Professional Documents
Culture Documents
Lmx24-N, Lm2902-N Low-Power, Quad-Operational Amplifiers: 1 Features 3 Description
Lmx24-N, Lm2902-N Low-Power, Quad-Operational Amplifiers: 1 Features 3 Description
LM124-N, LM224-N
LM2902-N, LM324-N
SNOSC16D – MARCH 2000 – REVISED JANUARY 2015
– Power Drain Suitable for Battery Operation (1) For all available packages, see the orderable addendum at
the end of the datasheet.
– In the Linear Mode the Input Common-Mode,
Voltage Range Includes Ground and the Schematic Diagram
Output Voltage
– Can Swing to Ground, Even Though Operated
from Only a Single Power Supply Voltage
– Unity Gain Cross Frequency is Temperature
Compensated
– Input Bias Current is Also Temperature
Compensated
2 Applications
• Transducer Amplifiers
• DC Gain Blocks
• Conventional Op Amp Circuits
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM124-N, LM224-N
LM2902-N, LM324-N
SNOSC16D – MARCH 2000 – REVISED JANUARY 2015 www.ti.com
Table of Contents
1 Features .................................................................. 1 7.3 Feature Description................................................. 11
2 Applications ........................................................... 1 7.4 Device Functional Modes........................................ 11
3 Description ............................................................. 1 8 Application and Implementation ........................ 13
4 Revision History..................................................... 2 8.1 Application Information............................................ 13
8.2 Typical Applications ............................................... 13
5 Pin Configuration and Functions ......................... 3
6 Specifications......................................................... 4 9 Power Supply Recommendations...................... 23
6.1 Absolute Maximum Ratings ...................................... 4 10 Layout................................................................... 23
6.2 ESD Ratings.............................................................. 4 10.1 Layout Guidelines ................................................. 23
6.3 Recommended Operating Conditions....................... 4 10.2 Layout Example .................................................... 23
6.4 Thermal Information .................................................. 5 11 Device and Documentation Support ................. 24
6.5 Electrical Characteristics: LM124A/224A/324A ........ 5 11.1 Related Links ........................................................ 24
6.6 Electrical Characteristics: LM124-N/224-N/324- 11.2 Trademarks ........................................................... 24
N/2902-N ................................................................... 6 11.3 Electrostatic Discharge Caution ............................ 24
6.7 Typical Characteristics .............................................. 8 11.4 Glossary ................................................................ 24
7 Detailed Description ............................................ 11 12 Mechanical, Packaging, and Orderable
7.1 Overview ................................................................. 11 Information ........................................................... 24
7.2 Functional Block Diagram ....................................... 11
4 Revision History
Changes from Revision C (November 2012) to Revision D Page
• Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section ............................... 1
J Package
14-Pin CDIP
Top View
D Package
14-Pin SOIC
Top View
Pin Functions
PIN
TYPE DESCRIPTION
NAME NO.
OUTPUT1 1 O Output, Channel 1
INPUT1- 2 I Inverting Input, Channel 1
INPUT1+ 3 I Noninverting Input, Channel 1
V+ 4 P Positive Supply Voltage
INPUT2+ 5 I Nonnverting Input, Channel 2
INPUT2- 6 I Inverting Input, Channel 2
OUTPUT2 7 O Output, Channel 2
OUTPUT3 8 O Output, Channel 3
INPUT3- 9 I Inverting Input, Channel 3
INPUT3+ 10 I Noninverting Input, Channel 3
GND 11 P Ground or Negative Supply Voltage
INPUT4+ 12 I Noninverting Input, Channel 4
INPUT4- 13 I Inverting Input, Channel 4
OUTPUT4 14 O Output, Channel 4
6 Specifications
6.1 Absolute Maximum Ratings
(1) (2)
See .
