Petronas Technical Standards: Pts Publications and Standard Specifications

PETRONAS TECHNICAL STANDARDS
DESIGN AND ENGINEERING PRACTICE

(CORE)
INDEX
PTS PUBLICATIONS AND STANDARD

SPECIFICATIONS
PTS 00.00.05.05
APRIL 2003
PREFACE
PETRONAS Technical Standards (PTS) publications reflect the views, at the time of publication,
of PETRONAS OPUs/Divisions.
They are based on the experience acquired during the involvement with the design, construction,
operation and maintenance of processing units and facilities. Where appropriate they are based
on, or reference is made to, national and international standards and codes of practice.
The objective is to set the recommended standard for good technical practice to be applied by
PETRONAS' OPUs in oil and gas production facilities, refineries, gas processing plants, chemical
plants, marketing facilities or any other such facility, and thereby to achieve maximum technical
and economic benefit from standardisation.
The information set forth in these publications is provided to users for their consideration and
decision to implement. This is of particular importance where PTS may not cover every
requirement or diversity of condition at each locality. The system of PTS is expected to be
sufficiently flexible to allow individual operating units to adapt the information set forth in PTS to
their own environment and requirements.
When Contractors or Manufacturers/Suppliers use PTS they shall be solely responsible for the
quality of work and the attainment of the required design and engineering standards. In
particular, for those requirements not specifically covered, the Principal will expect them to follow
those design and engineering practices which will achieve the same level of integrity as reflected
in the PTS. If in doubt, the Contractor or Manufacturer/Supplier shall, without detracting from his
own responsibility, consult the Principal or its technical advisor.
The right to use PTS rests with three categories of users :
1) PETRONAS and its affiliates.

2) Other parties who are authorised to use PTS subject to appropriate contractual
arrangements.
3) Contractors/subcontractors and Manufacturers/Suppliers under a contract with
users referred to under 1) and 2) which requires that tenders for projects,
materials supplied or - generally - work performed on behalf of the said users
comply with the relevant standards.
Subject to any particular terms and conditions as may be set forth in specific agreements with
users, PETRONAS disclaims any liability of whatsoever nature for any damage (including injury
or death) suffered by any company or person whomsoever as a result of or in connection with the
use, application or implementation of any PTS, combination of PTS or any part thereof. The
benefit of this disclaimer shall inure in all respects to PETRONAS and/or any company affiliated
to PETRONAS that may issue PTS or require the use of PTS.
Without prejudice to any specific terms in respect of confidentiality under relevant contractual
arrangements, PTS shall not, without the prior written consent of PETRONAS, be disclosed by
users to any company or person whomsoever and the PTS shall be used exclusively for the
purpose they have been provided to the user. They shall be returned after use, including any
copies which shall only be made by users with the express prior written consent of PETRONAS.
The copyright of PTS vests in PETRONAS. Users shall arrange for PTS to be held in safe
custody and PETRONAS may at any time require information satisfactory to PETRONAS in order
to ascertain how users implement this requirement.
PTS 00.00.05.05
April 2003
Page 3
TABLE OF CONTENTS
1. INTRODUCTION ................................................................................................... 4
1.1 SCOPE ................................................................................................................. 4
1.2 TYPES OF PTS .................................................................................................... 4
1.3 STANDARD SPECIFICATIONS ............................................................................ 4
1.4 REQUISITIONS AND STANDARD FORMS............................................................ 4
1.5 DISTRIBUTION OF PTSs ...................................................................................... 5
1.6 AMENDMENTS ..................................................................................................... 5
1.7 CUSTODIANSHIP ................................................................................................. 6
PART I SUBJECT INDEX .................................................................................................. 7
1. GENERAL ENGINEERING SUBJECTS ................................................................ 7
1.1 INDICES ............................................................................................................... 7
1.2 GENERAL.............................................................................................................. 7
2. MECHANICAL ENGINEERING ............................................................................. 8
2.1 GENERAL ............................................................................................................. 8
2.2 EQUIPMENT ......................................................................................................... 8
2.3 CONSTRUCTION MATERIALS............................................................................ 11
2.4 WELDING, GENERAL ......................................................................................... 11
2.5 MAINTENANCE AND INSPECTION .................................................................... 11
2.6 OFFSHORE APPLICATIONS .............................................................................. 12
3. INSTRUMENT ENGINEERING AND TELECOMMUNICATIONS ........................ 13
4. ELECTRICAL ENGINEERING ............................................................................ 14
5. CIVIL ENGINEERING (including steel structures) ............................................ 15
6. SURFACE PROTECTION (coatings, linings and cathodic protection) ............ 16
7. SAFETY AND FIRE FIGHTING ........................................................................... 16
8. DRILLING AND PRODUCTION .......................................................................... 17
PART II NUMERICAL INDICES ....................................................................................... 18
1. PTSS .................................................................................................................. 18
2. STANDARD SPECIFICATIONS .......................................................................... 36
PTS 00.00.05.05
April 2003
Page 4
1. INTRODUCTION
1.1 SCOPE
This index lists the PTSs (PETRONAS Technical Standards) in circulation on the date of
issue of this index. They are listed both by subject type and numerically. In the numerical
indices (Part II, sections 1 and 2), withdrawn PTSs and Standard Specifications have been
included and a reference is shown in parentheses if the withdrawn PTS or Standard
Specification was included in, or replaced by, another publication.
This index replaces the previous index dated September 2002 and changes have been
highlighted by a vertical line (|) in the left margin of the numerical index (Part II, section 1).
1.2 TYPES OF PTS

MANUAL Designated "M"
Manuals aim to give guidance for the way a particular aspect is to be approached, and the
resultant practice or method is outlined.
TECHNICAL SPECIFICATION Designated "T"
Technical specifications aim mainly at a basis for understanding between the Principal,
Contractor and Supplier providing detailed requirements to be satisfied by a product, a
material or a process and indicating the criteria to judge compliance.
PROCEDURAL SPECIFICATION Designated "P"
Procedural specifications aim at describing formalised ways of doing things to achieve a
sound result.
NOTE: The above designations are shown for each active PTS in the 4th column of the numerical section of
this index (Part II).
REQUISITION
Requisitions provide the engineering information required for the procurement of equipment
and materials.
STANDARD FORM
Standard forms are documents used to present information in a consistent manner.
1.3 STANDARD SPECIFICATIONS

Standard Specifications have now all been withdrawn and, where relevant, replaced by
PTSs.
1.4 REQUISITIONS AND STANDARD FORMS

Requisition sheets are indexed in PTS 30.10.01.10
Standard Forms are indexed in PTS 00.00.10.05
PTS 00.00.05.05
April 2003
Page 5
1.5 DISTRIBUTION OF PTSs

The primary, but not exclusive, users of active PTSs are shown in the 5th column of the
numerical indices. The coding is as follows:
'G' for Central Offices and Group companies
'C' for Central Offices, Group companies and their nominated contractors
'F' for Central Offices, Group companies, their nominated contractors and nominated
Manufacturers.
NOTES: 1. The above codings were used in the previous PTS distribution system to determine automatic
distribution of a PTS. They were not, and are not, meant to restrict distribution when a PTS is
requested to be provided. For example, a Manufacturer may be issued with a 'C' coded PTS on
request.
2. This coding system will be discontinued after April 2003.
On a regular basis (currently twice per year) a nominated focal point in each authorised
Group company is sent the specified quantity of new PTS CDROMs.
The Group company is responsible for copying or printing any paper copies that may be
needed.
The Group company is responsible for providing PTSs to their Contractors and
Manufacturers but PETRONAS can provide PTSs directly to Contractors and
Manufacturers for an administrative fee.
1.6 AMENDMENTS
Between formal revisions, if an amendment is required to a PTS, a "PTS Circular" is issued.
These circulars are numbered x/y, where "x" is a sequential number and "y" is the year in
which it was issued.
The 6th column of the numerical section (Part II, section 1) of this index identifies whether a
PTS has been so amended.
PTS 00.00.05.05
April 2003
Page 6
1.7 CUSTODIANSHIP
The Shell GSI and SIEP Custodians responsible for active PTSs are identified in the 7th
column of the numerical index (Part II, section 1).
The current incumbents are as follows:
Custodian Name Location Phone E-mail
EPGO-F Vanderaar, L Rijswijk # 31 70 447 4030 leo.vanderaar@shell.com
EPGO-P Helmer, T Rijswijk # 31 70 447 6367 T.Helmer@shell.com
EPTO-W Brouwer, S Rijswijk # 31 70 447 2062 sjoerd.brouwer@shell.com
EPT-IO Akkermans, F Rijswijk # 31 70 447 3860 frans.akkermans@shell.com
EPT-PB Reece, A.M Houston # 1 713 245 7437 allan.reece@shell.com
EPT-PR Oude Hengel, J Rijswijk # 31 70 311 6049 j.oudehengel@shell.com
OGCC Aarten, T. The Hague #31 70 377 6032 thijs.aarten@shell.com
OGCH/1 Pescott, R.D. The Hague #31 70 377 1484 dick.pescott@shell.com
OGCH/2 Heard, N Chester # 44 151 373 5040 nigel.heard@shell.com
OGEC Krijn, P The Hague # 31 70 377 1828 pieter.krijn@shell.com
OGEE Griffin, P.T. The Hague # 31 70 377 3149 terry.griffin@shell.com
OGEH Bosch, S. Amsterdam # 31 20 630 3140 sjoerd.bosch@shell.com
OGEI/1 Lewis, K. Amsterdam #31 20 630 3147 keith.k.r.lewis@shell.com
OGEI/2 Kerkveld, G. Amsterdam # 31 20 630 2438 gert.kerkveld@shell.com
OGEI/4 Hummel, R. Houston #1 281 544 7616 rjhummel@shell.com
OGEM Mes, H. The Hague # 31 70 377 3977 hans.mes@shell.com
OGER van den Handel, R.J.A.N. The Hague # 31 70 377 2581 ron.vandenhandel@shell.com
OGGL Pek, B. The Hague # 31 70 377 1951 barend.pek@shell.com
OGLA van Geel, C.A.G. The Hague # 31 70 377 2026 cees.vangeel@shell.com
OGPS Bakker, H The Hague # 31 70 377 2136 hans.h.l.m.bakker@shell.com
OGRD van Wijk, R. Amsterdam # 31 20 630 2044 ron.vanwijk@shell.com
OGLM Jagannathan, A. The Hague # 31 70 377 6268 jag.j.jagannathan@shell.com
OGRC Muller, F Amsterdam # 31 20 630 2375 fred.muller@shell.com
OGRT Schrijvers, F.A.M. Amsterdam # 31 20 630 2734 frans.schrijvers@shell.com
OGRU Vasmel, H. Amsterdam # 31 20 630 2472 henk.vasmel@shell.com
OGUA Leitko, A Houston # 1 281 544 7937 alan.leitko@shell.com
OGUD Mossman, J. Rijswijk # 31 70 311 3553 john.mossman@shell.com
OGUF Colenbrander, G.W. Amsterdam # 31 20 630 3384 gert.colenbrander@shell.com
OGUM Jakeman, S. Rijswijk # 31 70 311 3514 simon.jakeman@shell.com

PTS 00.00.05.05
April 2003
Page 7
PART I SUBJECT INDEX
1. GENERAL ENGINEERING SUBJECTS
1.1 INDICES
Title PTS Number

