Experiment NO.3

University of Technology
Laser and Optoelectronics Engineering Department

DC circuits analysis laboratory 2011-2012
Experiment NO.3
Series and parallel connection
Object
To study the properties of series and parallel connection.
Apparatus
1. DC circuit training system
2. Set of wires.
3. DC Power supply
4. Digital A.V.O. meter
Theory
1. The Series Circuit
A SERIES CIRCUIT or ‘‘series-connected circuit’’ is a circuit having JUST
ONE CURRENT PATH. Thus, Fig.(1) is an example of a ‘‘series circuit’’ in
which a battery of constant potential difference V volts, and three resistances,
are all connected ‘‘in series.’’
There are two ways to connect the resistance
1. Resistance in series
When some conductors having resistance R1 – R2 – R3 etc. are joined end –

on
Fig.(1)
Laser and Optoelectronics Engineering
Department DC circuits analysis laboratory
Since a series circuit has just one current path, it follows that all the
components in a series circuit CARRY THE SAME CURRENT I, a fact
evident from inspection of Fig.(1).
The current I is assumed to be a flow of positive charge, and thus flows out
of the positive terminal of the battery and around through the external circuit,
reentering the battery at the negative terminal. This is indicated by the arrows in
Fig.(1).
In a series circuit, the TOTAL resistance, RT, that the battery sees is equal to
the SUM of the individual resistances. Thus, in the particular case of Fig.(1) the
battery sees a total resistance, RT = R1 + R2 + R3, while in the general case of
‘‘n’’ resistances connected in series the battery sees a total resistance of :
RT = R1 + R2 + R3 +…..Rn
By Ohm’s law, it follows that the current I in a series circuit is equal to
Resistance, on the other hand, consumes electrical energy, removing it from

the circuit in the form of heat. Since resistance does not produce or generate
electrical energy, it is a non-active or PASSIVE type of circuit element.
The potential difference between the terminals of a resistor is called the
VOLTAGE DROP across the resistor, and, is equal to the current I times the
resistance R; that is, the ‘‘voltage drop’’ across a resistance of R ohms
carrying a current of I amperes is IR volts.
We have the important fact that:
In a series circuit, the applied voltage is equal to the sum of the

voltage drops.
It should be pointed out that the voltage drop across a resistor is always from
plus to minus in the direction of the current flow, a fact illustrated in Fig.(2).
Fig.(2)
2. The Parallel Circuit

A PARALLEL circuit is one in which the battery current divides into a number
of ‘‘parallel paths.’’ This is shown in Fig.(3), in which a battery, of constant V
volts, delivers a current of I amperes to a load consisting of any number of n
resistances connected ‘‘in parallel.’’
Fig.(3)
The currents in the individual resistances are called the ‘‘branch currents,’’
and the battery current I is often called the ‘‘line current.’’ From inspection of
Fig.(3) we see that, in a parallel circuit, the battery current I is equal to the sum
of the branch currents.
If the battery voltage V is applied equally to all n resistances; that is, the
same voltage V is applied to all the parallel branches. Hence, by Ohm’s law, the
individual branch currents in Fig.(3) have the values:
Then, we have:
Now let RT be the total resistance as seen by the battery in Fig.(3). Then, by
Ohm’s law, it has to be true that:
Since the left-hand sides of the last two equations are equal, the two right-
hand sides are also equal. Setting the two right-hand sides equal, then canceling
the Vs, gives
Procedure
1. Using the DC circuit trainer, connect the circuit Shown in Fig. (4), take
VT =10V, and R1=82Ω, R2 = 100Ω and R3 =150Ω.
2. Measured the voltage and current of "R1 , R2 & R3", then record it in
table below
82 100 150
V(volt) VT =
I(mA) IT =
3. By using
ohm's law, Calculate the RT
4. Disconnect the DC power supply, and then measured the equivalent
resistance by using the AVO meter only.
82
V
10V 100
V
V
150
Fig.(4)
5. Using the DC circuit trainer, connect the circuit Shown in Fig.(5), and
take VT =10V, and R1=82Ω, R2 = 100Ω and R3 =150Ω.
6. Measured the voltage and current of "R1 , R2 & R3", then record it in
table below
7. Disconnect the DC power supply, and then measured the equivalent

resistance by using the AVO meter only.
82 100 150
I (mA) IT=
V(volt) VT=
10V
82 100 150
Fig.(5)
Discussion
1. Tow resistors (R1, R2) are connect in parallel, prove that
R1 R2
RT =
R1 + R2
2. For the circuit shown below, find RT, V2.

3.In Figure, the battery voltage is V = 65 volts, and the values of the
resistances, in ohms, are 38, 17, and 27, as shown. Find:
(a) Total resistance seen by the battery,
(b) Current measured by the ammeters shown in the figure,
(c) Power output of the battery,
(d) Power input to each resistor.

Experiment NO.3

Uploaded by

Copyright:

Available Formats

Experiment NO.3

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Experiment NO.3

Uploaded by

Copyright:

Available Formats

University of Technology

Laser and Optoelectronics Engineering Department

There are two ways to connect the resistance

When some conductors having resistance R1 – R2 – R3 etc. are joined end –

By Ohm’s law, it follows that the current I in a series circuit is equal to

Resistance, on the other hand, consumes electrical energy, removing it from

We have the important fact that:

In a series circuit, the applied voltage is equal to the sum of the

2. The Parallel Circuit

82 100 150

7. Disconnect the DC power supply, and then measured the equivalent

82 100 150

1. Tow resistors (R1, R2) are connect in parallel, prove that

2. For the circuit shown below, find RT, V2.

You might also like