ESTIMATE FOR CONSTRUCTION OF

2 ROOMS
CIVIL WORK
BELOW FINISH FLOOR LEVEL
Sr. Ref. Of Description of Item Nos. L B H Unit Quantity
No. HSR
Item
1 4.14.1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation
trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and
ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus
excavated soil as directed, within a lead of 50 m. (HSR 4.14.1)

F-1 3 8.00 7.00 5.00 Cft 840.00

F-2 3 9.00 8.00 5.00 Cft 1080.00
F-3 3 5.00 5.00 5.00 Cft 375.00
For Toe Walls
Sides 2 16.00 2.50 5.00 Cft 400.00
Front & Rear 2 20.00 2.50 5.00 Cft 500.00
For Plinth Protaction
Outer Periphery of Building 1 120.00 1.50 2.00 Cft 360.00
Total 3555.00 100.68 Cum

2 4.32 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in
layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering,
lead up to 50 m and lift up to 1.5 m. (HSR 4.32)
Taking 60% Qty. of excavation of earth 100.68 x 60% 60.41 Cum
work i.e
3 4.33 Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a
lead of 1 km also including ramming and watering of the earth in layers not exceeding 20 cm in
trenches, plinth, sides of foundation etc. complete.(HSR 4.33)
1 900.00 1.50 Cft 1350.00
Total 1350.00 38.23 Cum

4 6.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering
and shuttering - All work below plinth level and up to Floor IV level: 1:5:10 (1 cement : 5 fine sand :
10 graded stone aggregate 40 mm nominal size)(HSR 6.1.8)
Under Plinth Protection 1 480.00 0.25 Cft 120.00
Total 120.00 3.40 Cum

5 6.1.6 Providing and laying in position cement concrete of specified grade excluding the cost of centering
and shuttering - All work below plinth level and up to Floor IV level: 1:4:8 (1 cement : 4 fine
sand(Zone III) : 8 graded cum stone aggregate 40 mm nominal size)(HSR 6.1.6)
F-1 3 7.50 6.50 0.50 Cft 73.13
F-2 3 8.50 7.50 0.50 Cft 95.63
F-3 3 4.50 4.50 0.50 Cft 30.38
For Toe Walls
Sides 2 16.00 2.00 0.50 Cft 32.00
Front & Rear 2 20.00 2.00 0.50 Cft 40.00
Total 271.13 7.68 Cum

1
CIVIL WORK
6 6.25.1 Providing and laying in position mechine batched and machine mixed design mix M-25 grade
cement concrete for reinforced cement concrete work, using cement content as per approved design
mix, including pumping of concrete to site of lying but excluding the cost of centering, shuttering,
finishing and reinforment, including the admixtures in recommended proportions as per IS: 9103 to
accelerate, retard setting of concrete, improve workability without impairing strength and durability
as per direction of Engineer-in-chrage in foundation and plinth.(note : cement content considered in
this item is 330kg/cum. less cement used as per design mix is recoverable. however no extra payment
shall be made if excess cement is used as per design mix.) All works up to plinth level. (HSR 6.25.1)

(From Foundation to FFL)

COLUMNS
C1,C2 6 1.00 2.00 3.00 Cft 36.00
C3 3 0.75 0.75 3.00 Cft 5.06
PLINTH BEAMS
PB1 3 32.75 1.00 1.50 Cft 147.38
PB2 3 28.00 0.75 1.00 Cft 63.00

FOOTINGS
F-1
(Rectanglar Portion) 3 7.00 6.00 0.75 Cft 94.50
Taper Slab Cft 56.70
F-2
(Rectanglar Portion) 3 8.00 7.00 0.75 Cft 126.00
Taper Slab Cft 75.60
F-3
(Rectanglar Portion) 3 4.00 4.00 0.75 Cft 36.00
Taper Slab Cft 21.60
Total 661.84 18.76 Cum

7 6.30.1 Centering and shuttering including strutting, propping etc. and removal of form for Foundations,
footings, bases for columns (HSR 6.30.1)