Index to PTSs PTS 00.00.05.05
Index to standard drawings PTS 00.00.06.06
1.2 GENERAL
PTS publications (procedural specification) PTS 00.00.00.30
Content and drafting of a functional specification, and a technical specification, and the PTS 00.00.07.30
classification of products, processes and services (endorsement of ISO 13879, ISO 13880
and ISO/TR 13881)
Standard forms PTS 00.00.10.05
The use of SI quantities and units (endorsement of ISO 31 and ISO 1000) PTS 00.00.20.10
Definition of temperature, pressure and toxicity levels PTS 01.00.01.30
Preparation of process flow schemes and process engineering flow schemes PTS 01.00.02.11
Preparation of safeguarding memoranda and process safeguarding flow schemes PTS 01.00.02.12
Asset breakdown for onshore facilities PTS 01.00.09.10
Preparation and microfilming of technical drawings PTS 02.00.00.10
Steam injection systems for safeguarding thermal cracking units PTS 10.02.51.11
Basic data and phase behaviour methods PTS 20.00.10.10
Glycol-type gas dehydration and hydrate inhibition systems PTS 20.04.10.10
Requisitioning PTS 30.10.01.10
Plant model construction and review PTS 30.10.05.11
Capital project coding system PTS 40.10.01.11
Spare parts PTS 70.10.90.11
Area classification (amendments/supplements to IP 15) PTS 80.00.10.10
Project quality assurance PTS 82.00.10.10
Cost control of capital investment projects PTS 82.00.10.11
PTS 00.00.05.05
April 2003
Page 8
2. MECHANICAL ENGINEERING
2.1 GENERAL
Title PTS Number
Heat transfer fluid (HTF) systems PTS 20.05.50.10

Fuel systems PTS 20.05.60.10
Equipment in LPG installations PTS 30.06.10.11
Pressurised bulk storage installations for LPG PTS 30.06.10.12
LPG - bulk transfer and transportation PTS 30.06.10.13
ESD systems for loading and discharging refrigerated and pressurised LNG and LPG PTS 30.06.10.20
carriers
Glass lined steel equipment and piping PTS 30.48.70.30
Chemical injection facilities PTS 31.01.10.10
Loading facilities for bulk road vehicles PTS 31.06.11.11
Symbols and identification system – Mechanical PTS 31.10.03.10
Gaseous oxygen systems PTS 31.10.11.31

Instrument air supply PTS 31.37.00.11
Diesel oil systems in oil and gas production facilities PTS 37.05.10.11
2.2 EQUIPMENT
2.2.1 General/noise/safety relief systems

Noise control PTS 31.10.00.31
Fabric expansion joints - Selection and application PTS 31.24.40.12
Filters for removing particles from hydroprocesser feeds - type selection and design rules PTS 31.27.21.10
Dry electrostatic precipitators PTS 31.27.21.30
Steam jet vacuum ejector sets PTS 31.29.56.31
Hydraulic systems for remote operation of shut-off valves PTS 31.36.10.30
PTFE bellows PTS 31.38.82.31
Acoustic insulation for piping PTS 31.46.00.31
Relief valves - selection, sizing and specification PTS 80.36.00.30
Pressure relief, emergency depressuring, flare and vent systems PTS 80.45.10.10
Interlocking systems for safety/relief valves PTS 80.46.30.11
2.2.2 Boilers/furnaces
Title PTS Number
Water-tube boiler installations PTS 30.75.10.30
Gas turbine heat recovery steam generators PTS 30.75.10.31

Fired heaters, including waste heat boilers (amendments/supplements to API 560) PTS 31.24.00.30
2.2.3 Heat exchangers

Fouling resistances for heat transfer equipment PTS 20.21.00.31
Shell-and-tube heat exchangers (amendments/supplements to TEMA Standards) PTS 31.21.01.30
Selected construction materials for shell-and-tube heat exchangers PTS 31.21.01.31
Plate and frame heat exchangers (amendments/supplements to ISO 15547) PTS 31.21.01.32
Air-cooled heat exchangers (amendments/supplements to ISO 13706) PTS 31.21.70.31
PTS 00.00.05.05
April 2003
Page 9
2.2.4 Vessels/columns/reactors
Internals for columns PTS 31.20.20.31
Rotating disc contactors PTS 31.22.01.31
Gas/liquid separators - Type selection and design rules PTS 31.22.05.11
Liquid/liquid and gas/liquid/liquid (three-phase) separators - Type selection and design rules PTS 31.22.05.12
Pressure vessels (amendments/supplements to PD 5500) PTS 31.22.10.32
Manufacturing report for pressure vessels PTS 31.22.10.35
Pressure vessels (amendments/supplements to ASME VIII, Division 1 and Division 2) PTS 31.22.20.31
Glass-fibre reinforced epoxy and polyester vessels - design and installation PTS 31.22.30.14
Materials and fabrication requirements for Cr-Mo heavy wall pressure vessels PTS 30.10.02.32
(amendments/supplements to API RP 934)
2.2.5 Rotating equipment

Title PTS Number
Hoisting facilities and weather protection for rotating equipment PTS 31.25.00.10
Installation of rotating equipment PTS 31.29.00.10
Oil mist lubrication systems PTS 31.29.00.30
Special purpose gear units for petroleum, chemical and gas industry services PTS 31.29.00.32
(amendments/supplements to API STD 613)
Shaft sealing systems for centrifugal and rotary pumps (amendments/supplements to API PTS 31.29.00.33
682)
Dry gas seal systems for centrifugal compressors PTS 31.29.00.34
Flexible couplings for mechanical power transmission - special purpose applications PTS 31.29.00.36
(amendments/ supplements to ISO 10441 and ISO 14691)
Pumps - type selection PTS 31.29.02.11
Centrifugal pumps (amendments/supplements to API Std 610) PTS 31.29.02.30
Centrifugal submerged motor pumps (in refrigerated product or pressurised storage service) PTS 31.29.06.30
Reciprocating positive displacement pumps and metering pumps PTS 31.29.12.30
(amendments/supplements to API 674 and API 675)
Compressors - Selection, testing and installation PTS 31.29.40.10
Centrifugal and axial compressors (amendments/supplements to API Std 617) PTS 31.29.40.30
Reciprocating compressors (amendments/supplements to API 618) PTS 31.29.40.31
Rotary-type positive displacement compressors (amendments/supplements to API 619) PTS 31.29.40.32
Packaged, integrally geared, centrifugal plant and instrument air compressors PTS 31.29.40.33
(amendments/supplements to API Std 672)
Liquid ring vacuum pumps and compressors (amendments/supplements to API 681) PTS 31.29.42.30
Centrifugal fans (amendments/supplements to API 560, Appendix E) PTS 31.29.47.30
Steam turbines - Selection, testing and installation PTS 31.29.60.10
General-purpose steam turbines (amendments/supplements to API Std 611) PTS 31.29.60.30
Special-purpose steam turbines (amendments/supplements to API Std 612) PTS 31.29.60.31
Lubrication, shaft-sealing and control oil systems and auxiliaries for petroleum, chemical and PTS 31.29.60.32
gas industry services (amendments/supplements to API 614)
Combustion gas turbines - Selection, testing and installation PTS 31.29.70.11
Combustion gas turbines (amendments/supplements to API 616) PTS 31.29.70.31
Gas turbine combustion air intake and exhaust systems PTS 31.29.70.32
Diesel engines PTS 31.29.80.30
Spark ignited gas fuelled engines PTS 31.29.90.30
PTS 00.00.05.05
April 2003
Page 10
2.2.6 Piping and pipelines

Title PTS Number
Side-entry mixers for storage tanks & vessels PTS 31.51.10.31

Fabrication of heater piping PTS 31.24.49.31
Pipeline transportation systems - pipeline valves (amendments/supplements to ISO 14313) PTS 31.36.00.30
Piping classes - basis of design PTS 31.38.01.10

Piping - general requirements PTS 31.38.01.11
Piping classes - refining and chemicals PTS 31.38.01.12
Compilation of bill of material for piping isometrics PTS 31.38.01.13
Piping classes - exploration and production PTS 31.38.01.15
Compilation of a specification for piping systems PTS 31.38.01.21
Pipe supports PTS 31.38.01.29
Shop and field fabrication of steel piping PTS 31.38.01.31
Protective steam heating of piping systems PTS 31.38.30.11
Hot-tapping on pipelines, piping and equipment PTS 31.38.60.10
Pipeline engineering PTS 31.40.00.10
Corrosion mitigation strategy for wet sour gas carbon steel pipelines PTS 31.40.00.19
Riser design PTS 31.40.10.10
Design of multiple-pipe slug catchers PTS 31.40.10.12
Design of pipeline pig trap systems PTS 31.40.10.13
Pipeline overpressure protection PTS 31.40.10.14
Analysis of spans for submerged pipelines PTS 31.40.10.15
Upheaval buckling of pipelines PTS 31.40.10.16
Pipeline/trawlgear interaction PTS 31.40.10.17
GRP Pipelines and piping systems (amendments/supplements to UKOOA documents) PTS 31.40.10.19
CRA clad or lined steel pipe (amendments/supplements to API Spec 5LD) PTS 31.40.20.32
Linepipe induction bends PTS 31.40.20.33
(amendments/supplements to ISO 15590-1)
Welded and seamless duplex and super duplex stainless steel line pipe PTS 31.40.20.34
(amendments/supplements to API Spec 5LC)
Linepipe for non-critical service (amendments/supplements to ISO 3183-1) PTS 31.40.20.35
Weldable martensitic stainless steel line pipe for use in oil and gas operations PTS 31.40.20.36
(amendments/supplements to API Spec 5LC)
Linepipe for critical service (amendments/supplements to ISO 3183-3) PTS 31.40.20.37
Pipeline fittings (amendments/supplements to MSS SP-75) PTS 31.40.21.30
Pipeline isolating joints (amendments/supplements to MSS SP-75) PTS 31.40.21.31
Pig signallers: Intrusive type PTS 31.40.21.33
Carbon and low alloy steel pipeline flanges for use in oil and gas operations PTS 31.40.21.34
(amendments/supplements to MSS SP-44)
Thermoplastic lined pipelines PTS 31.40.30.34
Hydrostatic pressure testing of new pipelines PTS 31.40.40.38
Precommissioning of pipelines PTS 31.40.50.30
Pipeline leak detection PTS 31.40.60.11
PTS 00.00.05.05
April 2003
Page 11
Pipeline Repairs (supplements to ANSI/ASME B31.4 and B31.8) PTS 31.40.60.12

Quarter-turn on/off actuators PTS 31.40.70.30
L80 13%Cr casing and tubing (amendments/supplements to ISO/DIS 11960.2) PTS 39.01.20.10
Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock - PTS 39.01.20.30
technical delivery conditions (endorsement of ISO 13680)
Care and use of casing and tubing (endorsement of ISO 10405) PTS 39.01.20.31
Shop and field fabrication of orifice meter runs PTS 61.38.10.10
Welding of pipelines and related facilities (amendments/supplements to ANSI/API STD 1104) PTS 61.40.20.30
Field welding of duplex and super duplex stainless steel pipelines PTS 61.40.20.31
(amendments/supplements to API 1104)
2.3 CONSTRUCTION MATERIALS

Title PTS Number
Metallic materials - selected standards PTS 30.10.02.11
Non-metallic materials - selection and application PTS 30.10.02.13
Metallic materials - prevention of brittle fracture PTS 30.10.02.31
Materials for high-temperature conversion process furnace parts PTS 31.24.40.31
2.4 WELDING, GENERAL