LM124-N/LM224-N/LM324-N
LM2902-N
LM124A/LM224A/LM324A
MIN MAX MIN MAX UNIT
Supply Voltage, V+ 32 26 V
Differential Input Voltage 32 26 V
Input Voltage −0.3 32 −0.3 26 V
Input Current (VIN < −0.3 V) (3) 50 50 mA
Power PDIP 1130 1130 mW
Dissipation (4)
CDIP 1260 1260 mW
SOIC Package 800 800 mW
Output Short-Circuit to GND +
V ≤ 15 V and TA = 25°C Continuous Continuous
(One Amplifier) (5)
Lead Temperature (Soldering, 10 seconds) 260 260 °C
Dual-In-Line Soldering (10 seconds) 260 260 °C
Soldering Package
Information Small Vapor Phase (60 seconds) 215 215 °C
Outline
Infrared (15 seconds) 220 220 °C
Package
Storage temperature, Tstg –65 150 –65 150 °C
(1) Refer to RETS124AX for LM124A military specifications and refer to RETS124X for LM124-N military specifications.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of
the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is
also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the op amps to go to
the V+voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and
normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than −0.3 V (at 25°C).
(4) For operating at high temperatures, the LM324-N/LM324A/LM2902-N must be derated based on a 125°C maximum junction
temperature and a thermal resistance of 88°C/W which applies for the device soldered in a printed circuit board, operating in a still air
ambient. The LM224-N/LM224A and LM124-N/LM124A can be derated based on a 150°C maximum junction temperature. The
dissipation is the total of all four amplifiers—use external resistors, where possible, to allow the amplifier to saturate of to reduce the
power which is dissipated in the integrated circuit.
(5) Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of 15 V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
(1) These specifications are limited to −55°C ≤ TA ≤ +125°C for the LM124-N/LM124A. With the LM224-N/LM224A, all temperature
specifications are limited to −25°C ≤ TA ≤ +85°C, the LM324-N/LM324A temperature specifications are limited to 0°C ≤ TA ≤ +70°C, and
the LM2902-N specifications are limited to −40°C ≤ TA ≤ +85°C.
(2) VO ≃ 1.4V, RS = 0 Ω with V+ from 5 V to 30 V; and over the full input common-mode range (0 V to V+ − 1.5 V) for LM2902-N, V+ from 5
V to 26 V.
(3) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
(4) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3 V (at 25°C). The
upper end of the common-mode voltage range is V+ − 1.5 V (at 25°C), but either or both inputs can go to 32 V without damage (26 V for
LM2902-N), independent of the magnitude of V+.
(5) Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This
typically can be detected as this type of capacitance increases at higher frequencies.
(6) Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of 15 V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.
Copyright © 2000–2015, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N
LM124-N, LM224-N
LM2902-N, LM324-N
SNOSC16D – MARCH 2000 – REVISED JANUARY 2015 www.ti.com
VIN+ = +1V,
Source VIN− = 0V, 10 20 10 20 10 20
Output V+ = 15V
VO = 2 V mA
Current VIN− = +1V, 10 15 5 8 5 8
Sink VIN+ = 0V,
V+ = 15V
(1) These specifications are limited to −55°C ≤ TA ≤ +125°C for the LM124-N/LM124A. With the LM224-N/LM224A, all temperature
specifications are limited to −25°C ≤ TA ≤ +85°C, the LM324-N/LM324A temperature specifications are limited to 0°C ≤ TA ≤ +70°C, and
the LM2902-N specifications are limited to −40°C ≤ TA ≤ +85°C.
(2) VO ≃ 1.4V, RS = 0 Ω with V+ from 5 V to 30 V; and over the full input common-mode range (0 V to V+ − 1.5 V) for LM2902-N, V+ from 5
V to 26 V.
(3) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
(4) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3 V (at 25°C). The
upper end of the common-mode voltage range is V+ − 1.5 V (at 25°C), but either or both inputs can go to 32 V without damage (26 V for
LM2902-N), independent of the magnitude of V+.
(5) Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This
typically can be detected as this type of capacitance increases at higher frequencies.
6 Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated
V+ = 30 V (LM2902-N, RL = 2 kΩ 26 26 22
Output VOH V
Voltage V+ = 26 V) RL = 10 kΩ 27 28 27 28 23 24
Swing
VOL V+ = 5 V, RL = 10 kΩ 5 20 5 20 5 100 mV
VIN+
= 1 V,
Source VO = 2 V VIN−
= 0 V, 10 20 10 20 10 20 mA
+
Output V = 15 V
Current VIN− = 1 V,
Sink VIN+ = 0 V, 5 8 5 8 5 8 mA
V+ = 15 V
(6) Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of 15 V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.
