Catb2001e C

Ceramic&Exsev bearing series Exsev bearings for use in
a vacuum environment
More and more bearings are being used in extreme special

environments, such as in a vacuum, or in a clean, corrosive, or
heated place. In some cases bearings are required to be insu- Bore diameter 4 – 40 mm
lated or antimagnetic.
Applications of bearings in such environments are increas- Exsev bearings for use in
ing in the field of state-of-the-art technology, e.g. vacuum a clean environment
equipment, aerospace equipment and semi-conductor produc-
tion facilities. Bearings made of conventional materials and
lubricants can hardly meet these new needs.
JTEKT has succeeded in developing a series of bearings
for use in extreme special environments, having started from Bore diameter 4 – 40 mm
the study of the very basics of materials and testing of their
performance under various severe conditions. Ceramic bearings
JTEKT has standardized the following bearings as the
"Koyo bearing series".
¡Exsev bearings for use in a clean environment

Designed for use in a vacuum. Bore diameter 4 – 120 mm
The friction surface of the bearing interior is coated with
solid lubricant (or soft metal). Bearings pre-lubricated with Linear ball bearings for
special grease are also available. vacuum
¡Exsev bearings for use in a vacuum environment

Produce insignificant contamination, provided with
rolling elements and a cage made of self-lubricating Ball complement
materials. Optimal for use in environments which need to bore diameter 3 – 40 mm
be clean.
¡Ceramic bearings
Ceramic rings and rolling elements (silicon nitride Si3N4)
ensure excellent performance in various extreme special
environments.
¡For details, refer to JTEKT separate catalog "Ceramic

bearings and bearings for extreme special
environments" (CAT. NO. B2004E).
C1 C2
The chart below summarizes the EXSEV bearing series
and the conditions in which each operates successfully. Table 2 EXSEV bearing lubricants
Materials and lubricants which are resistant to certain Operating Vacuum resis- Steam pressure
special conditions are listed in Tables 1 and 2. temperature tance(room at high
Major Koyo EXSEV bearing series made of these materials Lubricant Remarks
range temperature) temperature
and lubricants are listed in Table 3. ; Pa Pa
Atmospheric Not to be used when grease
Vacuum grease − 30 to + 200 −
pressure(105) to 10−5 affects operating environment.
Vacuum environment Highly resistant to chemicals
Polytetrafluoroethylene and highly insulating.
Atmospheric
resin − 100 to + 200 − Suitable when the environment
pressure to 10−5
Exsev bearings for use in a (PTFE) repeats alternation between the
Clean environment vacuum environment Insulation atmosphere and a vacuum.
Solid Friction torque is low even in a
Molybdenum Atmospheric
(MoS2) − 100 to + 300 − vacuum. Not suitable for use in
lubricant disulfide pressure to 10−5
High-temperature Exsev bearings for use in a air at high temperature.
Nonmagnetism
heated environment clean environment Low friction torque.
Lead1) (Pb) − 200 to + 300 10-3 to 10−10 10−6 (300°C)
Not suitable for use in air.
Not suitable for use in air or in
Silver1) (Ag) − 200 to + 600 10-3 to 10−10 10−5 (550°C)
Corrosive environment Ceramic bearings Light weight corrosive gas.
[Note] 1) Rolling elements or bearing rings are coated using the special ion plating method JTEKT developed.
[Remark] The lubricants in the table above are usually applied to bearings for use in a vacuum. The most suitable
one should be selected in consideration of the vacuum condition, temperature, and whether reactive gas
or inert gas exists.
Table 1 EXSEV bearing materials # Good % Fair × No good
1) 2)
Nonmagnetism
Component Operating Vacuum resistance Density Young's Coefficient Corrosion resistance Used to produce :
temperature (room temperature) modulus of linear Strong
lubrication
Vacuum Ceramic Clean
Sea water
alkali liquid
Bearing ring
Hydrogen
Insulation
Molten metal
Weak acid
Alkalescent
acid liquid
element
Shield
Bearing material range thermal

Rolling
Cage
fluoride
bearings bearings bearings
Hydrochloric
Strong
Sulfuric
Water
expansion Al
liquid
Self-
liquid
Fe
×10−6 / ;
acid
acid
; Pa g/cm3 GPa Zn
Atmospheric
Martensitic stainless steel ' ' − 250 to + 400 7.7 208 10.5 × × × % × # × × × × × × × ' ' '
pressure(105)to 10−8
Precipitation hardening Atmospheric
stainless steel ' ' − 250 to + 400 pressure to 10−8 7.8 196 11.0 × × × # % # # # # × × × × ' '
High speed tool steel ' ' − 250 to + 550 Atmospheric −8 8.5 207 12.0 × × × % × # × × × × × × × ' '
pressure to 10
Atmospheric
Ceramics (Si3N4) ' ' − 270 to + 800 pressure to 10−8 3.2 320 3.2 × # # # # # # % # # # × × '
Graphite (GF) ' + 500 max. − 2.15 − 5.5 # × # # # # # # # # # # # '
Reinforced fluorocarbon resin (FA) ' − 100 to + 200 Atmospheric

pressure to 10−6 1.9 − − # # # # # # # # # # × × # ' '
Atmospheric
Reinforced fluorocarbon resin (PT) ' − 100 to + 200 2.15 − − # # # # # # # # # # × × # '
pressure to 10−4
Reinforced PEEK resin (PN) ' − 100 to + 300 Atmospheric

pressure to 10−6 1.54 − − # # # # # # # # # # × × # ' '
Atmospheric
Austenitic stainless steel ' ' − 200 to + 300 8.0 193 16.3 × × # # # # % × × × × × × ' ' '
pressure to 10−8
(Ref.) High carbon chromium ' ' − 200 to + 120 Atmospheric 7.8 208 12.5 × × × × × × × × × × × × × —
bearing steel pressure to 10−8
[Notes] 1) A larger Young's modulus indicates higher rigidity.
2) A smaller coefficient of linear thermal expansion indicates a greater dimensional stability under heating.
C3 C4
Table 3 Koyo EXSEV bearing series models and types
4)
Exsev bearings for use in a vacuum environment Exsev bearings for use in a clean environment Ceramic bearings
Repeated alternation Repeated alternation From high vacuum Repeated alternation between Repeated alternation atmospheric pressure
Characteristics(selective points)
between atmospheric between atmospheric to ultra-high vacuum atmospheric pressure and medium between atmospheric
1) pressure and pressure and high vacuum
Vacuum resistance
medium vacuum environments vacuum environments pressure and medium
environments vacuum environments
Operating tem-
perature range, ; − 30 to + 200 − 100 to + 300 − 100 to + 350 − 200 to + 350 − 30 to + 120 − 120 to + 200 + 200 to + 260 − 100 to + 200 − 30 to + 120 + 500 max.
Cleanness (class 1005) ) − − − class 105) − − − −
Corrosion resistance 2) # # # − # " − − −
Running friction torque − Low torque Low torque − Extremely low torque − − − −
Unstable for use with Corrosion
Others − − − oxygen or corrosive gas − − − resistant nonmagnetism Insulation High temperature
MO bearing WS bearing MG bearing Clean pro Clean pro High temperature Hybrid ceramic Hybrid ceramic Hybrid ceramic Hybrid ceramic
DL bearing
PRA bearing bearing clean pro bearing bearing bearing bearing bearing
Bearing types
SV...ST SE...STMSA7 SE...STWS SE...STMG3 SE...STPRA SE...STPR SE...STPRB 3NC...MD4FA 3NC...YH4FA 3NC...FG 3NC...HT4GF
Inner ring and Precipitation Non-magnetic High carbon High speed

outer ring Martensitic stainless steel hardening chrome bearing
stainless steel stainless steel steel tool steel
Materials
Martensitic stainless steel

Rolling elements
Martensitic stainless steel Ceramics
(balls or rollers)
Austenitic Tungsten disulfide Austenitic Polyamide
Cage Austenitic stainless steel Fluorocarbon resin (FA) Graphite (GF)
stainless steel (WS) stainless steel resin
Vacuum Cage coated with Balls coated with 3)

molybdenum Self-lubrication6) Fluorocarbon-base polymeric coating Self-lubrication6) Vacuum Self-lubrication6)
Lubricant
grease disulfide(MoS2) silver(Ag) grease
Vacuum pump, P-CVD equipment for manufacture of Food or chemical Vacuum Heat roll heat
Electron beam
Applications general vacuum semiconductors and electronic parts, Semiconductor manufacturing manufacturing Motors
equipment spattering equipment epitaxial equipment equipment equipment treatment furnaces
[Notes] 1) Vacuum (pressure) is generally graded as follows : 3) These soft metals are applied by the special 5) These evaluations indicate the cleanness
Low vacuum⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅105 − 102Pa ion plating method JTEKT developed, so that around the bearing, or in the equipment interior.
Medium vacuum⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅102 − 10−1Pa they feature excellent bonding strength, Cleanness is largely dependent on the amount
High vacuum⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅10−1 − 10−5Pa extending the service life of bearings. of dirt produced by operation of the bearing.
Ultra-high vacuum⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅10−5Pa or less 4) When higher corrosion resistance, The suffixed numbers refer to amounts of dirt,
Extremely high vacuum⋅⋅⋅⋅⋅⋅⋅⋅10−8Pa or less nonmagnetism and heat resistance are and the smaller the number is, the less dirt
(Atmospheric pressure ≈ 105Pa) required, Full Ceramic Bearings should be used. produced by the bearing.
2) The corrosion resistance column shows general Please consult with JTEKT for details. [Ex.] Class 10⋅⋅⋅⋅⋅⋅⋅there are less than 10
evaluations. Ceramics can also be used to produce many particles 0.5 μm or larger in diameter in
Marks """ and "#", respectively, denote types of bearings, such as angular contact ball a 1-cubic-foot space.(as specified in
"excellent", "good", and "fair". bearings and cylindrical roller bearings. USA standards FED-STD-209D.)
Refer to Table 1 for the corrosive materials 6) Because the cage is made from self-
concerned. lubricating material.
C5 C6
■ Life of EXSEV Bearings
EXSEV bearings, lubricated with a solid lubricant, are usually used 0.1
under relatively light load conditions, such as 10% of their static load Special polymeric fluoride
ratings or less.
Equivalent load / load rating

These bearings can maintain stable performance as long as the solid 0.08
lubricant is maintained. Once the lubricant wears out, metallic contact
occurs, which increases rotational friction torque and shortens service life.
0.06
PTFE
Service life depends on use conditions. At present, it is not
possible to predict their service life under varied use conditions.
0.04
However, based on a variety of experiments and tests, JTEKT has
established an experimental formulae to predict the lives of bearings.
The formulae is described in the following subsections for reference only.
0.02
(1) Life of MG bearings consisting of silver-coated balls
0
The life of MG bearings (JTEKT serial number, SE...STMG3) can be 1 × 104 1 × 105 1 × 106 1 × 107
predicted according to the following formula; Total number of rotation to torque life
Lvh = b1 ⋅ b2 ⋅ b3 (Cv/P) q × 16 667/n ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ (1) Fig. 1 Mean life of Coated Bearings
where, (3) Ceramic bearing service life

Lvh : 90% reliable life, h
Cv : Basic dynamic load rating of vacuum-resistant ball bearings Ceramic bearings are used for a variety of pur-poses, and their specifi-
(1/13 of basic dynamic load rating of steel bearings of equal cations differ case by case. Therefore, there is no common system for
size), N estimating their service lives.
P : Dynamic equivalent load, N The estimation of full ceramic bearing service life is especially
q
: Index, q = 1 difficult at present for theoretical reasons, and requires further study.
n : Rotational speed, min−1, limited to 10 ≤ n ≤ 10 000 JTEKT estimates the full ceramic bearing service life on a case by case
b1 : Rotational speed-dependant coefficient basis according to the customer request, based on experience and experi-
b1 =1.5 × 10−3n + 1 mental data.
b2 : Material coefficient
b2 =1 (for bearings ion-plated with silver by the special ion- For hybrid ceramic bearings, in many cases the conventional equation
plating process) (2) below based on rolling contact fatigue is used to estimate service life,
b3 : Coefficient for atmospheric pressure and temperature where grease or oil can be used for lubrication and, at the same time,
b3 =1 (for 10−3 Pa and room temperature) bearings are required to be insulating and antimagnetic, or to be highly
rigid and have excellent high-speed performance.
(2) For bearings coated with PTFE or special polymeric fluoride This equation is called the corrected rated life estimation
equation. (refer to p. A 26.)
For those bearings coated with PTFE (MP7) or those coated with the
special polymeric fluoride (PR), the following formula gives their mean life Lna = a1 a2 a3 L10 = a1 a2 a3 (C/P)
p ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ (3)
for reference only. (See Fig. 3.8.)
¡In an environment where a lubricating film is formed
Lav = b2 ⋅ (Ce/P) d × 0.016667/n ⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ (2) properly, the bearing characteristic coefficient a2 is expected to be
equivalent to or larger than that of conventional steel bearings. How-
where, ever, given current conditions, coefficient a2 is counted as : a2 = 1.
Lav : Average life, h Basic dynamic load rating C is treated as being
b2 : Lubrication coefficient equivalent to that of steel bearings of the same type and
6 for bearings coated with PTFE size.
42 for bearings coated with special polymeric fluoride ¡When a satisfactory oil film is formed, the operating
Ce : 0.85 times the basic dynamic load rating of steel bearings condition coefficient a3 is counted as : a3 > 1.
of equal size, N
P : Dynamic equivalent load, N
d : Coefficient, d = 3
n : Rotational speed, min−1
C7 C8
bearing series
for use in a vacuum environment
d 4 ∼ 17 mm
B
(Refer.)
r Open type Full complement type
Designed to
r accommodate
only radial load.
uD ud
Therefore, most
suitable for high-
speed rotation.
Boundary dimensions Bearing No. (Refer.) Basicbearing

(mm) Atmospheric pressure to 10 −5 Pa 10−3 to 10−10 Pa Basic load ratings (kN)
r 1) With vacuum MoS2 coating Ag ion-plating Bearing No.
d D B Cr C0r
min. grease filled (cage) (balls)
4 10 4 0.1(0.15) SVWML 4010 ZZST SEWML 4010 ZZSTMSA7 ⎯ WML4010 0.65 0.23
4 12 4 0.2 SV 604 ZZST SE 604 ZZSTMSA7 SE 604 ZZSTMG3 604 0.97 0.36
[Note] 1) The value in ( ) shows the minimum chamfer dimension of open type bearings. If there is no indication, the
value is the same as that of the shielded type (zz).
C9 C 10
bearing series
for use in a vacuum environment
d 20 ∼ 40 mm
B
(Refer.)
r Open type Full complement type
Designed to
r accommodate
only radial load.
uD ud
Therefore, most
suitable for high-
speed rotation.

(mm) Atmospheric pressure to 10 −5 Pa 10−3 to 10−10 Pa Basic load ratings (kN)
r 1) With vacuum MoS2 coating Ag ion-plating Bearing No.
d D B Cr C0r
min. grease filled (cage) (balls)
20 47 14 1 SV 6204 ZZST SE 6204 ZZSTMSA7 SE 6204 ZZSTMG3 6204 12.8 6.65



[Note] 1) The value in ( ) shows the minimum chamfer dimension of open type bearings. If there is no indication, the
value is the same as that of the shielded type (zz).
C 11 C 12
bearing series
for use in a clean environment
d 4 ∼ (25) mm
B
uD ud
Boundary dimensions Bearing No.

(mm) <120°C <200°C <260°C
r Clean Clean Clean
d D B
min. Class10 Class10 Class10
4 12 4 0.2 SE 604 ZZSTPRA SE 604 ZZSTPR SE 604 ZZSTPRB

6 12 4 ⎯ SEWML6012-1 ZZSTPRA SEWML6012-1 ZZSTPR SEWML6012-1 ZZSTPRB

6 13 5 ⎯ SEW686 ZZSTPRA SEW686 ZZSTPR SEW686 ZZSTPRB








20 47 14 1 SE 6204 ZZSTPRA SE 6204 ZZSTPR SE 6204 ZZSTPRB
C 13 C 14
bearing series
for use in a clean environment
d (25) ∼ 40 mm
B
uD ud

(mm) <120°C <200°C <260°C
r Clean Clean Clean
d D B
min. Class10 Class10 Class10



C 15 C 16
Ceramic bearing series
d 4 ∼ 25 mm
r
uD ud

(mm) Hybrid ceramic type Full ceramic type
r High temperature For corrosion High temperature For corrosion resistance/
d D B Non magnetism Insulation
min. (up to 500°C) resistance (up to 800°C) Non magnetism/Insulation
4 12 4 0.2 ⎯ 3NC604MD4 3NC604YH4 3NC604ST4 ⎯ NC604

4 13 5 0.2 ⎯ 3NC624MD4 3NC624YH4 3NC624ST4 ⎯ NC624
5 14 5 0.2 ⎯ 3NC605MD4 3NC605YH4 3NC605ST4 ⎯ NC605

5 16 5 0.3 ⎯ 3NC625MD4 3NC625YH4 3NC625ST4 ⎯ NC625
6 17 6 0.3 3NC606HT4 GF 3NC606MD4 3NC606YH4 3NC606ST4 NC706V NC606









20 47 14 1 3NC6204HT4 GF 3NC6204MD4 3NC6204YH4 3NC6204ST4 NC7204V NC6204

C 17 C 18
Ceramic bearing series
d 30 ∼ 40 mm
r
uD ud

(mm) Hybrid ceramic type Full ceramic type
r High temperature For corrosion High temperature For corrosion resistance/
d D B Non magnetism Insulation
min. (up to 500°C) resistance (up to 800°C) Non magnetism/Insulation



C 19 C 20
Refer. Hybrid ceramic bearings (for high speed applications)
d 15 ∼ (75) mm
B B B
r r1 r r1 r
* This type of bearing is mainly
used in high speed rotating parts
r r r r such as machine tool spindles.
r1
Since rolling elements are made
uD ud uD ud uD ud of ceramics, this type of bearing
is shown here, even though not
designed as EXSEV bearing
series.
(Bearing rings are made of high
carbon chromium bearing steel)
70,72 series HAR 0,9 series NU 10 series

(mm) Cylindrical Bearing Basic load ratings Bearing Basic load ratings Bearing Basic load ratings
Angular contact ball bearings
r r1 roller bearings No. (kN) No. (kN) No. (kN)
d D B
min. min. 70,72 series HAR 0,9 series NU 10 series 70,72 Cr C0r HAR 0,9 Cr C0r NU 10 Cr C0r
15 32 9 0.3 0.15 3NC 7002 FT ⎯ ⎯ 7002 6.10 3.45 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯

15 35 11 0.6 0.3 3NC 7202 FT ⎯ ⎯ 7202 8.10 4.25 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯
20 42 12 0.6 0.3 3NC 7004 FT ⎯ ⎯ 7004 10.3 6.10 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯

20 47 14 1 0.6 3NC 7204 FT ⎯ ⎯ 7204 14.5 8.40 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯
25 47 12 0.6 0.3 3NC 7005 FT ⎯ ⎯ 7005 11.3 7.40 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯

25 52 15 1 0.6 3NC 7205 FT ⎯ ⎯ 7205 15.3 9.50 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯
30 55 13 1 0.6 3NC 7006 FT 3NC HAR006C FT ⎯ 7006 14.5 10.1 HAR006C 8.7 4.85 ⎯ ⎯ ⎯
30 62 16 1 0.6 3NC 7206 FT ⎯ ⎯ 7206 21.3 13.7 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯
35 72 17 1.1 0.6 3NC 7207 FT ⎯ ⎯ 7207 28.1 18.6 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯
40 80 18 1.1 0.6 3NC 7208 FT ⎯ ⎯ 7208 33.6 23.3 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯
50 72 12 0.6 0.3 ⎯ 3NC HAR910C FT ⎯ ⎯ ⎯ ⎯ HAR910C 9.10 6.30 ⎯ ⎯ ⎯

50 80 16 1 0.6 3NC 7010 FT 3NC HAR010C FT 3NC NU1010 FY 7010 23.6 20.1 HAR010C 11.4 7.85 NU1010 33.6 36.8
55 80 13 1 0.6 ⎯ 3NC HAR911C FT ⎯ ⎯ ⎯ ⎯ HAR911C 10.1 7.65 ⎯ ⎯ ⎯

55 90 18 1.1 0.6 3NC 7011 FT 3NC HAR011C FT 3NC NU1011 FY 7011 31.1 26.3 HAR011C 14.1 9.9 NU1011 37.4 43.8
60 85 13 1 0.6 ⎯ 3NC HAR912C FT ⎯ ⎯ ⎯ ⎯ HAR912C 9.95 7.75 ⎯ ⎯ ⎯

65 90 13 1 0.6 ⎯ 3NC HAR913C FT ⎯ ⎯ ⎯ ⎯ HAR913C 11.8 9.45 ⎯ ⎯ ⎯

70 100 16 1 0.6 ⎯ 3NC HAR914C FT ⎯ ⎯ ⎯ ⎯ HAR914C 12.9 10.5 ⎯ ⎯ ⎯

75 105 16 1 0.6 ⎯ 3NC HAR915C FT ⎯ ⎯ ⎯ ⎯ HAR915C 13.3 11.2 ⎯ ⎯ ⎯
C 21 C 22
Refer. Hybrid ceramic bearings (for high speed applications)
d (75) ∼ 120 mm
B B B
r r1 r r1 r
* This type of bearing is mainly
used in high speed rotating parts
r r r r such as machine tool spindles.
r1
Since rolling elements are made
uD ud uD ud uD ud of ceramics, this type of bearing
is shown here, even though not
designed as EXSEV bearing
series.
(Bearing rings are made of high
carbon chromium bearing steel)
70,72 series HAR 0,9 series NU 10 series

(mm) Cylindrical Bearing Basic load ratings Bearing Basic load ratings Bearing Basic load ratings
Angular contact ball bearings
r r1 roller bearings No. (kN) No. (kN) No. (kN)
d D B
min. min. 70,72 series HAR 0,9 series NU 10 series 70,72 Cr C0r HAR 0,9 Cr C0r NU 10 Cr C0r
80 110 16 1 0.6 ⎯ 3NC HAR916C FT ⎯ ⎯ ⎯ ⎯ HAR916C 13.6 11.9 ⎯ ⎯ ⎯

80 125 22 1.1 0.6 ⎯ 3NC HAR016C FT 3NC NU1016 FY ⎯ ⎯ ⎯ HAR016C 24.7 19.2 NU1016 69.3 86.4
85 120 18 1.1 0.6 ⎯ 3NC HAR917C FT ⎯ ⎯ ⎯ ⎯ HAR917C 16.3 14.2 ⎯ ⎯ ⎯

85 130 22 1.1 0.6 ⎯ 3NC HAR017C FT 3NC NU1017 FY ⎯ ⎯ ⎯ HAR017C 25.1 20.1 NU1017 71.4 91.2
90 125 18 1.1 0.6 ⎯ 3NC HAR918C FT ⎯ ⎯ ⎯ ⎯ HAR918C 16.8 15.1 ⎯ ⎯ ⎯

90 140 24 1.5 1 ⎯ 3NC HAR018C FT 3NC NU1018 FY ⎯ ⎯ ⎯ HAR018C 32.8 26.1 NU1018 84.7 109
95 130 18 1.1 0.6 ⎯ 3NC HAR919C FT ⎯ ⎯ ⎯ ⎯ HAR919C 17.3 16.0 ⎯ ⎯ ⎯

100 140 20 1.1 0.6 ⎯ 3NC HAR920C FT ⎯ ⎯ ⎯ ⎯ HAR920C 24.2 21.7 ⎯ ⎯ ⎯

105 145 20 1.1 0.6 ⎯ 3NC HAR921C FT ⎯ ⎯ ⎯ ⎯ HAR921C 24.9 23.1 ⎯ ⎯ ⎯

105 160 26 2 1 ⎯ 3NC HAR021C FT ⎯ ⎯ ⎯ ⎯ HAR021C 38.6 32.5 ⎯ ⎯ ⎯
110 150 20 1.1 0.6 ⎯ 3NC HAR922C FT ⎯ ⎯ ⎯ ⎯ HAR922C 25.1 23.8 ⎯ ⎯ ⎯

110 170 28 2 1 ⎯ 3NC HAR022C FT ⎯ ⎯ ⎯ ⎯ HAR022C 43.4 37.0 ⎯ ⎯ ⎯
120 165 22 1.1 0.6 ⎯ 3NC HAR924C FT ⎯ ⎯ ⎯ ⎯ HAR924C 29.4 28.4 ⎯ ⎯ ⎯

120 180 28 2 1 ⎯ 3NC HAR024C FT ⎯ ⎯ ⎯ ⎯ HAR024C 44.9 39.9 ⎯ ⎯ ⎯
C 23 C 24
bearing series
Linear ball bearings for vacuum
d 3 ∼ 60 mm
L
B
W W
h θ h
1
FW FW
u D u D1 ud
Clearance
Standard type adjustable type Open type
(AJ) (OP)
Shaft dia. Boundary dimensions Bearing No. Basic load ratings No. of ball rows
(mm) (mm) (kN) Clearance
Clearance Standard
d D L B W D1 h h1 θ Standard type Open type C C0 adjustable Open type
adjustable type type
type
3 7 10 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ SESDM 3 ⎯ ⎯ 69 105 4 ⎯ ⎯
4 8 12 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ SESDM 4 ⎯ ⎯ 88 127 4 ⎯ ⎯
5 10 15 10.2 1.1 9.6 ⎯ ⎯ ⎯ SESDM 5 ⎯ ⎯ 167 206 4 ⎯ ⎯
6 12 19 13.5 1.1 11.5 ⎯ ⎯ ⎯ SESDM 6 ⎯ ⎯ 206 265 4 ⎯ ⎯
8 15 17 11.5 1.1 14.3 ⎯ ⎯ ⎯ SESDM 8S ⎯ ⎯ 176 216 4 ⎯ ⎯

15 24 17.5 1.1 14.3 ⎯ ⎯ ⎯ SESDM 8 ⎯ ⎯ 274 392 4 ⎯ ⎯
10 19 29 22 1.3 18 ⎯ ⎯ ⎯ SESDM10 ⎯ ⎯ 372 549 4 ⎯ ⎯
12 21 30 23 1.3 20 1.5 8 80° SESDM12 SESDM12 AJ SESDM12 OP 510 784 4 4 3
13 23 32 23 1.3 22 1.5 9 80° SESDM13 SESDM13 AJ SESDM13 OP 510 784 4 4 3
16 28 37 26.5 1.6 27 1.5 11 80° SESDM16 SESDM16 AJ SESDM16 OP 774 1 180 4 4 3
20 32 42 30.5 1.6 30.5 1.5 11 60° SESDM20 SESDM20 AJ SESDM20 OP 882 1 370 5 5 4
25 40 59 41 1.85 38 2 12 50° SESDM25 SESDM25 AJ SESDM25 OP 980 1 570 6 6 5
30 45 64 44.5 1.85 43 2.5 15 50° SESDM30 SESDM30 AJ SESDM30 OP 1 570 2 740 6 6 5
35 52 70 49.5 2.1 49 2.5 17 50° SESDM35 SESDM35 AJ SESDM35 OP 1 670 3 140 6 6 5
40 60 80 60.5 2.1 57 3 20 50° SESDM40 SESDM40 AJ SESDM40 OP 2 160 4 020 6 6 5
50 80 100 74 2.6 76.5 3 25 50° SESDM50 SESDM50 AJ SESDM50 OP 3 820 7 940 6 6 5
60 90 110 85 3.15 86.5 3 30 50° SESDM60 SESDM60 AJ SESDM60 OP 4 700 10 000 6 6 5
C 25 C 26
K-series super thin section ball bearings
Koyo K-series super thin section ball bearings were developed to meet current engineering needs for
thinner, lighter bearings. They are used extensively in automation and labor saving equipment, such as
industrial robots.
These bearings are sorted into nine dimension series according to cross-sectional area.
Those of the same dimension series have an equivalent cross-sectional area irrespective of the bore
diameter.
They are available in three types that differ in structure.
■ Deep groove type

Carries radial load, axial
load in both directions, Bearing type code
and combined loads. C A X
(Deep groove (Angular (Four-point
type) contact type) contact type)
■ Angular contact type
Has a 30° contact angle, B B B
Dimension Cross-
and carries radial load series sectional
and axial load in one code dimension Bore
direction. E E E diameter
B=E
Two bearings are (mm)
(mm)
usually used together
facing one another.
25.4
T 4.762 KTC KTA KTX to
■ Four-point contact type 38.1
Has a contact angle of 50.8

A 6.35 KAC KAA KAX to
30° both to the right and 304.8
to the left. 50.8
to
B 7.938 KBC KBA KBX
Able to carry axial load 508
in both directions. Also
able to support moment C 9.525 KCC KCA KCX 101.6
and radial loads. to
762
D 12.7 KDC KDA KDX
F 19.05 KFC KFA KFX 101.6

to
25.4 KGA KGX 1 016
G KGC
KJA...RD
B = 11.1
J − −
E = 9.525
101.6
to
KUC...2RD KUX...2RD 304.8
B = 12.7
U −
E = 9.525
C 27 C 28
Table 1 K-series super thin section ball bearings : tolerance Unit : μm
Single plane mean bore diameter deviation Single plane mean outside diameter deviation Single inner (outer) ring Radial runout of assembled bearing ring, max. Assembled bearing ring face
runout with raceway, max.
width deviation
Bore 3 dmp 3 Dmp 3 Bs, 3 Cs Inner ring Kia Outer ring Kea Inner ring Sia Outer ring Sea Bore
diameter diameter
number classes K0, K1, K2 classes classes number
class class class classes K0, K1, K2 class class class classes classes class class K0 class classes classes class K0 class classes classes classes classes
K0, K2 K0, K2
div.1 div.2 K3 K4 K6 div.1 div.2 K3 K4 K6 K0, K1, K2 K3, K4 K6 div.1 div.2 K3 K1, K4 K2, K6 div.1 div.2 K3 K1, K4 K2, K6 K1, K4 K1, K4
K3, K6 K3, K6
0 0 0
010 − 10 − 5 0 − 4 0 0
13 8 8 010
− 5 − 8 − 5 20 10 10 5 8
0 0
015 − 13 − 8 0 0
15 10 015
− 13 − 5
020 0
5 4 8 020
13 10 13 13 8 10
0 0 − 5
025 − 15 − 10
20 25 5 025
0 0
030 − 10 − 8 030
0 0 0
035 − 8 − 15 − 8 15 15 15 035
30
040 0 0 0 Same Same 040
− 20 − 13 − 25 13 5
042
6
10 as 13 as 042
limit limit
045 values values 045
0 0 0
20 36 20 20 for for
− 20 − 13 − 10
047 radial radial 047
0
8 10 runout runout
050 − 127 8 of of 050
assem- assem-
055 0 0 0 0 bled bled 055
− 25 − 15 − 10 − 30 15
060
8 0 0 0
23 bear- bear- 060
− 25 − 15 − 10 ing ing
25 41 25
065 8 inner outer 065
ring ring
070 13 15 070
0
075 0 0 − 13 075
− 30 − 18 25
0 0 0
080 − 30 − 18 − 10 41 30 20 10 46 30 13 080
10
090 0 090
− 13
100 0 100
30 15 18
0 0 − 20 0
110 − 36 0 0 0 − 36 0 − 13 25 15 110
− 36 − 20 − 13 − 36 36 13 10 36
120 0 0
46 120
− 23 − 15 36 18 13 20
0 0 0 0
140 − 41 − 41 − 15 − 254
30 18 140
0
160 0 0 0 − 15 0 0 0 0 0 160
41 36 18 41 41 20 20 23
− 46 − 41 − 23 − 46 − 41 − 25 − 18 − 254
180 51 180
0 0 0 0 0 0
200 − 51 − 25 − 18 − 51 − 30 − 20 0
41 20 46 23 23 25 200
0 0 − 254
250 0 − 46 0 − 46 46 46 250
− 76 − 76 51
300 300
350 0 0 0 0 350
− 102 − 51 − 102 − 51 51 51
400 400
[Notes] Division 1 is for deep groove type ball bearings.
Division 2 is for angular contact type and four-point contact type ball bearings.
C 29 C 30
Table 2 Standard radil internal clearance of deep Table 3 Mounting dimensions
groove and four-point contact type ball bearings Unit : μm
Radial internal clearance

Bore
ra
diameter classes K0, K1, K2
number class K3 class K4 class K6
Deep groove Four-point
type contact type
ra
010 25 − 41 25 − 38 18 − 28 10 − 20
13 − 23
015 30 − 46 30 − 43 20 − 30 13 − 23
u Da u da
020
10 − 25
025 30 − 61 30 − 56 20 − 46
030 15 − 30
035 15 − 30
Unit : mm
040
41 − 71 41 − 66 25 − 51 u da u Da ra
042 Dimension
Bearing type
045 series
max. min. min. max. max.
20 − 36
047
T KTC KTA KTX d + 5.3 d + 3.4 d + 4.2 d + 6.1 0.2
050
055 30 − 56 A KAC KAA KAX d + 7.3 d + 4.6 d + 5.4 d + 8.2 0.4
51 − 86 51 − 76
060 20 − 36 B KBC KBA KBX d + 9.3 d + 5.7 d + 6.6 d + 10.2 0.8
065
C KCC KCA KCX d + 11.3 d + 6.9 d + 7.7 d + 12.2 0.8
070
075 25 − 41 D KDC KDA KDX d + 15.3 d + 9.2 d + 10.1 d + 16.2 1.3
36 − 61
080 61 − 107 61 − 86
F KFC KFA KFX d + 23.3 d + 13.9 d + 14.8 d + 24.2 1.8
090
100 G KGC KGA KGX d + 31.3 d + 18.7 d +19.5 d + 32.1 1.8
41 − 66
110 71 − 122 25 − 41 J − KJA −
71 − 97
120 d + 11.3 d + 6.9 d + 7.7 d + 12.2 0.2
46 − 71 30 − 46 U KUC − KUX
140 81 − 132 30 − 46
160
91 − 142 81 − 107 51 − 76 36 − 51
180
200 102 − 152 61 − 86 36 − 56
250 91 − 117
152 − 203
300
350
203 − 254 102 − 127
400
C 31 C 32
Table 4 Shaft diameter and housing bore diameter tolerance Unit : μm
Inner ring rotation Outer ring rotation

