LM324-N-MIL Low-Power, Quad-Operational Amplifier: 1 Features 3 Description

Product Order Technical Tools & Support &
Folder Now Documents Software Community
LM324-N-MIL
SNOSD66 – JUNE 2017
LM324-N-MIL Low-Power, Quad-Operational Amplifier

1 Features 3 Description
•
1 Internally Frequency Compensated for Unity Gain The LM324-N-MIL device consists of four
independent, high-gain, internally frequency
• Large DC Voltage Gain 100 dB compensated operational amplifiers designed to
• Wide Bandwidth (Unity Gain) 1 MHz operate from a single power supply over a wide range
(Temperature Compensated) of voltages. Operation from split-power supplies is
• Wide Power Supply Range: also possible and the low-power supply current drain
is independent of the magnitude of the power supply
– Single Supply 3 V to 32 V voltage.
– or Dual Supplies ±1.5 V to ±16 V
Application areas include transducer amplifiers, DC
• Very Low Supply Current Drain (700 μA) gain blocks and all the conventional op amp circuits
—Essentially Independent of Supply Voltage which now can be more easily implemented in single
• Low Input Biasing Current 45 nA power supply systems. For example, the LM324-N-
(Temperature Compensated) MIL device can directly operate off of the standard 5-
• Low Input Offset Voltage 2 mV V power supply voltage which is used in digital
systems and easily provides the required interface
and Offset Current: 5 nA
electronics without requiring the additional ±15 V
• Input Common-Mode Voltage Range Includes power supplies.
Ground
• Differential Input Voltage Range Equal to the Device Information(1)
Power Supply Voltage PART NUMBER PACKAGE BODY SIZE (NOM)
• Large Output Voltage Swing 0 V to V+ − 1.5 V CDIP (14) 19.56 mm × 6.67 mm
• Advantages: PDIP (14) 19.177 mm × 6.35 mm
LM324-N-MIL
– Eliminates Need for Dual Supplies SOIC (14) 8.65 mm × 3.91 mm
TSSOP (14) 5.00 mm × 4.40 mm
– Four Internally Compensated Op Amps in a
Single Package (1) For all available packages, see the orderable addendum at
the end of the data sheet.
– Allows Direct Sensing Near GND and VOUT
also Goes to GND Schematic Diagram
– Compatible With All Forms of Logic
– Power Drain Suitable for Battery Operation
– In the Linear Mode the Input Common-Mode,
Voltage Range Includes Ground and the
Output Voltage
– Can Swing to Ground, Even Though Operated
from Only a Single Power Supply Voltage
– Unity Gain Cross Frequency is Temperature
Compensated
– Input Bias Current is Also Temperature
Compensated
2 Applications
• Transducer Amplifiers
• DC Gain Blocks
• Conventional Op Amp Circuits
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM324-N-MIL
SNOSD66 – JUNE 2017 www.ti.com
Table of Contents
1 Features .................................................................. 1 7.4 Device Functional Modes.......................................... 8
2 Applications ........................................................... 1 8 Application and Implementation ........................ 10
3 Description ............................................................. 1 8.1 Application Information............................................ 10
4 Revision History..................................................... 2 8.2 Typical Applications ............................................... 10
5 Pin Configuration and Functions ......................... 3 9 Power Supply Recommendations...................... 20
6 Specifications......................................................... 4 10 Layout................................................................... 20
6.1 Absolute Maximum Ratings ...................................... 4 10.1 Layout Guidelines ................................................. 20
6.2 ESD Ratings.............................................................. 4 10.2 Layout Example .................................................... 20
6.3 Recommended Operating Conditions....................... 4 11 Device and Documentation Support ................. 21
6.4 Thermal Information .................................................. 4 11.1 Receiving Notification of Documentation Updates 21
6.5 Electrical Characteristics........................................... 5 11.2 Community Resources.......................................... 21
6.6 Typical Characteristics .............................................. 6 11.3 Trademarks ........................................................... 21
7 Detailed Description .............................................. 8 11.4 Electrostatic Discharge Caution ............................ 21
7.1 Overview ................................................................... 8 11.5 Glossary ................................................................ 21
7.2 Functional Block Diagram ......................................... 8 12 Mechanical, Packaging, and Orderable
7.3 Feature Description................................................... 8 Information ........................................................... 21
4 Revision History
DATE REVISION NOTES
June 2017 * Initial release.
2 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated
Product Folder Links: LM324-N-MIL