Figure 7. Voltage Follower Pulse Response Figure 8. Voltage Follower Pulse Response (Small Signal)
Figure 9. Large Signal Frequency Response Figure 10. Output Characteristics Current Sourcing
Figure 11. Output Characteristics Current Sinking Figure 12. Current Limiting
Figure 13. Input Current (LM2902-N Only) Figure 14. Voltage Gain (LM2902-N Only)
7 Detailed Description
7.1 Overview
The LM124-N series are op amps which operate with only a single power supply voltage, have true-differential
inputs, and remain in the linear mode with an input common-mode voltage of 0 VDC. These amplifiers operate
over a wide range of power supply voltage with little change in performance characteristics. At 25°C amplifier
operation is possible down to a minimum supply voltage of 2.3 VDC.
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
Figure 19. LED Driver Figure 20. “BI-QUAD” RC Active Bandpass Filter
Figure 28. Pulse Generator Figure 29. High Compliance Current Sink
Figure 30. Low Drift Peak Detector Figure 31. Comparator With Hysteresis
VO = VR
Figure 32. Ground Referencing a Differential Input Figure 33. Voltage Controlled Oscillator Circuit
Signal
Q=1 AV = 2
Figure 34. Photo Voltaic-Cell Amplifier Figure 35. DC Coupled Low-Pass RC Active Filter
Figure 41. Using Symmetrical Amplifiers to Reduce Input Current (General Concept)
fO = 1 kHz Q = 25
10 Layout
GND
GND
GND
VIND
GND
VINC
2 2 2 2
GND VOUTA VOUTD GND
VOUTA 1: VOUTA 14: VOUTD VOUTD
1
VINA 1 1 1 1 1
IN-A IN-A 13: IN-D IN-D IN-D VIND
IN-A 2: IN-A IN-D
2
IN+A 2
IN+A 3: IN+A 12: IN+D IN+D
IN+D
1 2
GND
GND V+
V+ 4: V+ 11: GND GND
NC
VI
2 1
2 IN+B 5: IN+B 10: IN+C IN+C
IN+C VINC
VINC
IN+B
VINB
VOUTD
GND GND
11.2 Trademarks
All trademarks are the property of their respective owners.
11.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
www.ti.com 26-Sep-2017
PACKAGING INFORMATION
Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com 26-Sep-2017
Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com 26-Sep-2017
• Automotive: LM2902-Q1
• Enhanced Product: LM2902-EP
• Space: LM124-SP
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
• Enhanced Product - Supports Defense, Aerospace and Medical Applications
• Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com 24-Aug-2017
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com 24-Aug-2017
Pack Materials-Page 2
PACKAGE OUTLINE
J0014A SCALE 0.900
CDIP - 5.08 mm max height
CERAMIC DUAL IN LINE PACKAGE
1
14
12X .100
[2.54] 14X .014-.026
14X .045-.065 [0.36-0.66]
[1.15-1.65]
.010 [0.25] C A B
.754-.785
[19.15-19.94]
7 8
C SEATING PLANE
.308-.314
[7.83-7.97]
AT GAGE PLANE
4214771/A 05/2017
NOTES:
1. All controlling linear dimensions are in inches. Dimensions in brackets are in millimeters. Any dimension in brackets or parenthesis are for
reference only. Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This package is hermitically sealed with a ceramic lid using glass frit.
4. Index point is provided on cap for terminal identification only and on press ceramic glass frit seal only.
5. Falls within MIL-STD-1835 and GDIP1-T14.
www.ti.com
EXAMPLE BOARD LAYOUT
J0014A CDIP - 5.08 mm max height
CERAMIC DUAL IN LINE PACKAGE
(.300 ) TYP
[7.62] SEE DETAIL B
SEE DETAIL A
1 14
12X (.100 )
[2.54]
SYMM
14X ( .039)
[1]
7 8
SYMM
METAL
4214771/A 05/2017
www.ti.com
MECHANICAL DATA
N0014A
NFF0014A
N14A (Rev G)
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2019, Texas Instruments Incorporated