Datasheet

SPRS226L − NOVEMBER 2003 − REVISED FEBRUARY 2008
Highest-Performance Fixed-Point DSPs Two External Memory Interfaces (EMIFs)

− 1.67-/1.39-/1.17-/1-ns Instruction Cycle − One 64-Bit (EMIFA), One 16-Bit (EMIFB)
− 600-/720-/850-MHz, 1-GHz Clock Rate − Glueless Interface to Asynchronous
− Eight 32-Bit Instructions/Cycle Memories (SRAM and EPROM) and
− Twenty-Eight Operations/Cycle Synchronous Memories (SDRAM,
− 4800, 5760, 6800, 8000 MIPS SBSRAM, ZBT SRAM, and FIFO)
− Fully Software-Compatible With C62x − 1280M-Byte Total Addressable External
− C6414/15/16 Devices Pin-Compatible Memory Space
− Extended Temperature Devices Available Enhanced Direct-Memory-Access (EDMA)
VelociTI.2 Extensions to VelociTI Controller (64 Independent Channels)
Advanced Very-Long-Instruction-Word Host-Port Interface (HPI)
(VLIW) TMS320C64x DSP Core − User-Configurable Bus Width (32-/16-Bit)
− Eight Highly Independent Functional
32-Bit/33-MHz, 3.3-V PCI Master/Slave
Units With VelociTI.2 Extensions:
Interface Conforms to PCI Specification 2.2
− Six ALUs (32-/40-Bit), Each Supports
[C6415T/C6416T]
Single 32-Bit, Dual 16-Bit, or Quad
− Three PCI Bus Address Registers:
8-Bit Arithmetic per Clock Cycle
Prefetchable Memory
− Two Multipliers Support
Non-Prefetchable Memory I/O
Four 16 x 16-Bit Multiplies
− Four-Wire Serial EEPROM Interface
(32-Bit Results) per Clock Cycle or
− PCI Interrupt Request Under DSP
Eight 8 x 8-Bit Multiplies
Program Control
(16-Bit Results) per Clock Cycle
− DSP Interrupt Via PCI I/O Cycle
− Non-Aligned Load-Store Architecture
− 64 32-Bit General-Purpose Registers Three Multichannel Buffered Serial Ports
− Instruction Packing Reduces Code Size − Direct Interface to T1/E1, MVIP, SCSA
− All Instructions Conditional Framers
− Up to 256 Channels Each
Instruction Set Features
− ST-Bus-Switching-, AC97-Compatible
− Byte-Addressable (8-/16-/32-/64-Bit Data)
− Serial Peripheral Interface (SPI)
− 8-Bit Overflow Protection
Compatible (Motorola)
− Bit-Field Extract, Set, Clear
− Normalization, Saturation, Bit-Counting Three 32-Bit General-Purpose Timers
− VelociTI.2 Increased Orthogonality UTOPIA [C6415T/C6416T]
VCP [C6416T Only] − UTOPIA Level 2 Slave ATM Controller
− Supports Over 833 7.95-Kbps AMR − 8-Bit Transmit and Receive Operations
− Programmable Code Parameters up to 50 MHz per Direction
− User-Defined Cell Format up to 64 Bytes
TCP [C6416T Only]
− Supports up to 10 2-Mbps or Sixteen General-Purpose I/O (GPIO) Pins
60 384-Kbps 3GPP (6 Iterations) Flexible PLL Clock Generator
− Programmable Turbo Code and IEEE-1149.1 (JTAG†)
Decoding Parameters Boundary-Scan-Compatible
L1/L2 Memory Architecture 532-Pin Ball Grid Array (BGA) Package
− 128K-Bit (16K-Byte) L1P Program Cache (GLZ/ZLZ/CLZ Suffixes), 0.8-mm Ball Pitch
(Direct Mapped)
0.09-µm/7-Level Cu Metal Process (CMOS)
− 128K-Bit (16K-Byte) L1D Data Cache
(2-Way Set-Associative) 3.3-V I/Os, 1.1-V Internal (600 MHz)
− 8M-Bit (1024K-Byte) L2 Unified Mapped 3.3-V I/Os, 1.2-V Internal (720/850 MHZ, 1
RAM/Cache (Flexible Allocation) GHz)
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
C62x, VelociTI.2, VelociTI, and TMS320C64x are trademarks of Texas Instruments.

Motorola is a trademark of Motorola, Inc.
† IEEE Standard 1149.1-1990 Standard-Test-Access Port and Boundary Scan Architecture.
!"# $ %&'# "$ (&)*%"# +"#', Copyright  2008, Texas Instruments Incorporated
+&%#$ %! # $('%%"#$ (' #-' #'!$ '."$ $#&!'#$
$#"+"+ /""#0, +&%# (%'$$1 +'$ # '%'$$"*0 %*&+'
#'$#1 "** (""!'#'$,
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443 1

Table of Contents
revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
GLZ, ZLZ and CLZ BGA packages (bottom view) . . . . . . . . 4 absolute maximum ratings over operating case
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . 76
device characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 recommended operating conditions . . . . . . . . . . . . . . . . 76
device compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 electrical characteristics over recommended ranges of
supply voltage and operating case temperature . 77
functional block and CPU (DSP core) diagram . . . . . . . . . . . 8
recommended clock and control signal transition
CPU (DSP core) description . . . . . . . . . . . . . . . . . . . . . . . . . . 9
behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
memory map summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
peripheral register descriptions . . . . . . . . . . . . . . . . . . . . . . . 15 parameter measurement information . . . . . . . . . . . . . . . 78
EDMA channel synchronization events . . . . . . . . . . . . . . . . 28 input and output clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
interrupt sources and interrupt selector . . . . . . . . . . . . . . . . 30 asynchronous memory timing . . . . . . . . . . . . . . . . . . . . . 85
signal groups description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 programmable synchronous interface timing . . . . . . . . 89
device configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 synchronous DRAM timing . . . . . . . . . . . . . . . . . . . . . . . . 94
multiplexed pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 HOLD/HOLDA timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
debugging considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 BUSREQ timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
terminal functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 reset timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
development support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 external interrupt timing . . . . . . . . . . . . . . . . . . . . . . . . . 108
device support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 host-port interface (HPI) timing . . . . . . . . . . . . . . . . . . . 109
clock PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 peripheral component interconnect (PCI) timing
[C6415T and C6416T only] . . . . . . . . . . . . . . . . . . 114
general-purpose input/output (GPIO) . . . . . . . . . . . . . . . . . . 69
multichannel buffered serial port (McBSP) timing . . . . 117
power-down mode logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 UTOPIA slave timing [C6415T and C6416T only] . . . 128
power-supply sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 timer timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
power-supply decoupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 general-purpose input/output (GPIO) port timing . . . . 132
IEEE 1149.1 JTAG compatibility statement . . . . . . . . . . . . . 74 JTAG test-port timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
EMIF device speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
bootmode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
2 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443

REVISION HISTORY
This data sheet revision history highlights the technical changes made to the SPRS226K device-specific data
sheet to make it an SPRS226L.
Scope: Applicable updates to the C64x device family, specifically relating to the C6414T/C6415T/C6416T
devices, have been incorporated.
The TMS320C6414T/C6415T/C6416T devices at all speeds now support an “M version” commercial

temperature range of 0C to 90C.
PAGE(S)
ADDITIONS/CHANGES/DELETIONS
NO.
Global − Added the M version, commercial temperature range of 0C to 90C.
Figure 5. TMS320C64x DSP Device Nomenclature (Including the C6414T, C6415T, and C6416T Devices)
64
Added M commercial temperature range information
power-supply sequencing:
72
Updated/changed the paragraph
absolute maximum ratings over operating case temperature range table,

recommended operating conditions table
76
Added M commercial temperature range information

GLZ, ZLZ and CLZ BGA packages (bottom view)

GLZ, ZLZ and CLZ 532-PIN BALL GRID ARRAY (BGA) PACKAGES
( BOTTOM VIEW )
AF
AE
AD
AC
AB
AA
Y
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
1 3 5 7 9 11 13 15 17 19 21 23 25
2 4 6 8 10 12 14 16 18 20 22 24 26

description
The TMS320C64x DSPs (including the TMS320C6414T, TMS320C6415T, and TMS320C6416T devices†)
are the highest-performance fixed-point DSP generation in the TMS320C6000 DSP platform. The
TMS320C64x (C64x) device is based on the second-generation high-performance, advanced VelociTI
very-long-instruction-word (VLIW) architecture (VelociTI.2) developed by Texas Instruments (TI), making
these DSPs an excellent choice for wireless infrastructure applications. The C64x is a code-compatible
member of the C6000 DSP platform.
With performance of up to 8000 million instructions per second (MIPS) at a clock rate of 1 GHz, the C64x devices
offer cost-effective solutions to high-performance DSP programming challenges. The C64x DSPs possess the
operational flexibility of high-speed controllers and the numerical capability of array processors. The C64x
DSP core processor has 64 general-purpose registers of 32-bit word length and eight highly independent
functional units—two multipliers for a 32-bit result and six arithmetic logic units (ALUs)— with VelociTI.2
extensions. The VelociTI.2 extensions in the eight functional units include new instructions to accelerate the
performance in key applications and extend the parallelism of the VelociTI architecture. The C64x can produce
four 16-bit multiply-accumulates (MACs) per cycle for a total of 4000 million MACs per second (MMACS), or
eight 8-bit MACs per cycle for a total of 8000 MMACS. The C64x DSP also has application-specific hardware
logic, on-chip memory, and additional on-chip peripherals similar to the other C6000 DSP platform devices.
The C6416T device has two high-performance embedded coprocessors [Viterbi Decoder Coprocessor (VCP)
and Turbo Decoder Coprocessor (TCP)] that significantly speed up channel-decoding operations on-chip. The
VCP operating at CPU clock divided-by-4 can decode over 833 7.95-Kbps adaptive multi-rate (AMR) [K = 9,
R = 1/3] voice channels. The VCP supports constraint lengths K = 5, 6, 7, 8, and 9, rates R = 1/2, 1/3, and 1/4,
and flexible polynomials, while generating hard decisions or soft decisions. The TCP operating at CPU clock
divided-by-2 can decode up to sixty 384-Kbps or ten 2-Mbps turbo encoded channels (assuming 6 iterations).
The TCP implements the max*log-map algorithm and is designed to support all polynomials and rates required
by Third-Generation Partnership Projects (3GPP and 3GPP2), with fully programmable frame length and turbo
interleaver. Decoding parameters such as the number of iterations and stopping criteria are also programmable.
Communications between the VCP/TCP and the CPU are carried out through the EDMA controller.
The C64x uses a two-level cache-based architecture and has a powerful and diverse set of peripherals. The
Level 1 program cache (L1P) is a 128-Kbit direct mapped cache and the Level 1 data cache (L1D) is a 128-Kbit
2-way set-associative cache. The Level 2 memory/cache (L2) consists of an 8-Mbit memory space that is
shared between program and data space. L2 memory can be configured as mapped memory or combinations
of cache (up to 256K bytes) and mapped memory. The peripheral set includes three multichannel buffered serial
ports (McBSPs); an 8-bit Universal Test and Operations PHY Interface for Asynchronous Transfer Mode (ATM)
Slave [UTOPIA Slave] port [C6415T/C6416T only]; three 32-bit general-purpose timers; a user-configurable
16-bit or 32-bit host-port interface (HPI16/HPI32); a peripheral component interconnect (PCI) [C6415T/C6416T
only]; a general-purpose input/output port (GPIO) with 16 GPIO pins; and two glueless external memory
interfaces (64-bit EMIFA and 16-bit EMIFB‡), both of which are capable of interfacing to synchronous and
asynchronous memories and peripherals.
The C64x has a complete set of development tools which includes: an advanced C compiler with C64x-specific
enhancements, an assembly optimizer to simplify programming and scheduling, and a Windows debugger
interface for visibility into source code execution.
TMS320C6000, C64x, and C6000 are trademarks of Texas Instruments.

Windows is a registered trademark of the Microsoft Corporation.
Other trademarks are the property of their respective owners.
† Throughout the remainder of this document, the TMS320C6414T, TMS320C6415T, and TMS320C6416T shall be referred to as TMS320C64x
or C64x where generic, and where specific, their individual full device part numbers will be used or abbreviated as C6414T, C6415T, or C6416T.
‡ These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). The prefix “A” in front of a signal name indicates it is an EMIFA signal
whereas a prefix “B” in front of a signal name indicates it is an EMIFB signal. Throughout the rest of this document, in generic EMIF areas of
discussion, the prefix “A” or “B” may be omitted from the signal name.

device characteristics
Table 1 provides an overview of the C6414T, C6415T, C6416T DSPs. The table shows significant features of
the C64x devices, including the capacity of on-chip RAM, the peripherals, the CPU frequency, and the package
type with pin count.
Table 1. Characteristics of the C6414T, C6415T, C6416T Processors
HARDWARE FEATURES C6414T, C6415T, and C6416T
EMIFA (64-bit bus width)
1
(default clock source = AECLKIN)
EMIFB (16-bit bus width)
1
Peripherals (default clock source = BECLKIN)
EDMA (64 independent channels) 1
Not all peripherals pins
are available at the same HPI (32- or 16-bit user selectable) 1 (HPI16 or HPI32)
time. (For more details, PCI (32-bit) [DeviceID Register Value 0xA16] 1 [C6415T/C6416T only]
see the Device McBSPs
Configuration section.) (default internal clock source = CPU/4 clock 3
frequency)
Peripheral performance is
dependent on chip-level UTOPIA (8-bit mode) 1 [C6415T/C6416T only]
configuration. 32-Bit Timers
(default internal clock source = CPU/8 clock 3
frequency)
General-Purpose Input/Output 0 (GP0) 16
VCP 1 [C6416T only]
Decoder Coprocessors
TCP 1 [C6416T only]
Size (Bytes) 1056K
On-Chip Memory 16K-Byte (16KB) L1 Program (L1P) Cache

Organization 16KB L1 Data (L1D) Cache
1024KB Unified Mapped RAM/Cache (L2)
CPU ID + CPU Rev ID Control Status Register (CSR.[31:16]) 0x0C01
Silicon Revision Identification Register DEVICE_REV[20:16] Silicon Revision
Device_ID (DEVICE_REV [20:16]) 10000 or 10001 1.0 (14T/15T/16T)
Address: 0x01B0 0200 10010 2.0 (14T/15T/16T)
Frequency MHz 600, 720, 850, 1000 (1-GHz)
1.67 ns (C6414T/15T/16T - 6 [A-600, 600 MHz])†
1.39 ns (C6414T/15T/16T - 7 [A-720, 720 MHz])†
Cycle Time ns
1.17 ns (C6414T/15T/16T - 8 [A-850, 850 MHz]†
1 ns (C6414T/15T/16T - 1 [1 GHz])
1.1 V (600)
Core (V)
Voltage 1.2 V (-720, -850, -1 G)
I/O (V) 3.3 V
PLL Options CLKIN frequency multiplier Bypass (x1), x6, x12, x20
BGA Package 23 x 23 mm 532-Pin BGA (GLZ, ZLZ and CLZ)
Process Technology µm 0.09 µm
† Note: The extended temperature devices’ (A−600, A−720, and A−850) Electrical Characteristics and AC Timings are the same as those for
commercial temperature devices (e.g., −600, −720, and −850).

device compatibility
The C64x generation of devices has a diverse and powerful set of peripherals. The common peripheral set
and pin-compatibility that the C6414T, C6415T, and C6416T devices offer lead to easier system designs and
faster time to market. Table 2 identifies the peripherals and coprocessors that are available on the C6414T,
C6415T, and C6416T devices.
The C6414T, C6415T, and C6416T devices are pin-for-pin compatible, provided the following conditions are
met:
All devices are using the same peripherals.
The C6414T is pin-for-pin compatible with the C6415T/C6416T when the PCI and UTOPIA peripherals on
the C6415T/C6416T are disabled.
The C6415T is pin-for-pin compatible with the C6416T when they are in the same peripheral selection
mode. [For more information on peripheral selection, see the Device Configurations section of this data
sheet.]
The BEA[9:7] pins are properly pulled up/down.
[For more details on the device-specific BEA[9:7] pin configurations, see the Terminal Functions table of
this data sheet.]
Table 2. Peripherals and Coprocessors Available on the C6414T, C6415T, and C6416T Devices†‡
PERIPHERALS/COPROCESSORS C6414T C6415T C6416T
EMIFA (64-bit bus width) √ √ √
EMIFB (16-bit bus width) √ √ √
EDMA (64 independent channels) √ √ √
HPI (32- or 16-bit user selectable) √ √ √
PCI (32-bit) [Specification v2.2] — √ √
McBSPs (McBSP0, McBSP1, McBSP2) √ √ √
UTOPIA (8-bit mode) [Specification v1.0] — √ √
Timers (32-bit) [TIMER0, TIMER1, TIMER2] √ √ √
GPIOs (GP[15:0]) √ √ √
VCP/TCP Coprocessors — — √
† — denotes peripheral/coprocessor is not available on this device.
‡ Not all peripherals pins are available at the same time. (For more details, see the Device Configuration section.)

functional block and CPU (DSP core) diagram
C64x Digital Signal Processor

VCP†
L1P Cache
TCP† Direct-Mapped
64 16K Bytes Total
SDRAM EMIF A
SBSRAM 16
EMIF B
ZBT SRAM C64x DSP Core
Timer 2 Instruction Fetch Control

FIFO
Registers
Instruction Dispatch
SRAM
Timer 1 Advanced Instruction Packet
Control
ROM/FLASH Logic
Instruction Decode
I/O Devices Timer 0
Data Path A Data Path B
Test
A Register File B Register File
A31−A16 B31−B16 Advanced
McBSP2 A15−A0 B15−B0 In-Circuit
Emulation
.L1 .S1 .M1 .D1 .D2 .M2 .S2 .L2 Interrupt

UTOPIA: UTOPIA‡ Control
Enhanced L2
Up to 400 Mbps
or DMA Memory
Master ATMC
Controller 1024K
(64-channel) Bytes
McBSPs:
Framing Chips: McBSP1‡
H.100, MVIP,
SCSA, T1, E1
AC97 Devices,
L1D Cache
SPI Devices,
2-Way Set-Associative
Codecs
McBSP0 16K Bytes Total
16 GPIO[8:0]
GPIO[15:9]‡
32
HPI‡
or
Boot Configuration
PCI‡ PLL Power-Down
(x1, x6, x12, Logic
and x20)
Interrupt
Selector
† VCP and TCP decoder coprocessors are applicable to the C6416T device only.
‡ For the C6415T and C6416T devices, the UTOPIA peripheral is muxed with McBSP1, and the PCI peripheral is muxed with the HPI
peripheral and the GPIO[15:9] port. For more details on the multiplexed pins of these peripherals, see the Device Configurations section
of this data sheet.

CPU (DSP core) description

The CPU fetches VelociTI advanced very-long instruction words (VLIWs) (256 bits wide) to supply up to eight
32-bit instructions to the eight functional units during every clock cycle. The VelociTI VLIW architecture
features controls by which all eight units do not have to be supplied with instructions if they are not ready to
execute. The first bit of every 32-bit instruction determines if the next instruction belongs to the same execute
packet as the previous instruction, or whether it should be executed in the following clock as a part of the next
execute packet. Fetch packets are always 256 bits wide; however, the execute packets can vary in size. The
variable-length execute packets are a key memory-saving feature, distinguishing the C64x CPUs from other
VLIW architectures. The C64x VelociTI.2 extensions add enhancements to the TMS320C62x DSP
VelociTI architecture. These enhancements include:
Register file enhancements
Data path extensions
Quad 8-bit and dual 16-bit extensions with data flow enhancements
Additional functional unit hardware
Increased orthogonality of the instruction set
Additional instructions that reduce code size and increase register flexibility
The CPU features two sets of functional units. Each set contains four units and a register file. One set contains
functional units .L1, .S1, .M1, and .D1; the other set contains units .D2, .M2, .S2, and .L2. The two register files
each contain 32 32-bit registers for a total of 64 general-purpose registers. In addition to supporting the packed
16-bit and 32-/40-bit fixed-point data types found in the C62x VelociTI VLIW architecture, the C64x register
files also support packed 8-bit data and 64-bit fixed-point data types. The two sets of functional units, along with
two register files, compose sides A and B of the CPU [see the functional block and CPU (DSP core) diagram,
and Figure 1]. The four functional units on each side of the CPU can freely share the 32 registers belonging to
that side. Additionally, each side features a “data cross path”—a single data bus connected to all the registers
on the other side, by which the two sets of functional units can access data from the register files on the opposite
side. The C64x CPU pipelines data-cross-path accesses over multiple clock cycles. This allows the same
register to be used as a data-cross-path operand by multiple functional units in the same execute packet. All
functional units in the C64x CPU can access operands via the data cross path. Register access by functional
units on the same side of the CPU as the register file can service all the units in a single clock cycle. On the C64x
CPU, a delay clock is introduced whenever an instruction attempts to read a register via a data cross path if that
register was updated in the previous clock cycle.
In addition to the C62x DSP fixed-point instructions, the C64x DSP includes a comprehensive collection of
quad 8-bit and dual 16-bit instruction set extensions. These VelociTI.2 extensions allow the C64x CPU to
operate directly on packed data to streamline data flow and increase instruction set efficiency.
Another key feature of the C64x CPU is the load/store architecture, where all instructions operate on registers
(as opposed to data in memory). Two sets of data-addressing units (.D1 and .D2) are responsible for all data
transfers between the register files and the memory. The data address driven by the .D units allows data
addresses generated from one register file to be used to load or store data to or from the other register file. The
C64x .D units can load and store bytes (8 bits), half-words (16 bits), and words (32 bits) with a single instruction.
And with the new data path extensions, the C64x .D unit can load and store doublewords (64 bits) with a single
instruction. Furthermore, the non-aligned load and store instructions allow the .D units to access words and
doublewords on any byte boundary. The C64x CPU supports a variety of indirect addressing modes using either
linear- or circular-addressing with 5- or 15-bit offsets. All instructions are conditional, and most can access any
one of the 64 registers. Some registers, however, are singled out to support specific addressing modes or to
hold the condition for conditional instructions (if the condition is not automatically “true”).
TMS320C62x is a trademark of Texas Instruments.

CPU (DSP core) description (continued)

The two .M functional units perform all multiplication operations. Each of the C64x .M units can perform two
16 × 16-bit multiplies or four 8 × 8-bit multiplies per clock cycle. The .M unit can also perform 16 × 32-bit multiply
operations, dual 16 × 16-bit multiplies with add/subtract operations, and quad 8 × 8-bit multiplies with add
operations. In addition to standard multiplies, the C64x .M units include bit-count, rotate, Galois field multiplies,
and bidirectional variable shift hardware.
The two .S and .L functional units perform a general set of arithmetic, logical, and branch functions with results
available every clock cycle. The arithmetic and logical functions on the C64x CPU include single 32-bit, dual
16-bit, and quad 8-bit operations.
The processing flow begins when a 256-bit-wide instruction fetch packet is fetched from a program memory.
The 32-bit instructions destined for the individual functional units are “linked” together by “1” bits in the least
significant bit (LSB) position of the instructions. The instructions that are “chained” together for simultaneous
execution (up to eight in total) compose an execute packet. A “0” in the LSB of an instruction breaks the chain,
effectively placing the instructions that follow it in the next execute packet. A C64x DSP device enhancement
now allows execute packets to cross fetch-packet boundaries. In the TMS320C62x/TMS320C67x DSP
devices, if an execute packet crosses the fetch-packet boundary (256 bits wide), the assembler places it in the
next fetch packet, while the remainder of the current fetch packet is padded with NOP instructions. In the C64x
DSP device, the execute boundary restrictions have been removed, thereby, eliminating all of the NOPs added
to pad the fetch packet, and thus, decreasing the overall code size. The number of execute packets within a
fetch packet can vary from one to eight. Execute packets are dispatched to their respective functional units at
the rate of one per clock cycle and the next 256-bit fetch packet is not fetched until all the execute packets from
the current fetch packet have been dispatched. After decoding, the instructions simultaneously drive all active
functional units for a maximum execution rate of eight instructions every clock cycle. While most results are
stored in 32-bit registers, they can be subsequently moved to memory as bytes, half-words, words, or
doublewords. All load and store instructions are byte-, half-word-, word-, or doubleword-addressable.
For more details on the C64x CPU functional units enhancements, see the following documents:
The TMS320C6000 CPU and Instruction Set Reference Guide (literature number SPRU189)
TMS320C64x Technical Overview (literature number SPRU395)
For more detailed information on the device compatibility, similarities/differences, and migration from the
TMS320C6414/15/16 devices to the TMS320C6414T/15T/16T devices, see the following document:
Migrating From TMS320C6416/15/14 to TMS320C6416T/15T/14T application report (literature number
SPRA981).

CPU (DSP core) description (continued)

src1
.L1
src2
dst
8
long dst
8
long src
32 MSBs
ST1b (Store Data)
32 LSBs
ST1a (Store Data)
8
long src 8
long dst Register
dst File A
.S1 src1 (A0−A31)
Data Path A src2
long dst See Note A

dst See Note A
.M1 src1
src2
LD1b (Load Data) 32 MSBs
LD1a (Load Data) 32 LSBs
dst
DA1 (Address) src1
.D1
src2
2X
1X
src2
.D2
DA2 (Address) src1
dst
LD2a (Load Data) 32 LSBs
LD2b (Load Data) 32 MSBs
src2
.M2 src1
dst See Note A
long dst See Note A
src2 Register
Data Path B File B
.S2
src1 (B0− B31)
dst
8
long dst
long src 8
32 MSBs
ST2a (Store Data)
ST2b (Store Data) 32 LSBs
long src 8
long dst 8
dst
.L2 src2
src1
Control Register
File
NOTE A: For the .M functional units, the long dst is 32 MSBs and the dst is 32 LSBs.
Figure 1. TMS320C64x CPU (DSP Core) Data Paths

memory map summary

Table 3 shows the memory map address ranges of the TMS320C64x device. Internal memory is always located
at address 0 and can be used as both program and data memory. The external memory address ranges in the
C64x device begin at the hex address locations 0x6000 0000 for EMIFB and 0x8000 0000 for EMIFA.

Table 3. TMS320C6414T, C6415T, C6416T Memory Map Summary
MEMORY BLOCK DESCRIPTION BLOCK SIZE (BYTES) HEX ADDRESS RANGE

Internal RAM (L2) 1M 0000 0000 – 000F FFFF
Reserved 23M 0010 0000 – 017F FFFF
External Memory Interface A (EMIFA) Registers 256K 0180 0000 – 0183 FFFF
L2 Registers 256K 0184 0000 – 0187 FFFF
HPI Registers 256K 0188 0000 – 018B FFFF
McBSP 0 Registers 256K 018C 0000 – 018F FFFF
McBSP 1 Registers 256K 0190 0000 – 0193 FFFF
Timer 0 Registers 256K 0194 0000 – 0197 FFFF
Timer 1 Registers 256K 0198 0000 – 019B FFFF
Interrupt Selector Registers 256K 019C 0000 – 019F FFFF
EDMA RAM and EDMA Registers 256K 01A0 0000 – 01A3 FFFF
McBSP 2 Registers 256K 01A4 0000 – 01A7 FFFF
EMIFB Registers 256K 01A8 0000 – 01AB FFFF
Timer 2 Registers 256K 01AC 0000 – 01AF FFFF
GPIO Registers 256K 01B0 0000 – 01B3 FFFF
UTOPIA Registers (C6415T and C6416T only)† 256K 01B4 0000 – 01B7 FFFF
TCP/VCP Registers (C6416T only)‡ 256K 01B8 0000 – 01BB FFFF
Reserved 256K 01BC 0000 – 01BF FFFF
PCI Registers (C6415T and C6416T only)† 256K 01C0 0000 – 01C3 FFFF
Reserved 4M – 256K 01C4 0000 – 01FF FFFF
QDMA Registers 52 0200 0000 – 0200 0033
Reserved 736M – 52 0200 0034 – 2FFF FFFF
McBSP 0 Data 64M 3000 0000 – 33FF FFFF
McBSP 1 Data 64M 3400 0000 – 37FF FFFF
McBSP 2 Data 64M 3800 0000 – 3BFF FFFF
UTOPIA Queues (C6415T and C6416T only)† 64M 3C00 0000 – 3FFF FFFF
Reserved 256M 4000 0000 – 4FFF FFFF
TCP/VCP (C6416T only)‡ 256M 5000 0000 – 5FFF FFFF
EMIFB CE0 64M 6000 0000 – 63FF FFFF
EMIFB CE1 64M 6400 0000 – 67FF FFFF
EMIFB CE2 64M 6800 0000 – 6BFF FFFF
EMIFB CE3 64M 6C00 0000 – 6FFF FFFF
Reserved 256M 7000 0000 – 7FFF FFFF
EMIFA CE0 256M 8000 0000 – 8FFF FFFF
EMIFA CE1 256M 9000 0000 – 9FFF FFFF
EMIFA CE2 256M A000 0000 – AFFF FFFF
EMIFA CE3 256M B000 0000 – BFFF FFFF
Reserved 1G C000 0000 – FFFF FFFF
† For the C6414T device, these memory address locations are reserved. The C6414T device does not support the UTOPIA and PCI peripherals.
‡ Only the C6416T device supports the VCP/TCP Coprocessors. For the C6414T and C6415T devices, these memory address locations are
reserved.