Welding of metals PTS 30.10.60.18
Welding on pressurised pipes (amendments/supplements to ANSI/API RP1107) PTS 30.10.60.30
Oxidation of stainless steel weldments PTS 30.10.60.31
2.5 MAINTENANCE AND INSPECTION

Field inspection prior to commissioning of mechanical equipment PTS 61.10.08.11
Equipment and tools for maintenance PTS 70.08.10.11
Mechanical maintenance equipment, tools and bolt tensioning
Equipment and tools for maintenance and inspection
- Part 4 - Electrical workshop - Test equipment and tools PTS 70.08.10.13
Equipment record cards PTS 70.10.01.10
The preservation of old and new equipment and piping standing idle PTS 70.10.70.11
Cleaning of equipment PTS 70.10.80.11
PTS 00.00.05.05
April 2003
Page 12
2.6 OFFSHORE APPLICATIONS

Telecommunications for offshore platforms PTS 32.71.00.12
Design of sea water systems and utility heat transfer systems for offshore installations PTS 37.05.10.10
Design of hose bulk transfer facilities for offshore installations PTS 37.05.10.12
Site specific assessment of mobile offshore jack-up units PTS 37.11.00.30
(amendments/supplements to the SNAME guideline and recommended practice)
Drain systems for offshore installations PTS 37.14.10.10
Design of offshore living quarters PTS 37.17.10.10
Design of offshore temporary refuges PTS 37.17.10.11
Design of steel substructures for fixed offshore platforms PTS 37.19.00.30
(amendments/supplements to API RP 2A-LRFD)
Weldable structural steels for fixed offshore structures PTS 37.19.10.30
(amendments/supplements to BS 7191)
Structural inspection of offshore installations PTS 37.19.60.10
Firewater pumps for offshore installations PTS 37.29.01.10
Subsea production systems (endorsement of ISO 13628 and API 17 series) PTS 37.80.00.30
Mooring of mobile units PTS 37.91.10.11
Oil loading and discharge hoses for offshore mooring installations PTS 37.91.20.30
(amendments/supplements to OCIMF Guide)
Pedestal cranes (amendments/supplements to API Spec 2C) PTS 37.92.10.30
Pedestal cranes (amendments/supplements Lloyd's code and BS 2573) PTS 37.92.10.31
Offshore facilities life-saving appliance requirements (amendments/supplements to SOLAS) PTS 80.80.00.10
PTS 00.00.05.05
April 2003
Page 13
3. INSTRUMENT ENGINEERING AND TELECOMMUNICATIONS
Title PTS Number
Human-machine interface in a control room PTS 32.00.00.11
Instrumentation symbols and identification on process engineering flow schemes PTS 32.10.03.10
Control system and instrumented protective functions for fired equipment PTS 32.24.20.30
- System for a single-burner furnace (S24.024 and S 24.026)
Control system and instrument protective functions for fired equipment PTS 32.24.20.33
System for an automatically started, gas fired, natural draught, multi-burner furnace,
safeguarded by pilot burners (S 24.033)
- System for a manually-started, forced draught, multi-burner furnace or boiler (S 24.021)
- System for an automatically-started, forced draught, multi-burner furnace or boiler (S24.030
or S 24.034)
- System for a tangentially gas-fired CO boiler (S 24.036)
- Systems for co-fired gas turbine waste heat recovery units
Fire, gas and smoke detection systems PTS 32.30.20.11
Instrument engineering procedures PTS 32.31.00.10
Instruments for measurement and control PTS 32.31.00.32
Instrumentation documents and drawings PTS 32.31.00.34
Instrumentation for equipment packages PTS 32.31.09.31
On-line process stream analysis
- Sample take-off and transportation PTS 32.31.50.10
- Sample conditioning PTS 32.31.50.11
- Analysers PTS 32.31.50.12
- Analyser houses PTS 32.31.50.13
Turbine fiscal metering systems for liquid hydrocarbon PTS 32.32.00.11
Fiscal flow measurement of natural gas PTS 32.32.00.12
Control valves: Selection sizing and specification PTS 32.36.01.17
Installation of on-line instruments PTS 32.37.10.11
Instrument signal lines PTS 32.37.20.10
System cabling PTS 32.37.20.31
Instrument air lines PTS 32.37.51.11
Instrumentation of depressuring systems PTS 32.45.10.10
Plant telecommunication PTS 32.71.00.10
Telecommunication standards PTS 32.71.00.11
Drilling communications PTS 32.71.00.13
Telecommunications towers and guyed masts PTS 32.71.00.14
Design and installation of telephone cabling PTS 32.71.00.16
Structured cabling systems for telecommunications PTS 32.71.00.30
Microwave systems PTS 32.71.00.31
Classification and implementation of instrumented protective functions PTS 32.80.10.10
Management of instrumented protective functions PTS 32.80.10.12
Instrumented protective systems PTS 32.80.10.30
Inspection and functional testing of instruments PTS 62.10.08.11
PTS 00.00.05.05
April 2003
Page 14
4. ELECTRICAL ENGINEERING
Title PTS Number

Electrical engineering guidelines PTS 33.64.10.10
Electrical network monitoring and control system - application PTS 33.64.10.11
Electrical supply and generation - design and operation PTS 33.64.10.12
Electrical network monitoring and control system - specification PTS 33.64.10.32
Electromagnetic compatibility (EMC) requirements PTS 33.64.10.33
Synchronous AC machines (Amendments/supplements to IEC 60034-1) PTS 33.65.11.31
Packaged unit AC generator sets PTS 33.65.11.32
Power transformers (amendments/supplements to IEC 76 and IEC 726) PTS 33.65.40.31
Static DC uninterruptible power supply (DC UPS) units PTS 33.65.50.31
Static AC uninterruptible power supply unit (Static AC UPS unit) PTS 33.65.50.32
Electric machines - Cage-induction types (Amendments/supplements to IEC 60034-1) PTS 33.66.05.31
Electrical variable speed drive systems PTS 33.66.05.33
Low-voltage switchgear and controlgear assemblies (amendments/supplements to PTS 33.67.01.31
IEC 439-1)
High-voltage switchgear and controlgear assemblies (amendments/supplements to IEC 298) PTS 33.67.51.31
Electrical heating system for frost heave prevention of refrigerated hydrocarbon storage PTS 33.68.30.31
tanks
Electrical trace heating PTS 33.68.30.32
Electrical process heaters PTS 33.68.30.33
Navigational aids for offshore structures PTS 33.80.00.30
Field commissioning and maintenance of electrical installations and equipment PTS 63.10.08.11
PTS 00.00.05.05
April 2003
Page 15
5. CIVIL ENGINEERING (including steel structures)
Title PTS Number
Heating, ventilation and air conditioning for plant buildings PTS 31.76.10.10
Installation, testing and balancing, and commissioning of HVAC systems PTS 31.76.10.11
Minimum requirements for structural design and engineering PTS 34.00.01.30
Site investigations PTS 34.11.00.10
Site preparation and earthworks including tank foundations and tank farms PTS 34.11.00.11
Geotechnical and foundation engineering PTS 34.11.00.12
Roads, paving, surfacing, slope protection and fencing PTS 34.13.20.31
Drainage and primary treatment facilities PTS 34.14.20.31
Minimum requirements for design and engineering of buildings PTS 34.17.00.32
Reinforced control buildings/Field auxiliary rooms PTS 34.17.10.30
Laboratories PTS 34.17.10.31
Fireproofing of steel structures PTS 34.19.20.11
Reinforced concrete foundations and structures PTS 34.19.20.31
Steel stacks (amendments/supplements to CICIND Model Code) PTS 34.24.26.31
Reinforced concrete stacks PTS 34.24.27.31
Steel structures PTS 34.28.00.31
Standard vertical tanks - Selection, design and fabrication PTS 34.51.01.31
Mounded horizontal cylindrical bulk storage vessels for pressurised gases at ambient PTS 34.51.11.30
temperatures
Demolition of storage tanks (endorsement of EEMUA 154) PTS 34.51.90.10
Standard vertical tanks - Field erection and testing PTS 64.51.01.31
Field inspection, maintenance and repair of vertical steel storage tanks PTS 70.51.10.11
PTS 00.00.05.05
April 2003
Page 16
6. SURFACE PROTECTION (coatings, linings and cathodic protection)
Title PTS Number
Cathodic protection PTS 30.10.73.10
Design of cathodic protection systems for onshore buried pipelines PTS 30.10.73.31
Design of cathodic protection systems for offshore pipelines PTS 30.10.73.32
(amendments/supplements to DNV RP B401)
Installation and commissioning of cathodic protection systems PTS 30.10.73.33
Thermal insulation (amendments/supplements to the CINI Manual “Insulation for Industries”) PTS 30.46.00.31
Painting and coating of new equipment PTS 30.48.00.31
Cement lining of pipes PTS 30.48.30.31
Thermal spraying of coatings of zinc, aluminium and their alloys (endorsement of ISO 2063) PTS 30.48.40.31
Electroless nickel plating (amendments/supplements to ASTM B 733) PTS 30.48.41.31
Rubber-lined process equipment and piping PTS 30.48.60.10
Design and installation of chemical-resistant linings for concrete structures PTS 30.48.60.12
Design and installation of chemical-resistant brick lining for process equipment PTS 30.48.60.13
Concrete coating of linepipe PTS 31.40.30.30
External polyethylene and polypropylene coating for line pipe PTS 31.40.30.31
External fusion-bonded epoxy powder coating for line pipe PTS 31.40.30.32
Bituminous enamel coating of steel linepipe PTS 31.40.30.33
Internal coating of line pipe for non-corrosive gas transmission service PTS 31.40.30.35
(amendments/supplements to API RP 5L2)
Polychloroprene riser coatings PTS 31.40.30.36
Design of cathodic protection systems for new fixed offshore steel structures PTS 37.19.30.30
(amendments/supplements to DNV RP B401)
Refractory bricks and shapes PTS 44.24.90.31
Refractory materials for sulphur recovery units (claus and scot) PTS 64.24.32.11
Insulating and dense refractory concrete linings PTS 64.24.32.30
Maintenance painting PTS 70.48.10.10
7. SAFETY AND FIRE FIGHTING

Water-based fire protection systems for offshore facilities PTS 80.47.10.12
Assessment of the fire safety of onshore installations PTS 80.47.10.30
Active fire protection systems and equipment for onshore facilities PTS 80.47.10.31
Fire-fighting agents and movable fire fighting equipment for onshore applications PTS 80.47.10.32
Fire-fighting vehicles and fire stations PTS 80.47.10.33
Control and mitigation of fires and explosions on offshore production installations PTS 80.80.00.11
(amendments/supplements to ISO 13702)
Offshore production installations - Requirements and guidelines for emergency response PTS 80.80.00.12
(amendments/supplements to ISO 15544)
Offshore production installations - Guidelines on tools and techniques for identification and PTS 80.80.00.13
assessment of hazardous events (amendments/supplements to ISO 17776)
PTS 00.00.05.05
April 2003
Page 17
8. DRILLING AND PRODUCTION
Drilling fluid material - specifications and tests (endorsement of ISO 13500) PTS 38.80.10.30
Field testing of drilling fluids - water-based fluids (endorsement of ISO 10414-1) PTS 38.80.10.31
Field testing of drilling fluids – Oil based fluids (amendments/supplements to ISO 10414-2) PTS 38.80.10.32
Specifications for cements and materials for well cementing (endorsement of ISO 10426-1) PTS 38.80.20.30
Selection of materials for life-cycle performance (EP) PTS 39.01.10.11
Wellhead and christmas tree equipment (amendments and supplements to ISO 10423) PTS 39.01.30.30
Downhole equipment - Sub-surface safety valves (endorsement of ISO 10432) PTS 39.01.30.31
PTS 00.00.05.05
April 2003
Page 18
PART II NUMERICAL INDICES

