TECHNICAL DATA SHEET TRUSPREAD DRY

SILO MORTAR

Ver Jan 2021

TECHNICAL
INFORMATION
TRUSPREAD DRY SILO MORTARS
Product Data Sheet No. 100/02

INTRODUCTION PHYSICAL PROPERTIES

Tarmac Truspread Dry Silo Mortars are a range of
factory produced mortars, manufactured under COMPOSITION AND STRENGTH
computer controlled conditions. The constituents are The mix proportions of Tarmac Truspread Dry Silo
dried fine aggregate (sand), cementitious materials Mortar conform with the values specified in the
and admixtures, together with pigments, if required. following table when tested by the methods
Tarmac Truspread Dry Silo Mortar is delivered direct prescribed in BS EN 1015 and BS 4551.
to site in state- of-the art silos, each complete with an
integral mixing unit. Once power and water have DENSITY
been connected, mortar can be produced at a touch
of a button. Alternatively, this can be supplied in
water resistant bulk bags, ready mixed – just add Typical test results Density kg/m2
water and mix to the required consistency. The mix
consistency can easily be adjusted by the site Fresh wet 1700 – 1900
operative in order to cater for the many varied types Set and air dried 1550 - 1750
of masonry units, from dense concrete blocks to high
suction bricks (in summer/ extreme conditions,
consider the use of Hydrocure & Hyrdocure+ refer to PERFORMANCE
Product Data Sheet No.100/03), as well as to suit Tarmac Truspread Dry Silo Mortars are based on
prevailing weather conditions. performance. We would recommend you consider the
following strength designations when specifying
PRODUCT CONFORMITY mortar mixes. Results are based on prisms made
Tarmac Truspread Dry Silo Mortars are from typical production material cured and tested in
manufactured from constituent materials conforming accordance with the requirements of BS EN 1015
to the following British/European Standard part 11.
specifications:
STRENGTH
Cementitious Materials BS EN 197-1, BS 7979

Fine aggregates BS EN 13139 BS EN 998-2 (iii) (ii) (i)

Mortar Class M4 M6 M12
Hydrated Lime BS EN 459-1
Compressive
Admixtures BS EN 934 Strength 4 6 12
N/mm2
Pigments BS EN 12878
Table 1 – BS EN 998-2 compressive strengths
made using prisms.

The information given in this technical data sheet is based on our current knowledge
For more details contact: and is intended to provide general notes on our products and their uses. Tarmac
03701 116 116 endeavour to ensure that the information given is accurate, but accept no liability for its
use or its suitability for particular application because of the product being used by the
mortar.internalsales@tarmacbp.co.uk third party without our supervision. Any existing intellectual property right must be
observed.

TARMAC.COM
FIRE PROTECTION allowing regular deliveries of up to 29 tonnes to
Tarmac Truspread Dry Silo Mortar contains less than ensure a continuous mortar supply.
1.0% organic material and is classified in accordance As an alternative to the silo, this can be supplied to
with BS EN 13501-1 as Class A1 without testing site in water resistant bulk bags.
(Commission Directive 96/603/EC).
TECHNICAL SUPPORT
DURABILITY Tarmac provides a comprehensive sales and
Tarmac Truspread Dry Silo Mortar is air entrained technical advisory service to specifiers and
which makes it less susceptible to freeze thaw attack. customers.
The admixture used to entrain air is chloride-free and
therefore not aggressive towards embedded metals. A quality system has been implemented throughout
the company since 1975 and quality procedures are
HEALTH & SAFETY in conformity with BS EN ISO 9001:2015. All Tarmac
factories hold third party certification from the British
There is a real danger of contact dermatitis or serious Standards Institution. Details of the certification
burns. To prevent skin coming into contact with wet status of individual factories may be obtained from
cement mixes such as fresh concrete, mortar or the technical helpdesk.
screed ensure that suitable protective clothing and
eye protection us worn. Where skin contact occurs PRICES AND CONDITIONS OF SALE
either directly or through saturated clothing wash Prices vary according to mix design, quantity and
immediately with soap and water. For eye contact, delivery location. For specific quotations contact your
immediately wash out eyes thoroughly with clean local Tarmac representative or call our National Sales
water. If swallowed wash out mouth and drink plenty Helpline on 03701 116 116.
of water. All quotations given, orders placed and materials
For further information please refer to Tarmac supplied are subject to the Conditions of Sale
Material Safety Data Sheet – Mortars, Screeds and available via download from the Tarmac website
Renders. www.tarmac.com or upon request from your nearest
Tarmac Regional Office.
APPLICATIONS
SUPPLY
USES Tarmac Truspread Dry Silo Mortars are available
Tarmac Truspread Dry Silo Mortar is suitable for all direct from mortar factories located strategically
types of construction, providing that the mortar type throughout mainland United Kingdom: contact your
and strength class chosen for a particular application nearest Tarmac Building Products Regional Office for
is suitable for its prescribed purpose. Advice on the further details
appropriate mortar for a given application is detailed
in all parts of Eurocode 6, BS EN 1996, UK National ORDERING
Annex to Eurocode 6, NA to BS EN 1996 and PD When ordering, please state mortar type and strength
6697. class, quantity, date and preferred time of delivery.
24 hours should normally be allowed for delivery.
ECONOMICS
Tarmac Truspread Dry Silo Mortars are sold by dry
weight. Yield - when mixed on site, 1 tonne of dry
silo mortar will produce approximately 0.70 cubic
metres of mortar.