L2 architecture expanded
Figure 2 shows the detail of the L2 architecture on the TMS320C6414T, TMS320C6415T, and
TMS320C6416T devices. For more information on the L2MODE bits, see the cache configuration (CCFG)
register bit field descriptions in the TMS320C64x Two-Level Internal Memory Reference Guide (literature
number SPRU610).
L2MODE L2 Memory Block Base Address
000 001 010 011 111
0x0000 0000
768K SRAM
768K-Byte SRAM
896K SRAM
960K SRAM
992K SRAM
ÎÎÎÎÎÎÎÎÎÎ
1024K SRAM (All)
ÎÎÎÎÎÎÎÎÎÎ 0x000C 0000
128K-Byte RAM
256K Cache (4 Way)
0x000E 0000
64K-Byte RAM
128K Cache (4 Way)
0x000F 0000
64K Cache (4 Way)
32K-Byte RAM
32K Cache
0x000F 8000
(4 Way)
32K-Byte RAM
0x000F FFFF
Figure 2. TMS320C6414T/C6415T/C6416T L2 Architecture Memory Configuration

peripheral register descriptions

Table 4 through Table 23 identify the peripheral registers for the C6414T, C6415T, and C6416T devices by their
register names, acronyms, and hex address or hex address range. For more detailed information on the register
contents, bit names and their descriptions, see the specific peripheral reference guide listed in the
TMS320C6000 DSP Peripherals Overview Reference Guide (literature number SPRU190).
Table 4. EMIFA Registers
HEX ADDRESS RANGE ACRONYM REGISTER NAME

0180 0000 GBLCTL EMIFA global control
0180 0004 CECTL1 EMIFA CE1 space control
0180 000C − Reserved
0180 0018 SDCTL EMIFA SDRAM control
0180 001C SDTIM EMIFA SDRAM refresh control
0180 0020 SDEXT EMIFA SDRAM extension
0180 0024 − 0180 003C − Reserved
0180 0040 PDTCTL Peripheral device transfer (PDT) control
0180 0044 CESEC1 EMIFA CE1 space secondary control
0180 004C − Reserved
0180 0058 − 0183 FFFF – Reserved
Table 5. EMIFB Registers

01A8 0000 GBLCTL EMIFB global control
01A8 0004 CECTL1 EMIFB CE1 space control
01A8 000C − Reserved
01A8 0018 SDCTL EMIFB SDRAM control
01A8 001C SDTIM EMIFB SDRAM refresh control
01A8 0020 SDEXT EMIFB SDRAM extension
01A8 0024 − 01A8 003C − Reserved
01A8 0040 PDTCTL Peripheral device transfer (PDT) control
01A8 0044 CESEC1 EMIFB CE1 space secondary control
01A8 004C − Reserved
01A8 0058 − 01AB FFFF – Reserved

peripheral register descriptions (continued)
Table 6. L2 Cache Registers

HEX ADDRESS RANGE ACRONYM REGISTER NAME COMMENTS
0184 0000 CCFG Cache configuration register
0184 0004 − 0184 0FFC − Reserved
0184 1000 EDMAWEIGHT L2 EDMA access control register
0184 1004 − 0184 1FFC − Reserved
0184 2000 L2ALLOC0 L2 allocation register 0
0184 200C L2ALLOC3 L2 allocation register 3
0184 2010 − 0184 3FFC − Reserved
0184 4000 L2WBAR L2 writeback base address register
0184 4004 L2WWC L2 writeback word count register
0184 4010 L2WIBAR L2 writeback invalidate base address register
0184 4014 L2WIWC L2 writeback invalidate word count register
0184 4018 L2IBAR L2 invalidate base address register
0184 401C L2IWC L2 invalidate word count register
0184 4020 L1PIBAR L1P invalidate base address register
0184 4024 L1PIWC L1P invalidate word count register
0184 4030 L1DWIBAR L1D writeback invalidate base address register
0184 4034 L1DWIWC L1D writeback invalidate word count register
0184 4038 − 0184 4044 − Reserved
0184 4048 L1DIBAR L1D invalidate base address register
0184 404C L1DIWC L1D invalidate word count register
0184 4050 − 0184 4FFC − Reserved
0184 5000 L2WB L2 writeback all register
0184 5004 L2WBINV L2 writeback invalidate all register
0184 5008 − 0184 7FFC − Reserved
MAR0 to
0184 8000 − 0184 817C Reserved
MAR95
0184 8180 MAR96 Controls EMIFB CE0 range 6000 0000 − 60FF FFFF
0184 818C MAR99 Controls EMIFB CE0 range 6300 0000 − 63FF FFFF
0184 819C MAR103 Controls EMIFB CE1 range 6700 0000 − 67FF FFFF
0184 81A0 MAR104 Controls EMIFB CE2 range 6800 0000 − 68FF FFFF
0184 81A4 MAR105 Controls EMIFB CE2 range 6900 0000 − 69FF FFFF
0184 81A8 MAR106 Controls EMIFB CE2 range 6A00 0000 − 6AFF FFFF
0184 81AC MAR107 Controls EMIFB CE2 range 6B00 0000 − 6BFF FFFF

Table 6. L2 Cache Registers (Continued)

0184 81B0 MAR108 Controls EMIFB CE3 range 6C00 0000 − 6CFF FFFF
0184 81B4 MAR109 Controls EMIFB CE3 range 6D00 0000 − 6DFF FFFF
0184 81B8 MAR110 Controls EMIFB CE3 range 6E00 0000 − 6EFF FFFF
0184 81BC MAR111 Controls EMIFB CE3 range 6F00 0000 − 6FFF FFFF
MAR112 to
0184 81C0 − 0184 81FC Reserved
MAR127
0184 8200 MAR128 Controls EMIFA CE0 range 8000 0000 − 80FF FFFF
0184 820C MAR131 Controls EMIFA CE0 range 8300 0000 − 83FF FFFF
0184 8228 MAR138 Controls EMIFA CE0 range 8A00 0000 − 8AFF FFFF
0184 822C MAR139 Controls EMIFA CE0 range 8B00 0000 − 8BFF FFFF
0184 8230 MAR140 Controls EMIFA CE0 range 8C00 0000 − 8CFF FFFF
0184 8234 MAR141 Controls EMIFA CE0 range 8D00 0000 − 8DFF FFFF
0184 8238 MAR142 Controls EMIFA CE0 range 8E00 0000 − 8EFF FFFF
0184 823C MAR143 Controls EMIFA CE0 range 8F00 0000 − 8FFF FFFF
0184 8268 MAR154 Controls EMIFA CE1 range 9A00 0000 − 9AFF FFFF
0184 826C MAR155 Controls EMIFA CE1 range 9B00 0000 − 9BFF FFFF
0184 8270 MAR156 Controls EMIFA CE1 range 9C00 0000 − 9CFF FFFF
0184 8274 MAR157 Controls EMIFA CE1 range 9D00 0000 − 9DFF FFFF
0184 8278 MAR158 Controls EMIFA CE1 range 9E00 0000 − 9EFF FFFF
0184 827C MAR159 Controls EMIFA CE1 range 9F00 0000 − 9FFF FFFF
0184 8280 MAR160 Controls EMIFA CE2 range A000 0000 − A0FF FFFF
0184 828C MAR163 Controls EMIFA CE2 range A300 0000 − A3FF FFFF

Table 6. L2 Cache Registers (Continued)

0184 829C MAR167 Controls EMIFA CE2 range A700 0000 − A7FF FFFF
0184 82A0 MAR168 Controls EMIFA CE2 range A800 0000 − A8FF FFFF
0184 82A4 MAR169 Controls EMIFA CE2 range A900 0000 − A9FF FFFF
0184 82A8 MAR170 Controls EMIFA CE2 range AA00 0000 − AAFF FFFF
0184 82AC MAR171 Controls EMIFA CE2 range AB00 0000 − ABFF FFFF
0184 82B0 MAR172 Controls EMIFA CE2 range AC00 0000 − ACFF FFFF
0184 82B4 MAR173 Controls EMIFA CE2 range AD00 0000 − ADFF FFFF
0184 82B8 MAR174 Controls EMIFA CE2 range AE00 0000 − AEFF FFFF
0184 82BC MAR175 Controls EMIFA CE2 range AF00 0000 − AFFF FFFF
0184 82C0 MAR176 Controls EMIFA CE3 range B000 0000 − B0FF FFFF
0184 82CC MAR179 Controls EMIFA CE3 range B300 0000 − B3FF FFFF
0184 82D0 MAR180 Controls EMIFA CE3 range B400 0000 − B4FF FFFF
0184 82DC MAR183 Controls EMIFA CE3 range B700 0000 − B7FF FFFF
0184 82E0 MAR184 Controls EMIFA CE3 range B800 0000 − B8FF FFFF
0184 82E4 MAR185 Controls EMIFA CE3 range B900 0000 − B9FF FFFF
0184 82E8 MAR186 Controls EMIFA CE3 range BA00 0000 − BAFF FFFF
0184 82EC MAR187 Controls EMIFA CE3 range BB00 0000 − BBFF FFFF
0184 82F0 MAR188 Controls EMIFA CE3 range BC00 0000 − BCFF FFFF
0184 82F4 MAR189 Controls EMIFA CE3 range BD00 0000 − BDFF FFFF
0184 82F8 MAR190 Controls EMIFA CE3 range BE00 0000 − BEFF FFFF
0184 82FC MAR191 Controls EMIFA CE3 range BF00 0000 − BFFF FFFF
MAR192 to
0184 8300 − 0184 83FC Reserved
MAR255
0184 8400 − 0187 FFFF − Reserved

Table 7. EDMA Registers

01A0 FF9C EPRH Event polarity high register
01A0 FFA4 CIPRH Channel interrupt pending high register
01A0 FFA8 CIERH Channel interrupt enable high register
01A0 FFAC CCERH Channel chain enable high register
01A0 FFB0 ERH Event high register
01A0 FFB4 EERH Event enable high register
01A0 FFB8 ECRH Event clear high register
01A0 FFBC ESRH Event set high register
01A0 FFC0 PQAR0 Priority queue allocation register 0
01A0 FFCC PQAR3 Priority queue allocation register 3
01A0 FFDC EPRL Event polarity low register
01A0 FFE0 PQSR Priority queue status register
01A0 FFE4 CIPRL Channel interrupt pending low register
01A0 FFE8 CIERL Channel interrupt enable low register
01A0 FFEC CCERL Channel chain enable low register
01A0 FFF0 ERL Event low register
01A0 FFF4 EERL Event enable low register
01A0 FFF8 ECRL Event clear low register
01A0 FFFC ESRL Event set low register
01A1 0000 − 01A3 FFFF – Reserved

Table 8. EDMA Parameter RAM†

01A0 0000 − 01A0 0017 − Parameters for Event 0 (6 words)
01A0 0018 − 01A0 002F − Parameters for Event 1 (6 words)
01A0 0090 − 01A0 00A7 − Parameters for Event 6 (6 words)
01A0 00A8 − 01A0 00BF − Parameters for Event 7 (6 words)
01A0 00C0 − 01A0 00D7 − Parameters for Event 8 (6 words)
01A0 00D8 − 01A0 00EF − Parameters for Event 9 (6 words)
01A0 00F0 − 01A0 00107 − Parameters for Event 10 (6 words)
... ...
... ...
01A0 05D0 − 01A0 05E7 − Parameters for Event 62 (6 words)
01A0 05E8 − 01A0 05FF − Parameters for Event 63 (6 words)
01A0 0600 − 01A0 0617 − Reload/link parameters for Event M (6 words)
01A0 0618 − 01A0 062F − Reload/link parameters for Event N (6 words)
... ...
01A0 07E0 − 01A0 07F7 − Reload/link parameters for Event Z (6 words)
01A0 07F8 − 01A0 07FF − Scratch pad area (2 words)
† The C6414T/C6415T/C6416T device has twenty-one parameter sets [six (6) words each] that can be used to reload/link EDMA transfers.
Table 9. Quick DMA (QDMA) and Pseudo Registers

0200 0000 QOPT QDMA options parameter register
0200 0004 QSRC QDMA source address register
0200 0008 QCNT QDMA frame count register
0200 000C QDST QDMA destination address register
0200 0010 QIDX QDMA index register
0200 0014 − 0200 001C Reserved
0200 0020 QSOPT QDMA pseudo options register
0200 0024 QSSRC QDMA pseudo source address register
0200 0028 QSCNT QDMA pseudo frame count register
0200 002C QSDST QDMA pseudo destination address register
0200 0030 QSIDX QDMA pseudo index register

Table 10. Interrupt Selector Registers

Selects which interrupts drive CPU
019C 0000 MUXH Interrupt multiplexer high
interrupts 10−15 (INT10−INT15)
Selects which interrupts drive CPU
019C 0004 MUXL Interrupt multiplexer low
interrupts 4−9 (INT04−INT09)
Sets the polarity of the external
019C 0008 EXTPOL External interrupt polarity
interrupts (EXT_INT4−EXT_INT7)
019C 000C − 019C 01FF − Reserved
Table 11. McBSP 0 Registers

The CPU and EDMA controller
018C 0000 DRR0 McBSP0 data receive register via Configuration Bus can only read this register;
they cannot write to it.
0x3000 0000 − 0x33FF FFFF DRR0 McBSP0 data receive register via Peripheral Bus
018C 0004 DXR0 McBSP0 data transmit register via Configuration Bus
0x3000 0000 − 0x33FF FFFF DXR0 McBSP0 data transmit register via Peripheral Bus
018C 0008 SPCR0 McBSP0 serial port control register
018C 000C RCR0 McBSP0 receive control register
018C 0010 XCR0 McBSP0 transmit control register
018C 0014 SRGR0 McBSP0 sample rate generator register
018C 0018 MCR0 McBSP0 multichannel control register
018C 001C RCERE00 McBSP0 enhanced receive channel enable register 0
018C 0020 XCERE00 McBSP0 enhanced transmit channel enable register 0
018C 0024 PCR0 McBSP0 pin control register
018C 0028 RCERE10 McBSP0 enhanced receive channel enable register 1
018C 002C XCERE10 McBSP0 enhanced transmit channel enable register 1
018C 0034 XCERE20 McBSP0 enhanced transmit channel enable register 2
018C 003C XCERE30 McBSP0 enhanced transmit channel enable register 3
018C 0040 − 018F FFFF – Reserved



0190 0000 DRR1 McBSP1 data receive register via Configuration Bus can only read this register;
0x3400 0000 − 0x37FF FFFF DRR1 McBSP1 data receive register via Peripheral Bus
0190 0004 DXR1 McBSP1 data transmit register via Configuration Bus
0x3400 0000 − 0x37FF FFFF DXR1 McBSP1 data transmit register via Peripheral Bus
0190 0008 SPCR1 McBSP1 serial port control register
0190 000C RCR1 McBSP1 receive control register
0190 0010 XCR1 McBSP1 transmit control register
0190 0014 SRGR1 McBSP1 sample rate generator register
0190 0018 MCR1 McBSP1 multichannel control register
0190 001C RCERE01 McBSP1 enhanced receive channel enable register 0
0190 0020 XCERE01 McBSP1 enhanced transmit channel enable register 0
0190 0024 PCR1 McBSP1 pin control register
0190 0028 RCERE11 McBSP1 enhanced receive channel enable register 1
0190 002C XCERE11 McBSP1 enhanced transmit channel enable register 1
0190 0034 XCERE21 McBSP1 enhanced transmit channel enable register 2
0190 003C XCERE31 McBSP1 enhanced transmit channel enable register 3
0190 0040 − 0193 FFFF – Reserved

01A4 0000 DRR2 McBSP2 data receive register via Configuration Bus can only read this register;
0x3800 0000 − 0x3BFF FFFF DRR2 McBSP2 data receive register via Peripheral Bus
01A4 0004 DXR2 McBSP2 data transmit register via Configuration Bus
0x3800 0000 − 0x3BFF FFFF DXR2 McBSP2 data transmit register via Peripheral Bus
01A4 0008 SPCR2 McBSP2 serial port control register
01A4 000C RCR2 McBSP2 receive control register
01A4 0010 XCR2 McBSP2 transmit control register
01A4 0014 SRGR2 McBSP2 sample rate generator register
01A4 0018 MCR2 McBSP2 multichannel control register
01A4 001C RCERE02 McBSP2 enhanced receive channel enable register 0
01A4 0020 XCERE02 McBSP2 enhanced transmit channel enable register 0
01A4 0024 PCR2 McBSP2 pin control register
01A4 0028 RCERE12 McBSP2 enhanced receive channel enable register 1
01A4 002C XCERE12 McBSP2 enhanced transmit channel enable register 1
01A4 0034 XCERE22 McBSP2 enhanced transmit channel enable register 2
01A4 003C XCERE32 McBSP2 enhanced transmit channel enable register 3
01A4 0040 − 01A7 FFFF – Reserved

Table 14. Timer 0 Registers

Determines the operating
mode of the timer, monitors the
0194 0000 CTL0 Timer 0 control register
timer status, and controls the
function of the TOUT pin.
Contains the number of timer
input clock cycles to count.
0194 0004 PRD0 Timer 0 period register
This number controls the
TSTAT signal frequency.
Contains the current value of
0194 0008 CNT0 Timer 0 counter register
the incrementing counter.
0194 000C − 0197 FFFF − Reserved

0198 0000 CTL1 Timer 1 control register
0198 0004 PRD1 Timer 1 period register
0198 0008 CNT1 Timer 1 counter register
0198 000C − 019B FFFF − Reserved

01AC 0000 CTL2 Timer 2 control register
01AC 0004 PRD2 Timer 2 period register
01AC 0008 CNT2 Timer 2 counter register
01AC 000C − 01AF FFFF − Reserved

Table 17. HPI Registers

− HPID HPI data register Host read/write access only
HPIC has both Host/CPU
0188 0000 HPIC HPI control register
read/write access
HPIA
0188 0004 HPI address register (Write)
(HPIAW)† HPIA has both Host/CPU
HPIA read/write access
0188 0008 HPI address register (Read)
(HPIAR)†
0188 000C − 0189 FFFF − Reserved
018A 0000 TRCTL HPI transfer request control register
018A 0004 − 018B FFFF − Reserved
† Host access to the HPIA register updates both the HPIAW and HPIAR registers. The CPU can access HPIAW and HPIAR independently.
Table 18. GPIO Registers

01B0 0000 GPEN GPIO enable register
01B0 0004 GPDIR GPIO direction register
01B0 0008 GPVAL GPIO value register
01B0 000C − Reserved
01B0 0010 GPDH GPIO delta high register
01B0 0014 GPHM GPIO high mask register
01B0 0018 GPDL GPIO delta low register
01B0 001C GPLM GPIO low mask register
01B0 0020 GPGC GPIO global control register
01B0 0024 GPPOL GPIO interrupt polarity register
01B0 0028 − 01B0 01FF − Reserved
Silicon Revision Identification Register
01B0 0200 DEVICE_REV
(For more details, see the device characteristics listed in Table 1.)
01B0 0204 − 01B3 FFFF − Reserved

Table 19. PCI Peripheral Registers (C6415T and C6416T Only)†

01C0 0000 RSTSRC DSP Reset source/status register
01C0 0004 − Reserved
01C0 0008 PCIIS PCI interrupt source register
01C0 000C PCIIEN PCI interrupt enable register
01C0 0010 DSPMA DSP master address register
01C0 0014 PCIMA PCI master address register
01C0 0018 PCIMC PCI master control register
01C0 001C CDSPA Current DSP address register
01C0 0020 CPCIA Current PCI address register
01C0 0024 CCNT Current byte count register
01C0 0028 − Reserved
01C0 002C − 01C1 FFEF – Reserved
0x01C1 FFF0 HSR Host status register
0x01C1 FFF4 HDCR Host-to-DSP control register
0x01C1 FFF8 DSPP DSP page register
0x01C1 FFFC − Reserved
01C2 0000 EEADD EEPROM address register
01C2 0004 EEDAT EEPROM data register
01C2 0008 EECTL EEPROM control register
01C2 000C − 01C2 FFFF – Reserved
01C3 0000 TRCTL PCI transfer request control register
01C3 0004 − 01C3 FFFF – Reserved
† These PCI registers are not supported on the C6414T device.

Table 20. UTOPIA (C6415T and C6416T Only)†

01B4 0000 UCR UTOPIA control register
01B4 0004 − Reserved
01B4 0008 − Reserved
01B4 000C UIER UTOPIA interrupt enable register
01B4 0010 UIPR UTOPIA interrupt pending register
01B4 0014 CDR Clock detect register
01B4 0018 EIER Error interrupt enable register
01B4 001C EIPR Error interrupt pending register
01B4 0020 − 01B7 FFFF − Reserved
† These UTOPIA registers are not supported on the C6414T device.
Table 21. UTOPIA QUEUES (C6415T and C6416T Only)†

3C00 0000 URQ UTOPIA receive queue
3D00 0000 UXQ UTOPIA transmit queue
3D00 0004 − 3FFF FFFF − Reserved
† These UTOPIA registers are not supported on the C6414T device.


Table 22. VCP Registers (C6416T Only)†
EDMA BUS PERIPHERAL BUS

ACRONYM REGISTER NAME
HEX ADDRESS RANGE HEX ADDRESS RANGE
5000 0000 01B8 0000 VCPIC0 VCP input configuration register 0
5000 000C 01B8 000C VCPIC3 VCP input configuration register 3
5000 0040 01B8 0024 VCPOUT0 VCP output register 0

5000 0044 01B8 0028 VCPOUT1 VCP output register 1
5000 0080 − VCPWBM VCP branch metrics write register

5000 0088 − VCPRDECS VCP decisions read register
− 01B8 0018 VCPEXE VCP execution register
− 01B8 0020 VCPEND VCP endian register
− 01B8 0040 VCPSTAT0 VCP status register 0
− 01B8 0044 VCPSTAT1 VCP status register 1
− 01B8 0050 VCPERR VCP error register
† These VCP registers are supported on the C6416T device only.
Table 23. TCP Registers (C6416T Only)‡
EDMA BUS PERIPHERAL BUS

ACRONYM REGISTER NAME
HEX ADDRESS RANGE HEX ADDRESS RANGE
5800 0000 01BA 0000 TCPIC0 TCP input configuration register 0
5800 000C 01BA 000C TCPIC3 TCP input configuration register 3
5800 0030 01BA 0030 TCPOUT TCP output parameters register
5802 0000 − TCPSP TCP systematics and parities memory
5804 0000 − TCPEXT TCP extrinsics memory
5806 0000 − TCPAP TCP apriori memory
5808 0000 − TCPINTER TCP interleaver memory
580A 0000 − TCPHD TCP hard decisions memory
− 01BA 0038 TCPEXE TCP execution register
− 01BA 0040 TCPEND TCP endian register
− 01BA 0050 TCPERR TCP error register
− 01BA 0058 TCPSTAT TCP status register
‡ These TCP registers are supported on the C6416T device only.

EDMA channel synchronization events

The C64x EDMA supports up to 64 EDMA channels which service peripheral devices and external memory.
Table 24 lists the source of C64x EDMA synchronization events associated with each of the programmable
EDMA channels. For the C64x device, the association of an event to a channel is fixed; each of the EDMA
channels has one specific event associated with it. These specific events are captured in the EDMA event
registers (ERL, ERH) even if the events are disabled by the EDMA event enable registers (EERL, EERH). The
priority of each event can be specified independently in the transfer parameters stored in the EDMA parameter
RAM. For more detailed information on the EDMA module and how EDMA events are enabled, captured,
processed, linked, chained, and cleared, etc., see the TMS320C6000 DSP Enhanced Direct Memory Access
(EDMA) Controller Reference Guide (literature number SPRU234).

EDMA channel synchronization events (continued)
Table 24. TMS320C64x EDMA Channel Synchronization Events†

EDMA
EVENT NAME EVENT DESCRIPTION
CHANNEL
0 DSP_INT HPI/PCI-to-DSP interrupt (PCI peripheral supported on C6415T and C6416T only)‡
1 TINT0 Timer 0 interrupt
3 SD_INTA EMIFA SDRAM timer interrupt
4 GPINT4/EXT_INT4 GPIO event 4/External interrupt pin 4
8 GPINT0 GPIO event 0
12 XEVT0 McBSP0 transmit event
13 REVT0 McBSP0 receive event
16 – None
20 SD_INTB EMIFB SDRAM timer interrupt
21 – Reserved, for future expansion
22−27 – None
28 VCPREVT VCP receive event (C6416T only)§
29 VCPXEVT VCP transmit event (C6416T only)§
30 TCPREVT TCP receive event (C6416T only)§
31 TCPXEVT TCP transmit event (C6416T only)§
32 UREVT UTOPIA receive event (C6415T and C6416T only)‡
33−39 – None
40 UXEVT UTOPIA transmit event (C6415T and C6416T only)‡
41−47 – None
56−63 – None
† In addition to the events shown in this table, each of the 64 channels can also be synchronized with the transfer completion or alternate transfer
completion events. For more detailed information on EDMA event-transfer chaining, see the TMS320C6000 DSP Enhanced Direct Memory
Access (EDMA) Controller Reference Guide (literature number SPRU234).
‡ The PCI and UTOPIA peripherals are not supported on the C6414T device; therefore, these EDMA synchronization events are reserved.
§ The VCP/TCP EDMA synchronization events are supported on the C6416T only. For the C6414T and C6415T devices, these events are
reserved.

interrupt sources and interrupt selector

The C64x DSP core supports 16 prioritized interrupts, which are listed in Table 25. The highest-priority interrupt
is INT_00 (dedicated to RESET) while the lowest-priority interrupt is INT_15. The first four interrupts
(INT_00−INT_03) are non-maskable and fixed. The remaining interrupts (INT_04−INT_15) are maskable and
default to the interrupt source specified in Table 25. The interrupt source for interrupts 4−15 can be programmed
by modifying the selector value (binary value) in the corresponding fields of the Interrupt Selector Control
registers: MUXH (address 0x019C0000) and MUXL (address 0x019C0004).

interrupt sources and interrupt selector (continued)
Table 25. C64x DSP Interrupts

INTERRUPT
CPU SELECTOR
SELECTOR INTERRUPT
INTERRUPT VALUE INTERRUPT SOURCE
CONTROL EVENT
NUMBER (BINARY)
REGISTER
INT_00† − − RESET
INT_01† − − NMI
INT_02† − − Reserved Reserved. Do not use.
INT_03† − − Reserved Reserved. Do not use.
INT_04‡ MUXL[4:0] 00100 GPINT4/EXT_INT4 GPIO interrupt 4/External interrupt pin 4
INT_08‡ MUXL[25:21] 01000 EDMA_INT EDMA channel (0 through 63) interrupt
INT_09‡ MUXL[30:26] 01001 EMU_DTDMA EMU DTDMA
INT_10‡ MUXH[4:0] 00011 SD_INTA EMIFA SDRAM timer interrupt
EMU real-time data exchange (RTDX)
INT_11‡ MUXH[9:5] 01010 EMU_RTDXRX
receive
INT_12‡ MUXH[14:10] 01011 EMU_RTDXTX EMU RTDX transmit
HPI/PCI-to-DSP interrupt
INT_13‡ MUXH[20:16] 00000 DSP_INT
(PCI supported on C6415T and C6416T)
INT_14‡ MUXH[25:21] 00001 TINT0 Timer 0 interrupt
INT_15‡ MUXH[30:26] 00010 TINT1 Timer 1 interrupt
− − 01100 XINT0 McBSP0 transmit interrupt
− − 01101 RINT0 McBSP0 receive interrupt
− − 10000 GPINT0 GPIO interrupt 0
− − 10011 TINT2 Timer 2 interrupt
− − 10100 SD_INTB EMIFB SDRAM timer interrupt
− − 10101 Reserved Reserved. Do not use.
− − 10110 Reserved Reserved. Do not use.
− − 10111 UINT UTOPIA interrupt (C6415T/C6416T only)
− − 11000 − 11101 Reserved Reserved. Do not use.
− − 11110 VCPINT VCP interrupt (C6416T only)
− − 11111 TCPINT TCP interrupt (C6416T only)
† Interrupts INT_00 through INT_03 are non-maskable and fixed.