For Footings
F1 6 7.00 6.00 0.75 Sft 58.50
F2 6 8.00 7.00 0.75 Sft 67.50
F3 6 4.00 4.00 0.75 Sft 36.00
Total 162.00 15.06 Sqm

8 6.30.5 Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams,
plinth beams, girders, bressumers and cantilevers. (HSR 6.30.5)

For Plinth Beams

PB1 3 32.50 1.00 Sft 97.50
6 32.50 1.50 Sft 292.50
PB2 3 28.00 0.75 Sft 63.00
6 28.00 1.00 Sft 168.00
Total 621.00 57.71 Sqm

9 6.30.6 Centering and shuttering including strutting, propping etc. and removal of form for Columns,
Pillars, Piers, Abutments, Posts and Struts (HSR 6.30.6)

For Columns
C1,C2 12 1.00 3.00 Sft 36.00

2
CIVIL WORK
12 2.00 3.00 Sft 72.00
C3 6 0.75 3.00 Sft 13.50
6 0.75 3.00 Sft 13.50
Total 135.00 12.55 Sqm

11 6.12.2 20 mm thick cement plaster damp-proof course 1:3 with 2 coats of bitumen at 1.65 kg. per sqm, laid
hot and sanded:(horizontal)(HSR 6.12.2)

ON INTERNAL/EXTERNAL WALLS
3 32.75 1.00 Sft 98.25
3 28.00 0.75 Sft 63.00
Total 161.25 14.97 Sqm

12 6.33.6 Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including
straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer
bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect for all
heights/depths/storeys/basements etc. Note:- Reinforcement shall be measured in length including
hooks, if any, separately for different diameters as actually used in work , excluding overlaps.
Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel
wire or other methods of binding and placing shall not be measured and cost of these items shall be
deemed to be included in the rates for reinforcement. Thermo-Mechanically Treated bars of grade
Fe-500D or more. (HSR 6.33.6).

Qty. of HSR No.6.25.1(Sr.no. 6) 18.76 @ 220 Kg. 4127.10

Total 4127.10 Kg

13 7.21.2 Brick work with common burnt clay non-modular bricks of class designation 7.5 in foundation and
plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)(HSR 7.21.2)

In Toe Walls
1 120.00 2.25 0.50 Cft 135.00
1 119.63 1.88 0.50 Cft 112.15
1 119.25 1.50 0.50 Cft 89.44
1 118.88 1.13 0.50 Cft 66.87
1 118.50 0.75 2.50 Cft 222.19
In Plinth Protection 1 120.00 0.75 1.50 Cft 135.00

Total 760.64 21.54 Cum

ABOVE FINISH FLOOR LEVEL

1 6.12.1 20 mm thick cement plaster damp-proof course 1 :3 with 2 coats of bitumen at 1.65 kg. per sqm, laid
hot and sanded: vertical (6.12.1)

On Outer Walls
1 120.00 2.50 Sft 300.00
Total 300.00 27.88 Sqm

3
CIVIL WORK
2 6.25.2 Providing and laying in position mechine batched and machine mixed design mix M-25 grade
+ 6.4 cement concrete for reinforced cement concrete work, using cement content as per approved design
mix, including pumping of concrete to site of lying but excluding the cost of centering, shuttering,
finishing and reinforment, including the admixtures in recommended proportions as per IS: 9103 to
accelerate, retard setting of concrete, improve workability without impairing strength and durability
as per direction of Engineer-in-chrage in foundation and plinth.(note : cement content considered in
this item is 330kg/cum. less cement used as per design mix is recoverable. however no extra payment
shall be made if excess cement is used as per design mix.) All works above plinth level. Extra for
concrete work in superstructure above floor IV level for each four floors or part thereof.(HSR 6.25.2
+6.4)

First Storey
COLUMNS
C1,C2 6 1.00 2.00 11.00 Cft 132.00
C3 3 0.75 0.75 11.00 Cft 18.56
Slab Beams
FB1 3 32.50 1.00 1.50 Cft 146.25
FB2 1 28.00 0.75 1.00 Cft 21.00
FB3 1 28.00 0.75 1.00 Cft 21.00
FB4 1 28.00 0.75 0.75 Cft 15.75
Lintel Beams 3 28.00 0.75 0.75 Cft 47.25
First Storey Slab 1 910.00 0.50 Cft 455.00
Total 856.81 24.27 Cum