LM324-N-MIL
www.ti.com SNOSD66 – JUNE 2017
5 Pin Configuration and Functions
J Package
14-Pin CDIP
Top View
D Package
14-Pin SOIC
Top View
Pin Functions
PIN
TYPE DESCRIPTION
NAME NO.
OUTPUT1 1 O Output, Channel 1
INPUT1- 2 I Inverting Input, Channel 1
INPUT1+ 3 I Noninverting Input, Channel 1
V+ 4 P Positive Supply Voltage
INPUT2+ 5 I Nonnverting Input, Channel 2
GND 11 P Ground or Negative Supply Voltage
Copyright © 2017, Texas Instruments Incorporated Submit Documentation Feedback 3

LM324-N-MIL
6 Specifications
6.1 Absolute Maximum Ratings
(1)
See .
MIN MAX UNIT
Supply Voltage, V+ 32 V
Differential Input Voltage 32 V
Input Voltage −0.3 32 V
Input Current (VIN < −0.3 V) (2) 50 mA
Power Dissipation (3) PDIP 1130 mW
CDIP 1260 mW
SOIC Package 800 mW
Output Short-Circuit to GND (One
V+ ≤ 15 V and TA = 25°C Continuous
Amplifier) (4)
Dual-In-Line Soldering (10 seconds) 260 °C
Package
Soldering Information
Small Outline Vapor Phase (60 seconds) 215 °C
Package Infrared (15 seconds) 220 °C
Storage temperature, Tstg –65 150 °C
(1) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(2) This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of
the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is
also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the op amps to go to
the V+voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and
normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than −0.3 V (at 25°C).
(3) For operating at high temperatures, the LM324-N-MIL must be derated based on a 125°C maximum junction temperature and a thermal
resistance of 88°C/W which applies for the device soldered in a printed circuit board, operating in a still air ambient. The dissipation is
the total of all four amplifiers—use external resistors, where possible, to allow the amplifier to saturate of to reduce the power which is
dissipated in the integrated circuit.
(4) Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of 15 V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.
6.2 ESD Ratings

VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) ±250 V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MIN MAX UNIT
Supply Voltage (V+ - V-) 3 32 V
Operating Input Voltage on Input pins 0 V+ V
Operating junction temperature, TJ 0 70 °C
6.4 Thermal Information

LM324-N-MIL
THERMAL METRIC (1) D/SOIC UNIT
14 PINS
RθJA Junction-to-ambient thermal resistance 88 °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.

LM324-N-MIL
6.5 Electrical Characteristics

V+ = +5.0V, (1)
, unless otherwise stated
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Input Offset Voltage TA = 25°C (2) 2 7 mV
Input Bias Current (3) IIN(+) or IIN(−), VCM = 0 V, TA = 25°C 45 250 nA
Input Offset Current IIN(+) or IIN(−), VCM = 0 V, TA = 25°C 5 50 nA
V+ = 30 V,
Input Common-Mode Voltage Range (4) 0 V+−1.5 V
TA = 25°C
Over Full Temperature Range
RL = ∞ On All Op Amps, 1.5 3
Supply Current V+ = 30 V mA
+ 0.7 1.2
V =5V
V+ = 15V, RL≥ 2 kΩ,
Large Signal Voltage Gain 25 100 V/mV
(VO = 1 V to 11 V), TA = 25°C
Common-Mode Rejection Ratio DC, VCM = 0 V to V+ − 1.5 V, TA = 25°C 65 85 dB
Power Supply Rejection Ratio V+ = 5 V to 30 V, TA = 25°C 65 100 dB
Amplifier-to-Amplifier f = 1 kHz to 20 kHz, TA = 25°C
−120 dB
Coupling (5) (Input Referred)
VIN+ = 1 V, VIN− = 0 V,
Source 20 40 mA
V+ = 15 V, VO = 2 V, TA = 25°C
VIN− = 1 V, VIN+ = 0 V,
Output Current 10 20 mA
V+ = 15 V, VO = 2 V, TA = 25°C
Sink
VIN− = 1 V, VIN+ = 0 V,
12 50 µA
V+ = 15 V, VO = 200 mV, TA = 25°C
Short Circuit to Ground V+ = 15 V, TA = 25°C (6) 40 60 mA
(2)
Input Offset Voltage See 9 mV
VOS Drift RS = 0 Ω 7 µV/°C
Input Offset Current IIN(+) − IIN(−), VCM = 0 V 150 nA
IOS Drift RS = 0 Ω 10 pA/°C
Input Bias Current IIN(+) or IIN(−) 40 500 nA
Input Common-Mode Voltage Range (4) +
V = 30 V 0 +
V −2 V
+
V = 15 V (VOSwing = 1V to 11V),
Large Signal Voltage Gain 15 V/mV
RL ≥ 2 kΩ
RL = 2 kΩ 26
Output Voltage VOH V+ = 30 V V
RL = 10 kΩ 27 28
Swing
VOL V+ = 5 V, RL = 10 kΩ 5 20 mV
VIN+
= 1 V,
Source VO = 2 V VIN−
= 0 V, 10 20 mA
+
V = 15 V
Output Current
VIN− = 1 V,
Sink VIN+ = 0 V, 5 8 mA
V+ = 15 V
(1) The LM324-N-MIL temperature specifications are limited to 0°C ≤ TA ≤ +70°C.