‡ Interrupts INT_04 through INT_15 are programmable by modifying the binary selector values in the Interrupt Selector Control
registers fields. Table 25 shows the default interrupt sources for Interrupts INT_04 through INT_15. For more detailed
information on interrupt sources and selection, see the TMS320C6000 DSP Interrupt Selector Reference Guide (literature
number SPRU646).

signal groups description
RESET
CLKIN NMI
CLKOUT4/GP1† Reset and GP7/EXT_INT7‡
CLKOUT6/GP2† Clock/PLL Interrupts GP6/EXT_INT6‡
CLKMODE1 GP5/EXT_INT5‡
CLKMODE0 GP4/EXT_INT4‡
PLLV
RSV
RSV
TMS RSV
TDO RSV
TDI RSV
TCK RSV
Reserved
TRST •
EMU0 •
EMU1 IEEE Standard •
EMU2 1149.1 RSV
EMU3 (JTAG) RSV
EMU4 Emulation RSV
EMU5
EMU6
EMU7
EMU8
EMU9 Peripheral PCI_EN
EMU10 Control/Status MCBSP2_EN
EMU11
Control/Status
GP15/PRST§ GP7/EXT_INT7‡
GP14/PCLK§ GP6/EXT_INT6‡
GP13/PINTA§ GP5/EXT_INT5‡
GP12/PGNT§ GP4/EXT_INT4‡
GPIO
GP11/PREQ§ GP3
GP10/PCBE3§ CLKOUT6/GP2†
GP9/PIDSEL§ CLKOUT4/GP1†
CLKS2/GP8† GP0
General-Purpose Input/Output (GPIO) Port
† These pins are muxed with the GPIO port pins and by default these signals function as clocks (CLKOUT4 or CLKOUT6) or McBSP2
clock source (CLKS2). To use these muxed pins as GPIO signals, the appropriate GPIO register bits (GPxEN and GPxDIR) must be
properly enabled and configured. For more details, see the Device Configurations section of this data sheet.
‡ These pins are GPIO pins that can also function as external interrupt sources (EXT_INT[7:4]). Default after reset is EXT_INTx or
GPIO as input-only.
§ For the C6415T and C6416T devices, these GPIO pins are muxed with the PCI peripheral pins. By default, these signals are set up
to no function with both the GPIO and PCI pin functions disabled. For more details on these muxed pins, see the Device
Configurations section of this data sheet. For the C6414T device, the GPIO peripheral pins are not muxed; the C6414T device does
not support the PCI peripheral.
Figure 3. CPU and Peripheral Signals

signal groups description (continued)
64
AED[63:0] Data AECLKIN
AECLKOUT1
ACE3 AECLKOUT2
ACE2 Memory Map ASDCKE
External
ACE1 Space Select AARE/ASDCAS/ASADS/ASRE
Memory I/F
ACE0 Control AAOE/ASDRAS/ASOE
20 AAWE/ASDWE/ASWE
AEA[22:3] Address AARDY
ASOE3
ABE7 APDT
ABE6
ABE5
ABE4 Byte Enables AHOLD
Bus
ABE3 Arbitration AHOLDA
ABE2 ABUSREQ
ABE1
ABE0
EMIFA (64-bit)†
16
BED[15:0] Data
BECLKIN
BECLKOUT1
BECLKOUT2
BCE3
External BARE/BSDCAS/BSADS/BSRE
BCE2 Memory Map
Memory I/F BAOE/BSDRAS/BSOE
BCE1 Space Select
Control
BCE0 BAWE/BSDWE/BSWE
BARDY
20
BEA[20:1] Address BSOE3
BPDT
BBE1 Byte Enables

BBE0 Bus BHOLD
Arbitration BHOLDA
EMIFB (16-bit)† BBUSREQ
† These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). The prefix “A” in front of a signal name indicates it is
an EMIFA signal whereas a prefix “B” in front of a signal name indicates it is an EMIFB signal. Throughout the rest of this document,
in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted from the signal name.
Figure 4. Peripheral Signals

HPI†
32 (Host-Port Interface)
HD[31:0]/AD[31:0] Data
HAS/PPAR
HCNTL0/PSTOP HR/W/PCBE2
Register Select HCS/PPERR
HCNTL1/PDEVSEL
Control HDS1/PSERR
HDS2/PCBE1
Half-Word HRDY/PIRDY
HHWIL/PTRDY
Select HINT/PFRAME
(HPI16 ONLY)
32
HD[31:0]/AD[31:0] Data/Address Clock GP14/PCLK
GP9/PIDSEL
HCNTL1/PDEVSEL
GP10/PCBE3 HINT/PFRAME
HR/W/PCBE2 Command GP13/PINTA
HDS2/PCBE1 Byte Enable Control HAS/PPAR
PCBE0§ GP15/PRST
HRDY/PIRDY
HCNTL0/PSTOP
HHWIL/PTRDY
GP12/PGNT
Arbitration HDS1/PSERR
GP11/PREQ Error
HCS/PPERR
DX2/XSP_DO
Serial XSP_CS§
EEPROM CLKX2/XSP_CLK
DR2/XSP_DI
PCI Interface‡
(C6415T and C6416T Only
† For the C6415T and C6416T devices, these HPI pins are muxed with the PCI peripheral. By default, these signals function as HPI. For
more details on these muxed pins, see the Device Configurations section of this data sheet. For the C6414 device, these HPI pins are
not muxed; the C6414T device does not support the PCI peripheral.
‡ For the C6415T and C6416T devices, these PCI pins (excluding PCBE0 and XSP_CS) are muxed with the HPI, McBSP2, or GPIO
peripherals. By default, these signals function as HPI, McBSP2, and no function, respectively. For more details on these muxed pins,
see the Device Configurations section of this data sheet. For the C6414T device, the HPI, McBSP2, and GPIO peripheral pins are not
muxed; the C6414T device does not support the PCI peripheral.
§ For the C6414T device, these pins are “Reserved (leave unconnected, do not connect to power or ground).”
Figure 4. Peripheral Signals (Continued)

McBSP1 McBSP0
CLKX1/URADDR4† CLKX0
FSX1/UXADDR3† Transmit Transmit FSX0
DX1/UXADDR4† DX0
CLKR1/URADDR2† CLKR0
FSR1/UXADDR2† Receive Receive FSR0
DR1/UXADDR1† DR0
CLKS1/URADDR3† Clock Clock CLKS0
McBSP2
CLKX2/XSP_CLK†
FSX2 Transmit
DX2/XSP_DO†
CLKR2
FSR2 Receive
DR2/XSP_DI†
McBSPs
CLKS2/GP8‡ Clock
(Multichannel Buffered
Serial Ports)
† For the C6415T and C6416T devices, these McBSP2 and McBSP1 pins are muxed with the PCI and UTOPIA peripherals, respectively.
By default, these signals function as McBSP2 and McBSP1, respectively. For more details on these muxed pins, see the Device
Configurations section of this data sheet.
For the C6414T device, these McBSP2 and McBSP1 peripheral pins are not muxed; the C6414T device does not support PCI and
UTOPIA peripherals.
‡ The McBSP2 clock source pin (CLKS2, default) is muxed with the GP8 pin. To use this muxed pin as the GP8 signal, the appropriate
GPIO register bits (GP8EN and GP8DIR) must be properly enabled and configured. For more details, see the Device Configurations
section of this data sheet.

UTOPIA (SLAVE) [C6415T and C6416T Only]
URDATA7 UXDATA7
URDATA6 UXDATA6
URDATA5 UXDATA5
URDATA4 UXDATA4
Receive Transmit
URDATA3 UXDATA3
URDATA2 UXDATA2
URDATA1 UXDATA1
URDATA0 UXDATA0
URENB UXENB
CLKX1/URADDR4† DX1/UXADDR4†
CLKS1/URADDR3† FSX1/UXADDR3†
CLKR1/URADDR2† FSR1/UXADDR2†
Control/Status Control/Status
URADDR1 DR1/UXADDR1†
URADDR0 UXADDR0
URCLAV UXCLAV
URSOC UXSOC
URCLK Clock Clock UXCLK
TOUT1 TOUT0
Timer 1 Timer 0
TINP1 TINP0
TOUT2
Timer 2
TINP2 Timers
† For the C6415T and C6416T devices, these UTOPIA pins are muxed with the McBSP1 peripheral. By default, these signals function
as McBSP1. For more details on these muxed pins, see the Device Configurations section of this data sheet.
For the C6414T device, these McBSP1 peripheral pins are not muxed; the C6414T does not support the UTOPIA peripheral.

DEVICE CONFIGURATIONS
The C6414T, C6415T, and C6416T device configurations are determined by external pullup/pulldown resistors
on the following pins (all of which are latched during device reset):
peripherals selection (C6415T and C6416T devices)
− BEA11 (UTOPIA_EN)
− PCI_EN (for C6415T or C6416T, see Table 27 footnotes)
− MCBSP2_EN (for C6415T or C6416T, see Table 27 footnotes)
The C6414T device does not support the PCI and UTOPIA peripherals; for proper operation of the C6414T
device, do not oppose the internal pulldowns (IPDs) on the BEA11, PCI_EN, and MCBSP2_EN pins. (For
IPUs/IPDs on pins, see the Terminal Functions table of this data sheet.)
other device configurations (C64x)
− BEA[20:13, 7]
− HD5
peripherals selection
Some C6415T/C6416T peripherals share the same pins (internally muxed) and are mutually exclusive (i.e.,
HPI, general-purpose input/output pins GP[15:9], PCI and its internal EEPROM, McBSP1, McBSP2, and
UTOPIA). The VCP/TCP coprocessors (C6416T only) and other C64x peripherals (i.e., the Timers, McBSP0,
and the GP[8:0] pins), are always available.
UTOPIA and McBSP1 peripherals
The UTOPIA_EN pin (BEA11) is latched at reset. For C6415T and C6416T devices, this pin selects whether
the UTOPIA peripheral or McBSP1 peripheral is functionally enabled (see Table 26).
The C6414T device does not support the UTOPIA peripheral; for proper device operation, do not oppose
the internal pulldown (IPD) on the BEA11 pin.
Table 26. UTOPIA_EN Peripheral Selection (McBSP1 and UTOPIA) (C6415T/C6416T Only)
PERIPHERAL SELECTION PERIPHERALS SELECTED
UTOPIA_EN DESCRIPTION
UTOPIA McBSP1
(BEA11) Pin [D16]
McBSP1 is enabled and UTOPIA is disabled [default].
0 √ This means all multiplexed McBSP1/UTOPIA pins function as McBSP1
and all other standalone UTOPIA pins are tied-off (Hi-Z).
UTOPIA is enabled and McBSP1 is disabled.
1 √ This means all multiplexed McBSP1/UTOPIA pins now function as
UTOPIA and all other standalone McBSP1 pins are tied-off (Hi-Z).
HPI, GP[15:9], PCI, EEPROM (internal to PCI), and McBSP2 peripherals

The PCI_EN and MCBSP2_EN pins are latched at reset. They determine specific peripheral selection for
the C6415T and C6416T devices, summarized in Table 27.
The C6414T device does not support the PCI peripheral; for proper device operation, do not oppose the
internal pulldowns (IPDs) on the PCI_EN and MCBSP2_EN pins.

DEVICE CONFIGURATIONS (CONTINUED)
Table 27. PCI_EN and MCBSP2_EN Peripheral Selection (HPI, GP[15:9], PCI, and McBSP2)
PERIPHERAL SELECTION† PERIPHERALS SELECTED
PCI_EN MCBSP2_EN EEPROM
HPI GP[15:9] PCI McBSP2
Pin [AA4] Pin [AF3] (Internal to PCI)
0 0 √ √ √
0 1 √ √ √
1 0 √ √ ‡
1 1 √ √
† The PCI_EN pin must be driven valid at all times and the user must not switch values throughout device operation.
The MCBSP2_EN pin must be driven valid at all times and the user can switch values throughout device operation.
‡ The only time McBSP2 is disabled is when both PCI_EN = 1 and MCBSP2_EN = 0. This configuration enables, at reset, the auto-initialization
of the PCI peripheral through the PCI internal EEPROM [provided the PCI EEPROM Auto-Initialization pin (BEA13) is pulled up
(EEAI = 1)]. The user can then enable the McBSP2 peripheral (disabling EEPROM) by dynamically changing MCBSP2_EN to a “1” after the
device is initialized (out of reset).
− If the PCI is disabled (PCI_EN = 0), the HPI peripheral is enabled and GP[15:9] pins can be programmed
as GPIO, provided the GPxEN and GPxDIR bits are properly configured. [Note: The PCI_EN pin must
be driven valid at all times and the user must not switch values throughout device operation.]
This means all multiplexed HPI/PCI pins function as HPI and all standalone PCI pins (PCBE0 and
XSP_CS) are tied-off (Hi-Z). Also, the multiplexed GPIO/PCI pins can be used as GPIO with the
proper software configuration of the GPIO enable and direction registers (for more details, see
Table 29).
− If the PCI is enabled (PCI_EN = 1), the HPI peripheral is disabled. [Note: The PCI_EN pin must be driven
valid at all times and the user must not switch values throughout device operation.]
This means all multiplexed HPI/PCI pins function as PCI. Also, the multiplexed GPIO/PCI pins function
as PCI pins (for more details, see Table 29).
− The MCBSP2_EN pin, in combination with the PCI_EN pin, controls the selection of the McBSP2
peripheral and the PCI internal EEPROM (for more details, see Table 27 and its footnotes). [Note: The
MCBSP2_EN pin must be driven valid at all times and the user can switch values throughout device
operation.]
other device configurations

Table 28 describes the C6414T, C6415T, and C6416T devices configuration pins, which are set up via external
pullup/pulldown resistors through the specified EMIFB address bus pins (BEA[20:13, 11, 9:7]) and the HD5 pin.
For more details on these device configuration pins, see the Terminal Functions table and the Debugging
Considerations section.


Table 28. Device Configuration Pins (BEA[20:13, 9:7], HD5, and BEA11)
CONFIGURATION
NO. FUNCTIONAL DESCRIPTION
PIN
Device Endian mode (LEND)
BEA20 E16 0 – System operates in Big Endian mode
1 − System operates in Little Endian mode (default)
Bootmode [1:0]
00 – No boot
[D18,
BEA[19:18] 01 − HPI boot
C18]
10 − EMIFB 8-bit ROM boot with default timings (default mode)
11 − Reserved
EMIFA input clock select
Clock mode select for EMIFA (AECLKIN_SEL[1:0])
[B18, 00 – AECLKIN (default mode)
BEA[17:16]
A18] 01 − CPU/4 Clock Rate
10 − CPU/6 Clock Rate
11 − Reserved
EMIFB input clock select
Clock mode select for EMIFB (BECLKIN_SEL[1:0])
[D17, 00 – BECLKIN (default mode)
BEA[15:14]
C17] 01 − CPU/4 Clock Rate
11 − Reserved
PCI EEPROM Auto-Initialization (EEAI) [C6415T and C6416T devices only]
[The C6414T device does not support the PCI peripheral; for proper device operation, do not oppose
the internal pulldown (IPD) on the BEA13 pin.]
PCI auto-initialization via external EEPROM
0 − PCI auto-initialization through EEPROM is disabled; the PCI peripheral uses the specified
PCI default values (default).
BEA13 B17 1 − PCI auto-initialization through EEPROM is enabled; the PCI peripheral is configured
through EEPROM provided the PCI peripheral pin is enabled (PCI_EN = 1) and the
McBSP2 peripheral pin is disabled (MCBSP2_EN = 0).
Note: If the PCI peripheral is disabled (PCI_EN pin = 0), this pin must not be pulled up.
For more information on the PCI EEPROM default values, see the TMS320C6000 DSP Peripheral
Component Interconnect (PCI) Reference Guide (literature number SPRU581).
UTOPIA Enable (UTOPIA_EN) [C6415T and C6416T devices only]
[The C6414T device does not support the UTOPIA peripheral; for proper device operation, do not
oppose the internal pulldown (IPD) on the BEA11 pin.]
UTOPIA peripheral enable (functional)
0 − UTOPIA peripheral disabled (McBSP1 functions are enabled). [default]

BEA11 D16
This means all multiplexed McBSP1/UTOPIA pins function as McBSP1 and all other
standalone UTOPIA pins are tied-off (Hi-Z).
1 − UTOPIA peripheral enabled (McBSP1 functions are disabled).

This means all multiplexed McBSP1/UTOPIA pins now function as UTOPIA and all other
standalone McBSP1 pins are tied-off (Hi-Z).

Table 28. Device Configuration Pins (BEA[20:13, 9:7], HD5, and BEA11) (Continued)
CONFIGURATION
NO. FUNCTIONAL DESCRIPTION
PIN
C6414T Devices C6415T Devices C6416T Devices
BEA7 D15 Do not oppose internal pulldown (IPD) Pullup† Do not oppose IPD
BEA8 A16 Do not oppose IPD Do not oppose IPD Pullup†
BEA9 B16 Do not oppose IPD Do not oppose IPD Pullup†
†For proper device operation, this pin must be externally pulled up with a 1-kΩ resistor.
HPI peripheral bus width (HPI_WIDTH)

0 − HPI operates as an HPI16.
(HPI bus is 16 bits wide. HD[15:0] pins are used and the remaining HD[31:16] pins are
HD5 Y1
reserved pins in the Hi-Z state.)
1 − HPI operates as an HPI32.
(HPI bus is 32 bits wide. All HD[31:0] pins are used for host-port operations.)
multiplexed pins
Multiplexed pins are pins that are shared by more than one peripheral and are internally multiplexed. Some of
these pins are configured by software, and the others are configured by external pullup/pulldown resistors only
at reset. Those muxed pins that are configured by software can be programmed to switch functionalities at any
time. Those muxed pins that are configured by external pullup/pulldown resistors are mutually exclusive; only
one peripheral has primary control of the function of these pins after reset. Table 29 identifies the multiplexed
pins on the C6414T, C6415T, and C6416T devices; shows the default (primary) function and the default settings
after reset; and describes the pins, registers, etc. necessary to configure specific multiplexed functions.
debugging considerations
It is recommended that external connections be provided to device configuration pins, including
CLKMODE[1:0], BEA[20:13, 11, 9:7], HD5/AD5, PCI_EN, and MCBSP2_EN. Although internal pullup/pulldown
resistors exist on these pins (except for HD5/AD5), providing external connectivity adds convenience to the user
in debugging and flexibility in switching operating modes.
Internal pullup/pulldown resistors also exist on the non-configuration pins on the BEA bus (BEA[12, 10, 6:1]).
Do not oppose the internal pullup/pulldown resistors on these non-configuration pins with external
pullup/pulldown resistors. If an external controller provides signals to these non-configuration pins, these
signals must be driven to the default state of the pins at reset, or not be driven at all.
For the internal pullup/pulldown resistors on the C6414T, C6415T, and C6416T device pins, see the terminal
functions table.

Table 29. C6414T, C6415T, and C6416T Device Multiplexed Pins†

MULTIPLEXED PINS
DEFAULT FUNCTION DEFAULT SETTING DESCRIPTION
NAME NO.
These pins are software-configurable.
CLKOUT4/GP1‡ AE6 CLKOUT4 GP1EN = 0 (disabled) To use these pins as GPIO pins, the
GPxEN bits in the GPIO Enable
Register and the GPxDIR bits in the
CLKOUT6/GP2‡ AD6 CLKOUT6 GP2EN = 0 (disabled) GPIO Direction Register must be
properly configured.
GPxEN = 1: GPx pin enabled
CLKS2/GP8‡ AE4 CLKS2 GP8EN = 0 (disabled) GPxDIR = 0: GPx pin is an input
GPxDIR = 1: GPx pin is an output
GP9/PIDSEL M3 To use GP[15:9] as GPIO pins, the PCI
GP10/PCBE3 L2 needs to be disabled (PCI_EN = 0), the
GPxEN bits in the GPIO Enable
GP11/PREQ F1 Register and the GPxDIR bits in the
GPxEN = 0 (disabled)
GP12/PGNT J3 None GPIO Direction Register must be
PCI_EN = 0 (disabled)†
GP13/PINTA G4 properly configured.
GPxEN = 1: GPx pin enabled
GP14/PCLK F2 GPxDIR = 0: GPx pin is an input
GP15/PRST G3 GPxDIR = 1: GPx pin is an output
DX1/UXADDR4 AB11 DX1
FSX1/UXADDR3 AB13 FSX1 By default, McBSP1 is enabled upon
FSR1/UXADDR2 AC9 FSR1 reset (UTOPIA is disabled).
UTOPIA_EN (BEA11) = 0 To enable the UTOPIA peripheral, an
DR1/UXADDR1 AF11 DR1
(disabled)† external pullup resistor (1 kΩ) must be
CLKX1/URADDR4 AB12 CLKX1 provided on the BEA11 pin (setting
CLKS1/URADDR3 AC8 CLKS1 UTOPIA_EN = 1 at reset).
CLKR1/URADDR2 AC10 CLKR1
CLKX2/XSP_CLK AC2 CLKX2
DR2/XSP_DI AB3 DR2
DX2/XSP_DO AA2 DX2
HD[31:0]/AD[31:0] ‡ HD[31:0]
HAS/PPAR T3 HAS
HCNTL1/PDEVSEL R1 HCNTL1 By default, HPI is enabled upon reset
(PCI is disabled).
HCNTL0/PSTOP T4 HCNTL0 To enable the PCI peripheral an external
PCI_EN = 0 (disabled)†
HDS1/PSERR T1 HDS1 pullup resistor (1 kkΩ)) must be provided
on the PCI_EN pin (setting PCI_EN = 1
HDS2/PCBE1 T2 HDS2
at reset).
HR/W/PCBE2 P1 HR/W
HHWIL/PTRDY R3 HHWIL (HPI16 only)
HINT/PFRAME R4 HINT
HCS/PPERR R2 HCS
HRDY/PIRDY P4 HRDY
† For the C6415T and C6416T devices, all other standalone UTOPIA and PCI pins are tied-off internally (pins in Hi-Z) when the peripheral is
disabled [UTOPIA_EN (BEA11) = 0 or PCI_EN = 0].
‡ The C6414T device does not support the PCI and UTOPIA peripherals. These are the only multiplexed pins on the C6414T device, all other
pins are standalone peripheral functions and are not muxed.
§ For the HD[31:0]/AD[31:0] multiplexed pins pin numbers, see the Terminal Functions table.

Terminal Functions
SIGNAL IPD/
TYPE† DESCRIPTION
NAME NO. IPU‡
CLOCK/PLL CONFIGURATION
CLKIN H4 I IPD Clock Input. This clock is the input to the on-chip PLL.
Clock output at 1/4 of the device speed (O/Z) [default] or this pin can be programmed as a
CLKOUT4/GP1§ AE6 I/O/Z IPD
GPIO 1 pin (I/O/Z).
CLKOUT6/GP2§ AD6 I/O/Z IPD
GPIO 2 pin (I/O/Z).
CLKMODE1 G1 I IPD Clock mode select

• Selects whether the CPU clock frequency = input clock frequency x1 (Bypass), x6, or x12,
or x20. For more details on the CLKMODE pins and the PLL multiply factors, see the Clock
CLKMODE0 H2 I IPD
PLL section of this data sheet.
PLLV¶ J6 A# PLL voltage supply
JTAG EMULATION
TMS AB16 I IPU JTAG test-port mode select
TDO AE19 O/Z IPU JTAG test-port data out
TDI AF18 I IPU JTAG test-port data in
TCK AF16 I IPU JTAG test-port clock
JTAG test-port reset. For IEEE 1149.1 JTAG compatibility, see the IEEE 1149.1 JTAG
TRST AB15 I IPD
Compatibility Statement section of this data sheet.
EMU11 AC18 I/O/Z IPU Emulation pin 11. Reserved for future use, leave unconnected.
EMU10 AD18 I/O/Z IPU Emulation pin 10. Reserved for future use, leave unconnected.
EMU9 AE18 I/O/Z IPU Emulation pin 9. Reserved for future use, leave unconnected.
EMU7 AF17 I/O/Z IPU Emulation pin 7. Reserved for future use, leave unconnected.
Emulation [1:0] pins
• Select the device functional mode of operation
EMU[1:0] Operation
00 Boundary Scan/Normal Mode (see Note)
01 Reserved
10 Reserved
11 Emulation/Normal Mode [default] (see the IEEE 1149.1 JTAG
EMU1 AC15 Compatibility Statement section of this data sheet)
I/O/Z IPU
EMU0 AF15 Normal mode refers to the DSPs normal operational mode, when the DSP is free running. The
DSP can be placed in normal operational mode when the EMU[1:0] pins are configured for
either Boundary Scan or Emulation.
Note: When the EMU[1:0] pins are configured for Boundary Scan mode, the internal pulldown
(IPD) on the TRST signal must not be opposed in order to operate in Normal mode.
For the Boundary Scan mode pulldown EMU[1:0] pins with a dedicated 1-kΩ resistor.
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
‡ IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
§ These pins are multiplexed pins. For more details, see the Device Configurations section of this data sheet.
¶ PLLV is not part of external voltage supply. See the Clock PLL section for information on how to connect this pin.
# A = Analog signal (PLL Filter)

Terminal Functions (Continued)

SIGNAL IPD/
TYPE† DESCRIPTION
NAME NO. IPU‡
RESETS, INTERRUPTS, AND GENERAL-PURPOSE INPUT/OUTPUTS
RESET AC7 I Device reset
Nonmaskable interrupt, edge-driven (rising edge)
NMI B4 I IPD
Any noise on the NMI pin may trigger an NMI interrupt; therefore, if the NMI pin is not used, it
is recommended that the NMI pin be grounded versus relying on the IPD.
GP7/EXT_INT7 AF4 General-purpose input/output (GPIO) pins (I/O/Z) or external interrupts (input only). The
GP6/EXT_INT6 AD5 default after reset setting is GPIO enabled as input-only.
I/O/Z IPU • When these pins function as External Interrupts [by selecting the corresponding interrupt
GP5/EXT_INT5 AE5 enable register bit (IER.[7:4])], they are edge-driven and the polarity can be
GP4/EXT_INT4 AF5 independently selected via the External Interrupt Polarity Register bits (EXTPOL.[3:0]).
GP15/PRST§ G3 General-purpose input/output (GPIO) 15 pin (I/O/Z) or PCI reset (I). No function at default.
GP14/PCLK§ F2 GPIO 14 pin (I/O/Z) or PCI clock (I). No function at default.
GP13/PINTA§ G4 GPIO 13 pin (I/O/Z) or PCI interrupt A (O/Z). No function at default.
GP12/PGNT§ J3 GPIO 12 pin (I/O/Z) or PCI bus grant (I). No function at default.
GP11/PREQ§ F1 GPIO 11 pin (I/O/Z) or PCI bus request (O/Z). No function at default.
GP10/PCBE3§ L2 I/O/Z GPIO 10 pin (I/O/Z) or PCI command/byte enable 3 (I/O/Z). No function at default.
GP9/PIDSEL§ M3 GPIO 9 pin (I/O/Z) or PCI initialization device select (I). No function at default.
GP3 AC6 IPD GPIO 3 pin (I/O/Z). The default after reset setting is GPIO 3 enabled as input-only.
GPIO 0 pin.
The general-purpose I/O 0 pin (GPIO 0) (I/O/Z) can be programmed as GPIO 0 (input only)
GP0 AF6 IPD
[default] or as GPIO 0 (output only) pin or output as a general-purpose interrupt (GP0INT)
signal (output only).
McBSP2 external clock source (CLKS2) [input only] [default] or this pin can be pro-
CLKS2/GP8§¶ AE4 I/O/Z IPD
grammed as a GPIO 8 pin (I/O/Z).
CLKOUT6/GP2§¶ AD6 I/O/Z IPD
GPIO 2 pin (I/O/Z).
CLKOUT4/GP1§¶ AE6 I/O/Z IPD
GPIO 1 pin (I/O/Z).
HOST-PORT INTERFACE (HPI) [C64x] or PERIPHERAL COMPONENT INTERCONNECT (PCI) [C6415T or C6416T devices only]
PCI enable pin. This pin controls the selection (enable/disable) of the HPI and GP[15:9], or
PCI_EN AA4 I IPD PCI peripherals. This pin works in conjunction with the MCBSP2_EN pin to enable/disable
other peripherals (for more details, see the Device Configurations section of this data sheet).
HINT/PFRAME§ R4 I/O/Z Host interrupt from DSP to host (O) [default] or PCI frame (I/O/Z)
HCNTL1/ Host control − selects between control, address, or data registers (I) [default] or PCI device
R1 I/O/Z
PDEVSEL§ select (I/O/Z).
HCNTL0/ Host control − selects between control, address, or data registers (I) [default] or PCI stop
T4 I/O/Z
PSTOP§ (I/O/Z)
Host half-word select − first or second half-word (not necessarily high or low order)
HHWIL/PTRDY§ R3 I/O/Z
[For HPI16 bus width selection only] (I) [default] or PCI target ready (I/O/Z)
HR/W/PCBE2§ P1 I/O/Z Host read or write select (I) [default] or PCI command/byte enable 2 (I/O/Z)
§ For the C6415T and C6416T devices, these pins are multiplexed pins. For more details, see the Device Configurations section of this data sheet.
The C6414T device does not support the PCI or UTOPIA peripherals; therefore, these muxed peripheral pins are standalone peripheral functions
for this device.
¶ For the C6414T device, only these pins are multiplexed pins.