Second Storey
COLUMNS
C1,C2 6 1.00 2.00 11.00 Cft 132.00
C3 3 0.75 0.75 11.00 Cft 18.56
Slab Beams
FB1 3 32.50 1.00 1.50 Cft 146.25
FB2 1 28.00 0.75 1.00 Cft 21.00
FB3 1 28.00 0.75 1.00 Cft 21.00
FB4 1 28.00 0.75 0.75 Cft 15.75
Lintel Beams 3 28.00 0.75 0.75 Cft 47.25
First Storey Slab 1 910.00 0.50 Cft 455.00
Total 856.81 24.27 Cum
Total Qty. 48.54 Cum

3 6.30.3 Centering and shuttering including strutting, propping etc. and removal of form for Suspended
floors, roofs, landings, balconies and access platform (HSR 6.30.3)

First Storey
ROOMS 2 24.50 12.88 Sft 630.88
CORRIDOR 1 6.00 26.50 Sft 159.00
Total 789.88 73.41 Sqm

Second Storey
ROOMS 2 24.50 12.88 Sft 630.88
CORRIDOR 1 6.00 26.50 Sft 159.00
Total 789.88 73.41 Sqm
4 6.30.5 Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams,
plinth beams, girders, bressumers and cantilevers. (HSR 6.30.5)

First Storey Beams

4
CIVIL WORK
FB1 3 32.50 1.00 Sft 97.50
6 32.50 1.50 Sft 292.50
FB2 1 28.00 0.75 Sft 21.00
2 28.00 1.00 Sft 56.00
FB3 1 28.00 0.75 Sft 21.00
1 28.00 1.00 Sft 28.00
FB4 1 28.00 0.75 Sft 21.00
2 28.00 0.75 Sft 42.00
Total 579.00 53.81 Sqm
Second Storey Beams
SB1 3 32.50 1.00 Sft 97.50
6 32.50 1.50 Sft 292.50
SB2 1 28.00 0.75 Sft 21.00
2 28.00 1.00 Sft 56.00
SB3 1 28.00 0.75 Sft 21.00
1 28.00 1.00 Sft 28.00
SB4 1 28.00 0.75 Sft 21.00
2 28.00 0.75 Sft 42.00
Total 579.00 53.81 Sqm
5 6.30.6 Centering and shuttering including strutting, propping etc. and removal of form for Columns,
Pillars, Piers, Abutments, Posts and Struts (HSR 6.30.6)
First Storey Columns
C1,C2 12 1.00 12.00 Sft 144.00
12 2.00 12.00 Sft 288.00
C3 6 0.75 12.00 Sft 54.00
6 0.75 12.00 Sft 54.00
Total 540.00 50.19 Sqm

Second Storey Columns

C1,C2 12 1.00 12.00 Sft 144.00
12 2.00 12.00 Sft 288.00
C3 6 0.75 12.00 Sft 54.00
6 0.75 12.00 Sft 54.00
Total 540.00 50.19 Sqm

6 6.33.6 Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including
straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer
bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect for all
heights/depths/storeys/basements etc. Note:- Reinforcement shall be measured in length including
hooks, if any, separately for different diameters as actually used in work , excluding overlaps.
Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel
wire or other methods of binding and placing shall not be measured and cost of these items shall be
deemed to be included in the rates for reinforcement. Thermo-Mechanically Treated bars of grade
Fe-500D or more. (HSR 6.33.6).
Qty. of HSR No.10.73(Sr No. 2) 48.54 @ 220 Kg. 10678.80
Total 10678.80 Kg

5
CIVIL WORK
7 7.22.2 Brick work with common burnt clay non-modular bricks of class designation 7.5 in foundation and
above plinth level up to level IV level in all shapes and sizes in: Cement mortar 1:6 (1 cement : 6
coarse sand) Note : For item 7 .22, 7 .23, 7 .24, extra rate @ 1 % for each three additional floor
above floor iv level shall be added on the rates of item 7.20 and 7.21 (HSR 7.22.2)

