VIKING® HEAVY-DUTY ABRASIVE LIQUID PUMPS Section 410

SERIES 4625 Page 410.1

Issue H

FEATURES

SERIES 4625 Pumps

Cutaway View
“FH” size shown.

MECHANICAL SEAL (SERIES 4625) SERIES 4625 Pumps

“F” & “FH” SIZES “H” — “M” SIZES Cutaway View
“KK” size shown.

① Stainless Steel Drive Pins (2) ① Stainless Steel Drive Pin

② Stainless Steel Wavy Spring ② Viton® Shaft O-Ring
③ Viton® Shaft O-Ring ③ Viton® O-Rings
④ Silicon Carbide Faces ④ Silicon Carbide Faces
⑤ Stainless Steel Retainers ⑤ Stainless Steel Metal Retainer
⑥ Viton® O-Rings ⑥ Stainless Steel Spring
⑦ Viton® O-Ring ⑦ Viton® O-Ring
⑧ Stainless Steel ⑧ Stainless Steel
Anti-Rotation Pins (2) Anti-Rotation Pins (2)

FEATURES
Approximately ⅓ to ½ Normal Speed
① RPM compared to standard
Heavy-Duty Series 125 pumps
① Maximum
150 PSI (10 BAR)
PSI
① Viscosity
38 to 250,000 SSU (3 to 55,000 cSt)
Range
REVOLVABLE PUMP CASING TUNGSTEN CARBIDE BEARINGS
(Standard Equipment) (Standard Equipment)
All “H” size and larger Series 4625 Tungsten carbide bearings are used
pumps are equipped with pump
casings that can be turned to eight
in “H” thru “M” size Series 4625
pumps. This type of bearing
GPM ¾-1½-5-10-25-35-50-65-110-140
positions except the “LQ” and “LL”
sizes. These can be turned in all
operating on a tungsten carbide
idler pin, has proved itself to be su-
(m³/hr .2-.3-1-2-6-8-11-15-25-32)
positions except for a port in the 6 perior to other materials in most (Nominal Rating)
②
o’clock position. Relief valve must abrasive liquid applications. “F” and
point to suction port in all cases. “FH” sizes have nitralloy idler pin. Viking’s Series 4625 heavy-duty abrasive liquid pumps
Flush line must be from discharge port No idler bushing. have proved themselves highly superior in pumping
to seal chamber to function properly.
paints, inks and other abrasive liquids.
With tungsten carbide bearings and silicon carbide
mechanical seals, these pumps have doubled and tripled
the former service life of such pumping equipment. These
pumps are built in the range of sizes shown above and
are suitable for all paints, inks and other abrasive liquids
from a minimum viscosity of 38 SSU to heavy viscous
POSITIVE-LOCK THRUST CONTROL types. Pressure relief valve standard equipment.
All “H” size and larger Series 4625 pumps are manufactured with positive- ① See following pages or consult factory for specific recommendations on individual
lock thrust control for accurate axial positioning of rotor and shaft. Illustration models and sizes.
shows bearing and double end cap arrangement.
② Nominal capacities based on handling thin liquids.

Viton ® — Registered trademark of DuPont Performance Elastomers. Metric conversions are based on US measurements and rounded to the nearest whole number.

VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2013

 Section 410 VIKING® HEAVY-DUTY ABRASIVE LIQUID PUMPS
Page 410.2 SERIES 4625
Issue H

UNMOUNTED PUMPS

“H” and “HL” Sizes

“K” “KK” and “L” Sizes

“LQ” and “LL” Sizes
Viking’s Series 4625 heavy-duty abrasive liquid “Q” and “M” Sizes
pumps have proved, through extensive usage, they can
handle inks, paints and other highly abrasive materials
efficiently and economically.
3. Percentage and type of 5. Specific gravity.
Reduced speeds of this line of pumps also enables
them to deliver these abrasive liquids over a much solids present in liquid. 6. Capacity of pump.
longer service life. 4. Temperature of liquid. 7. Suction lift or head.
In ordering these pumps, the following information 8. Discharge pressure.
must be given to assure good service: Dimensions for Unmounted Pumps—See Page 410.8.
1. Liquid pumped.
2. Viscosity of liquid

CONSTRUCTION — SERIES 4625 (“F” and “fh” SIZES)

Construction Casing Head Rotor and Shaft Idler Idler Pin Casing Bushing Mechanical Seal

② Silicon Carbide
Steel Fitted Iron Iron Hardened Steel Hardened Steel Nitralloy Bronze
and Viton®

CONSTRUCTION — SERIES 4625 (“H” THROUGH “M” SIZES)

Bushings Internal
Pump Rotor Idler Mechanical Relief
Construction Casing Head Bracket Rotor Idler Shaft Pin Bracket Idler Seal Valve
Standard ① Tungsten Tungsten ② Silicon Carbide
Iron Iron Iron Iron ⑧ Iron Steel Bronze Iron
Construction Carbide Carbide and Viton®
Steel Hardened Hardened ① Tungsten Tungsten ② Silicon Carbide
Iron Iron Iron Steel Bronze Iron
Fitted Steel Steel Carbide Carbide and Viton®