SIGNAL IPD/
TYPE† DESCRIPTION
NAME NO. IPU‡
(CONTINUED)
HAS/PPAR§ T3 I/O/Z Host address strobe (I) [default] or PCI parity (I/O/Z)
HCS/PPERR§ R2 I/O/Z Host chip select (I) [default] or PCI parity error (I/O/Z)
HDS1/PSERR§ T1 I/O/Z Host data strobe 1 (I) [default] or PCI system error (I/O/Z)
HDS2/PCBE1§ T2 I/O/Z Host data strobe 2 (I) [default] or PCI command/byte enable 1 (I/O/Z)
HRDY/PIRDY§ P4 I/O/Z Host ready from DSP to host (O) [default] or PCI initiator ready (I/O/Z).
HD31/AD31§ J2
HD30/AD30§ K3
HD29/AD29§ J1
HD28/AD28§ K4
HD27/AD27§ K2
HD26/AD26§ L3
HD25/AD25§ K1
HD24/AD24§ L4
HD23/AD23§ L1
HD22/AD22§ M4 Host-port data (I/O/Z) [default] (C64x) or PCI data-address bus (I/O/Z) [C6415T and C6416T]
HD21/AD21§ M2
As HPI data bus (PCI_EN pin = 0)
HD20/AD20§ N4 • Used for transfer of data, address, and control
HD19/AD19§ M1 • Host-Port bus width user-configurable at device reset via a 10-kΩ resistor pullup/pulldown
resistor on the HD5 pin:
HD18/AD18§ N5
HD17/AD17§ N1 HD5 pin = 0: HPI operates as an HPI16.
HD16/AD16§ P5 (HPI bus is 16 bits wide. HD[15:0] pins are used and the remaining HD[31:16] pins are
I/O/Z reserved pins in the high-impedance state.)
HD15/AD15§ U4
HD14/AD14§ U1 HD5 pin = 1: HPI operates as an HPI32.
HD13/AD13§ U3 (HPI bus is 32 bits wide. All HD[31:0] pins are used for host-port operations.)
HD12/AD12§ U2 As PCI data-address bus (PCI_EN pin = 1) [C6415T and C6416T devices only]
HD11/AD11§ V4 • Used for transfer of data and address
HD10/AD10§ V1
The C6414T device does not support the PCI peripheral; therefore, the HPI peripheral pins are
HD9/AD9§ V3 standalone peripheral functions, not muxed.
HD8/AD8§ V2
HD7/AD7§ W2
HD6/AD6§ W4
HD5/AD5§ Y1
HD4/AD4§ Y3
HD3/AD3§ Y2
HD2/AD2§ Y4
HD1/AD1§ AA1
HD0/AD0§ AA3
for this device.


SIGNAL IPD/
TYPE† DESCRIPTION
NAME NO. IPU‡
(CONTINUED)
PCI command/byte enable 0 (I/O/Z). When PCI is disabled (PCI_EN = 0), this pin is tied-off.
PCBE0 W3 I/O/Z For the C6414T device this pin is “Reserved (leave unconnected, do not connect to power or
ground).”
PCI serial interface chip select (O). When PCI is disabled (PCI_EN = 0), this pin is tied-off.
XSP_CS AD1 O IPD For the C6414T device this pin is “Reserved (leave unconnected, do not connect to power or
ground).”
CLKX2/
AC2 I/O/Z IPD McBSP2 transmit clock (I/O/Z) [default] or PCI serial interface clock (O).
XSP_CLK§
McBSP2 receive data (I) [default] or PCI serial interface data in (I). In PCI mode, this pin is
DR2/XSP_DI§ AB3 I IPU
connected to the output data pin of the serial PROM.
McBSP2 transmit data (O/Z) [default] or PCI serial interface data out (O). In PCI mode, this pin
DX2/XSP_DO§ AA2 O/Z IPU
is connected to the input data pin of the serial PROM.
GP15/PRST§ G3 General-purpose input/output (GPIO) 15 pin (I/O/Z) or PCI reset (I). No function at default.
GP14/PCLK§ F2 GPIO 14 pin (I/O/Z) or PCI clock (I). No function at default.
GP13/PINTA§ G4 GPIO 13 pin (I/O/Z) or PCI interrupt A (O/Z). No function at default.
GP12/PGNT§ J3 I/O/Z GPIO 12 pin (I/O/Z) or PCI bus grant (I). No function at default.
GP11/PREQ§ F1 GPIO 11 pin (I/O/Z) or PCI bus request (O/Z). No function at default.
GP10/PCBE3§ L2 GPIO 10 pin (I/O/Z) or PCI command/byte enable 3 (I/O/Z). No function at default.
GP9/PIDSEL§ M3 GPIO 9 pin (I/O/Z) or PCI initialization device select (I). No function at default.
EMIFA (64-bit) − CONTROL SIGNALS COMMON TO ALL TYPES OF MEMORY||
ACE3 L26 O/Z IPU
ACE2 K23 O/Z IPU EMIFA memory space enables
• Enabled by bits 28 through 31 of the word address
ACE1 K24 O/Z IPU • Only one pin is asserted during any external data access
ACE0 K25 O/Z IPU
ABE7 T23 O/Z IPU
ABE6 T24 O/Z IPU
ABE5 R25 O/Z IPU EMIFA byte-enable control
ABE4 R26 O/Z IPU • Decoded from the low-order address bits. The number of address bits or byte enables
used depends on the width of external memory.
ABE3 M25 O/Z IPU • Byte-write enables for most types of memory
ABE2 M26 O/Z IPU • Can be directly connected to SDRAM read and write mask signal (SDQM)
ABE1 L23 O/Z IPU
ABE0 L24 O/Z IPU
APDT M22 O/Z IPU EMIFA peripheral data transfer, allows direct transfer between external peripherals
for this device.
|| These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). The prefix “A” in front of a signal name indicates it is an EMIFA signal
To maintain signal integrity for the EMIF signals, serial termination resistors should be inserted into all EMIF output signal lines.


SIGNAL IPD/
TYPE† DESCRIPTION
NAME NO. IPU‡
EMIFA (64-BIT) − BUS ARBITRATION||
AHOLDA N22 O IPU EMIFA hold-request-acknowledge to the host
AHOLD V23 I IPU EMIFA hold request from the host
ABUSREQ P22 O IPU EMIFA bus request output
EMIFA (64-BIT) − ASYNCHRONOUS/SYNCHRONOUS MEMORY CONTROL||
EMIFA external input clock. The EMIFA input clock (AECLKIN, CPU/4 clock, or CPU/6 clock)
AECLKIN H25 I IPD is selected at reset via the pullup/pulldown resistors on the BEA[17:16] pins.
AECLKIN is the default for the EMIFA input clock.
EMIFA output clock 2. Programmable to be EMIFA input clock (AECLKIN, CPU/4 clock, or
AECLKOUT2 J23 O/Z IPD
CPU/6 clock) frequency divided-by-1, -2, or -4.
EMIFA output clock 1 [at EMIFA input clock (AECLKIN, CPU/4 clock, or CPU/6 clock)
AECLKOUT1 J26 O/Z IPD
frequency].
EMIFA asynchronous memory read-enable/SDRAM column-address strobe/programmable
synchronous interface-address strobe or read-enable
AARE/
• For programmable synchronous interface, the RENEN field in the CE Space Secondary
ASDCAS/ J25 O/Z IPU
Control Register (CExSEC) selects between ASADS and ASRE:
ASADS/ASRE
If RENEN = 0, then the ASADS/ASRE signal functions as the ASADS signal.
If RENEN = 1, then the ASADS/ASRE signal functions as the ASRE signal.
AAOE/
EMIFA asynchronous memory output-enable/SDRAM row-address strobe/programmable
ASDRAS/ J24 O/Z IPU
synchronous interface output-enable
ASOE
AAWE/
EMIFA asynchronous memory write-enable/SDRAM write-enable/programmable synchro-
ASDWE/ K26 O/Z IPU
nous interface write-enable
ASWE
EMIFA SDRAM clock-enable (used for self-refresh mode). [EMIFA module only.]
ASDCKE L25 O/Z IPU
• If SDRAM is not in system, ASDCKE can be used as a general-purpose output.
ASOE3 R22 O/Z IPU EMIFA synchronous memory output-enable for ACE3 (for glueless FIFO interface)
AARDY L22 I IPU Asynchronous memory ready input
EMIFA (64-BIT) − ADDRESS||
AEA22 T22
AEA21 V24
AEA20 V25
AEA19 V26
AEA18 U23
AEA17 U24
O/Z IPD EMIFA external address (doubleword address)
AEA16 U25
AEA15 U26
AEA14 T25
AEA13 T26
AEA12 R23
AEA11 R24


SIGNAL IPD/
TYPE† DESCRIPTION
NAME NO. IPU‡
EMIFA (64-BIT) − ADDRESS|| (CONTINUED)
AEA10 P23
AEA9 P24
AEA8 P26
AEA7 N23
O/Z IPD EMIFA external address (doubleword address)
AEA6 N24
AEA5 N26
AEA4 M23
AEA3 M24
EMIFA (64-bit) − DATA||
AED63 AF24
AED62 AF23
AED61 AE23
AED60 AE22
AED59 AD22
AED58 AF22
AED57 AD21
AED56 AE21
AED55 AC21
AED54 AF21
AED53 AD20
AED52 AE20
AED51 AC20
AED50 AF20 I/O/Z IPU EMIFA external data
AED49 AC19
AED48 AD19
AED47 W24
AED46 W23
AED45 Y26
AED44 Y23
AED43 Y25
AED42 Y24
AED41 AA26
AED40 AA23
AED39 AA25
AED38 AA24
AED37 AB26


SIGNAL IPD/
TYPE† DESCRIPTION
NAME NO. IPU‡
EMIFA (64-bit) − DATA|| (CONTINUED)
AED36 AB24
AED35 AB25
AED34 AC25
AED33 AC26
AED32 AD26
AED31 C26
AED30 D26
AED29 D25
AED28 E25
AED27 E24
AED26 E26
AED25 F24
AED24 F25
AED23 F23
AED22 F26
AED21 G24
AED20 G25
AED19 G23
AED18 G26 I/O/Z IPU EMIFA external data
AED17 H23
AED16 H24
AED15 C19
AED14 D19
AED13 A20
AED12 D20
AED11 B20
AED10 C20
AED9 A21
AED8 D21
AED7 B21
AED6 C21
AED5 A22
AED4 C22
AED3 B22
AED2 B23
AED1 A23
AED0 A24


SIGNAL IPD/
TYPE† DESCRIPTION
NAME NO. IPU‡
EMIFB (16-bit) − CONTROL SIGNALS COMMON TO ALL TYPES OF MEMORY||
BCE3 A13 O/Z IPU
BCE2 C12 O/Z IPU EMIFB memory space enables
• Enabled by bits 26 through 31 of the word address
BCE1 B12 O/Z IPU • Only one pin is asserted during any external data access
BCE0 A12 O/Z IPU
EMIFB byte-enable control
BBE1 D13 O/Z IPU
• Decoded from the low-order address bits. The number of address bits or byte enables
used depends on the width of external memory.
BBE0 C13 O/Z IPU • Byte-write enables for most types of memory
• Can be directly connected to SDRAM read and write mask signal (SDQM)
BPDT E12 O/Z IPU EMIFB peripheral data transfer, allows direct transfer between external peripherals
EMIFB (16-BIT) − BUS ARBITRATION||
BHOLDA E13 O IPU EMIFB hold-request-acknowledge to the host
BHOLD B19 I IPU EMIFB hold request from the host
BBUSREQ E14 O IPU EMIFB bus request output
EMIFB (16-BIT) − ASYNCHRONOUS/SYNCHRONOUS MEMORY CONTROL||
EMIFB external input clock. The EMIFB input clock (BECLKIN, CPU/4 clock, or CPU/6 clock)
BECLKIN A11 I IPD is selected at reset via the pullup/pulldown resistors on the BEA[15:14] pins.
BECLKIN is the default for the EMIFB input clock.
EMIFB output clock 2. Programmable to be EMIFB input clock (BECLKIN, CPU/4 clock, or
BECLKOUT2 D11 O/Z IPD
CPU/6 clock) frequency divided by 1, 2, or 4.
EMIFB output clock 1 [at EMIFB input clock (BECLKIN, CPU/4 clock, or CPU/6 clock)
BECLKOUT1 D12 O/Z IPD
frequency].
EMIFB asynchronous memory read-enable/SDRAM column-address strobe/programmable
synchronous interface-address strobe or read-enable
BARE/
• For programmable synchronous interface, the RENEN field in the CE Space Secondary
BSDCAS/ A10 O/Z IPU
Control Register (CExSEC) selects between BSADS and BSRE:
BSADS/BSRE
If RENEN = 0, then the BSADS/BSRE signal functions as the BSADS signal.
If RENEN = 1, then the BSADS/BSRE signal functions as the BSRE signal.
BAOE/
EMIFB asynchronous memory output-enable/SDRAM row-address strobe/programmable
BSDRAS/ B11 O/Z IPU
synchronous interface output-enable
BSOE
BAWE/BSDWE/ EMIFB asynchronous memory write-enable/SDRAM write-enable/programmable synchro-
C11 O/Z IPU
BSWE nous interface write-enable
BSOE3 E15 O/Z IPU EMIFB synchronous memory output enable for BCE3 (for glueless FIFO interface)
BARDY E11 I IPU EMIFB asynchronous memory ready input


SIGNAL IPD/
TYPE† DESCRIPTION
NAME NO. IPU‡
EMIFB (16-BIT) − ADDRESS||
EMIFB external address (half-word address) (O/Z)
BEA20 E16 IPU • Also controls initialization of DSP modes at reset (I) via pullup/pulldown resistors
− Device Endian mode
BEA19 D18 IPU BEA20: 0 – Big Endian
1 − Little Endian (default mode)
− Boot mode
BEA18 C18
BEA[19:18]: 00 – No boot
01 − HPI boot
BEA17 B18 10 − EMIFB 8-bit ROM boot with default timings (default mode)
11 − Reserved
BEA16 A18
− EMIF clock select
BEA[17:16]: Clock mode select for EMIFA (AECLKIN_SEL[1:0])
BEA15 D17 00 – AECLKIN (default mode)
BEA14 C17 10 − CPU/6 Clock Rate
11 − Reserved
BEA13 B17
BEA[15:14]: Clock mode select for EMIFB (BECLKIN_SEL[1:0])
00 – BECLKIN (default mode)
BEA12 A17 01 − CPU/4 Clock Rate
BEA11 D16 11 − Reserved
− PCI EEPROM Auto-Initialization (EEAI) [C6415T and C6416T devices only]

BEA10 C16 BEA13: PCI auto-initialization via external EEPROM
I/O/Z IPD If the PCI peripheral is disabled (PCI_EN pin = 0), this pin must not be pulled up.
BEA9 B16 0 − PCI auto-initialization through EEPROM is disabled (default).
1 − PCI auto-initialization through EEPROM is enabled.
BEA8 A16
− UTOPIA Enable (UTOPIA_EN) [C6415T and C6416T devices only]
BEA11: UTOPIA peripheral enable (functional)
BEA7 D15 0 − UTOPIA disabled (McBSP1 enabled) [default]
1 − UTOPIA enabled (McBSP1 disabled)
BEA6 C15
The C6414T device does not support the PCI and UTOPIA peripherals; for proper device
operation, do not oppose the internal pulldowns (IPDs) on the BEA13 and BEA11 pins.
BEA5 B15
Also for proper C6414T device operation, do not oppose the IPDs on the BEA7, BEA8,
BEA4 A15 and BEA9 pins.
For proper C6415T device operation, the BEA7 pin must be externally pulled up with a
BEA3 D14
1-k
1-kΩ resistor.
BEA2 C14 For proper C6416T device operation, the BEA8 and BEA9 pins must be externally
pulled up with a 1-kΩ resistor.
BEA1 A14
For more details, see the Device Configurations section of this data sheet.


SIGNAL IPD/
TYPE† DESCRIPTION
NAME NO. IPU‡
EMIFB (16-bit) − DATA||
BED15 D7
BED14 B6
BED13 C7
BED12 A6
BED11 D8
BED10 B7
BED9 C8
BED8 A7
I/O/Z IPU EMIFB external data
BED7 C9
BED6 B8
BED5 D9
BED4 B9
BED3 C10
BED2 A9
BED1 D10
BED0 B10
MULTICHANNEL BUFFERED SERIAL PORT 2 (McBSP2)
McBSP2 enable pin. This pin works in conjunction with the PCI_EN pin to enable/disable other
MCBSP2_EN AF3 I IPD
peripherals (for more details, see the Device Configurations section of this data sheet).
McBSP2 external clock source (CLKS2) [input only] [default] or this pin can also be
CLKS2/GP8§ AE4 I/O/Z IPD
programmed as a GPIO 8 pin (I/O/Z).
McBSP2 receive clock. When McBSP2 is disabled (PCI_EN pin = 1 and MCBSP2_EN
CLKR2 AB1 I/O/Z IPD
pin = 0), this pin is tied-off.
CLKX2/
AC2 I/O/Z IPD McBSP2 transmit clock (I/O/Z) [default] or PCI serial interface clock (O).
XSP_CLK§
McBSP2 receive data (I) [default] or PCI serial interface data in (I). In PCI mode, this pin is
DR2/XSP_DI§ AB3 I IPU
connected to the output data pin of the serial PROM.
McBSP2 transmit data (O/Z) [default] or PCI serial interface data out (O). In PCI mode, this pin
DX2/XSP_DO§ AA2 O/Z IPU
is connected to the input data pin of the serial PROM.
McBSP2 receive frame sync. When McBSP2 is disabled (PCI_EN pin = 1 and MCBSP2_EN
FSR2 AC1 I/O/Z IPD
McBSP2 transmit frame sync. When McBSP2 is disabled (PCI_EN pin = 1 and MCBSP2_EN
FSX2 AB2 I/O/Z IPD
The C6414T device does not support the PCI or UTOPIA peripherals; therefore, these muxed peripheral pins except CLKS2/GP8 are standalone
peripheral functions for this device.


SIGNAL IPD/
TYPE† DESCRIPTION
NAME NO. IPU‡
CLKS1/ McBSP1 external clock source (as opposed to internal) (I) [default] or UTOPIA receive
AC8 I
URADDR3§ address 3 pin (I)
CLKR1/
AC10 I/O/Z McBSP1 receive clock (I/O/Z) [default] or UTOPIA receive address 2 pin (I)
URADDR2§
CLKX1/
AB12 I/O/Z McBSP1 transmit clock (I/O/Z) [default] or UTOPIA receive address 4 pin (I)
URADDR4§
DR1/
AF11 I McBSP1 receive data (I) [default] or UTOPIA transmit address 1 pin (I)
UXADDR1§
DX1/
AB11 I/O/Z McBSP1 transmit data (O/Z) [default] or UTOPIA transmit address 4 pin (I)
UXADDR4§
FSR1/
AC9 I/O/Z McBSP1 receive frame sync (I/O/Z) [default] or UTOPIA transmit address 2 pin (I)
UXADDR2§
FSX1/
AB13 I/O/Z McBSP1 transmit frame sync (I/O/Z) [default] or UTOPIA transmit address 3 pin (I)
UXADDR3§
CLKS0 F4 I IPD McBSP0 external clock source (as opposed to internal)
CLKR0 D1 I/O/Z IPD McBSP0 receive clock
CLKX0 E1 I/O/Z IPD McBSP0 transmit clock
DR0 D2 I IPU McBSP0 receive data
DX0 E2 O/Z IPU McBSP0 transmit data
FSR0 C1 I/O/Z IPD McBSP0 receive frame sync
FSX0 E3 I/O/Z IPD McBSP0 transmit frame sync
TIMER 2
TOUT2 A4 O/Z IPD Timer 2 or general-purpose output
TINP2 C5 I IPD Timer 2 or general-purpose input
TIMER 1
TOUT1 B5 O/Z IPD Timer 1 or general-purpose output
TINP1 A5 I IPD Timer 1 or general-purpose input
TIMER 0
TOUT0 D6 O/Z IPD Timer 0 or general-purpose output
TINP0 C6 I IPD Timer 0 or general-purpose input
for this device.


SIGNAL IPD/
TYPE† DESCRIPTION
NAME NO. IPU‡
UNIVERSAL TEST AND OPERATIONS PHY INTERFACE FOR ASYNCHRONOUS TRANSFER MODE (ATM) [UTOPIA SLAVE]
[C6415T and C6416T devices only]
UTOPIA SLAVE (ATM CONTROLLER) − TRANSMIT INTERFACE
Source clock for UTOPIA transmit driven by Master ATM Controller.
UXCLKY AD11 I
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
Transmit cell available status output signal from UTOPIA Slave.
0 indicates a complete cell is NOT available for transmit
UXCLAVY AC14 O/Z 1 indicates a complete cell is available for transmit
UTOPIA transmit interface enable input signal. Asserted by the Master ATM Controller to indi-
cate that the UTOPIA Slave should put out on the Transmit Data Bus the first byte of valid data
UXENBY AE15 I ◊
and the UXSOC signal in the next clock cycle.
Transmit Start-of-Cell signal. This signal is output by the UTOPIA Slave on the rising edge of
the UXCLK, indicating that the first valid byte of the cell is available on the 8-bit Transmit Data
UXSOCY AC13 O/Z
Bus (UXDATA[7:0]).
McBSP1 [default] or UTOPIA transmit address pins
As UTOPIA transmit address pins UXADDR[4:0] (I), UTOPIA_EN (BEA11 pin) = 1:

• 5-bit Slave transmit address input pins driven by the Master ATM Controller to identify and
select one of the Slave devices (up to 31 possible) in the ATM System.
DX1/
AB11 I/O/Z ◊
UXADDR4§
• UXADDR0 pin is tied off when the UTOPIA peripheral is disabled [UTOPIA_EN
(BEA11 pin) = 0]
For the McBSP1 pin functions (UTOPIA_EN (BEA11 pin) = 0 [default]), see the MULTICHAN-
NEL BUFFERED SERIAL PORT 1 (McBSP1) section of this table.
FSX1/ McBSP1 [default] or UTOPIA transmit address pins

AB13 I/O/Z ◊
UXADDR3§
As UTOPIA transmit address pins UXADDR[4:0] (I), UTOPIA_EN (BEA11 pin) = 1:
• 5-bit Slave transmit address input pins driven by the Master ATM Controller to identify and
FSR1/
AC9 I/O/Z ◊ select one of the Slave devices (up to 31 possible) in the ATM System.
UXADDR2§
• UXADDR0 pin is tied off when the UTOPIA peripheral is disabled [UTOPIA_EN
DR1/
AF11 I ◊ (BEA11 pin) = 0]
UXADDR1§
For the McBSP1 pin functions (UTOPIA_EN (BEA11 pin) = 0 [default]), see the MULTICHAN-
UXADDR0Y AE9 I ◊
NEL BUFFERED SERIAL PORT 1 (McBSP1) section of this table.
for this device.
For the C6415T and C6416T devices, external pulldowns required: If UTOPIA is selected (BEA11 = 1) and these pins are connected to other
devices, then a 10-kΩ resistor must be used to externally pull down each of these pins. If these pins are “no connects”, then only UXCLK and
URCLK need to be pulled down and other pulldowns are not necessary.
◊ For the C6415T and C6416T devices, external pullups required: If UTOPIA is selected (BEA11 = 1) and these pins are connected to other devices,
then a 10-kΩ resistor must be used to externally pull up each of these pins. If these pins are “no connects”, then the pullups are not necessary.
Ψ The C6414T device does not support the UTOPIA peripheral; therefore, these standalone UTOPIA pins are Reserved (leave unconnected, do
not connect to power or ground) with the exception of UXCLK and URCLK which should be connected to a 10-kΩ pulldown resistor (see the
square [] footnote).


SIGNAL IPD/
TYPE† DESCRIPTION
NAME NO. IPU‡
UTOPIA SLAVE (ATM CONTROLLER) − TRANSMIT INTERFACE (CONTINUED)
UXDATA7Y AD10
UXDATA6Y AD9
UXDATA5Y AD8 8-bit Transmit Data Bus
UXDATA4Y AE8 Using the Transmit Data Bus, the UTOPIA Slave (on the rising edge of the UXCLK) transmits
O/Z the 8-bit ATM cells to the Master ATM Controller.
UXDATA3Y AF9 When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), these pins are tied-
UXDATA2Y AF7 off.
UXDATA1Y AE7
UXDATA0Y AD7
UTOPIA SLAVE (ATM CONTROLLER) − RECEIVE INTERFACE
Source clock for UTOPIA receive driven by Master ATM Controller.
URCLKY AD12 I
Receive cell available status output signal from UTOPIA Slave.
0 indicates NO space is available to receive a cell from Master ATM Controller
URCLAVY AF14 O/Z 1 indicates space is available to receive a cell from Master ATM Controller
UTOPIA receive interface enable input signal. Asserted by the Master ATM Controller to indi-
cate to the UTOPIA Slave to sample the Receive Data Bus (URDATA[7:0]) and URSOC signal
URENBY AD15 I ◊
in the next clock cycle or thereafter.
Receive Start-of-Cell signal. This signal is output by the Master ATM Controller to indicate to
the UTOPIA Slave that the first valid byte of the cell is available to sample on the 8-bit Receive
URSOCY AB14 I
Data Bus (URDATA[7:0]).
CLKX1/ McBSP1 [default] or UTOPIA receive address pins
AB12 I/O/Z ◊
URADDR4§
As UTOPIA receive address pins URADDR[4:0] (I), UTOPIA_EN (BEA11 pin) = 1:
CLKS1/ • 5-bit Slave receive address input pins driven by the Master ATM Controller to identify and
AC8 I ◊
URADDR3§ select one of the Slave devices (up to 31 possible) in the ATM System.
CLKR1/
AC10 I/O/Z ◊ • URADDR1 and URADDR0 pins are tied off when the UTOPIA peripheral is disabled
URADDR2§
[UTOPIA_EN (BEA11 pin) = 0]
URADDR1Y AF10 I ◊
For the McBSP1 pin functions (UTOPIA_EN (BEA11 pin) = 0 [default]), see the
URADDR0Y AE10 I ◊ MULTICHANNEL BUFFERED SERIAL PORT 1 (McBSP1) section of this table.
§ These pins are multiplexed pins. For more details, see the Device Configurations section of this data sheet.
External pulldowns required: If UTOPIA is selected (BEA11 = 1) and these pins are connected to other devices, then a 10-kΩ resistor must be
used to externally pull down each of these pins. If these pins are “no connects”, then only UXCLK and URCLK need to be pulled down and other
pulldowns are not necessary.
◊ External pullups required: If UTOPIA is selected (BEA11 = 1) and these pins are connected to other devices, then a 10-kΩ resistor must be used
to externally pull up each of these pins. If these pins are “no connects”, then the pullups are not necessary.


SIGNAL IPD/
TYPE† DESCRIPTION
NAME NO. IPU‡
UTOPIA SLAVE (ATM CONTROLLER) − RECEIVE INTERFACE (CONTINUED)
URDATA7Ψ AF12
URDATA6Ψ AE11
URDATA5Ψ AF13 8-bit Receive Data Bus.
URDATA4Ψ AC11 Using the Receive Data Bus, the UTOPIA Slave (on the rising edge of the URCLK) can receive
I the 8-bit ATM cell data from the Master ATM Controller.
URDATA3Ψ AC12 When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), these pins are tied-
URDATA2Ψ AE12 off.
URDATA1Ψ AD14
URDATA0Ψ AD13
RESERVED FOR TEST
G14
H7
RSV N20 Reserved. These pins must be connected directly to CVDD for proper device operation.
P7
Y13
RSV R6 Reserved. This pin must be connected directly to DVDD for proper device operation.
A3
G2
H3
J4 Reserved (leave unconnected, do not connect to power or ground. If the signal must be
RSV routed out from the device, the internal pull−up/down resistance should not be relied upon and
K6 an external pull−up/down should be used).
N3
P3
W25 IPD
External pulldowns required: If UTOPIA is selected (BEA11 = 1) and these pins are connected to other devices, then a 10-kΩ resistor must be
used to externally pull down each of these pins. If these pins are “no connects”, then only UXCLK and URCLK need to be pulled down and other
pulldowns are not necessary.