First Storey
Walls 3 24.50 0.75 10.50 Cft 578.81
6 12.88 0.75 11.00 Cft 637.31
Deductions
D1 -2 3.00 0.75 6.75 Cft -30.38
D2 -1 2.50 0.75 6.75 Cft -12.66
W1 -2 6.00 0.75 4.00 Cft -36.00
W2 -2 4.00 0.75 4.00 Cft -24.00
Total 1113.09 31.52 Cum

Second Storey
Walls 3 24.50 0.75 10.50 Cft 578.81
6 12.88 0.75 11.00 Cft 637.31
Deductions
D1 -2 3.00 0.75 6.75 Cft -30.38
D2 -1 2.50 0.75 6.75 Cft -12.66
W1 -2 6.00 0.75 4.00 Cft -36.00
W2 -2 4.00 0.75 4.00 Cft -24.00
Total 1113.09 31.52 Cum

8 9.17.1 Providing gola 75x75 mm in cement concrete 1: 2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10
mm and down gauge), including finishing with cement mortar 1 :3 (1 cement : 3 fine sand) as per
standardStorey
THIRD design : In 75x75 mm deep chase (HSR
1 9.17.1).
120.00 Rft 120.00
Total 120.00 36.59 Rmt

9 9.18 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1 :2:4 (1
cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m
x 400 micron, finished with 12 mm cement plaster 1 :3 (1 cement : 3 coarse sand) and a coat of neat
cement, rounding the edges and making and finishing the outlet complete. (bottom and top)(HSR
9.18)

4 Nos. 4
Total 4

10 9.55.5 Supplying and fixing in position 60 cm long G.I. pipe class 'B' spouts in chajjas and cantilevers 50
mm internal dia (HSR 9.55.5)

4 3.00 Rft 12.00

Total 12.00 3.66 Rmt

11 9.57.2 Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592
Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal
expansion, (i) Single socketed pipes. 110mm [HSR 9.57.2].
4 25.00 Rft 100.00
Total 100.00 30.49 Rmt

6
CIVIL WORK
12 9.58.3.2 Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised
Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring
conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee with door
110x110x110mm[HSR 9.58.3.2].

8 Nos. 8.00
Total 8.00 Nos.

13 10.1.1 Providing and laying of base course of floors consisting of 100 mm thick cement 1 :8: 16 and 100 mm
sand or stone filling.(HSR 10.1)
First Storey
Rooms 2 24.50 12.88 Sft 630.88
Corriodor 1 26.50 6.00 Sft 159.00
Total 789.88 73.41 Sqm

14 10.4 Providing and laying of screed of 50 mm thick cement concrete 1 :8:16 to sqm be laid below the
topping. (HSR 10.4)

Second Storey
Rooms 2 24.50 12.88 Sft 630.88
Corriodor 1 26.50 6.00 Sft 159.00
Total 789.88 73.41 Sqm

15 10.7 Providing and laying of conglomerate floor 50mm thick cement concrete topping 1 :2:4(HSR 10.7)

For Plinth Protection

Around the Building 1 120.00 4.00 Sft 480.00
Total 480.00 44.61 Sqm

16 10.37.1 Providing and fixing of Kota stone slab flooring over 20 mm (average) thick base laid over and
jointed with grey cement slurry mixed with pigment to match the shade of the slab, including
rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement : 4 coarse sand) : 25mm
thick (HSR 10.37.1)

First Storey
Rooms 1 24.50 12.88 Sft 315.44
Corridor 1 26.50 6.00 Sft 159.00
Total 474.44 44.09 Sqm
Second Storey
Rooms 1 24.50 12.88 Sft 315.44
Corridor 1 26.50 6.00 Sft 159.00
Total 474.44 44.09 Sqm

17 10.38 Providing and fixing of Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars
laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey
cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing
complete.(HSR 10.38)

First Storey
Rooms 2 24.50 0.33 Sft 16.17
2 12.88 0.33 Sft 8.50
Corridor 2 26.50 0.33 Sft 17.49