Bore Shaft diameter tolerance Housing bore diameter tolerance Shaft diameter tolerance Housing bore diameter tolerance Bore
diameter diameter
number classes K0, K1, K2 classes K0, K1, K2 classes K0, K1, K2 classes K0, K1, K2 number
class K3 class K4 class K6 class K3 class K4 class K6 class K3 class K4 class K6 class K3 class K4 class K6
div.1 div.2 div.1 div.2 div.1 div.2 div.1 div.2
+ 10 + 5 + 4 − 10 − 5 − 4
010 0 0 + 5 0 + 13 + 8 + 5 − 20 − 10 − 5 − 8 − 13 − 8 − 5 010
+ 13 + 8 0 0 0 0 − 13 − 8 − 10 − 25 − 15 − 10
015 0 0 + 13 + 5 − 25 − 15 − 13 − 5 015
0 0 − 25 − 10
020 + 5 − 5 020
+ 15 + 10 0 − 15 − 10 − 10
025 0 0 − 30 − 20 025
+ 15 + 10 + 8 − 15 − 10 − 8
030 0 0 0 − 30 − 20 − 15 030
+ 8 + 15 + 8 − 8 − 15 − 8
035 0 0 0 − 15 − 30 − 15 035
040 + 20 + 13 + 6 − 20 − 13 − 6 040
0 0 0 − 40 − 25 − 13
042 042
045 + 20 + 13 + 10 − 20 − 13 − 10 045
0 0 0 − 40 − 25 − 20
047 047
050 050
055 + 25 + 15 + 10 + 8 − 25 − 15 − 10 − 8 055
0 0 0 0 + 25 + 15 + 10 − 50 − 30 − 20 − 15 − 25 − 15 − 10
060 0 0 0 − 50 − 30 − 20 060
065 065
070 070
+ 13 − 13
075 + 30 + 18 0 − 30 − 18 − 25 075
+ 30 + 18 + 10 0 0 − 30 − 18 − 10 − 60 − 35
080 0 0 0 − 60 − 35 − 20 080
090 + 13 − 13 090
0 − 25
100 + 20 − 20 100
+ 35 + 35 0 + 13 − 35 − 35 − 40 − 13
110 0 + 35 + 20 + 13 0 + 35 0 − 70 − 35 − 20 − 13 − 70 − 35 − 25 110
0 0 0 0 − 70 − 40 − 25 − 70
120 + 23 + 15 − 23 − 15 120
+ 40 + 40 0 0 + 15 − 48 − 40 − 45 − 30 − 15
140 0 0 0 − 80 − 80 − 30 140
+ 15 − 15
160 + 45 + 40 + 23 0 + 45 + 40 + 25 + 18 − 45 − 40 − 23 − 30 − 45 − 40 − 25 − 18 160
0 0 0 0 0 0 0 − 90 − 80 − 45 − 90 − 80 − 50 − 35
180 180
+ 50 + 25 + 18 + 50 + 30 + 20 − 50 − 25 − 15 − 50 − 30 − 18
200 0 0 0 0 0 0 − 100 − 50 − 35 − 100 − 60 − 40 200
+ 45 + 45 − 45 − 45
250 + 75 0 + 75 0 − 75 − 90 − 75 − 90 250
0 0 − 150 − 150
300 300
350 + 100 + 50 + 100 + 50 − 100 − 50 − 100 − 50 350
0 0 0 0 − 200 − 100 − 200 − 100
400 400
[Notes] Division 1 is for deep groove type ball bearings.
Division 2 is for angular contact type and four-point contact type ball bearings.
C 33 C 34
open type
d 25.4 ∼ (114.3) mm
B
uD ud
Deep groove type Angular contact type Four-point contact type
Boundary dimensions Deep groove type Angular contact type Four-point contact type (Refer.) Mass
(mm) Basic load ratings Basic load ratings Basic load ratings (kg)
r Bearing Bearing Bearing Deep Angular Four-point
(kN) (kN) (kN)
d D B No. No. No. groove contact contact
min. Cr C0r Cr C0r Ca C0a Cr C0r Ca C0a type type type
25.4 34.925 4.762 0.4 KTC010 2.50 1.95 KTA010 2.65 2.20 3.45 6.70 KTX010 2.15 1.65 3.70 7.15 0.012 0.011 0.012
38.1 47.625 4.762 0.4 KTC015 2.90 2.70 KTA015 3.05 3.10 4.00 9.35 KTX015 2.50 2.30 4.20 10.5 0.018 0.017 0.018
50.8 63.5 6.35 0.6 KAC020 4.50 4.30 KAA020 4.75 4.95 6.25 14.9 KAX020 3.90 3.70 6.60 16.9 0.045 0.045 0.045
66.675 7.938 1 KBC020 6.35 5.85 KBA020 6.75 6.70 8.90 20.4 KBX020 5.55 5.00 9.35 22.0 0.073 0.068 0.073
63.5 76.2 6.35 0.6 KAC025 4.85 5.20 KAA025 5.10 5.95 6.75 18.0 KAX025 4.20 4.45 7.05 20.9 0.059 0.054 0.059
79.375 7.938 1 KBC025 6.90 7.00 KBA025 7.35 8.15 9.65 24.6 KBX025 6.00 6.00 10.0 27.3 0.086 0.086 0.086
76.2 88.9 6.35 0.6 KAC030 5.20 6.10 KAA030 5.45 7.00 7.15 21.2 KAX030 4.50 5.25 7.45 24.9 0.068 0.064 0.068
92.075 7.938 1 KBC030 7.35 8.15 KBA030 7.70 9.35 10.2 28.3 KBX030 6.35 7.00 10.6 32.5 0.109 0.100 0.109
88.9 101.6 6.35 0.6 KAC035 5.45 7.00 KAA035 5.75 8.00 7.55 24.3 KAX035 4.75 6.00 7.80 29.0 0.082 0.077 0.082
104.775 7.938 1 KBC035 7.75 9.30 KBA035 8.20 10.7 10.8 32.5 KBX035 6.70 8.00 11.1 37.8 0.122 0.122 0.122
101.6 114.3 6.35 0.6 KAC040 5.75 7.85 KAA040 6.00 9.05 7.90 27.4 KAX040 4.95 6.80 8.10 33.0 0.086 0.086 0.086
117.475 7.938 1 KBC040 8.10 10.5 KBA040 8.60 12.1 11.3 36.8 KBX040 7.05 9.00 11.6 43.1 0.136 0.136 0.136
120.65 9.525 1 KCC040 10.3 12.4 KCA040 11.2 14.9 14.7 45.1 KCX040 8.95 10.6 14.8 50.0 0.204 0.200 0.204
127 12.7 1.5 KDC040 15.7 17.2 KDA040 16.5 19.7 21.7 59.8 KDX040 13.6 14.8 22.6 67.4 0.354 0.363 0.354
139.7 19.05 2 KFC040 28.2 28.1 KFA040 30.3 32.9 39.8 99.6 KFX040 24.6 24.0 41.0 103 0.862 0.871 0.862
152.4 25.4 2 KGC040 42.6 39.6 KGA040 45.2 46.0 59.5 139 KGX040 37.3 34.5 62.4 141 1.63 1.64 1.63
107.95 120.65 6.35 0.6 KAC042 5.85 8.30 KAA042 6.15 9.55 8.10 29.0 KAX042 5.10 7.15 8.25 35.0 0.091 0.091 0.091
123.825 7.938 1 KBC042 8.25 10.9 KBA042 8.75 12.7 11.5 38.6 KBX042 7.15 9.40 11.7 45.2 0.141 0.141 0.141
127 9.525 1 KCC042 10.5 13.0 KCA042 11.5 15.8 15.1 47.8 KCX042 9.15 11.2 15.0 53.0 0.213 0.209 0.213
133.35 12.7 1.5 KDC042 15.8 17.8 KDA042 16.8 20.8 22.1 62.9 KDX042 13.7 15.3 22.8 70.2 0.376 0.381 0.376
146.05 19.05 2 KFC042 28.8 29.4 KFA042 30.6 34.0 40.3 103 KFX042 25.1 25.2 41.8 109 0.907 0.925 0.907
158.75 25.4 2 KGC042 42.2 39.9 KGA042 46.2 48.0 60.8 146 KGX042 36.9 34.3 61.8 142 1.72 1.74 1.72
114.3 127 6.35 0.6 KAC045 6.00 8.75 KAA045 6.25 10.1 8.25 30.5 KAX045 5.20 7.55 8.40 37.0 0.100 0.095 0.100
130.175 7.938 1 KBC045 8.45 11.6 KBA045 8.90 13.3 11.7 40.4 KBX045 7.35 10.0 12.0 48.3 0.150 0.154 0.150
133.35 9.525 1 KCC045 10.7 13.7 KCA045 11.7 16.6 15.4 50.4 KCX045 9.30 11.8 15.3 56.1 0.218 0.222 0.218
139.7 12.7 1.5 KDC045 16.3 19.0 KDA045 17.2 21.8 22.6 66.0 KDX045 14.2 16.3 23.4 75.5 0.399 0.399 0.399
C 35 C 36
open type
d (114.3) ∼ (165.1) mm
B
uD ud
(kN) (kN) (kN)
114.3 152.4 19.05 2 KFC045 29.4 30.8 KFA045 31.7 36.4 41.7 110 KFX045 25.6 26.3 42.6 115 0.953 0.971 0.953
165.1 25.4 2 KGC045 43.6 42.7 KGA045 47.1 50.1 62.0 152 KGX045 38.1 36.4 63.6 152 1.81 1.79 1.81
120.65 133.35 6.35 0.6 KAC047 6.10 9.20 KAA047 6.40 10.6 8.40 32.1 KAX047 5.30 7.95 8.55 39.0 0.104 0.100 0.104
136.525 7.938 1 KBC047 8.55 12.1 KBA047 9.10 14.2 12.0 42.9 KBX047 7.45 10.4 12.1 50.4 0.154 0.159 0.154
139.7 9.525 1 KCC047 10.9 14.4 KCA047 12.0 17.5 15.7 53.0 KCX047 9.50 12.4 15.5 59.1 0.227 0.231 0.227
146.05 12.7 1.5 KDC047 16.5 19.6 KDA047 17.5 22.8 23.0 69.1 KDX047 14.3 16.8 23.6 78.2 0.426 0.422 0.426
158.75 19.05 2 KFC047 29.9 32.1 KFA047 32.0 37.5 42.2 114 KFX047 26.1 27.5 43.3 121 0.998 1.03 0.998
171.45 25.4 2 KGC047 44.9 45.2 KGA047 48.0 52.1 63.1 158 KGX047 39.2 38.6 65.4 162 1.86 1.89 1.86
127 139.7 6.35 0.6 KAC050 6.20 9.65 KAA050 6.50 11.1 8.55 33.6 KAX050 5.35 8.35 8.65 41.1 0.109 0.104 0.109
142.875 7.938 1 KBC050 8.80 12.8 KBA050 9.25 14.8 12.2 44.7 KBX050 7.60 11.0 12.4 53.6 0.172 0.168 0.172
146.05 9.525 1 KCC050 11.1 15.0 KCA050 12.2 18.4 16.0 55.7 KCX050 9.65 12.9 15.8 62.1 0.263 0.245 0.263
152.4 12.7 1.5 KDC050 16.9 20.8 KDA050 17.8 23.8 23.4 72.2 KDX050 14.7 17.9 24.2 83.5 0.454 0.445 0.454
165.1 19.05 2 KFC050 30.5 33.4 KFA050 32.4 38.6 42.6 117 KFX050 26.5 28.7 44.0 127 1.04 1.08 1.04
177.8 25.4 2 KGC050 46.2 47.6 KGA050 48.8 54.2 64.3 164 KGX050 40.3 40.7 67.1 173 1.95 2.00 1.95
139.7 152.4 6.35 0.6 KAC055 6.40 10.5 KAA055 6.75 12.1 8.85 36.8 KAX055 5.55 9.10 8.90 45.1 0.113 0.113 0.113
155.575 7.938 1 KBC055 9.10 13.9 KBA055 9.60 16.2 12.6 49.0 KBX055 7.85 12.0 12.7 58.8 0.186 0.181 0.186
158.75 9.525 1 KCC055 11.5 16.4 KCA055 12.5 19.8 16.5 60.0 KCX055 10.0 14.1 16.2 68.2 0.268 0.263 0.268
165.1 12.7 1.5 KDC055 17.5 22.6 KDA055 18.4 25.9 24.2 78.5 KDX055 15.2 19.4 24.9 91.6 0.481 0.481 0.481
177.8 19.05 2 KFC055 31.5 36.1 KFA055 33.6 42.1 44.3 128 KFX055 27.4 31.0 45.3 140 1.13 1.17 1.13
190.5 25.4 2 KGC055 47.0 49.8 KGA055 50.5 58.3 66.4 177 KGX055 41.0 42.6 68.0 184 2.13 2.15 2.13
152.4 165.1 6.35 0.6 KAC060 6.60 11.4 KAA060 6.95 13.2 9.15 39.9 KAX060 5.75 9.85 9.15 49.1 0.127 0.127 0.127
168.275 7.938 1 KBC060 9.35 15.1 KBA060 9.90 17.6 13.0 53.3 KBX060 8.10 13.0 13.1 64.1 0.200 0.200 0.200
171.45 9.525 1 KCC060 11.9 17.7 KCA060 12.9 21.5 17.0 65.3 KCX060 10.3 15.3 16.7 74.2 0.286 0.290 0.286
177.8 12.7 1.5 KDC060 18.0 24.4 KDA060 19.0 27.9 24.9 84.7 KDX060 15.7 21.0 25.5 99.7 0.526 0.522 0.526
190.5 19.05 2 KFC060 32.5 38.8 KFA060 34.8 45.6 45.8 138 KFX060 28.2 33.3 46.5 152 1.22 1.23 1.22
203.2 25.4 2 KGC060 49.3 54.7 KGA060 52.0 62.4 68.4 189 KGX060 42.9 46.8 71.1 205 2.31 2.30 2.31
165.1 177.8 6.35 0.6 KAC065 6.80 12.3 KAA065 7.15 14.2 9.40 43.0 KAX065 5.90 10.6 9.40 53.2 0.136 0.136 0.136
180.975 7.938 1 KBC065 9.65 16.3 KBA065 10.1 18.8 13.3 56.9 KBX065 8.35 14.0 13.4 69.3 0.213 0.213 0.213
C 37 C 38
open type
d (165.1) ∼ 228.6 mm
B
uD ud
(kN) (kN) (kN)
165.1 184.15 9.525 1 KCC065 12.2 19.0 KCA065 13.4 23.3 17.6 70.6 KCX065 10.6 16.4 17.1 80.3 0.308 0.308 0.308
190.5 12.7 1.5 KDC065 18.6 26.1 KDA065 19.5 30.0 25.6 90.9 KDX065 16.1 22.5 26.2 108 0.553 0.562 0.553
203.2 19.05 2 KFC065 33.4 41.5 KFA065 36.0 49.1 47.3 149 KFX065 29.0 35.6 47.7 164 1.32 1.33 1.32
215.9 25.4 2 KGC065 50.0 57.0 KGA065 53.5 66.5 70.3 202 KGX065 43.5 48.8 71.8 216 2.45 2.45 2.45
177.8 190.5 6.35 0.6 KAC070 7.00 13.2 KAA070 7.35 15.2 9.65 46.1 KAX070 6.05 11.4 9.60 57.2 0.141 0.145 0.141
193.675 7.938 1 KBC070 9.90 17.4 KBA070 10.4 20.2 13.7 61.2 KBX070 8.55 15.0 13.7 74.6 0.227 0.227 0.227
196.85 9.525 1 KCC070 12.5 20.4 KCA070 13.6 24.7 17.9 74.9 KCX070 10.9 17.6 17.5 86.3 0.331 0.336 0.331
203.2 12.7 1.5 KDC070 19.0 27.9 KDA070 20.0 32.1 26.3 97.2 KDX070 16.5 24.0 26.7 116 0.594 0.603 0.594
215.9 19.05 2 KFC070 34.3 44.1 KFA070 37.0 52.6 48.7 159 KFX070 29.8 37.9 48.7 176 1.45 1.43 1.45
228.6 25.4 2 KGC070 52.1 61.8 KGA070 54.8 70.7 72.2 214 KGX070 45.3 53.0 74.5 237 2.63 2.66 2.63
190.5 203.2 6.35 0.6 KAC075 7.15 14.1 KAA075 7.50 16.2 9.90 49.2 KAX075 6.20 12.2 9.80 61.3 0.154 0.154 0.154
206.375 7.938 1 KBC075 10.1 18.6 KBA075 10.7 21.6 14.1 65.4 KBX075 8.80 16.0 14.0 79.8 0.240 0.245 0.240
209.55 9.525 1 KCC075 12.8 21.7 KCA075 14.0 26.5 18.4 80.2 KCX075 11.1 18.7 17.8 92.4 0.354 0.354 0.354
215.9 12.7 1.5 KDC075 19.5 29.7 KDA075 20.5 34.1 27.0 103 KDX075 16.9 25.6 27.3 124 0.640 0.644 0.640
228.6 19.05 2 KFC075 35.1 46.8 KFA075 37.5 54.8 49.3 166 KFX075 30.5 40.2 49.8 188 1.54 1.54 1.54
241.3 25.4 2 KGC075 52.6 64.1 KGA075 56.2 74.8 73.9 227 KGX075 45.8 55.0 75.2 249 2.77 2.81 2.77
203.2 215.9 6.35 0.6 KAC080 7.35 15.0 KAA080 7.70 17.3 10.1 52.3 KAX080 6.35 13.0 10.0 65.3 0.172 0.163 0.172
219.075 7.938 1 KBC080 10.4 19.7 KBA080 11.0 23.0 14.4 69.7 KBX080 9.00 17.0 14.3 85.1 0.259 0.259 0.259
222.25 9.525 1 KCC080 13.1 23.1 KCA080 14.4 28.2 18.9 85.5 KCX080 11.4 19.9 18.2 98.5 0.381 0.381 0.381
228.6 12.7 1.5 KDC080 20.0 31.5 KDA080 21.0 36.2 27.6 110 KDX080 17.3 27.1 27.9 132 0.694 0.689 0.694
241.3 19.05 2 KFC080 35.9 49.5 KFA080 38.5 58.3 50.6 177 KFX080 31.2 42.5 50.7 200 1.59 1.64 1.59
254 25.4 2 KGC080 54.5 69.0 KGA080 57.4 78.9 75.5 239 KGX080 47.4 59.2 77.6 270 2.95 2.97 2.95
228.6 241.3 6.35 0.6 KAC090 7.65 16.8 KAA090 8.00 19.3 10.5 58.6 KAX090 6.60 14.5 10.4 73.4 0.200 0.186 0.200
244.475 7.938 1 KBC090 10.8 22.1 KBA090 11.4 25.6 15.0 77.6 KBX090 9.35 19.1 14.8 95.6 0.299 0.290 0.299
247.65 9.525 1 KCC090 13.7 25.7 KCA090 14.9 31.4 19.6 95.1 KCX090 11.9 22.2 18.9 111 0.426 0.445 0.426
254 12.7 1.5 KDC090 20.8 35.0 KDA090 21.8 40.3 28.7 122 KDX090 18.0 30.2 28.9 148 0.780 0.767 0.780
266.7 19.05 2 KFC090 37.4 54.8 KFA090 40.3 65.3 53.1 198 KFX090 32.5 47.2 52.6 224 1.77 1.79 1.77
279.4 25.4 2 KGC090 56.8 76.1 KGA090 59.8 87.1 78.7 264 KGX090 49.4 65.3 80.5 302 3.27 3.27 3.27
C 39 C 40
open type
d 254 ∼ 406.4 mm
B
uD ud
(kN) (kN) (kN)
254 266.7 6.35 0.6 KAC100 7.95 18.6 KAA100 8.30 21.4 11.0 64.8 KAX100 6.85 16.0 10.7 81.4 0.227 0.204 0.227
269.875 7.938 1 KBC100 11.2 24.4 KBA100 11.9 28.4 15.6 86.1 KBX100 9.75 21.1 15.3 106 0.331 0.322 0.331
273.05 9.525 1 KCC100 14.2 28.4 KCA100 15.6 34.9 20.5 106 KCX100 12.3 24.5 19.5 123 0.481 0.472 0.481
279.4 12.7 1.5 KDC100 21.6 38.6 KDA100 22.7 44.4 29.8 135 KDX100 18.7 33.3 29.8 164 0.853 0.848 0.853
292.1 19.05 2 KFC100 38.8 60.2 KFA100 41.6 71.1 54.7 215 KFX100 33.7 51.8 54.3 249 1.95 2.00 1.95
304.8 25.4 2 KGC100 59.0 83.2 KGA100 62.0 95.3 81.6 289 KGX100 51.2 71.5 83.1 334 3.58 3.63 3.58
279.4 292.1 6.35 0.6 KAC110 8.20 20.3 KAA110 8.60 23.4 11.3 71.0 KAX110 7.10 17.6 11.1 89.5 0.236 0.227 0.236
295.275 7.938 1 KBC110 11.6 26.7 KBA110 12.3 31.0 16.1 94.0 KBX110 10.1 23.1 15.7 117 0.340 0.354 0.340
298.45 9.525 1 KCC110 14.7 31.1 KCA110 16.1 38.0 21.1 115 KCX110 12.7 26.8 20.1 135 0.526 0.517 0.526
304.8 12.7 1.5 KDC110 22.3 42.2 KDA110 23.4 48.5 30.8 147 KDX110 19.3 36.4 30.7 180 0.934 0.930 0.934
317.5 19.05 2 KFC110 40.2 65.5 KFA110 43.2 78.0 56.9 236 KFX110 34.8 56.4 55.9 273 2.18 2.15 2.18
330.2 25.4 2 KGC110 61.0 90.3 KGA110 64.1 104 84.3 314 KGX110 52.9 77.7 85.5 366 3.90 3.94 3.90
304.8 317.5 6.35 0.6 KAC120 8.45 22.1 KAA120 8.90 25.5 11.7 77.3 KAX120 7.35 19.1 11.4 97.6 0.254 0.245 0.254
320.675 7.938 1 KBC120 12.0 29.0 KBA120 12.7 33.8 16.7 103 KBX120 10.4 25.1 16.2 127 0.376 0.386 0.376
323.85 9.525 1 KCC120 15.2 33.8 KCA120 16.5 41.2 21.8 125 KCX120 13.1 29.2 20.6 147 0.567 0.558 0.567
330.2 12.7 1.5 KDC120 23.0 45.7 KDA120 24.2 52.6 31.8 160 KDX120 20.0 39.5 31.5 197 1.02 1.01 1.02
342.9 19.05 2 KFC120 41.4 70.9 KFA120 44.3 83.8 58.3 254 KFX120 35.9 61.1 57.4 297 2.36 2.36 2.36
355.6 25.4 2 KGC120 62.9 97.5 KGA120 66.0 112 86.9 339 KGX120 54.5 83.9 87.8 399 4.22 4.30 4.22
355.6 371.475 7.938 1 KBC140 12.7 33.7 KBA140 13.4 39.1 17.6 118 KBX140 11.0 29.1 17.0 148 0.476 0.445 0.476
374.65 9.525 1 KCC140 16.0 39.1 KCA140 17.5 47.9 23.0 145 KCX140 13.9 33.8 21.6 171 0.689 0.649 0.689
381 12.7 1.5 KDC140 24.3 52.9 KDA140 25.5 60.9 33.6 184 KDX140 21.1 45.7 33.1 229 1.24 1.17 1.24
393.7 19.05 2 KFC140 43.7 81.5 KFA140 46.8 96.5 61.6 293 KFX140 37.9 70.3 60.2 345 2.72 2.61 2.72
406.4 25.4 2 KGC140 66.3 112 KGA140 69.7 128 91.7 389 KGX140 57.5 96.2 92.0 463 4.90 4.94 4.90
406.4 422.275 7.938 1 KBC160 13.3 38.3 KBA160 14.0 44.5 18.4 135 KBX160 11.5 33.1 17.7 169 0.544 0.508 0.544
425.45 9.525 1 KCC160 16.8 44.4 KCA160 18.4 54.5 24.2 165 KCX160 14.6 38.4 22.6 195 0.785 0.739 0.785
431.8 12.7 1.5 KDC160 25.5 60.0 KDA160 26.8 69.1 35.2 209 KDX160 22.1 51.8 34.5 261 1.41 1.33 1.41
444.5 19.05 2 KFC160 45.8 92.2 KFA160 49.0 109 64.5 331 KFX160 39.7 79.6 62.7 394 3.22 3.08 3.22
457.2 25.4 2 KGC160 69.5 126 KGA160 73.0 145 96.0 439 KGX160 60.3 109 95.9 528 5.58 5.62 5.58
C 41 C 42
open type
d 457.2 ∼ 1 016 mm
B
uD ud
Boundary dimensions Deep groove type Angular contact type Four-point contact type (Refer.)Mass
(kN) (kN) (kN)
457.2 473.075 7.938 1 KBC180 13.9 42.9 KBA180 14.6 49.9 19.2 151 KBX180 12.0 37.1 18.4 190 0.612 0.572 0.612
476.25 9.525 1 KCC180 17.5 49.8 KCA180 19.2 61.2 25.3 185 KCX180 15.2 43.0 23.4 220 0.880 0.830 0.880
482.6 12.7 1.5 KDC180 26.6 67.1 KDA180 27.6 77.3 36.3 234 KDX180 23.0 58.0 35.8 293 1.58 1.49 1.58
495.3 19.05 2 KFC180 47.8 103 KFA180 51.5 123 67.7 373 KFX180 41.4 88.8 65.0 442 3.58 3.48 3.58
508 25.4 2 KGC180 72.5 140 KGA180 76.0 161 100 488 KGX180 62.8 121 99.4 592 6.21 6.26 6.21
508 523.875 7.938 1 KBC200 14.4 47.6 KBA200 15.2 55.3 20.0 168 KBX200 12.5 41.2 19.0 211 0.680 0.635 0.680
527.05 9.525 1 KCC200 18.2 55.1 KCA200 19.9 67.5 26.2 205 KCX200 15.8 47.7 24.2 244 0.980 0.921 0.980
533.4 12.7 1.5 KDC200 27.6 74.3 KDA200 29.0 85.6 38.1 259 KDX200 23.9 64.2 37.0 326 1.75 1.66 1.75
546.1 19.05 2 KFC200 49.6 114 KFA200 53.4 136 70.3 412 KFX200 43.0 98.1 67.2 491 4.04 3.84 4.04
558.8 25.4 2 KGC200 75.2 154 KGA200 78.9 178 104 538 KGX200 65.2 133 103 657 8.53 6.89 8.53
635 654.05 9.525 1 KCC250 19.7 68.5 KCA250 21.6 84.0 28.4 255 KCX250 17.1 59.2 26.0 304 1.22 1.14 1.22
660.4 12.7 1.5 KDC250 29.9 92.1 KDA250 31.4 106 41.3 322 KDX250 25.9 79.6 39.7 407 2.17 2.06 2.17
673.1 19.05 2 KFC250 53.7 140 KFA250 57.6 167 75.8 506 KFX250 46.5 121 72.0 612 4.94 4.76 4.94
685.8 25.4 2 KGC250 81.4 190 KGA250 85.4 219 112 663 KGX250 70.5 164 110 819 8.85 8.53 8.85
762 781.05 9.525 1 KCC300 21.1 81.9 KCA300 23.1 101 30.3 305 KCX300 18.3 70.8 27.6 365 1.46 1.37 1.46
787.4 12.7 1.5 KDC300 32.0 110 KDA300 33.5 127 44.1 384 KDX300 27.7 95.0 42.1 487 2.60 2.47 2.60
800.1 19.05 2 KFC300 57.3 167 KFA300 61.6 200 81.0 605 KFX300 49.6 144 76.3 733 5.90 5.67 5.90
812.8 25.4 2 KGC300 86.8 226 KGA300 91.1 260 120 788 KGX300 75.2 195 116 980 10.6 10.2 10.6
889 927.1 19.05 2 KFC350 60.6 194 KFA350 65.2 232 85.8 703 KFX350 52.5 168 80.1 854 6.85 6.62 6.85
939.8 25.4 2 KGC350 91.7 261 KGA350 96.2 301 127 912 KGX350 79.4 226 122 1 140 12.3 11.9 12.3
1 016 1 054.1 19.05 2 KFC400 63.5 221 KFA400 68.4 264 90.0 801 KFX400 55.0 191 83.6 975 7.80 7.53 7.80
1 066.8 25.4 2 KGC400 96.2 297 KGA400 101 342 133 1 040 KGX400 83.3 257 128 1 300 14.0 13.5 14.0
C 43 C 44
sealed type
d 101.6 ∼ 304.8 mm
B B1 B
uD ud

U size J size U size
(With seals) (With seal) (With seals)
r Bearing No. (kN) Bearing No. (kN) Bearing No. (kN) Deep Angular Four-point
d D B B1 groove contact contact
101.6 120.65 12.7 11.1 0.4 KUC040 2RD 10.3 12.4 KJA040 RD 11.2 14.9 14.7 45.1 KUX040 2RD 8.95 10.6 14.8 50.0 0.249 0.222 0.249
107.95 127 12.7 11.1 0.4 KUC042 2RD 10.5 13.0 KJA042 RD 11.5 15.8 15.1 47.8 KUX042 2RD 9.15 11.2 15.0 53.0 0.263 0.236 0.263
127 146.05 12.7 11.1 0.4 KUC050 2RD 11.1 15.0 KJA050 RD 12.2 18.4 16.0 55.7 KUX050 2RD 9.65 12.9 15.8 62.1 0.308 0.281 0.308
228.6 247.65 12.7 11.1 0.4 KUC090 2RD 13.7 25.7 KJA090 RD 14.9 31.4 19.6 95.1 KUX090 2RD 11.9 22.2 18.9 111 0.535 0.499 0.535
254 273.05 12.7 11.1 0.4 KUC100 2RD 14.2 28.4 KJA100 RD 15.6 34.9 20.5 106 KUX100 2RD 12.3 24.5 19.5 123 0.594 0.531 0.594
279.4 298.45 12.7 11.1 0.4 KUC110 2RD 14.7 31.1 KJA110 RD 16.1 38.0 21.1 115 KUX110 2RD 12.7 26.8 20.1 135 0.649 0.581 0.649
304.8 323.85 12.7 11.1 0.4 KUC120 2RD 15.2 33.8 KJA120 RD 16.5 41.2 21.8 125 KUX120 2RD 13.1 29.2 20.6 147 0.708 0.630 0.708
C 45 C 46
Bearings for machine tool spindles Double direction angular contact
thrust ball bearings
(for support of axial loading)
JTEKT supplies double direction angular contact thrust ball Bore diameter 25 – 340 mm
bearings and ACT type matched pair angular contact ball
bearings which are used with machine tool spindles to support
Matched pair angular contact ball
axial loading. bearing
These bearings were developed to meet needs which have (ACT type)
grown as machine tool spindle rotation has become faster and
more accurate. Bore diameter 50 – 170 mm
Several dimension series are available for selection
according to operating conditions.
For details, refer to JTEKT separate catalog "Precision Ball

and Roller Bearings for Machine Tools" (CAT. NO. B2005E).
See also the catalog for high ability bearings, CAT NO.
B2006 for High Ability Ball Bearing Series Angular Contact
Ball Bearings for Machining Tools.
(Reference)
Major bearing types which are used to carry radial
loading of machine tool spindles are shown below.
For further details, refer to the specification table
for each type.
Angular contact ball bearings Double-row cylindrical roller bearings
(for high-speed applications)
79 C 79 CPA HAR 9 C NN 30 NNU 49

70, 70 B, 70 C 70 CPA HAR 0 C NN 30 K (Tapered bore) NNU 49 K (Tapered bore)
72, 72 B, 72 C 72 CPA (high ability ball bearing)
Refer to p. B 92. for bearings with ceramic balls,

Refer to p. B 194.
refer to p. C 21.
C 47 C 48
Table 1 Bearing types for support of axial loading Table 2 Double direction angular contact thrust ball bearing tolerance
(1) Inner ring and assembled bearing width Unit : μm
Type Double direction angular contact thrust ball bearings Matched pair angular contact ball bearings
Perpendicularity of Assembled bearing
Nominal bore Actual bearing Inner ring width
Types of1) inner ring face with inner ring face
diameter 3 dmp or 3 ds1) width deviation variation
respect to the bore runout with raceway
arrangement 3 Ts VBs Sd Sia
with a d
(mm) class 5 or class 4 or classes 4 and 5, class 5 or class 4 or class 5 or class 4 or class 5 or class 4 or
double-row
equivalent equivalent or equivalent equivalent equivalent equivalent equivalent equivalent equivalent
cylindrical
roller bearing over up to upper lower upper lower upper lower max. max. max.
60° 40° 30°
18 30 0 − 6 0 − 5 0 − 300 5 2.5 8 4 5 3
30 50 0 − 8 0 − 6 0 − 400 5 3 8 4 5 3
Diameter 50 80 0 − 9 0 − 7 0 − 500 6 4 8 4 6 5
series 80 120 0 − 10 0 − 8 0 − 600 7 4 9 5 6 5
2344 B ACT 0 B DB ACT 0 DB q 120 180 0 − 13 0 − 10 0 − 700 8 5 10 6 8 6
0 180 250 0 − 15 0 − 12 0 − 800 10 6 11 7 8 6
2347 B ––– ––– w
250 315 0 − 18 0 − 15 0 − 900 13 7 13 8 10 8
2394 B ––– ––– e 315 400 0 − 23 0 − 18 0 − 1 000 15 9 15 9 13 10
9
2397 B ––– ––– r
(2) Outer ring Unit : μm
Characteristics ¡Supports axial loading in both directions. ¡For support of axial loading only.
Perpendicularity of outer Assembled bearing
Highly rigid in the axial direction. Negative tolerances are specified for the Nominal outside Outer ring width variation ring outside surface with outer ring face runout
¡Bearings with a larger contact angle outside diameter. diameter 3 Dmp or 3 Ds2)
respect to the face with raceway
feature higher rigidity, while those with a ¡Excellent high-speed performance is VCs SD Sea
––– D
smaller contact angle feature better achieved
(mm) classes 5 and 4, class 5 or class 4 or class 5 or class 4 or classes 5 and 4,
high-speed performance. because of the small contact angle. or equivalent equivalent equivalent equivalent equivalent or equivalent
¡Interchangeable with 2344 B series
over up to upper lower max. max. max.
bearings. 2)
30 50 − 30 − 40 5 2.5 8 4
50 80 − 40 − 50 6 3 8 4
[Notes] 80 120 − 50 − 60 8 4 9 5
1) These bearings are usually used in arrangement with a double- Shall conform
120 150 − 60 − 75 8 5 10 5
row cylindrical roller bearing which carries a radial load. to the tolerance
C1 150 180 − 60 − 75 8 5 10 5
There are four arrangement types ( q to r) as follows : Sia on d of the
180 250 − 75 − 90 10 7 11 7
same bearing
q Mounted with an NN30K tapered bore bearing or with an NN30 250 315 − 90 − 105 11 7 13 8
cylindrical bore bearing. The tapered bore bearing is combined Spacer A 315 400 − 110 − 125 13 8 13 10
at its smaller side. 400 500 − 120 − 140 15 10 15 13
w Mounted with an NN30K tapered bore bearing, which is [Notes] 1) Single plane mean bore diameter deviation or single bore diameter deviation
combined at its larger side. 2B 2) Single plane mean outside diameter deviation or single outside diameter deviation
e Mounted with an NNU49K tapered bore bearing or with an
NNU49 cylindrical bore bearing. The tapered bore bearing is
combined at its smaller side. Spacer A' Table 3 ACT 0 series angular contact ball bearing outside diameter tolerance Unit : μm
r Mounted with an NNU49K tapered bore bearing, which is
combined at its larger side. Nominal outside diameter D (mm) Single outside diameter deviation 3 Ds
2) The overall width "2 B" of ACT0 DB and ACT0B DB bearings is over up to upper lower
equivalent to dimension " C1" of 2344B bearings. Therefore, 50 80 − 32 − 47
when a 2344B bearing is replaced with an ACT0 DB or ACT0B DB 80 120 − 39 − 56
bearing, change the width of spacer "A" only. 120 150 − 44 − 66
No change is necessary to the spindle or housing dimensions. 150 180 − 44 − 68
180 250 − 51 − 79
250 315 − 56 − 89
[Remark] Refer to JIS B 1514 "radial bearing tolerance" class 4 and class 5 (pp. A 54 to A 57,
Table 7-3) for the accuracy of dimensions other than outside diameter and for running
accuracy.
C 49 C 50
[Reference] Axial load and axial displacement
The relationship between axial loading and the axial displacement of double direction angular contact
thrust ball bearings and ACT type angular contact ball bearings is shown below :
(3) ACT000 (contact angle 30°) (4) ACT000B (contact angle 40°)
(1) 234400B, 234700B (contact angle 60°) (2) 239400B, 239700B (contact angle 60°) a) When preload L is applied a) When preload L is applied
8 Bore dia. 5 Bore dia. 14 Bore dia. 8 Bore dia.
No. No. No. No.
10
7 10 7
08 12
20
Amount of axial displacement (μm)


4 11 11
12 6
6
10 12
13
13
5 15 5
3
10,12 8 14
30
4 4 16
18
14 6 20 18
2 40 20
3 16,18 22 3
22
24,26
20,24 26
60 4 28
30 30 28
2 2 32
34 34
1
2
1 1
0 0 0 0
0 0.5 1 1.5 2 2.5 3 3.5 0 0.5 1 1.5 2 2.5 3 3.5 4 0 0.5 1 1.5 2 2.5 0 0.5 1 1.5 2 2.5
Axial load (kN) Axial load (kN) Axial load (kN) Axial load (kN)
b) When preload M is applied b) When preload M is applied

