Multi-Range DC Power Supply: PSW Series

Multi-Range DC Power Supply
PSW Series
PROGRAMMING MANUAL
ISO-9001 CERTIFIED MANUFACTURER

This manual contains proprietary information, which is protected by
copyright. All rights are reserved. No part of this manual may be
photocopied, reproduced or translated to another language without
prior written consent of Good Will company.
The information in this manual was correct at the time of printing.

However, Good Will continues to improve products and reserves the
rights to change specification, equipment, and maintenance
procedures at any time without notice.
Good Will Instrument Co., Ltd.

No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan.
Table of Contents
Table of Contents
SAFETY INSTRUCTIONS .................................................. 4
GETTING STARTED .......................................................... 7

PSW Series Overview ................................................... 8
Appearance ................................................................ 14
Configuration Settings ............................................... 21
REMOTE CONTROL ....................................................... 29

Interface Configuration .............................................. 30
Socket Server Examples ............................................. 44
Command Syntax ....................................................... 48
Command List ........................................................... 52
Status Register Overview ..........................................101
Error List ..................................................................111
APPENDIX .................................................................... 120

PSW Default Settings ................................................120
Error Messages & Messages .....................................123
LED Display Format ..................................................123
INDEX .......................................................................... 124
3
PSW Series Programming Manual
SAFETY INSTRUCTIONS
This chapter contains important safety
instructions that you must follow during
operation and storage. Read the following before
any operation to insure your safety and to keep
the instrument in the best possible condition.
Safety Symbols
These safety symbols may appear in this manual or on the
instrument.
Warning: Identifies conditions or practices that

WARNING could result in injury or loss of life.
Caution: Identifies conditions or practices that

CAUTION could result in damage to the PSW or to other
properties.
DANGER High Voltage
Attention Refer to the Manual
Protective Conductor Terminal
Earth (ground) Terminal
4
SAFETY INSTRUCTIONS
Do not dispose electronic equipment as unsorted

municipal waste. Please use a separate collection
facility or contact the supplier from which this
instrument was purchased.
Safety Guidelines
General  Do not place any heavy object on the PSW.

Guideline  Avoid severe impact or rough handling that
leads to damaging the PSW.
CAUTION
 Do not discharge static electricity to the PSW.
 Use only mating connectors, not bare wires, for
the terminals.
 Do not block the cooling fan opening.
 Do not disassemble the PSW unless you are
qualified.
Power Supply  AC Input voltage rating: 100Vac-240Vac +/-10%
 Frequency: 47Hz~63Hz
WARNING
 To avoid electrical shock connect the protective
grounding conductor of the AC power cord to
an earth ground.
Cleaning the PSW  Disconnect the power cord before cleaning.

 Use a soft cloth dampened in a solution of mild
detergent and water. Do not spray any liquid.
 Do not use chemicals containing harsh material
such as benzene, toluene, xylene, and acetone.
Operation  Location: Indoor, no direct sunlight, dust free,

Environment almost non-conductive pollution (Note below)
 Relative Humidity: 20%~ 85%
 Altitude: < 2000m
 Temperature: 0°C to 50°C
5
 Mains supply voltage fluctuations: +/-10 %

 Overvoltage category: OVC II
 If the equipment is used in a manner not
specified by the manufacturer, the protection
provided by the equipment may be impaired.
 LAN, RS232/RS485, USB, and GPIB ports are
only to be connected to the circuits which are
separated from mains supply by double /
reinforce insulation.
(Pollution Degree) EN61010-1 and EN61010-2-030 specify the
pollution degrees and their requirements as follows. The PSW falls
under degree 2.
Pollution refers to “addition of foreign matter, solid, liquid, or
gaseous (ionized gases), that may produce a reduction of dielectric
strength or surface resistivity”.
 Pollution degree 1: No pollution or only dry, non-conductive
pollution occurs. The pollution has no influence.
 Pollution degree 2: Normally only non-conductive pollution
occurs. Occasionally, however, a temporary conductivity caused
by condensation must be expected.
 Pollution degree 3: Conductive pollution occurs, or dry, non-
conductive pollution occurs which becomes conductive due to
condensation which is expected. In such conditions, equipment
is normally protected against exposure to direct sunlight,
precipitation, and full wind pressure, but neither temperature
nor humidity is controlled.
Storage  Location: Indoor

environment  Temperature: -25°C to 70°C
 Relative Humidity: <90%
Disposal Do not dispose this instrument as unsorted
municipal waste. Please use a separate collection
facility or contact the supplier from which this
instrument was purchased. Please make sure
discarded electrical waste is properly recycled to
reduce environmental impact.
6
GETTING STARTED
GETTING STARTED
This chapter describes the power supply in a
nutshell, including its main features and front /
rear panel introduction, as well as an overview of
the configuration settings.
PSW Series Overview ................................................... 8

Series lineup ............................................................................................... 8
Main Features ............................................................................................ 9
Accessories .............................................................................................. 10
PSW 30/40/80/160 Accessories ............................................... 10
PSW 250/800 Accessories .......................................................... 12
Appearance ................................................................ 14
PSW Front Panel .................................................................................... 14
Rear Panel ................................................................................................ 17
Configuration Settings ............................................... 21
Setting Normal Function Settings ....................................................... 21
Setting Power On Configuration Settings .......................................... 22
Configuration Table ............................................................................... 24
7
PSW Series Overview
Series lineup
The PSW series consists of 18 models, divided into 3 different
model types covering 3 power capacities: Type I (360 Watt), Type II
(720 Watt) and Type III (1080 Watt).
Throughout the user manual, PSW 30, PSW 40,

Note PSW 80, PSW 160, PSW 250 or PSW 800 will refer
to any of the PSW models with a maximum
voltage rating of 30V, 40V, 80V, 160V, 250V or
800V, respectively.
Model name Type Voltage Rating Current Rating Power

PSW 30-36 Type I 0~30V 0~36A 360W
PSW 40-27 Type I 0~40V 0~27A 360W
PSW 80-13.5 Type I 0~80V 0~13.5A 360W
PSW 160-7.2 Type I 0~160V 0~7.2A 360W
PSW 250-4.5 Type I 0~250V 0~4.5A 360W
PSW 800-1.44 Type I 0~800V 0~1.44A 360W
PSW 30-72 Type II 0~30V 0~72A 720W
PSW 40-54 Type II 0~40V 0~54A 720W
PSW 80-27 Type II 0~80V 0~27A 720W
PSW 160-14.4 Type II 0~160V 0~14.4A 720W
PSW 250-9 Type II 0~250V 0~9A 720W
PSW 800-2.88 Type II 0~800V 0~2.88A 720W
PSW 30-108 Type III 0~30V 0~108A 1080W
PSW 40-81 Type III 0~40V 0~81A 1080W
PSW 80-40.5 Type III 0~80V 0~40.5A 1080W
PSW 160-21.6 Type III 0~160V 0~21.6A 1080W
8
GETTING STARTED
PSW 250-13.5 Type III 0~250V 0~13.5A 1080W

PSW 800-4.32 Type III 0~800V 0~4.32A 1080W
Apart from the differences in output, each unit differs in size. The
720 and 1080 watt models are larger than the 360 watt models to
accommodate the increase in power.
360 Watt models 720 Watt models 1080 Watt models

Type I Type II Type III
Multi-Range DC Power Supply Voltage Multi-Range DC Power Supply Voltage Multi-Range DC Power Supply Voltage
PSW 30-36 360W PSW 30-72 720W PSW 30-108 1080W
VSR VSR VSR

W W W
CV CV CV
V V V
RMT RMT RMT
ALM 20 40 60 80 100 %W ALM 20 40 60 80 100 %W ALM 20 40 60 80 100 %W
Current Current Current
DLY DLY DLY
W W W
CC CC CC
A A A
ISR ISR ISR
Function OVP/OCP Set Function OVP/OCP Set Function OVP/OCP Set

Output Output Output
Test Lock/Local PWR DSPL Test Lock/Local PWR DSPL Test Lock/Local PWR DSPL
Main Features
Performance  High performance/power

 Power efficient switching type power supply
 Low impact on load devices
 Fast transient recovery time of 1ms
 Fast output response time
Features  OVP, OCP and OHP (OTP) protection

 Adjustable voltage and current slew rates
 User adjustable bleeder control to quickly
dissipate the power after shutdown to safe
levels.
 Extensive remote monitoring and control
options
 Support for serial* and parallel connections.
*(30, 40, 80, 160 volt models only)
9
 Power on configuration settings.

 Supports test scripts
 Web server monitoring and control
Interface  Ethernet port

 Analog connector for analog voltage and current
monitoring
 USB host and device port
Accessories
Please check the contents before using the PSW.
PSW 30/40/80/160 Accessories
Standard Part number Description

Accessories
CD-ROM User manual, programming
manual
Power cord (Type I/II)
Power cord (Type III)
Output terminal cover
GTL-123 Test leads: 1x red, 1x black
GTL-240 USB Cable
PSW-004 Basic Accessory Kit:
M4 terminal screws and washers
x2, M8 terminal bolts, nuts and
washers x2, Air filter x1, Analog
control protection dummy x1,
Analog control lock level x1
10
GETTING STARTED
Optional Part number Description

Accessories
GET-001 Extended terminal with max. 30A
GET-005 Extended European terminal with
max. 20A
PSW-001 Accessory Kit:
Pin contact x10, Socket x1,
Protection cover x1
PSW-002 Simple IDC Tool
PSW-003 Contact Removal

Tool
PSW-005 Series operation cable for 2 units.

PSW-006 Parallel operation cable for 2 units.
GRA-410-J Rack mount adapter (JIS)
GRA-410-E Rack mount adapter (EIA)
GUG-001 GPIB to USB adapter
GTL-240 USB Cable
PSW-010 Large filter (Type II/III)
GUR-001A RS-232 to USB adapter with M3
rivet nut (Support only when
firmware version is 2.25 or above)
GUR-001B RS-232 to USB adapter with #4-40
UNC rivet nut (Support only when
Download Name Description
psw_cdc.inf USB driver
11
PSW 250/800 Accessories
Standard Part number Description

Accessories
CD-ROM User manual, programming
manual
Power cord (Type I/II)
Power cord (Type III)
High voltage output terminal cover
GTL-240 USB Cable
High voltage output terminal
PSW-008 Basic Accessory Kit:
(Air filter x1, Analog control
protection dummy x1, Analog
control lock level x1
Optional Part number Description
Accessories
GET-002 Extended terminal with max. 10A
PSW-001 Accessory Kit:
Pin contact x10, Socket x1,
Protection cover x1
PSW-002 Simple IDC Tool
PSW-003 Contact Removal

Tool

GRA-410-J Rack mount adapter (JIS)
GRA-410-E Rack mount adapter (EIA)
GTL-130 Test leads: 2x red, 2x black
12
GETTING STARTED
GUG-001 GPIB to USB adapter

GTL-240 USB Cable
PSW-010 Large filter (Type II/III)
GUR-001A RS-232 to USB adapter with M3
rivet nut (Support only when
GUR-001B RS-232 to USB adapter with #4-40
UNC rivet nut (Support only when
Download Name Description
psw_cdc.inf USB driver
13
Appearance
PSW Front Panel

720W: PSW 30-72, 40-54, 80-27, 160-14.4, 250-9, 800-2.88
PSW 30-72
720W
Voltage
Voltage
Display VSR
CV
W knob
V
RMT
ALM 20 40 60 80 100 %W
Current
DLY
CC
W Current
A
Cover
ISR
knob
panel Function OVP/OCP Set
Output
Output
Test Lock/Local PWR DSPL key
Power
switch Function
keys
USB A
port
1080W: PSW 30-108, 40-81, 80-40.5, 160-21.6, 360W: PSW 30-36,

250-13.5, 800-4.32 40-27, 80-13.5, 160-
7.2, 250-4.5, 800-1.44
Multi-Range DC Power Supply Voltage Multi-Range DC Power Supply Voltage

PSW 30-108 1080W PSW 30-36 360W
VSR VSR
W W
CV CV
V V
RMT RMT
ALM 20 40 60 80 100 %W ALM 20 40 60 80 100 %W
Current Current
DLY DLY
W W
CC CC
A A
ISR ISR
Function OVP/OCP Set Function OVP/OCP Set

Output Output
Test Lock/Local PWR DSPL Test Lock/Local PWR DSPL
14
GETTING STARTED
Function Keys The Function keys along with the Output key will
light up when a key is active.
Function The Function key is used to

configure the power supply.
OVP/OCP Set the over current or over

voltage protection levels.
Set Sets the current and voltage limits.
Test Used to run customized scripts for

testing.
Lock/Local Locks or unlocks the panel keys to

prevent accidentally changing
panel settings.
PWR DSPL Toggles the display from viewing

V/A  V/W or A/W*.
*Press the Voltage knob for V/W,
press the Current knob for A/W.
Display VSR Voltage Slew Rate

Indicators CV Constant Voltage Mode
RMT Remote Control Mode
ALM Alarm on
DLY Delay Output
CC Constant Current Mode
ISR Current Slew Rate
20 40 60 Power bar
80 100 %W Indicates the current power output
as a percentage.
15
Voltage Knob Voltage

Sets the voltage.
Current Knob Current

Sets the current.
Output Output Press to turn on the output. The

Output key will light up when the
output is active.
USB USB A port for data transfer,

loading test scripts etc.
Power Switch Used to turn the power on/off.
16
GETTING STARTED
Rear Panel
720W: PSW 30-72, 40-54, 80-27, 160-14.4
Analog control Sense+ USB B Output

connector terminal port terminal
(+)
Chassis
ground
Sense- SER.NO. LABEL
terminal
Output
terminal (-)
Fan
LAN
LAN
AC 100 240V
47 63Hz 1000VA MAX.
AC Input
1080W: PSW 30-108, 40-81, 80-40.5, 160-21.6 360W: PSW 30-36,

40-27, 80-13.5,
160-7.2
AC Input
SER.NO. LABEL
AC 100 240V
N L 47 63Hz 500VA MAX.
LAN
AC 100 240V
47 63Hz 1500VA MAX.
LAN
17
720W: PSW 250-9, 800-2.88
Analog control Sense+ USB B Output

connector terminal port terminals +V
Sense-
terminal
V SN.C. S V
SER.NO. LABEL
Chassis
ground
Output
terminals -V
Fan
LAN
LAN
AC 100 240V
47 63Hz 1000VA MAX.
AC Input
1080W: PSW 250-13.5, 800-4.32 360W: PSW 250-4.5,

800-1.44
AC Input
V SN.C. S V V SN.C. S V
SER.NO. LABEL
AC 100 240V
N L 47 63Hz 500VA MAX.
LAN
AC 100 240V
47 63Hz 1500VA MAX.
LAN
18
GETTING STARTED
Analog Control Standard 26 pin MIL connector

Connector (OMRON XG4 IDC plug).
The analog control connector is

used to monitor current and voltage
output, machine status (OVP, OCP,
OHP (OTP) etc.), and for analog
control of the current and voltage
output.
Use an OMRON XG5 IDC socket as

the mating socket.
Output Terminals Positive (+) and negative (-) output

(30, 40, 80, 160 terminals.
volt models)
Chassis ground
Sense (-S) and Sense (+S) terminals.
Output Terminals The 250 and 800 volt models use a 9 pin connector
(250, 800 volt and a plug for the output and sense terminal
models) connections. The plug is a MC420-38109Z plug by
DECA SwitchLab Inc. This plug is also available
separately (GW part number PSW-012).
V SN.C. S V
Positive (V+) and negative (V-)
output terminals (3 of each).
V SN.C. S V
Chassis ground
V SN.C. S V
Sense (-S) and Sense (+S)
terminals.
19
USB B port The USB B port is used for remote

control.
Fans Temperature controlled fans
Ethernet Port LAN The ethernet port is used for remote

control and digital monitoring from
a PC.
Line Voltage Type I: PSW 30-36/40-27/80-13.5/

Input 160-7.2/250-4.5, 800-1.44
Type II: PSW 30-72/40-54/80-27/
(Type I/TypeII)
160-14.4/250-9, 800-2.88
 Voltage Input: 100~240 VAC
 Line frequency: 50Hz/60 Hz
(Automatically switchable)
Line Voltage N L
Type III:
Input PSW 30-108/40-81/80-40.5/
160-21.6/250-13.5/800-4.32
(Type III)  Voltage Input: 100~240 VAC
 Line frequency: 50Hz/60 Hz
(Automatically switchable)
20
GETTING STARTED
Configuration Settings
Configuration of the PSW power supplies is divided into five
different configuration settings: Normal Function, USB/GPIB, LAN,
Power ON Configuration, Calibration Settings and System Settings.
Power ON Configuration differs from the other settings in that the
settings used with Power ON Configuration settings can only be set
during power up. The other configuration settings can be changed
when the unit is already on. This prevents some important
configuration parameters from being changed inadvertently. Power
On Configuration settings are numbered F-90 to F-95 and the other
configuration settings are numbered F-00 to F-61 and F-88 to F-89.
Setting Normal Function Settings
The normal function settings (F-01~F-61, F-88~F-

89) can be easily configured with the Function
key.
 Ensure the load is not connected.