7
CIVIL WORK
2 6.00 0.33 Sft 3.96

Deductions(Doors) -6 3.00 0.33 Sft -5.94

Total 40.18 3.73 Sqm
Second Storey
Rooms 2 24.50 0.33 Sft 16.17
2 12.88 0.33 Sft 8.50
Corridor 2 26.50 0.33 Sft 17.49
2 6.00 0.33 Sft 3.96
Deductions(Doors) -6 3.00 0.33 Sft -5.94
Total 40.18 3.73 Sqm

18 10.86 Providing and fixing glass strips, 5.5 mm thick 40mm wide in floors (HSR 10.86)
In Plinth Protection
40.00 4.00 Rft 160.00
Total 160.00 48.78 Rmt

19 11.5.3 12 mm cement plaster of mix : 1 :4 (1 cement: 4 fine sand) (HSR : 11.5.3)

First Storey
Walls 6 24.50 11.50 Sft 1690.50
12 12.88 11.50 Sft 1776.75
Deductions
D1 -2 3.00 14.00 6.75 Sft -189.00
D2 -1 2.50 8.50 6.75 Sft -57.38
W1 -2 6.00 4.50 6.00 Sft -54.00
W2 -2 4.00 3.00 4.00 Sft -24.00
Total 3142.88 292.09 Sqm

Second Storey
Walls 6 24.50 11.50 Sft 1690.50
12 12.88 11.50 Sft 1776.75
Deductions
D1 -2 3.00 14.00 6.75 Sft -189.00
D2 -1 2.50 8.50 6.75 Sft -57.38
W1 -2 6.00 4.50 6.00 Sft -54.00
W2 -2 4.00 3.00 4.00 Sft -24.00
Total 3142.88 292.09 Sqm
G. Total 584.18 Sqm

20 11.57 Providing & laying average 6mm thick POP Coating on walls, Ceiling, beams and lintels etc.
complete in all respects as approved by the Engineer-In- Charge.(HSR 11.57)

First Storey
Rooms 1 24.50 12.88 Sft 315.44
Corridor 1 26.50 6.00 Sft 159.00
Total 474.44 44.09 Sqm

Second Storey
Rooms 1 24.50 12.88 Sft 315.44
Corridor 1 26.50 6.00 Sft 159.00
Total 474.44 44.09 Sqm

8
CIVIL WORK
21 11.58 Providing and applying two coats white cement based putty of approved brand and manufacturer,
over plastered surface and grinding the surface smooth with sand paper to get en even and smooth
finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete.
(HSR 11.58)

Qty. of 12 mm Plaster Qty. of Item No. 15.7 584.18 Sqm

Total 584.18 Sqm

22 11.64.1 Distempering with oil bound washable distemper of approved brand and manufacture to give an
even shade: New work (two or more coats) over and including water thinnable priming coat with
cement primer(11.64.1)
First Storey
Walls 6 24.50 11.50 Sft 1690.50
12 12.88 11.50 Sft 1776.75
Deductions
D1 -2 3.00 14.00 6.75 Sft -189.00
D2 -1 2.50 8.50 6.75 Sft -57.38
W1 -2 6.00 4.50 6.00 Sft -54.00
W2 -2 4.00 3.00 4.00 Sft -24.00
On Ceiling
Rooms 1 24.50 12.88 Sft 315.44
Corridor 1 26.50 6.00 Sft 159.00
Total 3617.31 336.18 Sqm

Second Storey
Walls 6 24.50 11.50 Sft 1690.50
12 12.88 11.50 Sft 1776.75
Deductions
D1 -2 3.00 14.00 6.75 Sft -189.00
D2 -1 2.50 8.50 6.75 Sft -57.38
W1 -2 6.00 4.50 6.00 Sft -54.00
W2 -2 4.00 3.00 4.00 Sft -24.00
On Ceiling
Rooms 1 24.50 12.88 Sft 315.44
Corridor 1 26.50 6.00 Sft 159.00
Total 3617.31 336.18 Sqm
G. Total 672.36 Sqm