(2) VO ≃ 1.4V, RS = 0 Ω with V+ from 5 V to 30 V.
(3) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
(4) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3 V (at 25°C). The
upper end of the common-mode voltage range is V+ − 1.5 V (at 25°C), but either or both inputs can go to 32 V without damage,
independent of the magnitude of V+.
(5) Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This
typically can be detected as this type of capacitance increases at higher frequencies.
(6) Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of 15 V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.

LM324-N-MIL
6.6 Typical Characteristics
Figure 1. Input Voltage Range Figure 2. Input Current
Figure 3. Supply Current Figure 4. Voltage Gain
Figure 5. Open-Loop Frequency Response Figure 6. Common Mode Rejection Ratio

LM324-N-MIL
Typical Characteristics (continued)
Figure 7. Voltage Follower Pulse Response Figure 8. Voltage Follower Pulse Response (Small Signal)
Figure 9. Large Signal Frequency Response Figure 10. Output Characteristics Current Sourcing
Figure 11. Output Characteristics Current Sinking Figure 12. Current Limiting

LM324-N-MIL
7 Detailed Description
7.1 Overview
The LM324-N-MIL device is an op amp which operates with only a single power supply voltage, has true-
differential inputs, and remains in the linear mode with an input common-mode voltage of 0 VDC. This amplifier
operates over a wide range of power supply voltage with little change in performance characteristics. At 25°C
amplifier operation is possible down to a minimum supply voltage of 2.3 VDC.
7.2 Functional Block Diagram
7.3 Feature Description

The LM324-N-MIL provides a compelling balance of performance versus current consumption. The 700 μA of
supply current draw over the wide operating conditions with a 1-MHz gain-bandwidth and temperature
compensated bias currents makes the LM324-N-MIL an effective solution for large variety of applications. The
input offset voltage of 2 mV and offset current of 5 nA, along with the 45n-A bias current across a wide supply
voltage means a single design can be used in a large number of different implementations.
7.4 Device Functional Modes

Large differential input voltages can be easily accommodated and, as input differential voltage protection diodes
are not needed, no large input currents result from large differential input voltages. The differential input voltage
may be larger than V+ without damaging the device. Protection should be provided to prevent the input voltages
from going negative more than −0.3 VDC (at 25°C). An input clamp diode with a resistor to the IC input terminal
can be used.
To reduce the power supply drain, the amplifiers have a class A output stage for small signal levels which
converts to class B in a large signal mode. This allows the amplifiers to both source and sink large output
currents. Therefore both NPN and PNP external current boost transistors can be used to extend the power
capability of the basic amplifiers. The output voltage needs to raise approximately 1 diode drop above ground to
bias the on-chip vertical PNP transistor for output current sinking applications.
For ac applications, where the load is capacitively coupled to the output of the amplifier, a resistor should be
used, from the output of the amplifier to ground to increase the class A bias current and prevent crossover
distortion.
Where the load is directly coupled, as in dc applications, there is no crossover distortion.
Capacitive loads which are applied directly to the output of the amplifier reduce the loop stability margin. Values
of 50 pF can be accommodated using the worst-case non-inverting unity gain connection. Large closed loop
gains or resistive isolation should be used if larger load capacitance must be driven by the amplifier.