 Ensure the output is off.
Function setting F-89 (Show Version) can only be

Note viewed, not edited.
Configuration settings F-90~F-95 cannot be edited in

the Normal Function Settings. Use the Power On
Configuration Settings. See page 22 for details.
Steps 1. Press the Function key. The Function

function key will light up.
2. The display will show F-01

on the top and the
configuration setting for
F-01 on the bottom.
21
3. Rotate the voltage knob to change Voltage
the F setting.
Range F-00~ F-61, F-88~F-89
4. Use the current knob to set the Current
parameter for the chosen F setting.
5. Press the Voltage knob to save the

configuration setting. ConF will be Voltage
displayed when successful.
Exit Press the Function key again to exit the Function

configuration settings. The function key
light will turn off.
Setting Power On Configuration Settings

The Power On configuration settings can only be
Background changed during power up to prevent the
configuration settings being inadvertently
changed.
 Ensure the load is not connected.

 Ensure the power supply is off.
Steps 1. Hold the Function key whilst PSW 30-36
VSR
CV
W
V
360W
Voltage
turning the power on.

RMT
ALM 20 40 60 80 100 %W
Current
DLY
W
CC
A
ISR
Function OVP/OCP Set

Output
Test Lock/Local PWR DSPL
2. The display will show F-90 on the

top and the configuration setting
for F-90 on the bottom.
22
GETTING STARTED
3. Rotate the voltage knob to change Voltage
the F setting.
Range F-90~ F-95
4. Use the current knob to set the Current
parameter for the chosen F setting.
5. Press the Voltage knob to save the

configuration setting. ConF will be Voltage
displayed when successful.
Exit Cycle the power to save and exit the configuration

settings.
23
Configuration Table
Please use the configuration settings listed below when applying
the configuration settings.
Normal Function
Settings Setting Setting Range
Output ON delay time F-01 0.00s ~ 99.99s
Output OFF delay time F-02 0.00s ~ 99.99s
0 = CV high speed priority
1 = CC high speed priority
V-I mode slew rate select F-03
2 = CV slew rate priority
3 = CC slew rate priority
0.01V/s ~ 60.00V/s (PSW 30-XX)
0.01V/s ~ 80.00V/s (PSW 40-XX)
0.1V/s ~ 160.0V/s (PSW 80-XX)
Rising voltage slew rate F-04
0.1V/s ~ 320.0V/s (PSW 160-XX)
0.1V/s ~ 500.0V/s (PSW 250-XX)
1V/s ~ 1600V/s (PSW 800-XX)
0.01V/s ~ 60.00V/s (PSW 30-XX)
0.01V/s ~ 80.00V/s (PSW 40-XX)
0.1V/s ~ 160.0V/s (PSW 80-XX)
Falling voltage slew rate F-05
0.1V/s ~ 320.0V/s (PSW 160-XX)
0.1V/s ~ 500.0V/s (PSW 250-XX)
1V/s ~ 1600V/s (PSW 800-XX)
0.01A/s ~ 72.00A/s (PSW 30-36)
0.1A/s ~ 144.0A/s (PSW 30-72)
0.1A/s ~ 216.0A/s (PSW 30-108)
0.01A/s ~ 54.00A/s (PSW 40-27)
0.1A/s ~ 108.0A/s (PSW 40-54)
0.1A/s ~ 162.0A/s (PSW 40-81)
0.01A/s ~ 27.00A/s (PSW 80-13.5)
Rising current slew rate F-06
0.01A/s ~ 54.00A/s (PSW 80-27)
0.01A/s ~ 81.00A/s (PSW 80-40.5)
0.01A/s ~ 14.40A/s (PSW 160-7.2)
0.01A/s ~ 28.80A/s (PSW 160-14.4)
0.01A/s ~ 43.20A/s (PSW 160-21.6)
0.001A/s ~ 9.000A/s (PSW 250-4.5)
0.01A/s ~ 18.00A/s (PSW 250-9)
24
GETTING STARTED
0.01A/s ~ 27.00A/s (PSW 250-13.5)

0.001A/s ~ 2.880A/s (PSW 800-1.44)
0.001A/s ~ 5.760A/s (PSW 800-2.88)
0.001A/s ~ 8.640A/s (PSW 800-4.32)
0.01A/s ~ 72.00A/s (PSW 30-36)
0.1A/s ~ 144.0A/s (PSW 30-72)
0.1A/s ~ 216.0A/s (PSW 30-108)
0.01A/s ~ 54.00A/s (PSW 40-27)
0.1A/s ~ 108.0A/s (PSW 40-54)
0.1A/s ~ 162.0A/s (PSW 40-81)
0.01A/s ~ 27.00A/s (PSW 80-13.5)
0.01A/s ~ 54.00A/s (PSW 80-27)
0.01A/s ~ 81.00A/s (PSW 80-40.5)
Falling current slew rate F-07
0.01A/s ~ 14.40A/s (PSW 160-7.2)
0.01A/s ~ 28.80A/s (PSW 160-14.4)
0.01A/s ~ 43.20A/s (PSW 160-21.6)
0.001A/s ~ 9.000A/s (PSW 250-4.5)
0.01A/s ~ 18.00A/s (PSW 250-9)
0.01A/s ~ 27.00A/s (PSW 250-13.5)
0.001A/s ~ 2.880A/s (PSW 800-1.44)
0.001A/s ~ 5.760A/s (PSW 800-2.88)
0.001A/s ~ 8.640A/s (PSW 800-4.32)
0.000Ω ~ 0.833Ω (PSW 30-36)
0.000Ω ~ 0.417Ω (PSW 30-72)
0.000Ω ~ 0.278Ω (PSW 30-108)
0.000Ω ~ 1.481Ω (PSW 40-27)
0.000Ω ~ 0.741Ω (PSW 40-54)
0.000Ω ~ 0.494Ω (PSW 40-81)
0.000Ω ~ 5.926Ω (PSW 80-13.5)
0.000Ω ~ 2.963Ω (PSW 80-27)
Internal resistance 0.000Ω ~ 1.975Ω (PSW 80-40.5)
F-08
setting 0.000Ω ~ 22.222Ω (PSW 160-7.2)
0.000Ω ~ 11.111Ω (PSW 160-14.4)
0.000Ω ~ 7.407Ω (PSW 160-21.6)
0.00Ω ~ 55.55Ω (PSW 250-4.5)
0.00Ω ~ 27.77Ω (PSW 250-9)
0.00Ω ~ 18.51Ω (PSW 250-13.5)
0.0Ω ~ 555.5Ω (PSW 800-1.44)
0.0Ω ~ 277.8Ω (PSW 800-2.88)
0.0Ω ~ 185.1Ω (PSW 800-4.32)
Bleeder circuit control F-09 0 = OFF, 1 = ON, 2 = AUTO
25
Buzzer ON/OFF control F-10 0 = OFF, 1 = ON

Measurement Average
F-17 0 = Low, 1 = Middle, 2 = High
Setting
0 = Panel lock: allow output off
Lock Mode F-19
1 = Panel lock: allow output on/off
USB/GPIB settings
Front panel USB State F-20 0 = Absent, 1 = Mass Storage
0 = Absent, 2 = USB-CDC, 3 = GPIB-
Rear panel USB State F-21
USB adapter
0 = Disable, 1 = USB Host, 2 = Auto
Rear panel USB mode F-22
detect speed, 3 = Full speed only
GPIB address F-23 0~30
LAN settings
MAC Address-1 F-30 0x00~0xFF
LAN F-36 0 = Disable, 1 = Enable
DHCP F-37 0 = Disable, 1 = Enable
IP Address-1 F-39 0~255
Subnet Mask-1 F-43 0~255
Gateway-1 F-47 0~255
DNS address -1 F-51 0~255
DNS address -2 F-52 0~255
DNS address-3 F-53 0~255
DNS address-4 F-54 0~255
Sockets active F-57 0 = Disable, 1 = Enable
Web Server active F-59 0 = Disable, 1 = Enable
Web password active F-60 0 = Disable, 1 = Enable
26
GETTING STARTED
Web setting password F-61 0000~9999

System Settings
0 = Disable
Factory Set Value F-88
1 = Return to factory settings
0, 1 = PSW version
2, 3 = PSW build year
4, 5 = PSW build month/day
6, 7 = Keyboard CPLD version
8, 9 = Analog-Control CPLD version
A, B = Reserved
Show Version F-89 C, D = Kernel build year
E, F = Kernel build month/day
G, H = Test command version
I, J = Test command build year
K, L = Test command build
month/day
M, N = USB Driver version.
Power On Configuration Settings*
0 = Panel control (local)
1 = External voltage control
2 = External resistance control
F-90
CV Control (Ext-R 10kΩ = Vo, max)
(Ext-R 10kΩ = 0)
0 = Panel control (local)
1 = External voltage control
CC Control F-91
(Ext-R 10kΩ = Io,max)
(Ext-R 10kΩ = 0)
0 = OFF at startup
1 = ON at startup
Power-ON Output F-92
T001 ~ T010 = Run test script TXX at
start up
0 = Master/Local
1 = Master/Parallel1
2 = Master/Parallel2
Master/Slave F-93
3 = Slave/Parallel
4 = Slave/Series (Only 30V, 40V, 80V,
160V models)
27
External Out Logic F-94 0 = High ON, 1 = Low ON

Power Switch trip F-95 0 = Enable , 1 = Disable
Calibration Settings*
Calibration F-00 0000 ~ 9999
Power On and Calibration settings can only be set

*Note during power up.
28
REMOTE CONTROL
REMOTE CONTROL
This chapter describes basic configuration of
IEEE488.2 based remote control. For a command
list, refer to the programming manual,
downloadable from GW Instek website,
www.gwinstek.com
Interface Configuration .............................................. 30

USB Remote Interface........................................................................... 30
Configure GPIB Interface .................................................................... 30
Configure Ethernet Connection .......................................................... 32
Web Server Configuration .......................................................... 32
Sockets Server Configuration ..................................................... 33
USB Remote Control Function Check ............................................... 34
Using Realterm to Establish a Remote Connection ......................... 35
Web Server Remote Control Function Check .................................. 38
Socket Server Function Check ............................................................. 38
Socket Server Examples ............................................. 44
Visual Basic Example ............................................................................. 44
C++ Example ......................................................................................... 45
LabVIEW Example ............................................................................... 47
Command Syntax ....................................................... 48
Command List ........................................................... 52
Status Register Overview ..........................................101
Introduction to the Status Registers.................................................. 101
The Status Registers ............................................................................. 102
Questionable Status Register Group ................................................. 103
Operation Status Register Group ...................................................... 105
Standard Event Status Register Group ............................................. 107
Status Byte Register & Service Request Enable Register .............. 109
Error List ..................................................................111
Command Errors ................................................................................. 111
Execution Errors .................................................................................. 115
Device Specific Errors ......................................................................... 117
Query Errors ......................................................................................... 118
29
Interface Configuration
USB Remote Interface
USB PC side connector Type A, host

configuration
PSW side Rear panel Type B, slave
connector
Speed 1.1/2.0 (full speed/high speed)
USB Class CDC (communications device
class)
Panel operation 1. Connect the USB cable to the rear

panel USB B port.
2. Press the Function key to enter the Page 21

Normal configuration settings.
Set the following USB settings:

Set the rear panel USB port to
F-22 = 2
USB-CDC.
Configure GPIB Interface

To use GPIB, the optional GPIB to USB (GUG-001) adapter must be
used. The GPIB to USB adapter must be connected before the PSW
is turned on. Only one GPIB address can be used at a time.
Configure GPIB 1. Ensure the PSW is off before proceeding.
2. Connect the USB cable from the rear panel

USB B port on the PSW to the USB A port on
the GPIB to USB adapter.
30
REMOTE CONTROL
3. Connect a GPIB cable from a GPIB controller to

the GPIB port on the adapter.
Type A plug From

computer
Type B plug for

PSW series
GUG-001
4. Turn the PSW on.

Set the following GPIB settings:
F-22 = 1 Set the real panel USB port to USB Host.
F-23 = 0~30 Set the GPIB address (0~30)
GPIB constraints  Maximum 15 devices altogether, 20m cable

length, 2m between each device
 Unique address assigned to each device
 At least 2/3 of the devices turned On
 No loop or parallel connection
31
Configure Ethernet Connection

The Ethernet interface can be configured for a number of different
applications. Ethernet can be configured for basic remote control or
monitoring using a web server or it can be configured as a socket
server.
The PSW series supports both DHCP connections so the instrument
can be automatically connected to an existing network or
alternatively, network settings can be manually configured.
Ethernet For details on how to configure the Ethernet

configuration settings, please see the configuration table on
Parameters page 24.
MAC Address LAN
(display only)
DHCP IP Address
Subnet Mask Gateway
DNS Address Sockets Active
Web Server Active Web Password Active
Web set password 0000~9999 (default 0000)
Web Server Configuration
Configuration This configuration example will configure the

PSW as a web server and use DHCP to
automatically assign an IP address to the PSW.
LAN
1. Connect an Ethernet cable from the
network to the rear panel Ethernet
port.
32
REMOTE CONTROL

Set the following LAN settings:
F-36 = 1 Enable LAN

F-37 = 1 Turn DHCP to enable
F-59 = 1 Turn the web server on
It may be necessary to cycle the power or refresh the

Note web browser to connect to a network.
Sockets Server Configuration
Configuration This configuration example will configure the

PSW sockets server.
The following configuration settings will

manually assign the PSW an IP address and
enable the socket server. By default, the socket
server port number is 2268 and cannot be
configured.
LAN
1. Connect an Ethernet cable from the
network to the rear panel Ethernet
port.