SIGNAL
TYPE† DESCRIPTION
NAME NO.
SUPPLY VOLTAGE PINS
A2
A25
B1
B14
B26
E7
E8
E10
E17
E19
E20
F3
F9
F12
F15
F18
G5
G22
H5
H22 3.3-V supply voltage
DVDD S
J21 (see the Power-Supply Decoupling section of this data sheet)
K5
K22
L5
M5
M6
M21
N2
P25
R5
R21
T5
U5
U22
V6
V21
W5
W22
Y5
Y22


SIGNAL
TYPE† DESCRIPTION
NAME NO.
SUPPLY VOLTAGE PINS (CONTINUED)
AA9
AA12
AA15
AA18
AB7
AB8
AB10
3.3-V supply voltage
DVDD AB17
(see the Power-Supply Decoupling section of this data sheet)
AB19
AB20
AE1
AE13
AE26
AF2
AF25
A1
A26
B2
B25
C3 S
C24
D4
D23
E5
E22
F6
F7 1.1-V supply voltage (-600 device)
CVDD 1.2 V supply voltage (-720, -850, -1G devices)
F20 (see the Power-Supply Decoupling section of this data sheet)
F21
G6
G7
G8
G10
G11
G13
G16
G17
G19
G20


SIGNAL
TYPE† DESCRIPTION
NAME NO.
SUPPLY VOLTAGE PINS (CONTINUED)
G21
H20
K7
K20
L7
L20
N7
P20
T7
T20
U7
U20
W7
W20
Y6
Y7
Y8
Y10
Y11 1.1-V supply voltage (-600 device)
CVDD Y14 S 1.2 V supply voltage (-720, -850, -1G devices)
Y16 (see the Power-Supply Decoupling section of this data sheet)
Y17
Y19
Y20
Y21
AA6
AA7
AA20
AA21
AB5
AB22
AC4
AC23
AD3
AD24
AE2
AE25
AF1
AF26


SIGNAL
TYPE† DESCRIPTION
NAME NO.
GROUND PINS
A8
A19
B3
B13
B24
C2
C4
C23
C25
D3
D5
D22
D24
E4
E6
E9
E18
E21
E23
VSS F5 GND Ground pins
F8
F10
F11
F13
F14
F16
F17
F19
F22
G9
G12
G15
G18
H1
H6
H21
H26
J5
J7


SIGNAL
TYPE† DESCRIPTION
NAME NO.
GROUND PINS (CONTINUED)
J20
J22
K21
L6
L21
M7
M20
N6
N21
N25
P2
P6
P21
R7
R20
T6
T21
U6
U21
VSS V5 GND Ground pins
V7
V20
V22
W1
W6
W21
W26
Y9
Y12
Y15
Y18
AA5
AA8
AA10
AA11
AA13
AA14
AA16
AA17


SIGNAL
TYPE† DESCRIPTION
NAME NO.
GROUND PINS (CONTINUED)
AA19
AA22
AB4
AB6
AB9
AB18
AB21
AB23
AC3
AC5
VSS AC22 GND Ground pins
AC24
AD2
AD4
AD23
AD25
AE3
AE14
AE24
AF8
AF19

development support
TI offers an extensive line of development tools for the TMS320C6000 DSP platform, including tools to
evaluate the performance of the processors, generate code, develop algorithm implementations, and fully
integrate and debug software and hardware modules.
The following products support development of C6000 DSP-based applications:
Software Development Tools:
Code Composer Studio Integrated Development Environment (IDE): including Editor
C/C++/Assembly Code Generation, and Debug plus additional development tools
Scalable, Real-Time Foundation Software (DSP/BIOS), which provides the basic run-time target software
needed to support any DSP application.
Hardware Development Tools:
Extended Development System (XDS) Emulator (supports C6000 DSP multiprocessor system debug)
EVM (Evaluation Module)
For a complete listing of development-support tools for the TMS320C6000 DSP platform, visit the Texas
Instruments web site on the Worldwide Web at http://www.ti.com uniform resource locator (URL). For
information on pricing and availability, contact the nearest TI field sales office or authorized distributor.
Code Composer Studio, DSP/BIOS, and XDS are trademarks of Texas Instruments.

device support
device and development-support tool nomenclature
To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all DSP
devices and support tools. Each DSP commercial family member has one of three prefixes: TMX, TMP, or TMS.
(e.g., TMS320C6415TGLZ7) Texas Instruments recommends two of three possible prefix designators for its
support tools: TMDX and TMDS. These prefixes represent evolutionary stages of product development from
engineering prototypes (TMX / TMDX) through fully qualified production devices/tools (TMS / TMDS).
Device development evolutionary flow:
TMX Experimental device that is not necessarily representative of the final device’s electrical
specifications
TMP Final silicon die that conforms to the device’s electrical specifications but has not completed
quality and reliability verification
TMS Fully qualified production device
Support tool development evolutionary flow:
TMDX Development-support product that has not yet completed Texas Instruments internal qualification
testing
TMDS Fully qualified development-support product

TMX and TMP devices and TMDX development-support tools are shipped against the following disclaimer:
“Developmental product is intended for internal evaluation purposes.”
TMS devices and TMDS development-support tools have been characterized fully, and the quality and reliability
of the device have been demonstrated fully. TI’s standard warranty applies.
Predictions show that prototype devices (TMX or TMP) have a greater failure rate than the standard production
devices. Texas Instruments recommends that these devices not be used in any production system because their
expected end-use failure rate still is undefined. Only qualified production devices are to be used.
TI device nomenclature also includes a suffix with the device family name. This suffix indicates the package type
(for example, GLZ), the temperature range (for example, “blank” is the default commercial temperature range),
and the device speed range in megahertz (for example, 7 is 720-MHz). Figure 5 provides a legend for reading
the complete device name for any TMS320C64x DSP generation member.
The ZLZ package, like the GLZ package, is a 532-ball plastic BGA only with Pb-free balls. The CLZ is the
Pb−Free die bump and solder ball version of GLZ and ZLZ. For device part numbers and further ordering
information for TMS320C6414T/TMS320C6415T/TMS320C6416T in the GLZ, ZLZ and CLZ package types,
see the TI website (http://www.ti.com) or contact your TI sales representative.

device and development-support tool nomenclature (continued)
TMS 320 C 6415T GLZ ( ) 7
PREFIX DEVICE SPEED RANGE

TMX = Experimental device 6 (600-MHz CPU, 133-MHz EMIFA)
TMP = Prototype device 7 (720-MHz CPU, 133-MHz EMIFA)
TMS = Qualified device 8 (850-MHz CPU, 133 MHz EMIFA)
SMX= Experimental device, MIL 1 (1-GHz CPU, 133-MHz EMIFA)
SMJ = MIL-PRF-38535, QML
SM = High Rel (non-38535) TEMPERATURE RANGE (DEFAULT: 0°C TO 90°C)†‡
Blank = 0°C to 90°C, commercial temperature
M = 0°C to 90°C, commercial temperature
A = −40°C to 105°C, extended temperature
DEVICE FAMILY D = −40°C to 90°C, partial extended temperature
3 or 32 or 320 = TMS320 DSP family
PACKAGE TYPE§#||
GLZ = 532-pin plastic BGA
ZLZ = 532-pin plastic BGA, with Pb−free soldered balls
TECHNOLOGY CLZ = Pb−Free die bump and solder ball version of
C = CMOS GLZ and ZLZ
DEVICE¶
C64x DSP:
6414T
6415T
6416T
† The extended temperature “A version” devices may have different operating conditions than the commercial temperature devices.
‡ See the Recommended Operating Conditions section of this data sheet for more details.
§ BGA = Ball Grid Array
¶ For the actual device part numbers (P/Ns) and ordering information, see the TI website (www.ti.com).
# The ZLZ mechanical package designator represents the version of the GLZ with Pb−Free soldered balls.
|| The CLZ mechanical package designator represents the version of the GLZ and ZLZ with Pb−Free die bump and solder balls.
Figure 5. TMS320C64x DSP Device Nomenclature (Including the C6414T, C6415T, and C6416T Devices)
For additional information, see the TMS320C6414T, TMS320C6415T, and TMS320C6416T Digital Signal
Processors Silicon Errata (literature number SPRZ216)

documentation support
Extensive documentation supports all TMS320 DSP family generations of devices from product
announcement through applications development. The types of documentation available include: data sheets,
such as this document, with design specifications; complete user’s reference guides for all devices and tools;
technical briefs; development-support tools; on-line help; and hardware and software applications. The
following is a brief, descriptive list of support documentation specific to the C6000 DSP devices:
The TMS320C6000 CPU and Instruction Set Reference Guide (literature number SPRU189) describes the
C6000 DSP CPU (core) architecture, instruction set, pipeline, and associated interrupts.
The TMS320C6000 DSP Peripherals Overview Reference Guide (literature number SPRU190) provides an
overview and briefly describes the functionality of the peripherals available on the C6000 DSP platform of
devices. This document also includes a table listing the peripherals available on the C6000 devices along with
literature numbers and hyperlinks to the associated peripheral documents.
The TMS320C6000 Technical Brief (literature number SPRU197) gives an introduction to the
TMS320C62x/TMS320C67x devices, associated development tools, and third-party support.
The TMS320C64x Technical Overview (literature number SPRU395) gives an introduction to the C64x digital
signal processor, and discusses the application areas that are enhanced by the C64x DSP VelociTI.2 VLIW
architecture.
The TMS320C6414T, TMS320C6415T, and TMS320C6416T Digital Signal Processors Silicon Errata
(literature number SPRZ216) describes the known exceptions to the functional specifications for the
TMS320C6414T, TMS320C6415T, and TMS320C6416T devices.
The Using IBIS Models for Timing Analysis application report (literature number SPRA839) describes how to
properly use IBIS models to attain accurate timing analysis for a given system.
The Migrating From TMS320C6416/15/14 to TMS320C6416T/15T/14T application report (literature number

SPRA981) provides more detailed information on the device compatibility, similarities/differences, and
migration from a TMS320C6416 device to the TMS320C6414T/C6415T/C6416T devices.
The tools support documentation is electronically available within the Code Composer Studio Integrated
Development Environment (IDE). For a complete listing of C6000 DSP latest documentation, visit the Texas
Instruments web site on the Worldwide Web at http://www.ti.com uniform resource locator (URL).

clock PLL
Most of the internal C64x DSP clocks are generated from a single source through the CLKIN pin. This source
clock either drives the PLL, which multiplies the source clock frequency to generate the internal CPU clock, or
bypasses the PLL to become the internal CPU clock.
To use the PLL to generate the CPU clock, the external PLL filter circuit must be properly designed. Figure 6
shows the external PLL circuitry for either x1 (PLL bypass) or other PLL multiply modes.
To ensure proper operation of the PLL, a specified power-on reset sequence must be followed. For more detail
on the specified power-on reset sequence, see the power-supply sequencing section of this data sheet.
To minimize the clock jitter, a single clean power supply should power both the C64x DSP device and the
external clock oscillator circuit. The minimum CLKIN rise and fall times should also be observed. For the input
clock timing requirements, see the input and output clocks electricals section.
Rise/fall times, duty cycles (high/low pulse durations), and the load capacitance of the external clock source
must meet the DSP requirements in this data sheet (see the electrical characteristics over recommended
ranges of supply voltage and operating case temperature table and the input and output clocks electricals
section). Table 30 lists some examples of compatible CLKIN external clock sources:
Table 30. Compatible CLKIN External Clock Sources

COMPATIBLE PARTS FOR
PART NUMBER MANUFACTURER
EXTERNAL CLOCK SOURCES (CLKIN)
JITO-2 Fox Electronix
STA series, ST4100 series SaRonix Corporation
Oscillators
SG-636 Epson America
342 Corning Frequency Control
PLL ICS525-02 Integrated Circuit Systems

clock PLL (continued)
3.3 V
CPU Clock
C1 C2
EMI /2 Peripheral Bus
filter 10 µF 0.1 µF
/8 Timer Internal Clock
PLLV
/4 CLKOUT4,
McBSP Internal Clock
CLKMODE0
PLLMULT /6 CLKOUT6
CLKMODE1
PLL
x6, x12, x20
00 01 10 ECLKIN_SEL (DEVCFG.[17,16]
CLKIN PLLCLK 1 and DEVCFG.[15,14])
0 /4
/2
ECLKIN
EMIF 00 01 10 EK2RATE
Internal to C64x (GBLCTL.[19,18])
(For the PLL Options, CLKMODE Pins Setup, and ECLKOUT1 ECLKOUT2
PLL Clock Frequency Ranges, see Table 31.)
NOTES: A. Place all PLL external components (C1, C2, and the EMI Filter) as close to the C6000 DSP device as possible. For the best
performance, TI recommends that all the PLL external components be on a single side of the board without jumpers, switches, or
components other than the ones shown.
B. For reduced PLL jitter, maximize the spacing between switching signals and the PLL external components (C1, C2, and the EMI
Filter).
C. The 3.3-V supply for the EMI filter must be from the same 3.3-V power plane supplying the I/O voltage, DVDD.
D. EMI filter manufacturer TDK part number ACF451832-333, -223, -153, -103. Panasonic part number EXCCET103U.
Figure 6. External PLL Circuitry for Either PLL Multiply Modes or x1 (Bypass) Mode

clock PLL (continued)
Table 31. TMS320C64x PLL Multiply Factor Options, Clock Frequency Ranges, and Typical Lock Time†‡
GLZ, ZLZ and CLZ PACKAGES − 23 x 23 mm BGA
CLKMODE CLKIN CPU CLOCK TYPICAL
CLKOUT4 CLKOUT6
CLKMODE1 CLKMODE0 (PLL MULTIPLY RANGE FREQUENCY LOCK TIME
RANGE (MHz) RANGE (MHz)
FACTORS) (MHz) RANGE (MHz) (µs)§
0 0 Bypass (x1) 0−100 0−100 0−25 0−16.6 N/A
0 1 x6 42−75 252−450 63−112.5 42−75
1 0 x12 42−75 504−900 126−225 84−150 75
1 1 x20 25−50 500−1000 125−250 83.3−166.6
† These clock frequency range values are applicable to a C64x−600, −720, −850, and −1000-MHz speed devices. For more detailed information,
see the CLKIN timing requirements table for the specific device speed.
‡ Use external pullup resistors on the CLKMODE pins (CLKMODE1 and CLKMODE0) to set the C64x device to one of the valid PLL multiply clock
modes (x6, x12, or x20). With internal pulldown resistors on the CLKMODE pins (CLKMODE1, CLKMODE0), the default clock mode is
x1 (bypass).
§ Under some operating conditions, the maximum PLL lock time may vary by as much as 150% from the specified typical value. For example, if
the typical lock time is specified as 100 µs, the maximum value may be as long as 250 µs.

general-purpose input/output (GPIO)

To use the GP[15:0] software-configurable GPIO pins, the GPxEN bits in the GP Enable (GPEN) Register and
the GPxDIR bits in the GP Direction (GPDIR) Register must be properly configured.
GPxEN = 1 GP[x] pin is enabled
GPxDIR = 0 GP[x] pin is an input
GPxDIR = 1 GP[x] pin is an output
where “x” represents one of the 15 through 0 GPIO pins
Figure 7 shows the GPIO enable bits in the GPEN register for the C6414T/C6415T/C6416T device. To use any
of the GPx pins as general-purpose input/output functions, the corresponding GPxEN bit must be set to “1”
(enabled). Default values are device-specific, so refer to Figure 7 for the C6414T/15T/16T default configuration.
31 24 23 16
Reserved
R-0
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
GP15 GP14 GP13 GP12 GP11 GP10 GP9 GP8 GP7 GP6 GP5 GP4 GP3 GP2 GP1 GP0
EN EN EN EN EN EN EN EN EN EN EN EN EN EN EN EN
R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-0 R/W-0 R/W-1
Legend: R/W = Readable/Writeable; -n = value after reset, -x = undefined value after reset
Figure 7. GPIO Enable Register (GPEN) [Hex Address: 01B0 0000]
Figure 8 shows the GPIO direction bits in the GPDIR register. This register determines if a given GPIO pin is
an input or an output providing the corresponding GPxEN bit is enabled (set to “1”) in the GPEN register. By
default, all the GPIO pins are configured as input pins.
31 24 23 16
Reserved
R-0
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
GP15 GP14 GP13 GP12 GP11 GP10 GP9 GP8 GP7 GP6 GP5 GP4 GP3 GP2 GP1 GP0
DIR DIR DIR DIR DIR DIR DIR DIR DIR DIR DIR DIR DIR DIR DIR DIR
R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0
Legend: R/W = Readable/Writeable; -n = value after reset, -x = undefined value after reset
Figure 8. GPIO Direction Register (GPDIR) [Hex Address: 01B0 0004]
For more detailed information on general-purpose inputs/outputs (GPIOs), see the TMS320C6000 DSP
General-Purpose Input/Output (GPIO) Reference Guide (literature number SPRU584).

power-down mode logic

Figure 9 shows the power-down mode logic on the C6414T/C6415T/C6416T.
CLKOUT4 CLKOUT6
Internal Clock Tree

Clock
Distribution
and Dividers
PD1
PD2
IFR
Power-
Clock Internal
Down IER
PLL Peripherals
Logic
PWRD CSR
CPU
PD3
TMS320C6414T/15T/16T
CLKIN RESET
† External input clocks, with the exception of CLKIN, are not gated by the power-down mode logic.
Figure 9. Power-Down Mode Logic†
triggering, wake-up, and effects

The power-down modes and their wake-up methods are programmed by setting the PWRD field (bits 15−10)
of the control status register (CSR). The PWRD field of the CSR is shown in Figure 10 and described in Table 32.
When writing to the CSR, all bits of the PWRD field should be set at the same time. Logic 0 should be used when
writing to the reserved bit (bit 15) of the PWRD field. The CSR is discussed in detail in the TMS320C6000 CPU
and Instruction Set Reference Guide (literature number SPRU189).

31 16
15 14 13 12 11 10 9 8
Enable or
Enabled
Reserved Non-Enabled PD3 PD2 PD1
Interrupt Wake
Interrupt Wake
R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0
7 0
Legend: R/W−x = Read/write reset value

NOTE: The shadowed bits are not part of the power-down logic discussion and therefore are not covered here. For information on these other
bit fields in the CSR register, see the TMS320C6000 CPU and Instruction Set Reference Guide (literature number SPRU189).
Figure 10. PWRD Field of the CSR Register
A delay of up to nine clock cycles may occur after the instruction that sets the PWRD bits in the CSR before the
PD mode takes effect. As best practice, NOPs should be padded after the PWRD bits are set in the CSR to account
for this delay.
If PD1 mode is terminated by a non-enabled interrupt, the program execution returns to the instruction where
PD1 took effect. If PD1 mode is terminated by an enabled interrupt, the interrupt service routine will be executed
first, then the program execution returns to the instruction where PD1 took effect. In the case with an enabled
interrupt, the GIE bit in the CSR and the NMIE bit in the interrupt enable register (IER) must also be set in order
for the interrupt service routine to execute; otherwise, execution returns to the instruction where PD1 took effect
upon PD1 mode termination by an enabled interrupt.
PD2 and PD3 modes can only be aborted by device reset. Table 32 summarizes all the power-down modes.
Table 32. Characteristics of the Power-Down Modes
PRWD FIELD POWER-DOWN

WAKE-UP METHOD EFFECT ON CHIP’S OPERATION
(BITS 15−10) MODE
000000 No power-down — —
CPU halted (except for the interrupt logic)
001001 PD1 Wake by an enabled interrupt
Power-down mode blocks the internal clock inputs at the
boundary of the CPU, preventing most of the CPU’s logic from
Wake by an enabled or switching. During PD1, EDMA transactions can proceed
010001 PD1
non-enabled interrupt between peripherals and internal memory.
Output clock from PLL is halted, stopping the internal clock
structure from switching and resulting in the entire chip being
011010 PD2† Wake by a device reset halted. All register and internal RAM contents are preserved. All
functional I/O “freeze” in the last state when the PLL clock is
turned off.
† When entering PD2 and PD3, all functional I/O remains in the previous state. However, for peripherals which are asynchronous in nature or
peripherals with an external clock source, output signals may transition in response to stimulus on the inputs. Under these conditions,
peripherals will not operate according to specifications.

Table 32. Characteristics of the Power-Down Modes
PRWD FIELD POWER-DOWN

WAKE-UP METHOD EFFECT ON CHIP’S OPERATION
(BITS 15−10) MODE
Input clock to the PLL stops generating clocks. All register and
internal RAM contents are preserved. All functional I/O “freeze” in
the last state when the PLL clock is turned off. Following reset, the
011100 PD3† Wake by a device reset
PLL needs time to re-lock, just as it does following power-up.
Wake-up from PD3 takes longer than wake-up from PD2 because
the PLL needs to be re-locked, just as it does following power-up.
All others Reserved — —
† When entering PD2 and PD3, all functional I/O remains in the previous state. However, for peripherals which are asynchronous in nature or
peripherals with an external clock source, output signals may transition in response to stimulus on the inputs. Under these conditions,
peripherals will not operate according to specifications.
C64x power-down mode with an emulator

If user power-down modes are programmed, and an emulator is attached, the modes will be masked to allow
the emulator access to the system. This condition prevails until the emulator is reset or the cable is removed
from the header. If power measurements are to be performed when in a power-down mode, the emulator cable
should be removed.
When the DSP is in power-down mode PD2 or PD3, emulation logic will force any emulation execution
command (such as Step or Run) to spin in IDLE. For this reason, PC writes (such as loading code) will fail. A DSP
reset will be required to get the DSP out of PD2/PD3.
power-supply sequencing
TI DSPs typically do not require specific power sequencing between the core supply and the I/O supply.
However, systems should be designed to ensure that the Core is powered up prior to the I/O supply and that
the I/O supply is powered up within ≤ 200 ms of the core. This power sequence becomes even more important
in multiprocessor designs.
In addition, for proper device initialization, device reset (RESET) must be held active (low) during device power
ramp and should not be released until the PLL becomes stable.
power-supply design considerations
A dual-power supply with simultaneous sequencing can be used to eliminate the delay between core and I/O
power up. A Schottky diode can also be used to tie the core rail to the I/O rail (see Figure 11).

I/O Supply
DVDD
Schottky
Diode
C6000
Core Supply
DSP
CVDD
VSS
GND
Figure 11. Schottky Diode Diagram
Core and I/O supply voltage regulators should be located close to the DSP (or DSP array) to minimize
inductance and resistance in the power delivery path. Additionally, when designing for high-performance
applications utilizing the C6000 platform of DSPs, the PC board should include separate power planes for
core, I/O, and ground, all bypassed with high-quality low-ESL/ESR capacitors.
power-supply decoupling
In order to properly decouple the supply planes from system noise, place as many capacitors (caps) as possible
close to the DSP. Assuming 0603 caps, the user should be able to fit a total of 60 caps, 30 for the core supply
and 30 for the I/O supply. These caps need to be close to the DSP power pins, no more than 1.25 cm maximum
distance to be effective. Physically smaller caps, such as 0402, are better because of their lower parasitic
inductance. Proper capacitance values are also important. Small bypass caps (near 560 pF) should be closest
to the power pins. Medium bypass caps (220 nF or as large as can be obtained in a small package) should be
next closest. TI recommends no less than 8 small and 8 medium caps per supply (32 total) be placed
immediately next to the BGA vias, using the “interior” BGA space and at least the corners of the “exterior”.
Eight larger caps (4 for each supply) can be placed further away for bulk decoupling. Large bulk caps (on the
order of 100 µF) should be furthest away (but still as close as possible). No less than 4 large caps per supply
(8 total) should be placed outside of the BGA.
Any cap selection needs to be evaluated from a yield/manufacturing point-of-view. As with the selection of any
component, verification of capacitor availability over the product’s production lifetime should be considered.

IEEE 1149.1 JTAG compatibility statement

The TMS320C6414T/15T/16T DSP requires that both TRST and RESET be asserted upon power up to be
properly initialized. While RESET initializes the DSP core, TRST initializes the DSP’s emulation logic. Both
resets are required for proper operation.
Note: TRST is synchronous and must be clocked by TCLK; otherwise, BSCAN may not respond as expected
after TRST is asserted.
While both TRST and RESET need to be asserted upon power up, only RESET needs to be released for the
DSP to boot properly. TRST may be asserted indefinitely for normal operation, keeping the JTAG port interface
and DSP’s emulation logic in the reset state. TRST only needs to be released when it is necessary to use a JTAG
controller to debug the DSP or exercise the DSP’s boundary scan functionality. RESET must be released only
in order for boundary-scan JTAG to read the variant field of IDCODE correctly. Other boundary-scan instructions
work correctly independant of current state of RESET.
For maximum reliability, the TMS320C6414T/15T/16T DSP includes an internal pulldown (IPD) on the TRST
pin to ensure that TRST will always be asserted upon power up and the DSP’s internal emulation logic will
always be properly initialized. JTAG controllers from Texas Instruments actively drive TRST high. However,
some third-party JTAG controllers may not drive TRST high but expect the use of a pullup resistor on TRST.
When using this type of JTAG controller, assert TRST to initialize the DSP after powerup and externally drive
TRST high before attempting any emulation or boundary scan operations.
Following the release of RESET, the low-to-high transition of TRST must be “seen” to latch the state of EMU1
and EMU0. The EMU[1:0] pins configure the device for either Boundary Scan mode or Emulation mode. For
more detailed information, see the terminal functions section of this data sheet.
Note: The DESIGN_WARNING section of the C6414T, C6415T, C6416T GLZ BSDL file contains information
and constraints regarding proper device operation while in Boundary Scan Mode.
For more detailed information on the C6414T/15T/16T JTAG emulation, see the TMS320C6000 DSP Designing
for JTAG Emulation Reference Guide (literature number SPRU641).
EMIF device speed

The rated EMIF speed, referring to both EMIFA and EMIFB, of these devices only applies to the SDRAM
interface when in a system that meets the following requirements:
− 1 chip-enable (CE) space (maximum of 2 chips) of SDRAM connected to EMIF
− up to 1 CE space of buffers connected to EMIF
− EMIF trace lengths between 1 and 3 inches
− 166-MHz SDRAM for 133-MHz operation (applies only to EMIFA)
− 143-MHz SDRAM for 100-MHz operation
Timing analysis must be done to verify all AC timings are met for all configurations. Verification of AC timings
is mandatory when using configurations other than those specified above. TI recommends utilizing I/O buffer
information specification (IBIS) to analyze all AC timings.
To properly use IBIS models to attain accurate timing analysis for a given system, see the Using IBIS Models
for Timing Analysis application report (literature number SPRA839).
To maintain signal integrity, serial termination resistors should be inserted into all EMIF output signal lines (see
the Terminal Functions table for the EMIF output signals).

bootmode
The C6414T/15T/16T device resets using the active-low signal RESET. While RESET is low, the device is held
in reset and is initialized to the prescribed reset state. Refer to reset timing for reset timing characteristics and
states of device pins during reset. The release of RESET starts the processor running with the prescribed device
configuration and boot mode.
The C6414T/C6415T/C6416T has three types of boot modes:
Host boot
If host boot is selected, upon release of RESET, the CPU is internally “stalled” while the remainder of the
device is released. During this period, an external host can initialize the CPU’s memory space as necessary
through the host interface, including internal configuration registers, such as those that control the EMIF or
other peripherals. For the C6414T device, the HPI peripheral is used for host boot. For the C6415T/C6416T
device, the HPI peripheral is used for host boot if PCI_EN = 0, and the PCI peripheral is used for host boot if
PCI_EN = 1. Once the host is finished with all necessary initialization, it must set the DSPINT bit in the HPIC
register to complete the boot process. This transition causes the boot configuration logic to bring the CPU
out of the “stalled” state. The CPU then begins execution from address 0. The DSPINT condition is not
latched by the CPU, because it occurs while the CPU is still internally “stalled”. Also, DSPINT brings the CPU
out of the “stalled” state only if the host boot process is selected. All memory may be written to and read by
the host. This allows for the host to verify what it sends to the DSP if required. After the CPU is out of the
“stalled” state, the CPU needs to clear the DSPINT, otherwise, no more DSPINTs can be received.
EMIF boot (using default ROM timings)
Upon the release of RESET, the 1K-Byte ROM code located in the beginning of CE1 is copied to address 0
by the EDMA using the default ROM timings, while the CPU is internally “stalled”. The data should be stored
in the endian format that the system is using. In this case, the EMIF automatically assembles consecutive
8-bit bytes to form the 32-bit instruction words to be copied. The transfer is automatically done by the EDMA
as a single-frame block transfer from the ROM to address 0. After completion of the block transfer, the CPU
is released from the “stalled” state and starts running from address 0.
No boot
With no boot, the CPU begins direct execution from the memory located at address 0. Note: operation is
undefined if invalid code is located at address 0.
reset
A hardware reset (RESET) is required to place the DSP into a known good state out of power-up. The RESET
signal can be asserted (pulled low) prior to ramping the core and I/O voltages or after the core and I/O voltages
have reached their proper operating conditions. As a best practice, reset should be held low during power-up.
Prior to deasserting RESET (low-to-high transition), the core and I/O voltages should be at their proper
operating conditions and CLKIN should also be running at the correct frequency.