SPECIFICATIONS — UNMOUNTED PUMPS

⑥ Motor HP Required Steel Fitted ④ Maximum Recommended ⑦ Maximum Approximate
Nominal At Rated Speed Maximum Construction Discharge Pressure At Recommended Shipping
Model Port Pump Pumping 100 SSU Hydrostatic Recommended Nominal Rated Speeds Temperature for Weight
Number Size Rating Liquid Pressure Above This Viscosity PSIG Cataloged Pump With Valve
③ Mech. 50 PSI 100 PSI 38 to 100 to 750 SSU
Seal Inches GPM (m³/HR) RPM (3 BAR) (7 BAR) PSIG (BAR) SSU (cSt) 100 SSU 750 SSU and Up °F. (°C.) Pounds (KG)
F4625 ½ ¾ (.2) 870 ¼ ¼ 400 (28) ..... 50 100 100 250 (121) 6 (2.5)
FH4625 ½ 1½ (.3) 870 ¼ ¼ 400 (28) ..... 50 100 100 250 (121) 7 (3)
H4625 1½ 5 (1) 640 ½ ¾ 400 (28) 25,000 (5,500) 50 100 150 300 (149) 38 (17)
HL4625 1½ 10 (2) 640 ½ 1 400 (28) 7,500 (1,650) 50 100 150 300 (149) 40 (18)
K4625 2 25 (6) 280 1 3 400 (28) 25,000 (5,500) 50 100 150 300 (149) 105 (48)
KK4625 2 35 (8) 280 1 3 400 (28) 25,000 (5,500) 50 100 150 300 (149) 110 (50)
L4625 2 50 (11) 230 3 5 400 (28) 25,000 (5,500) 50 100 150 300 (149) 155 (70)
LQ4625 ⑤ 2½ 50 (11) 230 3 5 400 (28) 25,000 (5,500) 50 100 150 300 (149) 180 (82)
LL4625 ⑤3 65 (15) 230 3 5 400 (28) 2,500 (550) 50 100 150 300 (149) 200 (91)
Q4625 ⑤3 110 (25) 190 5 10 400 (28) 7,500 (1,650) 50 100 125 300 (149) 460 (209)
M4625 ⑤4 140 (32) 155 7 15 400 (28) 25,000 (5,500) 50 100 125 300 (149) 620 (281)
① Tungsten Carbide idler pins for all sizes except “Q” and “M”. These two sizes have and or at other speeds, see performance curves, found in the pump selector on
a tungsten carbide sleeve over a steel pin. www.vikingpump.com. If suction pressure exceeds 50 PSIG (3 BAR) consult factory.
② Other seal materials available. Check factory for construction recommendations for ⑤ Ports are suitable for use with 125# ANSI cast iron or 150# ANSI steel companion
handling liquids containing acetone or ketone type solvents. flanges or flanged fittings. All others tapped for standard pipe.
③ Viton® elastomer used as standard in mechanical seal of Series 4625 pumps. ⑥ Nominal rating based on handling thin liquids.
Kalrez® elastomers are available as an option for other applications. ⑦ For higher temperatures, provide details for recommendations.
④ For maximum recommended discharge pressures when handling other viscosities ⑧ “G”, “H” and “HL” sizes have powdered metal idler.
Viton ® and Kalrez® are Registered trademarks of DuPont Performance Elastomers. Metric conversions are based on US measurements and rounded to the nearest whole number.

VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2013

VIKING® HEAVY-DUTY ABRASIVE LIQUID PUMPS Section 410

SERIES 4625 Page 410.3

Issue H

VIKING HELICAL GEAR REDUCTION UNITS (“R” DRIVE)

SERIES 4625 Pumps

with “R” Drive “B” Reducer

SERIES 4625 Pumps

with “R” Drive “A” Reducer
SERIES 4625 Pumps
Viking’s heavy-duty Series 4625 abrasive liquid with “R” Drive “C” Reducer
pumps are available with helical gear reducers that
have been specifically developed for efficient operation
with Viking heavy-duty pumps. These rugged, compact,
exceptionally quiet gear reducers come in three sizes:
the “small” A size, “medium” B size and “large” C size.
The “A” size reducer, available with four gear ratios
(2.24, 2.76, 3.43 and 4.17 to 1), is ideally suited for use
with the “H” and “HL” size pumps. This reducer is bracket
mounted and requires couplings on both the input and
output shafts. With the “A” size reducer and 1200 or The large “C” size reducer also is available with
1800 RPM motors, the “H” and “HL” size pumps can be two gear ratios, 6.24 to 1 and 7.95 to 1. It is normally
used to cover a capacity range from 1.7 to 10.9 GPM. used with the “Q” or “M” size pumps. Like the “A” and
The medium size “B” helical gear reducer is available “B” reducers, the “C” reducer is bracket mounted and
with four gear ratios from 4.19 to 1 to 7.65 to 1. This requires flexible couplings both for the input and output
size normally is used with pump sizes “K” through “LL”. shafts. With the “C” reducer, “Q” and “M” size pumps,
Like the “A” reducer, the “B” reducer is bracket mounted driven by 1200 RPM motors, can cover a capacity range
and requires couplings on both the input and the output to 160 GPM.
shafts. With the “B” reducer, “K” through “LL” pumps Dimensions for “R” Drive Units— See Pages 410.9 and 410.10.
driven by 1200 or 1800 RPM motors, can be used to
cover a capacity range to 61 GPM.