3. Set the following LAN settings:

F-36 = 1 Enable LAN
F-37 = 0 Disable DHCP
F-39 = 172 IP Address part 1 of 4
F-43 = 255 Subnet Mask part 1 of 4
33

F-43 = 172 Gateway part 1 of 4
F-57 = 1 Enable Sockets
The socket function is only available for firmware

Note version V1.12 or above. See the user manual to check
your firmware version number.
USB Remote Control Function Check
Functionality Invoke a terminal application such as

check Realterm. The PSW will appear as a COM port
on the PC.
To check the COM port No, see the Device

Manager in the PC. For WinXP; Control panel
→ System → Hardware tab.
If you are not familiar with using a terminal

Note application to send/receive remote commands via
a USB connection, please page 35(Using Realterm
to Establish a Remote Connection) for more
information.
Run this query command via the terminal after

the instrument has been configured for USB
remote control (page 30).
*idn?
This should return the Manufacturer, Model
number, Serial number, and Firmware version
in the following format.
GW-INSTEK,PSW-XXX-X,TW123456,01.00.20110101
34
REMOTE CONTROL
Manufacturer: GW-INSTEK
Model number : PSW-3036
Serial number : TW123456
Firmware version : 01.00.20110101
Using Realterm to Establish a Remote Connection
Background Realterm is a terminal program that can be

used to communicate with a device attached to
the serial port of a PC or via an emulated serial
port via USB.
The following instructions apply to version

2.0.0.70. Even though Realterm is used as an
example to establish a remote connection, any
terminal program can be used that has similar
functionality.
Realterm can be downloaded on Sourceforge.net

Note free of charge.
For more information please see

http://realterm.sourceforge.net/
Operation 1. Download Realterm and install according to

the instructions on the Realterm website.
2. Connect the PSW via USB (page 30).
3. Go to the Windows device manager and find

the COM port number for the connection.
For example, go to the Start menu > Control
Panel > Device Manager
Double click the Ports icon to reveal the

connected serial port devices and the COM
port for the each connected device.
35
The baud rate, stop bit and parity settings can

be viewed for the virtual COM port by right-
clicking connected device and selecting the
Properties option.
4. Start Realterm on the PC as an administrator.

Click:
Start menu>All Programs>RealTerm>realterm
Tip: to run as an administrator, you can right

click the Realterm icon in the Windows Start
menu and select the Run as Administrator
option.
5. After Realterm has started, click on the Port

tab.
Enter the Baud, Parity, Data bits, Stop bits and

Port number configuration for the connection.
The Hardware Flow Control, Software Flow

Control options can be left at the default
settings.
Press Open to connect to the PSW.
36
REMOTE CONTROL
6. Click on the Send tab.
In the EOL configuration, check on the +CR

and +LF check boxes.
Enter the query:

*idn?
Click on Send ASCII.
37
7. The terminal display will return the following:
GW-INSTEK,PSW-XXX-X,TW123456,01.00.20110101
(manufacturer, model, serial number, version)
8. If Realterm fails to connect to the PSW, please

check all the cables and settings and try again.
Web Server Remote Control Function Check
Functionality Enter the IP address of the power supply in a

check web browser after the instrument has been
configured as a web server (page 32).
http:// XXX.XXX.XXX.XXX
The web browser interface appears.
Socket Server Function Check
Background To test the socket server functionality, National

Instruments Measurement and Automation
Explorer can be used. This program is
available on the NI website, www.ni.com, via a
search for the VISA Run-time Engine page, or
“downloads” at the following URL,
http://www.ni.com/visa/
Requirements Firmware: V1.12

Operating System: Windows XP, 7
Functionality 1. Start the NI Measurement and Automation

check Explorer (MAX) program. Using Windows,
press:
38
REMOTE CONTROL
Start>All Programs>National
Instruments>Measurement & Automation
2. From the Configuration panel access;
My System>Devices and Interfaces>Network

Devices
3. Click Create New... .
4. Select Visa TCP/IP Resource.
3
2
39
5. Select Manual Entry of Raw Socket from the

popup window.
6. Click Next.
7. Enter the IP address and the port number of

the PSW. The port number is fixed at 2268.
8. Click the Validate button. A popup box will

appear when successful.
9. Click Next.
40
REMOTE CONTROL
7
8
10. Next configure the Alias (name) of the PSW

connection. In this example the Alias is:
PSW_DC1
11. Click finish.
10
11
12. The IP address of the PSW will now appear

under Network Devices in the configuration
panel. Select this icon now.
13. Press Open VISA Test Panel.
41
13
12
14. Click Configuration icon.
15. In the I/O Settings tab, select the Enable

Termination Character check box. Ensure Line
Feed - \n is selected as the line feed character.
16. Click Apply Changes.
14
15
16
17. Click the Input/Output icon.
18. Ensure *IDN?\n is selected in the Select or

Enter Command dropdown text box.
19. Click the Query button.
20. The *IDN? query should be returned to the

buffer area:
GW-INSTEK,PSW250-9,,01.54.20140313\n
42
REMOTE CONTROL
17
18 19
20
For further details, please see the following

Note programming examples.
43
Socket Server Examples
Visual Basic Example
Background The following visual basic programming example

uses the VISA COM 3.0 Type Library. The
example will connect to the PSW using the IP
address of 172.15.5.133 over port 2268. The
program will send the *IDN? to the PSW, print the
return string and then close the connection.
44
REMOTE CONTROL
C++ Example
Background The following program creates a connection to the

PSW and sets the voltage to 3.3 volts and the
current 1.5 amps. The voltage and current reading
is then read back and the connection is closed.
Add visa32.lib to the project library when building the

Note following sample program.
45
46
REMOTE CONTROL
LabVIEW Example
Background The following picture shows a LabView

programming example for the PSW.
47
Command Syntax
IEEE488.2 Partial compatibility
Compatible
Standard SCPI, 1999 Partial compatibility
Command SCPI commands follow a tree-like structure,

Structure organized into nodes. Each level of the
command tree is a node. Each keyword in a
SCPI command represents each node in the
command tree. Each keyword (node) of a SCPI
command is separated by a colon (:).
For example, the diagram below shows an

SCPI sub-structure and a command example.
MEASure MEASure:SCALar:CURRent:DC?
SCALar
VOLTage CURRent POWer
DC DC DC
Command types There are a number of different instrument

commands and queries. A command sends
instructions or data to the unit and a query
receives data or status information from the
unit.
Command types
Simple A single command

with/without a parameter
Example *IDN?
48
REMOTE CONTROL
Query A query is a simple or

compound command
followed by a question mark
(?). A parameter (data) is
returned.
Example meas:curr:dc?
Compound Two or more commands on

the same command line.
Compound commands are
separated with either a semi-
colon (;) or a semi-colon and a
colon (;:).
A semi-colon is used to join

two related commands, with
the caveat that the last
command must begin at the
last node of the first
command.
A semi-colon and colon are

used to combine two
commands from different
nodes.
Example meas:volt:dc?;:meas:curr:dc?
Command Forms Commands and queries have two different

forms, long and short. The command syntax is
written with the short form of the command in
capitals and the remainder (long form) in
lower case.
The commands can be written in capitals or

lower-case, just so long as the short or long
forms are complete. An incomplete command
49
will not be recognized.
Below are examples of correctly written

commands.
Long form STATus:OPERation:NTRansition?
STATUS:OPERATION:NTRANSITION?
status:operation:ntransition?
Short form STAT:OPER:NTR?
stat:oper:ntr?
Square Brackets Commands that contain square brackets

indicate that the contents are optional. The
function of the command is the same with or
without the square bracketed items, as shown
below.
Both “DISPlay:MENU[:NAME]?” and

“DISPlay:MENU?” are both valid forms.
Command APPLY 1.5,5.2 1. Command header

Format 2. Space
3. Parameter 1
1 2 34 5
4. Comma (no space
before/after
comma)
5. Parameter 2
Parameters Type Description Example

<Boolean> Boolean logic 0, 1
<NR1> integers 0, 1, 2, 3
<NR2> decimal numbers 0.1, 3.14, 8.5
<NR3> floating point 4.5e-1, 8.25e+1
<NRf> any of NR1, 2, 3 1, 1.5, 4.5e-1
50
REMOTE CONTROL
<block data> Definitive length arbitrary block

data. A single decimal digit
followed by data. The decimal
digit specifies how many 8-bit
data bytes follow.
Message
LF Line feed code
Terminator
51
Command List
Abort Command ABORt .................................................................................... 55
Apply Command APPLy ..................................................................................... 56
Display DISPlay:MENU[:NAME] ................................................... 57

Commands DISPlay[:WINDow]:TEXT:CLEar ................................... 57
DISPlay[:WINDow]:TEXT[:DATA] ................................ 58
DISPlay:BLINk ..................................................................... 58
Initiate INITiate[:IMMediate]:NAME ............................................ 60

Command
Measure MEASure[:SCALar]:ALL[:DC] ........................................... 61

Commands MEASure[:SCALar]:CURRent[:DC].................................. 61
MEASure[:SCALar]:VOLTage[:DC] ................................. 61
MEASure[:SCALar]:POWer[:DC] ..................................... 62
Output OUTPut:DELay:ON ............................................................ 63

Commands OUTPut:DELay:OFF .......................................................... 63
OUTPut:MODE ................................................................... 64
OUTPut[:STATe][:IMMediate] .......................................... 64
OUTPut[:STATe]:TRIGgered ............................................ 65
OUTPut:PROTection:CLEar ............................................. 65
OUTPut:PROTection:TRIPped ......................................... 65
Sense Command SENSe:AVERage:COUNt .................................................. 66
Status STATus:OPERation[:EVENt] ........................................... 67

Commands STATus:OPERation:CONDition ...................................... 67
STATus:OPERation:ENABle ............................................ 67
STATus:OPERation:PTRansition ..................................... 68
STATus:OPERation:NTRansition..................................... 68
STATus:QUEStionable[:EVENt] ...................................... 68
STATus:QUEStionable:CONDition ................................. 69
52
REMOTE CONTROL
STATus:QUEStionable:ENABle ........................................ 69
STATus:QUEStionable:PTRansition ................................. 69
STATus:QUEStionable:NTRansition ................................ 69
STATus:PRESet ..................................................................... 70
Source [SOURce:]CURRent[:LEVel][:IMMediate]
Commands [:AMPLitude] .......................................................................... 71
[SOURce:]CURRent[:LEVel]:TRIGgered[:AMPLitude] 72
[SOURce:]CURRent:PROTection[:LEVel] ....................... 72
[SOURce:]CURRent:PROTection:STATe ........................ 73
[SOURce:]CURRent:SLEW:RISing .................................... 73
[SOURce:]CURRent:SLEW:FALLing ............................... 74
[SOURce:]RESistance[:LEVel][:IMMediate]
[:AMPLitude] .......................................................................... 75
[SOURce:]VOLTage[:LEVel][:IMMediate]
[:AMPLitude] .......................................................................... 76
[SOURce:]VOLTage[:LEVel]:TRIGgered[:AMPLitude] 76
[SOURce:]VOLTage:PROTection[:LEVel] ...................... 77
[SOURce:]VOLTage:SLEW:RISing ................................... 77
[SOURce:]VOLTage:SLEW:FALLing ............................... 78
Trigger TRIGger:TRANsient[:IMMediate] ..................................... 79

Commands TRIGger:TRANsient:SOURce ............................................ 79
TRIGger:OUTPut[:IMMediate] .......................................... 80
TRIGger:OUTPut:SOURce................................................. 80
Trigger Command Examples ............................................... 80
System SYSTem:BEEPer[:IMMediate] ............................................ 83

Commands SYSTem:CONFigure:BEEPer[:STATe] ............................ 83
SYSTem:CONFigure:BLEeder[:STATe] ........................... 84
SYSTem:CONFigure:BTRip[:IMMediate] ........................ 84
SYSTem:CONFigure:BTRip:PROTection........................ 85
SYSTem:CONFigure:CURRent:CONTrol ....................... 85
SYSTem:CONFigure:VOLTage:CONTrol ...................... 86
SYSTem:CONFigure:MSLave ............................................. 86
SYSTem:CONFigure:OUTPut:EXTernal[:MODE] ....... 87
SYSTem:CONFigure:OUTPut:PON[:STATe] ................ 87
SYSTem:COMMunicate:ENABle ...................................... 88
SYSTem:COMMunicate:GPIB[:SELF]:ADDRess .......... 89
SYSTem:COMMunicate:LAN:IPADdress........................ 89
SYSTem:COMMunicate:LAN:GATEway ........................ 90
SYSTem:COMMunicate:LAN:SMASk .............................. 90
53
SYSTem:COMMunicate:LAN:MAC ................................. 90
SYSTem:COMMunicate:LAN:DHCP .............................. 91
SYSTem:COMMunicate:LAN:DNS.................................. 91
SYSTem:COMMunicate:LAN:HOSTname ..................... 91
SYSTem:COMMunicate:LAN:WEB:PACTive ............... 92
SYSTem:COMMunicate:LAN:WEB:PASSword ............ 92
SYSTem:COMMunicate:RLSTate ..................................... 93
SYSTem:COMMunicate:USB:FRONt:STATe ................ 93
SYSTem:COMMunicate:USB:REAR:STATe .................. 94
SYSTem:COMMunicate:USB:REAR:MODE ................. 94
SYSTem:ERRor ..................................................................... 94
SYSTem:KEYLock:MODE................................................ 95
SYSTem:KLOCk................................................................... 95
SYSTem:INFormation ......................................................... 95
SYSTem:PRESet ................................................................... 96
SYSTem:VERSion ................................................................ 96
Common *CLS ........................................................................................ 97