12 Bore dia. 6 Bore dia.
No. No.
10
10
10 5

11
11
12
12
8 4 13
13
14
15 16
6 3
18
18 20
20 22
4 22 2 26
24, 26
28
28 34
30
34
2 1
0 0
0 0.5 1 1.5 2 2.5 0 0.5 1 1.5 2 2.5
Axial load (kN) Axial load (kN)
C 51 C 52
Double direction angular contact thrust ball bearings
d 25 ∼ 105 mm
T
w rb
r1 u d0
r ra
B
u D u EW u d u d1 u Da u da
Boundary dimensions Basic load ratings Limiting speeds Bearing No. Dimensions Mounting dimensions (Refer.)Mass
Amount of
d (mm) (kN) (min−1) (mm) (mm) (kg)
grease fill
Small bore Large bore r r1 Grease Small bore Large bore da Da ra rb Small bore Large bore
D T C Ca C0a Oil lub. Ew 1) d1 B d0 w (cm3/row)
type type min. min. lub. type type min. max. max. max. type type
25 ⎯ 47 28 14 0.6 0.3 13.2 19.9 7 700 11 000 234405B ⎯ 41.3 40 7 2 4.5 33 44 0.6 0.3 0.18 ~ 0.26 0.194 ⎯
30 32 55 32 16 1 0.6 14.0 23.6 6 700 9 500 234406B 234706B 48.5 47 8 2 4.5 40 50.5 1 0.6 0.30 ~ 0.45 0.296 0.272
35 37 62 34 17 1 0.6 20.8 34.8 6 100 8 700 234407B 234707B 55 53 8.5 2 4.5 45.5 57.5 1 0.6 0.40 ~ 0.60 0.388 0.357
40 42 68 36 18 1 0.6 23.9 41.7 5 700 8 100 234408B 234708B 61 58.5 9 2 4.5 50 63.5 1 0.6 0.50 ~ 0.75 0.475 0.437
45 47 75 38 19 1 0.6 26.0 50.1 5 200 7 500 234409B 234709B 67.5 65 9.5 2 4.5 56.5 70.5 1 0.6 0.65 ~ 0.98 0.602 0.554
50 52 80 38 19 1 0.6 26.8 54.4 5 100 7 300 234410B 234710B 72.5 70 9.5 2 4.5 61.5 75.5 1 0.6 0.70 ~ 1.1 0.654 0.602
55 57 90 44 22 1.1 0.6 37.2 71.7 4 400 6 400 234411B 234711B 81 78 11 4 8 67.5 84 1 0.6 1.0 ~ 1.5 0.978 0.900
60 62 95 44 22 1.1 0.6 37.6 75.2 4 300 6 200 234412B 234712B 86.1 83 11 4 8 72.5 89 1 0.6 1.1 ~ 1.7 1.04 0.957
65 67 100 44 22 1.1 0.6 39.0 81.8 4 200 6 000 234413B 234713B 91 88 11 4 8 77.5 94 1 0.6 1.2 ~ 1.7 1.11 1.02
70 73 110 48 24 1.1 0.6 47.5 103 3 800 5 500 234414B 234714B 100 97 12 4 8 85 104 1 0.6 1.7 ~ 2.5 1.52 1.40
75 78 115 48 24 1.1 0.6 49.1 111 3 700 5 300 234415B 234715B 105 102 12 4 8 90 109 1 0.6 1.8 ~ 2.6 1.62 1.49
80 83 125 54 27 1.1 0.6 57.6 132 3 400 4 800 234416B 234716B 113 110 13.5 4 8 96.5 119 1 0.6 2.4 ~ 3.6 2.19 2.03
85 88 130 54 27 1.1 0.6 58.2 137 3 300 4 700 234417B 234717B 118 115 13.5 4 8 102 124 1 0.6 2.5 ~ 3.8 2.30 2.12
90 93 140 60 30 1.5 1 67.4 160 3 000 4 300 234418B 234718B 127 123 15 4 8 109 133.5 1.5 1 3.3 ~ 4.9 3.03 2.79
95 98 145 60 30 1.5 1 68.0 166 3 000 4 200 234419B 234719B 132 128 15 4 8 114 138.5 1.5 1 3.4 ~ 5.0 3.17 2.92
100 ⎯ 140 48 24 1.1 0.6 52.2 135 2 800 3 800 239420B ⎯ 131 126 12 4 8 114 134 1 0.6 3.1 ~ 4.6 2.08 ⎯
100 103 150 60 30 1.5 1 68.7 172 2 900 4 100 234420B 234720B 137 133 15 4 8 119 143.5 1.5 1 3.4 ~ 5.1 3.33 3.06
105 ⎯ 145 48 24 1.1 0.6 53.6 143 2 700 3 800 239421B ⎯ 136 131 12 4 8 119 139 1 0.6 3.1 ~ 4.6 2.16 ⎯
105 109 160 66 33 2 1 78.8 199 2 700 3 800 234421B 234721B 146 142 16.5 6 12 127 152 2 1 4.7 ~ 7.1 4.15 3.82
[Note] 1) The dimension E w is used as a reference for the ball set outside diameter.
C 53 C 54
d 110 ∼ (240) mm
T
w rb
r1 u d0
r ra
B
Amount of
grease fill
110 ⎯ 150 48 24 1.1 0.6 53.9 148 2 700 3 700 239422B ⎯ 141 136 12 4 8 124 144 1 0.6 3.0 ~ 4.5 2.25 ⎯
110 114 170 72 36 2 1 95.9 235 2 500 3 500 234422B 234722B 155 150 18 6 12 133 162 2 1 5.9 ~ 8.8 5.38 4.95
120 124 165 54 27 1.1 0.6 64.9 185 2 400 3 300 239424B 239724B 154.5 150 13.5 4 8 138 160 1 0.6 4.2 ~ 6.3 3.12 2.81
120 124 180 72 36 2 1 98.3 252 2 400 3 400 234424B 234724B 165 160 18 6 12 143 172 2 1 6.4 ~ 9.5 5.77 5.31
130 134 180 60 30 1.5 1 75.0 217 2 100 3 000 239426B 239726B 168 163 15 4 8 150 172 1.5 1 5.8 ~ 8.7 4.19 3.77
130 135 200 84 42 2 1 139 340 2 100 3 000 234426B 234726B 182 177 21 6 12 155 192 2 1 9.3 ~ 13.9 8.63 7.94
140 144 190 60 30 1.5 1 75.9 229 2 100 2 900 239428B 239728B 178 173 15 4 8 160 182 1.5 1 6.3 ~ 9.4 4.47 4.03
140 145 210 84 42 2 1 144 366 2 000 2 900 234428B 234728B 192 187 21 6 12 165 202 2 1 9.7 ~ 14.5 9.18 8.44
150 155 210 72 36 2 1 107 312 1 800 2 500 239430B 239730B 196.5 190 18 4 8 174 200 2 1 9.6 ~ 14.4 7.01 6.31
150 155 225 90 45 2.1 1.1 147 394 1 900 2 700 234430B 234730B 206 200 22.5 6 14 178 215 2 1 12.0 ~ 17.9 11.3 10.4
160 165 220 72 36 2 1 109 329 1 700 2 400 239432B 239732B 206.5 200 18 4 8 184 210 2 1 9.3 ~ 14.0 7.40 6.66
160 165 240 96 48 2.1 1.1 173 460 1 700 2 500 234432B 234732B 219 212 24 6 14 189 230 2 1 14.1 ~ 21.1 13.3 12.2
170 175 230 72 36 2 1 111 346 1 700 2 300 239434B 239734B 216.5 210 18 4 8 194 220 2 1 10.8 ~ 16.2 7.79 7.01
170 176 260 108 54 2.1 1.1 203 547 1 600 2 200 234434B 234734B 236 230 27 6 14 203 250 2 1 18.6 ~ 27.8 18.1 16.6
180 186 250 84 42 2 1 157 460 1 500 2 100 239436B 239736B 234 227 21 4 8 207 240 2 1 14.9 ~ 22.3 11.3 10.2
180 187 280 120 60 2.1 1.1 234 642 1 400 2 000 234436B 234736B 255 248 30 8 16 219 270 2 1 23.4 ~ 35.1 24.9 22.9
190 196 260 84 42 2 1 157 474 1 400 2 000 239438B 239738B 242 237 21 4 8 217 250 2 1 15.7 ~ 23.5 11.9 10.7
190 197 290 120 60 2.1 1.1 237 665 1 400 1 900 234438B 234738B 265 258 30 8 16 229 280 2 1 24.7 ~ 37.1 25.0 23.0
200 207 280 96 48 2.1 1.1 185 557 1 300 1 800 239440B 239740B 259 252 24 4 8 231 268 2 1 23.5 ~ 35.2 16.6 14.9
200 207 310 132 66 2.1 1.1 279 771 1 200 1 800 234440B 234740B 282 274 33 8 16 243 300 2 1 31.8 ~ 47.7 32.1 29.5
220 227 300 96 48 2.1 1.1 191 606 1 200 1 700 239444B 239744B 280 272 24 6 12 251 288 2 1 24.7 ~ 37.0 18.0 16.2
220 228 340 144 72 3 1.1 334 939 1 100 1 600 234444B 234744B 310 304 36 12 22 267 330 2.5 1 43.0 ~ 64.4 42.0 38.6
240 247 320 96 48 2.1 1.1 196 655 1 200 1 600 239448B 239748B 299 292 24 6 12 271 308 2 1 26.4 ~ 39.5 19.1 17.2
C 55 C 56
d (240) ∼ 340 mm
T
w rb
r1 u d0
r ra
B
Amount of
grease fill
240 248 360 144 72 3 1.1 342 1 010 1 100 1 500 234448B 234748B 330 322 36 12 22 287 350 2.5 1 47.7 ~ 71.6 45.0 41.4
260 269 360 120 60 2.1 1.1 261 869 950 1 300 239452B 239752B 335 328 30 6 12 299 344 2 1 43.7 ~ 65.5 33.5 30.2
260 269 400 164 82 4 1.5 406 1 270 920 1 300 234452B 234752B 364 354 41 12 22 315 388 3 1.5 67.0 ~ 101 65.8 60.5
280 289 380 120 60 2.1 1.1 265 915 910 1 300 239456B 239756B 356 348 30 6 14 319 363 2 1 49.1 ~ 73.7 35.7 32.1
280 289 420 164 82 4 1.5 417 1 360 880 1 300 234456B 234756B 384 374 41 12 22 335 408 3 1.5 73.5 ~ 110 69.8 64.2
300 310 420 144 72 3 1.1 352 1 150 770 1 100 239460B 239760B 391 384 36 6 14 349 398 2.5 1 71.5 ~ 107 56.1 50.5
300 310 460 190 95 4 1.5 476 1 630 760 1 100 234460B 234760B 418 406 47.5 12 22 364 448 3 1.5 98.0 ~ 147 100 91.8
320 330 440 144 72 3 1.1 361 1 220 740 1 000 239464B 239764B 408 404 36 6 14 369 419 2.5 1 81.5 ~ 122 59.2 53.3
320 330 480 190 95 4 1.5 479 1 680 730 1 000 234464B 234764B 438 426 47.5 12 22 384 468 3 1.5 108 ~ 162 106 97.5
340 ⎯ 460 144 72 3 1.1 368 1 290 710 980 239468B ⎯ 428 424 36 8 16 389 438 2.5 1 84.5 ~ 127 63.1 ⎯
C 57 C 58
Matched pair angular contact ball bearings
d 30 ∼ 85 mm
2B
r1 r1 rb
r r ra
uD ud u Da u da
Boundary dimensions Basic load ratings Limiting speeds Permissble Mounting dimensions (Refer.)
(mm) (kN) (min−1) (mm) Envelope
axial loads Mass
r r1 Bearing No. 1) da Da ra rb volume
(kN) (kg/row)
d D 2B
min. min.
Ca C0a Grease lub. Oil lub.
min. max. max. max.
(cm3/row)
(static)
30 55 24 1 0.6 15.1 26.6 15 000 20 000 ACT006DB 2.92 41 50 1 0.6 3.0 0.235
30 55 24 1 0.6 18.1 30.5 13 000 18 000 ACT006BDB 9.86 41 50 1 0.6 3.0 0.235
35 62 25.5 1 0.6 15.8 30.2 13 000 17 000 ACT007DB 3.25 46 57 1 0.6 4.2 0.312
35 62 25.5 1 0.6 18.9 34.5 12 000 15 000 ACT007BDB 10.9 46 57 1 0.6 4.2 0.312
40 68 27 1 0.6 16.5 33.8 12 000 15 000 ACT008DB 3.58 51 63 1 0.6 5.0 0.391
40 68 27 1 0.6 19.6 37.7 11 000 14 000 ACT008BDB 12.1 51 63 1 0.6 5.0 0.391
45 75 28.5 1 0.6 18.4 38.6 11 000 14 000 ACT009DB 3.84 56 70 1 0.6 5.7 0.536
45 75 28.5 1 0.6 21.8 42.7 9 500 13 000 ACT009BDB 13.2 56 70 1 0.6 5.7 0.536
50 80 28.5 1 0.6 19.1 41.7 9 700 13 000 ACT010DB 4.20 61 75 1 0.6 8.0 0.551
50 80 28.5 1 0.6 22.7 46.3 8 800 12 000 ACT010BDB 14.5 61 75 1 0.6 8.0 0.551
55 90 33 1.1 0.6 23.7 52.8 8 700 11 000 ACT011DB 5.63 68 84 1 0.6 12 0.831
55 90 33 1.1 0.6 28.1 58.6 7 900 10 000 ACT011BDB 19.0 68 84 1 0.6 12 0.831
60 95 33 1.1 0.6 24.6 56.9 8 100 11 000 ACT012DB 6.11 73 89 1 0.6 13 0.887
60 95 33 1.1 0.6 29.1 63.1 7 400 9 700 ACT012BDB 20.6 73 89 1 0.6 13 0.887
65 100 33 1.1 0.6 25.4 60.9 7 600 10 000 ACT013DB 6.59 78 94 1 0.6 14 0.943
65 100 33 1.1 0.6 30.1 67.6 6 900 9 000 ACT013BDB 22.2 78 94 1 0.6 14 0.945
70 110 36 1.1 0.6 34.8 82.1 7 000 9 200 ACT014DB 8.39 85 104 1 0.6 16 1.33
70 110 36 1.1 0.6 41.3 91.1 6 300 8 300 ACT014BDB 28.8 85 104 1 0.6 16 1.33
75 115 36 1.1 0.6 35.3 84.9 6 600 8 700 ACT015DB 8.74 90 109 1 0.6 20 1.35
75 115 36 1.1 0.6 41.8 94.2 6 000 7 800 ACT015BDB 30.0 90 109 1 0.6 20 1.35
80 125 40.5 1.1 0.6 41.3 101 6 100 8 000 ACT016DB 10.8 97 118 1 0.6 27 1.86
80 125 40.5 1.1 0.6 49.1 112 5 500 7 200 ACT016BDB 36.6 97 118 1 0.6 27 1.86
85 130 40.5 1.1 0.6 41.9 105 5 800 7 600 ACT017DB 11.2 102 123 1 0.6 29 1.94
85 130 40.5 1.1 0.6 49.7 116 5 200 6 900 ACT017BDB 38.0 102 123 1 0.6 29 1.94
[Note] 1) B and no indication before matching code in bearing numbers represent nominal contact angle of 40° and 30 °
respectively.
C 59 C 60
d 90 ∼ 180 mm
2B
r1 r1 rb
r r ra
uD ud u Da u da
axial loads Mass
(kN) (kg/row)
d D 2B
min. min.
min. max. max. max.
(cm3/row)
(static)
90 140 45 1.5 1 55.0 138 5 400 7 100 ACT018DB 14.2 109 132 1.5 1 39 2.55
90 140 45 1.5 1 65.3 153 4 900 6 400 ACT018BDB 48.7 109 132 1.5 1 39 2.55
95 145 45 1.5 1 55.8 143 5 200 6 800 ACT019DB 14.8 114 137 1.5 1 40 2.62
95 145 45 1.5 1 66.3 159 4 700 6 200 ACT019BDB 50.6 114 137 1.5 1 40 2.62
100 150 45 1.5 1 56.6 148 5 000 6 500 ACT020DB 15.3 119 143 1.5 1 42 2.77
100 150 45 1.5 1 67.2 164 4 500 5 900 ACT020BDB 52.5 119 143 1.5 1 42 2.77
105 160 49.5 2 1 64.4 170 4 700 6 100 ACT021DB 18.2 125 151 2 1 50 3.61
105 160 49.5 2 1 76.4 188 4 200 5 500 ACT021BDB 63.2 125 151 2 1 50 3.61
110 170 54 2 1 72.4 193 4 400 5 800 ACT022DB 19.6 132 160 2 1 64 4.52
110 170 54 2 1 86.0 214 4 000 5 200 ACT022BDB 71.3 132 160 2 1 64 4.52
120 180 54 2 1 74.6 206 4 100 5 400 ACT024DB 21.0 142 170 2 1 69 4.83
120 180 54 2 1 88.4 228 3 700 4 900 ACT024BDB 76.4 142 170 2 1 69 4.83
130 200 63 2 1 94.2 253 3 700 4 800 ACT026DB 25.9 156 188 2 1 106 7.21
130 200 63 2 1 112 281 3 300 4 400 ACT026BDB 93.0 156 188 2 1 106 7.21
140 210 63 2 1 102 290 3 400 4 500 ACT028DB 29.9 166 198 2 1 110 7.69
140 210 63 2 1 121 323 3 100 4 100 ACT028BDB 107 166 198 2 1 110 7.65
150 225 67.5 2.1 1.1 120 344 3 200 4 200 ACT030DB 34.7 178 213 2 1 138 9.39
150 225 67.5 2.1 1.1 143 382 2 900 3 800 ACT030BDB 125 178 213 2 1 138 9.39
160 240 72 2.1 1.1 130 377 3 000 3 900 ACT032DB 39.1 190 227 2 1 167 11.4
160 240 72 2.1 1.1 155 419 2 700 3 500 ACT032BDB 139 190 227 2 1 167 11.4
170 260 81 2.1 1.1 153 449 2 700 3 600 ACT034DB 45.7 204 245 2 1 221 15.7
170 260 81 2.1 1.1 181 499 2 500 3 200 ACT034BDB 163 204 245 2 1 221 15.7
180 280 90 2.1 1.1 173 510 2 500 3 300 ACT036DB 54.0 216 264 2 1 313 22.2
180 280 90 2.1 1.1 205 566 2 300 3 000 ACT036BDB 183 216 264 2 1 313 22.2
respectively.
C 61 C 62
d 190 ∼ 320 mm
2B
r1 r1 rb
r r ra
uD ud u Da u da
axial loads Mass
(kN) (kg/row)
d D 2B
min. min.
min. max. max. max.
(cm3/row)
(static)
190 290 90 2.1 1.1 179 544 2 400 3 100 ACT038DB 57.9 226 275 2 1 329 23.0
190 290 90 2.1 1.1 213 604 2 200 2 800 ACT038BDB 196 226 275 2 1 329 23.0
200 310 99 2.1 1.1 215 633 2 200 2 900 ACT040DB 64.8 240 293 2 1 421 29.5
200 310 99 2.1 1.1 255 702 2 000 2 600 ACT040BDB 229 240 293 2 1 421 29.5
220 340 108 3 1.1 252 773 2 000 2 600 ACT044DB 81.9 263 321 2.5 1 566 38.5
220 340 108 3 1.1 299 858 1 800 2 400 ACT044BDB 278 263 321 2.5 1 566 38.5
240 360 108 3 1.1 260 823 1 800 2 400 ACT048DB 87.9 283 343 2.5 1 605 41.1
240 360 108 3 1.1 308 914 1 600 2 200 ACT048BDB 298 283 343 2.5 1 605 41.1
260 400 123 4 1.5 321 1 090 1 600 2 100 ACT052DB 111 310 379 3 1.5 866 60.5
260 400 123 4 1.5 381 1 210 1 500 1 900 ACT052BDB 393 310 379 3 1.5 866 60.5
280 420 123 4 1.5 332 1 160 1 500 2 000 ACT056DB 119 330 401 3 1.5 915 64.1
280 420 123 4 1.5 393 1 290 1 400 1 800 ACT056BDB 421 330 401 3 1.5 915 64.1
300 460 142.5 4 1.5 375 1 370 1 300 1 800 ACT060DB 143 358 435 3 1.5 1 320 92.1
300 460 142.5 4 1.5 444 1 530 1 200 1 600 ACT060BDB 501 358 435 3 1.5 1 320 92.1
320 480 142.5 4 1.5 378 1 420 1 200 1 600 ACT064DB 148 378 457 3 1.5 1 400 96.9
320 480 142.5 4 1.5 449 1 570 1 100 1 500 ACT064BDB 518 378 457 3 1.5 1 400 96.9
respectively.
C 63 C 64
Precision ball screw support Support bearings
bearings and bearing units

Bore diameter 17 – 60 mm
■ Support bearings were developed to support precision ball
screw shafts. They have the same structure as angular Support bearing units
contact thrust ball bearings with a contact angle of 60°.
¡Have a large axial load
carrying capacity. Also able
to carry a certain degree of
60° radial load.
¡Highly rigid in the axial
direction.
¡Starting torque is small.
■ Support bearing units consist of the bearings described above and a precisely processed housing.
Units with a Koyo precision ball screw are also available.
■ For details, refer to JTEKT separate catalog "Precision Ball and Roller Bearings for Machine Tools"
(CAT. NO. B2005E).
Table 1 Support bearing tolerance

(1) Inner ring Unit : μm
Single plane mean Single bore Single inner Inner ring Radial Perpendicu- Assembled
Nominal bore diameter diameter deviation ring width width runout of larity of bearing
deviation deviation variation assembled inner ring inner ring
bore bearing face with face runout
diameter inner ringrespect to with
the bore raceway
d 3 dmp 3 ds 3 Bs VBs Kia Sd Sia
(mm)
classes class class class class class class class class
class 5Z class 4Z class 5Z class 4Z 5Z, 4Z 5Z 4Z 5Z 4Z 5Z 4Z 5Z 4Z
over up to upper lower upper lower upper lower upper lower upper lower max. max. max. max.
10 18 0 − 5 0 − 4 0 − 5 0 − 4 0 − 80 5 2.5 4 2.5 7 3 5 3
18 30 0 −6 0 −5 0 −6 0 −5 0 − 120 5 2.5 4 3 8 4 5 3
30 50 0 −8 0 −6 0 −8 0 −6 0 − 120 5 3 5 4 8 4 6 3
50 80 0 −9 0 −7 0 −9 0 −7 0 − 150 6 4 5 4 8 5 7 4
(2) Outer ring Unit : μm

Single plane mean Single outside Single Outer ring Radial Perpendicu- Assembled
Nominal outside diameter diameter deviation outer width runout of larity of outer bearing
deviation ring width variation assembled ring outside outer
outside deviation bearing surface with ring face
diameter outer ring respect to runout with
the face raceway
D 3 Dmp 3 Ds 3 Cs VCs Kea SD Sea
(mm)
classes class class class class class class class class
class 5Z class 4Z class 5Z class 4Z 5Z, 4Z 5Z 4Z 5Z 4Z 5Z 4Z 5Z 4Z
over up to upper lower upper lower upper lower upper lower upper lower max. max. max. max.
30 50 0 − 7 0 −6 0 − 7 0 − 6 Equivalent to 5 2.5 7 5 8 4 Equivalent to
3 tolerances Sia tolerances
50 80 0 − 9 0 −7 0 − 9 0 − 7 Bs 6 3 8 5 8 4
of a bearing of of a bearing of
80 120 0 − 10 0 −8 0 − 10 0 − 8 the same d 8 4 10 6 9 5 the same d
C 65 C 66
Precision ball screw support bearings
d 17 ∼ 60 mm
B
r r1
DB DBD DBB DBT
r1 r
u D u D1 u d1 u d u d2 u D 2 DFT
DF DFD DFF
DT DTD
Boundary dimensions Basic dynamic Max. axial loadings Limiting speeds Dimensions Standard preload (kN) Starting torque (mN⋅m) Axial rigidity (N/μm) (Refer.)
Envelope
(mm) load rating 1) (kN) (min−1) (mm) Matching types Matching types Matching types Mass
Bearing No. 2) volume
r r1 Ca Single- Double- Triple- Grease Two Three Four Two Three Four Two Three Four (kg/row)
d D B
(kN)
Oil lub. (cm3/row) d1 d2 D1 D2
min. min. row row row lub. bearings bearings bearings bearings bearings bearings bearings bearings bearings
17 47 15 1 0.6 26.0 34.3 68.6 103 6 300 8 000 SAC1747B 3.7 25.5 33.7 33.5 41 2.15 2.92 4.30 140 180 280 695 1 030 1 390 0.13
20 47 15 1 0.6 26.0 34.3 68.6 103 6 300 8 000 SAC2047B 3.7 26.8 33.7 33.5 41 2.15 2.92 4.30 140 180 280 695 1 030 1 390 0.12
25 62 15 1 0.6 30.2 48.1 96.2 144 4 600 6 000 SAC2562B 4.9 38 46.2 46 53.5 3.04 4.13 6.08 200 260 400 970 1 440 1 940 0.24
30 62 15 1 0.6 30.2 48.1 96.2 144 4 600 6 000 SAC3062B 4.9 38 46.2 46 53.5 3.04 4.13 6.08 200 260 400 970 1 440 1 940 0.21
35 72 15 1 0.6 32.8 58.8 118 176 3 700 5 000 SAC3572B 6.2 48 56.3 55.9 63.5 3.73 5.07 7.46 240 320 480 1 180 1 760 2 360 0.29
40 72 15 1 0.6 32.8 58.8 118 176 3 700 4 800 SAC4072B 6.2 48 56.3 55.9 63.5 3.73 5.07 7.46 240 320 480 1 180 1 760 2 360 0.26
40 90 20 1 0.6 65.4 122 244 366 3 100 4 000 SAC4090B 15 54.5 67.5 66.8 78.5 5.00 6.80 10.0 440 610 880 1 270 1 890 2 540 0.62
45 75 15 1 0.6 34.0 64.4 129 193 3 400 4 300 SAC4575B 6.9 54 61.7 61.5 69 3.89 5.29 7.78 250 330 500 1 270 1 890 2 540 0.25
45 100 20 1 0.6 68.8 137 274 411 2 800 3 600 SAC45100B 16 61.5 74.2 74 85.5 5.95 8.09 11.9 540 730 1 080 1 450 2 150 2 900 0.79
50 100 20 1 0.6 70.3 144 288 432 2 700 3 400 SAC50100B 17 65.8 78.2 78 89.5 6.00 8.15 12.0 540 730 1 080 1 500 2 230 3 000 0.65
55 120 20 1 0.6 73.9 166 332 498 2 300 3 000 SAC55120B 20 79.5 92.2 92 103.6 7.08 9.62 14.2 640 860 1 280 1 740 2 590 3 480 1.15
60 120 20 1 0.6 73.9 166 332 498 2 300 3 000 SAC60120B 20 78.3 92.2 92 103.6 7.08 9.62 14.2 640 860 1 280 1 740 2 590 3 480 1.15
[Notes] 1) The basic dynamic load ratings of a single-row bearing are shown in this column. Those of matched pair and
Dynamic equivalent load Pa = XFr + YFa
stack bearings are as shown below.
Number of rows which Basic dynamic Two bearings Three bearings Four bearings
support axial loading load rating Matching types (the arrow denotes the load direction.)
Matching Types
DB DBD DBT DBB DBT
DT DTD
DF DFD DFT DFF DFT
One Ca
DB DF DBD DFD Number of rows which
support axial loading One Two One Two Three One Two Three
Two Ca × 1.625 Fa X 1.9 ⎯ 1.43 2.33 ⎯ 1.17 2.33 2.53

<
DT DBD DFD DFF = 2.17
Fr Y 0.54 ⎯ 0.77 0.35 ⎯ 0.89 0.35 0.26
Fa X 0.92
Three Ca × 2.16 > 2.17
DTD DBT DFT Fr Y 1
2) Matched bearing numbers consist of a single-row bearing number and a matching code such as DB or DF
which is shown as a suffix.
C 67 C 68
Precision ball screw support bearing units
d 17 ∼ 40 mm
L θ
x2 x3 θ1
x Z1−M1
x1
P
uD u d1 u d3 u d ud1 u d2 u D1 P
1
Z2−M2
L3 L2 L 1
Dimensions Applicable Drilled-hole of Tapped-hole for Standard Starting (Refer.)

(mm) shaft dia. Bearing housing dust-cover preload torque Mass
Unit No. 1)
d3 qty. P θ Z1-M1 P1 θ1 Z2-M2 (kg)
d D D1 L L1 L2 L3 d1 d2 x x1 x2 x3
(mm) (mm) (°) Hole No.-thread (mm) (°) Hole No.-thread (kN) (mN⋅m)
17 60 90 65 15 15 35 38 47 6 6 15 20 28 BSU1747BDF 2 75 45 4-M6 75 22.5 4-M6 2.15 140 1.72
20 60 90 65 15 15 35 38 47 6 6 15 20 28 BSU2047BDF 2 75 45 4-M6 75 22.5 4-M6 2.15 140 1.70
25 74 108 68 13 17 38 52 63 6 6 20 18 32 BSU2562BDF 2 90 30 6-M8 78 15 3-M6 3.04 200 2.45

25 74 108 83 13 17 53 52 63 6 6 20 18 32 BSU2562BDFD 3 90 30 6-M8 78 15 3-M6 4.13 260 2.85
30 74 108 68 13 17 38 52 63 6 6 20 18 40 BSU3062BDF 2 90 30 6-M8 78 15 3-M6 3.04 200 2.38

30 74 108 83 13 17 53 52 63 6 6 20 18 40 BSU3062BDFD 3 90 30 6-M8 78 15 3-M6 4.13 260 2.74
35 84 118 68 13 17 38 60 73 6 6 20 18 45 BSU3572BDF 2 100 30 6-M8 88 15 3-M6 3.73 240 2.81

35 84 118 83 13 17 53 60 73 6 6 20 18 45 BSU3572BDFD 3 100 30 6-M8 88 15 3-M6 5.07 320 3.28
35 84 118 98 13 17 68 60 73 6 6 20 18 45 BSU3572BDFF 4 100 30 6-M8 88 15 3-M6 7.46 480 3.74
40 84 118 68 13 17 38 60 73 6 6 20 18 50 BSU4072BDF 2 100 30 6-M8 88 15 3-M6 3.73 240 2.77

40 84 118 83 13 17 53 60 73 6 6 20 18 50 BSU4072BDFD 3 100 30 6-M8 88 15 3-M6 5.07 320 3.20
40 84 118 98 13 17 68 60 73 6 6 20 18 50 BSU4072BDFF 4 100 30 6-M8 88 15 3-M6 7.46 480 3.64
[Note] 1) Diagrams show a unit mounted with triple-row matched bearing DFD.
Specifications of each bearing are shown in the former pages. (BSU1747BDF → SAC1747BDF) [Refer.] Relationship between axial load and axial displacement
Bearing No.
25
SAC1747BDF, SAC2047BDF

20
15
10 SAC45100BDF, SAC50100BDF, SAC55120BDF
SAC60120BDF
0
0 5 10 15
Axial load (kN)
C 69 C 70
Full complement type cylindrical Shielded type
roller bearings for crane sheaves

Crane rope sheaves and running wheels which are
operated at low or medium speed are generally equipped with Open type
full complement type cylindrical roller bearings because the
operation of these machines involves heavy, impact loading.
These bearings are divided into shielded and open types.
The shielded type is often used with the outer ring rotation.
■ Shielded type
¡The shielded type was developed for use with rope
sheaves. It is shielded, non-separable and pre-lubricated with grease.
¡Bearings with locating snap rings around the outer ring can be positioned and fit to sheaves with
ease.
¡The bearing surface is coated with phosphate for rust prevention.
■ Open type
¡Open type bearings are further divided into those used on the fixed side and those used on the free
side. The former carry axial load in both directions. The relative position of the latter's inner ring
and outer ring can be adjusted by moving them along the axis.
¡Open type bearings are separable because the outer ring divided into two annular pieces in a
plane perpendicular to its axis. Triple-row and four-row bearings are available along with
double-row types.
Tolerances As specified in JIS B 1514-1, classes 0 and 6 (ref. Table 7-3 on pp. A 54-A 57).
Recommended fits ¡Recommended fits: refer to Table 9-4 on pp. A 85, 86.
■ Fits and clearance of full complement type cylindrical roller bearings
and radial internal for use with crane sheaves with the rotating outer ring load
clearance
Shaft Housing bore Bearing radial
Condition tolerance tolerance internal clearance
class class
Light or fluctuating load M7 CN clearance
Rotating
Normal or heavy load
outer g 6 or h 6 N7 C3 clearance
Heavy load on thin
ring load P7
section housing C3 clearance
¡Radial internal clearance : Refer to Table 10-8 (1) on p. A 100.