absolute maximum ratings over operating case temperature range (unless otherwise noted)†
Supply voltage ranges: CVDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . − 0.5 V to 1.5 V
DVDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.4 V
Input voltage ranges: (except PCI), VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.4 V
(PCI), VIP [C6415T and C6416T only] . . . . . . . . . . . . . . . . . . −0.5 V to DVDD + 0.5 V
Output voltage ranges: (except PCI), VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.4 V
(PCI), VOP [C6415T and C6416T only] . . . . . . . . . . . . . . . . . −0.5 V to DVDD + 0.5 V
Operating case temperature ranges, TC: (default and M version) . . . . . . . . . . . . . . . . . . . . . . 0C to 90C
(A version) [A-600, A-720, A−850 only] . . . . . . . −40C to 105C
(D version) [D−1000 only] . . . . . . . . . . . . . . . . . . −40C to 90C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65C to 150C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to VSS.
recommended operating conditions

MIN NOM MAX UNIT
CVDD Supply voltage, Core (-600 devices)‡ 1.05 1.1 1.16 V
CVDD Supply voltage, Core (-720, -850, 1G devices)‡ 1.16 1.2 1.24 V
DVDD Supply voltage, I/O 3.14 3.3 3.46 V
VSS Supply ground 0 0 0 V
VIH High-level input voltage (except PCI) 2 V
VIL Low-level input voltage (except PCI) 0.8 V
VIP Input voltage (PCI) [C6415T and C6416T only] −0.5 DVDD + 0.5 V
VIHP High-level input voltage (PCI) [C6415T and C6416T only] 0.5DVDD DVDD + 0.5 V
VILP Low-level input voltage (PCI) [C6415T and C6416T only] −0.5 0.3DVDD V
VOS Maximum voltage during overshoot/undershoot (except PCI) −1.0§ 4.3§ V
Commercial temperature devices
0 90 C
[Blank, M−600, M−720, M−850, M−1000]
Extended temperature devices
TC Operating case temperature -40 105 C
[A−600, A−720, A−850 only]
Partial extended temperature devices
-40 90 C
[D−1000 only]
‡ Future variants of the C641xT DSPs may operate at voltages ranging from 1.0 V to 1.2 V to provide a range of system power/performance options.
TI highly recommends that users design-in a supply that can handle multiple voltages within this range (with ± 3% tolerances) by implementing
simple board changes such as reference resistor values or input pin configuration modifications. Examples of such supplies include the PT5406,
PT5815, PT6476, PT6505, and PT6719 series from Power Trends, a subsidiary of Texas Instruments. Not incorporating a flexible supply may
limit the system’s ability to easily adapt to future versions of C641xT devices.
§ The absolute maximum ratings should not be exceeded for more than 30% of the cycle period. This specification does not apply to PCI signals.

electrical characteristics over recommended ranges of supply voltage and operating case
temperature (unless otherwise noted)
PARAMETER TEST CONDITIONS† MIN TYP MAX UNIT
VOH High-level output voltage (except PCI) DVDD = MIN, IOH = MAX 2.4 V
High-level output voltage (PCI)
VOHP IOHP = −0.5 mA, DVDD = 3.3 V 0.9DVDD¶ V
[C6415T/C6416T only]
VOL Low-level output voltage (except PCI) DVDD = MIN, IOL = MAX 0.4 V
Low-level output voltage (PCI)
VOLP IOLP = 1.5 mA, DVDD = 3.3 V 0.1DVDD¶ V
VI = VSS to DVDD no opposing internal
±1 uA
resistor
VI = VSS to DVDD opposing internal
II Input current (except PCI) [DC] −200 −100 −50 uA
pullup resistor‡
VI = VSS to DVDD opposing internal
50 100 200 uA
pulldown resistor‡
Input leakage current (PCI) [DC]§
IIP 0 < VIP < DVDD = 3.3 V ±10 uA
EMIF, CLKOUT4, CLKOUT6, EMUx −8 mA
Timer, UTOPIA, TDO, GPIO (Excluding
IOH High-level output current [DC] −4 mA
GP[15:9, 2, 1]), McBSP
PCI/HPI −0.5¶ mA
EMIF, CLKOUT4, CLKOUT6, EMUx 8 mA
Timer, UTOPIA, TDO, GPIO (Excluding
IOL Low-level output current [DC] 4 mA
GP[15:9, 2, 1]), McBSP
PCI/HPI 1.5¶ mA
IOZ Off-state output current [DC] VO = DVDD or 0 V ±20 uA
ICDD Core supply current# CVDD = 1.2 V, CPU clock = 720 MHz 713 mA
ICDD Core supply current# CVDD = 1.2 V, CPU clock = 850 MHz 824 mA
CVDD = 1.2 V, CPU clock = 1 GHz 952 mA
ICDD Core supply current#
CVDD = 1.1 V, CPU clock = 600 MHz 558 mA
IDDD I/O supply current# DVDD = 3.3 V, CPU clock = 720 MHz 151 mA
Ci Input capacitance 2 pF
Co Output capacitance 3 pF
† For test conditions shown as MIN, MAX, or NOM, use the appropriate value specified in the recommended operating conditions table.
‡ Applies only to pins with an internal pullup (IPU) or pulldown (IPD) resistor.
§ PCI input leakage currents include Hi-Z output leakage for all bidirectional buffers with 3-state outputs.
¶ These rated numbers are from the PCI specification version 2.3. The DC specification and AC specification are defined in Tables 4-3 and 4-4,
respectively.
# Measured with average activity (50% high/50% low power). The actual current draw is highly application-dependent. For more details on core
and I/O activity, refer to the TMS320C6414T/15T/16T Power Consumption Application Report (literature number SPRAA45).
recommended clock and control signal transition behavior

All clocks and control signals must transition between VIH and VIL (or between VIL and VIH) in a monotonic
manner.

PARAMETER MEASUREMENT INFORMATION
Tester Pin Electronics Data Sheet Timing Reference Point
42 W 3.5 nH Output
Transmission Line Under
Test
Z0 = 50 W
(see note) Device Pin
4.0 pF 1.85 pF (see note)
NOTE: The data sheet provides timing at the device pin. For output timing analysis, the tester pin electronics and its transmission line effects
must be taken into account. A transmission line with a delay of 2 ns or longer can be used to produce the desired transmission line effect.
The transmission line is intended as a load only. It is not necessary to add or subtract the transmission line delay (2 ns or longer) from
the data sheet timings.
Input requirements in this data sheet are tested with an input slew rate of < 4 Volts per nanosecond (4 V/ns) at the device pin.
Figure 12. Test Load Circuit for AC Timing Measurements
The tester load circuit is for characterization and measurement of AC timing signals. This load does not indicate
the maximum load the device is capable of driving.
signal transition levels

All input and output timing parameters are referenced to 1.5 V for both “0” and “1” logic levels.
Vref = 1.5 V
Figure 13. Input and Output Voltage Reference Levels for AC Timing Measurements
All rise and fall transition timing parameters are referenced to VIL MAX and VIH MIN for input clocks, VOL MAX
and VOH MIN for output clocks, VILP MAX and VIHP MIN for PCI input clocks, and VOLP MAX and VOHP MIN for
PCI output clocks.
Vref = VIH MIN (or VOH MIN or
VIHP MIN or VOHP MIN)
Vref = VIL MAX (or VOL MAX or

VILP MAX or VOLP MAX)
Figure 14. Rise and Fall Transition Time Voltage Reference Levels
signal transition rates

All timings are tested with an input edge rate of 4 Volts per nanosecond (4 V/ns).

PARAMETER MEASUREMENT INFORMATION (CONTINUED)

timing parameters and board routing analysis
The timing parameter values specified in this data sheet do not include delays by board routings. As a good
board design practice, such delays must always be taken into account. Timing values may be adjusted by
increasing/decreasing such delays. TI recommends utilizing the available I/O buffer information specification
(IBIS) models to analyze the timing characteristics correctly. To properly use IBIS models to attain accurate
timing analysis for a given system, see the Using IBIS Models for Timing Analysis application report (literature
number SPRA839). If needed, external logic hardware such as buffers may be used to compensate any timing
differences.
For inputs, timing is most impacted by the round-trip propagation delay from the DSP to the external device and
from the external device to the DSP. This round-trip delay tends to negatively impact the input setup time margin,
but also tends to improve the input hold time margins (see Table 33 and Figure 15).
Figure 15 represents a general transfer between the DSP and an external device. The figure also represents
board route delays and how they are perceived by the DSP and the external device.
Table 33. Board-Level Parameters Example (see Figure 15)
NO. DESCRIPTION
1 Clock route delay
2 Minimum DSP hold time
3 Minimum DSP setup time
4 External device hold time requirement
5 External device setup time requirement
6 Control signal route delay
7 External device hold time
8 External device access time
9 DSP hold time requirement
10 DSP setup time requirement
11 Data route delay
ECLKOUTx
(Output from DSP)
1
ECLKOUTx
(Input to External Device)
2
3
Control Signals†
(Output from DSP)
4
5
Control Signals 6
(Input to External Device)
7
8
Data Signals‡
(Output from External Device)
9
10
11
Data Signals‡
(Input to DSP)
† Control signals include data for Writes.

‡ Data signals are generated during Reads from an external device.
Figure 15. Board-Level Input/Output Timings

INPUT AND OUTPUT CLOCKS

timing requirements for CLKIN for -600 devices†‡§ (see Figure 16)
−600
NO. PLL MODE x20 PLL MODE x12 PLL MODE x6 x1 (BYPASS) UNIT
MIN MAX MIN MAX MIN MAX MIN MAX
1 tc(CLKIN) Cycle time, CLKIN 33.3 40 20 23.8 13.3 23.8 0 10 ns
2 tw(CLKINH) Pulse duration, CLKIN high 0.4C 0.4C 0.4C 0.45C ns
3 tw(CLKINL) Pulse duration, CLKIN low 0.4C 0.4C 0.4C 0.45C ns
4 tt(CLKIN) Transition time, CLKIN 5 5 5 1 ns
5 tJ(CLKIN) Period jitter, CLKIN 0.02C 0.02C 0.02C 0.02C ns
† The reference points for the rise and fall transitions are measured at VIL MAX and VIH MIN.
‡ For more details on the PLL multiplier factors (x6, x12, x20), see the Clock PLL section of this data sheet.
§ C = CLKIN cycle time in ns. For example, when CLKIN frequency is 50 MHz, use C = 20 ns.
−720
1 tc(CLKIN) Cycle time, CLKIN 27.7 40 16.6 23.8 13.3 23.8 0 10 ns

−850
1 tc(CLKIN) Cycle time, CLKIN 23.5 40 14 23.8 13.3 23.8 0 10 ns
timing requirements for CLKIN for -1G devices†‡§ (see Figure 16)
−1G
1 tc(CLKIN) Cycle time, CLKIN 20 40 13.3 23.8 13.3 23.8 0 10 ns
5 1
4
2
CLKIN
3
4
Figure 16. CLKIN Timing

INPUT AND OUTPUT CLOCKS (CONTINUED)

switching characteristics over recommended operating conditions for CLKOUT4†‡§
(see Figure 17)
−600, −720
−850, −1G
NO. PARAMETER CLKMODE = x1, x6, UNIT
x12, x20
MIN MAX
1 tJ(CKO4) Period jitter, CLKOUT4 0 ±175 ps
2 tw(CKO4H) Pulse duration, CLKOUT4 high 2P − 0.7 2P + 0.7 ns
3 tw(CKO4L) Pulse duration, CLKOUT4 low 2P − 0.7 2P + 0.7 ns
4 tt(CKO4) Transition time, CLKOUT4 1 ns
† The reference points for the rise and fall transitions are measured at VOL MAX and VOH MIN.
‡ PH is the high period of CLKIN in ns and PL is the low period of CLKIN in ns.
§ P = 1/CPU clock frequency in nanoseconds (ns)
1 4
2
CLKOUT4
3
4
Figure 17. CLKOUT4 Timing
switching characteristics over recommended operating conditions for CLKOUT6†‡§

(see Figure 18)
−600, −720
−850, −1G
NO. PARAMETER CLKMODE = x1, x6, UNIT
x12, x20
MIN MAX
1 tJ(CKO6) Period jitter, CLKOUT6 0 ±175 ps
2 tw(CKO6H) Pulse duration, CLKOUT6 high 3P − 0.7 3P + 0.7 ns
3 tw(CKO6L) Pulse duration, CLKOUT6 low 3P − 0.7 3P + 0.7 ns
4 tt(CKO6) Transition time, CLKOUT6 1 ns
‡ PH is the high period of CLKIN in ns and PL is the low period of CLKIN in ns.
§ P = 1/CPU clock frequency in nanoseconds (ns)
1
4
2
CLKOUT6
3
4
Figure 18. CLKOUT6 Timing

timing requirements for ECLKIN for EMIFA and EMIFB†‡§¶ (see Figure 19)
−600
−720
NO. −850 UNIT
−1G
MIN MAX
CVDD = 1.2 V 6# 16P ns
1 tc(EKI) Cycle time, ECLKIN
CVDD = 1.1 V 7.5# 16P ns
2 tw(EKIH) Pulse duration, ECLKIN high 2.7 ns
3 tw(EKIL) Pulse duration, ECLKIN low 2.7 ns
4 tt(EKI) Transition time, ECLKIN 2 ns
5 tJ(EKI) Period jitter, ECLKIN 0.02E ns
† P = 1/CPU clock frequency in ns. For example, when running parts at 720 MHz, use P = 1.39 ns.
‡ The reference points for the rise and fall transitions are measured at VIL MAX and VIH MIN.
§ These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are
prefixed by a “B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted.
¶ E = the EMIF input clock (ECLKIN, CPU/4 clock, or CPU/6 clock) period in ns for EMIFA or EMIFB.
# Minimum ECLKIN cycle times must be met, even when ECLKIN is generated by an internal clock source. Minimum ECLKIN times are based
on internal logic speed; the maximum useable speed of the EMIF may be lower due to AC timing requirements. On the devices, 133-MHz
operation is achievable if the requirements of the EMIF Device Speed section are met.
5 1
4
2
ECLKIN
3
4
Figure 19. ECLKIN Timing for EMIFA and EMIFB
switching characteristics over recommended operating conditions for ECLKOUT1 for EMIFA and
EMIFB modules§¶|| (see Figure 20)
−600
−720
NO. PARAMETER −850 UNIT
−1G
MIN MAX
1 tJ(EKO1) Period jitter, ECLKOUT1 0 ±175 ps
2 tw(EKO1H) Pulse duration, ECLKOUT1 high EH − 0.7 EH + 0.7 ns
3 tw(EKO1L) Pulse duration, ECLKOUT1 low EL − 0.7 EL + 0.7 ns
4 tt(EKO1) Transition time, ECLKOUT1 1 ns
5 td(EKIH-EKO1H) Delay time, ECLKIN high to ECLKOUT1 high 0.8 8 ns
6 td(EKIL-EKO1L) Delay time, ECLKIN low to ECLKOUT1 low 0.8 8 ns
§ These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are
¶ E = the EMIF input clock (ECLKIN, CPU/4 clock, or CPU/6 clock) period in ns for EMIFA or EMIFB.
|| The reference points for the rise and fall transitions are measured at VOL MAX and VOH MIN.
EH is the high period of E (EMIF input clock period) in ns and EL is the low period of E (EMIF input clock period) in ns for EMIFA or EMIFB.
This cycle-to-cycle jitter specification was measured with CPU/4 or CPU/6 as the source of the EMIF input clock.

ECLKIN
1
6 3
5 2 4 4
ECLKOUT1
Figure 20. ECLKOUT1 Timing for EMIFA and EMIFB Modules
switching characteristics over recommended operating conditions for ECLKOUT2 for the EMIFA
and EMIFB modules†‡§ (see Figure 21)
−600
−720
−1G
MIN MAX
1 tJ(EKO2) Period jitter, ECLKOUT2 0 ±175¶ ps
2 tw(EKO2H) Pulse duration, ECLKOUT2 high 0.5NE − 0.7 0.5NE + 0.7 ns
3 tw(EKO2L) Pulse duration, ECLKOUT2 low 0.5NE − 0.7 0.5NE + 0.7 ns
4 tt(EKO2) Transition time, ECLKOUT2 1 ns
5 td(EKIH-EKO2H) Delay time, ECLKIN high to ECLKOUT2 high 3 8 ns
6 td(EKIH-EKO2L) Delay time, ECLKIN high to ECLKOUT2 low 3 8 ns
‡ These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are
§ E = the EMIF input clock (ECLKIN, CPU/4 clock, or CPU/6 clock) period in ns for EMIFA or EMIFB.
N = the EMIF input clock divider; N = 1, 2, or 4.
¶ This cycle-to-cycle jitter specification was measured with CPU/4 or CPU/6 as the source of the EMIF input clock.
5 6
ECLKIN
1 3
2 4 4
ECLKOUT2
Figure 21. ECLKOUT2 Timing for the EMIFA and EMIFB Modules

ASYNCHRONOUS MEMORY TIMING
timing requirements for asynchronous memory cycles for EMIFA module†‡§

(see Figure 22 and Figure 23)
−600
−720
NO. −850 UNIT
−1G
MIN MAX
3 tsu(EDV-AREH) Setup time, EDx valid before ARE high 6.5 ns
4 th(AREH-EDV) Hold time, EDx valid after ARE high 1 ns
6 tsu(ARDY-EKO1H) Setup time, ARDY valid before ECLKOUTx high 3 ns
7 th(EKO1H-ARDY) Hold time, ARDY valid after ECLKOUTx high 1 ns
† To ensure data setup time, simply program the strobe width wide enough. ARDY is internally synchronized. The ARDY signal is only recognized
two cycles before the end of the programmed strobe time and while ARDY is low, the strobe time is extended cycle-by-cycle. When ARDY is
recognized low, the end of the strobe time is two cycles after ARDY is recognized high. To use ARDY as an asynchronous input, the pulse width
of the ARDY signal should be wide enough (e.g., pulse width = 2E) to ensure setup and hold time is met.
‡ RS = Read setup, RST = Read strobe, RH = Read hold, WS = Write setup, WST = Write strobe, WH = Write hold. These parameters are
programmed via the EMIF CE space control registers.
§ These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the asynchronous
memory access signals are shown as generic (AOE, ARE, and AWE) instead of AAOE, AARE, and AAWE (for EMIFA) and BAOE, BARE, and
BAWE (for EMIFB)].
switching characteristics over recommended operating conditions for asynchronous memory

cycles for EMIFA module‡§¶# (see Figure 22 and Figure 23)
−600
−720
−1G
MIN MAX
1 tosu(SELV-AREL) Output setup time, select signals valid to ARE low RS * E − 1.5 ns
2 toh(AREH-SELIV) Output hold time, ARE high to select signals invalid RH * E − 1.9 ns
5 td(EKO1H-AREV) Delay time, ECLKOUTx high to ARE valid 1 7 ns
8 tosu(SELV-AWEL) Output setup time, select signals valid to AWE low WS * E − 1.7 ns
9 toh(AWEH-SELIV) Output hold time, AWE high to select signals invalid WH * E − 1.8 ns
10 td(EKO1H-AWEV) Delay time, ECLKOUTx high to AWE valid 1.3 7.1 ns
BAWE (for EMIFB)].
¶ E = ECLKOUT1 period in ns for EMIFA or EMIFB
# Select signals for EMIFA include: ACEx, ABE[7:0], AEA[22:3], AAOE; and for EMIFA writes, include AED[63:0].
Select signals EMIFB include: BCEx, BBE[1:0], BEA[20:1], BAOE; and for EMIFB writes, include BED[15:0].

ASYNCHRONOUS MEMORY TIMING (CONTINUED)
timing requirements for asynchronous memory cycles for EMIFB module†‡§

(see Figure 22 and Figure 23)
−600
−720
NO. −850 UNIT
−1G
MIN MAX
3 tsu(EDV-AREH) Setup time, EDx valid before ARE high 6.2 ns
4 th(AREH-EDV) Hold time, EDx valid after ARE high 1 ns
6 tsu(ARDY-EKO1H) Setup time, ARDY valid before ECLKOUTx high 3 ns
7 th(EKO1H-ARDY) Hold time, ARDY valid after ECLKOUTx high 1.2 ns
† To ensure data setup time, simply program the strobe width wide enough. ARDY is internally synchronized. The ARDY signal is only recognized
two cycles before the end of the programmed strobe time and while ARDY is low, the strobe time is extended cycle-by-cycle. When ARDY is
recognized low, the end of the strobe time is two cycles after ARDY is recognized high. To use ARDY as an asynchronous input, the pulse width
of the ARDY signal should be wide enough (e.g., pulse width = 2E) to ensure setup and hold time is met.
BAWE (for EMIFB)].
switching characteristics over recommended operating conditions for asynchronous memory

cycles for EMIFB module‡§¶# (see Figure 22 and Figure 23)
−600
−720
−1G
MIN MAX
1 tosu(SELV-AREL) Output setup time, select signals valid to ARE low RS * E − 1.6 ns
2 toh(AREH-SELIV) Output hold time, ARE high to select signals invalid RH * E − 1.7 ns
5 td(EKO1H-AREV) Delay time, ECLKOUTx high to ARE valid 0.8 6.6 ns
8 tosu(SELV-AWEL) Output setup time, select signals valid to AWE low WS * E − 1.9 ns
9 toh(AWEH-SELIV) Output hold time, AWE high to select signals invalid WH * E − 1.7 ns
10 td(EKO1H-AWEV) Delay time, ECLKOUTx high to AWE vaild 0.9 6.7 ns
BAWE (for EMIFB)].
¶ E = ECLKOUT1 period in ns for EMIFA or EMIFB
# Select signals for EMIFA include: ACEx, ABE[7:0], AEA[22:3], AAOE; and for EMIFA writes, include AED[63:0].
Select signals EMIFB include: BCEx, BBE[1:0], BEA[20:1], BAOE; and for EMIFB writes, include BED[15:0].


Setup = 2 Strobe = 3 Not Ready Hold = 2
ECLKOUTx
1 2
CEx
1 2
ABE[7:0] or BBE[1:0] BE
1 2
AEA[22:3] or BEA[20:1] Address
3
4
AED[63:0] or BED[15:0]
1 2
Read Data
AOE/SDRAS/SOE‡
5 5
ARE/SDCAS/SADS/SRE‡
AWE/SDWE/SWE‡ 7
7
6 6
ARDY
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
BAWE (for EMIFB)].
‡ AOE/SDRAS/SOE, ARE/SDCAS/SADS/SRE, and AWE/SDWE/SWE operate as AOE (identified under select signals), ARE, and AWE,
respectively, during asynchronous memory accesses.
Figure 22. Asynchronous Memory Read Timing for EMIFA and EMIFB†


Setup = 2 Strobe = 3 Not Ready Hold = 2
ECLKOUTx
8 9
CEx
9
8
ABE[7:0] or BBE[1:0] BE
8 9
AEA[22:3] or BEA[20:1] Address
8 9
AED[63:0] or BED[15:0] Write Data
AOE/SDRAS/SOE‡
10
10
AWE/SDWE/SWE‡
7 7
6 6
ARDY
BAWE (for EMIFB)].
‡ AOE/SDRAS/SOE, ARE/SDCAS/SADS/SRE, and AWE/SDWE/SWE operate as AOE (identified under select signals), ARE, and AWE,
respectively, during asynchronous memory accesses.
Figure 23. Asynchronous Memory Write Timing for EMIFA and EMIFB†

PROGRAMMABLE SYNCHRONOUS INTERFACE TIMING
timing requirements for programmable synchronous interface cycles for EMIFA module†
(see Figure 24)
−600
−720
NO. −850 UNIT
−1G
MIN MAX
6 tsu(EDV-EKOxH) Setup time, read EDx valid before ECLKOUTx high 2 ns
7 th(EKOxH-EDV) Hold time, read EDx valid after ECLKOUTx high 1.5 ns
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the programmable
synchronous interface access signals are shown as generic (SADS/SRE, SOE, and SWE) instead of ASADS/ASRE, ASOE, and ASWE (for
EMIFA) and BSADS/BSRE, BSOE, and BSWE (for EMIFB)].
switching characteristics over recommended operating conditions for programmable

synchronous interface cycles for EMIFA module†‡ (see Figure 24−Figure 26)
−600
−720
−1G
MIN MAX
1 td(EKOxH-CEV) Delay time, ECLKOUTx high to CEx valid 1.3 4.9 ns
2 td(EKOxH-BEV) Delay time, ECLKOUTx high to BEx valid 4.9 ns
3 td(EKOxH-BEIV) Delay time, ECLKOUTx high to BEx invalid 1.3 ns
4 td(EKOxH-EAV) Delay time, ECLKOUTx high to EAx valid 4.9 ns
5 td(EKOxH-EAIV) Delay time, ECLKOUTx high to EAx invalid 1.3 ns
8 td(EKOxH-ADSV) Delay time, ECLKOUTx high to SADS/SRE valid 1.3 4.9 ns
9 td(EKOxH-OEV) Delay time, ECLKOUTx high to, SOE valid 1.3 4.9 ns
10 td(EKOxH-EDV) Delay time, ECLKOUTx high to EDx valid 4.9 ns
11 td(EKOxH-EDIV) Delay time, ECLKOUTx high to EDx invalid 1.3 ns
12 td(EKOxH-WEV) Delay time, ECLKOUTx high to SWE valid 1.3 4.9 ns
‡ The following parameters are programmable via the EMIF CE Space Secondary Control register (CExSEC):
− Read latency (SYNCRL): 0-, 1-, 2-, or 3-cycle read latency
− Write latency (SYNCWL): 0-, 1-, 2-, or 3-cycle write latency
− CEx assertion length (CEEXT): For standard SBSRAM or ZBT SRAM interface, CEx goes inactive after the final command has been issued
(CEEXT = 0). For synchronous FIFO interface with glue, CEx is active when SOE is active (CEEXT = 1).
− Function of SADS/SRE (RENEN): For standard SBSRAM or ZBT SRAM interface, SADS/SRE acts as SADS with deselect cycles
(RENEN = 0). For FIFO interface, SADS/SRE acts as SRE with NO deselect cycles (RENEN = 1).
− Synchronization clock (SNCCLK): Synchronized to ECLKOUT1 or ECLKOUT2

PROGRAMMABLE SYNCHRONOUS INTERFACE TIMING (CONTINUED)
timing requirements for programmable synchronous interface cycles for EMIFB module†
(see Figure 24)
−600
−720
NO. −850 UNIT
−1G
MIN MAX
6 tsu(EDV-EKOxH) Setup time, read EDx valid before ECLKOUTx high 3.1 ns
7 th(EKOxH-EDV) Hold time, read EDx valid after ECLKOUTx high 1.5 ns
switching characteristics over recommended operating conditions for programmable

synchronous interface cycles for EMIFB module†‡ (see Figure 24−Figure 26)
−600
−720
−1G
MIN MAX
1 td(EKOxH-CEV) Delay time, ECLKOUTx high to CEx valid 1.3 6.4 ns
2 td(EKOxH-BEV) Delay time, ECLKOUTx high to BEx valid 6.4 ns
3 td(EKOxH-BEIV) Delay time, ECLKOUTx high to BEx invalid 1.3 ns
4 td(EKOxH-EAV) Delay time, ECLKOUTx high to EAx valid 6.4 ns
5 td(EKOxH-EAIV) Delay time, ECLKOUTx high to EAx invalid 1.3 ns
8 td(EKOxH-ADSV) Delay time, ECLKOUTx high to SADS/SRE valid 1.3 6.4 ns
9 td(EKOxH-OEV) Delay time, ECLKOUTx high to, SOE valid 1.3 6.4 ns
10 td(EKOxH-EDV) Delay time, ECLKOUTx high to EDx valid 6.4 ns
11 td(EKOxH-EDIV) Delay time, ECLKOUTx high to EDx invalid 1.3 ns
12 td(EKOxH-WEV) Delay time, ECLKOUTx high to SWE valid 1.3 6.4 ns
‡ The following parameters are programmable via the EMIF CE Space Secondary Control register (CExSEC):

READ latency = 2
ECLKOUTx
1 1
CEx
2 3
ABE[7:0] or BBE[1:0] BE1 BE2 BE3 BE4
4 5
AEA[22:3] or BEA[20:1] EA1 EA2 EA3 EA4
6
7
AED[63:0] or BED[15:0] Q1 Q2 Q3 Q4
8 8
ARE/SDCAS/SADS/SRE§
9 9
AOE/SDRAS/SOE§
AWE/SDWE/SWE§
‡ The read latency and the length of CEx assertion are programmable via the SYNCRL and CEEXT fields, respectively, in the EMIFx CE Space
Secondary Control register (CExSEC). In this figure, SYNCRL = 2 and CEEXT = 0.
§ The following parameters are programmable via the EMIF CE Space Secondary Control register (CExSEC):
¶ ARE/SDCAS/SADS/SRE, AOE/SDRAS/SOE, and AWE/SDWE/SWE operate as SADS/SRE, SOE, and SWE, respectively, during
programmable synchronous interface accesses.
Figure 24. Programmable Synchronous Interface Read Timing for EMIFA and EMIFB
(With Read Latency = 2)†‡§

