OPERATION AND PARTS MANUAL

SERIES
MODEL MTX80
MODEL MTX90
TAMPING RAMMER
(ROBIN EH122D46530 GASOLINE ENGINE)

Revision #9 (1/14/11)

To find the latest revision of this

publication, visit our website at:
www.multiquip.com

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

 PROPOSITION 65 WARNING

PAGE 2 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 NOTES
NOTES

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 3

 TABLE OF CONTENTS
MTX80/MTX90 ROBIN EH122D46530
Tamping Rammer ENGINE
Proposition 65 Warning ........................................... 2 Crankcase Assembly ......................................... 40-41
Table Of Contents ................................................... 4 Cylinder Head Assembly .................................... 42-43
Parts Ordering Procedures ..................................... 5 Crankshaft, Piston Assembly ............................. 44-45
Safety Information ................................................ 6-9 Camshaft Assembly ........................................... 46-47
General Information .............................................. 10 Recoil Starter Assembly..................................... 48-49
Specifications ........................................................ 11 Carburetor Assembly (MTX80: S/N T-4419 and Below;
Components.......................................................... 12 MTX90: S/N T-1341 and Below) ......................... 50-51
Basic Engine ......................................................... 13 Carburetor Assembly (MTX80: S/N T-4420 and Above;
Operation ......................................................... 14-16 MTX90: S/N T-1342 and Above) ........................ 52-53
Maintenance ......................................................... 17 Air Cleaner Assembly......................................... 54-55
Troubleshooting ............................................... 18-19 Muffler Assembly ............................................... 56-57
Explanation Of Codes In Remarks Column .......... 20 Governor Assembly ........................................... 58-59
Suggested Spare Parts ......................................... 21 Flywheel Ignition Assembly ................................ 60-61
Name Plate and Decals ................................... 22-23 Labels and Accessories ..................................... 62-63
Crankcase and Engine Assembly .................... 24-27
Guide Cylinder and Spring Assembly .............. 28-29 Terms and Condition Of Sale — Parts .................... 64
Foot Assembly ................................................. 30-31
Tank and Handle Assembly ............................. 32-35
Combination Lever Assembly .......................... 36-37
Tools ................................................................. 38-39
NOTICE
Specification and part number are subject to
change without notice.

PAGE 4 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 PARTS ORDERING PROCEDURES
www.multiquip.com Ordering parts has never been easier!
Choose from three easy options: Effective:
January 1st, 2006
Best Deal! Order via Internet (Dealers Only): If you have an MQ Account, to obtain a Username
Order parts on-line using Multiquip’s SmartEquip website! and Password, E-mail us at: parts@multiquip.
■ View Parts Diagrams com.
■ Order Parts To obtain an MQ Account, contact your
■ Print Specification Information District Sales Manager for more information.

Goto www.multiquip.com and click on Use the internet and qualify for a 5% Discount
Order Parts to log in and save! on Standard orders for all orders which include
complete part numbers.*
Note: Discounts Are Subject To Change

Order via Fax (Dealers Only): Fax your order in and qualify for a 2% Discount
All customers are welcome to order parts via Fax. on Standard orders for all orders which include
Domestic (US) Customers dial: complete part numbers.*
1-800-6-PARTS-7 (800-672-7877) Note: Discounts Are Subject To Change

Order via Phone: Domestic (US) Dealers Call:

1-800-427-1244

Non-Dealer Customers:
Contact your local Multiquip Dealer for International Customers should contact
parts or call 800-427-1244 for help in their local Multiquip Representatives for
locating a dealer near you. Parts Ordering information.

When ordering parts, please supply:

❒ Dealer Account Number ❒ Specify Preferred Method of Shipment:
❒ Dealer Name and Address ✓ UPS/Fed Ex ✓ DHL
❒ Shipping Address (if different than billing address) ■ Priority One ✓ Truck
■ Ground
❒ Return Fax Number
■ Next Day
❒ Applicable Model Number ■ Second/Third Day
❒ Quantity, Part Number and Description of Each Part

NOTICE

All orders are treated as Standard Orders and will

ship the same day if received prior to 3PM PST.

WE ACCEPT ALL MAJOR CREDIT CARDS!

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 5

 SAFETY INFORMATION
Do not operate or service the equipment before reading Potential hazards associated with the operation of this
the entire manual. Safety precautions should be followed equipment will be referenced with hazard symbols which
at all times when operating this equipment. may appear throughout this manual in conjunction with
Failure to read and understand the safety safety messages.
messages and operating instructions could
result in injury to yourself and others.
SAFETY MESSAGES
The four safety messages shown below will inform you
about potential hazards that could injure you or others. The
safety messages specifically address the level of exposure
to the operator and are preceded by one of four words:
DANGER, WARNING, CAUTION or NOTICE.
SAFETY SYMBOLS
DANGER
Indicates a hazardous situation which, if not avoided,
WILL result in DEATH or SERIOUS INJURY.

WARNING
Indicates a hazardous situation which, if not avoided,
COULD result in DEATH or SERIOUS INJURY.

CAUTION
Indicates a hazardous situation which, if not avoided,
COULD result in MINOR or MODERATE INJURY.

NOTICE
Addresses practices not related to personal injury.

PAGE 6 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 SAFETY INFORMATION
GENERAL SAFETY „ ALWAYS know the location of the nearest phone or keep a
phone on the job site. Also, know the phone numbers of
CAUTION the nearest ambulance, doctor and fire department. This
„ NEVER operate this equipment without proper protective information will be invaluable in the case of an emergency.
clothing, shatterproof glasses, respiratory protection,
hearing protection, steel-toed boots and other protective
devices required by the job or city and state regulations.
RAMMER SAFETY
DANGER
„ NEVER operate this equipment when not „ NEVER operate the equipment in an explosive
feeling well due to fatigue, illness or when atmosphere or near combustible materials. An
under medication. explosion or fire could result causing severe
bodily harm or even death.
„ NEVER operate this equipment under the influence of
drugs or alcohol. WARNING
„ NEVER disconnect any emergency or safety devices.
These devices are intended for operator safety.
Disconnection of these devices can cause severe injury,
bodily harm or even death. Disconnection of any of these
„ ALWAYS check the equipment for loosened threads or devices will void all warranties.
bolts before starting.
„ DO NOT use this machine on ground that is harder than
„ DO NOT use the equipment for any purpose other than the machine can handle, or for driving pilings or tamping
its intended purposes or applications. rock beds. Furthermore, use of the machine on sloping
NOTICE ground, such as the side of an embankment, may make
the machine unstable and can cause an accident. It can
„ This equipment should only be operated by trained and also result in premature machine wear due to uneven
qualified personnel 18 years of age and older. loads on the machine.
„ Whenever necessary, replace nameplate, operation and Use the machine with confidence for tamping earth and
safety decals when they become difficult read. sand, soil, gravel, and asphalt. DO NOT use the machine
„ Manufacturer does not assume responsibility for any for other types of jobs.
accident due to equipment modifications. Unauthorized CAUTION
equipment modification will void all warranties.
„ NEVER lubricate components or attempt service on a
„ NEVER use accessories or attachments that are not running machine.
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result. NOTICE
„ ALWAYS know the location of the nearest „ ALWAYS keep the machine in proper running condition.
fire extinguisher. „ Fix damage to machine and replace any broken parts
„ ALWAYS know the location of the nearest immediately.
first aid kit. „ ALWAYS store equipment properly when it is not being
used. Equipment should be stored in a clean, dry location
out of the reach of children and unauthorized personnel.

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 7

 SAFETY INFORMATION
ENGINE SAFETY FUEL SAFETY
DANGER DANGER
„ The engine fuel exhaust gases contain poisonous carbon „ DO NOT add fuel to equipment if it is placed inside truck
monoxide. This gas is colorless and odorless, and can bed with plastic liner. Possibility exists of explosion or
cause death if inhaled. fire due to static electricity.
„ The engine of this equipment
requires an adequate free flow
of cooling air. NEVER operate
this equipment in any enclosed
or narrow area where free flow
of the air is restricted. If the air
flow is restricted it will cause
injury to people and property
and serious damage to the
equipment or engine.
WARNING
„ DO NOT place hands or fingers inside engine
compartment when engine is running.
„ NEVER operate the engine with heat shields or „ DO NOT start the engine near spilled fuel or combustible
guards removed. fluids. Fuel is extremely flammable and its vapors can
„ DO NOT remove the engine oil drain plug cause an explosion if ignited.
while the engine is hot. Hot oil will gush „ ALWAYS refuel in a well-ventilated area, away from
out of the oil tank and severely scald any sparks and open flames.
persons in the general area of the rammer.
„ ALWAYS use extreme caution when working with
CAUTION flammable liquids.
„ NEVER touch the hot exhaust manifold, „ DO NOT fill the fuel tank while the engine is running
muffler or cylinder. Allow these parts to cool or hot.
before servicing equipment.
„ DO NOT overfill tank, since spilled fuel could ignite if it
NOTICE comes into contact with hot engine parts or sparks from
„ NEVER run engine without an air filter or with a dirty air the ignition system.
filter. Severe engine damage may occur. Service air filter „ Store fuel in appropriate containers, in well-ventilated
frequently to prevent engine malfunction. areas and away from sparks and flames.
„ NEVER tamper with the factory settings „ NEVER use fuel as a cleaning agent.
of the engine or engine governor. Damage
to the engine or equipment can result „ DO NOT smoke around or near the
if operating in speed ranges above the equipment. Fire or explosion could result
maximum allowable. from fuel vapors or if fuel is spilled on a
hot engine.