23 11.68.3 Applying priming coat With ready mixed red oxide zinc chroate primer of approved brand and
manufacture on steel galvanised iron/ steel works.(HSR 11.68.3)
Windows Grills
W1 2 6.00 4.00 Sft 48.00
W2 2 8.00 4.00 Sft 64.00
Total 112.00 10.41 Sqm

24 11.76 Preparation of ply wood surface for painting inlcuding sand papering the surface and applying
filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti
including finishing the surface to required finish complete. (HSR 11.76)
Qty. of Item No. 12.10.2.2 7.50 x 1.00 7.50 Sqm
Qty. of Item No. 12.19.2.2.2 7.50 x 1.60 12.01 Sqm
Qty. of Item No. 12.37.1 11.61 x 2.40 27.85 Sqm
Total 47.36 Sqm

9
CIVIL WORK
25 11.77 Applying pink primer or aluminium priming coat on wood work including preparation of surface,
knotting and stopping etc. (HSR 11.77)

Qty. of Item No. 12.10.2.2 7.50 x 1.00 7.50 Sqm

Qty. of Item No. 12.19.2.2.2 7.50 x 1.60 12.01 Sqm
Qty. of Item No. 12.37.1 11.61 x 2.40 27.85 Sqm
Total 47.36 Sqm

26 11.78 Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood
work or metallic or plastered or concrete surfaces to give an even shade.(HSR 11.78)

Qty. of Item No. 12.10.2.2 7.50 x 1.00 7.50 Sqm

Qty. of Item No. 12.19.2.2.2 7.50 x 1.60 12.01 Sqm
Qty. of Item No. 12.37.1 11.61 x 2.40 27.85 Sqm
Total 47.36 Sqm

27 11.82.1 Painting the wooden/metal surface with synthetic enamel paint of approved brand and manufacture
to give an even shade Two or more coats on new work (HSR 11.82.1)

Qty. of Item No. 11.68.3 10.41 x 1.00 Total 10.41 Sqm

28 11.96.1 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required
shade:New work (Two or more coats applied @ 1.43 litre/10 sqm over and including priming coat of
exterior primer applied @ 2.20 kg/10 sqm) (HSR 11.96.1)

First Storey
Walls 6 24.50 11.50 Sft 1690.50
12 12.88 11.50 Sft 1776.75
Deductions
D1 -2 3.00 14.00 6.75 Sft -189.00

D2 -1 2.50 8.50 6.75 Sft -57.38

W1 -2 6.00 4.50 6.00 Sft -54.00
W2 -2 4.00 3.00 4.00 Sft -24.00
On Ceiling
Rooms 1 24.50 12.88 Sft 315.44
Corridor 1 26.50 6.00 Sft 159.00
Total 3617.31 336.18 Sqm

Second Storey
Walls 6 24.50 11.50 Sft 1690.50
12 12.88 11.50 Sft 1776.75
Deductions
D1 -2 3.00 14.00 6.75 Sft -189.00
D2 -1 2.50 8.50 6.75 Sft -57.38
W1 -2 6.00 4.50 6.00 Sft -54.00
W2 -2 4.00 3.00 4.00 Sft -24.00
On Ceiling
Rooms 1 24.50 12.88 Sft 315.44
Corridor 1 26.50 6.00 Sft 159.00
Total 3617.31 336.18 Sqm

10
CIVIL WORK
G. Total 672.36 Sqm

29 12.10.2.2 Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick
float glass panes, including ISi marked M.S. pressed butt hinges bright finished of required size with
necessary screws. Kiln seasoned and chemically treated Hollock wood.(HSR 12.10.2.2)

W1 4 3.00 3.67 Sft 44.04

W2 4 2.50 3.67 Sft 36.70
Total 80.7 7.50 Sqm

30 12.19.2.2. Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of
2 aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory
windows with hinges and necessary screws:With ISi marked stainless steel butt hinges of required
size. Kiln seasoned and chemically treated Hollock wood.(HSR 12.19.2.2.2)

W1 4 3.00 3.67 Sft 44.04

W2 4 2.50 3.67 Sft 36.70
Total 80.7 7.50 Sqm

31 12.37.1 Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) non-decorative
type, core of block board construction with frame of 1st class hard wood and well matched
commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of
shutters : 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws. (HSR
12.37.1)

35 mm
D1 3 4.50 6.75 Sft 91.13
D2 2 2.50 6.75 Sft 33.75
Total 124.9 11.61 Sqm

32 12.50.1 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square
or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel
windows by welding (HSR 12.50.1).