SPECIFICATIONS — “R” DRIVE UNITS

Motor HP Steel Fitted ② ⑤ Maximum Approximate
④ Required At Construction Maximum Recommended Recommended Shipping Weight
Nominal Rated Speed Maximum Recommended Discharge Pressure At Temperature With Valve
Model Port Pump Pumping 100 SSU Hydrostatic Above Nominal Rated Speeds for Cataloged (Less Power)
Number Size Rating Liquid Pressure This Viscosity PSIG Pump Pounds

① Mech. 50 PSI 100 PSI 38 to 100 to 750 SSU “A” “B” “C”
Seal Inches GPM (m³/HR) RPM (3 BAR) (7 BAR) PSIG (BAR) SSU (cSt) 100 SSU 750 SSU And Up °F. (°C.) Reducer Reducer Reducer
H4625R 1½ 5 (1) 640 ½ ¾ 400 (28) 25,000 (5,500) 50 100 150 250 (121) 125 (57) ... ...
HL4625R 1½ 10 (2) 640 ½ 1 400 (28) 7,500 (1,650) 50 100 150 250 (121) 130 (59) ... ...
K4625R 2 25 (6) 280 1 3 400 (28) 25,000 (5,500) 50 100 150 250 (121) ... 327 (148) ...
KK4625R 2 35 (8) 280 1½ 3 400 (28) 25,000 (5,500) 50 100 150 250 (121) ... 334 (152) 550 (250)
L4625R 2 50 (11) 230 3 5 400 (28) 25,000 (5,500) 50 100 150 250 (121) ... 380 (173) 590 (268)
LQ4625R ③ 2½ 50 (11) 230 3 5 400 (28) 25,000 (5,500) 50 100 150 250 (121) ... 420 (191) 630 (286)
LL4625R ③3 65 (15) 230 3 5 400 (28) 2,500 (550) 50 100 150 250 (121) ... 460 (209) 670 (304)
Q4625R ③3 110 (25) 190 5 10 400 (28) 7,500 (1,650) 50 100 125 250 (121) ... ... 1020 (463)
M4625R ③4 140 (32) 155 7½ 15 400 (28) 25,000 (5,500) 50 100 125 250 (121) ... ... 1160 (481)
① Viton® elastomer used as standard in mechanical seal of Series 4625 pumps. ③ Ports are suitable for use with 125# ANSI cast iron or 150# ANSI steel companion
Kalrez® elastomers are available as an option for other applications. flanges or flanged fittings. All others tapped for standard pipe.
② For maximum recommended discharge pressures when handling other viscosities ④ Nominal rating based on handling thin liquids.
and or at other speeds, see performance curves, found in the pump selector on ⑤ For higher temperatures, provide details for recommendations.
www.vikingpump.com. If suction pressure exceeds 50 PSIG (3 BAR) consult factory.
Metric conversions are based on US measurements and rounded to the nearest whole number.
Viton ® and Kalrez® are Registered trademarks of DuPont Performance Elastomers.

VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2013

 Section 410 VIKING® HEAVY-DUTY ABRASIVE LIQUID PUMPS
Page 410.4 SERIES 4625
Issue H

VIKING HELICAL GEAR REDUCER UNITS (“R” DRIVE)

OUTSTANDING FEATURES
1. Mounts NEMA standard motors, 1200 or 1800 4. Compact, narrow and low to fit in small space and
RPM. (5 HP, 1800 RPM maximum with “A” reducer; low overhead.
7½ HP, 1800 RPM maximum with “B” reducer, and 5. Pump, motor or reducer can be removed without
15 HP, 1200 RPM maximum with “C” reducer when dis­turbing the other two components.
used with Series 4625 pumps.) 6. Units with “A”, “B” and “C” reducers have standard
2. Complete reducers within a size may be inter- flexible coupling with guard between power and re­
changed on a Viking pump unit to obtain desired ducer as well as between reducer and pump.
pump speeds and capacities. Thus the four 7. Oil and weather tight for outdoor service.
gear ratios within the “A” size reducer may be 8. Ball bearings throughout.
interchanged within the size by selecting the proper 9. Reducers easily adjustable to different motor
pinion and gear of a common ratio. Similarly, all center heights.
four “B” reducers are interchangeble on each 10. Self-supported. Not hung on pump or motor shafts.
respective series of “B” reducer units. Both sizes of No radial load on pump or motor shafts.
reducers are interchangeable on each respective 11. “A” reducers have ¾” dia., ³⁄₁₆” key input and output
series of “C” reducer units. shafts; “B” reducers have 1” dia., ¼” key input shaft
3. Quiet operation. High hardness helical gears run and 1⅛” dia., ¼” key output shaft; “C” reducers
in a bath of oil. have 1⅜” dia., ⁵⁄₁₆” key input and output shafts.

HELICAL REDUCER SPECIFICATIONS AND PUMP CAPACITY TABLE — “A” SIZE

① PUMP MODELS AND CAPACITY GPM ② WITH SIZE “A” REDUCER
Maximum H4625R HL4625R
Motor Reducer Motor Pump
RPM Ratio HP RPM 50 PSI (3 BAR) 100 PSI (7 BAR) 50 PSI (3 BAR) 100 PSI (7 BAR)
2.76 to 1 5 640 5.3 5.1 10.9 10.5
1800 3.43 to 1 3 520 4.2 3.9 8.6 8.2
4.17 to 1 3 420 3.3 3.0 6.8 6.4
2.24 to 1 3 520 4.2 3.9 8.6 8.2
2.76 to 1 3 420 3.3 3.0 6.8 6.4
1200
3.43 to 1 2 350 2.6 2.3 5.4 5.0
4.17 to 1 2 280 2.0 1.7 4.2 3.8

HELICAL REDUCER SPECIFICATIONS AND PUMP CAPACITY TABLE — “B” SIZE

PUMP MODELS AND CAPACITY GPM ② WITH SIZE “B” REDUCER
① K4625R KK4625R L4625R or LQ4625R LL4625R
Maximum
Motor Reducer Motor Pump 50 PSI 100 PSI 50 PSI 100 PSI 50 PSI 100 PSI 50 PSI 100 PSI
RPM Ratio HP RPM (3 BAR) (7 BAR) (3 BAR) (7 BAR) (3 BAR) (7 BAR) (3 BAR) (7 BAR)
6.27 to 1 7½ 280 27 26 34 33 61 60 75 74
1800
7.65 to 1 5 230 22 21 27 26 50 49 61 60
4.19 to 1 7½ 280 27 26 34 33 61 60 75 74
5.06 to 1 7½ 230 22 21 27 26 50 49 61 60
1200
6.27 to 1 5 190 18 17 22 21 40 39 50 49
7.65 to 1 3 155 14 13 17 16 31 30 38 37