ECLKOUTx
1 1
CEx
2 3
4 5
10
10 11
AED[63:0] or BED[15:0] Q1 Q2 Q3 Q4
8 8
ARE/SDCAS/SADS/SRE¶
AOE/SDRAS/SOE¶
12 12
AWE/SDWE/SWE¶
‡ The write latency and the length of CEx assertion are programmable via the SYNCWL and CEEXT fields, respectively, in the EMIFx CE Space
Secondary Control register (CExSEC). In this figure, SYNCWL = 0 and CEEXT = 0.
Figure 25. Programmable Synchronous Interface Write Timing for EMIFA and EMIFB
(With Write Latency = 0)†‡§

Write
Latency =
1‡
ECLKOUTx
1 1
CEx
2 3
4 5
10 10 11
AED[63:0] or BED[15:0] Q1 Q2 Q3 Q4
8 8
ARE/SDCAS/SADS/SRE¶
AOE/SDRAS/SOE¶
12 12
AWE/SDWE/SWE¶
‡ The write latency and the length of CEx assertion are programmable via the SYNCWL and CEEXT fields, respectively, in the EMIFx CE Space
Secondary Control register (CExSEC). In this figure, SYNCWL = 1 and CEEXT = 0.
Figure 26. Programmable Synchronous Interface Write Timing for EMIFA and EMIFB
(With Write Latency = 1)†‡§

SYNCHRONOUS DRAM TIMING
timing requirements for synchronous DRAM cycles for EMIFA module† (see Figure 27)
−600
−720
NO. −850 UNIT
−1G
MIN MAX
6 tsu(EDV-EKO1H) Setup time, read EDx valid before ECLKOUTx high 0.6 ns
CVDD = 1.2 V 1.8 ns
7 th(EKO1H-EDV) Hold time, read EDx valid after ECLKOUTx high
CVDD = 1.1 V 2.0 ns
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the synchronous DRAM
memory access signals are shown as generic ( SDCAS, SDWE, and SDRAS ) instead of ASDCAS, ASDWE, and ASDRAS (for EMIFA) and
BSDCAS, BSDWE, and BSDRAS (for EMIFB)].
switching characteristics over recommended operating conditions for synchronous DRAM cycles
for EMIFA module† (see Figure 27−Figure 34)
−600
−720
−1G
MIN MAX
1 td(EKO1H-CEV) Delay time, ECLKOUTx high to CEx valid 1.3 4.9 ns
2 td(EKO1H-BEV) Delay time, ECLKOUTx high to BEx valid 4.9 ns
3 td(EKO1H-BEIV) Delay time, ECLKOUTx high to BEx invalid 1.3 ns
4 td(EKO1H-EAV) Delay time, ECLKOUTx high to EAx valid 4.9 ns
5 td(EKO1H-EAIV) Delay time, ECLKOUTx high to EAx invalid 1.3 ns
8 td(EKO1H-CASV) Delay time, ECLKOUTx high to SDCAS valid 1.3 4.9 ns
9 td(EKO1H-EDV) Delay time, ECLKOUTx high to EDx valid 4.9 ns
10 td(EKO1H-EDIV) Delay time, ECLKOUTx high to EDx invalid 1.3 ns
11 td(EKO1H-WEV) Delay time, ECLKOUTx high to SDWE valid 1.3 4.9 ns
12 td(EKO1H-RAS) Delay time, ECLKOUTx high to SDRAS valid 1.3 4.9 ns
13 td(EKO1H-ACKEV) Delay time, ECLKOUTx high to ASDCKE valid (EMIFA only) 1.3 4.9 ns
14 td(EKO1H-PDTV) Delay time, ECLKOUTx high to PDT valid 1.3 4.9 ns

SYNCHRONOUS DRAM TIMING (CONTINUED)
timing requirements for synchronous DRAM cycles for EMIFB module† (see Figure 27)
−600
−720
NO. −850 UNIT
−1G
MIN MAX
6 tsu(EDV-EKO1H) Setup time, read EDx valid before ECLKOUTx high 2.1 ns
7 th(EKO1H-EDV) Hold time, read EDx valid after ECLKOUTx high 2.5 ns
switching characteristics over recommended operating conditions for synchronous DRAM cycles
for EMIFB module† (see Figure 27−Figure 34)
−600
−720
−1G
MIN MAX
1 td(EKO1H-CEV) Delay time, ECLKOUTx high to CEx valid 1.3 6.4 ns
2 td(EKO1H-BEV) Delay time, ECLKOUTx high to BEx valid 6.4 ns
3 td(EKO1H-BEIV) Delay time, ECLKOUTx high to BEx invalid 1.3 ns
4 td(EKO1H-EAV) Delay time, ECLKOUTx high to EAx valid 6.4 ns
5 td(EKO1H-EAIV) Delay time, ECLKOUTx high to EAx invalid 1.3 ns
8 td(EKO1H-CASV) Delay time, ECLKOUTx high to SDCAS valid 1.3 6.4 ns
9 td(EKO1H-EDV) Delay time, ECLKOUTx high to EDx valid 6.4 ns
10 td(EKO1H-EDIV) Delay time, ECLKOUTx high to EDx invalid 1.3 ns
11 td(EKO1H-WEV) Delay time, ECLKOUTx high to SDWE valid 1.3 6.4 ns
12 td(EKO1H-RAS) Delay time, ECLKOUTx high to SDRAS valid 1.3 6.4 ns
13 td(EKO1H-ACKEV) Delay time, ECLKOUTx high to ASDCKE valid (EMIFA only) 1.3 6.4 ns
14 td(EKO1H-PDTV) Delay time, ECLKOUTx high to PDT valid 1.3 6.4 ns

READ
ECLKOUTx
1 1
CEx
2 3
4 5
AEA[22:14] or BEA[20:12] Bank
4 5
AEA[12:3] or BEA[10:1] Column
4 5
AEA13 or BEA11
6
7
AED[63:0] or BED[15:0] D1 D2 D3 D4
AOE/SDRAS/SOE‡
8 8
AWE/SDWE/SWE‡
14 14
PDT§
‡ ARE/SDCAS/SADS/SRE, AWE/SDWE/SWE, and AOE/SDRAS/SOE operate as SDCAS, SDWE, and SDRAS, respectively, during SDRAM
accesses.
§ PDT signal is only asserted when the EDMA is in PDT mode (set the PDTS bit to 1 in the EDMA options parameter RAM). For PDT read, data
is not latched into EMIF. The PDTRL field in the PDT control register (PDTCTL) configures the latency of the PDT signal with respect to the data
phase of a read transaction. The latency of the PDT signal for a read can be programmed to 0, 1, 2, or 3 by setting PDTRL to 00, 01, 10, or 11,
respectively. PDTRL equals 00 (zero latency) in Figure 27.
Figure 27. SDRAM Read Command (CAS Latency 3) for EMIFA and EMIFB†

WRITE
ECLKOUTx
1 2
CEx
2 4 3
4 5
4 5
AEA[12:3] or BEA[10:1] Column
4 5
AEA13 or BEA11
9 9 10
AED[63:0] or BED[15:0] D1 D2 D3 D4
AOE/SDRAS/SOE‡
8 8
11 11
AWE/SDWE/SWE‡
14 14
PDT§
accesses.
§ PDT signal is only asserted when the EDMA is in PDT mode (set the PDTD bit to 1 in the EDMA options parameter RAM). For PDT write, data
is not driven (in High-Z). The PDTWL field in the PDT control register (PDTCTL) configures the latency of the PDT signal with respect to the data
phase of a write transaction. The latency of the PDT signal for a write transaction can be programmed to 0, 1, 2, or 3 by setting PDTWL to 00,
01, 10, or 11, respectively. PDTWL equals 00 (zero latency) in Figure 28.
Figure 28. SDRAM Write Command for EMIFA and EMIFB†

ACTV
ECLKOUTx
1 1
CEx
ABE[7:0] or BBE[1:0]
4 5
AEA[22:14] or BEA[20:12] Bank Activate
4 5
AEA[12:3] or BEA[10:1] Row Address
4 5
AEA13 or BEA11 Row Address
AED[63:0] or BED[15:0]
12 12
AOE/SDRAS/SOE‡
AWE/SDWE/SWE‡
accesses.
Figure 29. SDRAM ACTV Command for EMIFA and EMFB†

DCAB
ECLKOUTx
1 1
CEx
AEA[22:14, 12:3] or
BEA[20:12, 10:1]
4 5
AEA13 or BEA11
AED[63:0] or BED[15:0]
12 12
AOE/SDRAS/SOE‡
11 11
AWE/SDWE/SWE‡
accesses.
Figure 30. SDRAM DCAB Command for EMIFA and EMIFB†

DEAC
ECLKOUTx
1 1
CEx
4 5
AEA[12:3] or BEA[10:1]
4 5
AEA13 or BEA11
AED[63:0] or BED[15:0]
12 12
AOE/SDRAS/SOE‡
11 11
AWE/SDWE/SWE‡
accesses.
Figure 31. SDRAM DEAC Command for EMIFA and EMIFB†

REFR
ECLKOUTx
1 1
CEx
AEA[22:14, 12:3] or
BEA[20:12, 10:1]
AEA13 or BEA11
AED[63:0] or BED[15:0]
12 12
AOE/SDRAS/SOE‡
8 8
AWE/SDWE/SWE‡
accesses.
Figure 32. SDRAM REFR Command for EMIFA and EMIFB†

MRS
ECLKOUTx
1 1
CEx
4 5
AEA[22:3] or BEA[20:1] MRS value
AED[63:0] or BED[15:0]
12 12
AOE/SDRAS/SOE‡
8 8
11 11
AWE/SDWE/SWE‡
accesses.
Figure 33. SDRAM MRS Command for EMIFA and EMIFB†

≥ TRAS cycles
Self Refresh End Self-Refresh
AECLKOUTx
ACEx
ABE[7:0]
AEA[22:14, 12:3]
AEA13
AED[63:0]
AAOE/ASDRAS/ASOE‡
AARE/ASDCAS/ASADS/
ASRE‡
AAWE/ASDWE/ASWE‡
13 13
ASDCKE
‡ AARE/ASDCAS/ASADS/ASRE, AAWE/ASDWE/ASWE, and AAOE/ASDRAS/ASOE operate as ASDCAS, ASDWE, and ASDRAS,
respectively, during SDRAM accesses.
Figure 34. SDRAM Self-Refresh Timing for EMIFA Only†

HOLD/HOLDA TIMING
timing requirements for the HOLD/HOLDA cycles for EMIFA and EMIFB modules† (see Figure 35)
−600, −720
NO. −850, −1G UNIT
MIN MAX
3 th(HOLDAL-HOLDL) Hold time, HOLD low after HOLDA low E ns
† E = the EMIF input clock (ECLKIN, CPU/4 clock, or CPU/6 clock) period in ns for EMIFA or EMIFB.
switching characteristics over recommended operating conditions for the HOLD/HOLDA cycles
for EMIFA and EMIFB modules†‡§ (see Figure 35)
−600, −720
NO. PARAMETER −850, −1G UNIT
MIN MAX
1 td(HOLDL-EMHZ) Delay time, HOLD low to EMIF Bus high impedance 2E ¶ ns
2 td(EMHZ-HOLDAL) Delay time, EMIF Bus high impedance to HOLDA low 0 2E ns
4 td(HOLDH-EMLZ) Delay time, HOLD high to EMIF Bus low impedance 2E 7E ns
5 td(EMLZ-HOLDAH) Delay time, EMIF Bus low impedance to HOLDA high 0 2E ns
6 td(HOLDL-EKOHZ) Delay time, HOLD low to ECLKOUTx high impedance 2E ¶ ns
7 td(HOLDH-EKOLZ) Delay time, HOLD high to ECLKOUTx low impedance 2E 7E ns
† E = the EMIF input clock (ECLKIN, CPU/4 clock, or CPU/6 clock) period in ns for EMIFA or EMIFB.
‡ For EMIFA, EMIF Bus consists of: ACE[3:0], ABE[7:0], AED[63:0], AEA[22:3], AARE/ASDCAS/ASADS/ASRE, AAOE/ASDRAS/ASOE, and
AAWE/ASDWE/ASWE , ASDCKE, ASOE3, and APDT.
For EMIFB, EMIF Bus consists of: BCE[3:0], BBE[1:0], BED[15:0], BEA[20:1], BARE/BSDCAS/BSADS/BSRE, BAOE/BSDRAS/BSOE, and
BAWE/BSDWE/BSWE, BSOE3, and BPDT.
§ The EKxHZ bits in the EMIF Global Control register (GBLCTL) determine the state of the ECLKOUTx signals during HOLDA. If EKxHZ = 0,
ECLKOUTx continues clocking during Hold mode. If EKxHZ = 1, ECLKOUTx goes to high impedance during Hold mode, as shown in Figure 35.
¶ All pending EMIF transactions are allowed to complete before HOLDA is asserted. If no bus transactions are occurring, then the minimum delay
time can be achieved. Also, bus hold can be indefinitely delayed by setting NOHOLD = 1.
External Requestor
DSP Owns Bus DSP Owns Bus
Owns Bus
3
HOLD
2 5
HOLDA
1 4
EMIF Bus† C64x C64x
ECLKOUTx‡
(EKxHZ = 0)
6 7
ECLKOUTx‡
(EKxHZ = 1)
† For EMIFA, EMIF Bus consists of: ACE[3:0], ABE[7:0], AED[63:0], AEA[22:3], AARE/ASDCAS/ASADS/ASRE, AAOE/ASDRAS/ASOE, and
AAWE/ASDWE/ASWE, ASDCKE, ASOE3, and APDT.
For EMIFB, EMIF Bus consists of: BCE[3:0], BBE[1:0], BED[15:0], BEA[20:1], BARE/BSDCAS/BSADS/BSRE, BAOE/BSDRAS/BSOE, and
BAWE/BSDWE/BSWE, BSOE3, and BPDT.
‡ The EKxHZ bits in the EMIF Global Control register (GBLCTL) determine the state of the ECLKOUTx signals during HOLDA. If EKxHZ = 0,
ECLKOUTx continues clocking during Hold mode. If EKxHZ = 1, ECLKOUTx goes to high impedance during Hold mode, as shown in Figure 35.
Figure 35. HOLD/HOLDA Timing for EMIFA and EMIFB

BUSREQ TIMING
switching characteristics over recommended operating conditions for the BUSREQ cycles
for EMIFA and EMIFB modules (see Figure 36)
−600
−720
−1G
MIN MAX
1 td(AEKO1H-ABUSRV) Delay time, AECLKOUTx high to ABUSREQ valid 1 5.5 ns
2 td(BEKO1H-BBUSRV) Delay time, BECLKOUTx high to BBUSREQ valid 0.9 5.5 ns
ECLKOUTx
1 1
ABUSREQ
2 2
BBUSREQ
Figure 36. BUSREQ Timing for EMIFA and EMIFB

RESET TIMING
timing requirements for reset† (see Figure 37)
−600, −720,
NO. −850, −1G UNIT
MIN MAX
Width of the RESET pulse (PLL stable)‡ 250 µs
1 tw(RST)
Width of the RESET pulse (PLL needs to sync up)§ 250 µs
16 tsu(boot) Setup time, boot configuration bits valid before RESET high¶ 4E or 4C# ns
17 th(boot) Hold time, boot configuration bits valid after RESET high¶ 4P ns
18 tsu(PCLK-RSTH) Setup time, PCLK active before RESET high|| 32N ns
‡ This parameter applies to CLKMODE x1 when CLKIN is stable, and applies to CLKMODE x6, x12, x20 when CLKIN and PLL are stable.
§ This parameter applies to CLKMODE x6, x12, x20 only (it does not apply to CLKMODE x1). The RESET signal is not connected internally to
the clock PLL circuit. The PLL, however, may need up to 250 µs to stabilize following device power up or after PLL configuration has been
changed. During that time, RESET must be asserted to ensure proper device operation. See the clock PLL section for PLL lock times.
¶ EMIFB address pins BEA[20:13, 11, 9:7] are the boot configuration pins during device reset.
# E = 1/AECLKIN clock frequency in ns. C = 1/CLKIN clock frequency in ns. Select whichever value is larger for the MIN parameter.
|| N = the PCI input clock (PCLK) period in ns. When PCI is enabled (PCI_EN = 1), this parameter must be met.
switching characteristics over recommended operating conditions during reset†kh (see Figure 37)
−600, −720,
MIN MAX
2 td(RSTL-ECKI) Delay time, RESET low to ECLKIN synchronized internally 2E 3P + 20E ns
3 td(RSTH-ECKI) Delay time, RESET high to ECLKIN synchronized internally 2E 16 070P ns
4 td(RSTL-ECKO1HZ) Delay time, RESET low to ECLKOUT1 high impedance 2E ns
5 td(RSTH-ECKO1V) Delay time, RESET high to ECLKOUT1 valid 16 070P ns
6 td(RSTL-EMIFZHZ) Delay time, RESET low to EMIF Z high impedance 2E 3P + 4E ns
7 td(RSTH-EMIFZV) Delay time, RESET high to EMIF Z valid 16E 16 070P ns
8 td(RSTL-EMIFHIV) Delay time, RESET low to EMIF high group invalid 2E ns
9 td(RSTH-EMIFHV) Delay time, RESET high to EMIF high group valid 16 070P ns
10 td(RSTL-EMIFLIV) Delay time, RESET low to EMIF low group invalid 2E ns
11 td(RSTH-EMIFLV) Delay time, RESET high to EMIF low group valid 16 070P ns
12 td(RSTL-LOWIV) Delay time, RESET low to low group invalid 0 ns
13 td(RSTH-LOWV) Delay time, RESET high to low group valid 16 070P ns
14 td(RSTL-ZHZ) Delay time, RESET low to Z group high impedance 0 ns
15 td(RSTH-ZV) Delay time, RESET high to Z group valid 2P 16 070P ns
E = the EMIF input clock (ECLKIN, CPU/4 clock, or CPU/6 clock) period in ns for EMIFA or EMIFB.
EMIF Z group consists of: AEA[22:3], BEA[20:1], AED[63:0], BED[15:0], CE[3:0], ABE[7:0], BBE[1:0], ARE/SDCAS/SADS/SRE,
AWE/SDWE/SWE, and AOE/SDRAS/SOE, SOE3, ASDCKE, and PDT.
EMIF high group consists of: AHOLDA and BHOLDA (when the corresponding HOLD input is high)
EMIF low group consists of: ABUSREQ and BBUSREQ; AHOLDA and BHOLDA (when the corresponding HOLD input is low)
Low group consists of: XSP_CS, CLKX2/XSP_CLK, and DX2/XSP_DO; all of which apply only when PCI EEPROM (BEA13)
is enabled (with PCI_EN = 1 and MCBSP2_EN = 0). Otherwise, the CLKX2/XSP_CLK and DX2/XSP_DO
pins are in the Z group. For more details on the PCI configuration pins, see the Device Configurations section
of this data sheet.
Z group consists of: HD[31:0]/AD[31:0], CLKX0, CLKX1/URADDR4, CLKX2/XSP_CLK, FSX0, FSX1/UXADDR3, FSX2, DX0,
DX1/UXADDR4, DX2/XSP_DO, CLKR0, CLKR1/URADDR2, CLKR2, FSR0, FSR1/UXADDR2, FSR2,
TOUT0, TOUT1, TOUT2, GP[8:0], GP10/PCBE3, HR/W/PCBE2, HDS2/PCBE1, PCBE0, GP13/PINTA,
GP11/PREQ, HDS1/PSERR, HCS/PPERR, HCNTL1/PDEVSEL, HAS/PPAR, HCNTL0/PSTOP,
HHWIL/PTRDY (16-bit HPI mode only), HRDY/PIRDY, HINT/PFRAME, UXDATA[7:0], UXSOC, UXCLAV,
and URCLAV.

RESET TIMING (CONTINUED)

CLKOUT4
CLKOUT6
1
RESET
18
PCLK
2 3
ECLKIN
4 5
ECLKOUT1
ECLKOUT2
6 7
EMIF Z Group‡§
8 9
EMIF High Group‡
10 11
EMIF Low Group‡
12 13
Low Group‡
14 15
Z Group‡§
Boot and Device 16
17
Configuration Inputs§¶
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., ECLKIN, ECLKOUT1,
and ECLKOUT2].
‡ EMIF Z group consists of: AEA[22:3], BEA[20:1], AED[63:0], BED[15:0], CE[3:0], ABE[7:0], BBE[1:0], ARE/SDCAS/SADS/SRE,
AWE/SDWE/SWE, and AOE/SDRAS/SOE, SOE3, ASDCKE, and PDT.
EMIF high group consists of: AHOLDA and BHOLDA (when the corresponding HOLD input is high)
EMIF low group consists of: ABUSREQ and BBUSREQ; AHOLDA and BHOLDA (when the corresponding HOLD input is low)
Low group consists of: XSP_CS, CLKX2/XSP_CLK, and DX2/XSP_DO; all of which apply only when PCI EEPROM (BEA13)
is enabled (with PCI_EN = 1 and MCBSP2_EN = 0). Otherwise, the CLKX2/XSP_CLK and DX2/XSP_DO
pins are in the Z group. For more details on the PCI configuration pins, see the Device Configurations section
of this data sheet.
Z group consists of: HD[31:0]/AD[31:0], CLKX0, CLKX1/URADDR4, CLKX2/XSP_CLK, FSX0, FSX1/UXADDR3, FSX2, DX0,
DX1/UXADDR4, DX2/XSP_DO, CLKR0, CLKR1/URADDR2, CLKR2, FSR0, FSR1/UXADDR2, FSR2,
TOUT0, TOUT1, TOUT2, GP[8:0], GP10/PCBE3, HR/W/PCBE2, HDS2/PCBE1, PCBE0, GP13/PINTA,
GP11/PREQ, HDS1/PSERR, HCS/PPERR, HCNTL1/PDEVSEL, HAS/PPAR, HCNTL0/PSTOP,
HHWIL/PTRDY (16-bit HPI mode only), HRDY/PIRDY, HINT/PFRAME, UXDATA[7:0], UXSOC, UXCLAV,
and URCLAV.
§ If BEA[20:13, 11, 7] and HD5/AD5 pins are actively driven, care must be taken to ensure no timing contention between parameters 6, 7, 14, 15,
16, and 17.
¶ Boot and Device Configurations Inputs (during reset) include: EMIFB address pins BEA[20:13, 11, 9:7] and HD5/AD5.
The PCI_EN pin must be driven valid at all times and the user must not switch values throughout device operation.
The MCBSP2_EN pin must be driven valid at all times and the user can switch values throughout device operation.
Figure 37. Reset Timing†

EXTERNAL INTERRUPT TIMING
timing requirements for external interrupts† (see Figure 38)

−600
−720
NO. −850 UNIT
−1G
MIN MAX
Width of the NMI interrupt pulse low 4P ns
1 tw(ILOW)
Width of the EXT_INT interrupt pulse low 8P ns
Width of the NMI interrupt pulse high 4P ns
2 tw(IHIGH)
Width of the EXT_INT interrupt pulse high 8P ns
2
1
EXT_INTx, NMI
Figure 38. External/NMI Interrupt Timing

HOST-PORT INTERFACE (HPI) TIMING

timing requirements for host-port interface cycles†‡ (see Figure 39 through Figure 46)
−600
−850
NO. −720 UNIT
−1G
MIN MAX
1 tsu(SELV-HSTBL) Setup time, select signals§ valid before HSTROBE low 5 ns
2 th(HSTBL-SELV) Hold time, select signals§ valid after HSTROBE low 2.4 ns
3 tw(HSTBL) Pulse duration, HSTROBE low 4P¶ ns
4 tw(HSTBH) Pulse duration, HSTROBE high between consecutive accesses 4P ns
10 tsu(SELV-HASL) Setup time, select signals§ valid before HAS low 5 ns
11 th(HASL-SELV) Hold time, select signals§ valid after HAS low 2 ns
12 tsu(HDV-HSTBH) Setup time, host data valid before HSTROBE high 5 ns
13 th(HSTBH-HDV) Hold time, host data valid after HSTROBE high 2.8 ns
Hold time, HSTROBE low after HRDY low. HSTROBE should not be
14 th(HRDYL-HSTBL) inactivated until HRDY is active (low); otherwise, HPI writes will not complete 2 ns
properly.
18 tsu(HASL-HSTBL) Setup time, HAS low before HSTROBE low 2 ns
19 th(HSTBL-HASL) Hold time, HAS low after HSTROBE low 2.1 ns
† HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
‡ P = 1/CPU clock frequency in ns. For example, when running parts at 720 MHz, use P = 1.39 ns.
§ Select signals include: HCNTL[1:0] and HR/W. For HPI16 mode only, select signals also include HHWIL.
¶ Select the parameter value of 4P or 12.5 ns, whichever is greater.
switching characteristics over recommended operating conditions during host-port interface

cycles†‡ (see Figure 39 through Figure 46)
−600
−850
−1G
MIN MAX
6 td(HSTBL-HRDYH) Delay time, HSTROBE low to HRDY high# 1.3 4P + 8 ns
7 td(HSTBL-HDLZ) Delay time, HSTROBE low to HD low impedance for an HPI read 2 ns
8 td(HDV-HRDYL) Delay time, HD valid to HRDY low −3 ns
9 toh(HSTBH-HDV) Output hold time, HD valid after HSTROBE high 1.5 ns
15 td(HSTBH-HDHZ) Delay time, HSTROBE high to HD high impedance 12 ns
16 td(HSTBL-HDV) Delay time, HSTROBE low to HD valid (HPI16 mode, 2nd half-word only) 4P + 8 ns
# This parameter is used during HPID reads and writes. For reads, at the beginning of a word transfer (HPI32) or the first half-word transfer (HPI16)
on the falling edge of HSTROBE, the HPI sends the request to the EDMA internal address generation hardware, and HRDY remains high until
the EDMA internal address generation hardware loads the requested data into HPID. For writes, HRDY goes high if the internal write buffer is
full.