Windows Grills
W1 4 3.00 3.67 Sft 44.04
W2 4 2.50 3.67 Sft 36.70
Total 80.74
80.74 Sft. @ 3.00 Kg/sft 242.22 Kg

33 12.98 Providing and fixing aluminium sliding door bolts, ISi marked anodised (anodic coating not less than
grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws
etc. complete(HSR 12.98)

(12.98.2) Size 250 mm x 16 mm

D1 3 Nos. Nos. 3.00
D2 2 Nos. Nos. 2.00
Total 5.00 5.00 Each

34 12.99 Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than
grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary
screws etc. complete (HSR 12.99)

11
CIVIL WORK
12.99.4 Windows (150x10mm)
Glazed Shutters
W1 4 1.00 Each 4.00
W2 4 1.00 Each 4.00
Wire Gauge Shutters
W1 4 1.00 Each 4.00
W2 4 1.00 Each 4.00
Total 16.00 16.0 Each
12.99.2 Doors
D1 3 1.00 Each 3.00
D2 2 1.00 Each 2.00
Total 5.00 5.00 Each

35 12.102 Providing and fixing aluminium handles, ISi marked, anodised (anodic coating not less than grade
AC 1 O as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc.
complete(HSR 12.102)

12.102.2 Windows (100mm)

Glazed Shutters
W1 4 1.00 Each 4.00
W2 4 1.00 Each 4.00
Wire Gauge Shutters
W1 4 1.00 Each 4.00
W2 4 1.00 Each 4.00
Total 16.00 16.0 Each
12.102.1 Doors (125mm)
D1 3 1.00 Each 3.00
D2 2 1.00 Each 2.00
Total 5.00 5.00 Each

36 13.21 Supply & fixing Windows frames (Chowkhats) including mullions consisting frame fabricated from
sheet roll formed out of 1.2mm thick galvanized sheet as per IS:277 (Base steel as per IS 513) with
zinc of 120 gm/sqm & Powder coated with pure Polyester powder up to 50 microns (as per approved
colour), 3 Nos. 100mm butt - hinges 2mm thick, 6 Nos. 1.2mm thick CRCA electroplated stiffner, 6
Nos. M.S hold fast with split and tail welded to stiffner plate 200mm long, receiver for aldrop, weld
less corner assembly with brackets & screws, M.S tie rod 50mm x 25mm to be fixed at bottom
finished with powder coated total thickness of coating 0.6mm of approved shade, fixed in position
including the cost of cement concrete for 1 :2:4 for fixing lugs complete in all respects as per
drawing, design, specification & entire satisfaction of Engineer-in-charge.(HSR 13.21)

(13.21.1) door and window frame Size of 80 mm x 50 mm with 37 mm wide single rebate for 35mm door
shutter(13.21.1)

D1 3 2.00 7.00 Rft 42.00

3 1.00 4.50 Rft 13.50
D2 2 2.00 7.00 Rft 28.00
2 1.00 3.00 Rft 6.00
Total 89.50 27.29 Rmt

(13.21.2) door and window frame size 125 mm X 60 mm with 37 mm wide double rebate for 35mm door
shutter(13.21.2)

W1 4 2.00 6.00 Rft 48.00

4 4.00 4.00 Rft 64.00

12
CIVIL WORK
W2 4 2.00 4.00 Rft 32.00
4 4.00 4.00 Rft 64.00
Total 208.00 63.4 Rmt

37 28.43 Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar
refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped
surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1 :4 (1 cement : 4 coarse
sand) and grouting the joints with mix of white cement & marble powder in ratio of 1: 1, including
rubbing and polishing of the surface up to 3 cuts complete, including
providing skirting up to 150 mm height along the parapet walls in the same manner. (HSR 28.43).

Third Storey
1 910.00 Sft 910.00
Total 910.00 84.57 Sqm

13