EGT346

36.
036/1
EGT 346...348: Stem-type temperature sensor

How energy efficiency is improved
Accurate detection of duct temperature for energy-efficient control of HVAC systems and monitoring
energy consumption.
Areas of application
Temperature measurement of liquids and gases in ventilation systems, water networks and air ducting.
Properties
• Passive measured value acquisition
• Can be used in pipes and tanks with optional LW7 protective tubes (pockets)
• Cable entry with cord grip
Technical description
• Measurement is effected with a nickel thin-film sensor as per DIN 43760
• Housing made of yellow and black flame-retardant thermoplastic (RAL 9010)
• Cable clamping sleeve Pg 11
• Screw terminals for wires up to 1,5 mm²
• Immersion stem made of 6.5 mm ø copper (without protective tube) T
• Active length 15 mm
Type Stem Nominal value Measuring range Weight
mm at 0°C °C kg
Y01875
EGT 346 F021 120 200 Ω –30...130 0,07
EGT 346 F101 120 1000 Ω –30...130 0,07
EGT 347 F021 225 200 Ω –30...130 0,08
EGT 347 F101 225 1000 Ω –30...130 0,08
EGT 348 F021 450 200 Ω –30...130 0,10
EGT 348 F101 450 1000 Ω –30...130 0,10
Resistance values as per DIN 43760 Max. temp. at head 80 °C

Tolerance at 0 °C ± 0,4 K Degree of protection IP 42 (EN 60529)
Mean temp. coefficient 0,00618 K-1
Self-warming (in air) 0,25 K/mW Wiring diagram A01632
Time characteristic: Dimension drawing M08527
in air, without prot. Tube Dead time Time const. Fitting instructions MV 505497
still 18 s 330 s
moving (3 m/s) 9s 60 s
in water, with prot. tube 1) Dead time Time const.
still 7s 28 s
moving (0,4 m/s) 6s 27 s
Accessories
0364439 . . . Protective tube LW 7, brass; see chapter 39
0226811 . . . Protective tube LW 7, inox; see chapter 39
0368840 000* Holder for fitting stem on wall
0368839 000* Holder for fitting stem in air duct
0313220 001 Heat-conducting paste, in a tube of 20 g
0313282 001 Clamp D = 15 mm / 7 mm, for fitting sensor into protective tube; separate delivery
0313346 001* Module 0-10 V for Ni1000; 24 V~; MV 505513; A08091, IP 00 (IP 42 when fitted in
housing) 4 temp. ranges: –50...0 °C; –50...50 °C; 0...50 °C; 0...100 °C
*) Dimension drawing or wiring diagram are available under the same number
1) With heat-conducting paste
Operation
The resistance value of the Ni measuring resistor changes with respect to temperature. The tempera-
ture coefficient is always positive, i.e. the resistance value increases as the temperature rises. See
table of values (DIN 43760) and curve. The elements are exchangeable (within the limits of the pre-
scribed tolerances)
Sauter Components 7136036003 03

36.036/2 EGT 346...348
Further details on the accessories

The module evaluates the signal of an Ni1000 measuring resistor and converts it into an output signal of
0...10 V. The module is fitted in the sensor housing.
Input temperature sensor Ni1000 Output 0...10 V, load > 5 kΩ
Measuring range can be changed –50...0 °C Ambient temperature –30...80 °C
–50...50 °C Degree of protection IP 00 (IP 42
0...50 °C (factory setting) fitted in housing)
0...100 °C Auxiliary supply 24 V~ ± 20%
Error max. 1 °C zero-point error
max. 1 °C span error
Additional technical data

Complies with:-
EMC directive 2004/108/EC EN 61000-6-1/ EN 61000-6-2
EN 61000-6-3/ EN 61000-6-4
Engineering and fitting note

In water:
For use in pipes and containers, the detec-
tor must be fitted into a protective tube
(LW 7) using the holder. The detector can
be adjusted so as to account for different
thicknesses of pipe insulation. It should be
fitted against the direction of flow.
In air ducts:
The detector is fitted directly onto the insula-
tion or onto the wall of the air duct.
Using the stem holder (accessory
no. 0368839) and the clamping ring (acces-
sory no. 0313282) the insertion depth can
be adjusted.

EGT 346...348 36.036/3
Wiring diagram Dimension drawing

1 2
A01632
Accessories
0...10V 313346
24V~ xi EGT . . .
2 1 3
ON -50...0°C
-50..50°C
12
0...50°C
0...100°C
Ni1000
A08091a
368839
16
Ø55
38 M08527a
5,8
15,3
120° M00827a
368840
Ø 5,8
15,5
25,5
35
15,3
20
M00829a
Printed in Switzerland
Right of amendment reserved
N.B.: A comma between cardinal
numbers denotes a decimal point
© Fr. Sauter AG, CH-4016 Basle

EGT346

Uploaded by

Copyright:

Available Formats

EGT346

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

EGT346

Uploaded by

Copyright:

Available Formats

36.

EGT 346...348: Stem-type temperature sensor

Resistance values as per DIN 43760 Max. temp. at head 80 °C

1) With heat-conducting paste

Sauter Components 7136036003 03

Further details on the accessories

Additional technical data

Engineering and fitting note

Sauter Components 7136036003 03

Wiring diagram Dimension drawing

You might also like