Commands *ESE ........................................................................................ 97
*ESR ........................................................................................ 98
*IDN ....................................................................................... 98
*OPC ....................................................................................... 98
*RST ........................................................................................ 99
*SRE ........................................................................................ 99
*STB ........................................................................................ 99
*TRG ..................................................................................... 100
*TST ...................................................................................... 100
*WAI ..................................................................................... 100
54
REMOTE CONTROL
Abort Command
ABORt ..................................................................................... 55
ABORt Set
Description The ABORt command will cancel any triggered

actions.
Syntax ABORt
55
APPLy Command
APPLy ......................................................................................56
Set
APPLy Query
Description The APPLy command is used to set both the

voltage and current. The voltage and current will
be output as soon as the function is executed if the
programmed values are within the accepted
range. An execution error will occur if the
programmed values are not within accepted
ranges.
The Apply command will set the voltage/current
values but these values will not be reflected on the
display until the Output is On or if the
DISPlay:MENU:NAME 3 (set menu) command is
used.
Syntax APPLy {<voltage>|MIN|MAX}[,{<current>|MIN|MAX}]
Query Syntax APPLy?
Parameter <voltage> <NRf> 0% ~ 105% of the rated output
voltage.
<current> <NRf> 0% ~ 105% of the rated output
current.
MIN 0 volts/0 amps
MAX Maxium value for the present range.
Return parameter <NRf> Returns the voltage and current.
Example APPL 5.05,1.1
Sets the voltage and current to 5.05V and 1.1A.
Query Example APPL?
+5.050, +1.100
Returns voltage (5.05V) and current (1.1A) setting.
56
REMOTE CONTROL
Display Commands
DISPlay:MENU[:NAME] .................................................... 57
DISPlay[:WINDow]:TEXT:CLEar .................................... 57
DISPlay[:WINDow]:TEXT[:DATA] ................................. 58
DISPlay:BLINk ...................................................................... 58
Set
DISPlay:MENU[:NAME] Query
Description The DISPlay MENU command selects a screen

menu or queries the current screen menu.
Syntax DISPlay:MENU[:NAME] <NR1>
Query Sytax DISPlay:MENU[:NAME]?
Parameter/ <NR1> Description
Return parameter
0 Measurement-Voltage / Measurement-
Current
1 Measurement-Voltage / Measurement-
Power
2 Measurement-Power / Measurement-
Current
3 Set Menu
4 OVP / OCP Menu
5~99 Not Used.
100~199 F-00~99 Menu.
Example DISP:MENU:NAME 0
Sets the display to the Voltage/Current display
screen.
DISPlay[:WINDow]:TEXT:CLEar Set
Description Clears the text on the main screen from the

DISPlay[:WINDow]:TEXT[:DATA] command.
57
Syntax DISPlay[:WINDow]:TEXT:CLEar
Set
DISPlay[:WINDow]:TEXT[:DATA] Query
Description Sets or queries the data text that will be written to

the display. Writing to the display will overwrite
data that is currently on the screen. Overwriting a
display area with a shorter string may or may not
overwrite the screen. The string must be enclosed
in quotes: “STRING”. Only ASCII characters 20H
to 7EH can be used in the <string>.
Syntax DISPlay[:WINDow]:TEXT[:DATA] <string>
Query Syntax DISPlay[:WINDow]:TEXT[:DATA]?
Parameter/ <string> ASCII character 20H to 7EH can be used
Return parameter to in the string parameter. The string
must be enclosed in quotes: “STRING”
Example DISP:WIND:TEXT:DATA “STRING”
Writes STRING to the display.
Query Example DISP:WIND:TEXT:DATA?
“STRING”
Returns the text data string on the screen.
Set
DISPlay:BLINk Query
Description Turns blink on or off for the display.

Syntax DISPlay:BLINk { 0 | 1 | OFF | ON }
Query Syntax DISPlay:BLINk?
Parameter 0 <NR1>Turns blink OFF
OFF Turns blink OFF
1 <NR1> Turns blink ON
ON Turns blink ON
58
REMOTE CONTROL
Return parameter 0 <NR1>Turns blink OFF

1 <NR1>Turns blink ON
Example DISP:BLIN 1
Turns blink ON.
59
Initiate Command
INITiate[:IMMediate]:NAME .............................................60
INITiate[:IMMediate]:NAME Set
Description The INITiate command starts the TRANsient or

OUTPut trigger.
See the trigger commands on page 79 for usage
details.
Syntax INITiate[:IMMediate]:NAME {TRANsient|OUTPut}
Parameter TRANSient Starts the TRANsient trigger.
OUTPut Starts the OUTPut trigger.
Example INITiate:NAME TRANient
Starts the TRANSient trigger.
60
REMOTE CONTROL
Measure Commands
MEASure[:SCALar]:ALL[:DC]............................................ 61
MEASure[:SCALar]:CURRent[:DC] .................................. 61
MEASure[:SCALar]:VOLTage[:DC] .................................. 61
MEASure[:SCALar]:POWer[:DC] ...................................... 62
MEASure[:SCALar]:ALL[:DC] Query
Description Takes a measurement and returns the average

output current and voltage
Syntax :MEASure[:SCALar]:ALL[:DC]?
Return parameter "+0.0000,+0.0000" <voltage>,<current>
Returns the voltage (V) and
current (A), respectively.
MEASure[:SCALar]:CURRent[:DC] Query

output current
Syntax MEASure[:SCALar]:CURRent[:DC]?
Return parameter <NRf> Returns the current in amps.
MEASure[:SCALar]:VOLTage[:DC] Query

output voltage.
Syntax MEASure[:SCALar]:VOLTage[:DC]?
Return <NRf> Returns the voltage in volts.
61
MEASure[:SCALar]:POWer[:DC] Query

output power.
Syntax MEASure[:SCALar]:POWer[:DC]?
Return <NRf> Returns the power measured in watts.
62
REMOTE CONTROL
Output Commands
OUTPut:DELay:ON ............................................................. 63
OUTPut:DELay:OFF ........................................................... 63
OUTPut:MODE .................................................................... 64
OUTPut[:STATe][:IMMediate] ........................................... 64
OUTPut[:STATe]:TRIGgered ............................................. 65
OUTPut:PROTection:CLEar .............................................. 65
OUTPut:PROTection:TRIPped ......................................... 65
Set
OUTPut:DELay:ON Query
Description Sets the Delay Time in seconds for turning the

output on. The delay is set to 0.00 by default.
Syntax OUTPut:DELay:ON <NRf>
Query Syntax OUTPut:DELay:ON?
Parameter <NRf> 0.00~99.99 seconds, where 0=no delay.
Return parameter <NRf> Returns the delay on time in seconds
until the output is turned on.
Set
OUTPut:DELay:OFF Query
Description Sets the Delay Time in seconds for turning the

output off. The delay is set to 0.00 by default.
Syntax OUTPut:DELay:OFF <NRf>
Return Syntax OUTPut:DELay:OFF?
Parameter <NRf> 0.00~99.99 seconds, where 0=no delay.
Return parameter <NRf> Returns the delay off time in seconds
until the output is turned off.
63
Set
OUTPut:MODE Query
Description Sets the PSW output mode. This is the equivalent

to the F-03 (V-I Mode Slew Rate Select) settings.
Syntax OUTPut:MODE {<NR1>|CVHS|CCHS|CVLS|CCLS}
Return Syntax OUTPut:MODE?
Parameter 0 CV high speed priority
CVHS CV high speed priority
1 CC high speed priority
CCHS CC high speed priority
2 CV slew rate priority
CVLS CV slew rate priority
3 CC slew rate priority
CCLS CC slew rate priority
Return parameter <NR1> Returns the output mode.
Set
OUTPut[:STATe][:IMMediate] Query
Description Turns the output on or off.

Syntax OUTPut[:STATe][:IMMediate] { OFF | ON | 0 | 1 }
Query Syntax OUTPut[:STATe][:IMMediate]?
Parameter 0 <NR1> Turns the output off.
OFF Turns the output off.
1 <NR1> Turns the output on.
ON Turns the output on.
Return parameter <NR1> Returns output status of the instrument.
64
REMOTE CONTROL
Set
OUTPut[:STATe]:TRIGgered Query
Description Turns the output on or off when a software trigger

is generated.
Syntax OUTPut[:STATe]:TRIGgered { OFF | ON | 0 | 1 }
Query Syntax OUTPut[:STATe]:TRIGgered?
Parameter 0 <NR1>Turns the output off when a
software trigger is generated.
OFF Turns the output off when a software
trigger is generated.
1 <NR1>Turns the output on when a
software trigger is generated.
ON Turns the output on when a software
Return parameter <NR1> Returns output trigger status of the
instrument.
OUTPut:PROTection:CLEar Set
Description Clears over-voltage, over-current and over-

temperature (OVP, OCP, OTP) protection circuits.
It also clears the shutdown protection circuit. The
AC failure protection cannot be cleared.
Syntax OUTPut:PROTection:CLEar
OUTPut:PROTection:TRIPped Query
Description Returns the state of the protection circuits (OVP,

OCP, OTP).
Query Syntax OUTPut:PROTection:TRIPped?
Return parameter 0 <NR1>Protection circuits are not
tripped.
1 <NR1>Protection circuits are tripped.
65
Sense Command
SENSe:AVERage:COUNt ...................................................66
Set
SENSe:AVERage:COUNt Query
Description Determines the level of smoothing for the average

setting. This is the equivalent to the F-17 function
setting.
Syntax SENSe:AVERage:COUNt {<NR1>| LOW | MIDDle |
HIGH}
Query Syntax SENSe:AVERage:COUNt?
Parameter 0 | LOW Low level of smoothing.
1 | MIDDle Middle level of smoothing.
2 | HIGH High level of smoothing.
Return parameter <NR1> Returns the level of smoothing.
0 Low level of smoothing.
1 Middle level of smoothing.
2 High level of smoothing.
Example SENSe:AVERage:COUNt 1
Sets the level of smoothing to middle.
66
REMOTE CONTROL
Status Commands
STATus:OPERation[:EVENt] ............................................ 67
STATus:OPERation:CONDition ....................................... 67
STATus:OPERation:ENABle ............................................. 67
STATus:OPERation:PTRansition ...................................... 68
STATus:OPERation:NTRansition ..................................... 68
STATus:QUEStionable[:EVENt] ....................................... 68
STATus:QUEStionable:CONDition.................................. 69
STATus:QUEStionable:ENABle ........................................ 69
STATus:QUEStionable:PTRansition ................................. 69
STATus:QUEStionable:NTRansition ................................ 69
STATus:PRESet ..................................................................... 70
STATus:OPERation[:EVENt] Query
Description Queries the Operation Status Event register and

clears the contents of the register.
Syntax STATus:OPERation[:EVENt]?
Return <NR1> Returns the bit sum of the Operation
Status Event register.
STATus:OPERation:CONDition Query
Description Queries the Operation Status register. This query

will not clear the register.
Syntax STATus:OPERation:CONDition?
Return <NR1> Returns the bit sum of the Operation
Condition register.
Set
STATus:OPERation:ENABle Query
Description Sets or queries the bit sum of the Operation Status

Enable register.
67
Syntax STATus:OPERation:ENABle <NRf>

Query Syntax STATus:OPERation:ENABle?
Parameter <NRf> 0 ~ 32767
Return parameter <NR1> 0 ~ 32767
Set
STATus:OPERation:PTRansition Query
Description Sets or queries the bit sum of the positive

transition filter of the Operation Status register.
Syntax STATus:OPERation:PTRansition <NRf>
STATus:OPERation:PTRansition?
Set
STATus:OPERation:NTRansition Query
Description Sets or queries the bit sum of the negative

transition filter of the Operation Status register.
Syntax STATus:OPERation:NTRansition <NRf>
Query Syntax STATus:OPERation:NTRansition?
STATus:QUEStionable[:EVENt] Query
Description Queries the bit sum of the Questionable Status

Event register. This query will also clear the
contents of the register.
Query Syntax STATus:QUEStionable[:EVENt]?
68
REMOTE CONTROL
STATus:QUEStionable:CONDition Query
Description Queries the status (bit sum) of the Questionable

Status register. This query will not clear the
register.
Query Syntax STATus:QUEStionable:CONDition?
Set
STATus:QUEStionable:ENABle Query
Description Sets or queries the bit sum of the Questionable

Status Enable register.
Syntax STATus:QUEStionable:ENABle <NRf>
Query Syntax STATus:QUEStionable:ENABle?
Set
STATus:QUEStionable:PTRansition Query
Description Sets or queries the bit sum of the positive

transition filter of the Questionable Status register.
Syntax STATus:QUEStionable:PTRansition <NRf>
Return Syntax STATus:QUEStionable:PTRansition?
Set
STATus:QUEStionable:NTRansition Query
Description Sets or queries the negative transition filter of the

Questionable Status register.
69
Syntax STATus:QUEStionable:NTRansition <NRf>

Query Syntax STATus:QUEStionable:NTRansition?
STATus:PRESet Set
Description This command resets the ENABle register, the

PTRansistion filter and NTRansistion filter on the
Operation Status and Questionable Status
Registers. The registers/filters will be reset to a
default value.
Default Register/Filter Values Setting
QUEStionable Status Enable 0x0000
QUEStionable Status Positive Transition 0x7FFF
QUEStionable Status Negative Transition 0x0000
Operation Status Enable 0x0000
Operation Status Positive Transition 0x7FFF
Operation Status Negative Transition 0x0000
Summary: The Questionable Status Enable
registers and the Operation Status Enable registers
are both reset to 0.
The Questionable Status and Operation Status
Positive Transition filters are all set high (0x7FFF)
and the Negative Transition filters are all set low
(0x0000). I.e., only positive transitions will be
recognized for the Questionable Status and
Operation Status registers.
Syntax STATus:PRESet
70
REMOTE CONTROL
Source Commands
[SOURce:]CURRent[:LEVel][:IMMediate]
[:AMPLitude] .......................................................................... 71
[SOURce:]CURRent[:LEVel]:TRIGgered[:AMPLitude] 72
[SOURce:]CURRent:PROTection[:LEVel] ....................... 72
[SOURce:]CURRent:PROTection:STATe ........................ 73
[SOURce:]CURRent:SLEW:RISing .................................... 73
[SOURce:]CURRent:SLEW:FALLing ............................... 74
[SOURce:]RESistance[:LEVel][:IMMediate]
[:AMPLitude] .......................................................................... 75
[SOURce:]VOLTage[:LEVel][:IMMediate]
[:AMPLitude] .......................................................................... 76
[SOURce:]VOLTage[:LEVel]:TRIGgered[:AMPLitude] 76
[SOURce:]VOLTage:PROTection[:LEVel] ...................... 77
[SOURce:]VOLTage:SLEW:RISing ................................... 77
[SOURce:]VOLTage:SLEW:FALLing ............................... 78
[SOURce:]CURRent[:LEVel][:IMMediate] Set
[:AMPLitude] Query
Description Sets or queries the current level in amps. For

externally set current levels (from the analog
control connector) the set current level is returned.
Syntax [SOURce:]CURRent[:LEVel][:IMMediate][:AMPLitude]
{<NRf>|MIN|MAX}
Query Syntax [SOURce:]CURRent[:LEVel][:IMMediate][:AMPLitude]?
[MIN|MAX]
Parameter/Return <NRf> 0~105% of the rated current output level.
MIN Minimum current level.
MAX Maximum current level.
Example SOUR:CURR:LEV:IMM:AMPL? MAX
37.800
Returns the maximum possible current level in
amps.
71
[SOURce:]CURRent[:LEVel]:TRIGgered Set
[:AMPLitude] Query
Description Sets or queries the current level in amps when a

software trigger has been generated.
Syntax [SOURce:]CURRent[:LEVel]:TRIGgered[:AMPLitude]
{<NRf>|MIN|MAX}
Query Syntax [SOURce:]CURRent[:LEVel]:TRIGgered[:AMPLitude]?
[MIN|MAX]
Parameter/Return <NRf> 0%~105% of the rated current output in
amps.
Example SOUR:CURR:LEV:TRIG:AMPL? MAX
37.800
Returns the maximum possible current level in
amps.
Set
[SOURce:]CURRent:PROTection[:LEVel] Query
Description Sets or queries the OCP (over-current protection)

level in amps.
Syntax [SOURce:]CURRent:PROTection[:LEVel]
{<NRf>|MIN|MAX}
Query Syntax [SOURce:]CURRent:PROTection[:LEVel]? [MIN|MAX]
Parameter/Return <NRf> OCP range in Amps.
Example SOUR:CURR:PROT:LEV? MIN
+3.600
Returns the minimum possible current level in
amps.
72
REMOTE CONTROL
Set
[SOURce:]CURRent:PROTection:STATe Query
Description Turns OCP (over-current protection) on or off.