HELICAL REDUCER SPECIFICATIONS AND PUMP CAPACITY TABLE — “C” SIZE

PUMP MODELS AND CAPACITY GPM ② WITH SIZE “C” REDUCER

① KK4625R L4625R or LQ4625R LL4625R Q4625R M4625R

Maximum
Motor Reducer Motor Pump 200 PSI 150 PSI 200 PSI 150 PSI 200 PSI 50 PSI 100 PSI 50 PSI 75 PSI
RPM Ratio HP RPM (14 BAR) (10 BAR) (14 BAR) (10 BAR) (14 BAR) (3 BAR) (7 BAR) (3 BAR) (5 BAR)
6.24 to 1 10 190 20 38 37 48 46 89 84 160 153
1200
7.95 to 1 10 155 15 29 28 36 34 64 59 122 115

① Recommended maximum motor horsepower based on 8-10 hour per day Section 610 or Technical Service Manual (TSM-610) to determine reducer
service (Service Factor of 1.0). For other time length of service per day, see capabilities.
Service Factor table and Reducer Horsepower tables in General Catalog ② Capacities are based on 100 SSU (21 cSt) liquid and 15” Mercury Vacuum.
Metric conversions are based on US measurements and rounded to the nearest whole number.

VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2013

VIKING® HEAVY-DUTY ABRASIVE LIQUID PUMPS Section 410

SERIES 4625 Page 410.5

Issue H

GEAR REDUCER DRIVE UNITS (“P” DRIVE)

SERIES 4625 Pumps

with “P” Drive
Viking’s Heavy-Duty Series 4625, abrasive liquid
pumps, in sizes from “K” through “M” (25 to 140 GPM)
are available in the “P” drive arrangement.
All of these heavy-duty abrasove liquid pump units are
mounted on formed steel bases. All mount a separate
heavy-duty gear reducer with flexible couplings with
guards between pump, reducer and motor.
Dimensions for “P” Drive Units — Consult Factory.

SPECIFICATIONS — “P” DRIVE UNITS

⑤ Motor HP Required Steel Fitted ③ Maximum Recommended Maximum Approximate
Nominal At Rated Speed Maximum Construction Discharge Pressure At Recommended Shipping Weight With
Model Port Pump Pumping 100 SSU Hydrostatic Recommended Nominal Rated Speeds Temperature for Valve and Reducer
Number Size Rating Liquid Pressure Above This Viscosity PSIG Cataloged Pump (Less Power)
50 PSI 100 PSI 38 to 100 to 750 SSU
① Mech. Seal Inches GPM (m³/HR) RPM (3 BAR) (7 BAR) PSIG (BAR) SSU (cSt) 100 SSU 750 SSU And Up °F. (°C.) Pounds (KG)
K4625P 2 25 (6) 280 1 3 400 (28) 25,000 (5,500) 50 100 150 250 (121) 338 (153)
KK4625P 2 35 (8) 280 1½ 3 400 (28) 25,000 (5,500) 50 100 150 250 (121) 343 (156)
L4625P 2 50 (11) 230 3 5 400 (28) 25,000 (5,500) 50 100 150 250 (121) 383 (174)
LQ4625P ③ 2½ 50 (11) 230 3 5 400 (28) 25,000 (5,500) 50 100 150 250 (121) 423 (192)
LL4625P ③3 65 (15) 230 3 5 400 (28) 2,500 (550) 50 100 150 250 (121) 463 (210)
Q4625P ③3 110 (25) 190 5 10 400 (28) 7,500 (1,650) 50 100 125 250 (121) 781 (782)
M4625P ③4 140 (32) 155 7½ 15 400 (28) 25,000 (5,500) 50 100 125 250 (121) 916 (416)

① Viton® elastomer used as standard in mechanical seal of Series 4625 pumps. ③ Ports are suitable for use with 125# ANSI cast iron or 150# ANSI steel com­panion
Kalrez® elastomers are available as an option for other applications. flanges or flanged fittings. All others tapped for standard pipe.
② For maximum recommended discharge pressures when handling other vis­cosities ④ Nominal rating based on handling thin liquids.
and/or at other speeds, see performance curves, found in the pump selector on ⑤ For higher temperatures, provide details for recommendations.
www.vikingpump.com. If suction pressure exceeds 50 PSIG (3 BAR), consult
factory.
Viton ® and Kalrez® are Registered trademarks of DuPont Performance Elastomers. Metric conversions are based on US measurements and rounded to the nearest whole number.

VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2013

Section 410 VIKING® HEAVY-DUTY ABRASIVE LIQUID PUMPS
Page 410.6 SERIES 4625
Issue H

DIRECT DRIVE UNITS (“D” DRIVE)

SERIES 4625 Pumps

with “D” Drive
(vari-drive unit)

SERIES 4625 Pumps

with “D” Drive
(gearhead motor)

Viking Direct Drive Series 4625 heavy-duty abrasive In this assembly, the pump is mounted on the end of
liquid pumps from “H” through “M” sizes (5 to 140 GPM) a rectangular steel base and connected to a gearhead
are furnished direct driven from gearhead motors, or motor by means of a flexible coupling with guard.
can be connected to vari-drive units for handy change Compactness and quiet operation are assured with this
in speed and pump capacity. type of mounting.

