerMate,
PowerTool, rfLAB, rfPICDEM, Select Mode, Smart Serial,
SmartTel and Total Endurance are trademarks of Microchip
Technology Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2004, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.

Microchip received ISO/TS-16949:2002 quality system certification for

its worldwide headquarters, design and wafer fabrication facilities in
Chandler and Tempe, Arizona and Mountain View, California in
October 2003. The Company’s quality system processes and
procedures are for its PICmicro® 8-bit MCUs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.

 2004 Microchip Technology Inc. DS80184B-page 5

 WORLDWIDE SALES AND SERVICE
AMERICAS China - Beijing Singapore
Unit 706B 200 Middle Road
Corporate Office
Wan Tai Bei Hai Bldg. #07-02 Prime Centre
2355 West Chandler Blvd.
No. 6 Chaoyangmen Bei Str. Singapore, 188980
Chandler, AZ 85224-6199
Beijing, 100027, China Tel: 65-6334-8870 Fax: 65-6334-8850
Tel: 480-792-7200
Tel: 86-10-85282100 Taiwan
Fax: 480-792-7277
Fax: 86-10-85282104 Kaohsiung Branch
Technical Support: 480-792-7627
Web Address: www.microchip.com China - Chengdu 30F - 1 No. 8
Rm. 2401-2402, 24th Floor, Min Chuan 2nd Road
Atlanta Ming Xing Financial Tower Kaohsiung 806, Taiwan
3780 Mansell Road, Suite 130 No. 88 TIDU Street Tel: 886-7-536-4816
Alpharetta, GA 30022 Chengdu 610016, China Fax: 886-7-536-4817
Tel: 770-640-0034 Tel: 86-28-86766200 Taiwan
Fax: 770-640-0307 Fax: 86-28-86766599 Taiwan Branch
Boston China - Fuzhou 11F-3, No. 207
2 Lan Drive, Suite 120 Unit 28F, World Trade Plaza Tung Hua North Road
Westford, MA 01886 No. 71 Wusi Road Taipei, 105, Taiwan
Tel: 978-692-3848 Fuzhou 350001, China Tel: 886-2-2717-7175 Fax: 886-2-2545-0139
Fax: 978-692-3821 Tel: 86-591-7503506 Taiwan
Chicago Fax: 86-591-7503521 Taiwan Branch
333 Pierce Road, Suite 180 China - Hong Kong SAR 13F-3, No. 295, Sec. 2, Kung Fu Road
Itasca, IL 60143 Unit 901-6, Tower 2, Metroplaza Hsinchu City 300, Taiwan
Tel: 630-285-0071 223 Hing Fong Road Tel: 886-3-572-9526
Fax: 630-285-0075 Kwai Fong, N.T., Hong Kong Fax: 886-3-572-6459
Dallas Tel: 852-2401-1200
Fax: 852-2401-3431 EUROPE
16200 Addison Road, Suite 255
Addison Plaza China - Shanghai Austria
Addison, TX 75001 Room 701, Bldg. B Durisolstrasse 2
Tel: 972-818-7423 Far East International Plaza A-4600 Wels
Fax: 972-818-2924 No. 317 Xian Xia Road Austria
Shanghai, 200051 Tel: 43-7242-2244-399
Detroit Tel: 86-21-6275-5700 Fax: 43-7242-2244-393
Tri-Atria Office Building Fax: 86-21-6275-5060 Denmark
32255 Northwestern Highway, Suite 190 Regus Business Centre
Farmington Hills, MI 48334 China - Shenzhen
Rm. 1812, 18/F, Building A, United Plaza Lautrup hoj 1-3
Tel: 248-538-2250 Ballerup DK-2750 Denmark
Fax: 248-538-2260 No. 5022 Binhe Road, Futian District
Shenzhen 518033, China Tel: 45-4420-9895 Fax: 45-4420-9910
Kokomo Tel: 86-755-82901380 France
2767 S. Albright Road Fax: 86-755-8295-1393 Parc d’Activite du Moulin de Massy
Kokomo, IN 46902 China - Shunde 43 Rue du Saule Trapu
Tel: 765-864-8360 Batiment A - ler Etage
Room 401, Hongjian Building, No. 2
Fax: 765-864-8387 91300 Massy, France
Fengxiangnan Road, Ronggui Town, Shunde
Los Angeles District, Foshan City, Guangdong 528303, China Tel: 33-1-69-53-63-20
Tel: 86-757-28395507 Fax: 86-757-28395571 Fax: 33-1-69-30-90-79
25950 Acero St., Suite 200
Mission Viejo, CA 92691 China - Qingdao Germany
Tel: 949-462-9523 Steinheilstrasse 10
Rm. B505A, Fullhope Plaza,
Fax: 949-462-9608 D-85737 Ismaning, Germany
No. 12 Hong Kong Central Rd.
Tel: 49-89-627-144-0
San Jose Qingdao 266071, China
Fax: 49-89-627-144-44
1300 Terra Bella Avenue Tel: 86-532-5027355 Fax: 86-532-5027205
Italy
Mountain View, CA 94043 India
Via Salvatore Quasimodo, 12
Tel: 650-215-1444 Divyasree Chambers
20025 Legnano (MI)
Fax: 650-961-0286 1 Floor, Wing A (A3/A4)
Milan, Italy
No. 11, O’Shaugnessey Road
Toronto Tel: 39-0331-742611
Bangalore, 560 025, India
6285 Northam Drive, Suite 108 Fax: 39-0331-466781
Tel: 91-80-22290061 Fax: 91-80-22290062
Mississauga, Ontario L4V 1X5, Canada Netherlands
Japan
Tel: 905-673-0699 Waegenburghtplein 4
Fax: 905-673-6509 Yusen Shin Yokohama Building 10F
NL-5152 JR, Drunen, Netherlands
3-17-2, Shin Yokohama, Kohoku-ku,
Tel: 31-416-690399
Yokohama, Kanagawa, 222-0033, Japan
ASIA/PACIFIC Fax: 31-416-690340
Tel: 81-45-471- 6166 Fax: 81-45-471-6122
United Kingdom
Australia Korea
505 Eskdale Road
Microchip Technology Australia Pty Ltd 168-1, Youngbo Bldg. 3 Floor
Winnersh Triangle
Unit 32 41 Rawson Street Samsung-Dong, Kangnam-Ku
Wokingham
Epping 2121, NSW Seoul, Korea 135-882
Berkshire, England RG41 5TU
Sydney, Australia Tel: 82-2-554-7200 Fax: 82-2-558-5932 or
Tel: 44-118-921-5869
Tel: 61-2-9868-6733 82-2-558-5934
Fax: 44-118-921-5820
Fax: 61-2-9868-6755
07/12/04

DS80184B-page 6  2004 Microchip Technology Inc.