As for the nominal bore dia. up to 140mm shielded type
(DC5000 series), the corresponding CN clearance are
shown below.
■ CN clearance of shielded type roller bearings for nominal diameter up to
140mm
Nominal bore dia. d(mm) CN clearance (μm)
over up to min. max.
30 40 35 70
40 50 40 75
50 65 45 90
65 80 55 105
80 100 65 115
100 120 80 120
120 140 90 130
C 71 C 72
Full complement type cylindrical roller bearings
for crane sheaves
shielded type C2
d 40 ∼ 150 mm C C C
r r r
30° 30° 30°
t t t
B B B
S C1 f
uD ud uD ud uD ud u Dx u da
uE
Design 1 Design 2 Design 3 With locating snap rings
Boundary dimensions Basic load ratings Bearing No. Locating snap ring specifications Mounting dimensions (Refer.)
(mm) (kN) (mm) (mm) Mass
Design
r Without locating With locating da Dx (kg)
d D B C t Cr C0r C1 1) S E f C2 2)
min. snap rings snap rings min. min.
40 68 38 37 0.9 0.6 87.8 125 DC5008N DC5008NR 1 28 4.5 71.8 2 46 80 28 0.55
45 75 40 39 0.9 0.6 95.1 144 DC5009N DC5009NR 1 30 4.5 78.8 2 51 87 30 0.70
50 80 40 39 0.9 0.6 99.7 158 DC5010N DC5010NR 1 30 4.5 83.8 2 56 92 30 0.75
55 90 46 45 1.2 0.6 118 193 DC5011N DC5011NR 1 34 5.5 94.8 2.5 63 104 34 1.19
60 95 46 45 1.2 0.6 123 208 DC5012N DC5012NR 1 34 5.5 99.8 2.5 68 109 34 1.27
65 100 46 45 1.2 0.6 128 224 DC5013N DC5013NR 1 34 5.5 104.8 2.5 73 114 34 1.30
70 110 54 53 1.2 0.6 170 285 DC5014N DC5014NR 1 42 5.5 114.5 2.5 78 124 42 1.94
75 115 54 53 1.2 0.6 178 307 DC5015N DC5015NR 1 42 5.5 119.5 2.5 83 129 42 2.11
80 125 60 59 1.2 0.6 250 429 DC5016N DC5016NR 1 48 5.5 129.5 2.5 88 146 48 2.65
85 130 60 59 1.2 0.6 255 446 DC5017N DC5017NR 1 48 5.5 134.5 2.5 93 155 48 2.80
90 140 67 66 1.4 0.6 303 541 DC5018N DC5018NR 1 54 6 145.4 2.5 100 165 54 3.70
95 145 67 66 1.4 0.6 310 562 DC5019N DC5019NR 1 54 6 150.4 2.5 105 175 54 3.90
100 150 67 66 1.4 0.6 316 584 DC5020N DC5020NR 1 54 6 155.4 2.5 110 180 54 4.05
110 170 80 79 1.7 1 382 697 DC5022N DC5022NR 1 65 7 175.4 2.5 122 200 65 6.50
120 180 80 79 1.7 1 398 750 DC5024N DC5024NR 1 65 7 188.4 3 132 210 65 6.95
130 200 95 94 1.7 1 534 1 000 DC5026N DC5026NR 1 77 8.5 208.4 3 142 230 77 10.5
140 210 95 94 1.7 1 540 1 070 DC5028N DC5028NR 1 77 8.5 218.4 3 152 245 77 11.0
150 225 100 99 2 1 682 1 400 DC5030N DC5030NR 2 81 9 233 3 178.5 244 81 13.9
[Notes] 1) Dimensional tolerance of C 1 is +0.4/0 when bore diameter is not more than 170mm, while +0.6/0 when bore
diameter is not more than 170mm.
2) Dimensional tolerance of C 2 is − 0.1/ − 0.5 when bore diameter is not more than 170mm, while − 0.1/ − 0.7 when
bore diameter is not more than 170mm.
C 73 C 74
for crane sheaves
shielded type C2
d 160 ∼ 440 mm C C C
r r r
30° 30° 30°
t t t
B B B
S C1 f
uD ud uD ud uD ud u Dx u da
uE
Design 1 Design 2 Design 3 With locating snap rings
Boundary dimensions Basic load ratings Bearing No. Locating snap ring specifications Mounting dimensions (Refer.)
(mm) (kN) (mm) (mm) Mass
Design
r Without locating With locating da Dx (kg)
d D B C t Cr C0r C1 1) S E f C2 2)
min. snap rings snap rings min. min.
160 240 109 108 2 1.1 786 1 640 DC5032N DC5032NR 2 89 9.5 248 3 190 259 89 17.2
170 260 122 121 2 1.1 977 2 020 DC5034N DC5034NR 2 99 11 270 4 204 286 99 23.1
180 280 136 135 2 1.1 1 150 2 440 DC5036N DC5036NR 2 110 12.5 290 4 217.5 306 110 30.8
190 290 136 135 2 1.1 1 180 2 530 DC5038N DC5038NR 2 110 12.5 300 4 225 316 110 32.4
200 310 150 149 2 1.1 1 390 2 980 DC5040N DC5040NR 2 120 14.5 320 4 240 336 120 41.7
220 340 160 159 2.5 1.1 1 620 3 590 DC5044N DC5044NR 2 130 14.5 356 6 266.5 380 130 53.5
240 360 160 159 2.5 1.1 1 690 3 850 DC5048N DC5048NR 2 130 14.5 376 6 284.5 400 130 57.3
260 400 190 189 3 1.5 2 230 4 980 DC5052N DC5052NR 2 154 17.5 416 7 312.5 444 154 87.2
280 420 190 189 3 1.5 2 330 5 350 DC5056N DC5056NR 2 154 17.5 436 7 334.5 464 154 93.0
300 460 218 216 3 1.5 2 860 6 610 DC5060 ⎯ 3 ⎯ ⎯ ⎯ ⎯ 361 ⎯ ⎯ 134
320 480 218 216 3 1.5 2 950 6 930 DC5064 ⎯ 3 ⎯ ⎯ ⎯ ⎯ 378.5 ⎯ ⎯ 140
340 520 243 241 3.5 2 3 590 8 420 DC5068 ⎯ 3 ⎯ ⎯ ⎯ ⎯ 413 ⎯ ⎯ 189
360 540 243 241 3.5 2 3 660 8 720 DC5072 ⎯ 3 ⎯ ⎯ ⎯ ⎯ 427 ⎯ ⎯ 197
380 560 243 241 3.5 2 3 730 9 020 DC5076 ⎯ 3 ⎯ ⎯ ⎯ ⎯ 441 ⎯ ⎯ 207
400 600 272 270 3.5 2 4 510 11 000 DC5080 ⎯ 3 ⎯ ⎯ ⎯ ⎯ 475.5 ⎯ ⎯ 281
420 620 272 270 3.5 2 4 650 11 400 DC5084 ⎯ 3 ⎯ ⎯ ⎯ ⎯ 496 ⎯ ⎯ 290
440 650 280 278 4.5 3 4 940 12 200 DC5088 ⎯ 3 ⎯ ⎯ ⎯ ⎯ 521 ⎯ ⎯ 330
[Notes] 1) Dimensional tolerance of C 1 is +0.4/0 when bore diameter is not more than 170mm, while +0.6/0 when bore
diameter is not more than 170mm.
2) Dimensional tolerance of C 2 is − 0.1/ − 0.5 when bore diameter is not more than 170mm, while − 0.1/ − 0.7 when
bore diameter is not more than 170mm.
C 75 C 76
for crane sheaves
open type B
d 50 ∼ 200 mm P
n−u d0
S
ra
r
r ra
uD ud u Da u da
Fixed side Free side
Boundary dimensions Basic load ratings Bearing No. Lubrication hole Mounting dimensions
Mass
(mm) S 1) (kN) (mm) (mm)
Fixed side
r n da Da ra
d D B Cr C0r P d0 (kg)
min. (mm) Fixed side Free side qty min. max. max.
50 72 22 0.6 1 49.1 82.9 DC4910AVW DC4910VW 11 4 2 55 67 0.6 0.30
60 85 25 1 1 72.7 136 DC4912AVW DC4912VW 12.5 4 2 66 79 1 0.46
70 100 30 1 1 105 193 DC4914AVW DC4914VW 15 4 2 76 94 1 0.78
80 110 30 1 1 114 218 DC4916AVW DC4916VW 15 4 2 86 104 1 0.88
90 125 35 1.1 1.5 150 301 DC4918AVW DC4918VW 17.5 4 2.5 97 118 1 1.35
100 140 40 1.1 2 194 400 DC4920AVW DC4920VW 20 4 2.5 107 133 1 1.95
110 150 40 1.1 2 202 431 DC4922AVW DC4922VW 20 4 2.5 117 143 1 2.15
120 165 45 1.1 3 226 479 DC4924AVW DC4924VW 22.5 4 3 127 158 1 2.95
130 180 50 1.5 4 276 560 DC4926AVW DC4926VW 25 4 3 138.5 171.5 1.5 3.95
140 190 50 1.5 4 284 589 DC4928AVW DC4928VW 25 4 3 148.5 181.5 1.5 4.20
150 190 40 1.1 2 234 575 DC4830AVW DC4830VW 20 4 3 157 183 1 2.90
210 60 2 4 406 842 DC4930AVW DC4930VW 30 6 4 160 200 2 6.65
160 200 40 1.1 2 242 616 DC4832AVW DC4832VW 20 4 3 167 193 1 3.05
220 60 2 4 428 895 DC4932AVW DC4932VW 30 6 4 170 210 2 7.00
170 215 45 1.1 3 269 655 DC4834AVW DC4834VW 22.5 4 3 177 208 1 4.10
230 60 2 4 440 944 DC4934AVW DC4934VW 30 6 4 180 220 2 7.35
180 225 45 1.1 3 276 690 DC4836AVW DC4836VW 22.5 4 4 187 218 1 4.30
250 69 2 4 547 1 140 DC4936AVW DC4936VW 34.5 6 4 190 240 2 10.7
190 240 50 1.5 4 327 782 DC4838AVW DC4838VW 25 4 4 198.5 231.5 1.5 5.65
260 69 2 4 555 1 200 DC4938AVW DC4938VW 34.5 6 5 200 250 2 11.2
200 250 50 1.5 4 337 826 DC4840AVW DC4840VW 25 4 4 208.5 241.5 1.5 5.90
280 80 2.1 5 667 1 500 DC4940AVW DC4940VW 40 6 6 212 268 2 15.7
[Note] 1) Effective movement of the bearing on the free side in an axial direction.
C 77 C 78
for crane sheaves
open type B
d 220 ∼ 440 mm P
n−u d0
S
ra
r
r ra
uD ud u Da u da
Fixed side Free side
Boundary dimensions Basic load ratings Bearing No. Lubrication hole Mounting dimensions
Mass
(mm) S 1) (kN) (mm) (mm)
Fixed side
r n da Da ra
d D B Cr C0r P d0 (kg)
min. (mm) Fixed side Free side qty min. max. max.
220 270 50 1.5 4 355 971 DC4844AVW DC4844VW 25 6 4 228.5 261.5 1.5 6.40
300 80 2.1 5 707 1 600 DC4944AVW DC4944VW 40 6 6 232 288 2 17.1
240 300 60 2 4 509 1 330 DC4848AVW DC4848VW 30 6 5 250 290 2 10.2

320 80 2.1 5 735 1 720 DC4948AVW DC4948VW 40 6 6 252 308 2 18.4
260 320 60 2 4 532 1 450 DC4852AVW DC4852VW 30 6 5 270 310 2 11.0

360 100 2.1 6 1 070 2 520 DC4952AVW DC4952VW 50 8 6 272 348 2 32.0
280 350 69 2 4 663 1 720 DC4856AVW DC4856VW 34.5 6 5 290 340 2 16.0
380 100 2.1 6 1 130 2 700 DC4956AVW DC4956VW 50 8 6 292 368 2 33.9
300 380 80 2.1 6 802 2 160 DC4860AVW DC4860VW 40 8 6 312 368 2 23.0
420 118 3 6 1 560 3 710 DC4960AVW DC4960VW 59 8 8 314 406 2.5 53.0
320 400 80 2.1 6 832 2 310 DC4864AVW DC4864VW 40 8 6 332 388 2 24.3
440 118 3 6 1 620 3 940 DC4964AVW DC4964VW 59 8 8 334 426 2.5 56.0
340 420 80 2.1 6 853 2 430 DC4868AVW DC4868VW 40 8 6 352 408 2 25.6
460 118 3 6 1 660 4 150 DC4968AVW DC4968VW 59 8 8 354 446 2.5 59.0
360 440 80 2.1 6 880 2 580 DC4872AVW DC4872VW 40 8 6 372 428 2 27.0
480 118 3 6 1 700 4 390 DC4972AVW DC4972VW 59 8 8 374 466 2.5 62.0
380 480 100 2.1 6 1 310 3 570 DC4876AVW DC4876VW 50 8 6 392 468 2 45.3
520 140 4 7 2 290 5 600 DC4976AVW DC4976VW 70 8 8 398 502 3 92.3
400 540 140 4 7 2 380 5 990 DC4980AVW DC4980VW 70 8 8 418 522 3 96.4
420 560 140 4 7 2 440 6 270 DC4984AVW DC4984VW 70 8 8 438 542 3 101
440 600 160 4 7 2 970 7 390 DC4988AVW DC4988VW 80 8 8 458 582 3 139
[Note] 1) Effective movement of the bearing on the free side in an axial direction.
C 79 C 80
Rolling mill roll neck bearings Four-row cylindrical roller
bearings
Rolling mill roll neck four-row cylindrical roller bearings and

tapered roller bearings are designed to achieve the maximum Cylindrical bore
load rating capacity in a limited space. Bore diameter 100 – 500 mm
■ Four-row cylindrical roller bearings Four-row tapered roller

¡Suitable for high-speed rotation. Thin section designs are bearings
also available.
¡The inner ring raceway surface and the roll can be fin-
ished simultaneously after the inner ring is mounted on
the roll neck. This feature is useful in improving rolling Open type
mill accuracy.
■ Four-row tapered roller bearings
¡Suitable for low- and medium-speed rotation.
Available in both metric and inch series.
¡The internal clearance is preadjusted, facilitating Sealed type
mounting.
¡More sealed type four-row tapered roller bearings are
being used currently.
Four-row cylindrical roller bearings Four-row tapered roller bearings

Tolerances As specified in JIS B 1514-1. ¡Metric series : as specified in BAS 1002.
(refer to Table 7-3 on pp. A 54-A 57.) (refer to Table 7-6 on p. A 63.)
¡Inch series : as specified in ABMA
Section 19.
(refer to Table 7-7 on pp. A 64, 65.)
¡Special series (47T⋅⋅⋅, 4TR⋅⋅⋅) :
Special allowances are applied to these
series. For details, consult with JTEKT.
Recommended fits Refer to Table 1. ¡Metric series : refer to Table 2.

¡Inch series : refer to Table 3.
Internal clearance Refer to Table 10-8 on pp. A 100, 101. Refer to Table 10-10 on p. A 104.
(JTEKT should be consulted to determine the clearance according to application conditions.)
Equivalent load Dynamic equivalent radial load : Pr = Fr
Dynamic equivalent radial load :
Static equivalent radial load : P0r = Fr
when Fa ≤ e Pr = F r + Y 2 Fa
Fr
Fa
Pr = 0.67Fr + Y3 Fa
Fr > e
when
Static equivalent radial load :

P0r = Fr + Y0 Fa
[Note] For axial load factor Y2, Y3 and Y0, and the constant e, use values listed in the specification table.
C 81 C 82
Table 1 Roll neck four-row cylindrical roller bearing recommended fits Unit : μm Table 3 Roll neck inch series four-row tapered roller bearing recommended fits Unit : μm
Inner ring and roll neck (shaft) Outer ring and chock (housing) Double inner ring and roll neck (shaft) Outer ring and chock (housing)
Nominal bore Single plane Roll neck Nominal outside Single plane Chock bore Nominal bore Single plane Roll neck Nominal outside Single plane Chock bore
diameter mean bore diameter diameter mean outside diameter diameter mean bore diameter diameter mean outside diameter
diameter deviation diameter deviation diameter deviation diameter deviation
d deviation D deviation d deviation D deviation
(mm) 3 dmp (mm) 3 Dmp (mm)(1/25.4) 3 dmp (mm)(1/25.4) 3 Dmp
over up to upper lower upper lower over up to upper lower upper lower over up to upper lower upper lower over up to upper lower upper lower
80 120 0 − 20 + 59 + 37 120 150 0 − 18 + 40 0 76.2 101.6 + 25 0 − 75 − 100 − 304.8 + 25 0 + 75 + 50
120 180 0 − 25 + 68 + 43 (p6) 150 180 0 − 25 + 40 0 (H7) (3.0) (4.0) (12.0)
180 250 0 − 30 + 79 + 50 180 250 0 − 30 + 46 0 101.6 127.0 + 25 0 − 100 − 125 304.8 609.6 + 51 0 + 150 + 100
250 280 0 − 35 + 126 + 94 250 315 0 − 35 + 52 0 (H7) (4.0) (5.0) (12.0) (24.0)
280 315 0 − 35 + 130 + 98 (r6) 315 400 0 − 40 + 75 + 18 127.0 152.4 + 25 0 − 125 − 150 609.6 914.4 + 76 0 + 225 + 150
(G7)
315 355 0 − 40 + 144 + 108 400 500 0 − 45 + 83 + 20 (5.0) (6.0) (24.0) (36.0)
355 400 0 − 40 + 150 + 114 152.4 203.2 + 25 0 − 150 − 175 914.4 1 219.2 + 102 0 + 300 + 200
400 450 0 − 45 + 166 + 126 (r6) 500 630 0 − 50 + 92 + 22 (G7) (6.0) (8.0) (36.0) (48.0)
450 500 0 − 45 + 172 + 132 203.2 304.8 + 25 0 − 175 − 200 1 219.2 1 524.0 + 127 0 + 375 + 250
(8.0) (12.0) (48.0) (60.0)
500 560 0 − 50 + 194 + 150 (r6)
560 630 0 − 50 + 354 + 310 630 800 0 − 75 + 160 + 80 (F7) 304.8 609.6 + 51 0 − 200 − 250 1 524.0 − + 127 0 + 450 + 300
(s6) (12.0) (24.0) (60.0)
630 710 0 − 75 + 390 + 340
609.6 914.4 + 76 0 − 250 − 325
710 800 0 − 75 + 430 + 380
(24.0) (36.0)
800 900 0 − 100 + 486 + 430 (s6) 800 1 000 0 − 100 + 176 + 86 (F7)
900 1 000 0 − 100 + 526 + 470 914.4 1 219.2 + 102 0 − 300 − 400
(36.0) (48.0)
1 000 1 120 0 − 125 + 588 + 520
(s6) 1 000 1 250 0 − 125 + 203 + 98 (F7) 1 219.2 − + 127 0 − 375 − 475
1 120 1 250 0 − 125 + 646 + 580
(48.0)
1 250 1 400 0 − 160 + 235 + 110 (F7)
1 400 1 600 0 − 160 + 345 + 220 (E7)

[Note] The table above shows general values. JTEKT determines recommended fit on a case by case basis
according to bearing materials and operating conditions to prevent the inner ring from creeping.
Consult with JTEKT when referring to this table.
Table 2 Roll neck metric series four-row tapered roller bearing recommended fits Unit : μm
Double inner ring and roll neck (shaft) Outer ring and chock (housing)
Nominal bore Single plane Roll neck Nominal outside Single plane Chock bore
diameter mean bore diameter diameter mean outside diameter
diameter deviation diameter deviation
d deviation D deviation
(mm) 3 dmp (mm) 3 Dmp
over up to upper lower upper lower over up to upper lower upper lower
80 120 0 − 20 − 120 − 150 120 150 0 − 20 + 57 + 25
120 180 0 − 25 − 150 − 175 150 180 0 − 25 + 100 + 50
180 250 0 − 30 − 175 − 200 180 250 0 − 30 + 120 + 50
250 315 0 − 35 − 210 − 250 250 315 0 − 35 + 115 + 50
315 400 0 − 40 − 240 − 300 315 400 0 − 40 + 110 + 50
400 500 0 − 45 − 245 − 300 400 500 0 − 45 + 105 + 50
500 630 0 − 50 − 250 − 300 500 630 0 − 50 + 100 + 50
630 800 0 − 75 − 325 − 400 630 800 0 − 75 + 150 + 75
800 1 000 0 − 100 − 350 − 425 800 1 000 0 − 100 + 150 + 75
1 000 1 250 0 − 125 − 425 − 500 1 000 1 250 0 − 125 + 175 + 100
1 250 1 600 0 − 160 − 510 − 600 1 250 1 600 0 − 160 + 215 + 125
1 600 2 000 0 − 200 + 250 + 150
C 83 C 84
Four-row cylindrical roller bearings
d 100 ∼ (160) mm
C
r
r1
B
uD u d u Fw
Design 1-1 Design 1-2 Design 1-3 Design 1-4 Design 1-6P Design 2-1P Design 2-2 Design 2-2P Design 2-3 Design 2-4
Boundary dimensions Basic load ratings Mounting dimensions (Refer.)

(mm) (kN) (mm) Mass
Bearing No. Design1)
r 3) r1 3) da Da ra 2) rb 2) (kg)
d D B C Fw Cr C0r
min. min. min. max. min. max. max.
100 140 120 120 110 1.1 1.1 485 945 20FC14120 2-2 107 133 131 1 1 5.6
110 170 90 90 127 2 2 428 692 22FC1790 1-2 120 160 155 2 2 7.4
Design 2-5P Design 2-6P
110 180 120 120 128 2 2 636 971 22FC18120 2-2 119 170 164 2 1.5 12
115 165 90 90 132.5 1.1 1.1 398 751 23FC1690 1-1 122 158 154 1 1 6.5
120 165 87 87 134.5 1.1 1.1 374 745 24FC1787 1-2 127 158 154 1 1 5.6
120 180 105 105 135 2 1.1 487 796 4CR120 1-2 127 170 165 2 1 9.3
127 174.65 150.812 150.812 139.5 1.1 1.1 630 1 300 25FC17150 2-2 134 167 163 1 1 10.5
127 203.2 127 127 147 2 2 740 1 180 25FC20127 1-3 137 193 185 2 2 15.4
130 200 104 104 150 2 2 566 953 26FC20104 1-2 140 190 182 2 2 11.8 Design 3-1 Design 3-1P
130 200 125 125 149 2 2 752 1 310 26FC20125 1-2 140 190 183 2 2 14.4
140 190 119 119 154 1.5 1.5 565 1 160 28FC19119W 1-3 149 181 178 1.5 1.5 9.6
140 210 116 116 158 2 2 675 1 120 28FC21116 1-2 150 200 194 2 2 13.5
145 210 155 155 166 1.1 1.1 845 1 710 29FC21155 1-2 152 203 196 1 1 17.8
145 225 156 156 169 2 2 912 1 680 313924 1-2 155 215 205 2 2 22.9
150 200 120 120 162 2 2 672 1 400 30FC20120 1-2 160 190 188 2 2 10.1
150 210 120 120 168.5 2 2 686 1 380 30FC21120 2-2 160 200 196 2 2 12.8
150 210 150 150 165 2 2 872 1 780 30FC21150 1-2 160 200 195 2 2 15.9 Design 3-2P
150 220 150 150 170 2 2 887 1 760 30FC22150 1-2 160 210 202 2 2 19.2
150 220 150 150 168 2 2 889 1 760 30FC22150A 1-2 160 210 200 2 2 19.5
150 230 156 156 174 2 2 961 1 810 313891-1 1-2 160 220 210 2 2 23.8
160 220 180 180 177 2 2 964 2 170 32FC22180 1-2 170 210 205 2 2 20.5
u Da u da
160 230 130 130 180 2.1 2.1 867 1 740 314190 1-2 172 218 212 2 2 17.7
[Notes] 1) Design numbers indicate the following meanings Outer ring with rib Outer ring with loose rib 2) r a indicates housing chamfer dimension corresponding to outer ring
with P ......................... pin type cages chamfer dimension r . r b indicates the shaft chamfer dimension corre-
One inner ring 1-1, 1-2, 1-3, 1-4 1-6P
without P ..................... machined cages sponding to inner ring chamfer dimension r 1 .
Two inner rings 2-1P, 2-2, 2-2P, 2-3, 2-4 2-5P, 2-6P 3) SP indicates the specially chamfered form.
Extended inner ring 3-1, 3-1P, 3-2P
C 85 C 86
d (160) ∼ 190 mm
C
r
r1
B
uD u d u Fw

(mm) (kN) (mm) Mass
r 3) r1 3) da Da ra 2) rb 2) (kg)
d D B C Fw Cr C0r
160 230 168 168 182 1.1 1.1 1 040 2 210 32FC23170 1-2 167 223 214 1 1 22.8
160 230 168 168 180 2 2 1 040 2 200 32FC23170A 1-2 170 220 212 2 2 23.1
160 230 168 168 179 2 2 1 110 2 210 32FC23170B 1-4 170 220 215 2 2 22.6
160 230 180 180 177 2 2 1 140 2 270 32FC23180A 1-2 170 220 213 2 2 24.1
160 240 120 120 183 2.1 2.1 663 1 140 32FC24120W 1-3 172 228 219 2 2 18.5
160 240 170 170 183 2.1 2.1 1 180 2 220 32FC24170 1-2 172 228 223 2 2 26.8
170 230 120 120 187 2 2 782 1 680 34FC23120 1-2 180 220 215 2 2 14.4
170 240 156 156 190 2 2 972 2 050 34FC24156A 1-2 180 230 222 2 2 22.4
170 240 156 156 189 2 2 1 060 2 100 34FC24156B 1-2 180 230 225 2 2 21.8
170 240 190 190 187 1.5 1.5 1 260 2 620 34FC24190 1-2 179 231 223 1.5 1.5 26.9
170 250 168 168 192 2.1 2.1 1 170 2 230 34FC25168 1-2 182 238 232 2 2 27.6
170 250 170 170 192 2.1 2.1 1 170 2 230 34FC25170 1-2 182 238 232 2 2 27.8 Design 3-1 Design 3-1P
170 260 150 150 195 2.1 2.1 1 100 2 000 34FC26150 1-2 182 248 237 2 2 28.8
178 258.75 150 150 199 1.5 1.5 1 090 2 070 36FC26150 1-2 187 250 239 1.5 1.5 25.8
180 250 156 156 200 2 2 1 020 2 130 36FC25156A 1-2 190 240 234 2 2 23.3
180 260 168 168 202 2.1 2.1 1 150 2 390 313812W 1-4 192 248 238 2 2 29.7
180 260 168 168 202 2.1 2.1 1 230 2 420 36FC26168 1-2 192 248 242 2 2 29.3
180 265 180 180 203 2 2 1 300 2 600 36FC27180 1-2 190 255 243 2 2 33.6
190 260 168 168 212 2.1 2.1 1 140 2 600 38FC26168-1 1-2 202 248 244 2 2 26.5 Design 3-2P
190 270 170 170 212 2 2 1 140 2 310 38FC27170 1-2 200 260 250 2 2 30.8
190 270 170 170 213 2 2 1 140 2 310 38FC27170A 1-2 200 260 251 2 2 31.0
190 270 200 200 212 2 2 1 460 3 080 314199 1-2 200 260 252 2 2 36.1
190 280 200 200 214 2.1 2.1 1 550 3 100 38FC28200 1-2 202 268 258 2 2 42
190 290 190 190 215 2.1 2.1 1 550 2 860 38FC29190 1-2 202 278 265 2 2 44.9 u Da u da
One inner ring 1-1, 1-2, 1-3, 1-4 1-6P
C 87 C 88
d 195 ∼ 230 mm
C
r
r1
B
uD u d u Fw

(mm) (kN) (mm) Mass
r 3) r1 3) da Da ra 2) rb 2) (kg)
d D B C Fw Cr C0r
195 300 226 226 220 2.1 2.1 1 960 3 690 39FC30226 1-2 207 288 274 2 2 57.9
200 270 170 170 222 2 2.1 1 190 2 780 314553 1-2 212 260 254 2 2 28.0
200 280 152 152 222 2.1 2.1 1 100 2 150 40FC28152BW 1-3 212 268 262 2 2 28.0
200 280 170 170 222 2.1 2.1 1 280 2 620 40FC28170 1-2 212 268 262 2 2 31.7
200 280 188 188 222 2.1 2.1 1 350 2 810 40FC28188 1-2 212 268 262 2 2 35.0
200 280 190 190 223 3 3 1 460 3 100 40FC28190A 1-2 214 266 263 2.5 2.5 36.0
200 280 200 200 222 2 2 1 450 3 090 313893-1 1-2 210 270 262 2 2 37.7
200 280 200 200 224 2.1 2.1 1 450 3 330 40FC28200 1-2 212 268 260 2 2 38.7
200 290 192 192 226 2.1 2.1 1 460 3 030 313811 1-2 212 278 268 2 2 42.0
200 310 160 160 232 2.1 2.1 1 260 2 240 40FC31160 1-1 212 298 282 2 2 44.6
200 310 206 206 227 2.1 2.1 1 790 3 240 40FC31206 1-2 212 298 283 2 2 56.6
Design 3-1 Design 3-1P
206 299.97 170 170 229 2 2 1 470 2 780 41FC30170 1-2 216 289 277 2 2 39.2
210 290 192 192 236 2.1 2.1 1 460 3 270 42FC29192 1-2 222 278 274 2 2 38.1
210 300 210 210 234 2.1 2.1 1 660 3 490 42FC30210 1-2 222 288 278 2 2 47.3
220 300 150 150 240 2.1 2.1 1 210 2 500 44FC30150W 1-3 232 288 280 2 2 30.7
220 310 192 192 247 2.1 2.1 1 520 3 270 313837-1 1-2 232 298 289 2 2 45.5
220 310 192 192 246 2 2 1 630 3 420 313837A 1-2 230 300 291 2 2 44.9
220 310 192 192 245 3 2.1 1 450 2 980 44FC31192W 1-3 232 296 289 2.5 2 43.9
220 310 225 225 244 2.1 2.1 1 880 4 160 44FC31225A 1-2 232 298 288 2 2 53.5 Design 3-2P
220 320 210 210 246 2.1 2.1 1 760 3 490 44FC32210 1-2 232 308 296 2 2 55.4
220 320 210 210 248 2.1 2.1 1 810 3 740 44FC32210-1 1-4 232 308 296 2 2 56.7
220 340 180 180 256 3 3 1 500 2 750 44FC34180A 1-4 234 326 310 2.5 2.5 59.0
230 330 206 206 260 2.1 2.1 1 880 3 980 313824A 1-2 242 318 308 2 2 57.5 u Da u da
230 340 260 260 261 3 3 2 310 4 900 46FC34260 1-2 244 326 313 2.5 2.5 81.2
One inner ring 1-1, 1-2, 1-3, 1-4 1-6P
C 89 C 90
d 237 ∼ (280) mm
C
r
r1
B
uD u d u Fw

(mm) (kN) (mm) Mass
r 3) r1 3) da Da ra 2) rb 2) (kg)
d D B C Fw Cr C0r
237 339.67 200 200 264 2 2 1 840 3 780 47FC34200 1-2 247 329 314 2 2 58.0
240 330 220 220 270 3 3 1 780 4 250 312943/1YD 1-4 254 316 310 2.5 2.5 55.5
240 330 220 220 264 2.1 2.1 1 830 4 120 48FC33220 1-2 252 318 308 2 2 54.3
240 330 220 220 268 3 3 1 770 4 070 48FC33220BW 1-4 254 316 310 2.5 2.5 55.5
240 330 250 250 263 2.1 2.1 2 160 4 910 48FC33250W 1-3 252 318 309 2 2 63.7
240 340 200 200 266 3 3 1 880 3 780 48FC34200 1-2 254 326 318 2.5 2.5 56.3
240 340 220 220 268 3 3 2 000 4 240 48FC34220 1-2 254 326 318 2.5 2.5 63.4
250 350 220 220 278 3 3 1 930 4 200 50FC35220 1-2 264 336 326 2.5 2.5 64.6
260 355 260 260 286 2.1 2.1 2 290 5 440 52FC35260 2-2 272 343 332 2 2 75.0
260 360 192 192 287 2.1 2.1 1 750 3 740 52FC36192W 1-3 272 348 335 2 2 59.8
260 360 200 200 287 2.1 2.1 1 880 4 110 52FC36200 1-2 272 348 335 2 2 62.0
260 360 230 230 292.5 2.1 2.1 2 140 4 900 52FC36230CW 1-4 272 348 340 2 2 69.7
260 360 230 230 292 2.1 2.1 2 020 4 790 52FC36230D 1-2 272 348 336 2 2 72.6
260 360 260 260 287 2.1 2.1 2 300 5 320 52FC36260 2-2 272 348 335 2 2 80.0
260 368 268 268 288 2.1 2.1 2 740 5 990 52FC37268W 1-4 272 356 344 2 2 89.9
260 370 220 220 292 3 3 2 000 4 330 313823 1-2 274 356 342 2.5 2.5 76.0
260 370 220 220 290 3 3 2 180 4 480 313823A 1-2 274 356 346 2.5 2.5 75.0
260 370 260 260 290 2.1 2.1 2 640 5 740 52FC37260 1-2 272 358 346 2 2 88.5
265 370 234 234 292 1.5 1.5 2 290 4 910 53FC37234A 1-2 274 361 346 1.5 1.5 76.3 Design 3-2P
265 370 234 234 300 1.5 1.5 2 270 5 290 53FC37234B 2-2 274 361 348 1.5 1.5 78.5
270 380 230 230 298 2.1 2.1 2 330 4 910 54FC38230 1-2 282 368 354 2 2 80.0
280 380 170 170 306 2.1 2.1 1 710 3 590 56FC38170W 1-3 292 368 356 2 2 55.0
280 390 220 220 312 3 3 2 070 4 640 313822 1-2 294 376 362 2.5 2.5 81.8 u Da u da
280 390 220 220 308 3 3 2 180 4 670 313822A 1-2 294 376 362 2.5 2.5 79.7
with P ......................... pin type cages chamfer dimension r. r b indicates the shaft chamfer dimension corre-
One inner ring 1-1, 1-2, 1-3, 1-4 1-6P
C 91 C 92
d (280) ∼ (320) mm
C
r
r1
B
uD u d u Fw

(mm) (kN) (mm) Mass
r 3) r1 3) da Da ra 2) rb 2) (kg)
d D B C Fw Cr C0r
280 390 220 220 306 3 2.1 2 520 5 350 313822C 1-2 292 376 364 2.5 2 79.7
280 390 220 220 312 3 3 2 320 5 100 313822D 1-2 294 376 366 2.5 2.5 80.1
280 390 240 240 312 3 3 2 460 5 620 56FC39240 1-2 294 376 364 2.5 2.5 88.1
280 390 275 275 309 2.1 2.1 2 680 6 110 56FC39275B 1-2 292 378 363 2 2 100
280 390 275 275 308 3 2.1 3 040 6 850 56FC39275J 2-4 292 376 366 2.5 2 102
280 410 300 300 314 3 3 3 730 8 400 56FC41300 2-6P 294 396 378 2.5 2.5 137
290 390 234 234 320 3 3 2 300 5 500 58FC39234 1-2 304 376 368 2.5 2.5 80.0
290 400 180 180 320 3 3 1 880 4 010 58FC40180W 1-2 304 386 372 2.5 2.5 68.3
290 410 240 240 320 3 3 2 610 5 540 58FC41240 1-2 304 396 380 2.5 2.5 99.0
290 420 300 300 327 3 3 3 100 6 960 58FC42300 1-2 304 406 387 2.5 2.5 138
300 400 300 300 328 3 3 2 920 7 310 60FC40300A 1-2 314 386 378 2.5 2.5 103 Design 3-1 Design 3-1P
300 420 218 218 332 3 3 2 350 5 010 60FC42218 1-1 314 406 390 2.5 2.5 93.0
300 420 240 240 332 3 3 2 660 5 750 60FC42240 1-1 314 406 392 2.5 2.5 102
300 420 300 300 332 3 3 3 370 7 840 4CR300 3-2P 314 406 392 2.5 2.5 125
300 420 300 300 331 1.5 1.5 3 420 7 750 60FC42300DW 2-4 309 411 395 1.5 1.5 127
300 420 300 300 332 2 2 3 750 8 690 60FC42300L-2 2-6P 310 410 395 2 2 129
300 420 300 300 332 3 3 3 250 7 270 60FC42300W 2-3 314 406 394 2.5 2.5 127
310 420 300 300 338 3 3 3 090 7 370 62FC42300 1-2 324 406 394 2.5 2.5 119
310 430 240 240 344.5 3 3 2 640 5 770 62FC43240 1-2 324 416 404 2.5 2.5 105
Design 3-2P
310 440 240 240 341 3 3 2 820 5 730 62FC44240 1-2 324 426 409 2.5 2.5 113
320 440 230 230 351 3 3 2 530 5 490 64FC44230/240 1-2 334 426 411 2.5 2.5 103
320 450 240 240 358 3 3 2 700 5 740 4CR320 1-2 334 436 422 2.5 2.5 119
320 450 240 240 355 3 3 2 700 5 730 64FC45240 1-2 334 436 419 2.5 2.5 117
320 450 240 240 358 3 3 2 770 5 930 64FC45240CW 1-4 334 436 422 2.5 2.5 118 u Da u da
320 460 340 340 360 3 3 3 860 8 730 64FC46340A 1-4 334 446 428 2.5 2.5 187
One inner ring 1-1, 1-2, 1-3, 1-4 1-6P
C 93 C 94
d (320) ∼ 370 mm
C
r
r1
B
uD u d u Fw

(mm) (kN) (mm) Mass
r 3) r1 3) da Da ra 2) rb 2) (kg)
d D B C Fw Cr C0r
320 480 290 290 361 4 4 4 080 8 450 64FC48290 2-6P 338 462 441 3 3 189
320 480 350 350 364 2.1 2.1 5 010 11 000 314274A 2-6P 332 468 444 2 2 227
330 440 200 200 358 3 3 2 340 5 220 66FC44200AW 1-3 344 426 414 2.5 2.5 83.4
330 440 200 200 360 3 5 2 050 4 670 66FC44200W 1-3 352 426 412 2.5 4 83.0
330 460 340 340 364 2.1 2.1 3 860 9 150 66FC46340 1-2 342 448 428 2 2 172
330 460 340 340 368 4 4 4 060 9 800 66FC46340B 1-2 348 442 432 3 3 176
330 460 380 380 364 2.1 2.1 4 380 10 800 66FC46380W 1-4 342 448 428 2 2 195
340 445 250 250 367 2.1 4 2 510 6 110 68FC45250W 1-3 358 433 419 2 3 100
340 450 250 250 368 2.1 2.1 2 750 6 480 68FC45250BW 1-3 352 438 424 2 2 106
340 480 350 350 378 4 SP 4 580 11 100 68FC48350-2 2-4 354 462 446 3 2 211
340 480 350 350 378 3 SP 4 780 11 500 68FC48350D 3-2P 354 466 448 2.5 2 201 Design 3-1 Design 3-1P
340 480 350 350 376 4 4 4 840 11 400 68FC48350L 3-2P 358 462 448 3 3 201
340 480 385 350 378 2.1 SP 4 780 11 500 68FC48350N 2-6P 358 468 448 2 3 209
340 490 300 300 380 5 5 3 500 7 690 68FC49300 1-2 362 468 450 4 4 187
340 490 300 300 379 5 5 3 680 7 850 68FC49300A 1-2 362 468 453 4 4 182
343.052 457.098 254 254 374 3 3 2 640 6 190 69FC46254W 1-4 358 443 430 2.5 2.5 112
350 500 460 460 388 2 2 6 570 16 500 70FC50460 2-6P 360 490 464 2 2 296
360 480 290 290 392 3 3 3 470 8 510 72FC48290 1-2 374 466 452 2.5 2.5 145 Design 3-2P
360 500 250 250 394 3 3 3 510 7 340 72FC50250 2-2 374 486 470 2.5 2.5 145
360 510 370 370 400 4 4 4 590 11 000 72FC51370 1-2 378 492 470 3 3 241
360 520 380 380 405 2 5 5 800 13 700 72FC52380 2-6P 382 510 485 2 4 270
370 520 380 380 409 5 5 5 320 13 200 74FC52380 2-6P 392 498 481 4 4 257
370 520 400 400 413 5 5 4 740 11 900 74FC52400W 2-4 392 498 481 4 4 268 u Da u da
370 540 400 400 415 4 4 5 190 11 500 74FC54400A 1-2 388 522 499 3 3 311
One inner ring 1-1, 1-2, 1-3, 1-4 1-6P
C 95 C 96
d 375 ∼ (420) mm
C
r
r1
B
uD u d u Fw

(mm) (kN) (mm) Mass
r 3) r1 3) da Da ra 2) rb 2) (kg)
d D B C Fw Cr C0r
375 545 400 400 417 4 4 6 310 14 500 75FC55400 3-2P 393 527 505 3 3 315
380 520 280 280 417 4 4 3 720 8 550 76FC52280 1-2 398 502 487 3 3 173
380 520 290 290 418 4 4 3 760 8 840 76FC52290 1-2 398 502 486 3 3 181
380 540 300 300 421 3 3 4 650 10 100 76FC54300 2-6P 394 526 505 2.5 2.5 222
380 540 340 340 422 4 4 4 600 10 300 76FC54340W 3-1 398 522 502 3 3 256
380 540 360 360 422 4 4 5 480 12 900 76FC54360 2-6P 398 522 502 3 3 266
380 540 400 380 422 4 4 6 010 14 300 76FC54380 2-6P 398 522 504 3 3 287
380 540 400 400 422 4 4 6 040 14 600 76FC54400BW 2-6P 398 522 502 3 3 298
380 540 400 400 422 4 4 6 040 14 600 76FC54400DW 3-2P 398 522 502 3 3 298
390 550 400 400 434 5 SP 5 130 12 400 78FC55400AW 2-3 410 528 510 4 4 296
400 520 250 250 432 4 4 2 920 7 100 80FC52250W 1-3 418 502 492 3 3 133
400 560 360 360 441 5 5 5 570 13 400 80FC56360 2-6P 422 538 521 4 4 277
400 560 410 410 445 5 5 6 330 15 800 4CR400 3-2P 422 538 525 4 4 310
400 560 410 410 445 2 5 6 470 16 300 80FC56410 2-6P 422 550 525 2 4 315
400 600 380 380 450 5 5 6 610 14 300 80FC60380 2-6P 422 578 552 4 4 388
406.4 609.6 304.8 304.8 460 5 5 4 380 8 750 81FC6130W 1-4 429 587 556 4 4 307
410 546 400 400 448 5 5 5 010 13 000 82FC55400 2-2 432 524 516 4 4 256
410 600 440 440 460 5 5 8 070 18 800 82FC60440 2-6P 432 578 560 4 4 432 Design 3-2P
418.5 600 410 410 470 5 5 6 630 15 700 84FC60410A 2-6P 441 578 560 4 4 385
419 592 350 350 462 4 4 5 690 12 900 84FC59350 1-6P 437 574 552 3 3 304
420 560 280 280 457 4 4 3 930 9 410 84FC56280 1-1 438 542 527 3 3 189
u Da u da
420 560 400 400 458 4 4 4 870 12 700 84FC56400 2-4 438 542 526 3 3 270
One inner ring 1-1, 1-2, 1-3, 1-4 1-6P
C 97 C 98
d (420) ∼ (480) mm
C
r
r1
B
uD u d u Fw

