Tubular Motor Control Panel User Manual (TM5030) A5 Version A5

1. Safety Instruction 4.Product picture

1.For security, please read the instructions carefully before initial operation;making sure that the power is off before connection. 1.LED：Power,indicator light of learning
2.The received signal may be interfered by other communication devices. (e.g. the wireless control system with the same frequency range) 2.Button to learn and delete transmitter
3.It is forbidden to control the high-risk coefficient equipment / system. 3 and 5.Operated button (Open , close)
4.It should be applied in dry indoor place or in the electric appliance place. 4.Stopped button
2. Specification 5.Built-in fuse：10A 6.DIP SWITCH
1.Working voltage：220V，50HZ 6.Temperature range：-20℃ to 60℃
2.Loading capacity：0.5HP，240VAC 7.Size：93*57.5*26mm
3.Working frequency：433.92MHZ 8.Weight：125g
4.Code：Rolling code 9.Self-learning function
3. learning and deleting remotes by receiver:
1.Learn transmitter:Press the learning button on the panel,LED turns into red and gets into learning state;press the same button
twice on the same transmitter,LED blinks for a while and turns into green shows transmitter has been learned successfully. DIP:
2.Delete transmitter:Continue pressing the learning button (about 8s) until LED turns green then release the DIP 1 DIP 2
learning button, LED turns red (about 1s) then turns green. It indicates that the erasing process is successful ON Single button Latch
OFF Three button Non-latch
5.Operational process
5.1 Three button control system with transmitter and non-Latch model 7.terminal blocks
Button 1,2,3 in transmitter is in correspondence with open, close and stop. ● L\N port connects the
5.2 Three button control with transmitter and latch model ● COM \▲\▼ port connects
Motor works clockwise when keep pressing button 1;Motor works anticlockwise when keep pressing button 2;Motor stops when releasing button leading wire of motor
5.3 Single button control system and non-Latch model ● Earth wire
Press-Open(motor works clockwise), press-stop, press-close(motor works anti clockwise),press-stop,and so on in a loop.
Single-button control is only effective to the learned button; if a new button of transmitter learned into the control panel, the formal one is useless. (e.g.: if learned
button ① at first, and then button ② or ③, the former button ① becomes invalid).
5.4 Single button control and latch model
Motor works clockwise/anticlockwise when keep pressing the button; motor stops when releasing.

NOTE: 1．Single-button control refers to single button in transmitter; ▲ ■ ▼ in control panel is in correspondence with open, close and stop.
2. Max running time means that the motor’s maximum running time at a time is 100S; the motor stops immediately if longer than 100S.
3. ▲ ■ ▼ in control panel and OPEN STOP CLOSE button in transmitter are in correspondence with open, close and stop.

6.Installation Process
1. Drill 2.Install buckle 3.Install panel 4.Connection&install decorative covers
In the Fix the expansion screws, buckle and 4*25 Fix the top side of buckle to the According to the connection instruction of
installation screw on the wall; Note the direction of installation hole of the back of control control panel; when connecting, applied
position,drill buckle, fix the deep side on top (as shown in panel, the other side of buckle is in to the actual line circuit to choose the top
two φ6 picture 2) close connection with outer surface. or bottom holes of control panel;After
checking there is no errors, install the
holes with the depth of about
decorative covers;Complete the
35mm and distance is 13mm.
installation.

7,Self-learning function: Old one Old one New one

learning new remotes by old remotes

STEP3:Press the same button on the new transmitter

STEP 1:Use the trasmitter that already has been learned as
STEP2:then press button 2 to let it enters into the learning process . twice. The learning process done. In this way , new
old transmitter, press button 1 and button 2 at the same
transmitter can be learned without pressing the learning
time
button on the control board.

The interpretation and ownership of this manual belong to Hiland company. Any change of The product can be without prior notice.