LM324-N-MIL
Device Functional Modes (continued)

The bias network of the LM324-N-MIL establishes a drain current which is independent of the magnitude of the
power supply voltage over the range of from 3 VDC to 30 VDC.
Output short circuits either to ground or to the positive power supply should be of short time duration. Units can
be destroyed, not as a result of the short circuit current causing metal fusing, but rather due to the large increase
in IC chip dissipation which will cause eventual failure due to excessive junction temperatures. Putting direct
short-circuits on more than one amplifier at a time will increase the total IC power dissipation to destructive
levels, if not properly protected with external dissipation limiting resistors in series with the output leads of the
amplifiers. The larger value of output source current which is available at 25°C provides a larger output current
capability at elevated temperatures (see Typical Characteristics) than a standard IC op amp.

LM324-N-MIL
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information

The LM324-N-MIL amplifier is specified for operation from 3 V to 32 V (±1.5 V to ±16 V). Many of the
specifications apply from –40°C to 125°C. Parameters that can exhibit significant variance with regards to
operating voltage or temperature are presented in Typical Characteristics.
8.2 Typical Applications

Figure 13 emphasizes operation on only a single power supply voltage. If complementary power supplies are
available, all of the standard op amp circuits can be used. In general, introducing a pseudo-ground (a bias
voltage reference of V+/2) will allow operation above and below this value in single power supply systems. Many
application circuits are shown which take advantage of the wide input common-mode voltage range which
includes ground. In most cases, input biasing is not required and input voltages which range to ground can easily
be accommodated.
8.2.1 Non-Inverting DC Gain (0 V Input = 0 V Output)
*R not needed due to temperature independent IIN
Figure 13. Non-Inverting Amplifier with G = 100
8.2.1.1 Design Requirements

For this example application, the required signal gain is a non-inverting 100x±5% with a supply voltage of 5 V.
8.2.1.2 Detailed Design Procedure

Using the equation for a non-inverting gain configuration, Av = 1+R2/R1. Setting the R1 to 10 kΩ, R2 is 99 times
larger than R1, which is 990 kΩ. A 1MΩ is more readily available, and provides a gain of 101, which is within the
desired specification.

LM324-N-MIL
Typical Applications (continued)

The gain-frequency characteristic of the amplifier and its feedback network must be such that oscillation does not
occur. To meet this condition, the phase shift through amplifier and feedback network must never exceed 180°
for any frequency where the gain of the amplifier and its feedback network is greater than unity. In practical
applications, the phase shift should not approach 180° since this is the situation of conditional stability. Obviously
the most critical case occurs when the attenuation of the feedback network is zero.
8.2.1.3 Application Curve
Figure 14. Non-Inverting Amplified Response Curve

LM324-N-MIL

8.2.2 Other Application Circuits at V+ = 5.0 VDC
Where: V0 = V1 + V2 − V3 − V4 Where: V0 = 0 VDC for VIN = 0 VDC

(V1 + V2) ≥ (V3 + V4) to keep VO > 0 VDC AV = 10
Figure 15. DC Summing Amplifier Figure 16. Power Amplifier

(VIN'S ≥ 0 VDC And VO ≥ VDC)
fo = 1 kHz Q = 50 AV = 100 (40 dB)
Figure 17. LED Driver Figure 18. “BI-QUAD” RC Active Bandpass Filter

LM324-N-MIL
Figure 19. Fixed Current Sources
*(Increase R1 for IL small)
Figure 20. Lamp Driver Figure 21. Current Monitor
Figure 22. Driving TTL Figure 23. Voltage Follower

LM324-N-MIL
Figure 24. Pulse Generator Figure 25. Squarewave Oscillator
IO = 1 amp/volt VIN (Increase RE for Io small)
Figure 26. Pulse Generator Figure 27. High Compliance Current Sink

LM324-N-MIL
Figure 28. Low Drift Peak Detector Figure 29. Comparator With Hysteresis
*Wide control voltage range:

0 VDC ≤ VC ≤ 2 (V+ −1.5 VDC)
VO = VR
Figure 30. Ground Referencing a Differential Input Figure 31. Voltage Controlled Oscillator Circuit
Signal

LM324-N-MIL
Q=1 AV = 2
Figure 32. Photo Voltaic-Cell Amplifier Figure 33. DC Coupled Low-Pass RC Active Filter
Figure 34. AC Coupled Inverting Amplifier
Figure 35. AC Coupled Non-Inverting Amplifier