Syntax [SOURce:]CURRent:PROTection:STATe {0|1|OFF|ON}
Query Syntax [SOURce:]CURRent:PROTection:STATe?
Parameter/Return 0 <NR1> Turns the buzzer off.
OFF Turns the OCP off.
1 <NR1> Turns the OCP on.
ON Turns the OCP on.
Return parameter <Bool> Returns the protection status (0 or 1).
Example SOUR:CURR:PROT:STAT OFF
Turns OCP off.
Set
[SOURce:]CURRent:SLEW:RISing Query
Description Sets or queries the rising current slew rate. This is

only applicable for CC slew rate priority mode.
Syntax [SOURce:]CURRent:SLEW:RISing {<NRf>|MIN|MAX}
Query Syntax [SOURce:]CURRent:SLEW:RISing? [MIN|MAX]
Parameter/Return <NRf> 0.01A/s ~ 72.00A/s (PSW 30-36)
0.1A/s ~ 144.0A/s (PSW 30-72)
0.1A/s ~ 216.0A/s (PSW 30-108)
0.01A/s ~ 54.00A/s (PSW 40-27)
0.1A/s ~ 108.0A/s (PSW 40-54)
0.1A/s ~ 162.0A/s (PSW 40-81)
0.01A/s ~ 27.00A/s (PSW 80-13.5)
0.01A/s ~ 54.00A/s (PSW 80-27)
0.01A/s ~ 81.00A/s (PSW 80-40.5)
0.01A/s ~ 14.40A/s (PSW 160-7.2)
0.01A/s ~28.80A/s (PSW 160-14.4)
0.01A/s ~ 43.20A/s (PSW 160-21.6)
0.001A/s ~ 9.000A/s (PSW 250-4.5)
0.01A/s ~ 18.00A/s (PSW 250-9)
73
0.01A/s ~ 27.00A/s (PSW 250-13.5)

0.001A/s ~ 2.880A/s (PSW 800-1.44)
0.001A/s ~ 5.760A/s (PSW 800-2.88)
0.001A/s ~ 8.640A/s (PSW 800-4.32)
MIN Minimum rising current slew rate.
MAX Maximum rising current slew rate.
Example SOUR:CURR:SLEW:RIS 72
Sets the rising current slew rate to 72A/s.
Set
[SOURce:]CURRent:SLEW:FALLing Query
Description Sets or queries the falling current slew rate. This is

only applicable for CC slew rate priority mode.
Syntax [SOURce:]CURRent:SLEW:FALLing
{<NRf>|MIN|MAX}
Query Syntax [SOURce:]CURRent:SLEW:FALLing? [MIN|MAX]
Parameter/Return NRf 0.01A/s ~ 72.00A/s (PSW 30-36)
0.1A/s ~ 144.0A/s (PSW 30-72)
0.1A/s ~ 216.0A/s (PSW 30-108)
0.01A/s ~ 54.00A/s (PSW 40-27)
0.1A/s ~ 108.0A/s (PSW 40-54)
0.1A/s ~ 162.0A/s (PSW 40-81)
0.01A/s ~ 27.00A/s (PSW 80-13.5)
0.01A/s ~ 54.00A/s (PSW 80-27)
0.01A/s ~ 81.00A/s (PSW 80-40.5)
0.01A/s ~ 14.40A/s (PSW 160-7.2)
0.01A/s ~ 28.80A/s (PSW 160-14.4)
0.01A/s ~ 43.20A/s (PSW 160-21.6)
0.001A/s ~ 9.000A/s (PSW 250-4.5)
0.01A/s ~ 18.00A/s (PSW 250-9)
0.01A/s ~ 27.00A/s (PSW 250-13.5)
0.001A/s ~ 2.880A/s (PSW 800-1.44)
0.001A/s ~ 5.760A/s (PSW 800-2.88)
0.001A/s ~ 8.640A/s (PSW 800-4.32)
MIN Minimum falling current slew rate
74
REMOTE CONTROL
MAX Maximum falling current slew rate

Example SOUR:CURR:SLEW:FALL 1
Sets the falling current slew rate to 1A/s.
[SOURce:]RESistance[:LEVel][:IMMediate] Set
[:AMPLitude] Query
Description Sets or queries the internal resistance in ohms.

Syntax [SOURce:]RESistance[:LEVel][:IMMediate][:AMPLitude
] {<NRf>|MIN|DEF|MAX|?}
Query Syntax [SOURce:]RESistance[:LEVel][:IMMediate][:AMPLitude
]? [MIN|MAX]
Parameter/Return <NRf> Resistance in ohms:
0.000Ω ~ 0.833Ω (PSW 30-36)
0.000Ω ~ 0.417Ω (PSW 30-72)
0.000Ω ~ 0.278Ω (PSW 30-108)
0.000Ω ~ 1.481Ω (PSW 40-27)
0.000Ω ~ 0.741Ω (PSW 40-54)
0.000Ω ~ 0.494Ω (PSW 40-81)
0.000Ω ~ 5.926Ω (PSW 80-13.5)
0.000Ω ~ 2.963Ω (PSW 80-27)
0.000Ω ~ 1.975Ω (PSW 80-40.5)
0.000Ω ~ 22.222Ω (PSW 160-7.2)
0.000Ω ~ 11.111Ω (PSW 160-14.4)
0.000Ω ~ 7.407Ω (PSW 160-21.6)
0.00Ω ~ 55.55Ω (PSW 250-4.5)
0.00Ω ~ 27.77Ω (PSW 250-9)
0.00Ω ~ 18.51Ω (PSW 250-13.5)
0.0Ω ~ 555.5Ω (PSW 800-1.44)
0.0Ω ~ 277.8Ω (PSW 800-2.88)
0.0Ω ~ 185.1Ω (PSW 800-4.32)
MIN Minimum internal resistance in ohms
MAX Maximum internal resistance in ohms
Example SOUR:RES:LEV:IMM:AMPL 0.1
Sets the internal resistance to 100mΩ.
75
[SOURce:]VOLTage[:LEVel][:IMMediate] Set
[:AMPLitude] Query
Description Sets or queries the voltage level in volts.

Syntax [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPLitude]
{<NRf>|MIN|MAX}
Query Syntax [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPLitude]?
[MIN|MAX]
Parameter/Return <NRf> 0~105% of the rated output voltage in
volts.
MIN Minimum voltage level
MAX Maximum voltage level
Example SOUR:VOLT:LEV:IMM:AMPL 10
Sets the voltage level to 10 volts.
[SOURce:]VOLTage[:LEVel]:TRIGgered Set
[:AMPLitude] Query
Description Sets or queries the voltage level in volts when a

software trigger has been generated.
Syntax [SOURce:]VOLTage[:LEVel]:TRIGgered[:AMPLitude]
{<NRf>|MIN|MAX}
Query Syntax [SOURce:]VOLTage[:LEVel]:TRIGgered[:AMPLitude]?

[MIN|MAX]
Parameter/Return <NRf> 0%~105% of the rated voltage output in
volts.
Example SOUR:VOLT:LEV:TRIG:AMPL 10
Sets the voltage level to 10 volts when a software
76
REMOTE CONTROL
Set
[SOURce:]VOLTage:PROTection[:LEVel] Query
Description Sets or queries the overvoltage protection level.

Syntax [SOURce:]VOLTage:PROTection[:LEVel]
{<NRf>|MIN|MAX}
Query Syntax [SOURce:]VOLTage:PROTection[:LEVel]? [MIN|MAX]
Parameter/Return <NRf> OVP range in volts.
MIN Minimum OVP level
MAX Maximum OVP level
Example SOUR:VOLT:PROT:LEV MAX
Sets the OVP level to its maximum.
Set
[SOURce:]VOLTage:SLEW:RISing Query
Description Sets or queries the rising voltage slew rate. This is

only applicable for CV slew rate priority mode.
Syntax [SOURce:]VOLTage:SLEW:RISing {<NRf>|MIN|MAX}
Query Syntax [SOURce:]VOLTage:SLEW:RISing? [MIN|MAX]
Parameter/Return <NRf> 0.01V/s ~ 60.00V/s (PSW 30-XX)
0.01V/s ~ 80.00V/s (PSW 40-XX)
0.1V/s ~ 160.0V/s (PSW 80-XX)
0.1V/s ~ 320.0V/s (PSW 160-XX)
0.1V/s ~ 500.0V/s (PSW 250-XX)
1V/s ~ 1600V/s (PSW 800-XX)
MIN Minimum rising voltage slew rate.
MAX Maximum rising voltage slew rate.
Example SOUR:VOLT:SLEW:RIS MAX
Sets the rising voltage slew rate to its maximum.
77
Set
[SOURce:]VOLTage:SLEW:FALLing Query
Description Sets or queries the falling voltage slew rate. This is

only applicable for CV slew rate priority mode.
Syntax [SOURce:]VOLTage:SLEW:FALLing
{<NRf>|MIN|MAX}
Query Syntax [SOURce:]VOLTage:SLEW:FALLing? [MIN|MAX]
Parameter/Return <NRf> 0.01V/s ~ 60.00V/s (PSW 30-XX)
0.01V/s ~ 80.00V/s (PSW 40-XX)
0.1V/s ~ 160.0V/s (PSW 80-XX)
0.1V/s ~ 320.0V/s (PSW 160-XX)
0.1V/s ~ 500.0V/s (PSW 250-XX)
1V/s ~ 1600V/s (PSW 800-XX)
MIN Minimum voltage falling slew rate.
MAX Maximum voltage falling slew rate.
Example SOUR:VOLT:SLEW:FALL MIN
Sets the falling voltage slew rate to its minimum.
78
REMOTE CONTROL
Trigger Commands
The trigger commands generate and configure software triggers.
TRIGger:TRANsient[:IMMediate] ..................................... 79
TRIGger:TRANsient:SOURce ............................................ 79
TRIGger:OUTPut[:IMMediate] .......................................... 80
TRIGger:OUTPut:SOURce................................................. 80
Trigger Command Examples ............................................... 80
TRIGger:TRANsient[:IMMediate] Set
Query
Description Generates a software trigger for the transient
trigger system. On a trigger, sets the voltage &
current. Refer to the :CURR:TRIG and VOLT:TRIG
commands on page 72 and 76, respectively.
Syntax TRIGger:TRANsient[:IMMediate]
Related [SOURce:]CURRent[:LEVel]:TRIGgered[:AMPLitude]
Commands [SOURce:]VOLTage[:LEVel]:TRIGgered[:AMPLitude]
Set
TRIGger:TRANsient:SOURce Query
Description Sets or queries the trigger source for the transient

system.
Syntax TRIGger:TRANsient:SOURce {BUS | IMMediate}
Query Syntax TRIGger:TRANsient:SOURce?
Parameter/Return BUS Internal software trigger. Waits for
the *TRG (or IEEE 488.1 “get”
group execute trigger) command to
start the trigger.
IMMediate Starts the trigger immediately.
(default)
Example TRIG:TRAN:SOUR BUS
Sets the trigger source as BUS.
79
TRIGger:OUTPut[:IMMediate] Set
Description Generates a software trigger for the output trigger

system. On a trigger, sets the output state. Refer to
the :OUTP:TRIG command on page 65.
Syntax TRIGger:OUTPut[:IMMediate]
Related OUTPut[:STATe]:TRIGgered
commands
Set
TRIGger:OUTPut:SOURce Query
Description Sets or queries the trigger source for the output

system.
Syntax TRIGger:OUTPut:SOURce [BUS | IMMediate]
Query Syntax TRIGger:OUTPut:SOURce?
Parameter/Return BUS Internal software trigger. Waits for
the *TRG (or IEEE 488.1 “get” group
execute trigger) command to start the
trigger.
IMMediate Starts the trigger immediately.
(default)
Example TRIG:OUTP:SOUR BUS
Sets the trigger source of the output system as
BUS.
Trigger Command Examples
1. The transient system for the trigger in immediate mode.

Example 1 TRIG:TRAN:SOUR IMM
CURR:TRIG MAX
VOLT:TRIG 5
80
REMOTE CONTROL
INIT:NAME TRAN <==The current changes to

the maximum, and the
voltage changes to 5V.
2. The transient system for the trigger in BUS mode.

Example 2 TRIG:TRAN:SOUR BUS
CURR:TRIG MAX
VOLT:TRIG 5
INIT:NAME TRAN
TRIG:TRAN (or *TRG) <==The current changes
to the maximum, and the
voltage changes to 5V.
3. The output system for the trigger in immediate mode.

Example 3 TRIG:OUTP:SOUR IMM
OUTP:TRIG 1
INIT:NAME OUTP <==The output changes
to ON.
4. The output system for the trigger in BUS mode.

Example 4 TRIG:OUTP:SOUR BUS
OUTP:TRIG 1
INIT:NAME OUTP
TRIG:OUTP (or *TRG) <==The output changes
to ON.
81
System Function Command

SYSTem:BEEPer[:IMMediate] ............................................83
SYSTem:CONFigure:BEEPer[:STATe] ............................83
SYSTem:CONFigure:BLEeder[:STATe] ...........................84
SYSTem:CONFigure:BTRip[:IMMediate] ........................84
SYSTem:CONFigure:BTRip:PROTection ........................85
SYSTem:CONFigure:CURRent:CONTrol .......................85
SYSTem:CONFigure:VOLTage:CONTrol.......................86
SYSTem:CONFigure:MSLave .............................................86
SYSTem:CONFigure:OUTPut:EXTernal[:MODE] .......87
SYSTem:CONFigure:OUTPut:PON[:STATe] ................87
SYSTem:COMMunicate:ENABle.......................................88
SYSTem:COMMunicate:GPIB[:SELF]:ADDRess ..........89
SYSTem:COMMunicate:LAN:IPADdress ........................89
SYSTem:COMMunicate:LAN:GATEway ........................90
SYSTem:COMMunicate:LAN:SMASk ..............................90
SYSTem:COMMunicate:LAN:MAC ..................................90
SYSTem:COMMunicate:LAN:DHCP ...............................91
SYSTem:COMMunicate:LAN:DNS ..................................91
SYSTem:COMMunicate:LAN:HOSTname ......................91
SYSTem:COMMunicate:LAN:WEB:PACTive ................92
SYSTem:COMMunicate:LAN:WEB:PASSword .............92
SYSTem:COMMunicate:RLSTate ..........................................93
SYSTem:COMMunicate:USB:FRONt:STATe .................93
SYSTem:COMMunicate:USB:REAR:STATe ...................94
SYSTem:COMMunicate:USB:REAR:MODE ..................94
SYSTem:ERRor......................................................................94
SYSTem:KEYLock:MODE.................................................95
SYSTem:KLOCk ...................................................................95
SYSTem:INFormation ..........................................................95
SYSTem:PRESet ....................................................................96
SYSTem:VERSion .................................................................96
82
REMOTE CONTROL
Set
SYSTem:BEEPer[:IMMediate] Query
Description This command causes an audible tone to be

generated by the instrument. The duration time is
specified in seconds.
Syntax SYSTem:BEEPer[:IMMediate]
{<NR1>|MINimum|MAXimum}
Query Syntax SYSTem:BEEPer[:IMMediate]? [MINimum|MAXimum]
Parameter <NR1> 0 ~ 3600 seconds.
MINimum Sets the beeper time to the minimum
(0 seconds)
MAXimum Sets the beeper time to the maximum
(3600 seconds)
Return parameter <NR1> Returns the remaining beeper
duration time in seconds or returns
the maximum or minimum beeper
time in seconds (for the
[MINimum|MAXimum] query
parameters).
Example 1 SYST:BEEP 10
**after a 2 second wait**
SYST:BEEP?
>8
The first command turns the beeper on for 10
seconds. After 2 seconds the SYST:BEEP? query
returns the remaining beeper time (8 seconds).
Example 2 SYST:BEEP? MAX
>3600
Returns the maximum settable beeper time in
seconds.
Set
SYSTem:CONFigure:BEEPer[:STATe] Query
Description Sets or queries the buzzer state on/off.
83
Syntax SYSTem:CONFigure:BEEPer[:STATe] {OFF|ON|0|1}

Query Syntax SYSTem:CONFigure:BEEPer[:STATe]?
Parameter 0 <NR1> Turns the buzzer off.
OFF Turns the buzzer off.
1 <NR1> Turns the buzzer on.
ON Turns the buzzer on.
Return parameter <Boolean> Returns the buzzer status.
Set
SYSTem:CONFigure:BLEeder[:STATe] Query
Description Sets or queries the status of the bleeder resistor.