1. PTSS
PTS Date of PTS Intended Amended Custodian

Number issue Title Type use by
Circular
No.
| 00.00.00.30 Apr. 2003 PTS publications (procedural P C OGEM

specification)
| 00.00.05.05 Apr. 2003 Index to PTS publications and - C OGEM
standard specifications
| 00.00.06.06 Apr. 2003 Index to standard drawings - C OGEM
00.00.07.07 Withdrawn Standard specification index
00.00.07.30 Dec. 2000 Content and drafting of a functional M F OGEM
specification, and a technical
specification, and the classification of
products, processes and services
(endorsement of ISO 13879, ISO
13880 and ISO/TR 13881)
| 00.00.10.05 Apr. 2003 Standard forms - C OGEM
00.00.20.10 Aug. 2000 The use of SI quantities and units M F OGEM
(endorsement of ISO 31 and ISO
1000)
00.30.10.05 Withdrawn Standard forms – Instrumentation
binder (Standard Drawings 37.001 and
37.002)
01.00.01.30 Mar. 2001 Definition of temperature, pressure and T C OGCH/1
toxicity levels
| 01.00.02.11 Apr. 2003 Preparation of process flow schemes M C OGCH/1
and process engineering flow schemes
01.00.02.12 Oct. 2001 Preparation of safeguarding M C OGCH/1
memoranda and process safeguarding
flow schemes
01.00.04.11 Withdrawn Preparation of simplified flow schemes
01.00.09.10 Dec. 1998 Asset breakdown for onshore facilities M C OGPS
02.00.00.10 Oct. 1995 Preparation and microfilming of M C 15/99, OGEM
technical drawings 64/2001
05.00.11.11 Withdrawn Time schedules and progress reporting
for new construction projects
05.00.11.80 Withdrawn Punch document for critical path
project schedule
05.00.11.81 Withdrawn Project milestones report
05.00.11.82 Withdrawn Bar-line schedule
05.00.11.83 Withdrawn Key-date schedule
05.00.11.84 Withdrawn Progress graphs
05.00.11.85 Withdrawn Man-hours statement
05.00.55.12 Withdrawn Job instructions (G-5-1)
10.02.51.11 Dec. 1994 Steam injection systems for M C OGRT
safeguarding thermal cracking units
| 20.00.10.10 Apr. 2003 Basic data and phase behaviour M C OGUD
methods
PTS 00.00.05.05
April 2003
Page 19

Circular
No.
20.04.10.10 Dec. 1994 Glycol-type gas dehydration and M C 42/96, OGUD

hydrate inhibition systems 16/99,
45/2001
20.05.50.10 Dec. 1998 Heat transfer fluid (HTF) systems M C OGEH
20.05.60.10 Jul. 1996 Fuel systems M C OGUF
20.21.00.31 Dec. 1998 Fouling resistances for heat transfer T C OGEH
equipment
30.06.10.10 Withdrawn Introduction and physical properties
and characteristics of LPG
30.06.10.11 Jul. 1997 Equipment in LPG installations M C OGLM
30.06.10.12 Jul. 1997 Pressurised bulk storage installations M C OGLM
for LPG
30.06.10.13 Jul. 1997 LPG - bulk transfer and transportation M C OGLM
30.06.10.14 Withdrawn LPG - Cylinder filling and storage
plants
30.06.10.15 Withdrawn LPG - Cylinders and skid tanks
- Consumer equipment and
installations
30.06.10.20 Oct. 1992 ESD systems for loading and M C 17/99, OGGL
discharging refrigerated and 03/2002
pressurised LNG and LPG carriers
30.06.11.11 Withdrawn Pressure storage facilities for LPG
(30.06.10.12)
| 30.10.01.10 Apr. 2003 Requisitioning M C OGEM
30.10.02.11 Sep. 2002 Metallic materials - selected standards M C OGEI
| 30.10.02.13 Apr. 2003 Non-metallic materials - selection and M C OGEI
application
30.10.02.31 Oct. 1995 Metallic materials - prevention of brittle T F 42/97 OGEI
fracture
30.10.02.32 Oct. 2001 Materials and fabrication requirements T F OGEI
for Cr-Mo heavy wall pressure vessels
(amendments/supplements to
API RP 934)
30.10.05.11 Jul. 1996 Plant model construction and review P C OGEM
30.10.40.11 Withdrawn Jointing material
30.10.60.18 Oct. 1995 Welding of metals M F 06/2002 OGEI
30.10.60.19 Withdrawn Welding tubular goods, pressure
vessels and storage tanks
30.10.60.19 Withdrawn Welding procedure specification
(binder)
30.10.60.21 Withdrawn Testing of filler metals for welding
30.10.60.22 Withdrawn Welding and inspection requirements
for equipment not covered by
recognized standards and/or codes
30.10.60.30 Dec. 1998 Welding on pressurised pipes T F 15/2002 OGEI
ANSI/API RP1107)
PTS 00.00.05.05
April 2003
Page 20

Circular
No.
30.10.60.31 Dec. 1998 Oxidation of stainless steel weldments T F OGEI

30.10.73.10 Jun. 1983 Cathodic protection M G 11/84, OGEI
07/2002
30.10.73.31 Dec. 1992 Design of cathodic protection systems T C OGEI
for onshore buried pipelines
30.10.73.32 Jul. 1996 Design of cathodic protection systems T F OGEI
for offshore pipelines
(amendments/supplements to DNV RP
B401)
30.10.73.33 Jan. 2000 Installation and commissioning of T C OGEI
cathodic protection systems
30.46.00.31 Jul. 1999 Thermal insulation T F 35/2001 OGEC
(amendments/supplements to the CINI
Manual “Insulation for Industries”)
30.46.00.32 Withdrawn Thermal insulation for cold and dual-
temperature services (30.46.00.31)
30.48.00.10 Withdrawn Painting and coating
(30.48.00.31, 70.48.10.10)
30.48.00.31 Dec. 1995 Painting and coating of new equipment T OGEI
| 30.48.30.31 Dec. 1998 Cement lining of pipes T 15/2003 OGEC
30.48.40.31 Oct. 1995 Thermal spraying of coatings of zinc, T OGEI
aluminium and their alloys
(endorsement of ISO 2063)
30.48.41.31 Oct. 1995 Electroless nickel plating T F OGEI
ASTM B 733)
30.48.50.11 Withdrawn Requirements for PTFE lined piping
(31.38.01.11)
30.48.50.12 Withdrawn Plastic-lined steel pipes and fittings
(31.38.01.11)
30.48.50.31 Withdrawn PTFE coating of steel surfaces
30.48.50.32 Withdrawn Requirements for plastic-lined steel

pipes and fittings (30.48.50.12)
30.48.60.10 Dec. 1997 Rubber-lined process equipment and M C 30/98 OGEI
piping
30.48.60.12 Aug. 2000 Design and installation of chemical- M C OGEC
resistant linings for concrete structures
| 30.48.60.13 Apr. 2003 Design and installation of chemical- M C OGEI
resistant brick lining for process
equipment
30.48.60.22 Withdrawn Installation of chemical-resistant linings

for concrete structures (30.48.60.12)
30.48.60.23 Withdrawn Installation of chemical-resistant brick
linings for process equipment
(30.48.60.13)
30.48.60.30 Withdrawn Requirements for rubber linings for
process equipment and piping
(30.48.60.10)
PTS 00.00.05.05
April 2003
Page 21

Circular
No.
30.48.60.33 Withdrawn Chemical-resistant (ceramic) lining

materials (30.48.60.12)
30.48.60.34 Withdrawn Erosion resistant refractory linings
(64.24.32.30)
30.48.70.30 Jul. 1998 Glass lined steel equipment and piping T F 70/99 OGEI
30.75.10.30 Jul. 1999 Water-tube boiler installations T F 02/2000 OGEH
19/2001
30.75.10.31 Dec. 1999 Gas turbine heat recovery steam T F 20/2001, OGEH
generators 47/2001
| 31.01.10.10 Apr. 2003 Chemical injection facilities M C OGEI
31.06.11.11 Jul. 1998 Loading facilities for bulk road vehicles M G OGLM
31.06.11.12 Withdrawn Shell loading and discharging manuals
- Loading facilities for bulk road
vehicles - Part 2 - Design of top
loading facilities
(31.06.11.11)
vehicles - Part 3 - Design of bottom
loading facilities
(31.06.11.11)
vehicles - Part 4 - Ancillary equipment,
services and site requirements
(31.06.11.11)
31.06.12.11 Withdrawn Rail tank waggon loading and
discharging
Part 1, Vol. 1: Selection, design and
construction
discharging
Part 1, Vol. 2: Selection, design and
construction
discharging
Part 2: Layouts, examples and
drawings
31.10.00.31 Dec. 1998 Noise control T C OGEM
31.10.03.10 Dec. 1998 Symbols and identification system – M C OGEM
Mechanical
| 31.10.11.31 Oct. 2001 Gaseous oxygen systems T C 35/2003 OGRU
31.10.21.30 Withdrawn Bolt tensioning (70.08.10.11)
31.20.20.31 Sep. 2002 Internals for columns T F OGRD
31.21.00.19 Withdrawn Guide for the specification of shell-and-
tube heat exchangers (31.21.00.93)
31.21.01.30 Jul. 1996 Shell-and-tube heat exchangers T F 04/97, OGEH
(amendments/supplements to TEMA 03/2000
standards)
31.21.01.31 Nov. 1989 Selected construction materials for T C 22/92, OGEI
shell-and-tube heat exchangers 55/97,
11/2002
PTS 00.00.05.05
April 2003
Page 22

Circular
No.
31.21.01.32 Sep. 2002 Plate and frame heat exchangers T C OGEH

(amendments/supplements to ISO
15547)
31.21.20.31 Withdrawn Shell-and-tube heat exchangers with
hot-dip galvanized tubes
31.21.70.31 Mar. 2001 Air-cooled heat exchangers T F OGEH

13706)
31.22.01.31 Dec. 1995 Rotating disc contactors T F OGEM
31.22.05.11 Sep. 2002 Gas/liquid separators - M C OGRD
Type selection and design rules
31.22.05.12 Dec. 1996 Liquid/liquid and gas/liquid/liquid M C 15/2000 OGRD
(three-phase) separators - Type
selection and design rules
31.22.10.31 Withdrawn Pressure vessels
(amendments/supplements to BS 1515
Part 1)
31.22.10.32 Mar. 2001 Pressure vessels T F OGEM
(amendments/supplements to PD
5500)
31.22.10.33 Withdrawn Tolerances for pressure vessels
(31.22.10.32)
31.22.10.34 Withdrawn Pressure vessels
(amendments/supplements to AS
1210)
31.22.10.35 Dec. 1999 Manufacturing report for pressure T C OGCC
vessels
31.22.10.36 Withdrawn LPG storage vessels for aboveground
storage of C3 and heavier
hydrocarbons
(30.06.10.12, 31.22.10.32)
31.22.20.31 Mar. 2001 Pressure vessels T F OGEM
(amendments/supplements to ASME
Section VIII, Division 1 and Division 2)
31.22.30.14 Sep. 2002 Glass-fibre reinforced epoxy and M F OGEI
polyester vessels - design and
installation
31.22.30.24 WIthdrawn Installation of glass-fibre reinforced
epoxy vessels and equipment
(31.22.30.14)
31.22.30.34 WIthdrawn Glass-fibre reinforced epoxy and
polyester vessels - manufacturing
requirements (31.22.30.14)
31.22.90.30 Withdrawn Seamless steel transportable gas
containers (endorsement of
BS 5045-1)
31.24.00.30 Oct. 1995 Fired heaters, including waste heat T F 33/96 OGEH
boilers (amendments/supplements to
API 560)
31.24.15.31 Withdrawn SIPM-type vertical furnaces, including
waste heat boilers (31.24.00.30)
31.24.40.12 Oct. 2001 Fabric expansion joints M F OGEI
PTS 00.00.05.05
April 2003
Page 23