LM324-N-MIL
Figure 36. High Input Z, DC Differential Amplifier
Figure 37. High Input Z Adjustable-Gain DC Instrumentation Amplifier

LM324-N-MIL
Figure 38. Bridge Current Amplifier
Figure 39. Using Symmetrical Amplifiers to Reduce Input Current (General Concept)

LM324-N-MIL
fO = 1 kHz Q = 25
Figure 40. Bandpass Active Filter

LM324-N-MIL
9 Power Supply Recommendations

The pinouts of the package have been designed to simplify PC board layouts. Inverting inputs are adjacent to
outputs for all of the amplifiers and the outputs have also been placed at the corners of the package (pins 1, 7, 8,
and 14).
Precautions should be taken to insure that the power supply for the integrated circuit never becomes reversed in
polarity or that the unit is not inadvertently installed backwards in a test socket as an unlimited current surge
through the resulting forward diode within the IC could cause fusing of the internal conductors and result in a
destroyed unit.
10 Layout
10.1 Layout Guidelines

The V + pin should be bypassed to ground with a low-ESR capacitor. The optimum placement is closest to the V
+ and ground pins.
Take care to minimize the loop area formed by the bypass capacitor connection between V + and ground.
The ground pin should be connected to the PCB ground plane at the pin of the device.
The feedback components should be placed as close to the device as possible minimizing strays.
10.2 Layout Example
GND
GND
GND
VIND
GND
VINC
2 2 2 2
GND VOUTA VOUTD GND
VOUTA 1: VOUTA 14: VOUTD VOUTD
1
VINA 1 1 1 1 1
IN-A IN-A 13: IN-D IN-D IN-D VIND
IN-A 2: IN-A IN-D
2
IN+A 2
IN+A 3: IN+A 12: IN+D IN+D
IN+D
1 2
GND
GND V+
V+ 4: V+ 11: GND GND
NC
VI
2 1
2 IN+B 5: IN+B 10: IN+C IN+C
IN+C VINC
VINC
IN+B
1 1 IN-B 6: IN-B 9: IN-C IN-C 1 1

1 IN-B IN-B IN-C IN-C
VOUTA
VINB
VOUTD
VOUTB 7: VOUTB 8: VOUTC VOUTC

2 2 2 2
GND VOUTB VOUTC GND
GND
GND GND
Figure 41. Layout Example

LM324-N-MIL
11 Device and Documentation Support
11.1 Receiving Notification of Documentation Updates

To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.2 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.3 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
11.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

PACKAGE OPTION ADDENDUM
www.ti.com 30-Sep-2021
PACKAGING INFORMATION
Orderable Device Status Package Type Package Pins Package Eco Plan Lead finish/ MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) Ball material (3) (4/5)
(6)
LM324J ACTIVE CDIP J 14 25 Non-RoHS Call TI Level-1-NA-UNLIM 0 to 70 LM324J

& Green
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com 5-Jan-2022
TUBE
*All dimensions are nominal

Device Package Name Package Type Pins SPQ L (mm) W (mm) T (µm) B (mm)
LM324J J CDIP 14 25 502 14 11938 4.32
Pack Materials-Page 1
PACKAGE OUTLINE
J0014A SCALE 0.900
CDIP - 5.08 mm max height
CERAMIC DUAL IN LINE PACKAGE
PIN 1 ID A 4X .005 MIN

(OPTIONAL) [0.13] .015-.060 TYP
[0.38-1.52]
1
14
12X .100
[2.54] 14X .014-.026
14X .045-.065 [0.36-0.66]
[1.15-1.65]
.010 [0.25] C A B
.754-.785
[19.15-19.94]
7 8
B .245-.283 .2 MAX TYP .13 MIN TYP

[6.22-7.19] [5.08] [3.3]
C SEATING PLANE
.308-.314
[7.83-7.97]
AT GAGE PLANE
.015 GAGE PLANE

[0.38]
0 -15 14X .008-.014

TYP [0.2-0.36]
4214771/A 05/2017
NOTES:
1. All controlling linear dimensions are in inches. Dimensions in brackets are in millimeters. Any dimension in brackets or parenthesis are for
reference only. Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This package is hermitically sealed with a ceramic lid using glass frit.
4. Index point is provided on cap for terminal identification only and on press ceramic glass frit seal only.
5. Falls within MIL-STD-1835 and GDIP1-T14.
www.ti.com
EXAMPLE BOARD LAYOUT
J0014A CDIP - 5.08 mm max height
CERAMIC DUAL IN LINE PACKAGE
(.300 ) TYP
[7.62] SEE DETAIL B
SEE DETAIL A
1 14
12X (.100 )
[2.54]
SYMM
14X ( .039)
[1]
7 8
SYMM
LAND PATTERN EXAMPLE