Syntax SYSTem:CONFigure:BLEeder[:STATe]
Query Syntax {OFF|ON|AUTO|0|1|2}
SYSTem:CONFigure:BLEeder[:STATe]?
Parameter 0 <NR1> Turns the bleeder resistor off.
OFF Turns the bleeder resistor off.
1 <NR1> Turns the bleeder resistor on.
ON Turns the bleeder resistor on.
2 <NR1> Turns the AUTO mode on.
AUTO Turns the AUTO mode on.
Return parameter <NR1> Returns bleeder resistor status.
SYSTem:CONFigure:BTRip[:IMMediate] Set
Description Trips the power switch trip (circuit breaker) to

turn the unit off (shut down the power).
Syntax SYSTem:CONFigure:BTRip[:IMMediate]
84
REMOTE CONTROL
Set
SYSTem:CONFigure:BTRip:PROTection Query
Description Enables/Disables the power switch trip (circuit

breaker) when the OVP or OCP protection
settings are tripped. This setting only applies after
power has been reset.
Syntax SYSTem:CONFigure:BTRip:PROTection
{OFF|ON|0|1}
Query Syntax SYSTem:CONFigure:BTRip:PROTection?
Parameter 0 <NR1> Disables the power switch trip
for OVP or OCP.
OFF Disables the power switch trip for OVP
or OCP.
1 <NR1> Enables the power switch trip
for OVP or OCP.
ON Enables the power switch trip for OVP
or OCP.
Return parameter <Boolean> Returns power switch trip setting.
Set
SYSTem:CONFigure:CURRent:CONTrol Query
Description Sets or queries the CC control mode (local control

(panel), external voltage control, external
resistance control). This setting is applied only
after the unit is reset.
Syntax SYSTem:CONFigure:CURRent:CONTrol { 0 | 1 | 2 | 3 }
Query Syntax SYSTem:CONFigure:CURRent:CONTrol?
Parameter/Return <NR1> Description
0 Local (Panel) control
1 External voltage control
2 External resistance control; 10kΩ = Io
max, 0kΩ = Io min.
85
3 External resistance control; 10kΩ = Io

min, 0kΩ = Io max.
Set
SYSTem:CONFigure:VOLTage:CONTrol Query
Description Sets or queries the CV control mode (local control,

external voltage control, external resistance
control). This setting is applied only after the unit
is reset.
Syntax SYSTem:CONFigure:VOLTage:CONTrol { 0 | 1 | 2 | 3 }
Query Syntax SYSTem:CONFigure:VOLTage:CONTrol?
0 Local (Panel) control
1 External voltage control
2 External resistance control; 10kΩ = Vo
max, 0kΩ = Vo min.
3 External resistance control; 10kΩ = Vo
min, 0kΩ = Vo max.
Set
SYSTem:CONFigure:MSLave Query
Description Sets or queries the unit operation mode. This

setting is only applied after the unit has been
reset.
Syntax SYSTem:CONFigure:MSLave { 0 | 1 | 2 | 3 | 4 }
Query Syntax SYSTem:CONFigure:MSLave?
Series mode is only supported for 30V, 40V, 80V and
Note 160V models.
86
REMOTE CONTROL

0 Master/Local
1 Master/Parallel 1 (2 units)
2 Master/Parallel 2 (3 units)
3 Slave/Parallel
4 Slave/Series
Set
SYSTem:CONFigure:OUTPut:EXTernal[:MODE] Query
Description Sets the external logic as active high or active low.

This setting is only applied after the unit has been
reset.
Syntax SYSTem:CONFigure:OUTPut:EXTernal[:MODE]
Query Syntax SYSTem:CONFigure:OUTPut:EXTernal[:MODE]?
Parameter 0 Active high
HIGH Active high
1 Active low
LOW Active low
Return Parameter 0 <boolean>Active high
1 <boolean>Active low
Set
SYSTem:CONFigure:OUTPut:PON[:STATe] Query
Description Sets the unit to turn the output ON/OFF at

power-up. This setting is only applied after the
unit has been reset.
Syntax SYSTem:CONFigure:OUTPut:PON[:STATe]
{OFF|ON|0|1}
Query Syntax SYSTem:CONFigure:OUTPut:PON[:STATe]?
87
Parameter 0 Output off at power up

OFF Output off at power up
1 Output on at power up
ON Output on at power up
Return Parameter 0 Output off at power up
1 Output on at power up
Set
SYSTem:COMMunicate:ENABle Query
Description Enables/Disables LAN, GPIB or USB remote

interfaces as well as remote services (Sockets, Web
Server).
This setting is applied only after the unit is reset.
Syntax SYSTem:COMMunicate:ENABle <mode>,<interface>
Query Syntax SYSTem:COMMunicate:ENABle? <interface>
Parameter <mode>
OFF Turns the selected mode off.
0 Turns the selected mode off.
ON Turns the selected mode on.
1 Turns the selected mode on.
<interface>
GPIB Select GPIB
USB Select USB
LAN Select LAN
SOCKets Select Sockets
WEB Select the web server
Return Parameter 0 The selected mode is off.
1 The selected mode is on.
88
REMOTE CONTROL
Example SYST:COMM:ENAB 1,USB

Turns the USB interface on.
Query Example SYST:COMM:ENAB? USB
1
Queries the USB state, returns 1 (USB is on).
Set
SYSTem:COMMunicate:GPIB[:SELF]:ADDRess Query
Description Sets or queries the GPIB address. This setting is

applied only after the unit is reset.
Syntax SYSTem:COMMunicate:GPIB[:SELF]:ADDRess
Query Syntax <NR1>
SYSTem:COMMunicate:GPIB[:SELF]:ADDRess?
Parameter/Return <NR1> 0~30
Example SYST:COMM:GPIB:SELF:ADDR 15
Sets the GPIB address to 15.
Set
SYSTem:COMMunicate:LAN:IPADdress Query
Description Sets or queries LAN IP address. This setting is

Syntax SYSTem:COMMunicate:LAN:IPADdress <string>
Query Syntax SYSTem:COMMunicate:LAN:IPADdress?
Parameter/Return <string> LAN IP address in string format
( “address”)
Applicable ASCII characters: 20H to 7EH
Example SYST:COMM:LAN:IPAD “172.16.5.111”
Sets the IP address to 172.16.5.111.
89
Set
SYSTem:COMMunicate:LAN:GATEway Query
Description Sets or queries the Gateway address. This setting

is applied only after the unit is reset.
Syntax SYSTem:COMMunicate:LAN:GATEway <string>
Query Syntax SYSTem:COMMunicate:LAN:GATEway?
Parameter/Return <string> Gateway address in string format
(“address”)
Example SYST:COMM:LAN:GATE “172.16.0.254”
Sets the LAN gateway to 172.16.0.254.
Set
SYSTem:COMMunicate:LAN:SMASk Query
Description Sets or queries the LAN subnet mask. This setting

is applied only after the unit is reset.
Syntax SYSTem:COMMunicate:LAN:SMASk <string>
Query Syntax SYSTem:COMMunicate:LAN:SMASk?
Parameter/Return <string> Subnet mask in string format (“mask”)
Example SYST:COMM:LAN:SMASk “255.255.0.0”
Sets the LAN mask to 255.255.0.0.
SYSTem:COMMunicate:LAN:MAC Query
Description Returns the unit MAC address as a string. The

MAC address cannot be changed.
Query Syntax SYSTem:COMMunicate:LAN:MAC?
Return parameter <string> Returns the MAC address in the
following format “FF-FF-FF-FF-FF-FF”
90
REMOTE CONTROL
Example SYST:COMM:LAN:MAC?
02-80-AD-20-31-B1
Returns the MAC address.
Set
SYSTem:COMMunicate:LAN:DHCP Query
Description Turns DHCP on/off. Queries the DHCP status.

This setting is applied only after the unit is reset.
Syntax SYSTem:COMMunicate:LAN:DHCP {OFF| ON | 0 | 1}
Query Syntax SYSTem:COMMunicate:LAN:DHCP?
Parameter 0 DHCP off
OFF DHCP off
1 DHCP on
ON DHCP on
Return parameter 0 <boolean>DHCP off
1 <boolean>DHCP on
Set
SYSTem:COMMunicate:LAN:DNS Query
Description Sets or queries the DNS address. This setting is

Syntax SYSTem:COMMunicate:LAN:DNS <string>
Query Syntax SYSTem:COMMunicate:LAN:DNS?
Parameter/Return <string> DNS in string format ( “mask”)
Example SYST:COMM:LAN:DNS “172.16.1.252”
Sets the DNS to 172.16.1.252.
SYSTem:COMMunicate:LAN:HOSTname Query
Description Queries the host name.
91
Query Syntax SYSTem:COMMunicate:LAN:HOSTname?

Return Parameter <string> Host name in string format
Query Example SYST:COMM:LAN:HOST?
P-160054
Returns the host name (P-160054).
Set
SYSTem:COMMunicate:LAN:WEB:PACTive Query
Description Sets or queries whether the web password is on or

off. This setting is applied only after the unit is
reset.
Syntax SYSTem:COMMunicate:LAN:WEB:PACTive {OFF |
ON | 0 | 1}
Query Syntax SYSTem:COMMunicate:LAN:WEB:PACTive?
Parameter 0 Web password off
OFF Web password off
1 Web password on
ON Web password on
Return parameter 0 <boolean> Web password off
1 <boolean> Web password on
Set
SYSTem:COMMunicate:LAN:WEB:PASSword Query
Description Sets or queries the web password. This setting is

Syntax SYSTem:COMMunicate:LAN:WEB:PASSword <NR1>
Query Syntax SYSTem:COMMunicate:LAN:WEB:PASSword?
Parameter/Return <NR1> 0 ~ 9999
Example SYST:COMM:LAN:WEB:PASS 1234
Set the web password as 1234.
92
REMOTE CONTROL
Set
SYSTem:COMMunicate:RLSTate Query
Description Sets or queries the control state of the instrument.

Note Only applicable for software version 1.60 or
above.
Syntax SYSTem:COMMunicate:RLSTate {LOCal | REMote |
Query Syntax RWLock}
SYSTem:COMMunicate:RLSTate ?
Parameter LOCal Sets the instrument to front panel
control.
REMote Sets the instrument to remote interface
control.
RWLock Disables the front panel keys and only
allows the instrument to be controlled
via the remote interface.
Return parameter LOC The instrument is set to front panel
control.
REM The instrument is set to remote interface
control.
RWL The front panel keys are disabled. The
instrument can only be controlled via the
remote interface.
Example SYST:COMM:RLST: LOC
Sets the instrument to front panel control.
SYSTem:COMMunicate:USB:FRONt:STATe Query
Description Queries the front panel USB-A port state.

Query Syntax SYSTem:COMMunicate:USB:FRONt:STATe?
Return parameter 0 <NR1>Absent
1 <NR1>Mass Storage
93
SYSTem:COMMunicate:USB:REAR:STATe Query
Description Queries the rear panel USB-B port state.

Query Syntax SYSTem:COMMunicate:USB:REAR:STATe?
Return parameter 0 <NR1>Absent
1 <NR1>USB-CDC
2 <NR1>GPIB-USB (GUG-001)
Set
SYSTem:COMMunicate:USB:REAR:MODE Query
Description Sets or queries the rear panel USB-B port mode.

This command is the equivalent to the F-22
configuration setting.
Syntax SYSTem:COMMunicate:USB:REAR:MODE {0|1|2|3}
Query Syntax SYSTem:COMMunicate:USB:REAR:MODE?
Parameter/ 0 Disable
Return parameter
1 USB Host
2 Auto detect speed
3 Full speed only
Example SYST:COMM:USB:REAR:MODE 1
Sets the rear panel USB-B port mode to USB Host.
SYSTem:ERRor Query
Description Queries the error queue. The last error message is

returned. A maximum of 32 errors are stored in
the error queue.
Query Syntax SYSTem:ERRor?
Paramter/Return <NR1>,<string> Returns an error code followed by
an error message as a string. The
string is returned as “string”.
94
REMOTE CONTROL
Example SYSTem:ERRor?
-100, “Command error”
Set
SYSTem:KEYLock:MODE Query
Description Sets or queries the key lock mode. This setting is

the equivalent of the F-19 function setting.
Syntax SYSTem:KEYLock:MODE {0|1}
Query Syntax SYSTem:KEYLock:MODE?
Parameter / 0 Panel lock: allow output off.
Return parameter
1 Panel lock: allow output on/off.
Set
SYSTem:KLOCk Query
Description Enables or disables the front panel key lock.

Syntax SYSTem:KLOCk { OFF | ON | 0 | 1}
Query Syntax SYSTem:KLOCk?
Parameter 0 Panel keys unlocked
OFF Panel keys unlocked
1 Panel keys locked
ON Panel keys locked
Return parameter 0 <boolean>Panel keys unlocked
1 <Boolean>Panel keys locked
SYSTem:INFormation Query
Description Queries the system information. Returns the

machine version, build date, keyboard CPLD
version and analog CPLD version.
Query Syntax SYSTem:INFormation?
Return Parameter <block data> Definite length arbitrary block
response data.
95
Query Example SYST:INF?