One cubic metre of Tarmac Truspread Dry Silo

Mortar is sufficient to lay approximately 1700 bricks
(the actual number may however vary between 1300
and 2100 this depends upon the size of brick, depth
of frog, size of perforations, site practice and other
factors etc.) and approximately 1200 blocks of
nominal size 450 x 225 x 100mm.

DELIVERY
A silo on delivery holds approximately 14 tonnes of
dry material. Once sited, the silo can then be refilled
by tanker to hold up to 33 tonnes in total. It is good
practise to maintain the stock held within the silo

TARMAC.COM
 References
British Standards Institute
BS EN 197-1: Part 1: 2011 Cement Part 1: Composition, specifications and
conformity criteria for common cements

BS 7979: 2016 Specification for limestone fines for use with

Portland cement

BS EN 459: Part 1: 2015 Building lime. Definitions, specification and

conformity criteria

BS EN 12878: 2014 Pigments for the colouring of building materials

based on cement and/or lime specification and
methods of test

BS EN 13139: 2002 Aggregates for mortar

PD 6682 – 3: 2003 Aggregates – Part 3: Aggregates for mortar –

Guidance on the use of BS EN 13139

BS EN 13501 – 1: 2018 Fire classification of construction products and

building elements
Part 1: Classification using test data from fire
reaction tests

BS 4551: 2005 +A2: 2013 Mortar – Methods of test for mortar – Chemical
analysis and physical testing

BS EN 1996-1-1: 2005 +A1: 2012 Eurocode 6. Design of masonry structures.

General rules for reinforced and unreinforced
masonry structures

BS EN 1996-1-2: 2005 Eurocode 6. Design of masonry structures.

General rules. Structural fire design

BS EN 1996-2: 2006 Eurocode 6. Design of masonry structures.

Design considerations, selection of materials
and execution of masonry

BS EN 1996-3: 2006 Eurocode 6. Design of masonry structures.

Simplified calculation methods for unreinforced
masonry structures

NA to BS EN 1996-1-1: 2005 +A1: 2012 UK National Annex to Eurocode 6. Designs in

masonry structures. General rules for reinforced
and unreinforced masonry structures

NA to BS EN 1996-1-2: 2005 UK National Annex to Eurocode 6. Design of

masonry structures. General rules. Structural fire
design

NA to BS EN 1996-2: 2006 UK National Annex to Eurocode 6 Design of

masonry structures. Design considerations,
selection of materials and execution of masonry

TARMAC.COM
 NA to BS EN 1996-3: 2006 UK National Annex to Eurocode 6. Design of
masonry structures. Simplified calculation
methods for unreinforced masonry structures

PD 6697: 2010 Recommendations for the design of masonry

structures to BS EN 1996

PD 6678: 2005 Guide to the selection and specification of

masonry mortar

BS EN 1008: 2002 Mixing water for concrete – specification for

sampling, testing and assessing the suitability of
water, including water recovered from processes
in the concrete industry, as mixing water for
concrete

BS EN 934 Part 1: 2008 Admixtures for concrete, mortar and

grout
Part 2: 2009 +A1: 2012 Concrete admixtures –
definitions, requirements, conformity, marking
and labelling
Part 3: 2009 +A1: 2012 Admixtures for masonry
mortar – definitions, requirements, conformity,
marking and labelling

Building Research Establishment

Why do buildings crack?
Digest 361
Building mortar
Digest 362
Tarmac
Product Data Sheet No. 100/01 Tarmac Truspread Ready-to-Use mortar

Product Data Sheet No. 100/03 Hydrocure & Hydrocure+ Dry Silo Mortar

Site Guide No. 3 Ready-to-use mortars

Site Guide No. 6 Winter working recommendations for mortars

Site Guide No. 7 Summer working recommendation for mortars

Site Guide No. 9 Bulk Bags

Site Guide No. 10 Masonry cleaning

Tarmac Safety Data Sheet Mortars, Screeds and Renders

TARMAC.COM