NON-SOLDER MASK DEFINED
SCALE: 5X
.002 MAX (.063)

[0.05] [1.6]
ALL AROUND METAL
( .063)
SOLDER MASK [1.6]
OPENING
METAL
SOLDER MASK .002 MAX

(R.002 ) TYP [0.05]
OPENING
[0.05] ALL AROUND
DETAIL A DETAIL B
SCALE: 15X 13X, SCALE: 15X
4214771/A 05/2017
www.ti.com
MECHANICAL DATA
N0014A
NFF0014A
N14A (Rev G)
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated

LM324-N-MIL Low-Power, Quad-Operational Amplifier: 1 Features 3 Description

Uploaded by

Copyright:

Available Formats

LM324-N-MIL Low-Power, Quad-Operational Amplifier: 1 Features 3 Description

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LM324-N-MIL Low-Power, Quad-Operational Amplifier: 1 Features 3 Description

Uploaded by

Copyright:

Available Formats

Product Order Technical Tools & Support &

Folder Now Documents Software Community

LM324-N-MIL Low-Power, Quad-Operational Amplifier

2 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated

Product Folder Links: LM324-N-MIL

5 Pin Configuration and Functions

Copyright © 2017, Texas Instruments Incorporated Submit Documentation Feedback 3

6.2 ESD Ratings

6.3 Recommended Operating Conditions

6.4 Thermal Information

4 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated

Product Folder Links: LM324-N-MIL

6.5 Electrical Characteristics

(1) The LM324-N-MIL temperature specifications are limited to 0°C ≤ TA ≤ +70°C.

Copyright © 2017, Texas Instruments Incorporated Submit Documentation Feedback 5

6.6 Typical Characteristics

Figure 1. Input Voltage Range Figure 2. Input Current

Figure 3. Supply Current Figure 4. Voltage Gain

Figure 5. Open-Loop Frequency Response Figure 6. Common Mode Rejection Ratio

6 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated

Product Folder Links: LM324-N-MIL

Typical Characteristics (continued)

Copyright © 2017, Texas Instruments Incorporated Submit Documentation Feedback 7

7.2 Functional Block Diagram

7.3 Feature Description

7.4 Device Functional Modes

8 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated

Product Folder Links: LM324-N-MIL

Device Functional Modes (continued)

Copyright © 2017, Texas Instruments Incorporated Submit Documentation Feedback 9

8 Application and Implementation

8.1 Application Information

8.2 Typical Applications

8.2.1 Non-Inverting DC Gain (0 V Input = 0 V Output)

*R not needed due to temperature independent IIN

Figure 13. Non-Inverting Amplifier with G = 100

8.2.1.1 Design Requirements

8.2.1.2 Detailed Design Procedure

10 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated

Product Folder Links: LM324-N-MIL

Typical Applications (continued)

8.2.1.3 Application Curve

Figure 14. Non-Inverting Amplified Response Curve

Copyright © 2017, Texas Instruments Incorporated Submit Documentation Feedback 11

Typical Applications (continued)

Where: V0 = V1 + V2 − V3 − V4 Where: V0 = 0 VDC for VIN = 0 VDC

Figure 15. DC Summing Amplifier Figure 16. Power Amplifier

fo = 1 kHz Q = 50 AV = 100 (40 dB)

12 Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated

Product Folder Links: LM324-N-MIL

Typical Applications (continued)

Figure 19. Fixed Current Sources

*(Increase R1 for IL small)

Figure 20. Lamp Driver Figure 21. Current Monitor

Figure 22. Driving TTL Figure 23. Voltage Follower

Copyright © 2017, Texas Instruments Incorporated Submit Documentation Feedback 13

Typical Applications (continued)

Figure 24. Pulse Generator Figure 25. Squarewave Oscillator

IO = 1 amp/volt VIN (Increase RE for Io small)