#3212MFRS GW-INSTEK,Model PSW80-13.5,SN
TW0123456789,Firmware-Version 01.43.20130424,
Keyboard-CPLD 0x30c,AnalogControl-CPLD
0x421,Kernel-BuiltON 2013-3-22,TEST-Version
01.00,TEST-BuiltON 2011-8-1,MAC 02-80-ad-20-31-b1
Returns the system information as a block data.
SYSTem:PRESet Set
Description Resets all the settings to the factory default

settings. See page 120 for details.
Syntax SYSTem:PRESet
SYSTem:VERSion Query
Description Returns the version of the SCPI specifications that

the unit complies with.
Query Syntax SYSTem:VERSion?
Return <1999.0> Always returns the SCPI version: 1999.0.
96
REMOTE CONTROL
IEEE 488.2 Common Commands

*CLS ......................................................................................... 97
*ESE ......................................................................................... 97
*ESR ......................................................................................... 98
*IDN ........................................................................................ 98
*OPC ........................................................................................ 98
*RST ......................................................................................... 99
*SRE ......................................................................................... 99
*STB ......................................................................................... 99
*TRG ......................................................................................100
*TST .......................................................................................100
*WAI ......................................................................................100
*CLS Set
Description The *CLS command clears the Standard Event

Status, Operation Status and Questionable Status
registers. The corresponding Enable registers in
each of the above registers are not cleared.
If a <NL> newline code immediately precedes a
*CLS command, the Error Que and the MAV bit in
the Status Byte Register is also cleared.
Syntax *CLS
Set
*ESE Query
Description Sets or queries the Standard Event Status Enable

register.
Syntax *ESE <NR1>
Query Syntax *ESE?
Parameter <NR1> 0~255
Return parameter <NR1> Returns the bit sum of the Standard

Event Status Enable register.
97
*ESR Query
Description Queries the Standard Event Status (Event)

register. The Event Status register is cleared after
it is read.
Query Syntax *ESR?
Return parameter <NR1> Returns the bit sum of the Standard
Event Status (Event) register and clears
the register.
*IDN Query
Description Queries the manufacturer, model name, serial

number, and firmware version of the PSW.
Query Syntax *IDN?
Return parameter <string> Returns the instrument identification as
a string in the following format:
GW-INSTEK,PSW-
3036,TW123456,01.00.20110101
Manufacturer: GW-INSTEK
Model number : PSW-3036
Serial number : TW123456
Firmware version : 01.00.20110101
Set
*OPC Query
Description The *OPC command sets the OPC bit (bit0) of the
Standard Event Status Register when all current
commands have been processed.
The *OPC? Query returns 1 when all the
outstanding commands have completed.
98
REMOTE CONTROL
Syntax *OPC
Query Syntax *OPC?
Return parameter 1 Returns 1 when all the outstanding
commands have completed.
*RST Set
Description Performs a device reset. Configures the unit to a

known configuration (default settings). This
known configuration is independent of the usage
history.
Syntax *RST
Set
*SRE Query
Description Sets or queries the Service Request Enable register.

The Service Request Enable register determines
which registers of the Status Byte register are able
to generate service requests.
Syntax *SRE <NR1>
Query Syntax *SRE?
Parameter <NR1> 0~255
Return parameter <NR1> Returns the bit sum of the Service
Request Enable register.
*STB Query
Description Queries the bit sum of the Status Byte register

with MSS (Master summary Status).
Query Syntax *STB?
Return parameter <NR1> Returns the bit sum of the Status Byte
register with the MSS bit (bit 6).
99
*TRG Set
Description The *TRG command is able to generate a “get”

(Group Execute Trigger). If the PSW cannot accept
a trigger at the time of the command, an error
message is generated (-211, “Trigger ignored”).
Syntax *TRG
*TST Query
Description Executes a self test.

Query Syntax *TST?
Return parameter 0 Returns “0” if there are no errors.
<NR1> Returns an error code <NR1> if there is
an error.
*WAI Set
Description Prevents any other commands or queries from

being executed until all outstanding commands
have completed.
Syntax *WAI
100
REMOTE CONTROL
Status Register Overview

To program the PSW power supply effectively,
the Status registers need to be understood. This
chapter explains in detail how the Status registers
are used and how to configure them.
Introduction to the Status Registers
Overview The status registers are used to determine the

status of the power supply. The status registers
maintain the status of the protection conditions,
operation conditions and instrument errors.
The PSW Series have a number of register groups:
 Questionable Status Register Group

 Standard Event Status Register Group
 Operation Status Register Group
 Status Byte Register
 Service Request Enable Register
 Service Request Generation
 Error Queue
 Output Buffer
The next page shows the structure of the Status

registers.
101
The Status Registers
Questionable Status Register

Condition PTR/NTP Event Enable
OV (Over-Voltage) 0 0 0 0
OC (Over-Current) 1 1 1 1
Not Used 2 2 2 2
POW (AC Power Off) 3 3 3 3
Output
OT (Over-Temperature) 4 4 4 4
Buffer
Not Used 5 5 5 5
:
Not Used 6 6 6 6
:
Not Used 7 7 7 7
:
VL (Voltage-Limit) 8 8 8 8
CL (Current-Limit) 9 9 9 9
Not Used 10 10 10 10
Error Que
SD (Shutdown Alarm) 11 11 11 11
:
Power-Limit 12 12 12 12
:
Not Used 13 13 13 13
:
Not Used 14 14 14 14
Not Used 15 15 15 15 Service
Status Request
Byte Enable
Standard Event Status Register
Register
Register
0 0
Event Enable
1 1
OPC (Operation Complete) 0 0
ERR 2 2
RQC (Request Control) 1 1
QUES 3 3
QUE (Query Error) 2 2
MAV 4 4
DDE (Device Dependent Error) 3 3
ESB 5 5
EXE (Execution Error) 4 4
MSS 6 6
CME (Command Error) 5 5
OPER 7 7
URQ (User Request) 6 6
PON (Power On) 7 7
Operation Status Register

CAL (Calibration mode) 0 0 0 0
Not Used 1 1 1 1
Not Used 2 2 2 2
Not Used 3 3 3 3
Not Used 4 4 4 4
WTG (Waiting for Trigger) 5 5 5 5
Not Used 6 6 6 6
Not Used 7 7 7 7
CV (Constant Voltage Mode) 8 8 8 8
Not Used 9 9 9 9
CC (Constant Current Mode) 10 10 10 10
OND (Output ON Delay) 11 11 11 11
OFD (Output OFF Delay) 12 12 12 12
Not Used 13 13 13 13
PR (Program Running) 14 14 14 14
Not Used 15 15 15 15
102
REMOTE CONTROL
Questionable Status Register Group
Overview The Questionable Status Register Group

indicates if any protection modes or limits have
been tripped.

OV 0 0 0 & 0
OC 1 1 1 & 1
Not Used 2 2 2 & 2
POW 3 3 3 & 3
OT 4 4 4 & 4
Not Used 5 5 5 & 5
Not Used 6 6 6 & 6
Not Used 7 7 7 & 7
VL 8 8 8 & 8
CL 9 9 9 & 9
Not Used 10 10 10 & 10
SD 11 11 11 & 11
PL 12 12 12 & 12
Not Used 13 13 13 & 13
Not Used 14 14 14 & 14
Not Used 15 15 15 & 15
STATus:QUEStionable:CONDition? STATus:QUEStionable:EVENt? STATus:QUEStionable:ENABle <NRf>

STATus:QUEStionable:ENABle?
STATus:QUEStionable:NTRansition <NRf>
STATus:QUEStionable:NTRansition?
STATus:QUEStionable:PTRansition <NRf>
STATus:QUEStionable:PTRansition?
Logical OR
To Status Byte Register
Bit Summary Event Bit # Bit Weight

OV (Over-Voltage) 0 1
Over voltage protection has
been tripped
OC (Over-Current) 1 2
Over current protection has
been tripped
POW (AC Power Off) 3 8
AC power switch is off
103
OT (Over Temperature) 4 16
Over temperature protection
has been tripped
VL (Voltage Limit) 8 256
Voltage limit has been reached
CL (Current Limit) 9 512
Current limit has been reached
SD (Shutdown Alarm) 11 2048
PL (Power-Limit) 12 4096
Condition The Questionable Status Condition Register

Register indicates the status of the power supply. If a bit
is set in the Condition register, it indicates that
the event is true. Reading the condition register
does not change the state of the condition
register.
PTR/NTR Filters The PTR/NTR (Positive/Negative transition)

register determines the type of transition
conditions that will set the corresponding bit in
the Event Registers. Use the Positive transition
filter to view events that change from false to
positive, and use the negative transition filter to
view events that change from positive to
negative.
Positive Transition 0→1
Negative Transition 1→0
Event Register The PTR/NTR Register will dictate the type of

transition conditions will set the corresponding
bits in the Event Register. If the Event Register
is read, it will be cleared to 0.
Enable Register The Enable register determines which Events in

the Event Register will be used to set the QUES
bit in the Status Byte Register.
104
REMOTE CONTROL
Operation Status Register Group
Overview The Operation Status Register Group indicates

the operating status of the power supply.
Operation Status Register

CAL 0 0 0 & 0
Not Used 1 1 1 & 1
Not Used 2 2 2 & 2
Not Used 3 3 3 & 3
Not Used 4 4 4 & 4
WTG 5 5 5 & 5
Not Used 6 6 6 & 6
Not Used 7 7 7 & 7
CV 8 8 8 & 8
Not Used 9 9 9 & 9
CC 10 10 10 & 10
OND 11 11 11 & 11
OFD 12 12 12 & 12
Not Used 13 13 13 & 13
PR 14 14 14 & 14
Not Used 15 15 15 & 15
STATus:OPERation:CONDition? STATus:OPERation:EVENt? STATus:OPERation:ENABle <NRf>

STATus:OPERation:ENABle?
STATus:OPERation:NTRansition <NRf>
STATus:OPERation:NTRansition?
STATus:OPERation:PTRansition <NRf>
STATus:OPERation:PTRansition?
Logical OR

CAL (Calibration mode) 0 1
Indicates if the PSW is in
calibration mode.
WTG (Waiting for trigger) 5 32
Indicates if the PSW is waiting
for a trigger.
CV (Constant voltage mode) 8 256
Indicates if the PSW is in CV
mode.
105
CC (Constant current mode) 10 1024

Indicates if the PSW is in CC
mode.
OND (Output ON Delay) 11 2048
Indicates if Output ON delay
time is active
OFD (Output OFF Delay) 12 4096
Indicates if Output OFF delay
time is active
PR (Program Running) 13 8192
Indicates if a Test is running
Condition The Operation Status Condition Register

Register indicates the operating status of the power
supply. If a bit is set in the Condition register,
it indicates that the event is true. Reading the
condition register does not change the state of
the condition register.
PTR/NTR Filters The PTR/NTR (Positive/Negative transition)

register determines the type of transition
conditions that will set the corresponding bit in
the Event Registers. Use the Positive transition
filter to view events that change from false to
positive, and use the negative transition filter
to view events that change from positive to
negative.
Positive Transition 0→1
Negative Transition 1→0
Event Register The PTR/NTR Register will dictate the type of

transition conditions will set the corresponding
bits in the Event Register. If the Event Register
is read, it will be cleared to 0.
106
REMOTE CONTROL
Enable Register The Enable register determines which

registered Events in the Event Register will be
used to set the OPER bit in the Status Byte
Register.
Standard Event Status Register Group
Overview The Standard Event Status Register Group

indicates if any errors have occurred. The bits
of the Event register are set by the error event
queue.

Event Enable
OPC 0 & 0
RQC 1 & 1
QUE 2 & 2
DDE 3 & 3
EXE 4 & 4
CME 5 & 5
URQ 6 & 6
PON 7 & 7
*ESR? *ESE <NRf>

*ESE?
Logical OR

OPC (Operation complete) 0 1
The OCP bit is set when all
selected pending operations are
complete. This bit is set in
response to the *OPC
command.
RQC (Request control) 1 2
QUE (Query Error) 2 4
The Query Error bit is set in
response to an error reading the
Output Queue. This can be
caused by trying to read the
Output Queue when there is no
data present.
107
DDE (Device Dependent Error) 3 8

Device specific error.
EXE (Execution Error) 4 16
The EXE bit indicates an
execution error due to one of the
following: illegal command
parameter, parameter out of
range, invalid parameter, the
command didn’t execute due to
an overriding operation
condition.
CME (Command Error) 5 32
The CME bit is set when a syntax
error has occurred. The CME bit
can also be set when a <GET>
command is received within a
program message.
URQ (User Request) 6 64
PON (Power On) 7 128
Indicates the power is turned on.
Event Register Any bits set in the event register indicate that
an error has occurred. Reading the Event
register will reset the register to 0.
Enable Register The Enable register determines which Events

in the Event Register will be used to set the
ESB bit in the Status Byte Register.
108
REMOTE CONTROL
Status Byte Register & Service Request Enable Register
Overview The Status Byte register consolidates the status

events of all the status registers. The Status
Byte register can be read with the *STB? query
and can be cleared with the *CLS command.
Output
Buffer
:
:
:
Error Que
:
:
:
Service
Status Request
Byte Enable
Register Register
From 0 & 0
Questionable
Status Register 1 & 1
ERR 2 & 2
QUES 3 & 3
From Standard MAV 4 & 4
Event Status ESB 5 & 5
Register MSS 6 6
OPER 7 & 7
*STB? *SRE <NRf>

From Operation
Status Register *SRE?
Logical OR

ERR (Error Event/Queue) 2 4
If data is present in the Error
queue, the ERR bit will be set.
QUES (Questionable Status 3 8
Register)
The summary bit for the
group.
109
MAV (Message Available) This 4 16

is set when there is data in the
Output Queue waiting to be
read.
(ESB) Event Summary Bit. The 5 32
ESB is the summary bit for the
group.
MSS Bit 6 64
The MSS Bit is the summary of
the Status Byte Register and
Service Request register (bits 1-
5, 7). This will be set to 1.
OPER (Operation Status 7 128
Register)
OPER bit is the summary bit for
the Operation Status Register
Group.
Status Byte Any bits set in the Status byte register acts as a
Register summary register for all the three other status
registers and indicates if there is a service
request, an error in the Error Queue or data in
the Output Queue. Reading the Status Byte
register will reset the register to 0.
Service Request The Service Request Enable Register controls

Enable Register which bits in the Status Byte Register are able
to generate service requests.
110
REMOTE CONTROL
Error List
Command Errors
Overview An <error/event number> in the range [ -199 ,