PAGE 8 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 SAFETY INFORMATION
TRANSPORTING SAFETY
CAUTION
„ NEVER allow any person or animal to stand underneath
the equipment while lifting.
NOTICE
„ Before lifting, make sure that the equipment parts (hook
and vibration insulator) are not damaged and screws are
not loose or missing.
„ Always make sure crane or lifting device has been
properly secured to the lifting bail (hook) of the
equipment.
„ ALWAYS shutdown engine before transporting.
„ NEVER lift the equipment while the engine is running.
„ Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
„ Use adequate lifting cable (wire or rope) of sufficient
strength.
„ Use one point suspension hook and lift straight
upwards.
„ DO NOT lift machine to unnecessary heights.
„ ALWAYS tie down equipment during transport by
securing the equipment with rope.
„ Never allow any person or animal to stand underneath the
equipment while lifting.
ENVIRONMENTAL SAFETY
NOTICE
„ Dispose of hazardous waste properly.
Examples of potentially hazardous waste
are used motor oil, fuel and fuel filters.
„ DO NOT use food or plastic containers to dispose of
hazardous waste.
„ DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 9

 GENERAL INFORMATION
Definition of Tamping Rammer Handle Operation
The Mikasa MTX80/MTX90 tamping rammer is a powerful
compacting tool capable of applying a tremendous force in CAUTION
consecutive impacts to a soil surface. Its applications include
soil compacting for road, embankments and reservoirs as Before starting operation check the lifting
well as backfilling for gas pipelines, water pipelines and cable handle to:
installation work.
The impact force of the MTX80/MTX90 levels and uniformly
1. Make sure that there is no damage on the bolts.
compacts voids between soil particles to increase dry density.
2. Make sure that there is no crack or breakage on handle.
Circular motion is converted to create impact force. The
MTX80/MTX90 tamping rammer develops a powerful 3. Make sure that there is no fissure on the surface. If there
compacting force at the foot of the rammer. To maintain is any abnormality or damage, replace with new one.
optimum performance, proper operation and service are For operation:
essential.
This handle is to be used to lift up the shoe part of the machine
Construction of Tamping Rammer with the body laid down on the ground or truck bed.
The Mikasa MTX80/MTX90 is equipped with an air cooled, 1. Use proper lifting techniques to avoid back injury. This
four- cycle gasoline engine. Transmission of the power takes handle is for manual lifting only.
place by increasing the engine speed to engage the
2. Do not use this handle as a rammer lift point. Use the
centrifugal clutch.
lifting point on the top of the machine.
Rammer Gearbox and Spring Cylinder
3. Do not move the rammer with the lifting handle and the
The Mikasa MTX80/MTX90 uses an oil bath lubrication front rollers more than 16 feet (5 meters).
system. Always check the oil level through the oil level sight
glass at the rear of the tamper foot.
Controls
Before starting the MTX80/MTX90 Tamping Rammer identify
and understand the function of the controls.

PAGE 10 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 SPECIFICATIONS
Table 1. MTX80/MTX90 Rammer Specifications
Model MTX-80 MTX-90
Overall Height 39.37 in. (1000 mm) 39.37 in. (1000 mm)
Overall Width 14.37 in (365 mm) 14.37 in (365 mm)
Over Length 31.02 in (788 mm) 31.02 in (788 mm)
Shoe Size 13.4 x 11.2 in (340 x 285 mm) 13.4 x 11.2 in (340 x 285 mm)
Fuel Tank Capacity 3.2 qt. (3 liters) 3.2 qt. (3 liters)
Lubrication Oil Capacity 0.8 quart (0.75 liter) 0.8 quart (0.75 liter)
No. of Impacts Per Second 10.6 - 11.3 11.0 - 11.6
Impact Force 3,080 lb (13.7 kN) 3,530 lb (15.7 kN)
Impact Plate Stroke 2 - 3.15 in (50 - 80 mm) 2 - 3.15 in (50 - 80 mm)
Operating Weight 183 lbs. (83 kg) 196 lbs. (89 kg)
Speed Setting 3400-3600 rpm 3500-3700 rpm
Measured Sound Power Level 105 dB 105 dB
Guaranteed Sound Power
107 dB 107 dB
Level
Max. Sound Pressure Level 95 dB 97 dB

Table 2. Engine Specifications

Model Robin EH122D46530 Engine
Air-Cooled 4 Stroke, OHV,
Type
single cylinder gasoline engine
Piston Displacement 7.4 cu.in. (121 cc)
Max. Output 3.5 hp/3,600 rpm (2.6 KW)
Cooling System Air-Cooled
Engine Oil Capacity 0.42 qt. (0.4 liter)
Fu e l Unleaded gasoline
Lubricant for Engine Automobile Oil; Class SE or higher
Starting System Recoil Starter
Spark Plug Type NGK BR6ES

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 11

 COMPONENTS

3
2
4
10
1
5

6
11

7 12

8 13

Figure 1. MTX80/MTX90 Rammer

Figure 1 shows the location of the controls and components

for the MTX80/MTX90 Tamping Rammer. The functions of
each control is described below:
1. Combination (Throttle) Lever – Used to adjust engine 4. Hook – Used to lift rammer for transporting.
speed (rpm). Move lever forward (SLOW) to reduce 5. Air Cleaner Cover – Protects the air cleaner which
engine speed, move lever back toward operator (FAST) prevents dirt and other debris from entering the engine.
to increase speed. Always operate the rammer at full speed
6. Roller – Used for loading the rammer in back end of a
(rpm).
truck. Rammer is brought to tail gate roller side toward
2. Handle – To operate rammer, GRIP handle assembly the truck bed and driver lifts roller with handle at base and
firmly on both sides. rolls the unit into truck bed.
3. Fuel Tank Cap – Remove this cap to add unleaded 7. Bellows – Reservoir for oil bath.
gasoline to the fuel tank. Make sure cap is tightened 8. Foot – Laminated wood with tempered steel plate for
securely. DO NOT over fill. superior shock absorption.
WARNING 9. Fuel Tank – Holds the fuel for the unit (up to 3.2 quarts)
Add fuel to the tank only when the engine is 10. Muffler – reduces the noise of the engine when running.
stopped and has cooled down. In the event 11. Engine – this unit uses a Robin EH122D46530 gasoline
of a fuel spill, DO NOT attempt to start the engine.
engine until the fuel residue has been 12. Oil Gauge (Sight Glass) – Indicates the level of oil in the
completely wiped up and the area oil bath reservoir.
surrounding the engine is dry.
13. Drain Valve – Open this valve to remove oil from the
bellows.

PAGE 12 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 BASIC ENGINE

Figure 2. Engine Controls and Components

(Robin EH-12-2D)

The engine (Figure 2) must be checked for proper lubrication 4. Muffler – Used to reduce noise and emissions.
and filled with fuel prior to operation. Refer to the manufacturer's 5. Recoil Starter (pull rope) – Manual-starting method.
Engine manual for instructions & details of operation and Pull the starter grip until resistance is felt, then pull
servicing. briskly and smoothly.
1. Secondary Air Cleaner – Prevents dirt and other debris 6. Engine ON/OFF Switch – Controls the starting and
from entering the fuel system. Remove wing-nut on top stopping of the engine. Switch must be in the "ON"
of air filter cannister to gain access to filter element. position when starting the engine.
2. Choke Lever – Used when starting the engine. Normally
used in cold weather conditions. In cold weather turn
the choke lever to the fully closed position, in warm WARNING
weather set choke lever half way or completely open. Engine components can generate extreme
3. Spark Plug – Provides spark to the ignition system. heat.To prevent burns, DO NOT touch these
Set spark plug gap to 0.024 - 0.028 inch (0.6 - 0.7 mm). areas while the engine is running or
Clean spark plug once a week. immediately after operating. NEVER operate
the engine with the muffler removed.
NOTICE
Operating the engine without an air filter, with a damaged air
filter, or a filter in need of replacement will allow dirt to enter
the engine, causing rapid engine wear.

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 13

 OPERATION
This section is intended to assist the operator with the initial Engine
start-up of the MTX80/MTX90 Tamping Rammer. It extremely 1. Fill the fuel tank (Figure 4) with unleaded gasoline. At the
important that this section be read carefully before attempting same time, check the engine oil and make it a habit to
to operate the rammer. replenish it often (Figure 5).
DO NOT use your rammer until this section is thoroughly
understood.

CAUTION FUEL
TANK
Failure to understand the operation of the MTX80/MTX90
Tamping Rammer could result in severe damage to the
unit or personal injury.