Dimensions for “D” Drive Units—See Page 410.10.

SPECIFICATIONS — “D” DRIVE UNITS

⑤ Motor HP Required Steel Fitted ③ Maximum Recommended Maximum Approximate
Nominal At Rated Speed Maximum Construction Discharge Pressure At Recommended Shipping Weight
Model Port Pump Pumping 100 SSU Hydrostatic Recommended Nominal Rated Speeds Temperature for With Valve
Number Size Rating Liquid Pressure Above This Viscosity PSIG Cataloged Pump (Less Power)
50 PSI 100 PSI 38 to 100 to 750 SSU
① Mech. Seal Inches GPM (m³/HR) RPM (3 BAR) (7 BAR) PSIG (BAR) SSU (cSt) 100 SSU 750 SSU And Up °F. (°C.) Pounds (KG)
H4625D 1½ 5 (1) 640 ½ ¾ 400 (28) 25,000 (5,500) 50 100 150 250 (121) 70 (32)
HL4625D 1½ 10 (2) 640 ½ 1 400 (28) 7,500 (1,650) 50 100 150 250 (121) 90 (41)
K4625D 2 25 (6) 280 1 3 400 (28) 25,000 (5,500) 50 100 150 250 (121) 220 (100)
KK4625D 2 35 (8) 280 1½ 3 400 (28) 25,000 (5,500) 50 100 150 250 (121) 250 (114)
L4625D 2 50 (11) 230 3 5 400 (28) 25,000 (5,500) 50 100 150 250 (121) 310 (141)
LQ4625D ③ 2½ 50 (11) 230 3 5 400 (28) 25,000 (5,500) 50 100 150 250 (121) 350 (159)
LL4625D ③3 65 (15) 230 3 5 400 (28) 2,500 (550) 50 100 150 250 (121) 415 (188)
Q4625D ③3 110 (25) 190 5 10 400 (28) 7,500 (1,650) 50 100 125 250 (121) 810 (368)
M4625D ③4 140 (32) 155 7½ 15 400 (28) 25,000 (5,500) 50 100 125 250 (121) 970 (440)

① Viton® elastomer used as standard in mechanical seal of Series 4625 pumps. ③ Ports are suitable for use with 125# ANSI cast iron or 150# ANSI steel com­panion
Kalrez® elastomers are available as an option for other applications. flanges or flanged fittings. All others tapped for standard pipe.
② For maximum recommended discharge pressures when handling other vis­cosities ④ Nominal rating based on handling thin liquids.
and/or at other speeds, see performance curves, found in the pump selector on ⑤ For higher temperatures, provide details for recommendations.
www.vikingpump.com. If suction pressure exceeds 50 PSIG (3 BAR), consult factory.
Viton ® and Kalrez® are Registered trademarks of DuPont Performance Elastomers. Metric conversions are based on US measurements and rounded to the nearest whole number.

VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2013

VIKING® HEAVY-DUTY ABRASIVE LIQUID PUMPS Section 410

SERIES 4625 Page 410.7

Issue H

V-BELT DRIVE UNITS (“V” DRIVE)

SERIES 4625 Pumps

with “V” Drive

The Series 4625 heavy-duty abrasive liquid pumps in

“H” through “Q” size (5 to 110 GPM) are available with
V-belt drive mounting.
The unit includes pump mounted on steel base with
totally guarded V-belt drive mounted on pump shaft and
connected to 1200 or 1800 RPM motor (“H” and “HL”
sizes) and 1200 RPM motor (“K” through “Q” sizes).
Motors mount on slide rail bases and are furnished as
extra item.
Maximum standard reduction is 4 to 1 on “H” and “HL”
sizes, 6 to 1 on “K” through “Q” sizs.
Dimensions for “P” Drive Units — Consult Factory.

SPECIFICATIONS — “V” DRIVE UNITS

⑤ Motor HP Required Steel Fitted ③ Maximum Recommended Maximum Approximate
Nominal At Rated Speed Maximum Construction Discharge Pressure At Recommended Shipping Weight
Model Port Pump Pumping 100 SSU Hydrostatic Recommended Nominal Rated Speeds Temperature for With Valve
Number Size Rating Liquid Pressure Above This Viscosity PSIG Cataloged Pump (Less Power)
50 PSI 100 PSI 38 to 100 to 750 SSU
① Mech. Seal Inches GPM (m³/HR) RPM (3 BAR) (7 BAR) PSIG (BAR) SSU (cSt) 100 SSU 750 SSU And Up °F. (°C.) Pounds (KG)
H4625V 1½ 5 (1) 640 ½ ¾ 400 (28) 25,000 (5,500) 50 100 150 250 (121) 109 (49)
HL4625V 1½ 10 (2) 640 ½ 1 400 (28) 7,500 (1,650) 50 100 150 250 (121) 114 (52)
K4625V 2 25 (6) 280 1 3 400 (28) 25,000 (5,500) 50 100 150 250 (121) 255 (116)
KK4625V 2 35 (8) 280 1½ 3 400 (28) 25,000 (5,500) 50 100 150 250 (121) 265 (120)
L4625V 2 50 (11) 230 3 5 400 (28) 25,000 (5,500) 50 100 150 250 (121) 305 (138)
LQ4625V ③ 2½ 50 (11) 230 3 5 400 (28) 25,000 (5,500) 50 100 150 250 (121) 345 (157)
LL4625V ③3 65 (15) 230 3 5 400 (28) 2,500 (550) 50 100 150 250 (121) 370 (168)
Q4625V ③3 110 (25) 190 5 10 400 (28) 7,500 (1,650) 50 100 125 250 (121) 1006 (457)