Circular
No.
31.24.40.31 Dec. 2000 Materials for high-temperature T F OGEI

conversion process furnace parts
31.24.49.31 Dec. 1999 Fabrication of heater piping T F OGEI
31.24.66.11 Withdrawn Mobile ignition unit for furnaces and
steam boilers
31.24.66.12 Withdrawn Mobile ignition unit for LMV line

burners of sulphur recovery units
31.25.00.10 Dec. 1999 Hoisting facilities and weather protection M C OGER

for rotating equipment
31.27.21.10 Mar. 2001 Filters for removing particles from M C OGEM
hydroprocesser feeds - type selection
and design rules
31.27.21.30 Jul. 1998 Dry electrostatic precipitators T C 18/99 OGRC
31.29.00.10 Jul. 1996 Installation of rotating equipment M C 18/2001, OGER
27/2002
31.29.00.30 Dec. 2000 Oil mist lubrication systems T C OGER
31.29.00.31 Withdrawn Noise limitation (31.10.00.31)
31.29.00.32 Dec. 1995 Special purpose gear units for T F 23/97, OGER
petroleum, chemical and gas industry 22/99
services (amendments/supplements to
API STD 613)
31.29.00.33 Jul. 1998 Shaft sealing systems for centrifugal T F OGER
and rotary pumps
31.29.00.34 Jul. 1998 Dry gas seal systems for centrifugal M F OGER
compressors
31.29.00.36 Oct. 2001 Flexible couplings for mechanical T F OGER
power transmission - special purpose
applications (amendments/
supplements to ISO 10441 and ISO
14691)
31.29.02.11 Jul. 1998 Pumps - Type Selection M C 30/2001 OGER
31.29.02.30 Dec. 1998 Centrifugal pumps T F 52/99, OGER
(amendments/supplements to API Std 02/2002
610)
31.29.05.31 Withdrawn Vertical in-line centrifugal pumps
| 31.29.06.30 Apr. 2003 Centrifugal submerged motor pumps T F OGER
(in refrigerated product or pressurised
storage service)
31.29.12.30 Dec. 1999 Reciprocating positive displacement T F 01/2002 OGER
pumps and metering pumps
(amendments/supplements to API 674
and API 675)
31.29.40.10 Jul. 1998 Compressors - Selection, testing and M C OGER
installation
31.29.40.30 Dec. 1998 Centrifugal and axial compressors T F 23/99 OGER
(amendments/supplements to API Std
617)
| 31.29.40.31 Dec. 1999 Reciprocating compressors T F 06/2000, OGER
(amendments/supplements to API Std 48/2001,
618) 16/2003
PTS 00.00.05.05
April 2003
Page 24

Circular
No.
31.29.40.32 Dec. 1999 Rotary-type positive displacement T F OGER

compressors
31.29.40.33 Sep. 2002 Packaged, integrally geared, T F OGER
centrifugal plant and instrument air
compressors
API Std 672)
31.29.42.30 Jul. 1997 Liquid ring vacuum pumps and T F OGEM
compressors
31.29.47.30 Jan. 1998 Centrifugal fans T F 27/99 OGER
(amendments/supplements to API 560
Appendix E)
31.29.56.31 Dec. 1997 Steam jet vacuum ejector sets T F 28/99 OGEM
| 31.29.60.10 Apr. 2003 Steam turbines - Selection, testing and M C OGER
installation
31.29.60.30 Aug. 2000 General-purpose steam turbines T F OGER
API Std 611)
31.29.60.31 Dec. 1998 Special-purpose steam turbines T F 30/99 OGER
API Std 612)
31.29.60.32 Dec. 1999 Lubrication, shaft-sealing and control T F OGER
oil systems and auxiliaries for
petroleum, chemical and gas industry
services (amendments/supplements to
API 614)
31.29.70.11 Dec. 1998 Combustion gas turbines M C OGER
- Selection, testing and installation
31.29.70.31 Dec. 1999 Combustion gas turbines T F OGER
31.29.70.32 Dec. 1999 Gas turbine combustion air intake and T F OGEM
exhaust systems
31.29.80.30 Dec. 2000 Diesel engines T F OGER
31.29.90.30 Mar. 2001 Spark ignited gas fuelled engines T F OGER
31.36.00.30 Oct.2001 Pipeline transportation systems - T F EPT-PR
pipeline valves
14313)
31.36.10.30 Sep. 2002 Hydraulic systems for remote operation T F OGEM
of shut-off valves
31.37.00.11 Jul. 1985 Instrument air supply M C OGRU
31.38.01.10 Jan. 2000 Piping classes - basis of design M C 49/2001 OGEM
| 31.38.01.11 Sep. 2002 Piping - general requirements M C 27/2003 OGEM
| 31.38.01.12 Apr. 2003 Piping classes - refining and chemicals M C OGEM
31.38.01.13 Dec. 1998 Compilation of bill of material for piping M C 26/2002 OGEM
isometrics
PTS 00.00.05.05
April 2003
Page 25

Circular
No.
31.38.01.15 Dec. 1999 Piping classes - exploration and M C OGEM

production
31.38.01.21 Dec. 1998 Compilation of a specification for piping M C OGEM
systems
31.38.01.29 Dec. 1997 Pipe supports M C 07/2000 OGEM
| 31.38.01.31 Apr. 2003 Shop and field fabrication of piping T F OGEM
31.38.30.11 Dec. 1997 Protective steam heating of piping M C 51/2001 OGEM
systems
31.38.60.10 Dec. 1998 Hot-tapping on pipelines, piping and M C 66/99 EPT-PR
equipment
31.38.70.24 Withdrawn Design and installation of glass-fibre
reinforced epoxy and polyester piping
(31.40.10.19)
31.38.70.25 Withdrawn Fabrication and installation of
thermoplastics piping systems
(31.38.01.11)
31.38.70.34 Withdrawn Requirements for glass-fibre reinforced
epoxy pipes and fittings (31.38.70.37)
polyester pipes and fittings
(31.38.70.37)
31.38.70.36 Withdrawn Requirements for thermoplastics pipes
and fittings (31.38.01.11)
epoxy and polyester pipes and fittings
(31.40.10.19)
31.38.82.31 Sep. 2002 PTFE bellows T F OGEI
31.40.00.10 Nov. 1993 Pipeline engineering M C 16/2000, EPT-PR
12/2002
| 31.40.00.19 Apr. 2003 Corrosion mitigation strategy for wet M C OGEI
sour gas carbon steel pipelines
31.40.10.10 Dec. 1999 Riser design M F 16/2002 EPT-PR
31.40.10.12 Jul. 1998 Design of multiple-slug catchers M F 17/2002 EPT-PR
31.40.10.13 Dec. 1998 Design of pipeline pig trap systems T F 18/2002 EPT-PR
31.40.10.14 Mar. 1994 Pipeline overpressure protection M C EPT-PR
31.40.10.15 Dec. 1997 Analysis of spans for submerged M C EPT-PR
pipelines
31.40.10.16 Dec. 1998 Upheaval buckling of pipelines M C EPT-PR
31.40.10.17 Dec. 1997 Pipeline/trawlgear interaction M C EPT-PR
| 31.40.10.19 Dec. 1998 GRP Pipelines and piping systems M F 60/99, OGEI
(amendments/supplements to UKOOA 31/2001,
documents) 26/2003
31.40.10.31 Withdrawn Glass fibre reinforced plastic pipes and
fittings (amendments/supplements to
API Spec 15HR) (31.40.10.19)
31.40.20.30 Withdrawn Linepipe for use in oil and gas
operations under non-sour conditions
(amendments/supplements to API
Spec 5L) (31.40.20.35, 31.40.20.37)
PTS 00.00.05.05
April 2003
Page 26

Circular
No.
31.40.20.31 Withdrawn Linepipe for use in oil and gas

operations under sour conditions
API Spec 5L)
(31.40.20.35, 31.40.20.37)
31.40.20.32 Oct. 1995 CRA clad or lined steel pipe T F 25/2002 OGEI
API Spec 5LD)
31.40.20.33 Sep. 2002 Linepipe induction bends T F OGEI
15590-1)
31.40.20.34 Dec. 1998 Welded and seamless duplex and T F OGEI
super duplex stainless steel line pipe
Spec 5LC)
31.40.20.35 Dec. 1999 Linepipe for non-critical service T F 19/2002 OGEI
3183-1)
31.40.20.36 Mar. 2001 Weldable martensitic stainless steel T F OGEI
line pipe for use in oil and gas
operations (amendments/supplements
to API spec 5LC)
31.40.20.37 Dec. 2000 Linepipe for critical service T F OGEI
3183-3)
31.40.21.30 Dec. 1995 Pipeline fittings T F 20/2002 OGEI
MSS SP-75)
31.40.21.31 Dec. 1999 Pipeline isolating joints T F EPT-PR
MSS SP-75)
31.40.21.32 Withdrawn Pig trap end closures
(amendments/supplements to MSS
SP-75) (31.40.10.13)
31.40.21.33 Sep. 2002 Pig signallers - intrusive type T F EPT-PR
31.40.21.34 Jul. 1998 Carbon and low alloy steel pipeline M F 61/99, OGEI
flanges for use in oil and gas 24/2002
operations (amendments/supplements
to MSS SP-44)
31.40.30.30 Dec. 1999 Concrete coating of linepipe T C EPT-PR
| 31.40.30.31 Apr. 2003 External polyethylene and T F OGEI
polypropylene coating for line pipe
| 31.40.30.32 Apr. 2003 External fusion-bonded epoxy powder T F OGEI
coating for line pipe
31.40.30.33 Oct. 2001 Bituminous enamel coating of steel T F OGEI
linepipe
31.40.30.34 Dec. 1999 Thermoplastic lined pipelines T F 05/2002 OGEI
31.40.30.35 Jul. 1998 Internal coating of line pipe for non- T F OGEI
corrosive gas transmission service
(amendments/supplements to API RP
5L2)
| 31.40.30.36 Apr. 2003 Polychloroprene riser coatings T F OGEI
31.40.40.38 Jun. 1993 Hydrostatic pressure testing of new T C 54/2002 EPT-PR
pipelines
PTS 00.00.05.05
April 2003
Page 27

Circular
No.
31.40.50.30 Oct. 1994 Precommissioning of pipelines T C EPT-PR

31.40.60.11 Sep. 2002 Pipeline leak detection M C EPT-PR
31.40.60.12 Dec. 1995 Pipeline Repairs (supplements to M C 21/2002 OGEI
ANSI/ASME B31.4 and B31.8)
31.40.70.30 Dec. 1997 Quarter-turn on/off actuators M F OGLA
31.46.00.31 Jul. 1997 Acoustic insulation for piping T F 17/2000 OGEM
31.51.10.31 Dec. 1998 Side-entry mixers for storage tanks T F OGUF
and vessels
31.76.10.10 Jul. 1998 Heating, ventilation and air M C OGEC
conditioning for plant buildings
31.76.10.11 Dec. 1999 Installation, testing and balancing, and M C OGEC
commissioning of HVAC systems
32.00.00.10 Withdrawn The division of responsibilities between
instrument and electrical engineering
disciplines
32.00.00.11 Jul. 1997 Human-machine interface in a control M C OGLA
room
32.10.03.10 Jul. 1999 Instrument symbols and identification M F 57/2001 OGLA
on process engineering flow schemes
32.10.03.11 Withdrawn Symbols and identification system -
Instrumentation. Part 2:
- Functional logic diagrams
(32.10.03.10)
32.10.03.12 Withdrawn Symbols and identification system -
Instrumentation. Part 3:
- Instrumentation loop diagrams
(32.10.03.10)
32.24.20.30 Jul. 1997 Control system and instrumented T C 56/97 OGEH
protective functions for fired equipment
- System for a single-burner furnace
(S 24.024 and S 24.026)
32.24.20.33 Dec. 1998 Control system and instrument T C OGEH
System for an automatically started,
gas fired, natural draught, multi-burner
furnace, safeguarded by pilot burners
(S 24.033)
32.24.20.37 Jan. 1998 Control system and instrumented M C OGEH
- System for a manually-started, forced
draught, multi-burner furnace or boiler
(S 24.021)
- System for an automatically-started,
forced draught, multi-burner furnace or
boiler (S24.030 or S 24.034)
- System for a tangentially gas-fired
CO boiler (S 24.036)
| 32.24.20.42 Apr. 2003 Control system and instrumented T F OGEH
- Systems for co-fired gas turbine
waste heat recovery units
PTS 00.00.05.05
April 2003
Page 28

Number issue Title Type use by Circular
No.
32.30.10.30 Withdrawn System cabinets
32.30.20.11 Sep. 2002 Fire, gas and smoke detection M C OGLA
systems
32.31.00.10 Jul. 1985 Instrument engineering procedures M C 57/95, OGLA
43/99,
65/2001
32.31.00.32 Jul. 1999 Instruments for measurement and M C 52/2001 OGLA
control
32.31.00.34 Dec. 1995 Instrumentation documents and T F 39/99, OGLA
drawings 53/2001
32.31.09.31 Nov. 1995 Instrumentation for equipment P C 40/99, OGLA
packages 46/2001
| 32.31.50.10 Apr. 2003 On-line process stream analysis M C OGLA
- Sample take-off and transportation
32.31.50.11 Sep. 2002 On-line process stream analysis M F OGLA
- Sample conditioning
| 32.31.50.12 Apr. 2003 On-line process stream analysis – M C OGLA
Analysers
32.31.50.13 Jan. 1998 On-line process stream analysis M C 11/2000 OGLA
- Analyser houses
32.31.50.31 Withdrawn On-line process stream analysers
32.32.00.11 Sep. 2002 Turbine fiscal metering systems for T C OGUM
liquid hydrocarbons
32.32.00.12 Dec. 1999 Fiscal flow measurement of natural T F OGUM
gas
32.32.10.10 Withdrawn Flow instruments
(32.31.00.32)
32.36.01.16 Withdrawn Sizing of control valves (32.36.01.17)
| 32.36.01.17 Apr. 2003 Control valves - selection, sizing and M F OGLA
specification
32.37.00.33 Withdrawn Mounting of plant instruments
(32.31.00.32)
32.37.10.11 Oct. 2001 Installation of on-line instruments M C OGLA
32.37.10.31 Withdrawn Prefabricated instrument consoles
(32.30.10.30, now also withdrawn with
no replacement)
32.37.10.34 Withdrawn Instrument nameplates (32.31.00.32)
32.37.20.10 Jul. 1999 Instrument signal lines M C 02/2001 OGLA
32.37.20.31 Dec. 1997 System cabling T F 66/2001 OGLA
32.37.51.11 Jul. 1985 Instrument air lines M C 48/99, OGLA
55/2001
32.45.10.10 Dec. 1994 Instrumentation of depressuring M C 60/95, OGLA
systems 62/99
32.71.00.10 Jul. 1998 Plant telecommunication M C EPT-IO
32.71.00.11 Jul. 1996 Telecommunication standards M C EPT-IO
32.71.00.12 Apr. 1993 Telecommunications for offshore M C EPT-IO
platforms
32.71.00.13 Oct. 1995 Drilling communications M C EPT-IO
32.71.00.14 Jul. 1996 Telecommunications towers and M F EPT-IO
guyed masts
PTS 00.00.05.05
April 2003
Page 29

No.
32.71.00.16 Dec. 1997 Design and installation of telephone M C EPT-IO
cabling
32.71.00.30 Dec. 1998 Structured cabling systems for T F EPT-IO
telecommunications
32.71.00.31 Dec. 1997 Microwave systems M C EPT-IO
32.80.10.10 Oct. 2001 Classification and implementation of M C OGLA
instrumented protective functions
32.80.10.12 Oct. 2001 Management of instrumented M C OGLA
protective functions
32.80.10.30 Jul. 1996 Instrumented protective systems T F OGLA
33.10.03.10 Withdrawn Symbols and identification system –
Electrical
| 33.64.10.10 Sep. 2002 Electrical engineering guidelines M C 25/2003 OGEE
33.64.10.11 Jan. 1999 Electrical network monitoring and M C OGEE
control system - application
33.64.10.12 Jan. 1999 Electrical supply and generation - M C OGEE
design and operation
33.64.10.32 Jan. 1999 Electrical network monitoring and M C OGEE
control system - specification
33.64.10.33 Sep. 2002 Electromagnetic compatibility (EMC) M C OGEE
requirements
33.64.10.30 Withdrawn Electric power and lighting installations
(33.64.10.10)
| 33.65.11.31 Jan. 1999 Synchronous AC machines T F 17/2003 OGEE
IEC 60034-1)
| 33.65.11.32 Apr. 2003 Packaged unit AC generator sets T F OGEE
33.65.40.31 Oct. 2001 Power transformers T F OGEE
IEC 60076 and IEC 60726)
33.65.50.31 Dec. 2000 Static DC uninterruptible power supply T F OGEE
(DC UPS) units
33.65.50.32 Dec. 1998 Static AC uninterruptible power supply T F OGEE
unit (Static AC UPS unit)
33.66.05.10 Withdrawn Engineering guidelines variable speed
drive systems (technique and
applications)
33.66.05.31 Jan. 1999 Electric machines - Cage-induction T F OGEE
types
(Amendments/supplements to IEC
60034-1)
33.66.05.33 Mar. 1995 Electrical variable speed drive systems T F OGEE
33.67.01.31 Jan. 1998 Low-voltage switchgear and T F OGEE
controlgear assemblies
IEC 439-1)
33.67.51.31 Jul. 1998 High-voltage switchgear and T F OGEE
controlgear assemblies
(amendments/supplements to IEC
298)
33.68.30.31 Oct.2001 Electrical heating system for frost T F OGEE
heave prevention of refrigerated
hydrocarbon storage tanks
33.68.30.32 Dec. 2000 Electrical trace heating T F OGEE
PTS 00.00.05.05
April 2003
Page 30
PTS Date of PTS Intended Amended by Custodian

Number issue Title Type use Circular No.
33.68.30.33 Oct. 2001 Electrical process heaters T F OGEE
33.80.00.30 Aug. 2000 Navigational aids for offshore T F OGEE
structures
34.00.01.30 Jul. 1998 Minimum requirements for structural T C OGEC
design and engineering
34.11.00.10 Dec. 1999 Site investigations M C OGEC
| 34.11.00.11 Apr. 2003 Site preparation and earthworks M C OGEC
including tank foundations and tank
farms
34.11.00.12 Apr. 1987 Geotechnical and foundation M C OGEC
engineering
| 34.13.20.31 Apr. 2003 Roads, paving, surfacing, slope T C OGEC
protection and fencing
| 34.14.20.31 Dec. 1993 Drainage and primary treatment T C 59/2001, OGEC
facilities 41/2003
| 34.17.00.32 Sep. 2002 Minimum requirements for design and T C 19/2003 OGEC
engineering of buildings
34.17.10.30 Sep. 2002 Reinforced control buildings/Field T C OGEC
auxiliary rooms
34.17.10.31 Dec. 1996 Laboratories T C OGEC
| 34.18.51.10 Withdrawn Minimum requirements for the
construction and maintenance of tank
foundations, bund walls and drainage
systems for small storage installations
(34.11.00.11)
34.19.20.11 Dec. 1999 Fireproofing of steel structures M C OGEC
34.19.20.31 Dec. 1998 Reinforced concrete foundations and T C 09/2000, OGEC
structures 09/2002
| 34.24.26.31 Apr. 2003 Steel stacks T C OGEC
(amendments/supplements to CICIND
Model Code)
34.24.27.31 Dec. 1999 Reinforced concrete stacks T C OGEC
34.28.00.31 Jul. 1996 Steel structures T C OGEC
34.51.01.31 Sep. 1992 Standard vertical tanks - Selection, T F OGEC
design and fabrication
34.51.11.30 Oct. 2001 Mounded horizontal cylindrical vessels T F OGEC
for pressurised storage of LPG at
ambient temperatures (endorsement of
EEMUA publication No. 190)
34.51.90.10 Sep. 2002 Demolition of storage tanks M C OGEC
(endorsement of EEMUA 154)
34.76.30.31 Withdrawn Heating and air conditioning in sub-
stations and switch houses
(31.76.10.10)
37.05.10.10 Sep. 2002 Design of sea water systems and utility M F OGUD
heat transfer systems for offshore
installations
37.05.10.11 Dec. 1998 Diesel oil systems in oil and gas M C OGUD
production facilities
37.05.10.12 Aug. 2000 Design of hose bulk transfer facilities M F OGUD
for offshore installations
PTS 00.00.05.05
April 2003
Page 31
PTS Date of PTS Intended Amended by Custodian