Rammer Crankcase and Spring Cylinder Oil Bath

This unit uses an oil bath lubrication system. Perform the following:
1. Check the oil level through the oil level sight glass (Figure 3) Figure 4. Fuel Tank
at the rear of the tamper foot.
OIL LEVEL
DIPSTICK
OIL FILL PLUG
SIGHT GLASS
OIL DRAIN PLUG

Figure 5. Engine Oil Dipstick

2. Check the engine oil level and if the engine oil level is low,
it should be refilled. Low levels of oil may result in engine
Figure 3. Foot Housing Sight Glass seizure. Use the proper motor oil as suggested in the Table
3 below.
2. If oil is not visible, add 10W-30 SE, SF or higher grade motor
oil into the oil fill plug opening (Figure 3). The bath contains
approximately 1.7 pints (800 cc.) Table 3 Motor Oil Grade
Grade of motor oil
Season or Temperature
NOTICE (higher than MS class)

The oil level should be kept at the half way point of the sight Spring, Summer or Autumn
SAE 30
glass. +120° F to +15° F
Winter
SAE 30
+40° F to +15° F

Below +15° F SAE 10W-30

PAGE 14 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 OPERATION
Inspection
NOTICE
1 . Check all nuts, bolts fasteners for tightness. Retighten as
necessary. DO NOT press the primer pump bulb more than four
(4) times, as this will cause fuel to flood the carburetor.
2. Clean any dirt from the recoil starter and foot pedestal. Wipe
the entire unit clean before operating.
3. Replace any missing or damaged Safety Operation decals. 3. Place the choke lever to the closed position (Figure 7).When
4. Adjust height of handle. Adjust handle by loosening nuts and the weather is cold, close the choke all the way.When it is hot,
moving handle to suit operation. Retighten nuts. or if the engine is hot, open the choke a little or leave it fully
Initial Start-up open.
When starting the MTX80/MTX90 Tamping Rammer perform
the following:
1. Slide the throttle lever from the stop to the idle position ( ) CHOKE LEVER
(Figure 6).This opens the fuel cock and the engine electrical (CLOSED POSITION)
circuit is turned on automatically.

Figure 7. Choke Lever

THROTTLE LEVER
(IDLE POSITION) 4. Grip the starter rope handle (Figure 8) and pull it until you
feel a slight resistance.Then pull sharply and quickly. Return
the handle to the starter case before releasing.

Figure 6-A. Throttle Lever (Idle {Position)

2. Units with Carburetor Primer System: Push the STARTER

primer pump bulb four (4) times to deliver fuel to the ROPE
carburetor (Figure 5-B).

Figure 8. Recoil Starter

5. If engine fails to start, move the choke lever to the half open
position to avoid flooding.
6. Repeat steps 1 thru 5.
7. If the engine does not start after repeated attempts,
check the spark plug for excess fuel. Clean and replace
the spark plug as needed.

Figure 6-B. Primer Pump

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 15

 OPERATION
Operation Stopping The Engine
1. To start the rammer tamping action, move the throttle lever Normal Shutdown
(Figure 9) quickly from IDLE to the START ( ) position. 1. Move throttle lever quickly from the START to IDLE position
DO NOT move the throttle lever slowly as this may cause (Figure 10) and run the engine for three minutes at low speed.
damage to the clutch or spring. After the engine cools, move the throttle lever to the STOP
position (Figure 11). The engine will stop and the fuel cock
is automatically closed.

THROTTLE LEVER THROTTLE LEVER

(START POSITION) (STOP POSITION)

Figure 9. Throttle Lever (Start Position)

Figure 11. Throttle Lever (Stop Position)
CAUTION
2. If the engine does not stop due to a problem with the switch
Make sure that the throttle lever is moved to the FULL START or the like, move the machine to a safe location and hold the
position. Operating the rammer at less than full speeds can throttle lever in the stop position. Let the machine run on idle
result in damage to the clutch springs or foot. and the machine will stop after a few minutes.

2. The MTX80/MTX90 tamping rammer is designed to run at

3,600/3700 rpm. At optimum rpm the foot hits at the rate
between 590 ~ 695 impacts per minute. Increasing throttle
speed past factory set rpm does not increase impacts and
may damage unit. The MTX80/MTX90 is designed to ad-
vance while tamping. For faster advance, pull back slightly
on the handle so that rear of foot contacts soil first.
3. To stop the tamping action, move throttle lever quickly from
START to IDLE position (Figure 10).

THROTTLE LEVER
(IDLE POSITION)

Figure 10. Throttle Lever (Idle Position)

PAGE 16 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 MAINTENANCE
Maintenance EVERY 200 HOURS
Perform the scheduled maintenance procedures as indicated: ■ Remove the oil drain plug on foot housing (Figure 14) and
drain the oil. Refill with approximately 1.7 pt. (800 cc.) of
DAILY
10W-30 SE, SF or higher grade motor oil. Oil should be
■ Thoroughly remove dirt and oil from the engine and control midway in sight glass. Break in oil should be changed after
area. first 50 hours.
■ Clean or replace the air cleaner elements as necessary.
Check and retighten all fasteners as necessary. OIL FILL PLUG
■ Check the spring box and bellows for oil leaks. Repair or SIGHT GLASS
replace as needed.
OIL DRAIN PLUG
EVERY 50 HOURS
■ Remove the fuel filter cap and clean the inside of the fuel
tank (Figure 12).

Figure 14. Oil Drain Plug

EVERY 2YEARS
■ Replace the fuel line every 250 hours or every 2 years even
if there is no visible damage.
Long Term Storage
FUEL FILTER
■ Slide the throttle lever to the STOP position.
■ Drain any fuel including in the fuel hose.
■ Replace lubrication oil and apply grease to lubrication
Figure 12. Fuel Filter
points.
■ Remove and clean the spark plug, then adjust the spark gap ■ Cover the air intake on the air cleaner and the exhaust outlet
to 0.024~0.028 inch (0.6~0.7 mm). on the muffler.
EVERY 80 to 100 HOURS ■ Store unit indoors covered with plastic sheet in moisture
■ Remove the air cleaner cover. Loosen and remove the 2 free and dust free location out of direct sunlight.
screws that hold the cover to the air cleaner assembly. If the
primary element (Figure 13) is dirty, wash it with gasoline or
kerosene. Then dip it in engine oil (SAE10W-30) and wring
the element so that 25 to 30 cc of engine oil remains on the
element.

PRIMARY
ELEMENT
Figure 13. Air Cleaner Primary Element

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 17

 TROUBLESHOOTING

TABLE 4. ENGINE TROUBLESHOOTING

SYMPTOM POSSIBLE PROBLEM SOLUTION

Difficult to start

Ignition plug being bridge? Check ignition system.

Carbon deposit at ignition? Clean or replace ignition.

Fuel is available but spark plug
will not ignite. (Power available
at high tension cable). Short circuit due to defective Replace insulators.
insulators?

Improper spark gap? Set spark plug gap to the correct gap.

Fuel is available but spark plug Short circuit at stop switch? Check stop switch circuit. Replace stop switch if defective.
will not ignite. (Power NOT
available at high tension cable). Ignition coil defective? Replace ignition coil.

Muffler clogged with carbon Clean or replace muffler.

deposits?
Fuel is available and spark plug Fuel in use inadequate (water, Flush fuel sytem and replace with fresh fuel.
ignites (compression normal). dust)?

Air Cleaner clogged? Clean or replace air cleaner.

Defective cylinder head gasket? Tighten cylinder head bolts or replace head gasket.
Fuel is available and spark plug Cylinder worn? Replace cylinder.
ignites (compressionlow).
Spark plug loose? Tighen spark plug.

Low compression. Incorrect valve adjustment? Check and adjust valves.

Operation not satisfactory

Air cleaner clogged? Clean or replace air cleaner.

Not enough power available
(compression normal, no miss- Air in fuel line? Bleed (remove air) from fuel line.
firing).
Carbon deposits in cylinder? Clean or replace cylinder

Ignition coil defective? Flush fuel sytem and replace with fresh fuel.
Not enough power available
(compression normal, miss- Ignition plug often shorts? Replace ignition wires, clean ignition.
firing).
Fuel in use inadequate (water, Flush fuel sytem and replace with fresh fuel.
dust)?

Excessive carbon depostion in Clean or replace crankcase.

combustion chamber?

Engine overheats. Exhaust or muffler clogged with Clean or replace muffler.

carbon.

Spark plug heat value incorrect? Replace spark plug with correct type spark plug.

Engine high speed incorrect. Incorrect engine RPM? Check and adjust engine RPM to 3400-3600 RPM.

PAGE 18 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 TROUBLESHOOTING

ENGINE
TABLE 4. ENGINE TROUBLESHOOTING (continued)

SYMPTOM POSSIBLE PROBLEM SOLUTION

Operation not satisfactory

Governor adjustment improper? Adjust governor to correct lever.

Governor spring defective? Clean or replace ignition.

Rotational speed fluctuates.
Fuel flow erratic? Check fuel line.

Air taken in through suction Check suction line.

line?

Dust in rotating par t? Clean recoil star ter assembly.

Recoil star ter not working
properly.
Spring spring failure? Replace sprial spring.

TABLE 5. RAMMER TROUBLESHOOTING

SYMPTOM POSSIBLE PROBLEM SOLUTION

Operating speed of throttle lever Set throttle lever to correct position.

is incorrectly set?