HOST-PORT INTERFACE (HPI) TIMING (CONTINUED)
HAS
1 1
2 2
HCNTL[1:0]
1 1
2 2
HR/W
1 1
2 2
HHWIL
4
3 3
HSTROBE†
HCS
15 15
7 9 16 9
HD[15:0] (output)
1st half-word 2nd half-word
6 8
HRDY
Figure 39. HPI16 Read Timing (HAS Not Used, Tied High)
HAS†
19 19
10 11
11 10
HCNTL[1:0]
11 11
10 10
HR/W
11 11
10 10
HHWIL
4
3
HSTROBE‡
18 18
HCS
15 15
7 9 16 9
HD[15:0] (output)
6 8
HRDY
† For correct operation, strobe the HAS signal only once per HSTROBE active cycle.
‡ HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 40. HPI16 Read Timing (HAS Used)

HAS
1 1
2 2
HCNTL[1:0]
1 1
2 2
HR/W
1 1
2 2
HHWIL
3 3
4
HSTROBE†
HCS
12 12
13 13
HD[15:0] (input)
6 14
HRDY
Figure 41. HPI16 Write Timing (HAS Not Used, Tied High)
19 19
HAS†
11 11
10 10
HCNTL[1:0]
11 11
10 10
HR/W
11 11
10 10
HHWIL
3
4
HSTROBE‡
18 18
HCS
12 12
13 13
HD[15:0] (input)
6 14
HRDY
Figure 42. HPI16 Write Timing (HAS Used)


HAS
1 2
HCNTL[1:0]
1 2
HR/W
3
HSTROBE†
HCS
7 9
15
HD[31:0] (output)
6 8
HRDY
Figure 43. HPI32 Read Timing (HAS Not Used, Tied High)
19
HAS†
11
10
HCNTL[1:0]
11
10
HR/W
18
3
HSTROBE‡
HCS
7 9
15
HD[31:0] (output)
6 8
HRDY
Figure 44. HPI32 Read Timing (HAS Used)

HAS
1 2
HCNTL[1:0]
1 2
HR/W
HSTROBE†
HCS
12 13
HD[31:0] (input)
6 14
HRDY
Figure 45. HPI32 Write Timing (HAS Not Used, Tied High)
19
HAS†
11
10
HCNTL[1:0]
11
10
HR/W
3
18
HSTROBE‡
HCS
12 13
HD[31:0] (input)
6 14
HRDY
Figure 46. HPI32 Write Timing (HAS Used)

PERIPHERAL COMPONENT INTERCONNECT (PCI) TIMING [C6415T AND C6416T ONLY]
timing requirements for PCLK†‡ (see Figure 47)

−600
−720
NO. −850 UNIT
−1G
MIN MAX
1 tc(PCLK) Cycle time, PCLK 30 (or 8P§) ns
2 tw(PCLKH) Pulse duration, PCLK high 11 ns
3 tw(PCLKL) Pulse duration, PCLK low 11 ns
4 tsr(PCLK) ∆v/∆t slew rate, PCLK 1 4 V/ns
† For 3.3-V operation, the reference points for the rise and fall transitions are measured at VILP MAX and VIHP MIN.
§ Select the parameter value of 30 ns or 8P, whichever is greater.
0.4 DVDD V MIN

1 Peak to Peak for
4 3.3V signaling
2
PCLK
3
4
Figure 47. PCLK Timing
timing requirements for PCI reset (see Figure 48)

−600
−720
NO. −850 UNIT
−1G
MIN MAX
1 tw(PRST) Pulse duration, PRST 1 ms
2 tsu(PCLKA-PRSTH) Setup time, PCLK active before PRST high 100 µs
PCLK
PRST
Figure 48. PCI Reset (PRST) Timing


(CONTINUED)
timing requirements for PCI inputs (see Figure 49)

−600
−720
NO. −850 UNIT
−1G
MIN MAX
5 tsu(IV-PCLKH) Setup time, input valid before PCLK high 7 ns
6 th(IV-PCLKH) Hold time, input valid after PCLK high 0 ns
switching characteristics over recommended operating conditions for PCI outputs (see Figure 49)
−600
−720
−1G
MIN MAX
1 td(PCLKH-OV) Delay time, PCLK high to output valid 11 ns
2 td(PCLKH-OIV) Delay time, PCLK high to output invalid 2 ns
3 td(PCLKH-OLZ) Delay time, PCLK high to output low impedance 2 ns
4 td(PCLKH-OHZ) Delay time, PCLK high to output high impedance 28 ns
PCLK
1
2
PCI Output Valid

3
4
PCI Input Valid
5
6
Figure 49. PCI Input/Output Timing


(CONTINUED)
timing requirements for serial EEPROM interface (see Figure 50)

−600
−720
NO. −850 UNIT
−1G
MIN MAX
8 tsu(DIV-CLKH) Setup time, XSP_DI valid before XSP_CLK high 50 ns
9 th(CLKH-DIV) Hold time, XSP_DI valid after XSP_CLK high 0 ns
switching characteristics over recommended operating conditions for serial EEPROM interface†
(see Figure 50)
−600
−720
−1G
MIN TYP MAX
1 tw(CSL) Pulse duration, XSP_CS low 4092P ns
2 td(CLKL-CSL) Delay time, XSP_CLK low to XSP_CS low 0 ns
3 td(CSH-CLKH) Delay time, XSP_CS high to XSP_CLK high 2046P ns
4 tw(CLKH) Pulse duration, XSP_CLK high 2046P ns
5 tw(CLKL) Pulse duration, XSP_CLK low 2046P ns
6 tosu(DOV-CLKH) Output setup time, XSP_DO valid before XSP_CLK high 2046P ns
7 toh(CLKH-DOV) Output hold time, XSP_DO valid after XSP_CLK high 2046P ns
2
1
XSP_CS
3 4
5
XSP_CLK
6 7
XSP_DO
9
8
XSP_DI
Figure 50. PCI Serial EEPROM Interface Timing

MULTICHANNEL BUFFERED SERIAL PORT (McBSP) TIMING
timing requirements for McBSP† (see Figure 51)

−600
−720
NO. −850 UNIT
−1G
MIN MAX
2 tc(CKRX) Cycle time, CLKR/X CLKR/X ext 4P or 6.67‡§¶ ns
3 tw(CKRX) Pulse duration, CLKR/X high or CLKR/X low CLKR/X ext 0.5tc(CKRX) − 1# ns
CLKR int 9
5 tsu(FRH-CKRL) Setup time, external FSR high before CLKR low ns
CLKR ext 1.3
CLKR int 6
6 th(CKRL-FRH) Hold time, external FSR high after CLKR low ns
CLKR ext 3
CLKR int 8
7 tsu(DRV-CKRL) Setup time, DR valid before CLKR low ns
CLKR ext 0.9
CLKR int 3
8 th(CKRL-DRV) Hold time, DR valid after CLKR low ns
CLKR ext 3.1
CLKX int 9
10 tsu(FXH-CKXL) Setup time, external FSX high before CLKX low ns
CLKX ext 1.3
CLKX int 6
11 th(CKXL-FXH) Hold time, external FSX high after CLKX low ns
CLKX ext 3
† CLKRP = CLKXP = FSRP = FSXP = 0. If polarity of any of the signals is inverted, then the timing references of that signal are also inverted.
‡ Minimum CLKR/X cycle times must be met, even when CLKR/X is generated by an internal clock source. Minimum CLKR/X cycle times are based
on internal logic speed; the maximum usable speed may be lower due to EDMA limitations and AC timing requirements.
§ P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
¶ Use whichever value is greater.
# This parameter applies to the maximum McBSP frequency. Operate serial clocks (CLKR/X) in the reasonable range of 40/60 duty cycle.

MULTICHANNEL BUFFERED SERIAL PORT (McBSP) TIMING (CONTINUED)
switching characteristics over recommended operating conditions for McBSP†‡ (see Figure 51)
−600
−720
−1G
MIN MAX
Delay time, CLKS high to CLKR/X high for internal CLKR/X generated
1 td(CKSH-CKRXH) 1.4 10 ns
from CLKS input
2 tc(CKRX) Cycle time, CLKR/X CLKR/X int 4P or 6.67§¶# ns
3 tw(CKRX) Pulse duration, CLKR/X high or CLKR/X low CLKR/X int C − 1|| C + 1|| ns
4 td(CKRH-FRV) Delay time, CLKR high to internal FSR valid CLKR int −2.1 3 ns
CLKX int −1.7 3
9 td(CKXH-FXV) Delay time, CLKX high to internal FSX valid ns
CLKX ext 1.7 9
Disable time, DX high impedance following last data bit CLKX int −3.9 4
12 tdis(CKXH-DXHZ) ns
from CLKX high CLKX ext 2 9
CLKX int −3.9 + D1 4 + D2
13 td(CKXH-DXV) Delay time, CLKX high to DX valid ns
CLKX ext 2.0 + D1 9 + D2
Delay time, FSX high to DX valid FSX int −2.3 + D1 5.6 + D2
14 td(FXH-DXV) ns
ONLY applies when in data
FSX ext 1.9 + D1 9 + D2
delay 0 (XDATDLY = 00b) mode
† CLKRP = CLKXP = FSRP = FSXP = 0. If polarity of any of the signals is inverted, then the timing references of that signal are also inverted.
‡ Minimum delay times also represent minimum output hold times.
§ Minimum CLKR/X cycle times must be met, even when CLKR/X is generated by an internal clock source. Minimum CLKR/X cycle times are based
on internal logic speed; the maximum usable speed may be lower due to EDMA limitations and AC timing requirements.
¶ P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
# Use whichever value is greater.
|| C = H or L
S = sample rate generator input clock = 4P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
CLKGDV should be set appropriately to ensure the McBSP bit rate does not exceed the maximum limit (see ¶ footnote above).
Extra delay from CLKX high to DX valid applies only to the first data bit of a device, if and only if DXENA = 1 in SPCR.
if DXENA = 0, then D1 = D2 = 0
if DXENA = 1, then D1 = 4P, D2 = 8P
Extra delay from FSX high to DX valid applies only to the first data bit of a device, if and only if DXENA = 1 in SPCR.
if DXENA = 0, then D1 = D2 = 0
if DXENA = 1, then D1 = 4P, D2 = 8P

CLKS
1
2
3
3
CLKR
4
4
FSR (int)
5
6
FSR (ext)
7
8
DR Bit(n-1) (n-2) (n-3)
2
3
3
CLKX
9
FSX (int)
11
10
FSX (ext)
FSX (XDATDLY=00b)
14 13†
12 13†
DX Bit 0 Bit(n-1) (n-2) (n-3)
† Parameter No. 13 applies to the first data bit only when XDATDLY ≠ 0
Figure 51. McBSP Timing

timing requirements for FSR when GSYNC = 1 (see Figure 52)

−600
−720
NO. −850 UNIT
−1G
MIN MAX
1 tsu(FRH-CKSH) Setup time, FSR high before CLKS high 4 ns
2 th(CKSH-FRH) Hold time, FSR high after CLKS high 4 ns
CLKS
1
2
FSR external
CLKR/X (no need to resync)
CLKR/X (needs resync)
Figure 52. FSR Timing When GSYNC = 1

timing requirements for McBSP as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0†‡ (see Figure 53)
−600
−720
−850
NO. −1G UNIT
MASTER SLAVE
MIN MAX MIN MAX
4 tsu(DRV-CKXL) Setup time, DR valid before CLKX low 12 2 − 12P ns
5 th(CKXL-DRV) Hold time, DR valid after CLKX low 4 5 + 24P ns
‡ For all SPI Slave modes, CLKG is programmed as 1/4 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics over recommended operating conditions for McBSP as SPI Master or
Slave: CLKSTP = 10b, CLKXP = 0†‡ (see Figure 53)
−600
−720
−850
NO. PARAMETER −1G UNIT
MASTER§ SLAVE
MIN MAX MIN MAX
1 th(CKXL-FXL) Hold time, FSX low after CLKX low¶ T−2 T+3 ns
2 td(FXL-CKXH) Delay time, FSX low to CLKX high# L−2 L+3 ns
3 td(CKXH-DXV) Delay time, CLKX high to DX valid −2 4 12P + 2.8 20P + 17 ns
Disable time, DX high impedance following last data bit from
6 tdis(CKXL-DXHZ) L−2 L+3 ns
CLKX low
7 tdis(FXH-DXHZ) 4P + 3 12P + 17 ns
FSX high
8 td(FXL-DXV) Delay time, FSX low to DX valid 8P + 1.8 16P + 17 ns
§ S = Sample rate generator input clock = 4P if CLKSM = 1 (P = 1/CPU clock frequency)
= Sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
¶ FSRP = FSXP = 1. As a SPI Master, FSX is inverted to provide active-low slave-enable output. As a Slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for Master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for Slave McBSP
# FSX should be low before the rising edge of clock to enable Slave devices and then begin a SPI transfer at the rising edge of the Master clock
(CLKX).

CLKX
1 2
FSX
7 8
6 3
DX Bit 0 Bit(n-1) (n-2) (n-3) (n-4)
4
5
DR Bit 0 Bit(n-1) (n-2) (n-3) (n-4)
Figure 53. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0

−600, −720
−850, −1G
NO. UNIT
MASTER SLAVE
MIN MAX MIN MAX
4 tsu(DRV-CKXH) Setup time, DR valid before CLKX high 12 2 − 12P ns
5 th(CKXH-DRV) Hold time, DR valid after CLKX high 4 5 + 24P ns
−600, −720
−850, −1G
NO. PARAMETER UNIT
MASTER§ SLAVE
MIN MAX MIN MAX
1 th(CKXL-FXL) Hold time, FSX low after CLKX low¶ L−2 L+3 ns
2 td(FXL-CKXH) Delay time, FSX low to CLKX high# T−2 T+3 ns
3 td(CKXL-DXV) Delay time, CLKX low to DX valid −2 4 12P + 2.8 20P + 17 ns
6 tdis(CKXL-DXHZ) −2 4 12P + 3 20P + 17 ns
CLKX low
7 td(FXL-DXV) Delay time, FSX low to DX valid H−2 H+4 8P + 2 16P + 17 ns
(CLKX).
CLKX
1 2
FSX
6 7 3
DX Bit 0 Bit(n-1) (n-2) (n-3) (n-4)
4 5
DR Bit 0 Bit(n-1) (n-2) (n-3) (n-4)

−600
−720
−850
NO. −1G UNIT
MASTER SLAVE
MIN MAX MIN MAX
−600
−720
−850
MASTER§ SLAVE
MIN MAX MIN MAX
1 th(CKXH-FXL) Hold time, FSX low after CLKX high¶ T−2 T+3 ns
2 td(FXL-CKXL) Delay time, FSX low to CLKX low# H−2 H+3 ns
3 td(CKXL-DXV) Delay time, CLKX low to DX valid −2 4 12P + 2.8 20P + 17 ns
Disable time, DX high impedance following last data bit
6 tdis(CKXH-DXHZ) H−2 H+3 ns
from CLKX high
7 tdis(FXH-DXHZ) 4P + 3 12P + 17 ns
from FSX high
8 td(FXL-DXV) Delay time, FSX low to DX valid 8P + 2 16P + 17 ns
(CLKX).

CLKX
1 2
FSX
7
6 8 3
DX Bit 0 Bit(n-1) (n-2) (n-3) (n-4)
4 5
DR Bit 0 Bit(n-1) (n-2) (n-3) (n-4)

−600
−720
−850
NO. −1G UNIT
MASTER SLAVE
MIN MAX MIN MAX
−600
−720
−850
MASTER§ SLAVE
MIN MAX MIN MAX
1 th(CKXH-FXL) Hold time, FSX low after CLKX high¶ H−2 H+3 ns
2 td(FXL-CKXL) Delay time, FSX low to CLKX low# T−2 T+1 ns
3 td(CKXH-DXV) Delay time, CLKX high to DX valid −2 4 12P + 2.8 20P + 17 ns
6 tdis(CKXH-DXHZ) −2 4 12P + 3 20P + 17 ns
from CLKX high
7 td(FXL-DXV) Delay time, FSX low to DX valid L−2 L+4 8P + 2 16P + 17 ns
(CLKX).

CLKX
1 2
FSX
6 7 3
DX Bit 0 Bit(n-1) (n-2) (n-3) (n-4)
4
5
DR Bit 0 Bit(n-1) (n-2) (n-3) (n-4)

UTOPIA SLAVE TIMING [C6415T AND C6416T ONLY]
timing requirements for UXCLK† (see Figure 57)

−600
−720
NO. −850 UNIT
−1G
MIN MAX
1 tc(UXCK) Cycle time, UXCLK 20 ns
2 tw(UXCKH) Pulse duration, UXCLK high 0.4tc(UXCK) 0.6tc(UXCK) ns
3 tw(UXCKL) Pulse duration, UXCLK low 0.4tc(UXCK) 0.6tc(UXCK) ns
4 tt(UXCK) Transition time, UXCLK 2 ns
1
4
2
UXCLK
3
4
Figure 57. UXCLK Timing
timing requirements for URCLK† (see Figure 58)

−600
−720
NO. −850 UNIT
−1G
MIN MAX
1 tc(URCK) Cycle time, URCLK 20 ns
2 tw(URCKH) Pulse duration, URCLK high 0.4tc(URCK) 0.6tc(URCK) ns
3 tw(URCKL) Pulse duration, URCLK low 0.4tc(URCK) 0.6tc(URCK) ns
4 tt(URCK) Transition time, URCLK 2 ns
1
4
2
URCLK
3
4
Figure 58. URCLK Timing

UTOPIA SLAVE TIMING [C6415T AND C6416T ONLY] (CONTINUED)
timing requirements for UTOPIA Slave transmit (see Figure 59)

−600, −720
NO. −850, −1G UNIT
MIN MAX
2 tsu(UXAV-UXCH) Setup time, UXADDR valid before UXCLK high 4 ns
3 th(UXCH-UXAV) Hold time, UXADDR valid after UXCLK high 1 ns
8 tsu(UXENBL-UXCH) Setup time, UXENB low before UXCLK high 4 ns
9 th(UXCH-UXENBL) Hold time, UXENB low after UXCLK high 1 ns
switching characteristics over recommended operating conditions for UTOPIA Slave transmit
(see Figure 59)
−600, −720
MIN MAX
1 td(UXCH-UXDV) Delay time, UXCLK high to UXDATA valid 3 12 ns
4 td(UXCH-UXCLAV) Delay time, UXCLK high to UXCLAV driven active value 3 12 ns
5 td(UXCH-UXCLAVL) Delay time, UXCLK high to UXCLAV driven inactive low 3 12 ns
6 td(UXCH-UXCLAVHZ) Delay time, UXCLK high to UXCLAV going Hi-Z 9 18.5 ns
7 tw(UXCLAVL-UXCLAVHZ) Pulse duration (low), UXCLAV low to UXCLAV Hi-Z 3 ns
10 td(UXCH-UXSV) Delay time, UXCLK high to UXSOC valid 3 12 ns
UXCLK
1
UXDATA[7:0] P45 P46 P47 P48 H1
3
2
UXADDR[4:0] 0 x1F N 0x1F N 0x1F N+1 0x1F
6
7
4 5
UXCLAV N N
9 8
UXENB
10
UXSOC
† The UTOPIA Slave module has signals that are middle-level signals indicating a high-impedance state (i.e., the UXCLAV and
UXSOC signals).
Figure 59. UTOPIA Slave Transmit Timing†

UTOPIA SLAVE TIMING [C6415T AND C6416T ONLY] (CONTINUED)

timing requirements for UTOPIA Slave receive (see Figure 60)
−600, −720
NO. −850, −1G UNIT
MIN MAX
1 tsu(URDV-URCH) Setup time, URDATA valid before URCLK high 4 ns
2 th(URCH-URDV) Hold time, URDATA valid after URCLK high 1 ns
3 tsu(URAV-URCH) Setup time, URADDR valid before URCLK high 4 ns
4 th(URCH-URAV) Hold time, URADDR valid after URCLK high 1 ns
9 tsu(URENBL-URCH) Setup time, URENB low before URCLK high 4 ns
10 th(URCH-URENBL) Hold time, URENB low after URCLK high 1 ns
11 tsu(URSH-URCH) Setup time, URSOC high before URCLK high 4 ns
12 th(URCH-URSH) Hold time, URSOC high after URCLK high 1 ns
switching characteristics over recommended operating conditions for UTOPIA Slave receive
(see Figure 60)
−600, −720
MIN MAX
5 td(URCH-URCLAV) Delay time, URCLK high to URCLAV driven active value 3 12 ns
6 td(URCH-URCLAVL) Delay time, URCLK high to URCLAV driven inactive low 3 12 ns
7 td(URCH-URCLAVHZ) Delay time, URCLK high to URCLAV going Hi-Z 9 18.5 ns
8 tw(URCLAVL-URCLAVHZ) Pulse duration (low), URCLAV low to URCLAV Hi-Z 3 ns
URCLK
2
1
URDATA[7:0] P48 H1 H2 H3
4
3
URADDR[4:0] N 0x1F N+1 0x1F N+2 0x1F
7
8
5 6
URCLAV N N+1 N+2
10 9
URENB
11 12
URSOC
† The UTOPIA Slave module has signals that are middle-level signals indicating a high-impedance state (i.e., the URCLAV and
URSOC signals).
Figure 60. UTOPIA Slave Receive Timing†

TIMER TIMING
timing requirements for timer inputs† (see Figure 61)

−600
−720
NO. −850 UNIT
−1G
MIN MAX
1 tw(TINPH) Pulse duration, TINP high 8P ns
2 tw(TINPL) Pulse duration, TINP low 8P ns
switching characteristics over recommended operating conditions for timer outputs†

(see Figure 61)
−600
−720
−1G
MIN MAX
3 tw(TOUTH) Pulse duration, TOUT high 8P −3 ns
4 tw(TOUTL) Pulse duration, TOUT low 8P −3 ns
2
1
TINPx 4
3
TOUTx
Figure 61. Timer Timing

GENERAL-PURPOSE INPUT/OUTPUT (GPIO) PORT TIMING
timing requirements for GPIO inputs†‡ (see Figure 62)

−600
−720
NO. −850 UNIT
−1G
MIN MAX
1 tw(GPIH) Pulse duration, GPIx high 8P ns
2 tw(GPIL) Pulse duration, GPIx low 8P ns
‡ The pulse width given is sufficient to generate a CPU interrupt or an EDMA event. However, if a user wants to have the DSP recognize the GPIx
changes through software polling of the GPIO register, the GPIx duration must be extended to at least 12P to allow the DSP enough time to access
the GPIO register through the CFGBUS.
switching characteristics over recommended operating conditions for GPIO outputs†

(see Figure 62)
−600
−720
−1G
MIN MAX
3 tw(GPOH) Pulse duration, GPOx high 24P − 8§ ns
4 tw(GPOL) Pulse duration, GPOx low 24P − 8§ ns
§ This parameter value should not be used as a maximum performance specification. Actual performance of back-to-back accesses of the GPIO
is dependent upon internal bus activity.
2
1
GPIx 4
3
GPOx
Figure 62. GPIO Port Timing

JTAG TEST-PORT TIMING
timing requirements for JTAG test port (see Figure 63)

−600
−720
NO. −850 UNIT
−1G
MIN MAX
1 tc(TCK) Cycle time, TCK 35 ns
3 tsu(TDIV-TCKH) Setup time, TDI/TMS/TRST valid before TCK high 10 ns
4 th(TCKH-TDIV) Hold time, TDI/TMS/TRST valid after TCK high 9 ns
switching characteristics over recommended operating conditions for JTAG test port
(see Figure 63)
−600
−720
−1G
MIN MAX
2 td(TCKL-TDOV) Delay time, TCK low to TDO valid 0 18 ns
TCK
2 2
TDO
4
3
TDI/TMS/TRST
Figure 63. JTAG Test-Port Timing

MECHANICAL DATA FOR C6414T, C6415T, AND C6416T
The following table(s) show the thermal resistance characteristics for the PBGA — GLZ, ZLZ and CLZ
mechanical packages.
thermal resistance characteristics (S-PBGA package) [GLZ]

°C/W
NO. Air Flow (m/s†) °C/W‡
(with Heat Sink§)
1 RΘJC Junction-to-case N/A 3.11 3.11
2 RΘJB Junction-to-board N/A 9.95 9.95
3 RΘJA Junction-to-free air 0.00 19.6 14.4
7 PsiJT Junction-to-package top N/A 0.83 0.83
8 PsiJB Junction-to-board N/A 7.88 7.88
† m/s = meters per second
‡ Numbers are based on simulations.
§ These thermal resistance numbers were modeled using a heat sink, part number 374024B00035, manufactured by AAVID Thermalloy. AAVID
Thermalloy also manufactures a similar epoxy-mounted heat sink, part number 374024B00000. When operating at 1 GHz, a heat sink is
required to reduce the thermal resistance characteristics of the package. TI recommends a passive, laminar heat sink, similar to the part
numbers mentioned above.
thermal resistance characteristics (S-PBGA package) [ZLZ]

°C/W
(with Heat Sink§)

thermal resistance characteristics (S-PBGA package) [CLZ]

°C/W
(with Heat Sink§)
packaging information
The following addendum table (device orderables) and packaging information reflect the most current released
data available for the TMS320C6414/TMS320C6415T/TMS320C6416T device(s) — GLZ, ZLZ and CLZ. This
data is subject to change without notice and without revision of this document.

PACKAGE OPTION ADDENDUM
www.ti.com 15-May-2008
PACKAGING INFORMATION
Orderable Device Status (1) Package Package Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Type Drawing Qty
TMS320C6414TBCLZ6 ACTIVE FC/CSP CLZ 532 TBD Call TI Call TI
TMS320C6414TBGLZ1 ACTIVE FCBGA GLZ 532 60 TBD SNPB Level-4-220C-72 HR
TMS320C6414TBGLZA6 ACTIVE FCBGA GLZ 532 60 TBD SNPB Level-4-220C-72 HR
TMS320C6414TBZLZ1 ACTIVE FCBGA ZLZ 532 60 Pb-Free (RoHS SNAGCU Level-4-260C-72HR
Exempt)
Exempt)
Exempt)
Exempt)
TMS320C6414TBZLZA6 ACTIVE FCBGA ZLZ 532 60 Pb-Free (RoHS SNAGCU Level-4-260C-72HR
Exempt)
Exempt)
Exempt)
TMS320C6414TGLZ1 OBSOLETE FCBGA GLZ 532 TBD Call TI Call TI
TMS320C6414TGLZA6 OBSOLETE FCBGA GLZ 532 TBD Call TI Call TI
TMS320C6414TZLZ1 OBSOLETE FCBGA ZLZ 532 TBD Call TI Call TI
TMS320C6414TZLZA6 OBSOLETE FCBGA ZLZ 532 TBD Call TI Call TI
TMS320C6415TBGLZ8 ACTIVE FCBGA GLZ 532 TBD Call TI Call TI
TMS320C6415TBGLZA6 ACTIVE FCBGA GLZ 532 TBD Call TI Call TI
Addendum-Page 1
Type Drawing Qty
Exempt)
Exempt)
Exempt)
TMS320C6415TBZLZ8 ACTIVE FCBGA ZLZ 532 TBD Call TI Call TI
Exempt)
TMS320C6415TBZLZA7 ACTIVE FCBGA ZLZ 532 TBD Call TI Call TI
Exempt)
TMS320C6416TBGLZA6 ACTIVE FCBGA GLZ 532 60 Pb-Free (RoHS SNPB Level-4-260C-72HR
Exempt)
Exempt)
Exempt)
TMS320C6416TBZLZA6 ACTIVE FCBGA ZLZ 532 TBD Call TI Call TI
Exempt)
TMS320C6416TBZLZD1 ACTIVE FCBGA ZLZ 532 60 Pb-Free (RoHS SNAGCU Level-4-260C-72HR
Exempt)
Addendum-Page 2
Type Drawing Qty
TMX320C6414TGLZ ACTIVE FCBGA GLZ 532 TBD Call TI Call TI
TMX320C6414TGLZ1 ACTIVE FCBGA GLZ 532 TBD Call TI Call TI
TMX320C6416TGLZ ACTIVE FCBGA GLZ 532 TBD Call TI Call TI
TMX320C6416TGLZ1 ACTIVE FCBGA GLZ 532 TBD Call TI Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 3

MPBG175B − OCTOBER 2000 − REVISED FEBRUARY 2002
GLZ (S-PBGA-N532) PLASTIC BALL GRID ARRAY
23,10
SQ 20,00 TYP
22,90
0,80
0,40
AF
AE
AD
AC
AB
AA
Y
W
0,80
V
U
T
R
P
A1 Corner N
M
L
0,40
K
J
H
G
F
E
D
C
B
A
1 3 5 7 9 11 13 15 17 19 21 23 25
2 4 6 8 10 12 14 16 18 20 22 24 26
Heat Slug Bottom View
3,30 MAX
1,00 NOM
Seating Plane
0,55
0,10 M 0,45 0,12
0,45
0,35
4201884/C 11/01
NOTES: A. All linear dimensions are in millimeters.

B. This drawing is subject to change without notice.
C. Thermally enhanced plastic package with heat slug (HSL)
D. Flip chip application only
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1

IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Amplifiers amplifier.ti.com Audio www.ti.com/audio
Data Converters dataconverter.ti.com Automotive www.ti.com/automotive
DSP dsp.ti.com Broadband www.ti.com/broadband
Clocks and Timers www.ti.com/clocks Digital Control www.ti.com/digitalcontrol
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Military www.ti.com/military
Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork
Microcontrollers microcontroller.ti.com Security www.ti.com/security
RFID www.ti-rfid.com Telephony www.ti.com/telephony
RF/IF and ZigBee® Solutions www.ti.com/lprf Video & Imaging www.ti.com/video
Wireless www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated

Datasheet

Uploaded by

Copyright:

Available Formats

Datasheet

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Datasheet

Uploaded by

Copyright:

Available Formats



Highest-Performance Fixed-Point DSPs Two External Memory Interfaces (EMIFs)

C62x, VelociTI.2, VelociTI, and TMS320C64x are trademarks of Texas Instruments.

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443 1

2 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443

The TMS320C6414T/C6415T/C6416T devices at all speeds now support an “M version” commercial

Global − Added the M version, commercial temperature range of 0C to 90C.

absolute maximum ratings over operating case temperature range table,

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443 3

GLZ, ZLZ and CLZ BGA packages (bottom view)

4 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443

TMS320C6000, C64x, and C6000 are trademarks of Texas Instruments.

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443 5

On-Chip Memory 16K-Byte (16KB) L1 Program (L1P) Cache

6 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443 7

functional block and CPU (DSP core) diagram

C64x Digital Signal Processor

Timer 2 Instruction Fetch Control

.L1 .S1 .M1 .D1 .D2 .M2 .S2 .L2 Interrupt

8 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443

CPU (DSP core) description

TMS320C62x is a trademark of Texas Instruments.

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443 9

CPU (DSP core) description (continued)

TMS320C67x is a trademark of Texas Instruments.

10 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443

CPU (DSP core) description (continued)

long dst See Note A

Figure 1. TMS320C64x CPU (DSP Core) Data Paths

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443 11

memory map summary

12 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443

Table 3. TMS320C6414T, C6415T, C6416T Memory Map Summary

MEMORY BLOCK DESCRIPTION BLOCK SIZE (BYTES) HEX ADDRESS RANGE

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443 13

L2MODE L2 Memory Block Base Address

000 001 010 011 111

ÎÎÎÎÎÎÎÎÎÎ 0x000C 0000

Figure 2. TMS320C6414T/C6415T/C6416T L2 Architecture Memory Configuration

14 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443

peripheral register descriptions

Table 4. EMIFA Registers

HEX ADDRESS RANGE ACRONYM REGISTER NAME

Table 5. EMIFB Registers

HEX ADDRESS RANGE ACRONYM REGISTER NAME

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443 15

peripheral register descriptions (continued)

Table 6. L2 Cache Registers

16 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443

peripheral register descriptions (continued)

Table 6. L2 Cache Registers (Continued)

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443 17

peripheral register descriptions (continued)

Table 6. L2 Cache Registers (Continued)

18 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443

peripheral register descriptions (continued)

Table 7. EDMA Registers

HEX ADDRESS RANGE ACRONYM REGISTER NAME