① Viton® elastomer used as standard in mechanical seal of Series 4625 pumps. ③ Ports are suitable for use with 125# ANSI cast iron or 150# ANSI steel com­panion
Kalrez® elastomers are available as an option for other applications. flanges or flanged fittings. All others tapped for standard pipe.
② For maximum recommended discharge pressures when handling other vis­cosities ④ Nominal rating based on handling thin liquids.
and/or at other speeds, see performance curves, found in the pump selector on ⑤ For higher temperatures, provide details for recommendations.
www.vikingpump.com. If suction pressure exceeds 50 PSIG (3 BAR), consult factory.
Viton ® and Kalrez® are Registered trademarks of DuPont Performance Elastomers. Metric conversions are based on US measurements and rounded to the nearest whole number.

VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2013

 Section 410 VIKING® HEAVY-DUTY ABRASIVE LIQUID PUMPS
Page 410.8 SERIES 4625
Issue H

DIMENSIONS
These dimensions are average and not for construction purposes. Certified prints on request.

For specifications, see page 410.2.

DIMENSIONS —
SERIES 4625
UNMOUNTED PUMPS
“F” AND “FH” SIZES

NOTE: Dimensions shown in inches, with millimeter

equivalent shown in parentheses.

For specifications, see page 410.2.

S W A-PIPE SIZE

DIMENSIONS — T

K
R N B

SERIES 4625
UNMOUNTED PUMPS U
B

“H” AND “M” SIZES

D C

V-KEYWAY
① Ports are suitable for use with 125# ANSI cast iron or 150#
F P J E E
ANSI steel companion flanges or flanged fittings. All others
M H L
tapped for standard pipe. G

MODEL NO. A B C D E F G H J K L M N O P R S T U V W
H4625 in 3.00 4.75 3.50 2.75 2.25 6.75 3.50 .47 1.50 3.38 5.19 1.19 .56 .62 10.44 13.25 1.62 .750 .19 x .09 2.88
AND 1½
HL4625 mm 76 121 89 70 57 171 89 12 38 86 132 30 14 16 265 337 41 19.05 4.76 x 2.38 73

K4625 in 5.12 8.00 5.50 4.00 2.75 9.25 4.00 .53 2.00 3.00 9.38 1.75 .62 .62 14.12 18.12 2.25 1.125 .25 x .12 5.12
AND 2
KK4625 mm 130 203 140 102 70 235 102 13 51 76 238 44 16 16 359 460 57 28.58 6.35 x 3.18 130

in 6.50 10.25 7.00 4.38 4.00 10.00 5.38 .53 2.00 3.38 9.12 1.75 .62 .62 15.62 19.62 2.25 1.125 .25 x .12 5.38
L4625 2
mm 165 260 178 111 102 254 137 13 51 86 232 44 16 16 397 498 57 28.58 6.35 x 3.18 137

in 7.19 10.25 7.00 4.38 4.00 10.00 5.38 .53 2.00 3.38 9.12 1.75 .62 .62 15.62 19.62 2.25 1.125 .25 x .12 5.38
LQ4625 ① 2½
mm 183 260 178 111 102 254 137 13 51 86 232 44 16 16 397 498 57 28.58 6.35 x 3.18 137

in 7.19 10.25 7.00 4.38 4.00 10.00 5.38 .53 2.00 3.38 9.12 2.25 .62 .62 15.62 20.12 2.25 1.125 .25 x .12 5.38
LL4625 ①3
mm 183 260 178 111 102 254 137 13 51 86 232 57 16 16 397 511 57 28.58 6.35 x 3.18 137

in 7.75 14.00 8.75 4.12 4.00 10.00 6.00 .69 4.38 6.62 11.12 3.00 .75 1.00 19.25 26.75 4.50 1.938 .50 x .25 8.19
Q4625 ①3
mm 197 356 222 105 102 254 152 18 111 168 282 76 19 25 489 679 114 49.22 12.70 x 6.35 208

in 9.50 17.25 10.00 5.00 6.00 12.00 8.50 .69 4.00 7.75 8.12 4.00 1.00 1.50 20.12 28.38 4.25 1.938 .50 x .25 8.50
M4625 ①4
mm 241 438 254 127 152 305 216 18 102 197 206 102 25 38 511 721 108 49.22 12.70 x 6.35 216

VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2013

VIKING® HEAVY-DUTY ABRASIVE LIQUID PUMPS Section 410

SERIES 4625 Page 410.9

Issue H

DIMENSIONS
These dimensions are average and not for construction purposes. Certified prints on request.

For specifications, see page 410.3.

DIMENSIONS—
SERIES 4625
(“R” DRIVE)
“H” AND “HL” SIZE PUMPS
“A” SIZE REDUCER UNITS
①

① With motor frames 182-T and smaller, use the (4) corner
base anchor holes. Motor frame 184-T covers up the lower
left corner anchor hole, so the hole 9” to right is used.
NOTE: Dimensions shown in inches, with millimeter
equivalent shown in parentheses.

For specifications, see page 410.3.

DIMENSIONS—
SERIES 4625
(“R” DRIVE)
“K” THROUGH “LL” SIZE
PUMPS
“B” SIZE REDUCER UNITS

MODEL
NUMBER A B C E F G J K L M N BASE
② K4625R in 5.12 9.50 4.00 14.25 48.00 1.38 .62 2.00 6.88 4.25
AND 2
KK4625R mm 130 241 102 362 1219 35 16 51 175 108

in 6.50 11.00 4.00 14.25 48.00 1.38 .62 2.38 7.12 4.62 NOTE: Motor rails 2” high are required on “L” through “LL”
L4625R 2 size units with 184-T or 4½” center height motors.
mm 165 2.79 102 362 1219 35 16 60 181 117
2-022-010
① Ports are suitable for use with 125# ANSI cast iron or 150#
in 7.19 11.00 4.00 14.25 48.00 1.38 .62 2.38 7.12 4.62 ANSI steel companion flanges or flanged fittings.
①
LQ4625R All others tapped for standard pipe.
2½ mm 183 279 102 362 1219 35 16 60 181 117 ② With motor frames 184-T and smaller, these units are
assembled on a shorter base with the following dimension
in 7.19 11.00 4.00 14.25 48.00 1.38 .62 2.38 7.62 4.62
① changes: (F = 16”, G = 39”, L = 3”, N = 5⅝”).
LL4625R
3 mm 183 279 102 362 1219 35 16 60 194 117 Motor rails 1⅞” high are required with 56, 143-T and 145-T
frame motors.

VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2013

 Section 410 VIKING® HEAVY-DUTY ABRASIVE LIQUID PUMPS
Page 410.10 SERIES 4625
Issue H

DIMENSIONS
These dimensions are average and not for construction purposes. Certified prints on request.

For specifications, see page 410.3.

DIMENSIONS —
SERIES 4625
(“R” DRIVE)
“KK” THROUGH “M” SIZE
PUMPS
“C” SIZE REDUCER UNITS
MODEL
NUMBER A B C E F G J K L M N BASE
in 5.12 13.75 6.00 21.00 49.00 1.50 .69 3.00 6.88 6.06
KK4625R 2 3-022-054
mm 130 349 152 533 1245 38 18 76 175 154
in 6.50 13.75 6.00 19.75 59.50 1.50 .69 0 7.12 5.75
L4625R 2
mm 165 349 152 502 1511 38 18 0 181 146
① in 7.19 13.75 6.00 19.75 59.50 1.50 .69 0 7.12 5.75
LQ4625R 2-022-008
2½ mm 183 349 152 502 1511 38 18 0 181 146
① in 7.19 13.75 6.00 19.75 59.50 1.50 .69 0 7.62 5.75
LL4625R
3 mm 183 349 152 502 1511 38 18 0 194 146
① in 7.75 14.75 6.00 19.75 59.50 1.50 .69 5.88 11.19 5.75
Q4625R
4 mm 197 375 152 502 1511 38 18 73 284 146
3-023-011
① Ports are suitable for use with 125# ANSI cast iron or 150# ① in 9.50 16.00 6.00 19.75 59.50 1.50 .69 6.50 12.50 5.75
ANSI steel companion flanges or flanged fittings. All others M4625R
4 mm 241 406 152 502 1511 38 18 89 318 146
tapped for standard pipe.

For specifications, see page 410.6.

DIMENSIONS —
SERIES 4625
(“D” DRIVE)
“H” THROUGH “M” SIZE
PUMPS
① Ports are suitable for use with 125# ANSI cast iron or 150#
ANSI steel companion flanges or flanged fittings. All others
tapped for standard pipe.
MODEL ②
② Varies with gearmotor used. NUMBER A B D E F G H K L M N S BASE
NOTE: Pump models “K” through “LL” are normally placed H4625D in 3.00 2.94 25.00 1.00 1.50 .56 .56 4.06 9.00 4.50
on formed steel bases as shown with outside dimensions 4” AND
1½
x 18¾” x 41¾”. Pump models “Q” and “M” are normally
HL4625D mm 76 75 635 25 38 14 14 103 229 114
placed on formed steel bases as shown with outside K4625D in 5.12 4.00 39.00 1.38 1.38 .62 3.00 6.88 16.00 8.00
dimensions 6” x 22¾” x 62½”.
AND 2
KK4625D mm 130 102 991 35 35 16 76 175 406 203
Units are placed on stock formed steel bases if possible, in 6.50 4.00 39.00 1.38 1.38 .62 3.38 7.12 16.00 8.00
depending on the width of the gearmotor and total length of L4625D 2
mm 165 102 991 35 35 16 86 181 406 203
the unit figured from the back of the motor foot to the end of
the pump foot. ① in 7.19 4.00 39.00 1.38 1.38 .62 3.38 7.12 16.00 8.00
LQ4625D STEEL
For foundation space estimates, the following base 2½ mm 183 102 991 35 35 16 86 181 406 203
dimensions can be used: ① in 7.19 4.00 39.00 1.38 1.38 .62 3.38 7.62 16.00 8.00
LL4625D
2¹⁵⁄₁₆” x 12” x 27” (Four ⁹⁄₁₆” holes 9” x 25” centers) 3 mm 183 102 991 35 35 16 86 194 406 203
4” x 18¾” x 41¾” (Four ⅝” holes 16” x 39” centers)
4” x 17” x 50¾” (Four ⅝” holes 14¼” x 48” centers) ① in 7.75 6.00 59.50 1.50 1.50 .69 5.75 11.19 19.75 9.88
Q4625D
6” x 22¾” x 62½” (Four ¹¹⁄₁₆” holes 19¾” x 59½” centers) 3 mm 197 152 1511 38 38 18 146 284 502 251
6” x 24” x 52” (Four ¹³⁄₁₆” holes 21” x 49” centers) ① in 9.50 6.00 59.50 1.50 1.50 .69 6.88 12.50 19.75 9.88
6” x 30” x 52” (Four ¹³⁄₁₆” holes 27” x 49” centers) M4625D
6” x 32” x 62” (Four ¹³⁄₁₆” holes 29” x 59” centers) 1½ mm 241 152 1511 38 38 18 175 318 502 251

VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2013

VIKING® HEAVY-DUTY ABRASIVE LIQUID PUMPS Section 410

SERIES 4625 Page 410.11

Issue H

DIMENSIONS
These dimensions are average and not for construction purposes. Certified prints on request.

For specifications, see page 410.7.

DIMENSIONS —
SERIES 4625
(“V” DRIVE)
“H” THROUGH “Q” SIZE
PUMPS
V-BELT DRIVE UNITS

MODEL
NUMBER A B C E F G J K L M N BASE
② in 3.00 9.25 1.75 14.75 23.75 .75 .50 4.88 4.06 4.25
H4625V
AND 1½ 3-027-001
HL4625V mm 76 235 44 375 603 19 13 124 103 108
③ in 5.12 13.81 3.25 17.00 28.75 1.00 .50 2.50 6.88 5.25
K4625V 2
AND
KK4625V mm 130 351 83 432 730 25 13 64 175 133

in 6.50 15.31 3.25 17.00 28.75 1.00 .50 2.25 7.12 5.25
③ 2 3-027-005
L4625V
mm 165 389 83 432 730 25 13 57 181 133

① in 7.19 15.31 3.25 17.00 28.75 1.00 .50 2.25 7.12 5.25
③
LQ4625V 2½ mm 183 389 83 432 730 25 13 57 181 133
① Ports are suitable for use with 125# ANSI cast iron or 150#
① in 7.19 15.31 3.25 17.00 28.75 1.00 .50 2.25 7.62 5.25 ANSI steel companion flanges or flanged fittings. All others
③ tapped for standard pipe.
LL4625V 3 mm 183 389 83 432 730 25 13 57 194 133
3-028-021 ② Base dimensions correct for all motors.
① in 7.75 21.25 6.00 21.00 49.00 1.50 .81 2.75 11.19 8.50 ③ Base dimensions correct through frame 215-T motors and
Q4625V
3 19” OD sheaves. Larger motors and or 25” OD sheaves
mm 197 540 152 533 1245 38 21 70 284 216
require larger base.

VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2013

 Section 410 VIKING® HEAVY-DUTY ABRASIVE LIQUID PUMPS
Page 410.12 SERIES 4625
Issue H

Performance Curve Notes

Printed performance curves are not available.

Performance curves can be electronically generated with the Viking Pump Selector Program.
This program can be located on www.vikingpump.com for the general public.

For authorized distributors, this program can be found listed under the “Products” tab at
www.idexconnect.com. Security passwords are required to access IDEXconnect.

INLET CONDITIONS: The performance curves show FOR VISCOSITIES ABOVE 750 SSU (NPSHR data not
“Based on 10 (or 15) In.-Hg.” which is Viking’s standard available): The performance curves are based on 15
test condition. This is not the maximum vacuum In.-Hg.” While vacuums up to 20 In.-Hg. will not generally
capability of the pump. result in any loss of capacity, it is recommended that the
suction line size and possibly the pump port size be
NPSH (Net Positive Suction Head): The NPSHR (Net increased to hold the expected vacuum to 15 In.-Hg.
Positive Suction Head – Required by the pump) is given or less. Vacuum above 20 In.-Hg. should be avoided.
in the table below and applies for viscosities through 750 (Refer to Viking’s General Catalog, Engineering
SSU. NPSHA (Net Positive Suction Head – Available in Section 510, and Engineering Service Bulletin ESB-56
the system) must be greater than the NPSHR. for information helpful in determining suction line size).
NPSHR – FEET OF LIQUID (SP. GR. 1.0),
Viscosities to 750 SSU THIN LIQUIDS: Pump capacity when handling 28
SSU liquids (solvents, etc.) is shown on the 38 SSU
Pump Pump Speed, RPM performance curve found in the pump selector program
Size 125 280 420 520 640 780 870 on www.vikingpump.com as a broken line. Pressure
shown on broken line is the maximum recommended for
F, FH 1.0 1.3 1.6 1.7 1.8 1.9 2.0
28 SSU liquids. It is shown as a reference for flushing
H, HL 1.3 1.8 2.1 2.4 2.8 — —
cycles only; pumps should not be used for continuous
Pump Pump Speed, RPM duty with solvents. Horsepower required for 28 SSU is
Size 84 100 125 155 190 230 280 the same as 38 SSU at any given pressure.
K, KK 1.5 1.6 1.7 1.8 1.9 2.1 2.3
MECHANICAL EFFICIENCY: The Mechanical
L, LQ, LL 1.6 1.7 1.8 2.0 2.2 2.5 —
Efficiency (expressed in percent) can be calculated
Q 1.7 1.9 2.1 2.3 2.7 — —
using the following formula:
M 1.9 2.1 2.3 2.8 — — — (Differential Pressure, PSI) (Capacity, GPM) (100)
For a complete explanation of NPSH, see Application Mechanical Efficiency =
(Horsepower, BHP) (1715)
Data Sheet AD-19.

METRIC CONVERSION: The following table has been

compiled for conversion to metric values.
Vacuum Pressure Capacity
In.-Hg. kPa* PSI kPa* GPM LPM
(Inches Mercury) (Kilopascal) (lbf / in.2) (Kilopascal) (Gallons / Minute) (Litre / Minute)
1 3.4 1 6.9 1 3.8
5 17 25 172 0.26 1
10 34 50 345 — —
15 51 100 690 — —
20 68 150 1034 — —
25 85 200 1379 — —
— — 250 1724 — —
* 100 kPa = 1 bar
VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2013