Oil in excess? Drain excess oil. Bring to correct level.

Engine runs but rammer jumps Clutch slips? Replace or adjust clutch.
erratically or not at all..
Spring Failure? Replace sprial spring.

Speed of engine improper? Adjust engine speed to correct operating RPM setting.

Soil over-compacted? Shut-down machine and test soil.

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 19

 EXPLANATION OF CODES IN REMARKS COLUMN
The following section explains the different symbols and QTY. Column
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there Numbers Used — Item quantity can be indicated by a
are any questions. number, a blank entry, or A/R.

NOTICE A/R (As Required) is generally used for hoses or other

parts that are sold in bulk and cut to length.
The contents and part numbers listed in the parts
section are subject to change without notice. Multiquip A blank entry generally indicates that the item is not sold
does not guarantee the availability of the parts listed. separately. Other entries will be clarified in the “Remarks”
Column.
SAMPLE PARTS LIST REMARKS Column
NO. PART NO. PART NAME QTY. REMARKS
Some of the most common notes found in the “Remarks”
1 12345 BOLT......................1 .....INCLUDES ITEMS W/%
2% WASHER, 1/4 IN............NOT SOLD SEPARATELY Column are listed below. Other additional notes needed
2% 12347 WASHER, 3/8 IN....1 .....MQ-45T ONLY to describe the item can also be shown.
3 12348 HOSE ..................A/R ...MAKE LOCALLY
4 12349 BEARING ..............1 .....S/N 2345B AND ABOVE Assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
NO. Column purchased.
Unique Symbols — All items with same unique Indicated by:
symbol “INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the Serial Number Break — Used to list an effective serial
same assembly or kit, which is indicated by a note in the number range where a particular part is used.
“Remarks” column.
Indicated by:
Duplicate Item Numbers — Duplicate numbers indicate “S/N XXXXX AND BELOW”
multiple part numbers, which are in effect for the same “S/N XXXX AND ABOVE”
general item, such as different size saw blade guards in “S/N XXXX TO S/N XXX”
use or a part that has been updated on newer versions
of the same machine. Specific Model Number Use — Indicates that the part
is used only with the specific model number or model
NOTICE number variant listed. It can also be used to show a
When ordering a part that has more than one item part is NOT used on a specific model or model number
number listed, check the remarks column for help in variant.
determining the proper part to order. Indicated by:
“XXXXX ONLY”
PART NO. Column
“NOT USED ON XXXX”
Numbers Used — Part numbers can be indicated by a “Make/Obtain Locally” — Indicates that the part can
number, a blank entry, or TBD. be purchased at any hardware shop or made out of
TBD (To Be Determined) is generally used to show a available items. Examples include battery cables, shims,
part that has not been assigned a formal part number and certain washers and nuts.
at the time of publication. “Not Sold Separately” — Indicates that an item cannot
A blank entry generally indicates that the item is not sold be purchased as a separate item and is either part of an
separately or is not sold by Multiquip. Other entries will assembly/kit that can be purchased, or is not available
be clarified in the “Remarks” Column. for sale through Multiquip.

PAGE 20 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 SUGGESTED SPARE PARTS
MTX80/MTX90 RAMMER 1 TO 3 UNITS
WITH ROBIN EH122D46530 ENGINE
Qty. P/N Description
1 ......... 956100063 ....... THROTTLE WIRE
3 ......... 366010070 ....... PRIMARY ELEMENT, AIR CLEANER
3 ......... 366010080 ....... SECONDARY ELEMENT, AIR CLEANER
1 ......... 366900020 ....... CAP, FUEL TANK W/ STRAP
2 ......... 26365012A3 .... FILTER, IN-LINE FUEL
3 ......... 0650140580 ..... SPARK PLUG
1 ......... 959300770 ....... STRAINER, FUEL TANK
1 ......... 2825011118 ..... ROPE, RECOIL STARTER

NOTICE
Part numbers on this Suggested Spare Parts List may
supersede/replace the P/N shown in the text pages of
this book.

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 21

 NAMEPLATE AND DECALS

1
4

7
NPA-0000

? ? ? ? ?

? ? NPA-1245

5
STOP

NPA-0000

NPA-0000

11

MODEL
SERIAL NO.

A (DECAL SET)
8

MTX series

RAMMER

quick manual

Engine Oil
Use SAE 10W/30,SE or higher grade motor oil

RAMMING CYLINDER OIL

Use SAE 10W/30,SF or higher grade moter oil

Fuel
Use normal quality gasoline

PAGE 22 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 NAMEPLATE AND DECALS
NO PART NO PART NAME QTY. REMARKS
A 920900040 DECAL SET ..................................... 1 .......... INCLUDES ITEMS W/ #
1# DECAL: OPERATION 1
2# DECAL: AIR CLEANER 1
3# DECAL: LEVER OPERATION 1
4# DECAL: MAX SPEED 1
5# DECAL: MACHINE STOP 1
6# DECAL: EC NOISE REQ 1
7# DECAL: ANTI-VIB HANDLE 1
8 920212540 QUICK MANUAL 1
11 DECAL: NAMEPLATE ...................... 1 .......... CONTACT MQ PARTS DEPT W/ SERIAL NO.

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 23

 CRANKCASE AND ENGINE ASSY.

46

43
44 47 47
44
35-4 75-1
35-3 75-2
35-2 75-3
35-1

35 35-7 70 74 73
35-9

35-8
39
40-1 111
78 80
35-5 40-2 82
40-3
79
37 36 37
55-1 59 OLD
55-2 STYLE
31-1 38 CLUTCH
52
31-2 22
41-2 NEW
48 41-1 STYLE 22
53 CLUTCH
49
54 65
34 63
49 33 65 64
55-2 77 63
32 23 64
55-1 30 24-2
48 27 24-1 68
67 61
58
45
26 57
25
4
51
56 60
A
1 59 56
28-2
28-1 53
54 62 66
16
815
13 55-2
A
101 55-1
10
9
11
5
3
7
6
18
106 14
12
19
81
20

PAGE 24 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 CRANKCASE AND ENGINE ASSY.
NO. PART NO. PART NAME QTY. REMARKS
1 366118940 CRANK CASE 1
3 041006007 BEARING 6007Z 1
4 367345180 PINION, DRUM 1
5 060404010 OIL SEAL TC-40528 1
6 080200350 STOP RING S-35 1
7 080100620 STOP RING R-62 1
8 040006207 BEARING 6207 1
9 040006305 BEARING 6305 1
10 080100720 STOP RING R-72 1
11 080200350 STOP RING S-35 1
12 080200250 STOP RING S-25 1
13 366345230 CONNECTING ROD 1
14 040006304 BEARING 6304 1
15 080100520 STOP RING R-52 1
16 080200200 STOP RING S-20 1
18 047940060 NEEDLE BEARING FJ-1816 1
19 050710080 O-RING AS568-267 1
20 001520825 SOCKET HEAD BOLT 8X25 T 8
22 366346210 CLUTCH ASSY ....................................... 1 ......... MTX80: S/N S-3939 AND BELOW
............................................................................. MTX90: S/N S-1298 AND BELOW
22 366348550 CLUTCH ASSY ....................................... 1 ......... MTX80: S/N S-3940 AND ABOVE
............................................................................. MTX90: S/N S-1299 AND ABOVE
23 952401450 WASHER 8.5X22X3 1
24-1 001220825 BOLT 8X25 T 1
24-2 030208200 WASHER, LOCK M8 1
25 367217260 FLANGE, ENGINE 1
26 001710830 FLANGE BOLT 8X30 4
27 022611010 FLANGE NUT M10 H 2
28-1 001221054 BOLT 10X70 T 2
28-2 030210250 WASHER, LOCK M10 2
30 366346280 BRACKET, SHOCK ABSORBER 1
31-1 001211030 BOLT 10X30 H 4
31-2 030210250 WASHER, LOCK M10 4
32 939010270 STOPPER RUBBER ( 70 ) 1
33 030208200 WASHER, LOCK M8 1
34 020308060 NUT M8 1
35 366900010 AIR CLEANER ASSY ............................... 1 ......... INCLUDES ITEMS W/ #
35-1# 366010010 AIR CLEANER COVER 1
35-2# 366010020 WASHER, FLAT M6 2
35-3# 366010030 WASHER, LOCK M6 2
35-4# 366010040 COIN BOLT M6 2
35-5# 366010050 BASE CP, AIR CLEANER 1
35-7# 366010070 PRIMARY ELEMENT CP 1
35-8# 366010080 SECONDARY ELEMENT 1
35-9# 362030040 GRIP BOLT CP, AIR CLEANER 1
36 367217460 PIPE, INTAKE 1
37 954407682 CYCLONE CLAMP (CY-1) 38 2
38 366460160 SEALING FORM, UNDER 1
39 366460150 SEALING FORM, SIDE 1

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 25

 CRANKCASE AND ENGINE ASSY.