Number issue Title Type use Circular No.
37.11.00.30 Dec. 1994 Site specific assessment of mobile P C EPT-PB

offshore jack-up units
(amendments/supplements to the
SNAME guideline and recommended
practice)
37.14.10.10 Dec. 1998 Drain systems for offshore installations M C OGUD
37.17.10.10 Dec. 1998 Design of offshore living quarters M F OGUD
37.17.10.11 Mar. 1994 Design of offshore temporary refuges M C OGCH/1
37.19.00.30 Mar. 1994 Design of steel substructures for fixed P C EPT-PB
offshore platforms
(amendments/supplements to API RP
2A-LRFD)
37.19.10.30 Feb. 1993 Weldable structural steels for fixed T F EPT-PB
offshore structures
(amendments/supplements to BS
7191)
37.19.30.30 Dec. 1995 Design of cathodic protection T F OGEI
systems for new fixed offshore steel
structures
(amendments/supplements to DNV
RP B401)
37.19.60.10 Oct. 2001 Structural inspection of offshore M C EPT-PB
installations
37.29.01.10 Dec. 1998 Firewater pumps for offshore M F OGER
installations
37.80.00.30 Aug. 2000 Subsea production systems T F EPT-PB
(endorsement of ISO 13628 and API
17 series)
37.91.10.11 Jul. 1998 Mooring of mobile units M C EPT-PB
37.91.20.30 Aug. 2000 Oil loading and discharge hoses for T F OGEI
offshore mooring installations
(Amendments/supplements to OCIMF
Guide)
37.92.10.30 Oct. 1994 Pedestal cranes T F 13/2002 OGUD
Spec 2C)
37.92.10.31 Oct. 1994 Pedestal cranes T F 14/2002 OGUD
(amendments/supplements to Lloyd's
code and BS 2573)
38.80.10.30 Dec. 1999 Drilling fluid material - specifications T F EPGO-W
and tests (Endorsement of ISO 13500)
38.80.10.31 Sep. 2002 Field testing of drilling fluids - water- T F EPGO-W
based fluids (endorsement of ISO
10414-1)
| 38.80.10.32 Apr. 2003 Field testing of drilling fluids – Oil T F EPGO-W
based fluids (amendments/
supplements to ISO 10414-2)
38.80.20.30 Mar. 2001 Specifications for cements and T F EPGO-W
materials for well cementing
(endorsement of ISO 10426-1)
39.01.10.11 Sep. 2002 Selection of materials for life-cycle M F OGEI/2
performance (EP)
39.01.20.10 Oct. 1995 L80 13%Cr casing and tubing T F EPGO-W
(amendments/supplements to ISO/DIS
11960.2)
PTS 00.00.05.05
April 2003
Page 32

No.
39.01.20.30 Dec. 2000 Corrosion-resistant alloy seamless T F EPGO-W

tubes for use as casing, tubing and
coupling stock - technical delivery
conditions (endorsement of ISO 13680)
39.01.20.31 Dec. 2000 Care and use of casing and tubing T F EPGO-W
(endorsement of ISO 10405)
39.01.30.30 Oct. 2001 Wellhead and christmas tree T F EPGO-W
equipment (amendments and
supplements to ISO 10423)
39.01.30.31 Aug. 2000 Downhole equipment - Sub-surface T F EPGO-P
safety valves (endorsement of ISO
10432)
39.40.20.30 Withdrawn High pressure metal/polymer flexible
pipe for use in oil and gas operations
as flowlines and risers (37.80.00.30)
40.10.01.11 Dec. 1997 Capital project coding system M C OGPS
40.10.10.41 Withdrawn List of approved suppliers of
longitudinally welded stainless pipes
and tubes
40.10.21.40 Withdrawn List of approved suppliers of seamless
aluminium brass condenser/cooler
tubes
40.10.40.40 Withdrawn List of approved oil-resistant CAF
compound jointing
40.10.40.41 Withdrawn List of approved acid-resistant CAF
compound jointing
40.10.40.42 Withdrawn List of approved spiral-wound gaskets
40.10.50.41 Withdrawn List of approved suppliers of 1 Cr-0.25
Mo steel bolts and medium carbon
steel nuts
40.10.64.10 Withdrawn Welding electrodes, rods wires and
fluxes
40.48.00.30 Withdrawn Paints and paint materials
(30.48.00.31, 70.48.10.10)
41.20.20.31 Withdrawn Purchasing procedure trays for
columns (MA-13)
41.21.01.30 Withdrawn Purchasing procedure unfired shell
and tube heat exchangers (MA-11)
41.21.06.40 Withdrawn List of approved suppliers of 12 Cr
steel bolting for floating heads of heat
exchangers
41.21.70.31 Withdrawn Air cooled heat exchangers -
purchasing procedure
41.24.49.31 Withdrawn Shop fabrication of heater piping -
purchasing procedure
41.38.01.31 Withdrawn Purchasing procedure shop fabrication
of steel piping (MA-05)
42.31.31.30 Withdrawn Purchasing procedure signal light
assemblies
44.24.90.31 Mar. 2001 Refractory bricks and shapes M C 32/2001 OGEC
44.28.00.31 Withdrawn Purchasing procedures steel structures
(MA-12)
44.51.01.31 Withdrawn Purchasing procedure standard
vertical tanks (MA-07)
PTS 00.00.05.05
April 2003
Page 33

No.
61.10.08.11 Jul. 1999 Field inspection prior to commissioning M C 03/2001 OGCC
of mechanical equipment
61.22.01.31 Withdrawn Rotating disc contactors - Installation,
site testing and maintenance
(31.22.01.31)
61.24.15.31 Withdrawn SIPM-type vertical furnaces and waste
heat boilers - Field erection
61.38.10.10 Dec. 1999 Shop and field fabrication of orifice T F OGEM
meter runs
61.40.20.30 Jun. 1993 Welding of pipelines and related T C 20/2000 OGEI
facilities(amendments/supplements to
ANSI/API STD 1104)
61.40.20.31 Jul. 1999 Field welding of duplex and super T C OGEI
duplex stainless steel pipelines
1104)
| 62.10.08.11 Dec. 1997 Inspection and functional testing of P C 20/2003 OGLA
instruments
62.10.09.11 Withdrawn Factory inspection and testing of
instruments and instrument systems
(62.10.08.11)
62.37.10.12 Withdrawn Instrument installation procedures
63.10.08.11 Aug. 2000 Field commissioning and maintenance M F OGEE
of electrical installations and
equipment
64.11.10.31 Withdrawn Site preparation (34.11.00.11)
| 64.24.32.11 Dec. 1999 Refractory materials for sulphur M C 39/2003 OGEC
recovery units (claus and scot)
64.24.32.30 Dec. 1997 Insulating and dense refractory M C 10/2002 OGEC
concrete linings
64.51.01.31 Dec. 1995 Standard vertical tanks - Field erection T C OGEC
and testing
70.07.20.30 Withdrawn Magnetic particle inspection of the
threaded parts of steel drill stem
70.08.10.10 Withdrawn Equipment and tools for maintenance
and inspection. Part 1:
- Inspection -
Tools and NDT instruments
70.08.10.11 Dec. 1998 Equipment and tools for maintenance M C OGCC
- Mechanical maintenance equipment,
tools and bolt tensioning
70.08.10.12 Withdrawn Equipment and tools for maintenance
- Mechanical maintenance - Tools
(70.08.10.11)
70.08.10.13 Dec. 1992 Equipment and tools for maintenance M C 08/95, OGEE
and inspection. Part 4: 17/95
- Electrical workshop - Test equipment
and tools
| 70.08.10.14 Withdrawn Equipment and tools for maintenance
- Instrument technical centre and
workshop- Equipment and tools
70.10.01.10 Jul. 1999 Equipment record cards M C OGCC
PTS 00.00.05.05
April 2003
Page 34

No.
70.10.70.11 Jul. 1999 The preservation of old and new M C OGCC
equipment and piping standing idle
70.10.80.11 Jan. 1998 Cleaning of equipment M C OGUF
70.10.90.11 Sep. 2002 Spare parts M F OGEM
70.48.10.10 Dec. 1995 Maintenance painting M F OGEI
70.51.10.11 Jul. 1998 Field inspection, maintenance and M G OGEC
repair of vertical steel storage tanks
74.04.12.15 Withdrawn Testing methods for stored cat. cracker
refractories
74.36.10.31 Withdrawn Testing of soft seat ball valves
designed in accordance with BS
5351
74.36.10.32 Withdrawn Design and evaluation of rubber
lined butterfly valves for fire
protection service
80.00.10.10 Dec. 1995 Area classification M C 56/2001 OGCH/1
(amendments/supplements to IP 15)
80.36.00.30 Mar. 2001 Relief valves - selection, sizing and T C OGEM
specification
80.45.10.10 Jul. 1996 Pressure relief, emergency M C 32/98 OGEM
depressuring, flare and vent systems
80.46.30.11 Dec. 1999 Interlocking systems for safety/relief M C 43/2002 OGEM
valves
80.47.10.10 Withdrawn Fire-fighting agents (80.47.10.32)
80.47.10.11 Withdrawn Fire-fighting systems (80.47.10.30)
80.47.10.12 Dec. 1997 Water-based fire protection systems M F 13/2000 OGCH/1
for offshore facilities
80.47.10.30 Jan. 2000 Assessment of the fire safety of M C OGCH/1
onshore installations
80.47.10.31 Dec. 1999 Active fire protection systems and M C OGCH/1
equipment for onshore facilities
80.47.10.32 Jan. 2000 Fire-fighting agents and movable fire T F OGCH/1
fighting equipment for onshore
applications
| 80.47.10.33 Dec. 1999 Fire-fighting vehicles and fire stations T F 32/2003 OGCH/1
80.47.20.30 Withdrawn Trucks and trailers for fire-fighting
80.80.00.10 Dec. 1998 Offshore facilities life-saving appliance M F OGCH/1
requirements
(amendments/supplements to SOLAS)
80.80.00.11 Sep. 2002 Control and mitigation of fires and M F OGCH/1
explosions on offshore production
installations
13702)
80.80.00.12 Sep. 2002 Offshore production installations - M F OGCH/1
Requirements and guidelines for
emergency response
15544)
PTS 00.00.05.05
April 2003
Page 35

No.
80.80.00.13 Sep. 2002 Offshore production installations - M F OGCH/1

Guidelines on tools and techniques for
identification and assessment of
hazardous events
17776)
82.00.10.10 Dec. 1995 Project quality assurance M F 24/98 OGPS
82.00.10.11 Aug. 2000 Cost control of capital investment M F OGPS
projects
PTS 00.00.05.05
April 2003
Page 36
2. STANDARD SPECIFICATIONS
Spec. Date of
Number issue Title
A-1-1 Withdrawn Process units eral
A-2-1 Withdrawn Process control and instrumentation requirements
A-3-1 Withdrawn Pressure relief valves (80.45.10.10)
A-4-1 Withdrawn Fuel systems (20.05.60.10)
A-5-1 Withdrawn Hot-oil systems (20.05.50.10)
A-6-1 Withdrawn Waste gas and low-pressure (LP) gas disposal systems
A-11-1 Withdrawn Crude distilling units
A-12-1 Withdrawn High vacuum distilling units
A-13-1 Withdrawn Catalytic reforming and hydrotreating/hydrodesulphurizing units
A-14-1 Withdrawn Catalyst reforming units
A-15-1 Withdrawn Hydrotreating and hydrodesulphurizing units
A-16-1 Withdrawn Bitumen blowing units
A-17-1 Withdrawn Sulphur recovery units
A-18-1 Withdrawn Thermal cracking units
B-1-1 Withdrawn Buildings General (34.17.00.32)
B-2-1 Withdrawn Control room building (34.17.10.30)
B-3-1 Withdrawn Laboratory (34.17.10.31)
B-10-2 Withdrawn Specification for supply/erection of "heating, ventilating and air conditioning plants" in
buildings (31.76.10.11)
B-11-1 Withdrawn Heating, ventilating and air conditioning in control centres (31.76.10.10)
B-12-1 Withdrawn Heating, ventilating and air conditioning in building: sub-stations and switch houses
(34.76.30.31, now 31.76.10.10)
B-12-2 Withdrawn Heating, ventilating and air conditioning in reinforced control building (31.76.10.10)
C-1-1/2/3 Withdrawn Rotating disc contactors (31.22.01.31)
C-2-1 Withdrawn Trays for columns (31.20.20.31)
D-1-1 Withdrawn Compilation of design books (01.00.02.11)
Dr-1-2/3 Withdrawn C-95 casing and tubing for sour (H2 S) service (quench and temper process)
E-1-1 Withdrawn Unfired heat transfer equipment (31.21.01.30, 31.21.70.31)
E-1-3 Withdrawn Minimum requirements for the shop checking, inspection and testing of
unfired heat transfer equipment (31.21.01.30, 31.21.70.31)
F-1-1 Withdrawn Furnaces and related equipment (31.24.00.30)
E-2-3 Withdrawn Minimum requirements for the shop checking, inspection and testing of coil-wound heat
exchangers (31.21.01.30)
G-1-1 Withdrawn Fabrication report for pressure vessels (31.2210.35)
G-2-1 Withdrawn Model construction (30.10.05.11)
G-3-1 Withdrawn Asset breakdown (01.00.09.10)
G-5-1 Withdrawn Job procedures manual
G-6-2 Withdrawn Specification for the preparation and micro-filming of technical drawings (02.00.00.10)
G-7-1 Withdrawn Descriptive index for a Shell Project Specification
G-8-1 Withdrawn Fire-proofing of steel structures (34.19.20.11)
H-1-1 Withdrawn Piling
H-2-1 Withdrawn Reinforced concrete foundations and structures (34.19.20.31)
H-3-1 Withdrawn Reinforced concrete stacks (34.24.27.31)
PTS 00.00.05.05
April 2003
Page 37
Spec. Date of
Number issue Title
In-1-1 Withdrawn Instrumentation
(32.31.00.10, 32.31.00.32)
In-2-1 Withdrawn The instrumentation of depressuring systems (32.45.10.10)
In-3-1 Withdrawn Control valves (32.36.01.17)
In-5-1 Withdrawn Instrumentation for package units (32.30.20.11)
K-1-1 Withdrawn Compressor selection (31.29.40.10)
K-3-2/3 Withdrawn Rotary-type positive displacement compressors mechanical design, construction and
testing (31.29.40.32)
K-4-2/3 Withdrawn Reciprocating compressors - mechanical design, construction and testing (31.29.40.31)
K-5-3 Withdrawn Checking, testing and inspection of fans (31.29.47.30)
K-6-2 Withdrawn Lube and seal oil systems for special purpose applications (31.29.60.32)
L-1-1 Withdrawn Piping (31.38.01.11)
L-2-2/3 Withdrawn Line pipe for use in oil and gas operations under non-sour conditions (31.40.20.30)
L-3-2/3 Withdrawn Line pipe for use in oil and gas operations under sour conditions (31.40.20.31)
L-4-1/2/3 Withdrawn External polyethylene coating for line pipe (31.40.30.31)
L-5-1/2/3 Withdrawn External fusion-bonded epoxy powder coating for line pipe (31.40.30.32)
M-1-1 Withdrawn Spare parts (70.10.90.11)
N-1-1 Withdrawn Electric power and lighting installations (33.64.10.10)
N-2-1 Withdrawn Telecommunication (32.71.00.10)
N-3-3 Withdrawn Inspection and testing of LV switchgear and controlgear (33.67.01.31)
O-1-1 Withdrawn Jointing material (31.38.01.11)
O-2-1 Withdrawn Thermal insulation for hot services (30.46.00.31)
O-3-1 Withdrawn Thermal insulation for cold service and dual temperature
P-1-1 Withdrawn Pumps selection (31.29.02.11)
P-1-2/3 Withdrawn Centrifugal pumps - mechanical design and construction, shop inspection and tests
(31.29.02.30)
P-4-3 Withdrawn Checking, testing and inspection of rotary pumps (screw pumps)
P-5-3 Withdrawn Checking, testing and inspection of positive displacement pumps (reciprocating type)
(31.29.12.30)
Q-1-1 Withdrawn Site preparation (34.11.00.11)
Q-2-1 Withdrawn Drainage and sewerage system (34.14.20.31)
Q-3-1 Withdrawn Roads, paving and fencing (34.13.20.31)
R-1-1 Withdrawn Reactors
S-2-3 Withdrawn Min requirements for shop checking inspection and testing of loading arms
S-3-3 Withdrawn Minimum requirements for the shop checking, inspection and testing of closed thimble
circular nylon mooring ropes
S-4-3 Withdrawn Minimum requirements for the shop checking, inspection and testing of a SBM (single
buoy mooring)
ST-1-1 Withdrawn Steam turbine selection (31.29.60.10)
ST-2-2/3 Withdrawn General purpose steam turbines (mechanical design and construction, shop inspection
and tests) (31.29.60.30)
T-1-1 Withdrawn Storage tanks (64.51.01.31, 70.51.10.11)
T-2-1 Withdrawn LPG storage facilities (30.06.10.12)
U-3-1 Withdrawn Painting and coating of new construction projects (30.48.00.31)
U-4-1 Withdrawn Cathodic protection (30.10.73.10)
PTS 00.00.05.05
April 2003
Page 38
Spec. Date of
Number issue Title
V-1-1/2/3 Withdrawn Pressure vessels (31.22.10.32, 31.22.20.31)
V-2-3 Withdrawn Minimum requirements for the shop checking, inspection and testing of unfired pressure
vessels other than shell and tube type heat exchange equipment (31.22.10.32,
31.22.20.31)
V-3-2 Withdrawn LPG storage vessels (31.22.10.36, now 30.06.10.12 and 31.22.10.32)
V-4-1 Withdrawn Gas/liquid separators (31.22.05.11)
V-5-1 Withdrawn Hydrogen and nitrogen storage bottles for platformer units (31.22.90.30)
W-1-1 Withdrawn Field inspection
W-2-3 Withdrawn Minimum requirements for the shop checking, inspection and testing of cat. cracker
cyclones and accessories
W-3 Withdrawn Minimum requirements for the shop checking, inspection and testing of rotary vacuum
filters
W-4-1/2/3 Withdrawn Welding and inspection requirements for equipment not covered by recognized standards
and/or codes
W-5-1/2/3 Withdrawn Repair by welding of aluminium and aluminium-alloy castings
W-6-1/2/3 Withdrawn Equipment made of 2.25 Cr - 1 Mo steel in quenched and tempered condition
(30.10.02.32)
W-7-1/2/3 Withdrawn Aluminium-bronze sand castings (amendments/supplements to ASTM B 148)
Y-1-1 Withdrawn Steel structures (34.00.01.30)
Y-2-1 Withdrawn Steel stacks (34.24.26.31)
Z-1-1 Withdrawn Fire-fighting systems (80.47.10.30, 80.47.10.31)
Z-2-1 Withdrawn Noise specification for plant and equipment (31.10.00.31)
Last page of this PTS

Petronas Technical Standards: Pts Publications and Standard Specifications

Uploaded by

Copyright:

Available Formats

Petronas Technical Standards: Pts Publications and Standard Specifications

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Petronas Technical Standards: Pts Publications and Standard Specifications

Uploaded by

Copyright:

Available Formats

PETRONAS TECHNICAL STANDARDS

DESIGN AND ENGINEERING PRACTICE

PTS PUBLICATIONS AND STANDARD

The right to use PTS rests with three categories of users :

1) PETRONAS and its affiliates.

1.2 TYPES OF PTS

1.3 STANDARD SPECIFICATIONS

1.4 REQUISITIONS AND STANDARD FORMS

1.5 DISTRIBUTION OF PTSs

EPGO-F Vanderaar, L Rijswijk # 31 70 447 4030 leo.vanderaar@shell.com

EPGO-P Helmer, T Rijswijk # 31 70 447 6367 T.Helmer@shell.com

EPTO-W Brouwer, S Rijswijk # 31 70 447 2062 sjoerd.brouwer@shell.com

EPT-IO Akkermans, F Rijswijk # 31 70 447 3860 frans.akkermans@shell.com

EPT-PB Reece, A.M Houston # 1 713 245 7437 allan.reece@shell.com

EPT-PR Oude Hengel, J Rijswijk # 31 70 311 6049 j.oudehengel@shell.com

OGCC Aarten, T. The Hague #31 70 377 6032 thijs.aarten@shell.com

OGCH/1 Pescott, R.D. The Hague #31 70 377 1484 dick.pescott@shell.com

OGCH/2 Heard, N Chester # 44 151 373 5040 nigel.heard@shell.com

OGEC Krijn, P The Hague # 31 70 377 1828 pieter.krijn@shell.com

OGEE Griffin, P.T. The Hague # 31 70 377 3149 terry.griffin@shell.com

OGEH Bosch, S. Amsterdam # 31 20 630 3140 sjoerd.bosch@shell.com

OGEI/1 Lewis, K. Amsterdam #31 20 630 3147 keith.k.r.lewis@shell.com

OGEI/2 Kerkveld, G. Amsterdam # 31 20 630 2438 gert.kerkveld@shell.com

OGEI/4 Hummel, R. Houston #1 281 544 7616 rjhummel@shell.com

OGEM Mes, H. The Hague # 31 70 377 3977 hans.mes@shell.com

OGGL Pek, B. The Hague # 31 70 377 1951 barend.pek@shell.com

OGLA van Geel, C.A.G. The Hague # 31 70 377 2026 cees.vangeel@shell.com

OGPS Bakker, H The Hague # 31 70 377 2136 hans.h.l.m.bakker@shell.com

OGRD van Wijk, R. Amsterdam # 31 20 630 2044 ron.vanwijk@shell.com

OGLM Jagannathan, A. The Hague # 31 70 377 6268 jag.j.jagannathan@shell.com

OGRC Muller, F Amsterdam # 31 20 630 2375 fred.muller@shell.com

OGRT Schrijvers, F.A.M. Amsterdam # 31 20 630 2734 frans.schrijvers@shell.com

OGRU Vasmel, H. Amsterdam # 31 20 630 2472 henk.vasmel@shell.com

OGUA Leitko, A Houston # 1 281 544 7937 alan.leitko@shell.com

OGUD Mossman, J. Rijswijk # 31 70 311 3553 john.mossman@shell.com

OGUF Colenbrander, G.W. Amsterdam # 31 20 630 3384 gert.colenbrander@shell.com

OGUM Jakeman, S. Rijswijk # 31 70 311 3514 simon.jakeman@shell.com

PART I SUBJECT INDEX

1. GENERAL ENGINEERING SUBJECTS

Title PTS Number

Index to standard drawings PTS 00.00.06.06

Heat transfer fluid (HTF) systems PTS 20.05.50.10

Symbols and identification system – Mechanical PTS 31.10.03.10

Gaseous oxygen systems PTS 31.10.11.31

2.2.1 General/noise/safety relief systems

Water-tube boiler installations PTS 30.75.10.30

Gas turbine heat recovery steam generators PTS 30.75.10.31

2.2.3 Heat exchangers

2.2.5 Rotating equipment

2.2.6 Piping and pipelines

Side-entry mixers for storage tanks & vessels PTS 31.51.10.31

Piping classes - basis of design PTS 31.38.01.10

Pipeline Repairs (supplements to ANSI/ASME B31.4 and B31.8) PTS 31.40.60.12

2.3 CONSTRUCTION MATERIALS

2.4 WELDING, GENERAL

Welding on pressurised pipes (amendments/supplements to ANSI/API RP1107) PTS 30.10.60.30

Oxidation of stainless steel weldments PTS 30.10.60.31

2.5 MAINTENANCE AND INSPECTION

2.6 OFFSHORE APPLICATIONS