-100 ] indicates that an IEEE 488.2 syntax error
has been detected by the instrument’s parser.
The occurrence of any error in this class shall
cause the command error bit (bit 5) in the event
status register (IEEE 488.2, section 11.5.1) to be
set. One of the following events has occurred:
 An IEEE 488.2 syntax error has been detected
by the parser. That is, a controller-to-device
message was received which is in violation of
the IEEE 488.2 standard. Possible violations
include a data element which violates the
device listening formats or whose type is
unacceptable to the device.
 An unrecognized header was received.
Unrecognized headers include incorrect
device-specific headers and incorrect or
unimplemented IEEE 488.2 common
commands.
Events that generate command errors shall not

generate execution errors, device-specific
errors, or query errors; see the other error
definitions in this chapter.
111
Error Code Description
-100 Command This is the generic syntax error for devices that
Error cannot detect more specific errors. This code
indicates only that a Command Error as
defined in IEEE 488.2,11.5.1.1.4 has occurred.
-102 Syntax error An unrecognized command or data type was

encountered; for example, a string was
received when the device does not accept
strings.
-103 Invalid The parser was expecting a separator and

separator encountered an illegal character; for example,
the semicolon was omitted after a program
message unit,
MEAS:VOLT:DC?:MEASCURR:DC?
-104 Data type The parser recognized a data element different

error than one allowed; for example, numeric or
string data was expected but block data was
encountered.
-108 Parameter More parameters were received than expected

not allowed for the header; for example, the KLOCk
command only accepts one parameter, so
receiving SYSTem:KLOCk 1,0 is not allowed.
-109 Missing Fewer parameters were received than required

parameter for the header; for example, the KLOCk
command requires one parameter, so receiving
KLOCk is not allowed.
-111 Header A character which is not a legal header

separator error separator was encountered while parsing the
header; for example, no white space followed
the header, thus APPL5,1 is an error.
112
REMOTE CONTROL
-112 Program The header contains more that twelve

mnemonic too characters (see IEEE 488.2, 7.6.1.4.1).
long
-113 Undefined The header is syntactically correct, but it is

header undefined for this specific device; for example,
*XYZ is not defined for any device.
-114 Header The value of a numeric suffix attached to a

suffix out of range program mnemonic, see Syntax and Style
section 6.2.5.2, makes the header invalid.
-115 Unexpected The number of parameters received does not

number of correspond to the number of parameters
parameters expected. This is typically due an inconsistency
with the number of instruments in the selected
group.
-120 Numeric This error, as well as errors -121 through -129,

data error are generated when parsing a data element
which appears to be numeric, including the
nondecimal numeric types. This particular
error message should be used if the device
cannot detect a more specific error.
-121 Invalid An invalid character for the data type being

character in parsed was encountered; for example, an alpha
number in a decimal numeric or a “9" in octal data.
-128 Numeric A legal numeric data element was received,

data not allowed but the device does not accept one in this
position for the header.
-131 Invalid suffix The suffix does not follow the syntax described
in IEEE 488.2, 7.7.3.2, or the suffix is
inappropriate for this device.
113
-141 Invalid Either the character data element contains an

character data invalid character or the particular element
received is not valid for the header.
-148 Character A legal character data element was

data not allowed encountered where prohibited by the device.
-151 Invalid string A string data element was expected, but was
data invalid for some reason (see IEEE 488.2,
7.7.5.2); for example, an END message was
received before the terminal quote character.
-158 String data A string data element was encountered but

not allowed was not allowed by the device at this point in
parsing.
-160 Block data This error, as well as errors -161 through -169,
error is generated when parsing a block data
element. This particular error message should
be used if the device cannot detect a more
specific error.
-161 Invalid block A block data element was expected, but was
data invalid for some reason (see IEEE 488.2,
7.7.6.2); for example, an END message was
received before the length was satisfied.
-168 Block data A legal block data element was encountered

not allowed but was not allowed by the device at this point
in parsing.
-178 Expression A legal expression data was encountered but

data not allowed was not allowed by the device at this point in
parsing.
114
REMOTE CONTROL
Execution Errors

-200 ] indicates that an error has been detected
by the instrument’s execution control block.
The occurrence of any error in this class shall
cause the execution error bit (bit 4) in the event
status register (IEEE 488.2, section 11.5.1) to be
set. One of the following events has occurred:
 A <PROGRAM DATA> element following a

header was evaluated by the device as outside
of its legal input range or is otherwise
inconsistent with the device’s capabilities.
 A valid program message could not be

properly executed due to some device
condition.
Execution errors shall be reported by the

device after rounding and expression
evaluation operations have taken place.
Rounding a numeric data element, for
example, shall not be reported as an execution
error. Events that generate execution errors
shall not generate Command Errors, device-
specific errors, or Query Errors; see the other
error definitions in this section.
-200 Execution This is the generic syntax error for devices that
error cannot detect more specific errors. This code
indicates only that an Execution Error as
defined in IEEE 488.2, 11.5.1.1.5 has occurred.
115
-201 Invalid while Indicates that a command is not executable

in local while the device is in local due to a hard local
control (see IEEE 488.2, 5.6.1.5); for example, a
device with a rotary switch receives a message
which would change the switches state, but the
device is in local so the message can’t be
executed.
-203 Command Indicates that a legal password-protected

protected program command or query could not be
executed because the command was disabled.
-211 Trigger Indicates that a GET, *TRG, or triggering signal

ignored was received and recognized by the device but
was ignored because of device timing
considerations; for example, the device was not
ready to respond. Note: a DT0 device always
ignores GET and treats *TRG as a Command
Error.
-213 Init ignored Indicates that a request for a measurement

initiation was ignored as another measurement
was already in progress.
-220 Parameter Indicates that a program data element related

error error occurred. This error message should be
used when the device cannot detect the more
specific errors described for errors -221
through -229.
-221 Settings Indicates that a legal program data element

conflict was parsed but could not be executed due to
the current device state (see IEEE 488.2, 6.4.5.3
and 11.5.1.1.5.).
116
REMOTE CONTROL
-222 Data out of Indicates that a legal program data element

range was parsed but could not be executed because
the interpreted value was outside the legal
range as defined by the device (see IEEE 488.2,
11.5.1.1.5.).
-224 Illegal Used where exact value, from a list of possible,

parameter value was expected.
Device Specific Errors

-300 ] or [ 1 , 32767 ] indicates that the
instrument has detected an error which is not a
command error, a query error, or an execution
error; some device operations did not properly
complete, possibly due to an abnormal
hardware or firmware condition. These codes
are also used for self-test response errors. The
occurrence of any error in this class should
cause the device-specific error bit (bit 3) in the
event status register (IEEE 488.2, section 11.5.1)
to be set. The meaning of positive error codes
is device-dependent and may be enumerated
or bit mapped; the <error message>string for
positive error codes is not defined by SCPI and
available to the device designer.
Note that the string is not optional; if the

designer does not wish to implement a string
for a particular error, the null string should be
sent (for example, 42,""). The occurrence of any
error in this class should cause the device-
specific error bit (bit 3) in the event status
register (IEEE 488.2, section 11.5.1) to be set.
Events that generate device-specific errors
shall not generate command errors, execution
117
errors, or query errors; see the other error

definitions in this section.
-310 System error Indicates that some error, termed “system

error” by the device, has occurred. This code is
device-dependent.
-320 Storage fault Indicates that the firmware detected a fault

when using data storage. This error is not an
indication of physical damage or failure of any
mass storage element.
Query Errors

-400 ] indicates that the output queue control of
the instrument has detected a problem with the
message exchange protocol described in IEEE
488.2, chapter 6. The occurrence of any error in
this class shall cause the query error bit (bit 2)
in the event status register (IEEE 488.2, section
11.5.1) to be set. These errors correspond to
message exchange protocol errors described in
IEEE 488.2, section 6.5. One of the following is
true:
 An attempt is being made to read data from

the output queue when no output is either
present or pending;
 Data in the output queue has been lost.
Events that generate query errors shall not

generate command errors, execution errors, or
device-specific errors; see the other error
definitions in this section.
118
REMOTE CONTROL
-400 Query error This is the generic query error for devices that
cannot detect more specific errors. This code
indicates only that a Query Error as defined in
IEEE 488.2, 11.5.1.1.7 and 6.3 has occurred.
119
APPENDIX
PSW Default Settings
The following default settings are the factory configuration settings
for the power supply (Function settings/Test settings).
Initial Settings Default Setting

Output Off
LOCK 0 (Disabled)
Voltage 0V
Current 0A
OVP Maximum
OCP Maximum
Normal Function
Settings Setting Default Setting
Output ON delay time F-01 0.00s
Output OFF delay time F-02 0.00s
V-I mode slew rate select F-03 0 = CV high speed priority
Rising voltage slew rate F-04 60.00V/s (PSW 30-XX)
80.00V/s (PSW 40-XX)
160.0V/s (PSW 80-XX)
320.0V/s (PSW 160-XX)
500.0V/s (PSW 250-XX)
1600V/s (PSW 800-XX)
Falling voltage slew rate F-05 60.00V/s (PSW 30-XX)
80.00V/s (PSW 40-XX)
160.0V/s (PSW 80-XX)
320.0V/s (PSW 160-XX)
500.0V/s (PSW 250-XX)
1600V/s (PSW 800-XX)
120
APPENDIX
Rising current slew rate F-06 72.00A/s (PSW 30-36)

144.0A/s (PSW 30-72)
216.0A/s (PSW 30-108)
54.00A/s (PSW 40-27)
108.0A/s (PSW 40-54)
162.0A/s (PSW 40-81)
27.00A/s (PSW 80-13.5)
54.00A/s (PSW 80-27)
81.00A/s (PSW 80-40.5)
14.40A/s (PSW 160-7.2)
28.80A/s (PSW 160-14.4)
43.20A/s (PSW 160-21.6)
9.000A/s (PSW 250-4.5)
18.00A/s (PSW 250-9)
27.00A/s (PSW 250-13.5)
2.880A/s (PSW 800-1.44)
5.760A/s (PSW 800-2.88)
8.640A/s (PSW 800-4.32)
Falling current slew rate F-07 72.00A/s (PSW 30-36)
144.0A/s (PSW 30-72)
216.0A/s (PSW 30-108)
54.00A/s (PSW 40-27)
108.0A/s (PSW 40-54)
162.0A/s (PSW 40-81)
27.00A/s (PSW 80-13.5)
54.00A/s (PSW 80-27)
81.00A/s (PSW 80-40.5)
14.40A/s (PSW 160-7.2)
28.80A/s (PSW 160-14.4)
43.20A/s (PSW 160-21.6)
9.000A/s (PSW 250-4.5)
18.00A/s (PSW 250-9)
27.00A/s (PSW 250-13.5)
2.880A/s (PSW 800-1.44)
5.760A/s (PSW 800-2.88)
8.640A/s (PSW 800-4.32)
Internal resistance F-08
0.000Ω
setting
Bleeder circuit control F-09 1 = ON
Buzzer ON/OFF control F-10 1 = ON
121
Measurement Average F-17

0 = Low
Setting
Lock Mode F-19 0 = Panel lock: allow output off
USB/GPIB setting
Rear Panel USB Mode F-22 2 = USB CDC
GPIB address F-23 8
LAN setting
LAN F-36 1 = Enable
DHCP F-37 1 = Enable
Sockets active F-57 1 = Enable
Web Server active F-59 1 = Enable
Web password active F-60 1 = Enable
Web setting password F-61 0000
Power On Configuration
CV Control F-90 0= Panel control (local)
CC Control F-91 0= Panel control (local)
Power-ON Output F-92 0 = OFF at startup
Master/Slave F-93 0 = Master/Local
External Out Logic F-94 0= High ON
Power Switch trip F-95 0 = Enable
122
APPENDIX
Error Messages & Messages

The following error messages or messages may appear on the PSW
screen during operation.
Error Messages Description

Err 001 USB Mass Storage is not present
Err 002 No (such)file in USB mass storage
Err 003 Empty memory location
Err 004 File access error
Err 901 Keyboard CPLD error
Err 902 Analog CPLD error
Err 920 The ADC is over range for calibration
Err 921 The DAC is over range for calibration
Err 922 Point invalid for calibration
Messages Description
MSG 001 External control of output. Output off (F-94=0,
High=on)
MSG 002 External control of output. Output off (F-94=1,
Low=on)
MSG 003 F-93 is not zero. Unable to calibrate.
LOCK F-19 F-19 is not zero. Unable to turn the output on.
LED Display Format

Use the following table to read the LED display messages.
0 1 2 3 4 5 6 7 8 9 A B C D
E F G H I J K L M N O P Q R
S T U V W X Y Z ( ) + - ,
123
INDEX symbol ............................................. 4

Accessories ................................. 10
Caution symbol ........................... 4 LED conversion ........................ 123
Cleaning the instrument ............. 5 List of features .............................. 9
Configuration Messages ................................... 123
normal function settings Model differences ........................ 8
operation .................................. 21 Rear panel diagram ................... 17
overview ........................................ 21 Remote control ........................... 29
power on configuration operation22 Command list ............................... 52
table................................................ 24 Command syntax......................... 48
Connector plug manufacturer . 19 Error list ...................................... 111
DECA SwitchLab....................... 19 GPIB configuration ...................... 30
Display format ......................... 123 Status registers ........................... 101
Disposal instructions................... 6 USB configuration........................ 30
EN61010 Remote control function check 34
pollution degree ............................. 6 Realterm ........................................ 35
Environment Service operation
safety instruction ............................ 5 about disassembly ......................... 5
Error messages ......................... 123 Socket server examples
Ethernet C++ ................................................ 45
interface ......................................... 32 LabVIEW....................................... 47
sockets ........................................... 33 Visual basic ................................... 44
web server ..................................... 32 Socket server function check .... 38
Front panel diagram ................. 14 Warning symbol .......................... 4
Ground Web server function check ....... 38
124

Multi-Range DC Power Supply: PSW Series

Uploaded by

Copyright:

Available Formats

Multi-Range DC Power Supply: PSW Series

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Multi-Range DC Power Supply: PSW Series

Uploaded by

Copyright:

Available Formats

Multi-Range DC Power Supply

ISO-9001 CERTIFIED MANUFACTURER

The information in this manual was correct at the time of printing.

Good Will Instrument Co., Ltd.

GETTING STARTED .......................................................... 7

REMOTE CONTROL ....................................................... 29

APPENDIX .................................................................... 120

INDEX .......................................................................... 124

Warning: Identifies conditions or practices that

Caution: Identifies conditions or practices that

DANGER High Voltage

Attention Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

Do not dispose electronic equipment as unsorted

General  Do not place any heavy object on the PSW.

Cleaning the PSW  Disconnect the power cord before cleaning.

Operation  Location: Indoor, no direct sunlight, dust free,

 Mains supply voltage fluctuations: +/-10 %

Storage  Location: Indoor

PSW Series Overview ................................................... 8

PSW Series Overview

Throughout the user manual, PSW 30, PSW 40,

Model name Type Voltage Rating Current Rating Power

PSW 250-13.5 Type III 0~250V 0~13.5A 1080W

360 Watt models 720 Watt models 1080 Watt models

VSR VSR VSR

Function OVP/OCP Set Function OVP/OCP Set Function OVP/OCP Set

Performance  High performance/power

Features  OVP, OCP and OHP (OTP) protection

 Power on configuration settings.

Interface  Ethernet port

PSW 30/40/80/160 Accessories

Standard Part number Description

Optional Part number Description

PSW-003 Contact Removal

PSW-005 Series operation cable for 2 units.

PSW 250/800 Accessories

Standard Part number Description

PSW-003 Contact Removal

PSW-006 Parallel operation cable for 2 units.

GUG-001 GPIB to USB adapter

PSW Front Panel

1080W: PSW 30-108, 40-81, 80-40.5, 160-21.6, 360W: PSW 30-36,

Multi-Range DC Power Supply Voltage Multi-Range DC Power Supply Voltage

Function OVP/OCP Set Function OVP/OCP Set

Test Lock/Local PWR DSPL Test Lock/Local PWR DSPL

Function The Function key is used to

OVP/OCP Set the over current or over

Set Sets the current and voltage limits.

Test Used to run customized scripts for

Lock/Local Locks or unlocks the panel keys to

PWR DSPL Toggles the display from viewing

Display VSR Voltage Slew Rate

Voltage Knob Voltage

Current Knob Current

Output Output Press to turn on the output. The

USB USB A port for data transfer,

Power Switch Used to turn the power on/off.