46

43
44 47 47
44
35-4 75-1
35-3 75-2
35-2 75-3
35-1

35 35-7 70 74 73
35-9

35-8
39
40-1 111
78 80
35-5 40-2 82
40-3
79
37 36 37
55-1 59 OLD
55-2 STYLE
31-1 38 CLUTCH
52
31-2 22
41-2 NEW
48 41-1 STYLE 22
53 CLUTCH
49
54 65
34 63
49 33 65 64
55-2 77 63
32 23 64
55-1 30 24-2
48 27 24-1 68
67 61
58
45
26 57
25
4
51
56 60
A
1 59 56
28-2
28-1 53
54 62 66
16
815
13 55-2
A
101 55-1
10
9
11
5
3
7
6
18
106 14
12
19
81
20

PAGE 26 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 CRANKCASE AND ENGINE ASSY.
CONTINUED
NO. PART NO. PART NAME QTY. REMARKS
40-1 001220851 BOLT 8X55 T 2
40-2 030208200 WASHER, LOCK M8 2
40-3 031108160 WASHER, FLAT M8 2
41-1 001210815 BOLT 8X15 H 2
41-2 030208200 WASHER, LOCK M8 2
43 366217340 COVER, CLEANER ASSY (UPPER) 1
44 366460140 RUBBER BUSH (10X16X17) 2
45 366217350 COVER, CLEANER ASSY (UNDER) 1
46 366345980 KNOB, CLEANER COVER 2
47 050200060 O-RING P6 2
48 009110040 FLANGE BOLT 8X20 4
49 959407670 SQUARE NUT M8 4
51 367118990 GUARD, LINK 1
52 367119000 GUARD, MUFFLER 1
53 022910260 WELL NUT M8 2
54 366460170 FLANGE COLLAR 8 2
55-1 001520820 SOCKET HEAD BOLT 8X20 T 4
55-2 031108160 WASHER, FLAT M8 4
56 009110038 SOCKET HEAD BOLT 8X30 ZN 2
57 367217490 EX BAR 1
58 009110039 SOCKET HEAD BOLT 6X25 ZN 4
59 022910250 WELL NUT M6 4
60 367119010 GUARD, ENGINE 1
61 367346290 SUPPORT, ENGINE 1
62 009110042 S.H.BOLT8X45 WHOLE THREAD 2
63 030208200 WASHER, LOCK M8 4
64 031108160 WASHER, FLAT M8 4
65 020308060 NUT M8 4
66 009110043 SOCKET HEAD BOLT 8X40 ZN 2
67 001520820 SOCKET HEAD BOLT 8X20 T 2
68 030208200 WASHER, LOCK M8 2
70 366900042 COMBINATION LEVER ASSY W/ WIRE ........ 1 ......... INCLUDES ITEMS W/@
74@ 956100063 THROTTLE WIRE 1
75-1 001220620 BOLT 6X20 T 2
75-2 030206150 WASHER, LOCK M6 2
75-3 031106100 WASHER, FLAT M6 2
76 020306050 NUT M6 2
77 959006120 CLIP (TCP2-10509B) 1
78 367460120 WIRE HARNESS 1
79 2067550101 CLAMP COMPL 1
80 959021810 SPIRAL TUBE KEP6/L=500 1
81 454010020 CLAMP TC-100 5
82 954010280 CLIP AB-4N 1
101 367345200 CRANK GEAR 1
106 366010120 FRONT COVER ............................................. 1 ......... FOR MTX80, S/N S-3939 AND BELOW
106 366010121 FRONT COVER ............................................. 1 ......... FOR MTX80, S/N S-3940 AND ABOVE
106 366010130 FRONT COVER ............................................. 1 ......... FOR MTX90, S/N S-1298 AND BELOW
106 366010131 FRONT COVER ............................................. 1 ......... FOR MTX90, S/N S-1299 AND ABOVE
111 911211217 ENGINE ASSY, EH122D46530 1

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 27

 GUIDE CYLINDER AND SPRING ASSY.

32
1
2

3 20

9
22

21

24

8 12
27
14 18 17 26 28
25
29
13

15 16 23
29
9

27

26 28
25
7
24
31
4 30
6 51 52
5-2
5-1 53

PAGE 28 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 GUIDE CYLINDER AND SPRING ASSY.
NO. PART NO. PART NAME QTY. REMARKS
1 366460100 PISTON PIN 1
2 366459910 PLUG, PISTON PIN 2
3 366346000 PISTON ROD 1
4 371459690 PISTON END 1
5-1 001221230 BOLT 12X30 T 1
5-2 030212300 WASHER, LOCK M12 1
6 952404790 WASHER 13306 1
7 355447260 STOPPER, LOWER 1
8 366459900 STOPPER, BOTTOM 1
9 366459730 MAIN SPRING 2
12 366345990 SPRING CYLINDER 1
13 366217210 FOOT PLATE 12 1
14 050100900 O-RING G-90 1
15 001521020 SOCKET HEAD BOLT 10X20 T 4
16 001521040 SOCKET HEAD BOLT 10X40 T 4
17 953405270 PLUG 1/4X14 13L 1
18 953405260 PACKING 1/4 (CU) 1
20 366217440 GUIDE CYLINDER ...................................... 1 .......... FOR MTX80
20 367217450 GUIDE CYLINDER ...................................... 1 .......... FOR MTX90
21 050710070 O-RING AS568-344 1
22 002211035 BOLT 10X35 H, SW .................................... 4 .......... FOR MTX80
22 002211045 BOLT 10X45 H, SW .................................... 4 .......... FOR MTX90
23 354010010 BELLOWS, ORANGE 1
24 050931500 O-RING JASO3150 2
25 354336352 BELLOWS CLAMP( 1.6T)171D 2
26 354442340 BAND GUIDE, BELLOWS 2
27 001220840 BOLT 8X40 T 2
28 020308060 NUT M8 2
29 354446170 PIN 6D-8.5L 2
30 953405270 PLUG 1/4X14 13L 1
31 953405260 PACKING 1/4 (CU) 1
32 050200950 O-RING P-95 1
51 366118590 PROTECTION SLEEVE 1
52 366460300 OIL GAUGE ASSY 1
53 953404670 COPPER PACKING 17X25.5X1 1

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 29

 FOOT ASSY.

2
3

6
2
3

7
8

1
9

4 5

PAGE 30 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 FOOT ASSY.
NO. PART NO. PART NAME QTY. REMARKS
1 366910020 FOOT ASSY 285 1
2 022711214 NYLON NUT M12 4
3 030212300 WASHER, LOCK M12 4
4 009110034 BOLT, SQUARE NECK 12X65 2
5 009110035 BOLT, SQUARE NECK 12X95 2
6 363343390 GRIP HANDLEBAR 1
7 015110055 SUNK HEAD BOLT 10X55 H 7
8 030210250 WASHER SW M10 7
9 021110120 NYLON NUT M10 7

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 31

 TANK AND HANDLE ASSY.

10
54
51
53

56

22
14
15
110 16 B
A
3 18
17

55

12
11-2
11-1
12
11-2
11-1
4-1
4-2
7 13
6 112
B
43 11-2 111
5 11-1 102
41 20 19 101
43 A
4-2 102
4-1
42 103
41 20
113 102
42 104
112

106

1
2-2
2-1

102 105

PAGE 32 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 TANK AND HANDLE ASSY.
NO. PART NO. PART NAME QTY. REMARKS
1 366346270 SHOCK ABSORBER W/PIN 2
2-1 001521020 SOCKET HEAD BOLT 10X20 T 4
2-2 033121009 TOOTHED LOCK WASHER B M10 4
3 367119050 HANDLE 1
4-1 001211020 BOLT 10X20 H 4
4-2 030210250 WASHER, LOCK M10 4
5 939010270 STOPPER RUBBER (70) 1
6 030208200 WASHER, LOCK M8 1
7 020308060 NUT M8 1
9 366900020 CAP ASSY, FUEL TANK 1
10 366118700 FUEL TANK 1
11-1 001210815 BOLT 8X15 H 3
11-2 030208200 WASHER, LOCK M8 3
12 952401450 WASHER 8.5X22X3 2
13 031108160 WASHER, FLAT M8 1
14 959300770 STRAINER #508 1
15 366459790 PACKING, FUEL TANK 1
16 366345280 HOLDER, FILTER ................................... 1 ......... MTX80 S/N T-4419 AND BELOW
............................................................................. MTX90 S/N T-1341 AND BELOW
16% 366345280 HOLDER, FILTER ................................... 1 ......... MTX80 S/N T-4420 AND ABOVE
............................................................................. MTX90 S/N T-1342 AND ABOVE
17 020305040 NUT M5 3
18 030205130 WASHER, LOCK M5 3
19 959026122 FUEL HOSE L=70 ................................... 1 ......... MTX80 S/N T-4164 AND BELOW
............................................................................. MTX90 S/N T-1331 AND BELOW
19 0851041780 FUEL HOSE FOR EVP L=70 .................. 1 ......... MTX80 S/N T-4165 AND ABOVE
............................................................................. MTX90 S/N T-1332 AND ABOVE
20 954406420 HOSE BAND 10.5 ................................... 2 ......... MTX80 S/N T-4164 AND BELOW
............................................................................. MTX90 S/N T-1331 AND BELOW
20 0561080020 HOSE CLAMP ........................................ 2 ......... MTX80 S/N T-4165 AND ABOVE
............................................................................. MTX90 S/N T-1332 AND ABOVE
22 009110037 TAPPING SCREW 5X20 2
41 366217170 ROLLER 2
42 091005020 SCREW 5X20 4
43 022610505 FLANGE NUT M5 H 4

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 33

 TANK AND HANDLE ASSY.