(mm) (kN) (mm) Mass
r 3) r1 3) da Da ra 2) rb 2) (kg)
d D B C Fw Cr C0r
420 580 320 320 463 4 4 4 760 11 000 84FC58320 2-4 438 562 543 3 3 249
420 600 440 440 470 5 5 7 240 17 700 4CR420A 3-1P 442 578 560 4 4 420
430 591 420 420 472 5 5 6 550 16 800 86FC59420 2-2P 452 569 552 4 4 345
430 591 420 420 476 4 4 6 520 17 400 86FC59420-2 2-6P 448 573 552 3 3 349
430 591 420 420 476 4 4 5 910 14 700 86FC59420A-1 1-3 448 573 552 3 3 340
430 600 450 450 475 5 5 7 460 19 300 86FC60450 2-6P 452 578 559 4 4 405
440 590 270 270 482 4 4 3 620 8 460 88FC59270W 1-3 458 572 554 3 3 207
440 620 450 450 487 4 4 7 900 20 000 4CR440 3-1P 458 602 577 3 3 440
440 620 450 450 487 4 4 7 900 20 000 88FC62450AW 2-6P 458 602 577 3 3 440
440 640 420 420 492 5 5 7 820 18 400 88FC64420 2-6P 462 618 592 4 4 470
440 720 452 452 512 6 6 8 570 16 600 88FC72452 1-6P 468 692 652 5 5 740 Design 3-1 Design 3-1P
444.5 660.4 323.85 323.85 500 4 4 6 040 12 600 89FC66324 1-6P 463 642 608 3 3 400
445 635 375 375 496 4 4 6 240 14 600 4CR445 3-1P 463 617 588 3 3 385
450 630 450 450 500 4 4 6 820 16 600 90FC63450A 2-2 468 612 590 3 3 433
460 600 400 400 497 4 SP 5 300 14 300 92FC60400 2-4 478 582 567 3 3 287
460 620 400 400 504 4 4 6 850 18 200 4CR460C 3-1P 478 602 584 3 3 350
460 620 400 400 502 4 4 6 510 17 000 92FC62400BW 1-6P 478 602 582 3 3 350
Design 3-2P
460 620 400 400 502 4 4 5 900 14 800 92FC62400D 1-4 478 602 583 3 3 340
460 650 470 470 509 6 6 8 990 22 200 92FC65470W 1-6P 488 622 609 5 5 494
460 660 500 500 512 4 4 9 310 23 300 4CR460 3-1P 478 642 612 3 3 590
460 660 500 500 510 5 5 9 540 23 400 92FC66500 2-6P 482 638 614 4 4 573
460 680 400 400 504 4 4 7 910 16 600 4CR460D 3-1P 478 662 624 3 3 510
u Da u da
480 650 450 450 525 5 5 8 480 22 400 96FC65450B 2-6P 502 628 615 4 4 440
One inner ring 1-1, 1-2, 1-3, 1-4 1-6P
C 99 C 100
d (480) ∼500 mm
C
r
r1
B
uD u d u Fw

(mm) (kN) (mm) Mass
r 3) r1 3) da Da ra 2) rb 2) (kg)
d D B C Fw Cr C0r
480 650 460 460 526 5 5 7 730 20 800 96FC65460 2-6P 502 628 610 4 4 443
480 680 460 460 532 5 5 8 620 21 300 96FC68460 2-6P 502 658 632 4 4 545
480 680 500 500 534 5 5 8 620 22 000 4CR480 3-1P 502 658 630 4 4 580
480 680 500 500 534 5 5 8 620 22 000 4CR480B 3-2P 502 658 630 4 4 580
480 680 500 500 532 5 5 9 550 24 300 96FC68500A 2-6P 502 658 632 4 4 595
495 615 360 360 530 SP SP 4 030 12 000 99FC62360 2-4 511 597 586 3 3 235
500 670 450 450 540 5 SP 8 460 22 500 100FC67450A-3 2-6P 522 648 630 4 4 451
500 680 420 405 550 5 5 6 710 17 600 100FC68405 2-6P 522 658 634 4 4 442
500 680 450 450 542.5 4 4 8 980 23 100 100FC68450 2-6P 518 662 639 3 3 495
500 690 510 510 550 5 5 9 350 24 600 100FC69510A 3-2P 522 668 646 4 4 562
500 710 480 480 558 6 6 9 770 24 800 100FC71480 2-6P 528 682 662 5 5 631 Design 3-1 Design 3-1P
500 720 400 400 558 5 6 8 320 18 900 100FC72400 1-6P 528 698 672 4 5 549
500 720 530 530 560 6 6 10 800 26 500 100FC72530 2-6P 528 692 674 5 5 725
500 720 530 530 568 5 4 11 000 28 900 100FC72530C 2-6P 518 698 672 4 3 742
500 720 530 530 560 6 6 10 800 26 500 100FC72530W 3-2P 528 692 674 5 5 725
One inner ring 1-1, 1-2, 1-3, 1-4 1-6P
Design 3-2P
u Da u da
C 101 C 102
Four-row tapered roller bearings
d 65 ∼ 133.350 mm
T For oil mist lubrication S
r ra
r1
W
uD ud uDa uda
Design 1 Design 1-P Design 2 Design 2-P
Boundary dimensions Basic load ratings Mounting dimensions Con- Axial load factors (Refer.)
(mm) (kN) (mm) stant Mass
Bearing No. 1) Design
r r1 da Da S ra rb 2) (kg)
d D T W Cr C0r e Y2 Y3 Y0
min. min. max. max. min. min. max. max.
65 100 98 98 1.5 0.3 309 550 47T131010 1 73 91.5 87 3.6 1.5 0.3 0.46 1.47 2.19 1.44 2.82
80 115 88 88 1.5 1.5 265 543 47T1611 1 91 106.5 102 3.4 1.5 1.5 0.33 2.03 3.02 1.98 2.99
95 130 100 100 1.5 1.5 347 729 47T191310 1 104 121.5 117 3.5 1.5 1.5 0.33 2.03 3.02 1.98 3.83
100 140 104 104 2 2.5 338 661 37220 1 112 130 125 3.8 2 2 0.28 2.37 3.53 2.32 4.6
100 140 104 104 2 1 407 852 37220A 1 110 130 125 4.1 2 1 0.40 1.68 2.50 1.64 4.8
100 170 155 155 2 2.5 787 1 470 47T2017 1 119 160 149 5.7 2 2 0.35 1.95 2.90 1.91 14.7
105 160 150 150 1.5 1 747 1 420 47T211615 1 118 151.5 146 5.9 1.5 1 0.33 2.03 3.02 1.98 10.6
110 155 114 114 2 2.5 475 955 37222 1 121 145 140 4.8 2 2 0.33 2.03 3.02 1.98 6.45
110 160 115 115 1.5 1 548 1 030 47T221612 1 121 151.5 146 5.2 1.5 1 0.43 1.57 2.34 1.53 7.63
110 180 154 154 2 2.5 882 1 530 47T221815 1 127 170 162 5.9 2 2 0.39 1.74 2.59 1.70 15.4
110 180 170 170 1 1 989 1 770 47T221817 1 126 174.5 162 6.5 1 1 0.33 2.03 3.02 1.98 17
115 155 115 115 1.5 0.6 437 1 020 47T231612A 1 126 146.5 142 3.4 1.5 0.6 0.40 1.68 2.50 1.64 6.12
115 160 120 120 1.5 0.6 560 1 160 47T231612 1 124 151.5 147 5.7 1.5 0.6 0.35 1.95 2.90 1.91 7.2
120 170 124 124 2 2.5 472 943 37224 1 135 160 155 4.1 2 2 0.28 2.37 3.53 2.32 8.56
120 170 130 130 1.5 2 591 1 290 47T241713 1 133 161.5 155 4.4 1.5 2 0.40 1.68 2.50 1.64 9.38
120 200 132 132 2 2.5 706 1 200 47324 1 143 190 178 5.7 2 2 0.35 1.95 2.90 1.91 16.5
120 210 174 174 2.5 3 1 110 1 770 47T242117 1 143 198 188 4 2 2.5 0.33 2.03 3.02 1.98 24.5
120.650 161.925 106.365 106.365 1.6 1.6 322 771 L624549D/514/514D 1 130 153 147 5.1 1.6 1.6 0.43 1.56 2.32 1.52 6.24
120.650 166.688 152.414 152.400 3.3 1.6 637 1 460 LM124449D/410/410D 1 132 155 150 2.3 3.3 1.6 0.29 2.30 3.42 2.25 9.84
120.650 174.625 139.703 141.288 1.6 0.8 712 1 450 M224749D/710/710D 1 133 166 159 4.9 1.6 0.8 0.33 2.03 3.02 1.98 11.1
127.000 182.563 158.750 158.750 3.2 1.6 778 1 720 48290D/20/20D 1 140 171 166 3.7 3.2 1.6 0.31 2.21 3.29 2.16 13.6
130 184 134 134 2 2.5 645 1 330 37226 1 143 174 169 4.3 2 2 0.33 2.03 3.02 1.98 11
133.350 196.850 193.675 193.675 3.2 1.6 1 070 2 240 67390D/22/22D 1 148 185 180 5.6 3.2 1.6 0.34 1.96 2.92 1.92 19.8
[Notes] 1) While metric series bearings have minus tolerances for bore and OD, inch series have plus tolerances. Refer 2) r b indicates the shaft chamfer dimension corresponding to cone chamfer dimension r 1 .
to page C 82 for details of applicable tolerance standards.
C 103 C 104
d 135 ∼ 170 mm
r ra
r1
W
uD ud uDa uda
135 180 160 160 1.5 1 559 1 290 47T271816 1 146 171.5 166 1.4 1.5 1 0.33 2.03 3.02 1.98 10.7
135 195 160 160 1.5 0.6 938 1 930 47T272016 1 147 186.5 179 3.9 1.5 0.6 0.33 2.03 3.02 1.98 15.4
136.525 190.500 161.925 161.925 3.2 1.6 809 1 890 47T271916 2 150 179 174 4.8 3.2 1.6 0.32 2.10 3.13 2.06 14.3
136.525 190.500 161.925 161.925 3.2 1.6 809 1 890 48393D/20/20D 1 150 179 174 4.8 3.2 1.6 0.32 2.10 3.13 2.06 14.3
139.700 200.025 160.340 157.166 3.3 0.8 844 1 960 48680D/20/20D 1 157 187 182 4 3.3 0.8 0.34 2.01 2.99 1.96 16.6
140 198 144 144 2 2.5 770 1 650 37228 1 157 188 183 5.3 2 2 0.28 2.43 3.61 2.37 13.6
140 210 114 114 2 2.5 623 1 130 47228 1 160 200 190 6 2 2 0.27 2.47 3.67 2.41 13.7
140 225 145 145 2.5 3 973 1 610 47328 1 161 213 203 6.5 2 2.5 0.40 1.68 2.50 1.64 21.2
145 195 130 130 1.5 0.6 641 1 550 47T292013 1 158 186.5 177 5.1 1.5 0.6 0.40 1.68 2.50 1.64 11.1
150 210 190 190 2 0.6 993 2 270 47T302119 1 163 200 190 5 2 0.6 0.39 1.74 2.59 1.70 20.2
150 212 155 155 2.5 3 774 1 640 37230 1 168 200 190 6 2 2.5 0.28 2.37 3.53 2.32 16.7
152.400 222.250 174.625 174.625 1.6 1.6 1 080 2 390 M231649D/610/610D 1 168 213 201 6 1.6 1.6 0.33 2.03 3.02 1.98 22.8
160 226 165 165 2.5 3 873 1 870 37232 1 178 214 204 6 2 2.5 0.28 2.37 3.53 2.32 20.1
160 250 145 145 2.5 3 1 090 1 870 47T322515 1 182 238 226 6.5 2 2.5 0.33 2.03 3.02 1.98 25.4
160 265 173 173 2.5 1 1 320 2 400 47T322717 1 193 253 241 7 2 1 0.35 1.95 2.90 1.91 37.6
165.100 225.425 168.275 165.100 3.2 0.8 868 2 140 46791D/20/21D 1 180 213 203 4.5 3.2 0.8 0.38 1.77 2.63 1.73 19.7
168.275 247.650 192.088 192.088 3.2 1.6 1 190 2 800 67782D/20/21D 1 189 236 226 5 3.2 1.6 0.44 1.54 2.29 1.50 31.7
170 230 175 175 2 1 1 030 2 370 47T342318 1 183 220 210 6 2 1 0.40 1.68 2.50 1.64 19.9
170 240 175 175 2.5 3 1 020 2 310 37234A 1 189 228 218 5 2 2.5 0.33 2.03 3.02 1.98 24.2
170 240 175 175 2.5 1.5 1 120 2 340 47T342418A 2 184 228 218 7.5 2 1.5 0.40 1.68 2.50 1.64 24.7
170 260 160 160 2.5 3 1 110 1 900 47T342616 1 194 248 238 6 2 2.5 0.35 1.95 2.90 1.91 28.5
170 280 181 181 2.5 3 1 330 2 420 47334/181 1 202 268 250 6 2 2.5 0.33 2.03 3.02 1.98 44
170 280 185 185 2.5 3 1 330 2 420 47334 1 202 268 250 6 2 2.5 0.33 2.03 3.02 1.98 44.8
C 105 C 106
d 177.800 ∼ 205 mm

r ra
r1
W
uD ud uDa uda
177.800 247.650 192.088 192.088 3.2 1.6 1 190 2 800 67791D/20/21D 1 189 235 225 5 3.2 1.6 0.44 1.54 2.29 1.50 28.4
177.800 279.400 234.948 234.950 3.2 1.6 1 660 3 290 82681D/20/20D 1 197 267 251 6.5 3.2 1.6 0.52 1.29 1.92 1.26 52.5
177.800 285.750 222.245 222.500 3.2 1.6 1 520 2 860 EE91700D/112/113XD 1 201 273 251 3.5 3.2 1.6 0.43 1.57 2.34 1.53 53.7
180 250 185 185 2.5 3 1 140 2 550 47T362519 1 198 238 228 6 2 2.5 0.33 2.03 3.02 1.98 26.9
180 254 185 185 2.5 3 1 140 2 550 37236 1 198 242 232 6 2 2.5 0.33 2.03 3.02 1.98 29.1
180 260 160 160 2.5 1 1 090 2 090 47T362616 1 198 248 238 5 2 1 0.37 1.80 2.69 1.76 26.4
180 260 200 200 2 2.5 1 390 2 950 47T362620 1 200 250 240 4.5 2 2 0.31 2.15 3.20 2.10 33.6
180 280 181 181 2.5 3 1 510 2 830 47T362818A 1 204 268 253 8 2 2.5 0.33 2.03 3.02 1.98 40.8
180 300 202 202 3 4 1 580 2 750 47336 1 211 286 267 5.5 2.5 3 0.35 1.95 2.90 1.91 54.9
180 300 280 280 3 4 2 400 4 430 47T363028 1 211 286 270 6 2.5 3 0.33 2.03 3.02 1.98 78.4
187 270 210 210 2.5 1 1 660 3 570 47T372721B 1 205 258 248 8 2 1 0.33 2.03 3.02 1.98 39.1
187.325 269.875 211.138 211.138 3.2 1.6 1 410 3 220 M238849D/810/810D 1 206 257 245 5 3.2 1.6 0.33 2.03 3.02 1.98 39.5
190 268 196 196 2.5 3 1 210 2 760 37238 1 210 256 246 6 2 2.5 0.33 2.03 3.02 1.98 33.4
190 270 160 160 2.5 1 1 170 2 370 47T382716 1 208 258 248 7 2 1 0.40 1.68 2.50 1.64 28.3
190.000 270.000 190.000 190.000 3.2 1.6 1 160 2 810 4TR3827 1 208 257 244 6 3.2 1.6 0.48 1.42 2.11 1.38 34.7
190.500 266.700 188.913 187.325 3.2 1.6 1 160 2 810 67885D/67820/67820D 1 208.5 255.3 245.1 6 3.2 1.6 0.48 1.42 2.11 1.38 32.4
198.438 284.163 225.425 225.425 3.2 1.6 1 740 3 780 M240648D/611/611D 1 215 271 260 5 3.2 1.6 0.33 2.03 3.02 1.98 44.7
200 280 206 206 2.5 1.5 1 670 3 830 47T402821 1 216 268 258 6.5 2 1.5 0.39 1.71 2.54 1.67 39.7
200 282 206 206 2.5 3 1 490 3 380 37240 1 223 270 260 5.5 2 2.5 0.28 2.43 3.61 2.37 39.6
200 340 234 234 3 4 2 340 4 150 47T403423 1 234 326 302 6 2.5 4 0.40 1.68 2.50 1.64 86
203.200 317.500 209.550 215.900 3.2 3.2 1 510 2 900 EE132082D/125/126D 1 235 304 284 7 3.2 3.2 0.31 2.15 3.21 2.11 61
203.200 317.500 266.700 266.700 3.2 1.6 2 070 4 540 93800D/125/127D 1 223 304 278 6.5 3.2 1.6 0.52 1.29 1.92 1.26 78.8
205 320 205 205 3 4 1 740 3 030 47T413221 1 230 306 292 7.5 2.5 3 0.46 1.46 2.17 1.42 58.9
C 107 C 108
d 206.375 ∼ 235 mm

r ra
r1
W
uD ud uDa uda
206.375 282.575 184.150 184.150 3.2 0.8 1 200 2 830 67985D/20/20D 1 219 270 259 7 3.2 0.8 0.51 1.33 1.97 1.30 33.9
206.375 282.575 190.500 190.500 3.2 0.8 1 200 2 830 67986D/20/21D 1 222 270 259 7 3.2 0.8 0.51 1.33 1.97 1.30 34.8
206.375 282.575 210.000 210.000 3.2 0.8 1 380 3 010 47T412821A 1 219 270 260 3.5 3.2 0.8 0.43 1.57 2.34 1.53 36.2
215.090 311.150 228.600 228.600 3.2 1.6 1 750 4 040 47T433123 1 233 297 278 7 3.2 1.6 0.40 1.68 2.50 1.64 57.5
215.900 288.925 177.800 177.800 3.2 0.8 1 220 3 120 LM742749D/714/714D 1 229 276 265 5.5 3.2 0.8 0.48 1.40 2.09 1.37 32.8
215.900 336.550 266.700 266.700 3.2 6.4 2 430 4 760 47T433427 1 238 323 304 6.5 3.2 6.4 0.50 1.34 2.00 1.32 85.1
216.103 330.200 269.875 263.525 3.2 1.6 2 500 5 120 47T433327 1 237 316 300 7 3.2 1.6 0.46 1.47 2.19 1.44 81.6
220 300 230 230 2.5 3 1 750 4 040 47T443023 1 231 288 278 6.5 2 2.5 0.40 1.68 2.50 1.64 45.1
220 310 226 226 3 4 1 690 3 880 37244 1 242 296 285 6 2.5 3 0.33 2.03 3.02 1.98 52
220 320 201 201 3 3 1 660 3 760 47T443220 1 247 306 290 5.5 2.5 2.5 0.33 2.03 3.02 1.98 52.4
220 320 250 250 2.5 3 1 930 4 230 47T443225 1 244 308 293 6.5 2 2.5 0.35 1.95 2.90 1.91 64.7
220 330 260 260 3 1 2 350 5 070 47T443326A 1 243 316 299 9 2.5 1 0.40 1.68 2.50 1.64 78.4
220 330 260 260 3 1 2 330 4 860 47T443326B 2 238 316 300 8 2.5 1 0.55 1.24 1.84 1.21 77.5
220 340 190 190 3 4 1 490 2 910 47244 1 260 326 308 6 2.5 3 0.28 2.43 3.61 2.37 62.2
220 340 280 280 3 1 2 720 5 580 47T443428-1 1 247 326 308 10 2.5 1 0.33 2.03 3.02 1.98 95.1
220 340 305 305 3 4 2 910 5 940 47T443431 1 244 326 307 8 2.5 3 0.35 1.95 2.90 1.91 99.6
220.662 314.325 290.000 290.000 3.2 1.6 2 300 5 050 47T443129A 1 240 300 289 4.5 3.2 1.6 0.33 2.03 3.02 1.98 70
220.663 314.325 239.713 239.713 3.2 1.6 2 100 4 890 M244249D/210/210D 1 241 300 288 5 3.2 1.6 0.33 2.03 3.02 1.98 59
225 320 230 230 2 2.5 1 670 3 730 4TR225A 1 246 310 293 5 2 2 0.37 1.80 2.69 1.76 57
228.600 311.150 200.025 200.025 3.2 1.6 1 660 3 760 LM245149D/110/110D 1 247 297 287 5.5 3.2 1.6 0.33 2.03 3.02 1.98 41.8
230 315 190 190 2 2.5 1 510 3 470 47T463119 1 248 305 290 7.5 2 2 0.37 1.80 2.69 1.76 43
234.950 327.025 196.850 196.850 3.2 1.6 1 600 3 720 8576D/20/20D 1 255 313 299 5.5 3.2 1.6 0.41 1.66 2.47 1.62 50.1
235 325 240 240 2.5 1.5 2 200 5 310 47T473324 1 254 313 301 8.5 2 1.5 0.33 2.03 3.02 1.98 60.5
C 109 C 110
d 240 ∼ (260) mm

r ra
r1
W
uD ud uDa uda
Bearing No. 1)
2) Design
r r1 1) da Da S ra rb 2)
3)
(kg)
240 320 250 250 2 1 1 880 4 760 47T483225B 1 257 310 299 7.5 2 1 0.33 2.03 3.02 1.98 54.2
240 338 248 248 3 4 2 360 5 360 37248 1 259 324 312 8.5 2.5 3 0.39 1.74 2.59 1.70 68.4
240 338 248 248 3 4 2 360 5 360 37248/DP1 2 259 324 312 8.5 2.5 3 0.39 1.74 2.59 1.70 68.4
240 360 194 194 3 4 1 830 3 580 47248 1 272 346 327 8.5 2.5 3 0.32 2.12 3.15 2.07 66.5
240 360 214 214 3 2.5 2 170 4 340 47T483621 1 268 346 328 9 2.5 2.5 0.40 1.68 2.50 1.64 75.4
240 360 308.5 308.5 3 2.5 3 320 7 400 47T483631A 1 268 346 329 9.5 2.5 2.5 0.26 2.55 3.80 2.50 112
240 365 290 290 2 SP 2 870 5 930 47T483729 1 265 355 333 9 2 0.8 0.46 1.47 2.19 1.44 108
240 410 270 270 4 2.5 3 220 5 520 47T484127A 1 281 392 369 8.5 3 2 0.40 1.68 2.50 1.64 144
241.478 349.148 228.600 228.600 3.2 1.6 2 190 4 920 47T483523A 1 267 335 319 8.5 3.2 1.6 0.35 1.91 2.84 1.86 72.9
241.478 349.148 228.600 228.600 3.2 1.6 1 900 4 100 EE127097D/135/136D 1 267 335 319 5.5 3.2 1.6 0.35 1.91 2.84 1.86 70.4
244.475 327.025 193.675 193.675 3.2 1.6 1 470 3 500 47T493319 1 259 313 303 5.5 3.2 1.6 0.55 1.24 1.84 1.21 44.4
244.475 327.025 193.675 193.675 3.2 1.6 1 570 3 780 LM247748D/710/710D 1 265 313 305 7.5 3.2 1.6 0.32 2.10 3.13 2.06 44.4
244.475 381.000 304.800 304.800 4.8 3.2 2 700 5 870 EE126096D/150/151D 1 269 364 336 6 4.8 3.2 0.52 1.31 1.95 1.28 129
247.650 400.050 253.995 249.235 6.4 1.6 2 600 5 140 EE220975D/1575/1576D 1 292 379 359 7.5 6.4 1.6 0.39 1.71 2.54 1.67 123
250 350 240 240 2.5 1 2 180 4 970 47T503524 1 270 338 324 6 2 1 0.40 1.68 2.50 1.64 70
250 365 270 270 3 1.5 2 650 6 340 47T503627 1 277 351 330 8 2.5 1.5 0.33 2.03 3.02 1.98 96.7
254.000 358.775 147.000 147.000 3.2 1.6 1 320 2 910 47T513615 1 290 345 331 7 3.2 1.6 0.33 2.03 3.02 1.98 46.9
254.000 358.775 269.875 269.875 3.2 1.6 2 650 6 340 47T513627A 2 277 345 330 8 3.2 1.6 0.33 2.03 3.02 1.98 85.8
254.000 358.775 269.875 269.875 3.2 1.6 2 630 6 030 47T513627B 1 272 345 331 7.5 3.2 1.6 0.46 1.47 2.19 1.44 85.5
254.000 358.775 269.875 269.875 3.2 1.6 2 630 6 030 47T513627C 2 272 345 331 7.5 3.2 1.6 0.46 1.47 2.19 1.44 86.1
254.000 358.775 269.875 269.875 3.2 3.2 2 650 6 340 M249748D/710/710D 1 277 345 330 8 3.2 3.2 0.33 2.03 3.02 1.98 86
260 360 272 272 3 1 2 910 7 020 47T523627A 1 280 346 335 9 2.5 1 0.33 2.03 3.02 1.98 83.6
260 368 268 268 4 5 2 510 6 020 37252 1 286 350 338 6 3 4 0.33 2.03 3.02 1.98 88.4
260 400 220 220 4 1.5 2 390 4 520 47T524022 1 295 382 364 7.5 3 1.5 0.40 1.68 2.50 1.64 98.5
260 400 255 255 7.5 5 2 620 5 400 47T524026 1 296 400 360 9 6 4 0.39 1.72 2.56 1.68 113
260 400 320 320 4 5 3 270 7 070 47T524032 1 294 382 361 8.5 3 4 0.33 2.03 3.02 1.98 145
[Notes] 1) While
SP indicates the specially
metric series chamfered
bearings have minusform.
tolerances for bore and OD, inch series have plus tolerances. Refer 3)
2) r b indicates the shaft chamfer dimension corresponding to cone chamfer dimension r 1 .
2) While metric
to page C 82series bearings
for details have minus
of applicable tolerances
tolerance for bore and OD, inch series have plus tolerances. Refer
standards.
C 111 C 112
d (260) ∼ 288.925 mm
r ra
r1
W
uD ud uDa uda
260 440 300 300 4 5 3 470 6 880 47352 1 311 422 392 10 3 4 0.35 1.95 2.90 1.91 188
260.350 422.275 317.500 314.325 3.2 6.4 3 470 6 720 HM252348D/310/310D 1 304 407 384 1 3.2 6.4 0.33 2.03 3.02 1.98 167
266.700 335.600 228.600 230.188 3.2 1.6 1 850 5 260 47T533423 1 281 322 312 7 3.2 1.6 0.28 2.43 3.61 2.37 46.4
266.700 355.600 228.600 230.188 3.2 1.6 2 230 5 690 47T533623B 1 285 342 332 8 3.2 1.6 0.36 1.87 2.79 1.83 62.7
266.700 355.600 228.600 230.188 3.2 1.6 1 980 4 830 76589D/20/20D 1 285 342 331 7 3.2 1.6 0.37 1.83 2.73 1.79 59.8
266.700 393.700 269.878 269.878 6.4 1.6 2 990 6 460 47T533927-1 1 294 373 361 8.5 6.4 1.6 0.40 1.68 2.50 1.64 112
269.875 381.000 282.575 282.575 3.2 3.2 2 930 6 690 M252349D/310/310D 1 291 367 350 6 3.2 3.2 0.33 2.03 3.02 1.98 98.4
270 364 260 260 3 1.5 2 370 5 720 47T543626 1 285 350 338 4.5 2.5 1.5 0.42 1.59 2.37 1.56 72.8
270 410 222 222 4 5 2 250 4 380 47254 1 308 392 372 6.5 3 4 0.27 2.51 3.74 2.45 100
276.225 393.700 269.878 269.878 6.4 1.6 2 730 5 830 47T553927 1 299 373 363 4.5 6.4 1.6 0.40 1.68 2.50 1.64 101
279.400 393.700 269.875 269.875 6.4 1.6 2 660 5 990 47T563927A 2 305 373 363 9.5 6.4 1.6 0.40 1.68 2.50 1.64 101
279.400 393.700 269.875 269.875 6.4 1.6 2 660 5 990 47T563927B 1 305 373 363 9.5 6.4 1.6 0.40 1.68 2.50 1.64 101
279.400 410.000 310.000 310.000 6.4 1.6 3 120 7 290 47T564131 2 308 389 374 8 6.4 1.6 0.40 1.68 2.50 1.64 140
279.578 380.898 244.475 244.475 3.2 1.6 2 280 5 650 LM654644D/610/610D 1 303 367 356 6.5 3.2 1.6 0.43 1.57 2.34 1.53 80.4
280 380 290 290 2 2 2 810 6 940 47T563829 1 300 370 354 6 2 2 0.33 2.03 3.02 1.98 91.8
280 380 290 290 2 1 2 810 6 940 47T563829A 2 300 370 354 6 2 1 0.33 2.03 3.02 1.98 92.1
280 395 288 288 4 2 2 880 6 900 37256X 1 303 377 363 8 3 2 0.40 1.68 2.50 1.64 110
280 395 288 288 4 2 2 880 6 900 47T564029A 2 303 377 363 8 3 2 0.40 1.68 2.50 1.64 110
280 420 225 225 4 5 2 390 4 950 47256 1 322 402 382 8.5 3 4 0.25 2.69 4.00 2.63 104
280 460 324 324 5 6 4 300 8 230 47T564632 1-P 321 438 415 10.5 4 5 0.46 1.47 2.19 1.44 214
280.268 379.887 244.475 244.475 3.2 1.6 2 280 5 650 47T563824 1 303 366 355 6.5 3.2 1.6 0.43 1.57 2.34 1.53 80
285.750 380.898 244.475 244.475 3.2 1.6 2 280 5 650 LM654648D/610/610D 1 303 367 356 6.5 3.2 1.6 0.43 1.57 2.34 1.53 75.6
288.925 406.400 298.450 298.450 3.2 3.2 3 450 8 840 M255449D/410/410D 1 316 392 373 9 3.2 3.2 0.34 2.00 2.97 1.95 127
C 113 C 114
d 292.100 ∼ (320) mm