10
54
51
53

56

22
14
15
110 16 B
A
3 18
17

55

12
11-2
11-1
12
11-2
11-1
4-1
4-2
7 13
6 112
B
43 11-2 111
5 11-1 102
41 20 19 101
43 A
4-2 102
4-1
42 103
41 20
113 102
42 104
112

106

1
2-2
2-1

102 105

PAGE 34 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 TANK AND HANDLE ASSY.
CONTINUED
NO. PART NO. PART NAME QTY. REMARKS
51 955010311 TP22 TACHO/HOUR METER 1
53 955010305 CURL CORD TP22 1
54 366345620 FINISHER, METER 1
55 454010020 CLAMP, TC100 5
56 954010270 CLIP AB-3N 1
101 959026121 FUEL HOSE L=170 ................................. 1 ......... MTX80 S/N T-4164 AND BELOW
............................................................................. MTX90 S/N T-1331 AND BELOW
101 0851041800 FUEL HOSE FOR EVP L=170 ................ 1 ......... MTX80 S/N T-4165 AND ABOVE
............................................................................. MTX90 S/N T-1332 AND ABOVE
102 954406420 HOSE BAND 10.5 ................................... 4 ......... MTX80 S/N T-4164 AND BELOW
............................................................................. MTX90 S/N T-1331 AND BELOW
102 0561080020 HOSE CLAMP ........................................ 4 ......... MTX80 S/N T-4165 AND ABOVE
............................................................................. MTX90 S/N T-1332 AND ABOVE
103 26365012A3 FILTER, FUEL CP 1
104 959021722 FUEL HOSE L=250 1 MTX80 S/N T-4164 AND BELOW
............................................................................. MTX90 S/N T-1331 AND BELOW
104 0851041760 FUEL HOSE FOR EVP L=260 ................ 1 ......... MTX80 S/N T-4165 AND ABOVE
............................................................................. MTX90 S/N T-1332 AND ABOVE
105 959021824 SPIRAL TUBE D=6, L=110 ..................... 1 ......... MTX80 S/N T-4165 AND ABOVE
............................................................................. MTX90 S/N T-1332 AND ABOVE
106 959407720 TUBE, V 11X13X180 1
110 366900060 PRIMER PUMP KIT/NO CARB .............. 1 ......... INCLUDES ITEMS W/ %
............................................................................. MTX80 S/N T-4420 AND ABOVE
............................................................................. MTX90 S/N T-1342 AND ABOVE
111% 959028301 RETURN HOSE 3X6X600....................... 1 ......... MTX80 S/N T-4420 AND ABOVE
............................................................................. MTX90 S/N T-1342 AND ABOVE
112% 954408170 HOSE CLIP 5 .......................................... 2 ......... MTX80 S/N T-4420 AND ABOVE
............................................................................. MTX90 S/N T-1342 AND ABOVE
113% 959021814 SPIRAL TUBE 6D-200L .......................... 1 ......... MTX80 S/N T-4420 AND ABOVE
............................................................................. MTX90 S/N T-1342 AND ABOVE

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 35

 COMBINATION LEVER ASSY.

A 4
7
8

7 3

11
1

13

10

BODY

5
14
11
6
12
9

NOTES
OLD STYLE LEVER BODY NO LONGER
AVAILABLE. NEW STYLE ITEMS 1, 2, AND 9
OLD NEW ARE NOT COMPATIBLE WITH OLD STYLE
STYLE STYLE BODY. IF REPLACEMENT OF ITEMS 1, 2
LEVER LEVER OR 9 IS REQUIRED, ORDER KIT “A”.

TO DETERMINE IF COMBINATION LEVER

ASSY IS OLD STYLE OR NEW STYLE, SEE
ITEM 2, LEVER. NEW STYLE LEVER HAS
MOLDED TAB AT BOTTOM.

MOLDED
TAB

PAGE 36 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 COMBINATION LEVER ASSY.
NO. PART NO. PART NAME QTY. REMARKS
A 366900042 COMB. LEVER ASSY W/ THROTTLE WIRE ..... 1 ......... INCLUDES ITEMS W/ #
....................................................................................... REPLACES 366900041
A 956200110 COMB. LEVER ASSY ....................................... 1 ......... INCLUDES ITEMS W/@
1 366346260 FUEL COCK ...................................................... 1 ......... SEE NOTE ON DRAWING
1#@ 366349430 FUEL COCK ...................................................... 1 ......... NEW STYLE, SEE NOTE ON DRAWING
2 366010180 LEVER ............................................................... 1 ......... SEE NOTE ON DRAWING
2#@ 366010310 LEVER ............................................................... 1 ......... NEW STYLE, SEE NOTE ON DRAWING
3#@ 366010190 SLIDER 1
4#@ 366010200 END CAP 1
5#@ 366010210 WIRE CAP 1
6#@ 366010220 BOLT AND WASHER SET 1
7#@ 020408050 NUT M8, H=5 2
8#@ 959407650 SOCKET HEAD SCREW/TH.WIRE 1
9 366010260 STOP SWITCH .................................................. 1 ......... SEE NOTE ON DRAWING
9#@ 366010320 STOP SWITCH .................................................. 1 ......... NEW STYLE, SEE NOTE ON DRAWING
10# 956100063 THROTTLE WIRE 1
11#@ 094010051 TAPPING SCREW B1 4X12 4
12#@ 094010052 TAPPING SCREW B1 4X30 1
13#@ 050200150 O-RING, P15 1
14#@ 050200110 O-RING, P11 1

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 37

 TOOLS

PAGE 38 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 TOOLS
NO. PART NO. PART NAME QTY. REMARKS
1 981010400 CLUTCH PULLER A 1
2 983010060 CLUTCH MOUNTER 1
3 983910090 PISTON ROD HOLDER 1
4 009110044 SOCKET HEAD BOLT 8X50 (FULL THREAD)
CRANK GEAR REMOVER 2
5 983910020 CLUTCH PULLER B 1
6 983010040 SPRING CYLINDER REMOVER 1
7 983910010 PISTON END REMOVER 1

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 39

 ROBIN EH122D46530 — CRANKCASE ASSY.

10

40 50 30
700

830

294

210
295 230 860
298
297
265 75
270 90
280 80
260
250
220
300

NOTE
USE LIQUID GASKET FOR CYLINDER AND INSULATOR GASKET.

PAGE 40 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 ROBIN EH122D46530 — CRANKCASE ASSY.
CRANKCASE ASSY.
NO. PART NO. PART NAME QTY. REMARKS
10 2521030141 CRANKCASE CP...............................................1................INCLUDES ITEMS W/ #
30# 0440250150 OIL SEAL 1
40# 0600250100 BALL BEARING 1
50# 0310060020 DOWEL PIN 2
75# 0440080010 OIL SEAL VC 8X14X4 1
80 0401140030 PLUG 2
90 0211140020 GASKET 2
210 2521110301 MAIN BEARING COVER CP .............................1................INCLUDES ITEMS W/ $
220$ 0440250160 OIL SEAL 1
230$ 0600250010 BALL BEARING 6205C3 1
250 2274500301 GOVERNOR GEAR CP 1
260 2054190103 GOVERNOR SLEEVE 1
265$ 0108100030 STUD 2
270 2686360301 OIL GAUGE CP 1
280 X213160020 GASKET 1
294 2521700201 BRACKET CP (M.B.C) 1
295 2521700101 SUPPORT (M.B.C) 1
297 0011308160 BOLT AND WASHER ASSY 1
298 0011308160 BOLT AND WASHER ASSY 2
300 0130060200 BOLT AND WASHER ASSY 8
700 0310060020 DOWEL PIN 2
830 2681620103 GASKET, BREATHER COVER 1
860 0011306160 BOLT AND WASHER ASSY 2

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 41

 ROBIN EH122D46530 — CYLINDER HEAD ASSY.

710

680 850
MTX80/MTX90 — EH12-2D ROBIN ENGINE— CRANKSHAFT AND PISTON
690
910
726
723
722

720
721

724

725 690 230

220
610 95 240
230 73
20 20 70 72
26 220
630 95
73
72 260

71 240

60 210

900
901
CYLINDER HEAD
60 620 REFERENCE
ONLY

90 80
CRANKCASE
REFERENCE
ONLY

PAGE 42 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 ROBIN EH122D46530 — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO. PART NO. PART NAME QTY. REMARKS
20# 2371420203 VALVE GUIDE O/S 2
26 2771601001 STEM SEAL — E— CRANKSHAFT 1 AND PISTON
60# 0105080480 STUD 2
70# 0105060131 STUD 1
71# 0013906600 STUD 1
72 2533360103 VALVE SPRING 2
73 2693370103 SPRING RETAINER 2
80 2683340103 INTAKE VALVE 1
90 2683350103 EXHAUST VALVE 1
95 13210KA031 COLLET VALVE 4
210 2683530103 PUSH ROD 2
220 2693600103 ROCKER ARM 2
230 2693580103 BOLT, PIVOT 2
240 0170060090 NUT 2
260 2693650103 GUIDE PLATE 1
610 2681310121 CYLINDER HEAD CP ........................................1................INCLUDES ITEMS W/ #
620 2531500133 GASKET, HEAD 1
630 0110080100 FLANGE BOLT 4
680 2521550203 ROCKER COVER 1
690 2691600403 GASKET, ROCKER, COVER 2
710 0110060170 FLANGE BOLT 4
720 2521560120 SPACER ASSY, BREATHER ..............................1................INCLUDES ITEMS W/ $
721$ 2521560113 SPACER, BREATHER 1
722$ 2521600103 LEAF VALVE 1
723$ 2521610103 RETAINER PLATE 1
724$ 2521440123 PLATE 1
725$ 0110060150 FLANGE BOLT 2
726$ 0043506120 SCREW AND WASHER 1
850 2681800503 RUBBER PIPE 1
900 0566000250 CLAMP 1
901 0110060020 FLANGE BOLT 1
910 0561120040 HOSE CLAMP 1

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 43

 ROBIN EH122D46530 — CRANKSHAFT, PISTON ASSY.

370

360 380
350
380

310

50
60

CRANKCASE
REFERENCE
ONLY

70

10

40

320

PAGE 44 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 ROBIN EH122D46530 — CRANKSHAFT, PISTON ASSY.
CRANKSHAFT, PISTON ASSY.
NO. PART NO. PART NAME QTY. REMARKS
10 2682190501 CRANK SHAFT CP 1
40 0230250110 SPACER T=0.6 1
40 0230250120 SPACER T=0.8 1
40 0230250130 SPACER T=1.0 1
50 0021814000 NUT 1
60 0032014000 SPRING WASHER 1
70 0323030010 WOODRUFF KEY 1
310 2522250120 CONNECTING ROD ASSY ...............................1................INCLUDES ITEM W/ #
320# 2362300103 CONNECTING ROD BOLT 2
350 2682330103 PISTON PIN 1
360 26823401H3 PISTON STD 1
360 26823402H3 PISTON O.S. 0.25 1
360 26823403H3 PISTON O.S. 0.5 1
370 2522350117 PISTON RING SET, STD 1
370 2522350217 PISTON RING SET 0.25 O.S. 1
370 2522350317 PISTON RING SET 0.50 O.S. 1
380 2152500403 CLIP 2

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 45

 ROBIN EH122D46530 — CAMSHAFT ASSY.

CRANKCASE
REFERENCE
ONLY

10
36 34 38

50

PAGE 46 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 ROBIN EH122D46530 — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO. PART NO. PART NAME QTY. REMARKS
10 2533170111 CAMSHAFT CP .................................................1................INCLUDES ITEMS W/ #
34# 2273860123 PIN (SPRING) 1
35# 2273640113 RELEASE LEVER 1
36# 0051904100 SPRING PIN 1
37# 0031522000 SNAP RING 1
38# 2273870103 RETURN SPRING 1
50 2393330113 TAPPET 2

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 47

 ROBIN EH122D46530 — RECOIL STARTER ASSY.

10

40
90
95

220
20

207
205
206
249 201

205 203

211 208 202 204

200

PAGE 48 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 ROBIN EH122D46530 — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO. PART NO. PART NAME QTY. REMARKS
10 2525165221 BLOWER HOUSING CP 1
20 920100240 DECAL, (M-MARK) 1
40 0011406550 BOLT AND WASHER ASSY 6X55 4
90 2685270303 HEAD COVER 1
95 0110060140 FLANGE BOLT 2
200 2685020130 RECOIL STARTER ASSY ..................................1................INCLUDES ITEMS W/ #
201# 2705011508 SPIRAL SPRING 1
202# 2695012008 REEL 1
203# 2825011118 STARTER ROPE 1
204# 2615010008 STARTER KNOB 1
205# 2705012508 RATCHET 2
206# 2275013108 FRICTION SPRING 1
207# 2275013508 RETURN SPRING 2
208# 2705026108 RATCHET GUIDE 1
211# 2685014518 STARTER PULLEY 1
220 0110060010 FLANGE BOLT 4
249# 2275015208 SET SCREW 1

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 49

 ROBIN EH122D46530 — CARBURETOR ASSY.
210

918

917 902
947
907
946
945 921 910
948 905 909
949
903 912
929
919 943
917
904 900

906
916
927 908
NOT SOLD SEPARATELY
920
926
925
915

911

914

901
916

PAGE 50 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 ROBIN EH122D46530 — CARBURETOR ASSY.
CARBURETOR ASSY.
MTX80: S/N T-4419 AND BELOW
MTX90: S/N T-1341 AND BELOW
NO. PART NO. PART NAME QTY. REMARKS
210 2526257100 CARBURETOR ASSY ...................................... 1 ............... INCLUDES ITEMS W/ #
900# 5016004010 SCREEN INLET 1
901# 2526260508 COVER, METALING DIAPHRAGM 1
902# 2526260408 COVER PUMP 1
903# 2526261208 THROTTLE SHAFT 1
904# 1616233508 VALVE THROTTLE 1
905# 2846260308 SHAFT ASSY CHOKE 1
906# 5106045040 CLIP 1
907# 2846260408 VALVE, CHOKE 1
908# 1616255208 VALVE, INLET NEEDLE 1
909# 1476258408 BALL 1
910# 1616238008 GASKET PLUG 1
911# 1616238108 GASKET, METALING DIAPHRAGM 1
912# 2526261008 DIAPHRAGM PUMP 1
914# 1616238308 DIAPHRAGM ASSY, METALING 1
915# 1066257508 SCREW 1
916# 1066257608 SCREW ASSY 5
917# 1476257308 SCREW 2
918# 2846260008 SCREW 1
919# 1616245408 SPRING, IDLE ADJUST 1
920# 1616245108 SPRING, METALING LEVER 1
921# 1476258308 SPRING, CHOKE 1
925# 1616236808 PIN, METALING LEVER 1
926# 1616236908 LEVER, METALING 1
927# 1476257508 PLUG 1
929# 1616238508 SCREW, IDLE ADJUST 1
943# 2526261108 SPRING PUMP 1
945# 1616255108 STOPPER, THROTTLE 1
946# 2526260308 LEVER, THROTTLE 1
947# 1616255308 SCREW VALVE 2
948# 2526260208 SPACER, THROTTLE LEVER 1
949# 2526260108 WASHER 1

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 51

 ROBIN EH122D46530 — CARBURETOR ASSY.

PAGE 52 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 ROBIN EH122D46530 — CARBURETOR ASSY.
CARBURETOR ASSY.
MTX80: S/N T-4420 AND ABOVE
MTX90: S/N T-1342 AND ABOVE
NO. PART NO. PART NAME QTY. REMARKS
210 2526257300 CARBURETOR ASSY 1 INCLUDES ITEMS W/ #
900# 5016004010 SCREEN INLET 1
901# 2526261608 COVER, PRIMER PUMP 1
902# 2526261308 COVER PUMP 1
903# 2526261208 THROTTLE SHAFT 1
904# 1616233508 VALVE THROTTLE 1
905# 2846260308 SHAFT ASSY CHOKE 1
906# 5106045040 CLIP 1
907# 2846260408 VALVE, CHOKE 1
908# 1616255208 VALVE, INLET NEEDLE 1
909# 1476258408 BALL 1
910# 1616238008 GASKET PLUG 1
911# 2526261808 GASKET, METALING DIAPHRAGM 1
912# 2526261008 DIAPHRAGM PUMP 1
914# 2526261708 DIAPHRAGM ASSY, METALING 1
915# 2526261908 SCREW 1
916# 2526262008 SCREW ASSY 5
917# 1476257308 SCREW 2
918# 2846260008 SCREW 1
919# 1616245408 SPRING, IDLE ADJUST 1
920# 1616245108 SPRING, METALING LEVER 1
921# 1476258308 SPRING, CHOKE 1
925# 1616236808 PIN, METALING LEVER 1
926# 1616236908 LEVER, METALING 1
927# 1476257508 PLUG 1
929# 1616238508 SCREW, IDLE ADJUST 1
943# 2526261108 SPRING PUMP 1
945# 1616255108 STOPPER, THROTTLE 1
946# 2526260308 LEVER, THROTTLE 1
947# 1616255308 SCREW VALVE 2
948# 2526260208 SPACER, THROTTLE LEVER 1
949# 1476258600 SEAL, DUST 2
950# 1066257608 SCREW ASSY 1
961# 2526261408 BODY ASSY, AIR PURGE 1
962# 2526261508 PUMP, PRIMER 1

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 53

 ROBIN EH122D46530 — AIR CLEANER ASSY.