r ra
r1
W
uD ud uDa uda
Bearing No. 1)
2) Design
3)
(kg)
292.100 422.275 269.875 269.875 3.2 6.4 3 170 6 830 EE330116D/166/167D 1 321 407 387 7.5 3.2 6.4 0.32 2.11 3.14 2.06 124
300 420 310 310 3 1 3 390 8 050 47T604231 1 325 406 388 8.5 2.5 1 0.34 2.00 2.98 1.96 132
300 424 310 310 4 5 3 000 6 570 37260 1 334 406 391 6 3 4 0.28 2.37 3.53 2.32 134
300 430 300 300 3 4 3 320 7 630 47T604330 1 328 416 393 10 2.5 3 0.35 1.95 2.90 1.91 141
300 430 310 310 3 2.5 3 520 8 420 47T604331 1 332 416 399 10 2.5 2 0.40 1.68 2.50 1.64 146
300 460 248 248 4 1.5 3 060 6 300 47T604625 1 342 442 416 8.5 3 1.5 0.40 1.68 2.50 1.64 149
300 460 360 360 4 5 4 300 9 550 47T604636 1 339 442 416 9 3 4 0.33 2.03 3.02 1.98 220
300 470 270 270 4 5 3 500 6 440 47T604727A 1 338 452 426 8 3 4 0.40 1.68 2.50 1.64 165
300 470 292 292 4 SP 3 980 7 870 47T604729B 1-P 341 452 428 8.5 3 2 0.40 1.68 2.50 1.64 193
300 470 292 292 4 1.5 4 120 8 210 47T604729C 1-P 343 452 428 9.5 3 1.5 0.33 2.03 3.02 1.98 198
300 500 350 350 4 2.5 5 010 9 290 47T605035 1 346 482 451 8 3 2 0.40 1.68 2.50 1.64 270
300.038 422.275 311.150 311.150 3.2 3.2 3 390 8 050 HM256849D/810/810D 1 325 407 388 7 3.2 3.2 0.34 2.00 2.98 1.96 136
304.648 438.048 279.400 280.990 4.8 3.2 3 230 6 980 47T614428C 2 331 420 403 7 4.8 3.2 0.47 1.44 2.15 1.41 133
304.648 438.048 279.400 280.990 4.8 3.2 3 230 6 980 M757448D/410/410D 1 331 420 403 7 4.8 3.2 0.47 1.44 2.15 1.41 132
304.800 419.100 269.875 269.875 6.4 1.6 2 840 6 950 M257149D/110/110D 1 331 398 387 7 6.4 1.6 0.33 2.03 3.02 1.98 110
304.800 482.600 377.825 365.125 6.4 3.2 4 820 9 800 47T614838A 1-P 343 461 437 1 6.4 3.2 0.47 1.43 2.12 1.40 250
304.800 495.300 349.250 342.900 6.4 3.2 4 370 9 370 EE724121D/195/196D 1 355 474 438 7 6.4 3.2 0.40 1.68 2.50 1.64 267
304.902 412.648 266.7 266.7 3.2 3.2 2 990 7 280 M257248D/210/210D 1 328 398 383 7 3.2 3.2 0.32 2.12 3.15 2.07 101
310 430 310 310 3 3 3 520 8 420 47T624331A 1 332 416 399 10 2.5 2.5 0.40 1.68 2.50 1.64 135
310 460 325 325 4 5 4 200 9 500 47T6246A 1 346 442 421 12 3 4 0.32 2.12 3.15 2.07 188
317.500 422.275 269.875 269.875 3.2 1.6 2 930 7 450 LM258649D/610/610D 1 341 407 392 8.5 3.2 1.6 0.32 2.12 3.15 2.07 104
317.500 447.675 327.025 327.025 6.4 1.6 4 120 9 820 47T644533J 1-P 341 426 411 7.5 6.4 1.6 0.33 2.02 3.00 1.97 161
317.500 447.675 327.025 327.025 6.4 1.6 4 280 10 100 47T644533L 1 344 426 411 11.5 6.4 1.6 0.33 2.03 3.02 1.98 161
320 440 335 335 2 2.5 3 590 8 750 47T644434 1 341 430 408 5.5 2 2 0.40 1.68 2.50 1.64 149
[Notes] 1) While metric series
SP indicates bearings
the specially have minus
chamfered tolerances for bore and OD, inch series have plus tolerances. Refer
form. 2) r b indicates the shaft chamfer dimension corresponding to cone chamfer dimension r 1 .
3)
to page
2) While C 82series
metric for details of applicable
bearings have minus tolerance standards.
tolerances for bore and OD, inch series have plus tolerances. Refer
C 115 C 116
d (320) ∼ (355.600) mm
r ra
r1
W
uD ud uDa uda
320 460 325 325 4 2.5 4 030 9 420 47T644633 1 349 442 424 10 3 2.5 0.42 1.62 2.42 1.59 175
320 460 338 338 4 5 3 500 8 590 37264 1 356 442 421 8.5 3 4 0.33 2.03 3.02 1.98 183
320 480 254 254 4 2.5 3 400 6 940 47T644825 1-P 358 462 437 9 3 2 0.40 1.68 2.50 1.64 161
320 480 260 260 4 5 3 360 6 890 47T644826 1 359 462 437 11.5 3 5 0.40 1.68 2.50 1.64 165
320 480 360 360 4 1 4 970 11 000 47T644836-1 1-P 352 462 442 9 3 1 0.47 1.43 2.12 1.40 229
320 500 380 380 4 1.5 5 540 11 900 47T645038 1-P 363 482 454 11.5 3 1.5 0.33 2.03 3.02 1.98 284
320 540 364 364 5 6 5 380 10 600 47364 1 376 518 479 8.5 4 5 0.32 2.12 3.15 2.07 340
325 430 230 230 3 1 2 410 5 800 47T654323 1 347 416 401 8.5 2.5 1 0.40 1.68 2.50 1.64 88.5
327 445 230 230 3 1 2 620 6 080 47T654523 1 353 431 413 9 2.5 1 0.40 1.68 2.50 1.64 102
330.200 444.500 301.625 301.625 3.2 3.2 3 550 9 260 47T664430 1 357 430 414 10 3.2 3.2 0.26 2.55 3.80 2.50 134
330.200 508.000 307.975 307.975 6.4 1.6 4 320 8 500 47T665131A 1 372 486 462 8 6.4 1.6 0.33 2.03 3.02 1.98 219
335.000 460.000 342.900 342.900 3.2 1.6 3 960 9 390 47T674634/DP 2 361 445 428 7.5 3.2 1.6 0.40 1.68 2.50 1.64 165
337.375 469.900 342.900 342.900 3.2 1.6 4 630 11 400 HM261049D/010/010D 1-P 360 455 432 9 3.2 1.6 0.33 2.02 3.01 1.97 190
340 480 350 350 5 6 4 700 11 700 37268A 1-P 371 458 443 9.5 4 6 0.33 2.03 3.02 1.98 198
340 520 278 278 5 6 4 040 8 110 47T685228 1 384 498 473 9 4 6 0.40 1.68 2.50 1.64 212
340 520 323 323 5 6 4 380 8 930 47T685232 1 381 498 473 10 4 5 0.40 1.68 2.50 1.64 242
343.052 457.098 254.000 254.000 3.2 1.6 2 850 6 950 47T694625 1 363 442 425 6 3.2 1.6 0.47 1.43 2.12 1.40 111
343.052 457.098 254.000 254.000 3.2 1.6 2 850 6 950 47T694625/DP3 2 363 442 425 6 3.2 1.6 0.47 1.43 2.12 1.40 111
346.075 488.950 358.775 358.775 3.2 3.2 4 620 11 600 HM262749D/10/10D 1 378 474 449 8 3.2 3.2 0.33 2.02 3.00 1.97 214
347.663 469.900 292.100 292.100 3.2 3.2 3 600 9 040 M262449D/10/10D 1 374 455 436 10 3.2 3.2 0.33 2.03 3.02 1.98 145
355 490 316 316 2 2.5 4 160 10 000 47T714932 1 385 480 455 12.5 2 2 0.33 2.03 3.02 1.98 180
355.600 482.600 269.875 265.113 3.2 1.6 3 390 7 860 47T714827-1 1 386 468 450 8 3.2 1.6 0.26 2.55 3.80 2.50 139
355.600 482.600 269.875 265.112 3.2 1.6 3 060 7 020 LM763449D/410/410D 1 381 468 450 3.5 3.2 1.6 0.47 1.43 2.14 1.40 136
C 117 C 118
d (355.600) ∼ (380) mm
r ra
r1
W
uD ud uDa uda
355.600 488.950 317.500 317.500 3.2 1.6 4 370 10 900 M263349D/310/310D 1-P 383 474 452 7.5 3.2 1.6 0.33 2.03 3.02 1.98 182
360 480 375 375 3 4 3 930 9 910 47T724838A 1 383 466 446 3.5 2.5 3 0.40 1.68 2.50 1.64 177
360 480 375 375 3 1 4 190 11 100 47T724838C 1 381 466 448 5 2.5 1 0.33 2.03 3.02 1.98 183
360 508 370 370 5 6 4 840 11 500 47T725137 1 392 486 471 7 4 6 0.33 2.03 3.02 1.98 232
360 520 370 370 5 6 4 920 11 400 47T725237 1 395 498 476 8.5 4 5 0.33 2.03 3.02 1.98 259
360 520 410 410 5 6 5 970 14 300 47T725241 1-P 395 498 479 8.5 4 5 0.33 2.03 3.02 1.98 292
360 540 280 280 5 6 3 790 7 820 47272 1 406 518 490 10 4 5 0.32 2.12 3.15 2.07 221
360 540 280 280 5 6 3 760 8 000 47T725428 1 402 518 489 10.5 4 5 0.55 1.24 1.84 1.21 224
360 540 460 460 4 5 6 440 15 800 47T7254 1 408 522 492 9.5 3 4 0.27 2.47 3.67 2.41 373
368.300 523.875 382.588 382.588 6.4 3.2 5 530 13 600 47T745238B 1-P 404 502 483 9 6.4 3.2 0.29 2.32 3.45 2.26 269
368.300 523.875 382.588 382.588 3.2 1.6 5 620 14 100 47T745238D 1 403 508 483 7.5 3.2 1.6 0.33 2.03 3.02 1.98 265
368.300 523.875 382.588 382.588 6.4 3.2 5 920 14 500 47T745238J 1-P 401 502 485 10.5 6.4 3.2 0.33 2.03 3.02 1.98 268
368.300 523.875 382.588 382.588 6.4 3.2 5 460 13 600 HM265049D/010/010D 1-P 403 502 483 7 6.4 3.2 0.33 2.03 3.02 1.98 269
368.300 563.000 382.588 382.588 6.4 3.2 6 300 13 600 47T745638 1-P 417 541 516 10.5 6.4 3.2 0.29 2.32 3.45 2.26 344
370 516 346 346 4 1.5 4 880 11 700 47T745235 1-P 398 498 479 9 3 1.5 0.40 1.68 2.50 1.64 216
374.650 501.650 260.350 260.350 3.2 1.6 2 930 7 750 47T745026 1 399 486 459 7 3.2 1.6 0.43 1.56 2.32 1.52 145
380 520 360 360 5 6 4 610 12 200 47T765236 1 417 498 484 11 4 5 0.32 2.12 3.15 2.07 225
380 520 400 400 4 2.5 5 020 13 000 47T765240 1 404 502 482 9.5 3 2 0.40 1.68 2.50 1.64 248
380 536 390 390 5 6 5 760 12 900 37276 1 415 514 496 7.5 4 5 0.40 1.68 2.50 1.64 268
380 560 282 282 5 6 3 670 7 580 47276 1 429 538 511 9 4 5 0.27 2.47 3.67 2.41 232
380 560 285 285 4 5 4 600 10 000 47T765629 1-P 428 542 513 11 3 4 0.27 2.47 3.67 2.41 246
380 560 285 285 4 5 4 420 9 240 47T765629A 1 427 542 515 11 3 5 0.27 2.47 3.67 2.41 244
380 560 325 325 5 6 5 330 11 900 47T765633A 1-P 427 538 514 11 4 5 0.27 2.47 3.67 2.41 278
380 560 360 390 4 1.5 5 310 11 800 47T765639 1 422 542 514 9 3 1.5 0.35 1.95 2.90 1.91 307
380 560 370 370 5 6 5 910 13 600 47T765637 1-P 423 538 515 10 4 5 0.33 2.03 3.02 1.98 312
380 580 500 500 5 6 7 410 17 500 47T765850 1 427 558 529 10.5 4 5 0.33 2.03 3.02 1.98 478
C 119 C 120
d (380) ∼ 430 mm
r ra
r1
W
uD ud uDa uda
380 620 400 400 5 6 6 130 12 700 47376 1 445 598 552 6.5 4 5 0.32 2.12 3.15 2.07 476
380 620 418.5 418.5 5 6 7 080 14 000 47T766242 1-P 435 598 561 10 4 5 0.46 1.47 2.19 1.44 499
384.175 546.100 400.050 400.050 6.4 3.2 6 530 16 900 HM266449D/410/410D 1-P 418 524 502 10.5 6.4 3.2 0.33 2.03 3.02 1.98 315
384.175 546.100 470.000 470.000 6.4 3.2 6 220 16 200 47T775547 1 418 524 503 7.5 6.4 3.2 0.33 2.03 3.02 1.98 360
390 510 350 350 3 1.5 4 300 11 700 47T785135A 1 413 496 478 10.5 2.5 1.5 0.33 2.03 3.02 1.98 186
390 510 350 350 3 1 4 150 11 200 47T785135B 1 415 496 479 5.5 2.5 1 0.29 2.32 3.45 2.26 183
395 545 288.7 270.3 7.5 5 3 330 7 680 47T795529 1 433 509 494 3 6 4 0.43 1.57 2.34 1.53 190
400 560 380 380 4 1.5 5 970 15 200 47T805638A 1-P 435 542 519 10 3 1.5 0.33 2.03 3.02 1.98 296
400 564 412 412 4 2.5 6 470 16 500 47T805641 1-P 432 546 522 9 3 2.5 0.40 1.68 2.50 1.64 329
400 590 304 304 4 1.5 4 760 10 200 47T805930A 1-P 449 572 540 7.5 3 1.5 0.33 2.03 3.02 1.98 289
400 600 308 308 5 6 4 810 9 930 47280 1 452 578 548 9 4 5 0.33 2.03 3.02 1.98 310
406.400 546.100 288.925 288.925 6.4 1.6 3 960 9 540 47T815529 1 435 524 509 9.5 6.4 1.6 0.47 1.43 2.12 1.40 184
406.400 546.100 330.000 330.000 6.4 3.2 4 800 12 400 47T815533B 1-P 434 524 509 8.5 6.4 3.2 0.40 1.68 2.50 1.64 214
406.400 562.000 381.000 381.000 6.4 3.2 5 990 15 000 47T815638 1 439 540 524 9.5 6.4 3.2 0.33 2.03 3.02 1.98 284
406.400 565.150 381.000 381.000 6.4 3.2 5 990 15 000 M267949D/910/910XD 1 438.3 544 524 9.5 6.4 3.2 0.33 2.03 3.02 1.98 291
409.575 546.100 334.963 334.963 6.4 1.6 4 570 11 500 M667947D/911/911D 1 432 524 509 8.5 6.4 1.6 0.42 1.62 2.42 1.59 213
415.925 590.550 434.975 434.975 6.4 3.2 7 060 18 800 47T835943A 1-P 455 568 543 10 6.4 3.2 0.33 2.03 3.02 1.98 391
420 560 370 370 5 6 4 950 13 600 47T845637 1 459 538 527 12 4 5 0.32 2.12 3.15 2.07 252
420 560 437 437 4 1.5 5 620 14 900 47T845644 1 450 542 526 4 3 1.5 0.26 2.55 3.80 2.50 283
420 592 432 432 5 6 6 030 15 700 37284 1 460 570 544 7.5 4 5 0.33 2.03 3.02 1.98 374
420 620 312 312 5 6 4 810 10 400 47284 1 473.5 598 567 10 4 5 0.33 2.03 3.02 1.98 328
420 650 460 460 6 6 8 560 18 300 47T846546 1 468 622 595 8.5 5 5 0.40 1.68 2.50 1.64 558
430 570 336 336 4 1.5 4 790 12 500 47T865734C 1 460 552 536 10 3 1.5 0.36 1.87 2.79 1.83 232
430 570 380 380 4 1.5 5 640 15 900 47T865738 1 463 552 534 10.5 3 1.5 0.26 2.55 3.80 2.50 269
C 121 C 122
d 431.800 ∼ 475.000 mm

r ra
r1
W
uD ud uDa uda
431.800 571.500 336.550 336.550 6.4 1.6 5 070 13 500 47T865734 1-P 460 549 534 10 6.4 1.6 0.36 1.87 2.79 1.83 232
431.800 571.500 336.550 336.550 6.4 1.6 4 290 11 300 LM769349D/310/310D 1 463 549 534 7 6.4 1.6 0.48 1.41 2.10 1.38 231
431.800 635.000 355.600 355.600 6.4 6.4 6 310 13 700 EE931170D/250/251XD 1-P 481 612 586 8 6.4 6.4 0.32 2.10 3.13 2.06 385
432.003 609.524 317.500 317.500 6.4 3.6 5 210 12 100 EE736173D/238/239D 1-P 474 586 562 9 6.4 3.6 0.35 1.94 2.89 1.90 291
440 580 420 420 4 1.5 5 730 15 400 47T885842 1-P 467 562 544 1.5 3 1.5 0.26 2.55 3.80 2.50 288
440 620 454 454 6 6 7 110 17 500 37288 1 482 592 576 9 5 5 0.40 1.68 2.50 1.64 417
440 620 454 454 4 5 7 610 19 800 47T886246 1-P 474 602 573 10.5 3 5 0.40 1.68 2.50 1.64 436
440 635 430 430 5 6 7 560 18 000 47T886443 1-P 485 613 587 9.5 4 5 0.33 2.03 3.02 1.98 450
440 635 470 470 5 2.5 8 510 20 900 47T886447 1-P 483 613 588 10.5 4 2 0.33 2.03 3.02 1.98 500
440 650 326 326 6 6 5 080 11 000 47288 1-P 500 622 595 11 5 5 0.28 2.43 3.61 2.37 361
440 650 334 334 6 6 5 490 12 200 47288A 1 500 622 595 9.5 5 5 0.28 2.43 3.61 2.37 375
440 660 450 450 5 2 8 690 19 000 47T886645 1 489 638 610 9.5 4 2 0.32 2.12 3.15 2.07 532
447.675 635.000 463.550 463.550 6.4 3.2 7 860 21 000 M270749D/710/710D 1-P 491 612 584 8 6.4 3.2 0.33 2.03 3.02 1.98 472
449.949 594.949 368.000 368.000 5 2.5 5 980 16 200 M270449D/10/10D 1-P 478 573 557 9 5 2 0.33 2.03 3.02 1.98 278
450 580 450 450 6 1.5 5 130 14 600 47T905845 1 475 552 537 2 5 1.5 0.26 2.55 3.80 2.50 286
457.200 596.900 279.400 276.225 3.2 1.6 4 260 11 400 47T916028A 1-P 485 581 560 8.5 3.2 1.6 0.47 1.43 2.12 1.40 307
457.200 660.400 323.847 323.850 6.4 3.2 5 700 12 700 EE737179D/260/261D 1-P 501 637 603 9 6.4 3.2 0.37 1.80 2.69 1.76 365
460 586 280 280 3 1 3 710 9 810 47T925928 1 483 572 555 10.5 2.5 1 0.44 1.52 2.26 1.49 177
460 615 360 360 3 1 5 000 13 300 47T926236 1 490 601 572 8 2.5 1 0.47 1.43 2.12 1.40 292
460 625 421 421 4 1.5 6 920 18 800 47T926342 1-P 495 607 582 8 3 1.5 0.33 2.03 3.02 1.98 386
460 650 474 474 6 6 7 680 19 400 37292 1 500 622 598 8 5 5 0.33 2.03 3.02 1.98 495
460 680 375 375 5 2 6 500 15 200 47T926838 1 515 658 618 10.5 4 2 0.36 1.87 2.79 1.83 475
460 730 440 440 6 3 8 650 17 700 47T927344 1-P 519 702 662 13 5 2.5 0.47 1.43 2.12 1.40 710
475.000 600.000 368.000 368.000 4.8 1.6 4 970 15 100 47T956037A 1 501 581 566 10.5 4.8 1.6 0.26 2.55 3.80 2.50 246
C 123 C 124
d 479.425 ∼ 500 mm

r ra
r1
W
uD ud uDa uda
Bearing No. 1)
2) Design
3)
(kg)
479.425 679.450 495.300 495.300 6.4 3.2 9 660 25 400 47T966850 1-P 523 656 641 12.5 6.4 3.2 0.33 2.03 3.02 1.98 591
479.425 679.450 495.300 495.300 6.4 3.2 8 480 22 200 M272749D/710/710D 1-P 524 656 627 7.5 6.4 3.2 0.33 2.03 3.02 1.98 575
480 678 494 494 6 6 9 160 23 300 37296 1-P 520 650 629 9.5 5 5 0.33 2.03 3.02 1.98 563
480 700 390 390 5 6 7 400 16 800 47T967039 1-P 536 678 647 11 4 6 0.33 2.03 3.02 1.98 508
480.000 700.000 420.000 420.000 6.4 3.2 8 060 18 800 47T967042C 1 531 677 644 10.5 6.4 3.2 0.35 1.95 2.90 1.91 540
482.600 615.950 330.200 330.200 6.4 6.4 4 830 13 400 47T976233 2-P 512 593 573 6 6.4 6.4 0.44 1.54 2.30 1.51 240
482.600 615.950 330.200 330.200 6.4 6.4 4 830 13 400 4TR19A 1-P 512 593 573 6.5 6.4 6.4 0.44 1.54 2.30 1.51 240
482.600 615.950 330.200 330.200 6.4 4.8 5 270 15 000 4TR19B 1-P 509 593 573 10.5 6.4 4.8 0.33 2.03 3.02 1.98 243
482.600 615.950 330.200 330.200 6.4 3.2 5 210 15 000 4TR19D 1 508 593 573 10 6.4 3.2 0.36 1.87 2.79 1.83 240
482.600 615.950 420.000 420.000 4 2.5 5 810 16 700 47T976242 1 508 597 577 6 4 2.5 0.26 2.55 3.80 2.50 296
482.600 647.700 417.512 417.512 6.4 3.2 7 390 20 300 47T976542A 2-P 514 624 603 9.5 6.4 3.2 0.33 2.03 3.02 1.98 397
482.600 647.700 417.512 417.512 6.4 3.2 7 390 20 300 M272647D/610/610D 1-P 514 624 604 9.5 6.4 3.2 0.33 2.03 3.02 1.98 395
488.950 622.300 365.125 365.125 3.6 3.6 4 950 13 900 47T986236 1 516 605 585 7.5 3.6 3.6 0.33 2.03 3.02 1.98 262
488.950 660.400 361.950 365.125 6.4 7.9 6 200 15 800 EE640193D/260/261D 1-P 527 637 616 11 6.4 7.9 0.31 2.20 3.27 2.15 357
489.026 634.873 320.675 320.675 3.2 3.2 4 520 13 200 EE243193D/250/251D 1 526 618 595 9.5 3.2 3.2 0.34 1.97 2.93 1.93 263
489.026 634.873 320.675 320.675 3.2 3.2 4 930 13 700 LM772749D/710/710D 1 513 618 594 9.5 3.2 3.2 0.47 1.43 2.12 1.40 261
490 625 385 385 4 1.5 5 690 17 200 47T986339A 1 520 607 587 9.5 3 1.5 0.28 2.43 3.61 2.37 290
490 625 385 385 4 1.5 5 540 16 600 47T986339B 1 517 607 587 4.5 3 1.5 0.32 2.12 3.15 2.07 285
500 640 450 450 4 1.5 7 050 20 300 4TR500M 2-P 527 622 602 10.5 3 1.5 0.24 2.84 4.23 2.78 352
500 670 515 515 5 6 9 110 25 700 4TR500B 1-P 530 648 626 11 4 5 0.32 2.12 3.15 2.07 510
500 705 515 515 6 SP 9 530 24 500 372/500 1-P 544 677 651 8.5 5 6 0.37 1.80 2.69 1.76 641
500 710 430 425 5 3 8 170 20 000 4TR500T 1 547 688 658 12 4 3 0.37 1.80 2.69 1.76 528
500 720 400 400 6 6 7 990 18 700 4TR500J 1-P 552 692 663 12.5 5 5 0.33 2.03 3.02 1.98 547
500 760 420 420 2 6 8 730 19 300 4TR500Q 1-P 566 750 696 11.5 2 6 0.39 1.74 2.59 1.70 698
[Notes] 1) While
SP indicates the specially
metric series chamfered
bearings have minusform.
tolerances for bore and OD, inch series have plus tolerances. Refer 3)
2) r b indicates the shaft chamfer dimension corresponding to cone chamfer dimension r 1 .
2) While metric
to page C 82series bearings
for details have minus
of applicable tolerances
tolerance for bore and OD, inch series have plus tolerances. Refer
standards.
C 125 C 126
Sealed type four-row tapered roller bearings
d 75 ∼ 234.950 mm
T
r
r1
uD ud
Boundary dimensions Basic load ratings Con- Axial load factors (Refer.)
(kN)
Bearing No. Design stant Mass
d D T W r 1) r1 1)
(kg)
Cr C0r e Y2 Y3
mm 1/25.4 mm 1/25.4 mm 1/25.4 mm 1/25.4 min. min.
75 ⎯ 120 ⎯ 150 ⎯ 150 ⎯ 2 1 424 764 47TS151215 1 0.33 2.03 3.02 6.4
75 ⎯ 135 ⎯ 180 ⎯ 187 ⎯ 1.5 1.5 455 776 47TS151418 1 0.87 0.78 1.16 10.7
140 ⎯ 198 ⎯ 174 ⎯ 174 ⎯ 4 1 803 1 630 47TS282017 1 0.47 1.43 2.12 16.3
150 ⎯ 210 ⎯ 240 ⎯ 240 ⎯ 1.5 0.5 993 2 270 47TS302124 1 0.39 1.74 2.59 23.5
170 ⎯ 240 ⎯ 175 ⎯ 175 ⎯ 2.5 1.5 980 1 990 47TS342418 1 0.26 2.55 3.8 23.9
170 ⎯ 250 ⎯ 230 ⎯ 230 ⎯ 2.5 1.5 1 370 2 860 47TS342523 1 0.26 2.55 3.8 37.7
190.500 7.5000 266.700 10.5000 188.913 7.4375 187.325 7.3750 3.2 1 1 060 2 270 47TS382719A 1 0.46 1.47 2.19 27.6
195 ⎯ 270 ⎯ 250 ⎯ 250 ⎯ 2.5 1 1 420 3 550 47TS392725-1 1 0.4 1.68 2.5 43.6
200 ⎯ 300 ⎯ 300 ⎯ 300 ⎯ 4 1.6 2 260 4 900 47TS403030 1 0.26 2.55 3.8 73.5
203.200 8.0000 317.500 12.5000 266.700 10.5000 266.700 10.5000 5 1.6 2 060 4 010 47TS413227 1 0.4 1.68 2.5 76.8
206.375 8.1250 282.575 11.1250 190.500 7.5000 190.500 7.5000 3.2 1 1 100 2 240 47TS412819 1 0.51 1.33 1.97 33.5
206.375 8.1250 282.575 11.1250 240.000 9.4488 210.000 8.2677 3 1 1 450 3 380 47TS412824 1 0.43 1.57 2.34 39.6
215.900 8.5000 288.925 11.3750 177.800 7.0000 177.800 7.0000 3.2 1 1 060 2 350 47TS432918 1 0.4 1.68 2.5 30.6
220 ⎯ 295 ⎯ 315 ⎯ 315 ⎯ SP SP 1 540 3 910 47TS443032A 1 0.4 1.68 2.5 55.8
220 ⎯ 320 ⎯ 290 ⎯ 290 ⎯ 3 2 2 200 4 700 47TS443229B 1 0.39 1.74 2.59 73.9
220 ⎯ 330 ⎯ 260 ⎯ 260 ⎯ 5 2.5 2 100 4 220 47TS443326 1 0.4 1.68 2.5 79.5
220.663 8.6875 314.325 12.3750 239.713 9.4375 239.713 9.4375 3.2 3 1 680 3 410 47TS443124 1 0.33 2.03 3.02 51.9
220.663 8.6875 314.325 12.3750 330.000 12.9921 330.000 12.9921 3.2 3 2 360 5 650 47TS443133 1 0.26 2.55 3.8 79.2
225 ⎯ 320 ⎯ 230 ⎯ 230 ⎯ 3 1.5 1 630 3 350 47TS453223A 1 0.47 1.43 2.12 56.9
228.600 9.0000 311.150 12.2500 200.025 7.8750 200.025 7.8750 3.2 SP 1 330 2 850 47TS463120-1 1 0.4 1.68 2.5 41.3
234.950 9.2500 327.025 12.8750 196.850 7.7500 196.850 7.7500 3.2 1 1 490 3 310 47TS473320A 2 0.4 1.68 2.5 48.1
[Note] 1) SP indicates the specially chamfered form.
C 127 C 128
d 240 ∼ (280) mm
T
r
r1
uD ud
(kN)
d D T W r 1) r1 1)
(kg)
Cr C0r e Y2 Y3
mm 1/25.4 mm 1/25.4 mm 1/25.4 mm 1/25.4 min. min.
240 ⎯ 320 ⎯ 294 ⎯ 294 ⎯ 4 1 1 880 4 760 47TS483229-1 1 0.33 2.03 3.02 63.6
240 ⎯ 338 ⎯ 248 ⎯ 248 ⎯ 3 1.5 1 890 4 120 47TS483425B 1 0.47 1.43 2.12 66
240 ⎯ 338 ⎯ 290 ⎯ 290 ⎯ 3 1 2 360 5 360 47TS483429 1 0.39 1.74 2.59 78
240 ⎯ 338 ⎯ 320 ⎯ 320 ⎯ 3 1 2 430 5 890 47TS483432 1 0.28 2.43 3.61 87.3
240 ⎯ 338 ⎯ 340 ⎯ 340 ⎯ 3 1 2 450 5 930 47TS483434A 1 0.4 1.68 2.5 88
241.478 9.5070 349.148 13.7460 228.600 9.0000 228.600 9.0000 3.2 SP 2 000 4 110 47TS483523A 2 0.35 1.91 2.84 67.5
244.475 9.6250 327.025 12.8750 193.675 7.6250 193.675 7.6250 5 1.5 1 280 2 790 47TS493319 1 0.33 2.03 3.02 41.5
244.475 9.6250 381.000 15.0000 304.800 12.0000 304.800 12.0000 5 1.6 2 700 5 240 47TS493830 1 0.47 1.43 2.12 124
245 ⎯ 345 ⎯ 310 ⎯ 310 ⎯ 3 1.5 2 520 6 020 47TS493531-2 1 0.4 1.68 2.5 89.9
250 ⎯ 365 ⎯ 270 ⎯ 270 ⎯ 3 1.5 2 260 4 730 47TS503727A-1 1 0.4 1.68 2.5 94.2
254.000 10.0000 358.775 14.1250 269.875 10.6250 269.875 10.6250 3.2 1.6 2 130 4 760 47TS513627A-1 1 0.55 1.24 1.84 82
254.000 10.0000 358.775 14.1250 269.875 10.6250 269.875 10.6250 3.2 1.5 2 520 6 010 47TS513627B 2 0.4 1.68 2.5 85
260 ⎯ 365 ⎯ 340 ⎯ 340 ⎯ 3.5 1.6 2 800 6 530 47TS523734-5 1 0.4 1.68 2.5 110
260 ⎯ 370 ⎯ 354 ⎯ 354 ⎯ 4 1.5 3 100 7 410 47TS523735 1 0.26 2.55 3.8 120
266.700 10.5000 355.600 14.0000 228.600 9.0000 230.188 9.0625 3.2 1.6 1 940 4 880 47TS533623B 2 0.36 1.87 2.79 60
275 ⎯ 385 ⎯ 340 ⎯ 340 ⎯ 3 1.5 2 970 7 400 47TS553934 1 0.4 1.68 2.5 121
276.225 10.8750 393.700 15.5000 269.875 10.6250 269.875 10.6250 3.2 1.6 2 350 5 040 47TS553927-4 1 0.47 1.43 2.12 100
276.225 10.8750 393.700 15.5000 269.875 10.6250 269.875 10.6250 3.2 SP 2 770 6 510 47TS553927A 2 0.4 1.68 2.5 105
279.400 11.0000 393.700 15.5000 269.875 10.6250 269.875 10.6250 3.2 1.6 2 350 5 040 47TS563927 1 0.47 1.43 2.12 99.5
279.400 11.0000 393.700 15.5000 269.875 10.6250 269.875 10.6250 3.2 SP 2 770 6 510 47TS563927B 2 0.4 1.68 2.5 101
279.400 11.0000 393.700 15.5000 320.000 12.5984 320.000 12.5984 3.2 1.5 2 880 6 900 47TS563932-2 1 0.4 1.68 2.5 124
279.578 11.0070 380.898 14.9960 244.475 9.6250 244.475 9.6250 3.2 SP 2 270 5 360 47TS563824 2 0.4 1.68 2.5 78.3
280 ⎯ 380 ⎯ 290 ⎯ 290 ⎯ 3.2 SP 2 720 6 940 47TS563829A 2 0.33 2.03 3.02 93.8
C 129 C 130
d (280) ∼ 317.500 mm
T
r
r1
uD ud
(kN)
d D T W r 1) r1 1)
(kg)
Cr C0r e Y2 Y3
mm 1/25.4 mm 1/25.4 mm 1/25.4 mm 1/25.4 min. min.
280 ⎯ 395 ⎯ 290 ⎯ 290 ⎯ 3 2.5 2 640 5 940 47TS564029 1 0.4 1.68 2.5 110
280 ⎯ 395 ⎯ 340 ⎯ 340 ⎯ 3 1.5 2 960 7 110 47TS564034A 1 0.4 1.68 2.5 130
280 ⎯ 410 ⎯ 268 ⎯ 268 ⎯ 5.4 1.6 2 240 4 510 47TS564127 1 0.33 2.03 3.02 118
280 ⎯ 412 ⎯ 340 ⎯ 340 ⎯ 4 2 3 350 7 220 47TS564134 1 0.28 2.43 3.61 154
280 ⎯ 430 ⎯ 350 ⎯ 350 ⎯ 3.5 1.5 3 940 8 190 47TS564335 1 0.4 1.68 2.5 178
285 ⎯ 400 ⎯ 340 ⎯ 340 ⎯ 3 1.5 3 190 7 610 47TS574034 1 0.4 1.68 2.5 131
285.750 11.2500 380.898 14.9960 244.475 9.6250 244.475 9.6250 3.2 1 2 000 4 600 47TS573824A 1 0.43 1.57 2.34 73.2
290 ⎯ 400 ⎯ 346 ⎯ 346 ⎯ 4 1.5 3 070 7 860 47TS584035 1 0.4 1.68 2.5 128
290 ⎯ 400 ⎯ 420 ⎯ 420 ⎯ 4 1.5 3 070 7 860 47TS584042C 1 0.4 1.68 2.5 155
290 ⎯ 420 ⎯ 380 ⎯ 380 ⎯ 3 1.2 3 640 8 260 47TS584238 1 0.4 1.68 2.5 175
290 ⎯ 450 ⎯ 415 ⎯ 415 ⎯ 4 1.5 4 460 9 460 47TS584542 1 0.47 1.43 2.12 238
300 ⎯ 400 ⎯ 254 ⎯ 254 ⎯ 4 5 2 220 5 300 47TS604025 1 0.28 2.43 3.61 84.6
300 ⎯ 420 ⎯ 310 ⎯ 310 ⎯ 4 3.5 2 890 6 670 47TS604231 1 0.4 1.68 2.5 128
304.648 11.9940 438.048 17.2460 279.400 11.0000 280.990 11.0626 4 1.6 2 570 5 380 47TS614428B-10 1 0.47 1.44 2.15 135
304.648 11.9940 438.048 17.2460 279.400 11.0000 279.400 11.0000 3.2 1.6 3 140 6 860 47TS614428C-1 2 0.4 1.68 2.5 135
304.800 12.0000 419.100 16.5000 269.875 10.6250 269.875 10.6250 6.4 2 2 490 5 420 47TS614227 1 0.33 2.03 3.02 100
304.800 12.0000 501.650 19.7500 336.550 13.2500 296.550 11.6752 4 4 4 280 8 570 47TS615034 1-P 0.33 2.03 3.02 257
304.902 12.0040 412.648 16.2460 266.700 10.5000 266.700 10.5000 3.2 0.8 2 750 6 820 47TS614127D 2 0.39 1.74 2.59 99.5
310 ⎯ 430 ⎯ 310 ⎯ 310 ⎯ 3 1 3 010 6 880 47TS624331-4 1 0.4 1.68 2.5 131
310 ⎯ 430 ⎯ 350 ⎯ 350 ⎯ 3.5 1.5 3 280 7 870 47TS624335A 1 0.4 1.68 2.5 148
310 ⎯ 430 ⎯ 350 ⎯ 350 ⎯ 3.5 SP 3 280 7 870 47TS624335B-2 1 0.4 1.68 2.5 148
310 ⎯ 457.098 ⎯ 390 ⎯ 390 ⎯ 4 1.5 4 200 9 500 47TS624639 1 0.32 2.12 3.15 220
317.500 12.5000 447.675 17.6250 367.000 14.4488 367.000 14.4488 4 1.6 3 680 8 500 47TS644537-1 1 0.4 1.68 2.5 176
C 131 C 132
d 320 ∼ 410 mm
T
r
r1
uD ud
(kN)
d D T W r 1) r1 1)
(kg)
Cr C0r e Y2 Y3
mm 1/25.4 mm 1/25.4 mm 1/25.4 mm 1/25.4 min. min.
320 ⎯ 440 ⎯ 335 ⎯ 335 ⎯ 4 1 3 140 7 330 47TS644434 1 0.4 1.68 2.5 146
320 ⎯ 480 ⎯ 360 ⎯ 360 ⎯ 4 1.5 4 210 8 800 47TS644836B 1-P 0.47 1.43 2.12 220
320 ⎯ 480 ⎯ 420 ⎯ 420 ⎯ 4 1.5 5 470 12 100 47TS644842 1-P 0.26 2.55 3.8 262
330.302 13.0040 438.023 17.2450 254.000 10.0000 247.650 9.7500 3.2 1.6 2 190 4 960 47TS664425 1 0.46 1.47 2.19 95.8
335.000 13.1890 460.000 18.1102 342.900 13.5000 342.900 13.5000 3.3 1.5 3 740 9 290 47TS674634A 1 0.4 1.68 2.5 167
342.875 13.4990 488.900 19.2480 410.000 16.1417 410.000 16.1417 4 2 4 620 11 600 47TS684941 1 0.33 2.02 3 233
342.875 ⎯ 560 ⎯ 500 ⎯ 500 ⎯ 5 2.5 7 210 15 000 47TS685650 1-P 0.33 2.03 3.02 495
343.052 13.5060 457.098 17.9960 254.000 10.0000 254.000 10.0000 3.2 0.8 2 870 7 030 47TS694625D-1 2 0.4 1.68 2.5 110
343.052 13.5060 457.098 17.9960 299.000 11.7717 299.000 11.7717 3.2 SP 3 310 9 010 47TS694630B 2 0.4 1.68 2.5 135
346.075 13.6250 488.950 19.2500 358.775 14.1250 358.775 14.1250 4 2 3 780 8 310 47TS694936 1 0.33 2.03 3.02 210
350 ⎯ 480 ⎯ 420 ⎯ 420 ⎯ SP 1.5 3 700 9 100 45DS704842C 1-P 0.4 1.68 2.5 217
355 ⎯ 490 ⎯ 316 ⎯ 316 ⎯ 2 1.6 3 540 7 920 47TS714932 1 0.33 2.03 3.02 169
355.600 14.0000 482.600 19.0000 269.875 10.6250 265.112 10.4375 3.2 1.5 2 680 6 090 47TS714827 1-P 0.47 1.43 2.12 134
360 ⎯ 480 ⎯ 375 ⎯ 375 ⎯ 3 1 4 120 10 600 47TS724838A 1 0.4 1.68 2.5 181
374.650 14.7500 501.650 19.7500 260.350 10.2500 250.825 9.8750 3.2 1.6 3 120 7 470 47TS755026A 2 0.33 2.03 3.02 136
380 ⎯ 580 ⎯ 370 ⎯ 370 ⎯ 3 SP 5 690 12 300 47TS765837 1-P 0.33 2.03 3.02 353
395 ⎯ 545 ⎯ 360 ⎯ 360 ⎯ 6 1.6 3 790 8 930 47TS795536A 1 0.47 1.43 2.12 242
406.400 16.0000 546.100 21.5000 288.925 11.3750 288.925 11.3750 6.4 1 3 620 8 190 47TS815529D-2 2-P 0.47 1.43 2.12 195
406.400 16.0000 546.100 21.5000 330.000 12.9921 330.000 12.9921 4 1.5 4 310 10 500 47TS815533A 2-P 0.43 1.57 2.34 204
406.400 16.0000 546.100 21.5000 357.400 14.0709 357.400 14.0709 3.2 1.6 3 960 9 540 47TS815536A 1 0.47 1.43 2.12 220
410 ⎯ 546 ⎯ 400 ⎯ 400 ⎯ 4 1.5 4 630 12 000 47TS825540 1 0.26 2.55 3.8 255
C 133 C 134
d 415.925 ∼ 482.600 mm
T
r
r1
uD ud
(kN)
d D T W r 1) r1 1)
(kg)
Cr C0r e Y2 Y3
mm 1/25.4 mm 1/25.4 mm 1/25.4 mm 1/25.4 min. min.
415.925 16.3750 590.550 23.2500 434.975 17.1250 434.975 17.1250 4 1.5 6 390 15 600 47TS835944A 2-P 0.4 1.68 2.5 377
420 ⎯ 560 ⎯ 437 ⎯ 437 ⎯ 4 3 5 620 14 900 47TS845644 1 0.26 2.55 3.8 298
420 ⎯ 574 ⎯ 480 ⎯ 480 ⎯ 3 1.6 6 730 17 800 47TS845748 1-P 0.28 2.43 3.61 352
420 ⎯ 620 ⎯ 395 ⎯ 320 ⎯ SP SP 5 160 11 600 47TS846240 1-P 0.47 1.43 2.12 390
430 ⎯ 575 ⎯ 380 ⎯ 380 ⎯ 3.2 SP 5 200 14 300 47TS865838A 2-P 0.26 2.55 3.8 276
431.800 17.0000 571.500 22.5000 336.550 13.2500 336.550 13.2500 3.2 1.5 4 440 11 600 47TS865734A 2 0.4 1.68 2.5 229
440 ⎯ 590 ⎯ 480 ⎯ 480 ⎯ 4 SP 6 870 18 700 47TS885948A-3 2-P 0.26 2.55 3.8 362
440 ⎯ 620 ⎯ 454 ⎯ 454 ⎯ 4 1.5 6 580 16 100 47TS886245-1 1-P 0.33 2.03 3.02 430
440 ⎯ 635 ⎯ 470 ⎯ 413 ⎯ 5 2 6 870 15 700 47TS886447 1 0.33 2.03 3.02 461
450 ⎯ 595 ⎯ 420 ⎯ 420 ⎯ 5 1.5 6 110 16 300 47TS906042 1-P 0.26 2.55 3.8 308
457.200 18.0000 596.900 23.5000 279.400 11.0000 276.225 10.8750 3.2 1.6 3 760 9 520 47TS916028C 2-P 0.47 1.43 2.12 191
457.200 18.0000 596.900 23.5000 279.400 11.0000 276.225 10.8750 3.2 1.6 3 300 8 180 47TS916028D 2-P 0.7 0.97 1.44 187
460 ⎯ 620 ⎯ 470 ⎯ 470 ⎯ 4 1.5 7 060 19 300 47TS926247 1-P 0.26 2.55 3.8 412
479.425 18.8750 679.450 26.7500 495.300 19.5000 495.300 19.5000 6.4 2 8 030 19 600 47TS966850 1-P 0.33 2.03 3.02 562
480.000 18.8976 647.700 25.5000 417.512 16.4375 417.512 16.4375 6.4 SP 6 680 17 400 47TS966542 1-P 0.33 2.03 3.02 391
480 ⎯ 700 ⎯ 470 ⎯ 470 ⎯ 5 1.5 8 080 18 800 47TS967047 1-P 0.32 2.12 3.15 621
482.600 19.0000 615.950 24.2500 330.200 13.0000 330.200 13.0000 6.4 1.6 4 310 11 700 4TRS19B 1-P 0.44 1.54 2.3 240
482.600 19.0000 615.950 24.2500 330.200 13.0000 330.200 13.0000 3.2 1.6 4 360 11 800 4TRS19C 2 0.4 1.68 2.5 229
482.600 19.0000 615.950 24.2500 330.200 13.0000 330.200 13.0000 3.2 1.6 4 510 12 400 4TRS19D 2-P 0.4 1.68 2.5 239
482.600 19.0000 615.950 24.2500 385.000 15.1575 385.000 15.1575 6.4 1.6 5 270 15 000 47TS976239 1-P 0.33 2.03 3.02 278
482.600 19.0000 615.950 24.2500 420.000 16.5354 420.000 16.5354 6.4 1.6 5 090 14 500 47TS976242 1 0.33 2.03 3.02 302
482.600 19.0000 615.950 24.2500 425.000 16.7323 425.000 16.7323 6.4 1.6 5 090 14 500 47TS976243 1 0.33 2.03 3.02 306
482.600 19.0000 647.700 25.5000 417.512 16.4375 417.512 16.4375 6.4 1.6 6 680 17 400 47TS976542A 1-P 0.33 2.03 3.02 382
C 135 C 136
d 488.950 ∼ 800 mm
T
r
r1
uD ud
(kN)
d D T W r 1) r1 1)
(kg)
Cr C0r e Y2 Y3
mm 1/25.4 mm 1/25.4 mm 1/25.4 mm 1/25.4 min. min.
488.950 19.2500 622.300 24.5000 365.125 14.3750 365.125 14.3750 6.4 1.5 4 320 12 200 47TS986236 1 0.4 1.68 2.5 270
492 ⎯ 655 ⎯ 480 ⎯ 480 ⎯ 5 1.5 7 450 21 200 47TS986648 1-P 0.33 2.03 3.02 449
509.948 20.0767 654.924 25.7844 379.000 14.9213 377.000 14.8425 6.4 1.5 5 370 15 200 4TRS510B 1-P 0.41 1.64 2.44 320
530 ⎯ 715 ⎯ 590 ⎯ 590 ⎯ 5 1.5 10 300 28 900 4TRS530A 1-P 0.26 2.55 3.8 664
558.800 22.0000 736.600 29.0000 372.263 14.6560 372.263 14.6560 7 SP 6 910 16 100 4TRS559J 1-P 0.34 1.97 2.93 425
558.800 22.0000 736.600 29.0000 409.575 16.1250 409.575 16.1250 6 1.5 6 850 18 600 4TRS559C 1-P 0.35 1.95 2.9 475
558.800 22.0000 736.600 29.0000 450.000 17.7165 450.000 17.7165 6 1.5 7 180 19 700 4TRS559A 1-P 0.35 1.95 2.9 507
558.800 22.0000 736.600 29.0000 480.000 18.8976 480.000 18.8976 6 1.5 7 960 22 700 4TRS559B 1-P 0.4 1.68 2.5 547
558.800 22.0000 736.600 29.0000 500.000 19.6850 500.000 19.6850 6 1.6 8 220 23 100 4TRS559 1-P 0.35 1.95 2.9 560
585.788 23.0625 771.525 30.3750 479.425 18.8750 479.425 18.8750 6.4 1.5 8 730 24 400 4TRS586A 1-P 0.33 2.03 3.02 613
595.312 23.4375 844.550 33.2500 615.950 24.2500 615.950 24.2500 6.4 3.6 12 700 32 200 4TRS595B 1-P 0.33 2.03 3.02 1 120
600 ⎯ 870 ⎯ 700 ⎯ 700 ⎯ 5 4 15 100 39 400 4TRS600A 1-P 0.33 2.03 3.02 1 370
609.600 24.0000 787.400 31.0000 361.950 14.2500 361.950 14.2500 6.4 3.2 5 920 14 900 4TRS610 1-P 0.4 1.68 2.5 430
609.600 24.0000 813.562 32.0300 540.000 21.2598 540.000 21.2598 6.4 1.5 10 200 28 500 4TRS610A 1-P 0.33 2.03 3.02 775
679.450 26.7500 901.700 35.5000 552.450 21.7500 552.450 21.7500 6.4 3 11 100 30 600 4TRS679 1-P 0.33 2.03 3.02 951
685.800 27.000 876.300 34.5000 355.600 14.0000 352.425 13.8750 6.4 3.2 6 130 16 300 4TRS686A 1-P 0.42 1.62 2.42 520
704.850 27.7500 914.400 36.0000 552.450 21.7500 552.450 21.7500 6.4 3.2 11 300 33 400 4TRS705 1-P 0.33 2.03 3.02 940
711.200 28.0000 914.400 36.0000 317.500 12.5000 317.500 12.5000 3.2 SP 6 070 16 700 4TRS711N 2-P 0.46 1.47 2.19 507
711.200 28.0000 914.400 36.0000 387.350 15.2500 387.350 15.2500 6.4 3.2 7 160 19 400 4TRS711A 1-P 0.38 1.78 2.65 615
711.200 28.0000 914.400 36.0000 410.000 16.1417 410.000 16.1417 6.4 3.2 7 610 20 500 4TRS711 1-P 0.44 1.54 2.29 670
711.200 28.0000 914.400 36.0000 420.000 16.5354 420.000 16.5354 6.4 3.2 7 870 22 200 4TRS711L 1-P 0.4 1.68 2.5 678
800 ⎯ 1 130 ⎯ 780 ⎯ 780 ⎯ 6 1.5 21 900 58 800 4TRS800 1-P 0.26 2.55 3.8 2 520
C 137 C 138
Bearings for railway rolling Cylindrical roller bearings
stock axle journals

Bearings used to support rolling stock axle journals are
required to be very strong and, at the same time, to be small Bore diameter 85 – 133 mm
because of limited space.
Sealed type cylindrical roller
Double-row bearings that are larger in width than general
bearing units
bearings are popular in that they are compact and have high
load ratings.
■ Cylindrical roller bearings

¡Feature good high-speed performance, and can be
maintained and inspected easily because of their
separable structure. Bore diameter 95 – 120 mm
Most commonly used bearing.
¡Those with a rib next to the inner ring are able to support Sealed type tapered roller bearing
not only radial load but also a certain degree of axial load, units(ABU)
so that a ball bearing is not required to accommodate the
axial load.
■ Sealed type cylindrical roller bearing units and tapered

roller bearing units
¡Maintenance-free : pre-lubricated with grease and Bore diameter 101.600 – 177.787 mm
provided with oil seals.
¡Can be used with a simplified axle box, or with an adapter
instead.
¡The inch series axle bearing units (ABU) are as specified
in the "association of american rail-roads".
C 139 C 140
Tolerances ¡Cylindrical roller and axial load support ball bearings Table 2 Metric series ABU bearing tolerances Unit : μm
: as specified in JIS B 1514-1, class 0 (Table 7-3 on pp. A 54 −A 57).
The tolerances for cylindrical roller bearing width and Single plane mean Single plane mean Single outer Actual overall
Nominal bore diameter outside diameter ring width width of inner
overall width are as shown in Table 1.
bore deviation deviation deviation rings deviation
¡Metric series ABU bearings: refer to Table 2. diameter 3 dmp 3 Dmp 3 Cs 3 B1s
¡Inch series ABU bearings : refer to Table 3. d (mm)
upper lower upper lower upper lower upper lower
Recommended fits Refer to Table 4.
110 0 − 20 + 50 − 50
Radial internal clearance ¡Cylindrical roller bearings : class C 3 120 0 − 20 0 − 125 + 100 − 100 + 500 − 500 C
UIC* standard cylindrical roller bearings : class C 4 130 0 − 25 + 100 − 100
(refer to Table 10-8 on p. A 100.)
¡Axial load support ball bearings : class C 5 B1
However, the clearance class should be adjusted according to the axle box
structure. Consult with JTEKT for further information. Table 3 Inch series ABU bearing tolerances Unit : μm uD ud
¡ABU bearings : class C 3 (refer to Table 10-10 on p. A 104)
*Denotes that the bearings are compatible with axle journals and axle boxes Single plane mean Single plane mean Single outer Actual overall
Nominal bore diameter outside diameter ring width width of inner
standardized by the UIC. bore deviation deviation deviation rings deviation
diameter 3 dmp 3 Dmp 3 Cs 3 B1s
d (mm)
upper lower upper lower upper lower upper lower
Table 1 Cylindrical roller bearings for axle journals : tolerances for
inner ring width, outer ring width and overall width C1 101.6to177.8 + 25 0 + 127 0 + 50 − 250 + 710 − 510
(1) Tolerances for inner ring width and inner ring overall width Unit : μm
Nominal bore B
diameter 3 Bs or 3 B1s 1-1 Table 4 Axle journal bearing recommended fits
Bearing type Design d (mm)
C1 Axle journal diameter (mm) Axle journal Axle box bore
over up to upper lower Bearing type
over up to tolerance class tolerance class
Inner ring one-piece
1-1, 1-2 80 120 0 − 400
type, Inner ring with 50 100 (m 6), n 6
2-1, 2-3 120 180 0 − 500 Cylindrical roller bearing
a rib and loose rib B 100 140 n6 H7
Tapered roller bearing
1-2
Two inner rings and 80 120 0 − 600 140 240 p6
2-2
spacer 120 180 0 − 700 Axial load support Clearance fit (clearance
C1 All diameters k5
deep groove ball bearing of approx. 0.2 to 0.6 mm)
(2) Tolerances for outer ring width and outer ring overall width Unit : μm
Nominal bore
B1
diameter 3 Cs or 3 C1s
Bearing type Design 2-1
d (mm)
C1
over up to upper lower
Outer ring 80 120 0 − 300

2-3
one-piece type 120 180 0 − 350 B1
2-2
Outer ring and 80 120 + 100 − 200
1-1
two loose ribs 120 180 + 100 − 250 C
Two outer rings 2-11) 120 180 0 − 500
Two outer rings and 1-2 80 120 0 − 500

spacer
B1
2-1, 2-2 120 180 0 − 600
2-3
[Note] 1) (2-1) means that spacer shown in Design 2-1 is removed.
C 141 C 142
Cylindrical roller bearings
for railway rolling stock axle journals
d 85 ∼ (120) mm d (120) ∼ 133 mm
C C C C C
r r r r r
B r1 r1 r1 r1 r1
B B B B
uD u d u Fw uD u d u Fw uD u d u Fw uD u d u Fw uD u d u Fw
Design 1 Design 2 Design 3 Design 4 Design 5
Basic load Basic load

Boundary dimensions (Refer.) Boundary dimensions (Refer.)
ratings ratings
(mm) (kN) Bearing No.2) Design3) Mass (mm) (kN) Bearing No.2) Design3) Mass
r r11) (kg) r r11) (kg)
d D B C Fw min. min.
Cr C0r d D B C Fw Cr C0r
min. min.
85 150 130 120 101.5 1.1 (7) 369 592 2U2217SC 3 8.6 120 240 185 180 150 2 (7) 983 1 600 2CR120A 1 37.8
90 160 88 80 107 2 2 355 529 2CR90D 1 7.2 130 220 170 160 152 1.1 0.6 865 1 520 4UJ130B 5 25.2
240 160 160 157 3 5 867 1 390 (2CR2624A) 2 32.0
95 170 120 105 114 1.1 (10) 497 804 2UJ95 4 10.9 240 180 160 158 1.1 (10) 970 1 610 4UJ130A 5 35.8
170 125 115 113.5 2.5 (7) 441 687 2CR95A 1 11.5
240 204 198 157 3 5 867 1 390 (2CR2624) 2 35.4
170 130 130 114 2 2 441 688 2UJ1917 3 11.4
250 160 160 158 3 7.5 1 090 1 720 (26NJ/NJP2580) 2 36.4
170 140 125 114 1.1 (10) 555 926 4UJ95 5 12.7 260 180 160 163 1.1 (10) 1 080 1 710 JC5 4 42.7
100 180 150 134 120 1.1 (10) 594 990 4UJ100 5 15.1 260 185 180 163 3 (7) 1 030 1 610 2CR130A 1 44.2
190 140 130 122 2.5 (7) 697 1 120 20DC19130/140 3 16.9 260 186 172 164 3 7.5 1 220 1 930 26NJ/NUJ2686 (2) 44.6
200 170 170 125 2 (7) 755 1 160 2CR100 1 23.7 260 205.5 180 163 3 (30) 1 030 1 610 JC21 (1) 45.1
200 170 170 125 2 (10) 755 1 160 20DC20170 3 23.2 270 215 210 164 4 (15) 1 280 2 000 JC29 3 55.1
280 215 210 167 4 (15) 1 440 2 250 JC9-1 3 61.4
110 200 180 160 134 1.1 (7) 721 1 190 JC3 5 22.6
220 180 160 138 2.5 (7) 789 1 190 JC6 1 30.0 133 280 215 210 167 4 (15) 1 440 2 250 JC9-2 3 59.8
220 185 180 138 2 (7) 922 1 460 2CR110 1 31.3 [Notes] 1) Values in ( ) indicate axial chamfer dimension.
2) Bearings indicated in ( ) are in accordance with UIC standards.
225 150 140 138 1.1 (7) 833 1 230 JC1A 4 27.7 3) (1) means that the inner ring (rib side) shown in Design 1 has a special form.
225 150 140 138 2.5 (7) 897 1 350 22DC23140/150 3 26.7 (2) means that loose rib shown in Design 2 is replaced with thrust collar.
235 180 160 141 2.5 (7) 934 1 430 JC2A 3 35.3
116 220 185 180 142 2 (7) 891 1 470 2CR116 1 30.5
225 150 140 197.5 1.1 (7) 786 1 220 2UJ116 4 26.0
120 225 170 165 145 3 (10) 876 1 380 JC35 1 29.4
230 170 165 145 3 (10) 943 1 460 JC34 1 30.8
230 177 150 145 3 (30) 943 1 460 JC27X (1) 29.7
240 160 160 150 3 7.5 961 1 500 (24NJ/NJP2480) 2 33.9
240 180 160 150 1.1 (10) 1 020 1 580 JC11 4 35.5
240 180 176 150 3 (7) 1 020 1 580 JC12 1 37.7
[Notes] 1) Values in ( ) indicate axial chamfer dimension.
2) Bearings indicated in ( ) are in accordance with UIC standards.
3) (1) means that the inner ring (rib side) shown in Design 1 has a special form.
(2) means that loose rib shown in Design 2 is replaced with thrust collar.
C 143 C 144
Sealed type cylindrical roller bearings for railway rolling stock axle journals
d 95 ∼ 120 mm
S R Q S R Q S R Q S R Q S R Q S R Q
B3 E B3 E B3 E B3 E B3 E B3 E
C C C C C C
uM ud uD u d3 ud uD u d3 uM ud uD u d3 uM ud uD u d3 uPuMud uD u d3 uM ud uD u d3
K F G H F G H K F G H K F G H L K F G H K F G H
Design 1 Design 2 Design 3 Design 4 Design 5 Design 6
Shaft S R Q
Boundary dimensions Basic load ratings (Refer.)
dia. Unit B3 E
Unit No. Design Bearing No.
(mm) (mm) (kN) Mass C
d
d Brg.
D C B3 d3 E F G H K L M P Q R S Cr C0r (kg)
95 JB1425 1 95 190 140 158 120 25 62 90 35 48 ⎯ M85×4 ⎯ 18 107 119 19RDC19140/158 610 910 24.5
100 JB1199B 2 100 195 150 175 130 30 120 105 42 ⎯ ⎯ ⎯ ⎯ 24 123 130 20RDC20150/133B 673 1 040 27.5 u Pu M u d uD u d3
L K F G H
110 JB1462 3 110 220 145 171 155 39 70 110 50 42 ⎯ M100×2 ⎯ 33 127 134 S-JC33 789 1 190 35.9
120 JB1356 4 120 220 150 170 158 46 70 116 36 51 ⎯ M115×4 ⎯ 19 133 131 24RDC22150/170 702 1 110 34.9
JB1380D 5 120 230 150 171 155 43 70 113 42 42 33 M110×2 85 25 130 152 JC32 831 1 290 39.0 Design 7
JB1010 6 120 240 170 218 168 35 87 125 45 43 ⎯ M110×2 ⎯ 25 145 164 JC17 1 020 1 580 57.7
S R
B3 E
JB1240 7 120 240 160 193 168 31 80 113 38 40 38 M110×2 85 27 128 169 JC26 935 1 420 51.1
C
JB1377 8 120 240 160 192 150 30 83 112 40 38 ⎯ M110×4 ⎯ ⎯ 135 131 24RDC24160/192A 935 1 420 42.0
uM ud uD u d3
K F G H
Design 8
C 145 C 146
Sealed type tapered roller bearings for railway rolling stock axle journals
(ABU bearing) K
d 101.6 ∼ 177.787 mm S R Q S R Q
110 ∼ 130 mm Q
C C
L S R Q
M J Dynamic equivalent load
(when Fa/Fr =< e)
ud uD u d1 ud uD u d1 P=Fr + Y2 Fa
N F G F G (when Fa/Fr > e)
B1 H B1 H P=0.67Fr + Y3 Fa
ud uD u d1 Static equivalent load
F
E
G P0=Fr + Y0 Fa
H
B1
The shape of the backing ring
used for JB1204P, JB1205P and
C JB1206P. JB1486 JB1450
Dimen- Basic load Con- Axial load

Boundary dimensions Dimensions of adapter (Refer.)
Axle Unit Bolt sions ratings stant factors
Class Adapter Mass
size No. (mm) (mm) size (mm) Bearing No. (kN)
No. (kg)
d
Brg. Axle1)
D B1 C d11) E F G H Q R S J K L M N p Cr C0r e Y2 Y3 Y0 Unit Adapter
101.702 3/4-10 HM120848/
B 4 /4×8
1
JB1201 101.600 101.676 165.100 106.362 114.300 127.0 182.6 101.6 117.5 41.3 41.3 117.5 134.8 JB701 117.5 68.3 165.9 124.6 101.6 UNC 61.9 HM120817XD 402 769 0.26 2.55 3.80 2.50 17.3 3.8
119.164 7/8-9 HM124646/
C 5 ×9 JB1202 119.062 119.139 195.262 136.525 142.875 149.2 217.5 112.7 134.9 36.5 36.5 134.9 147.0 JB702 146.0 74.6 196.1 143.7 117.5 UNC 76.2 HM124618XD 626 1 200 0.26 2.55 3.80 2.50 25.3 6.1
131.864 7/8-9 HM127446/
D 5 1/2×10 JB1203 131.750 131.839 207.962 146.050 152.400 161.9 227.0 115.9 139.7 44.5 44.5 139.7 150.5 JB703 155.6 74.6 208.8 156.4 123.8 UNC 88.9 HM127415XD 641 1 270 0.26 2.55 3.80 2.50 28.3 7.4
144.564 1-8 HM129848/
JB1204 144.450 144.539 220.662 155.575 163.512 177.8 241.3 127.0 150.8 46.0 46.0 150.8 164.1 JB704 166.7 96.8 221.5 181.8 136.5 UNC 98.4 HM129814XD 667 1 380 0.26 2.55 3.80 2.50 34.3 10.8
E 6 ×11
144.564 178.613 1-8 HM129848/
JB1204P 144.450 144.539 220.662 155.575 163.512 178.562 241.3 127.0 150.8 46.0 36.8 160.0 164.1 JB704 166.7 96.8 221.5 181.8 136.5 UNC 98.4 HM129814XD 667 1 380 0.26 2.55 3.80 2.50 35.0 10.8
157.264 1 1/8 -7 HM133444/
JB1205 157.150 157.239 252.412 177.800 184.150 190.5 273.0 134.9 163.5 46.0 46.0 163.5 176.6 JB705 187.3 96.8 253.2 194.5 152.4 UNC 108.0 HM133416XD 910 1 890 0.26 2.55 3.80 2.50 51.6 16.3
F 6 1/2×12 1
157.264 191.313 1 /8 -7 HM133444/
JB1205P 157.150 157.239 252.412 177.800 184.150 191.262 273.0 134.9 163.5 46.0 36.7 172.8 176.6 JB705 187.3 96.8 253.2 194.5 152.4 UNC 108.0 HM133416XD 910 1 890 0.26 2.55 3.80 2.50 52.4 16.3
177.902 203.251 ⎯ 1 1/4 -7 HM136948/
G 7 ×12 JB1206P 177.787 177.876 276.225 180.975 185.738 203.200 269.9 130.2 150.8 58.7 46.0 163.5 180.1 JB7062) 189.7 181.0 279.4 168.3 UNC 117.5 HM136916XD 1 080 2 220 0.26 2.55 3.80 2.50 59.2 23
⎯ 110.076
JB558 110 110.054 175 125 130 155 206 105 135 30 30 135 136.4 JB558 134 70 175 135 110 M22 75 JT9 481 972 0.26 2.55 3.80 2.50 22.0 5.6
110
⎯ 110.059 150.068 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯
JB1486 110 110.037 205 130 140 150.043 85 105 53 43 115 118.4 M22 75 JT13 743 1 220 0.26 2.55 3.80 2.50 27.3
⎯ 120.076
JB613 120 120.054 195 136 142 155 217 113 135 30 30 135 147.5 JB613 146 74.5 196 142.5 118 M22 75 JT10 626 1 200 0.26 2.55 3.80 2.50 27.0 6.2
120
⎯ 120.059 150.068 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯
JB1450 120 120.037 220 155 155 150.043 125 100 55 35 120 164.4 M22 75 JT12 907 1 670 0.26 2.55 3.80 2.50 36.6
⎯ 130.076
130 JB633 130 130.054 208 146 152 165 227 139 139 26 26 139 149.2 JB6332) 156 110 255 232 130 M22 89 JT11 641 1 270 0.26 2.55 3.80 2.50 30.0 14.3
[Notes] 1) Upper figures : max. value ; lower : min.value 2) JB706 and JB633 indicate the specifications of wide adapters.
Others indicate narrow adapters (shown in figures above).
C 147 C 148
Linear ball bearings
Ball complement
bore diameter (mm)
Linear ball bearings have an outer cylinder and a SDM series ........................ 6 −120
cage with three or more elliptic raceways inside. SDMF, SDMK series ............ 6 − 80
Balls are aligned on these raceways. SDE series ........................ 5 − 80
Standard type Clearance adjustable type Open type
Suitable for a wide range of applications The outer cylinder and side plate are slit The outer cylinder and side plate each
and widely used in practice. axially so that the clearance between the have a slit which is equivalent in size
The upper-class type is used for general bearing and shaft can be adjusted. to a recirculating ball row raceway, so
purposes. The precision-class type is Together with the use of a boreadjustable that the bearing does not interfere
used when the bearing is required to be housing, a no-clearance state or light- with a shaft strut during operation.
highly accurate. preloaded state can be realized without This type is suitable for use with very long
fitting. shafts. The bore diameter is adjustable.
Flanged type Bearing numbering system

SDM 35 UU AJ
Series Ball complement Seal Shape Material Tolerance

code bore diameter code code code code
number
SDM : metric series

SDMF : metric series (flanged type)
Series code SDMK : metric series (flanged type)
SDE : metric series (popular ones in europe)
SDB : inch series
Ball comple- Metric series 35 : ball complement bore diameter 35 mm

ment bore
diameter
Can be fit quickly, and number Inch series 4 : ball complement bore diameter 4/16 = 1/4 inch
helps make equipment
smaller and lighter in UU : both sides sealed
weight. Helps reduce cost. Seal code U : single side sealed
Not specified : not sealed
Sealed type
Not specified : standard type
Shape code AJ : clearance adjustable type
OP : open type
Outer cylinder
Material and balls Not specified : high carbon chrome bearing steel
code Not specified : cold rolled steel sheet
Cage
MG : synthetic resin
One or both side(s) is/are
sealed with special synthetic Not specified : upper-class
rubber so that foreign material Tolerance code P : precision-class
cannot enter the bearing while
the grease is kept from leaking.
This sealing can be provided on
all bearings of the standard,
clearance adjustable, open,
and flanged types.
C 149 C 150
■ Linear ball bearing service life ¡Ball row arrangement and load rating ■ Recommended fits for linear ball bearings
Linear ball bearing service life refers to the The basic load ratings given in the Table 3 lists the recommended fits for linear For the clearance adjustable and open type
distance that the bearing travels until the outer specification table are those measured when a ball bearings. bearings, it is best for the shaft diameter to be
cylinder, balls or shaft become damaged because load is applied directly above a ball row (Q1). When a bearing is mounted with a housing, the smaller than the ball complement bore diameter
of rolling contact fatigue from repeated stress. When the load is applied between two ball rows, normal clearance fit should be selected. When lower deviation, and for the housing bore
The basic dynamic load rating refers to the the load ratings become larger (Q2). Table 2 lists the application is highly precise or special, the diameter to be larger than the bearing outside
magnitude of a constant load which makes a the ratios of Q2 ratings to Q1 ratings. transition fit should be selected. diameter upper deviation.
bearing's service life end after it travels a distance
of 50 km. Ball row arrangement and Table 3 Linear ball bearing recommended fits
Table 2
The linear ball bearing service life and the the comparison of load ratings
basic dynamic load rating bear the relation shown Shaft tolerance class Housing bore tolerance class
Number When a load is When a load is Ratios Bearing Tolerance
below : of ball applied directly applied between of Q2 Normal clearance Close clearance Clearance fit Transition fit
rows above a row (Q1) two rows (Q2) to Q1 Upper-class f 6, g 6 h6 H7 JS 7 (J 7)
3 SDM, SDB
C Precision-class f 5, g 5 h5 H6 JS 6 (J 6)
L = 50
P ( ) SDE − h6 js 6 (j 6) H7 JS 7 (J 7)
where : 4 1.414
L : service life km ■ Linear ball bearing clearance
P : radial load on the bearing N
C : bearing basic dynamic load rating N Linear ball bearings provide linear motion zero or negative, by adjusting one of the three
45° smoothly with little wear when the clearance is ball rows with a bolt.
(refer to the specification table.)
0.003 to 0.012 mm. However, when clearance Consult with JTEKT on the gauging of linear
Shaft surface hardness increase due to wear is considered critical, e.g. ball bearings and shafts which should be
is closely related to running when the bearing is provided to press die sets, mounted by "selective fitting," as well as on the
Hardness 5 1.463
performance. In general, it Table 1 coefficients precision machine tools or precision testers; whole design of shafts.
is best for the hardness to when the bearing becomes unable to slide
be 60 thru 64 HRC. Shaft Hardness because of moment; or when smooth bearing
hardness coefficient 36° operation is needed with no clearance provided,
If the hardness is 60
HRC fH the clearance is adjusted to zero or negative.
HRC or lower, the basic
dynamic load rating (C) 60 1 In such a case, shafts generally need to be
should be corrected by mounted by "selective fitting."
59 0.97
multiplying it by the appro- 6 1.280 They should be handled carefully so as not to
57 0.88 be preloaded excessively.
priate hardness coefficient
selected from Table 1. 55 0.76 As Fig. 1 shows, the clearance of bearings with
53 0.64 30°
numbers SDM 6 thru SDM 10 can be easily set to
51 0.52 [Note] When there are only three rows, Q2 / Q1 = 1 Fig. 1 Clearance adjustment
Table 4 SDM series linear ball bearing tolerances Unit : μm Table 5 SDE series linear ball bearing tolerances Unit : μm
Ball complement bore
Outside Eccentricity Ball complement Outside
diameter (Fw) deviation Overall length Overall length
Bearing number diameter B deviation Bearing number bore diameter (Fw) diameter (D) B deviation Eccentricity
Precision- Upper- (L) deviation Precision- Upper- (L) deviation
SDM (D) deviation SDE deviation deviation
class class class class
upper lower upper lower upper lower upper lower upper lower max. upper lower upper lower upper lower upper lower max.
6, 8 0 − 6 0 − 9 0 − 11 0 − 200 0 − 200 8 12 5, 8 + 8 0 0 − 8 0 − 200 0 − 200 12
10, 12, 13, 16 0 − 6 0 − 9 0 − 13 0 − 200 0 − 200 8 12 10, 12 + 8 0 0 − 9 0 − 200 0 − 200 12
20 0 − 7 0 − 10 0 − 16 0 − 200 0 − 200 10 15 16 + 9 −1 0 − 9 0 − 200 0 − 200 12
25, 30 0 − 7 0 − 10 0 − 16 0 − 300 0 − 300 10 15 20 + 9 −1 0 − 11 0 − 200 0 − 200 15
35, 38, 40, 50 0 − 8 0 − 12 0 − 19 0 − 300 0 − 300 12 20 25, 30 + 11 −1 0 − 11 0 − 300 0 − 300 15
60 0 − 9 0 − 15 0 − 22 0 − 300 0 − 300 17 25 40, 50 + 13 −2 0 − 13 0 − 300 0 − 300 17
80 0 − 9 0 − 15 0 − 22 0 − 400 0 − 400 17 25 60 + 13 −2 0 − 15 0 − 400 0 − 400 20
100, 120 0 − 10 0 − 20 0 − 25 0 − 400 0 − 400 20 30 80 + 16 −4 0 − 15 0 − 400 0 − 400 20
C 151 C 152
d 5 ∼ (20) mm
L
B
W W
h θ
h1
u D u D1 ud FW FW FW
Clearance
SDM, SDE Standard type adjustable type Open type SDM...MD
(...AJ) (...OP)
Shaft dia. Dimensions Bearing No.1) No. of ball rows Basic load ratings (Refer.)
(mm) (mm) (N) Mass
Standard Clearance Open Standard Clearanece Open (g)
d Fw D L B W D1 h h1 θ type adjustable type Cr C0r Standard type
type adjustable type type type
5 5 12 22 14.5 1.1 11.5 ⎯ ⎯ ⎯ SDE5 ⎯ ⎯ 3 ⎯ ⎯ 108 183 10
6 6 12 19 13.5 1.1 11.5 1 ⎯ ⎯ SDM6 SDM6AJ ⎯ 3 3 ⎯ 108 186 7

6 12 19 13.5 1.1 11.5 1 ⎯ ⎯ SDM6MG SDM6AJMG ⎯ 4 4 ⎯ 108 186 6
8 8 15 17 11.5 1.1 14.3 1 ⎯ ⎯ SDM8S SDM8SAJ ⎯ 3 3 ⎯ 96 160 10

8 15 17 11.5 1.1 14.3 1 ⎯ ⎯ SDM8SMG SDM8SAJMG ⎯ 4 4 ⎯ 96 160 9
8 15 24 17.5 1.1 14.3 1 ⎯ ⎯ SDM8 SDM8AJ ⎯ 3 3 ⎯ 122 223 14
8 15 24 17.5 1.1 14.3 1 ⎯ ⎯ SDM8MG SDM8AJMG ⎯ 4 4 ⎯ 134 255 13
8 16 25 16.5 1.1 15.2 1 ⎯ ⎯ SDE8 SDE8AJ ⎯ 3 3 ⎯ 122 223 20
8 16 25 16.5 1.1 15.2 1 ⎯ ⎯ SDE8MG SDE8AJMG ⎯ 4 4 ⎯ 134 255 18
10 10 19 29 22 1.3 18 1 6.8 80° SDM10 SDM10AJ SDM10OP 4 4 3 259 424 27

10 19 29 22 1.3 18 1 ⎯ ⎯ SDM10MG SDM8AJMG ⎯ 4 4 ⎯ 259 424 23
10 19 29 22 1.3 18 1 6.8 80° SDE10 SDE10AJ SDE10OP 4 4 3 259 424 27
10 19 29 22 1.3 18 1 ⎯ ⎯ SDE10MG SDE10AJMG ⎯ 4 4 ⎯ 259 424 23
12 12 21 30 23 1.3 20 1.5 8 80° SDM12 SDM12AJ SDM12OP 4 4 3 260 431 31

12 21 30 23 1.3 20 1.5 ⎯ ⎯ SDM12MG SDM12AJMG ⎯ 4 4 ⎯ 260 431 27
12 22 32 22.9 1.3 21 1.5 7.5 78° SDE12 SDE12AJ SDE12OP 4 4 3 289 503 42
12 22 32 22.9 1.3 21 1.5 ⎯ ⎯ SDE12MG SDM12AJMG ⎯ 4 4 ⎯ 289 503 37
13 13 23 32 23 1.3 22 1.5 9 80° SDM13 SDM13AJ SDM13OP 4 4 3 289 506 41

13 23 32 23 1.3 22 1.5 ⎯ ⎯ SDM13MG SDM13AJMG ⎯ 4 4 ⎯ 289 506 35
16 16 26 36 24.9 1.3 24.9 1.5 10 78° SDE16 SDE16AJ SDE16OP 4 4 3 319 587 53
16 26 36 24.9 1.3 24.9 1.5 ⎯ ⎯ SDE16MG SDE16AJMG ⎯ 4 4 ⎯ 319 587 47
16 28 37 26.5 1.6 27 1.5 11 80° SDM16 SDM16AJ SDM16OP 4 4 3 480 766 69
16 28 37 26.5 1.6 27 1.5 ⎯ ⎯ SDM16MG SDM16AJMG ⎯ 4 4 ⎯ 480 766 59
20 20 32 42 30.5 1.6 30.5 1.5 11 60° SDM20 SDM20AJ SDM20OP 5 5 4 590 1 010 92
20 32 42 30.5 1.6 30.5 1.5 ⎯ ⎯ SDM20MG SDM20AJMG ⎯ 5 5 ⎯ 590 1 010 79
[Note] 1) JTEKT also manufactures sealed types, which are identified by U (one side sealed) or UU (both sides sealed)
after ball complement bore diameter number.
C 153 C 154
d (20) ∼ 80 mm
L
B
W W
h θ
h1
Clearance
(...AJ) (...OP)
(mm) (mm) (N) Mass
20 20 32 45 31.5 1.6 30.3 2 10 60° SDE20 SDE20AJ SDE20OP 5 5 4 590 1 010 96

20 32 45 31.5 1.6 30.3 2 ⎯ ⎯ SDE20MG SDE20AJMG ⎯ 5 5 ⎯ 590 1 010 88
25 25 40 58 44.1 1.85 37.5 2 12.5 60° SDE25 SDE25AJ SDE25OP 5 5 4 1 130 2 030 190
25 40 58 44.1 1.85 37.5 2 ⎯ ⎯ SDE25MG SDE25AJMG ⎯ 5 5 ⎯ 1 130 2 030 170
25 40 59 41 1.85 38 2 12 60° SDM25 SDM25AJ SDM25OP 5 5 4 1 130 2 030 200
25 40 59 41 1.85 38 2 ⎯ ⎯ SDM25MG SDM25AJMG ⎯ 5 5 ⎯ 1 130 2 030 170
30 30 45 64 44.5 1.85 43 2.5 15 50° SDM30 SDM30AJ SDM30OP 6 6 5 1 470 2 770 250
30 45 64 44.5 1.85 43 2.5 ⎯ ⎯ SDM30MG SDM30AJMG ⎯ 6 6 ⎯ 1 470 2 770 220
30 47 68 52.1 1.85 44.5 2 12.5 50° SDE30 SDE30AJ SDE30OP 6 6 5 1 470 2 770 340
30 47 68 52.1 1.85 44.5 2 ⎯ ⎯ SDE30MG SDE30AJMG ⎯ 6 6 ⎯ 1 470 2 770 320
35 35 52 70 49.5 2.1 49 2.5 17 50° SDM35 SDM35AJ SDM35OP 6 6 5 1 580 3 070 370
35 52 70 49.5 2.1 49 2.5 ⎯ ⎯ SDM35MG SDM35AJMG ⎯ 6 6 ⎯ 1 580 3 070 330
38 38 57 76 58.5 2.1 54.5 3 18 50° SDM38 SDM38AJ SDM38OP 6 6 5 2 020 3 600 490
40 40 60 80 60.5 2.1 57 3 20 50° SDM40 SDM40AJ SDM40OP 6 6 5 2 180 4 010 590

40 60 80 60.5 2.1 57 3 ⎯ ⎯ SDM40MG SDM40AJMG ⎯ 6 6 ⎯ 2 180 4 010 530
40 62 80 60.6 2.15 59 3 16.8 50° SDE40 SDE40AJ SDE40OP 6 6 5 2 180 4 010 710
40 62 80 60.6 2.15 59 3 ⎯ ⎯ SDE40MG SDE40AJMG ⎯ 6 6 ⎯ 2 180 4 010 650
50 50 75 100 77.6 2.65 72 3 21 50° SDE50 SDE50AJ SDE50OP 6 6 5 4 020 7 110 1 050
50 80 100 74 2.6 76.5 3 25 50° SDM50 SDM50AJ SDM50OP 6 6 5 4 420 7 150 1 500
60 60 90 110 85 3.15 86.5 3 30 50° SDM60 SDM60AJ SDM60OP 6 6 5 5 170 9 030 1 850
60 90 125 101.7 3.15 86.5 3 27.2 54° SDE60 SDE60AJ SDE60OP 6 6 5 6 470 11 100 1 900
80 80 120 140 105.5 4.15 116 3 40 50° SDM80 SDM80AJ SDM80OP 6 6 5 8 180 12 800 4 200
80 120 165 133.7 4.15 116 3 36.3 54° SDE80 SDE80AJ SDE80OP 6 6 5 8 890 14 500 4 800
C 155 C 156
d 100 ∼ 120 mm
L
B
W W
h θ
h1
Clearance
(...AJ) (...OP)
(mm) (mm) (N) Mass
100 100 150 175 125.5 4.15 145 3 50 50° SDM100 SDM100AJ SDM100OP 6 6 5 12 300 19 700 8 200
120 120 180 200 158.6 4.15 175 4 85 80° SDM120 SDM120AJ SDM120OP 8 8 6 22 300 39 100 15 500
C 157 C 158
flanged type
d 6 ∼ 50 mm
L Mounting bolt
t
FW FW
uDud u P u Df
K
SDMF...MG
SDMF, SDMK Round-flanged Square-flanged (Synthetic resin) Round-flanged Square-flanged
SDMK...MG
Shaft dia. Dimensions Bearing No. Basic load ratings (Refer.)
(mm) (mm) Bolt No. of (N) Mass

size Round-flanged Square-flanged ball rows (g)
d Fw D L Df K t P Cr C0r Round-flanged type
type type
6 6 12 19 28 22 5 20 M3 SDMF6 SDMK6 3 108 186 23

6 12 19 28 22 5 20 M3 SDMF6MG SDMK6MG 4 108 186 22
8 8 15 24 32 25 5 24 M3 SDMF8 SDMK8 3 122 223 35

8 15 24 32 25 5 24 M3 SDMF8MG SDMK8MG 4 134 255 34
10 10 19 29 40 30 6 29 M4 SDMF10 SDMK10 4 259 424 65

10 19 29 40 30 6 29 M4 SDMF10MG SDMK10MG 4 259 424 61
12 12 21 30 42 32 6 32 M4 SDMF12 SDMK12 4 260 431 72

12 21 30 42 32 6 32 M4 SDMF12MG SDMK12MG 4 260 431 68
13 13 23 32 43 34 6 33 M4 SDMF13 SDMK13 4 289 506 83

13 23 32 43 34 6 33 M4 SDMF13MG SDMK13MG 4 289 506 77
16 16 28 37 48 37 6 38 M4 SDMF16 SDMK16 4 480 766 120

16 28 37 48 37 6 38 M4 SDMF16MG SDMK16MG 4 480 766 110
20 20 32 42 54 42 8 43 M5 SDMF20 SDMK20 5 590 1 010 170

20 32 42 54 42 8 43 M5 SDMF20MG SDMK20MG 5 590 1 010 160
25 25 40 59 62 50 8 51 M5 SDMF25 SDMK25 5 1 130 2 030 290

25 40 59 62 50 8 51 M5 SDMF25MG SDMK25MG 5 1 130 2 030 270
30 30 45 64 74 58 10 60 M6 SDMF30 SDMK30 6 1 470 2 770 440

30 45 64 74 58 10 60 M6 SDMF30MG SDMK30MG 6 1 470 2 770 410
35 35 52 70 82 64 10 67 M6 SDMF35 SDMK35 6 1 580 3 070 610

35 52 70 82 64 10 67 M6 SDMF35MG SDMK35MG 6 1 580 3 070 560
40 40 60 80 96 75 13 78 M8 SDMF40 SDMK40 6 2 180 4 010 1 000

40 60 80 96 75 13 78 M8 SDMF40MG SDMK40MG 6 2 180 4 010 930
50 50 80 100 116 92 13 98 M8 SDMF50 SDMK50 6 4 420 7 150 2 000
C 159 C 160
flanged type
d 60 ∼ 80 mm
L Mounting bolt
t
FW FW
uDud u P u Df
K
SDMF...MG
SDMF, SDMK Round-flanged Square-flanged (Synthetic resin) Round-flanged Square-flanged
SDMK...MG
Shaft dia. Dimensions Bearing No. Basic load ratings (Refer.)
(mm) (mm) Bolt No. of (N) Mass

size Round-flanged Square-flanged ball rows (g)
d Fw D L Df K t P Cr C0r Round-flanged type
type type
60 60 90 110 134 106 18 112 M10 SDMF60 SDMK60 6 5 170 9 030 2 800
80 80 120 140 164 136 18 142 M10 SDMF80 SDMK80 6 8 180 12 800 5 400
C 161 C 162
Locknuts, lockwashers & lock plates Locknuts
Bearings are often fit to a shaft with an adapter sleeve,

locknut, lockwasher or lock plate.
These accessories make it easy to attach and remove AN (ANL) 02 – 100
bearings. HN (HNL) 41 – 110
They are standardized in JIS.
Lockwashers and lock plates
¡Locknuts are standardized such that they can be used with
either adapter sleeves, withdrawal sleeves or shafts.
¡Lockwashers and lock plates are used as locks on locknuts.
Lockwashers are used with bearings of bore diameter AW (AWL) 00 – 40(X)

number 40 or lower. Lock plates are used with those of bore AL (ALL) 44 – 100
diameter 44 or higher.
C 163 C 164
Locknuts
for adapter sleeves and shafts AN 26 ∼ 40
AN02 ∼ 25 ANL24 ∼ 40
g B
b
h 30°
r1
G
d2
u d6 u d1
Standard dimensions (Refer.) Applicable2) Applicable3) Standard dimensions Applicable2) Applicable3)

Locknut Thread size1) Locknut Thread size1) (Refer.)
(mm) Mass adapter lockwasher (mm) Mass adapter lockwasher
No. r1 No.
(kg) sleeve No. r1 (kg) sleeve No.
G d2 d1 g d6 b h B max. G d2 d1 g d6 b h B
(bore No.) max. (bore No.)
AN 02 M 15×1 25 21 21 15.5 4 2 5 0.4 0.010 ⎯ AW 02 AN 26 M130×2 165 149 155 131 12 5 21 0.7 1.25 26 AW 26
03 M 17×1 28 24 24 17.5 4 2 5 0.4 0.013 ⎯ 03
04 M 20×1 32 26 28 20.5 4 2 6 0.4 0.019 04 04 AN 27 M135×2 175 160 163 136 14 6 22 0.7 1.55 ⎯ AW 27
28 M140×2 180 160 168 141 14 6 22 0.7 1.56 28 28
AN 05 M 25×1.5 38 32 34 25.8 5 2 7 0.4 0.025 05 AW 05
06 M 30×1.5 45 38 41 30.8 5 2 7 0.4 0.043 06 06 AN 29 M145×2 190 172 178 146 14 6 24 0.7 1.80 ⎯ AW 29
07 M 35×1.5 52 44 48 35.8 5 2 8 0.4 0.053 07 07 30 M150×2 195 171 183 151 14 6 24 0.7 2.03 30 30
31 M155×3 200 182 186 156.5 16 7 25 0.7 2.30 ⎯ ⎯
AN 08 M 40×1.5 58 50 53 40.8 6 2.5 9 0.5 0.085 08 AW 08
09 M 45×1.5 65 56 60 45.8 6 2.5 10 0.5 0.119 09 09 AN 32 M160×3 210 182 196 161.5 16 7 25 0.7 2.59 32 AW 32
10 M 50×1.5 70 61 65 50.8 6 2.5 11 0.5 0.148 10 10 33 M165×3 210 193 196 166.5 16 7 26 0.7 2.70 ⎯ ⎯
34 M170×3 220 193 206 171.5 16 7 26 0.7 2.80 34 34
AN 11 M 55×2 75 67 69 56 7 3 11 0.5 0.158 11 AW 11
12 M 60×2 80 73 74 61 7 3 11 0.5 0.174 12 12 AN 36 M180×3 230 203 214 181.5 18 8 27 0.7 3.07 36 AW 36
13 M 65×2 85 79 79 66 7 3 12 0.5 0.203 13 13 38 M190×3 240 214 224 191.5 18 8 28 0.7 3.39 38 38
40 M200×3 250 226 234 201.5 18 8 29 0.7 3.69 40 40
AN 14 M 70×2 92 85 85 71 8 3.5 12 0.5 0.242 14 AW 14
15 M 75×2 98 90 91 76 8 3.5 13 0.5 0.287 15 15
16 M 80×2 105 95 98 81 8 3.5 15 0.6 0.397 16 16 ANL24 M120×2 145 133 135 121 12 5 20 0.7 0.78 24 AWL24
26 M130×2 155 143 145 131 12 5 21 0.7 0.88 26 26
AN 17 M 85×2 110 102 103 86 8 3.5 16 0.6 0.451 17 AW 17 28 M140×2 165 151 153 141 14 6 22 0.7 0.99 28 28
18 M 90×2 120 108 112 91 10 4 16 0.6 0.556 18 18
19 M 95×2 125 113 117 96 10 4 17 0.6 0.658 19 19 ANL30 M150×2 180 164 168 151 14 6 24 0.7 1.33 30 AWL30
32 M160×3 190 174 176 161.5 16 7 25 0.7 1.56 32 32
AN 20 M100×2 130 120 122 101 10 4 18 0.6 0.698 20 AW 20 34 M170×3 200 184 186 171.5 16 7 26 0.7 1.72 34 34
21 M105×2 140 126 130 106 12 5 18 0.7 0.845 21 21
22 M110×2 145 133 135 111 12 5 19 0.7 0.965 22 22 ANL36 M180×3 210 192 194 181.5 18 8 27 0.7 1.95 36 AWL36
38 M190×3 220 202 204 191.5 18 8 28 0.7 2.08 38 38
AN 23 M115×2 150 137 140 116 12 5 19 0.7 1.01 ⎯ AW 23 40 M200×3 240 218 224 201.5 18 8 29 0.7 2.98 40 40
24 M120×2 155 138 145 121 12 5 20 0.7 1.08 24 24 [Notes] 1) Basic profile and dimension of screw thread are in accordance with JIS B 0205.
25 M125×2 160 148 150 126 12 5 21 0.7 1.19 ⎯ 25 2) Applicable to adapter sleeve series A31, A2, A3 and A23.
3) Applicable to lockwashers with flat inner tongue.
[Notes] 1) Basic profile and dimension of screw thread are in accordance with JIS B 0205. [Remark] Locknut series AN is used for adapter assembly series H2, H3, H23 and H31, while locknut series ANL is used
2) Applicable to adapter sleeve series A31, A2, A3 and A23. for adapter assembly series H30.
3) Applicable to lockwashers with flat inner tongue.
[Remark] Locknut series AN is used for adapter assembly series H2, H3, H23 and H31, while locknut series ANL is used
for adapter assembly series H30.
C 165 C 166
Locknuts
for adapter sleeves and shafts ANL 80 ∼ 100
AN 44 ∼ 100
ANL 44 ∼ 76 B g
l b
30° h
S
r1
G
d2
u d 1 u d6 u dp
Locknut Thread1) Standard dimensions Tapped hole2) (Refer.) Applicable Applicable Locknut Thread1) Standard dimensions Tapped hole2) (Refer.) Applicable Applicable
No. size (mm) (mm) Mass adapter lock plate No. size (mm) (mm) Mass adapter lock plate
r1 S sleeve3) No. r1 S sleeve3) No.
G d2 d1 g d6 b h B l dp (kg) G d2 d1 g d6 b h B l dp (kg)
max. Thread size (bore No.) max. Thread size (bore No.)
AN 44 Tr220×4 280 250 260 222 20 10 32 0.8 15 M 8×1.25 238 5.16 44 AL 44 ANL80 Tr400×5 470 442 442 402.5 28 14 52 1 18 M10×1.5 418 16.9 80 ALL76
48 Tr240×4 300 270 280 242 20 10 34 0.8 15 M 8×1.25 258 5.91 48 44 84 Tr420×5 490 462 462 422.5 32 14 52 1 18 M10×1.5 438 17.4 84 84
52 Tr260×4 330 300 306 262 24 12 36 0.8 18 M10×1.5 281 7.99 52 52 88 Tr440×5 520 490 490 442.5 32 15 60 1 21 M12×1.75 462 26.2 88 88
AN 56 Tr280×4 350 320 326 282 24 12 38 0.8 18 M10×1.5 301 8.99 56 AL 52 ANL92 Tr460×5 540 510 510 462.5 32 15 60 1 21 M12×1.75 482 26.9 92 ALL88
60 Tr300×4 380 340 356 302 24 12 40 0.8 18 M10×1.5 326 11.7 60 60 96 Tr480×5 560 530 530 482.5 36 15 60 1 21 M12×1.75 502 28.3 96 96
64 Tr320×5 400 360 376 322.5 24 12 42 0.8 18 M10×1.5 345 13.0 64 64 100 Tr500×5 580 550 550 502.5 36 15 68 1 21 M12×1.75 522 33.6 /500 96
[Notes] 1) Basic profile and dimension of screw thread are in accordance with JIS B 0216.
AN 68 Tr340×5 440 400 410 342.5 28 15 55 1 21 M12×1.75 372 23.0 68 AL 68 2) Basic profile and dimension of bore with internal thread are in accordance with JIS B 0205.
72 Tr360×5 460 420 430 362.5 28 15 58 1 21 M12×1.75 392 25.0 72 68 3) Applicable to adapter sleeve series A31, A32, A23 and A30.
76 Tr380×5 490 450 454 382.5 32 18 60 1 21 M12×1.75 414 30.8 76 76
AN 80 Tr400×5 520 470 484 402.5 32 18 62 1 27 M16×2 439 36.7 80 AL 80

84 Tr420×5 540 490 504 422.5 32 18 70 1 27 M16×2 459 43.3 84 80
88 Tr440×5 560 510 520 442.5 36 20 70 1 27 M16×2 477 45.1 88 88
AN 92 Tr460×5 580 540 540 462.5 36 20 75 1 27 M16×2 497 50.2 92 AL 88

96 Tr480×5 620 560 580 482.5 36 20 75 1 27 M16×2 527 62.0 96 96
100 Tr500×5 630 580 584 502.5 40 23 80 1 27 M16×2 539 63.1 /500 100
ANL44 Tr220×4 260 242 242 222 20 9 30 0.8 12 M 6×1 229 3.09 44 ALL44
48 Tr240×4 290 270 270 242 20 10 34 0.8 15 M 8×1.25 253 5.16 48 48
52 Tr260×4 310 290 290 262 20 10 34 0.8 15 M 8×1.25 273 5.67 52 48
ANL56 Tr280×4 330 310 310 282 24 10 38 0.8 15 M 8×1.25 293 6.78 56 ALL56
60 Tr300×4 360 336 336 302 24 12 42 0.8 15 M 8×1.25 316 9.62 60 60
64 Tr320×5 380 356 356 322.5 24 12 42 0.8 15 M 8×1.25 335 9.94 64 64
ANL68 Tr340×5 400 376 376 342.5 24 12 45 1 15 M 8×1.25 355 11.7 68 ALL64
72 Tr360×5 420 394 394 362.5 28 13 45 1 15 M 8×1.25 374 12.0 72 72
76 Tr380×5 450 422 422 382.5 28 14 48 1 18 M10×1.5 398 14.9 76 76
[Notes] 1) Basic profile and dimension of screw thread are in accordance with JIS B 0216.
2) Basic profile and dimension of bore with internal thread are in accordance with JIS B 0205.
3) Applicable to adapter sleeve series A31, A32, A23 and A30.
C 167 C 168
Locknuts
for withdrawal sleeves
HN 42 ∼ 110 HNL 69 ∼ 108
HNL 41 ∼ 64
g B
b
h 30°
r1
G
d2
u d6 u d1
Locknut Thread1) Standard dimensions (Refer.) Locknut Thread1) Standard dimensions (Refer.)
No. size (mm) Mass Withdrawal sleeve No. No. size (mm) Mass Withdrawal sleeve No.
r1 (kg) r1
G d2 d1 g d6 b h B G d2 d1 g d6 b h B (kg)
max. max.
HN 42 Tr210×4 270 238 250 212 20 10 30 0.8 4.75 AH3138 AH2238 AH3238 AH2338 HNL 69 Tr345×5 410 384 384 347.5 28 13 45 1 11.5 3064 ⎯ ⎯ ⎯
44 Tr220×4 280 250 260 222 20 10 32 0.8 5.35 3140 2240 3240 2340 73 Tr365×5 430 404 404 367.5 28 13 48 1 14.2 3068 ⎯ ⎯ ⎯
48 Tr240×4 300 270 280 242 20 10 34 0.8 6.20 3144 2244 ⎯ 2344
HNL 77 Tr385×5 450 422 422 387.5 28 14 48 1 15.0 AH3072 ⎯ ⎯ ⎯
HN 52 Tr260×4 330 300 306 262 24 12 36 0.8 8.55 AH3148 AH2248 ⎯ AH2348 82 Tr410×5 480 452 452 412.5 32 14 52 1 19.0 3076 ⎯ ⎯ ⎯
58 Tr290×4 370 330 346 292 24 12 40 0.8 11.8 3152 2252 ⎯ 2352 86 Tr430×5 500 472 472 432.5 32 14 52 1 19.8 3080 ⎯ ⎯ ⎯
62 Tr310×5 390 350 366 312.5 24 12 42 0.8 13.4 3156 2256 ⎯ 2356
HNL 90 Tr450×5 520 490 490 452.5 32 15 60 1 23.8 AH3084 ⎯ ⎯ ⎯
HN 66 Tr330×5 420 380 390 332.5 28 15 52 1 20.4 AH3160 AH2260 AH3260 ⎯ 94 Tr470×5 540 510 510 472.5 32 15 60 1 25.0 X3088 ⎯ ⎯ ⎯
70 Tr350×5 450 410 420 352.5 28 15 55 1 25.2 3164 2264 3264 ⎯ 98 Tr490×5 580 550 550 492.5 36 15 60 1 34.0 X3092 ⎯ ⎯ ⎯
74 Tr370×5 470 430 440 372.5 28 15 58 1 28.2 3168 ⎯ 3268 ⎯
HNL104 Tr520×6 600 570 570 523 36 15 68 1 37.0 AHX3096 ⎯ ⎯ ⎯
HN 80 Tr400×5 520 470 484 402.5 32 18 62 1 40.0 AH3172 ⎯ AH3272 ⎯ 108 Tr540×6 630 590 590 543 40 20 68 1 43.5 X30/500 ⎯ ⎯ ⎯
84 Tr420×5 540 490 504 422.5 32 18 70 1 46.9 3176 ⎯ 3276 ⎯
[Note] 1) Basic profile and dimension of screw thread are in accordance with JIS B 0216.
88 Tr440×5 560 510 520 442.5 36 20 70 1 48.5 3180 ⎯ 3280 ⎯
[Remark] Number of slots on nut may sometimes exceed that shown in the figure.
HN 92 Tr460×5 580 540 540 462.5 36 20 75 1 55.0 AH3184 ⎯ AH3284 ⎯

96 Tr480×5 620 560 580 482.5 36 20 75 1 67.0 X3188 ⎯ X3288 ⎯
102 Tr510×6 650 590 604 513 40 23 80 1 75.0 X3192 ⎯ X3292 ⎯
HN 106 Tr530×6 670 610 624 533 40 23 80 1 78.0 AHX3196 ⎯ AHX3296 ⎯

110 Tr550×6 700 640 654 553 40 23 80 1 92.5 X31/500 ⎯ X32/500 ⎯
HNL 41 Tr205×4 250 232 234 207 18 8 30 0.8 3.43 AH3038 AH238 ⎯ ⎯
43 Tr215×4 260 242 242 217 20 9 30 0.8 3.72 3040 240 ⎯ ⎯
47 Tr235×4 280 262 262 237 20 9 34 0.8 4.60 3044 244 ⎯ ⎯
HNL 52 Tr260×4 310 290 290 262 20 10 34 0.8 5.80 AH3048 AH248 ⎯ ⎯
56 Tr280×4 330 310 310 282 24 10 38 0.8 6.72 3052 252 ⎯ ⎯
60 Tr300×4 360 336 336 302 24 12 42 0.8 9.60 3056 256 ⎯ ⎯
HNL 64 Tr320×5 380 356 356 322.5 24 12 42 1 10.3 AH3060 ⎯ ⎯ ⎯
[Note] 1) Basic profile and dimension of screw thread are in accordance with JIS B 0216.
[Remark] Number of slots on nut may sometimes exceed that shown in the figure.
C 169 C 170
Lockwashers
AW 00 ∼ 24(X) AW 25 ∼ 40(X)
ƒ 25° AWL24 ∼ 40(X)
r2
B2
ƒ1
M u d4 u d5
d3 B1
With bent inner tongue With flat inner tongue
Lockwasher No. Standard dimensions No. (Refer.) Applicable Applicable Lockwasher No. Standard dimensions No. (Refer.) Applicable Applicable
(mm) of Mass adapter locknut (mm) of Mass adapter locknut
With bent With flat tooth (kg/100pcs.) sleeve No. With bent With flat
d3 M ƒ1 B1 ƒ d4 d5 r2 B2 d3 M ƒ1 B1 ƒ d4 d5 r2 B2 tooth (kg/100pcs.) sleeve No.
inner tongue inner tongue (bore No.) inner tongue inner tongue (bore No.)
AW 00 AW 00X 10 8.5 3 1 3 13 21 0.5 2 9 0.131 ⎯ AN 00 AW 25 AW 25X 125 120 14 2 12 148 170 1.5 6 19 11.8 ⎯ 25
01 01X 12 10.5 3 1 3 17 25 0.5 2 9 0.192 ⎯ 01 26 26X 130 125 14 2 12 149 175 1.5 6 19 11.3 26 26
02 02X 15 13.5 4 1 4 21 28 1 2.5 13 0.253 ⎯ 02
AW 27 AW 27X 135 130 14 2 14 160 185 1.5 6 19 14.4 ⎯ AN 27
AW 03 AW 03X 17 15.5 4 1 4 24 32 1 2.5 13 0.313 ⎯ AN 03 28 28X 140 135 16 2 14 160 192 1.5 8 19 14.2 28 28
04 04X 20 18.5 4 1 4 26 36 1 2.5 13 0.350 04 04 29 29X 145 140 16 2 14 172 202 1.5 8 19 16.8 ⎯ 29
05 05X 25 23 5 1.2 5 32 42 1 2.5 13 0.640 05 05
AW 30 AW 30X 150 145 16 2 14 171 205 1.5 8 19 15.5 30 AN 30
AW 06 AW 06X 30 27.5 5 1.2 5 38 49 1 2.5 13 0.780 06 AN 06 31 31X 155 147.5 16 2.5 16 182 212 1.5 8 19 20.9 ⎯ 31
07 07X 35 32.5 6 1.2 5 44 57 1 2.5 15 1.04 07 07 32 32X 160 154 18 2.5 16 182 217 1.5 8 19 22.2 32 32
08 08X 40 37.5 6 1.2 6 50 62 1 2.5 15 1.23 08 08
AW 33 AW 33X 165 157.5 18 2.5 16 193 222 1.5 8 19 24.1 ⎯ AN 33
AW 09 AW 09X 45 42.5 6 1.2 6 56 69 1 2.5 17 1.52 09 AN 09 34 34X 170 164 18 2.5 16 193 232 1.5 8 19 24.7 34 34
10 10X 50 47.5 6 1.2 6 61 74 1 2.5 17 1.60 10 10 36 36X 180 174 20 2.5 18 203 242 1.5 8 19 26.8 36 36
11 11X 55 52.5 8 1.2 7 67 81 1 4 17 1.96 11 11
AW 38 AW 38X 190 184 20 2.5 18 214 252 1.5 8 19 27.8 38 AN 38
AW 12 AW 12X 60 57.5 8 1.5 7 73 86 1.2 4 17 2.53 12 AN 12 40 40X 200 194 20 2.5 18 226 262 1.5 8 19 29.3 40 40
13 13X 65 62.5 8 1.5 7 79 92 1.2 4 19 2.90 13 13
14 14X 70 66.5 8 1.5 8 85 98 1.2 4 19 3.34 14 14
AWL24 AWL24X 120 115 14 2 12 133 155 1.5 6 19 7.70 24 ANL24
AW 15 AW 15X 75 71.5 8 1.5 8 90 104 1.2 4 19 3.56 15 AN 15 26 26X 130 125 14 2 12 143 165 1.5 6 19 8.70 26 26
16 16X 80 76.5 10 1.8 8 95 112 1.2 4 19 4.64 16 16 28 28X 140 135 16 2 14 151 175 1.5 8 19 10.9 28 28
17 17X 85 81.5 10 1.8 8 102 119 1.2 4 19 5.24 17 17
AWL30 AWL30X 150 145 16 2 14 164 190 1.5 8 19 11.3 30 ANL30
AW 18 AW 18X 90 86.5 10 1.8 10 108 126 1.2 4 19 6.23 18 AN 18 32 32X 160 154 18 2.5 16 174 200 1.5 8 19 16.2 32 32
19 19X 95 91.5 10 1.8 10 113 133 1.2 4 19 6.70 19 19 34 34X 170 164 18 2.5 16 184 210 1.5 8 19 19.0 34 34
20 20X 100 96.5 12 1.8 10 120 142 1.2 6 19 7.65 20 20
AWL36 AWL36X 180 174 20 2.5 18 192 220 1.5 8 19 18.0 36 ANL36
AW 21 AW 21X 105 100.5 12 1.8 12 126 145 1.2 6 19 8.26 21 AN 21 38 38X 190 184 20 2.5 18 202 230 1.5 8 19 20.5 38 38
22 22X 110 105.5 12 1.8 12 133 154 1.2 6 19 9.40 22 22 40 40X 200 194 20 2.5 18 218 250 1.5 8 19 21.4 40 40
23 23X 115 110.5 12 2 12 137 159 1.5 6 19 10.8 ⎯ 23 [Remark] 1) AW00~AW40, AW00X~AW40X are applicable to adapter assembly series H31, H2, H3 and H23.
2) AWL24~AWL40, AWL24X~AWL40X are applied to adapter assembly series H30.
AW 24 AW 24X 120 115 14 2 12 138 164 1.5 6 19 10.5 24 AN 24 3) For adapter sleeves with narrow slits, lockwashers with flat inner tongue should be used. Either type of
lockwasher can be used for adapter sleeves with wide slits.
[Remark] 1) AW00~AW40, AW00X~AW40X are applicable to adapter assembly series H31, H2, H3 and H23.
2) AWL24~AWL40, AWL24X~AWL40X are applied to adapter assembly series H30.
3) For adapter sleeves with narrow slits, lockwashers with flat inner tongue should be used. Either type of
lockwasher can be used for adapter sleeves with wide slits.
C 171 C 172
Lock plates
AL 44 ∼ 100
ALL44 ∼ 96 B3
B3
u d7 L1 L3
L2 B4
Standard dimensions (Refer.) Applicable

Lock plate Mass
(mm) locknut
No. B3 B4 L2 d7 L1 L3 (kg/100pcs.) No.
AL 44 4 20 12 9 22.5 30.5 2.60 AN 44,48
52 4 24 12 12 25.5 33.5 3.39 52,56
60 4 24 12 12 30.5 38.5 3.79 60
AL 64 5 24 15 12 31 41 5.35 AN 64
68 5 28 15 14 38 48 6.65 68,72
76 5 32 15 14 40 50 7.96 76
AL 80 5 32 15 18 45 55 8.20 AN 80,84
88 5 36 15 18 43 53 9.00 88,92
96 5 36 15 18 53 63 10.4 96
100 5 40 15 18 45 55 10.5 100
ALL44 4 20 12 7 13.5 21.5 2.12 ANL44

48 4 20 12 9 17.5 25.5 2.29 48,52
56 4 24 12 9 17.5 25.5 2.92 56
ALL60 4 24 12 9 20.5 28.5 3.16 ANL60

64 5 24 15 9 21 31 4.56 64,68
72 5 28 15 9 20 30 5.03 72
ALL76 5 28 15 12 24 34 5.28 ANL76,80

84 5 32 15 12 24 34 6.11 84
88 5 32 15 14 28 38 6.45 88,92
96 5 36 15 14 28 38 7.29 96,100
[Remark] Lock plate series AL are applicable to adapter assembly series H31, H32 and H23, while lock plate
series ALL are applicable to H30.
C 173 C 174

Catb2001e C

Uploaded by

Copyright:

Available Formats

Catb2001e C

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Catb2001e C

Uploaded by

Copyright:

Available Formats

Ceramic&Exsev bearing series Exsev bearings for use in

More and more bearings are being used in extreme special

¡Exsev bearings for use in a clean environment

¡Exsev bearings for use in a vacuum environment

¡For details, refer to JTEKT separate catalog "Ceramic

Bearing material range thermal

Graphite (GF) ' + 500 max. − 2.15 − 5.5 # × # # # # # # # # # # # '

Reinforced fluorocarbon resin (FA) ' − 100 to + 200 Atmospheric

Reinforced PEEK resin (PN) ' − 100 to + 300 Atmospheric

Cleanness (class 1005) ) − − − class 105) − − − −

Corrosion resistance 2) # # # − # " − − −

Inner ring and Precipitation Non-magnetic High carbon High speed

Martensitic stainless steel

Vacuum Cage coated with Balls coated with 3)

Equivalent load / load rating

where, (3) Ceramic bearing service life

Boundary dimensions Bearing No. (Refer.) Basicbearing

Boundary dimensions Bearing No. (Refer.) Basicbearing

30 55 13 1 SV 6006 ZZST SE 6006 ZZSTMSA7 SE 6006 ZZSTMG3 6006 13.2 8.25

35 62 14 1 SV 6007 ZZST SE 6007 ZZSTMSA7 SE 6007 ZZSTMG3 6007 15.9 10.3

40 68 15 1 SV 6008 ZZST SE 6008 ZZSTMSA7 SE 6008 ZZSTMG3 6008 16.7 11.5

Boundary dimensions Bearing No.

5 14 5 0.2 SE 605 ZZSTPRA SE 605 ZZSTPR SE 605 ZZSTPRB

6 12 4 ⎯ SEWML6012-1 ZZSTPRA SEWML6012-1 ZZSTPR SEWML6012-1 ZZSTPRB

7 19 6 0.3 SE 607 ZZSTPRA SE 607 ZZSTPR SE 607 ZZSTPRB

8 22 7 0.3 SE 608 ZZSTPRA SE 608 ZZSTPR SE 608 ZZSTPRB

9 24 7 0.3 SE 609 ZZSTPRA SE 609 ZZSTPR SE 609 ZZSTPRB

10 26 8 0.3 SE 6000 ZZSTPRA SE 6000 ZZSTPR SE 6000 ZZSTPRB

12 28 8 0.3 SE 6001 ZZSTPRA SE 6001 ZZSTPR SE 6001 ZZSTPRB

15 32 9 0.3 SE 6002 ZZSTPRA SE 6002 ZZSTPR SE 6002 ZZSTPRB

17 35 10 0.3 SE 6003 ZZSTPRA SE 6003 ZZSTPR SE 6003 ZZSTPRB

20 42 12 0.6 SE 6004 ZZSTPRA SE 6004 ZZSTPR SE 6004 ZZSTPRB

25 47 12 0.6 SE 6005 ZZSTPRA SE 6005 ZZSTPR SE 6005 ZZSTPRB

Boundary dimensions Bearing No.

30 55 13 1 SE 6006 ZZSTPRA SE 6006 ZZSTPR SE 6006 ZZSTPRB

35 62 14 1 SE 6007 ZZSTPRA SE 6007 ZZSTPR SE 6007 ZZSTPRB

40 68 15 1 SE 6008 ZZSTPRA SE 6008 ZZSTPR SE 6008 ZZSTPRB

Boundary dimensions Bearing No.

4 12 4 0.2 ⎯ 3NC604MD4 3NC604YH4 3NC604ST4 ⎯ NC604

5 14 5 0.2 ⎯ 3NC605MD4 3NC605YH4 3NC605ST4 ⎯ NC605

6 17 6 0.3 3NC606HT4 GF 3NC606MD4 3NC606YH4 3NC606ST4 NC706V NC606

7 19 6 0.3 3NC607HT4 GF 3NC607MD4 3NC607YH4 3NC607ST4 NC707V NC607

8 22 7 0.3 3NC608HT4 GF 3NC608MD4 3NC608YH4 3NC608ST4 NC708V NC608

9 24 7 0.3 3NC609HT4 GF 3NC609MD4 3NC609YH4 3NC609ST4 NC709V NC609

10 26 8 0.3 3NC6000HT4 GF 3NC6000MD4 3NC6000YH4 3NC6000ST4 NC7000V NC6000

12 28 8 0.3 3NC6001HT4 GF 3NC6001MD4 3NC6001YH4 3NC6001ST4 NC7001V NC6001

15 32 9 0.3 3NC6002HT4 GF 3NC6002MD4 3NC6002YH4 3NC6002ST4 NC7002V NC6002

17 35 10 0.3 3NC6003HT4 GF 3NC6003MD4 3NC6003YH4 3NC6003ST4 NC7003V NC6003

20 42 12 0.6 3NC6004HT4 GF 3NC6004MD4 3NC6004YH4 3NC6004ST4 NC7004V NC6004

25 47 12 0.6 3NC6005HT4 GF 3NC6005MD4 3NC6005YH4 3NC6005ST4 NC7005V NC6005

Boundary dimensions Bearing No.

30 55 13 1 3NC6006HT4 GF 3NC6006MD4 3NC6006YH4 3NC6006ST4 NC7006V NC6006

35 62 14 1 3NC6007HT4 GF 3NC6007MD4 3NC6007YH4 3NC6007ST4 NC7007V NC6007

40 68 15 1 3NC6008HT4 GF 3NC6008MD4 3NC6008YH4 3NC6008ST4 NC7008V NC6008

Boundary dimensions Bearing No. (Refer.) Basicbearing

15 32 9 0.3 0.15 3NC 7002 FT ⎯ ⎯ 7002 6.10 3.45 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯

20 42 12 0.6 0.3 3NC 7004 FT ⎯ ⎯ 7004 10.3 6.10 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯

25 47 12 0.6 0.3 3NC 7005 FT ⎯ ⎯ 7005 11.3 7.40 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯

50 72 12 0.6 0.3 ⎯ 3NC HAR910C FT ⎯ ⎯ ⎯ ⎯ HAR910C 9.10 6.30 ⎯ ⎯ ⎯