590
556 552
555
567

500
550
565
CYLINDER HEAD 528
REFERENCE
ONLY
563

560
570
530

PAGE 54 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 ROBIN EH122D46530 — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO. PART NO. PART NAME QTY. REMARKS
500 2683300413 INTAKE PIPE 1
528 2683660103 PLATE 1
530 2843810103 INTAKE PIPE 1
550 1573500103 GASKET, INSULATOR 1
552 2843650103 GASKET (INTAKE) 1
555 2823590103 GASKET, INSULATOR 1
556 0011406400 BOLT AND WASHER ASSY 1
560 1066500203 GASKET (CARB.) 2
563 0119060090 BOLT (SOCKET HEAD) 2
565 2843310103 INTAKE FLANGE CP 1
567 0100050110 BOLT M5X0.8X70L 2
570 0176050010 SELF LOCK NUT 2
590 0023806000 FLANGE NUT 2

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 55

 ROBIN EH122D46530 — MUFFLER ASSY.

366
340
310 345
340
CYLINDER HEAD
REFERENCE
ONLY

350
330

365

CRANKCASE
REFERENCE
ONLY

PAGE 56 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 ROBIN EH122D46530 — MUFFLER ASSY.
MUFFLER ASSY.
NO. PART NO. PART NAME QTY. REMARKS
310 2523040111 MUFFLER CP 1
330 2523700111 BRACKET CP 1
340 2533520103 GASKET, MUFFLER 2
345 2523650123 SPACER, EXHAUST 1
350 0176080020 SELF LOCK NUT 2
365 0011308160 BOLT AND WASHER ASSY 2
366 0011408160 BOLT AND WASHER 8X16 2

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 57

 ROBIN EH122D46530 — GOVERNOR ASSY.

40

30
20
80
280

50 26 200
70
210 230
240

60 716
710
10

231
235
715

290
293

PAGE 58 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 ROBIN EH122D46530 — GOVERNOR ASSY.
GOVERNOR ASSY.
NO. PART NO. PART NAME QTY. REMARKS
10 2524230303 GOVERNOR LEVER CP 1
20 2274220103 GOVERNOR SHAFT 1
26 0031108000 WASHER 1
30 2544270101 GOVERNOR ROD CP 1
40 2544280103 ROD SPRING 1
50 0031306000 CLIP 2
60 0011406300 BOLT AND WASHER ASSY 1
70 0186060020 NUT 1
80 2524250323 GOVERNOR SPRING 1
200 2524340230 SPEED CONTROL ASSY 1
210 0116040030 BOLT 1
230 0043105250 SCREW, PANHEAD 1
231 0043104250 SCREW 1
235 2684500113 CONTROL SPRING 1
240 0021705000 NUT 1
280 2264310101 LINK PIVOT CP 1
290 2684420201 WIRE BRACKET 1
293 0110060030 FLANGE BOLT 1
710 2524280111 PROTECTOR CP, GOVERNOR 1
715 0011308160 BOLT AND WASHER ASSY 1
716 0110060030 FLANGE BOLT 1

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 59

 ROBIN EH122D46530 — FLYWHEEL IGNITION ASSY.

11
30
95
110

10
90
70

100

11

10

PAGE 60 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 ROBIN EH122D46530 — FLYWHEEL IGNITION ASSY.
FLYWHEEL IGNITION ASSY.
NO. PART NO. PART NAME QTY. REMARKS
10 2687933201 FLYWHEEL CP 1
11 2697943011 IGNITION COIL CP 1
30 0011406250 BOLT AND WASHER ASSY 2
70 0150040090 TAPPING SCREW 2
90 0566000250 CLAMP 1
95 0659000010 PLUG TERMINAL 1
100 0650140580 SPARK PLUG BR6ES 1
110 2307510113 SPARK PLUG CAP 1

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 61

 ROBIN EH122D46530 — LABELS AND ACCESSORIES

LABELS

100

101

102

103

ACCESSORIES

201

202

PAGE 62 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 ROBIN EH122D46530 — LABELS AND ACCESSORIES
LABELS AND ACCESSORIES
NO. PART NO. PART NAME QTY. REMARKS
100 0732004450 LABEL, CAUTION 1
101 0732004520 LABEL, OIL CAUTION 1
102 0732003900 LABEL, WARNING 1
103 0732005020 LABEL CHOKE 1
201 0830000010 COIL SPRING 1
202 2267510103 CLAMP 1

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 63

 TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS 5. Parts must be in new and resalable Multiquip reserves the right to quote and
Terms of payment for parts are net 30 days. condition, in the original Multiquip sell direct to Government agencies, and to
package (if any), and with Multiquip part Original Equipment Manufacturer accounts
FREIGHT POLICY numbers clearly marked. who use our products as integral parts of their
6. The following items are not returnable: own products.
All parts orders will be shipped collect or
prepaid with the charges added to the invoice. a. Obsolete parts. (If an item is in the SPECIAL EXPEDITING SERVICE
All shipments are F.O.B. point of origin. price book and shows as being
Multiquip’s responsibility ceases when a A $35.00 surcharge will be added to the
replaced by another item, it is
signed manifest has been obtained from the invoice for special handling including bus
obsolete.)
carrier, and any claim for shortage or damage shipments, insured parcel post or in cases
b. Any parts with a limited shelf life where Multiquip must personally deliver the
must be settled between the consignee and
(such as gaskets, seals, “O” rings, parts to the carrier.
the carrier.
and other rubber parts) that were
MINIMUM ORDER purchased more than six months LIMITATIONS OF SELLER’S LIABILITY
prior to the return date. Multiquip shall not be liable hereunder for
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for c. Any line item with an extended damages in excess of the purchase price of
instructions regarding handling of orders not dealer net price of less than the item with respect to which damages are
meeting this requirement. $5.00. claimed, and in no event shall Multiquip be
d. Special order items. liable for loss of profit or good will or for any
RETURNED GOODS POLICY other special, consequential or incidental
e. Electrical components. damages.
Return shipments will be accepted and
credit will be allowed, subject to the following f. Paint, chemicals, and lubricants.
LIMITATION OF WARRANTIES
provisions: g. Decals and paper products.
No warranties, express or implied, are
1. A Returned Material Authorization h. Items purchased in kits. made in connection with the sale of parts or
must be approved by Multiquip prior to 7. The sender will be notified of any material trade accessories nor as to any engine not
shipment. received that is not acceptable. manufactured by Multiquip. Such warranties
2. To obtain a Return Material Authorization, 8. Such material will be held for five made in connection with the sale of new,
a list must be provided to Multiquip working days from notification, pending complete units are made exclusively by a
Parts Sales that defines item numbers, instructions. If a reply is not received statement of warranty packaged with such
quantities, and descriptions of the items within five days, the material will be units, and Multiquip neither assumes nor
to be returned. returned to the sender at his expense. authorizes any person to assume for it
any other obligation or liability whatever in
a. The parts numbers and descriptions 9. Credit on returned parts will be issued
connection with the sale of its products. Apart
must match the current parts price at dealer net price at time of the original
from such written statement of warranty,
list. purchase, less a 15% restocking
there are no warranties, express, implied or
b. The list must be typed or computer charge.
statutory, which extend beyond the description
generated. 10. In cases where an item is accepted, for of the products on the face hereof.
c. The list must state the reason(s) which the original purchase document
for the return. can not be determined, the price will be
based on the list price that was effective Effective: February 22, 2006
d. The list must reference the sales twelve months prior to the RMA date.
order(s) or invoice (s) under
which the items were originally 11. Credit issued will be applied to future
purchased. purchases only.
e. The list must include the name PRICING AND REBATES
and phone number of the person Prices are subject to change without prior
requesting the RMA. notice. Price changes are effective on a
3. A copy of the Return Material Authorization specific date and all orders received on or
must accompany the return shipment. after that date will be billed at the revised price.
Rebates for price declines and added charges
4. Freight is at the sender’s expense. All for price increases will not be made for stock
parts must be returned freight prepaid to on hand at the time of any price change.
Multiquip’s designated receiving point.

PAGE 64 — MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11)

 NOTES
NOTES

MTX80/90 RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (1/14/11) — PAGE 65

 OPERATION AND PARTS MANUAL

HERE’S HOW TO GET HELP

PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office MQ Parts Department
18910 Wilmington Ave. Tel. (800) 421-1244 800-427-1244 Fax: 800-672-7877
Carson, CA 90746 Fax (800) 537-3927 310-537-3700 Fax: 310-637-3284
Contact: mq@multiquip.com
Service Department Warranty Department
800-421-1244 Fax: 310-537-4259 800-421-1244 Fax: 310-943-2249
310-537-3700 310-537-3700
Technical Assistance
800-478-1244 Fax: 310-943-2238
MEXICO UNITED KINGDOM
MQ Cipsa Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5 Tel: (52) 222-225-9900 Unit 2, Northpoint Industrial Estate, Tel: 0161 339 2223
Momoxpan, Cholula, Puebla 72760 Mexico Fax: (52) 222-285-0420 Globe Lane, Fax: 0161 339 3226
Contact: pmastretta@cipsa.com.mx Dukinfield, Cheshire SK16 4UJ
Contact: sales@multiquip.co.uk
CANADA
Multiquip
4110 Industriel Boul. Tel: (450) 625-2244
Laval, Quebec, Canada H7L 6V3 Tel: (877) 963-4411
Contact: jmartin@multiquip.com Fax: (450) 625-8664

© COPYRIGHT 2011, MULTIQUIP INC.

Multiquip Inc, the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks
are the property of their respective owners and used with permission.

This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.

The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.

Your Local Dealer is: