DIN 433 Spec
DIN 433 Spec
Nominal D1 D2 H H weight
For Thread
size min. max. max. min. Nominal size max. min. kg/1000pcs
M1 1.1 1.1 1.24 2.5 2.25 0.3 0.35 0.25 0.01
M1.2 1.3 1.3 1.44 3 2.75 0.3 0.35 0.25 0.012
M1.4 1.5 1.5 1.64 3 2.75 0.3 0.35 0.25 0.013
M1.6 1.7 1.7 1.84 3.5 3.2 0.3 0.35 0.25 0.017
M1.8 2 2 2.14 4 3.7 0.3 0.35 0.25 0.022
M2 2.2 2.2 2.34 4.5 4.2 0.3 0.35 0.25 0.029
M2.5 2.7 2.7 2.64 5 4.7 0.5 0.55 0.45 0.065
M3 3.2 3.2 3.38 6 5.7 0.5 0.55 0.45 0.079
M3.5 3.7 3.7 3.88 7 6.64 0.5 0.55 0.45 0.109
M4 4.3 4.3 4.48 8 7.64 0.5 0.55 0.45 0.14
M5 5.3 5.3 5.48 9 8.64 1 1.1 0.9 0.32
M6 6.4 6.4 6.62 11 10.57 1.6 1.8 1.4 0.79
M8 8.4 8.4 8.62 15 14.57 1.6 1.8 1.4 1.52
M10 10.5 10.5 10.77 18 17.57 1.6 1.8 1.4 2.11
M12 13 13 13.27 20 19.48 2 2.2 1.8 2.65
M14 15 15 15.27 24 23.48 2.5 2.7 2.3 5.41
M16 17 17 17.27 28 27.48 2.5 2.7 2.3 7.63
M18 19 19 19.33 30 29.48 2.5 2.7 2.3 8.31
M20 21 21 21.33 34 33.38 3 3.3 2.7 13.2
M24 25 25 25.33 39 39.38 4 4.3 3.7 22.1
M30 31 31 31.39 50 49.38 4 4.3 3.7 38
M36 37 37 37.62 58 56.8 5 5.6 4.4 61.5
Aspen Fasteners 4807 Rockside Road, Suite 400, Independence, OH 44131 USA
www.aspenfasteners.com | aspensales@aspenfasteners.com | 1-800-479-0056
DIN (Deutsches Institut für Normung - German Institute for Standardization) standards are issued for a variety of components
including industrial fasteners as Metric DIN 433 Flat Washers. The DIN standards remain common in Germany, Europe and
globally even though the transition to ISO standards is taking place. DIN standards continue to be used for parts which do not
have ISO equivalents or for which there is no need for standardization. In this case the ISO equivalent is ISO 7092.
1) Mechanical properties of stainless steel for metric DIN 433 Flat Washers
Stainless steels can be divided into three groups of steel - austenitic, ferritic and martensitic. Austenitic steel is by
far the most common type (>90% of commercial fasteners). The steel groups and strength classes are designated by a four-digit
sequence of letters and numbers (eg A2-70) as shown in the following table. DIN EN ISO 3506 governs screws and nuts made
from stainless steel.
Tensile Tensile
Strength strength strength Dia range Nut Load
Steel group Steel grade N/mm2 PSI
class N/mm2
Aspen Fasteners 4807 Rockside Road, Suite 400, Independence, OH 44131 USA
www.aspenfasteners.com | aspensales@aspenfasteners.com | 1-800-479-0056
17.5 8.0
≤
X 5Cr Ni 1810 1.4301 1.0 2.0 to - to
0.07
19.5 10.5
18.0 10
≤
A2 304 X 2 Cr Ni 1811 1.4306 1.0 2.0 to - to
0.03
20.0 12.0
17.0 11.0
≤
X 8 Cr Ni 19/10 1.4303 1.0 2.0 to - to
0.07
19.0 13.0
16.5 2.0 10.0
≤
X 5 Cr Ni Mo 1712 1.4401 1.0 2.0 to to to
0.07
18.5 2.5 13.0
A4 316
16.5 2.0 10
≤
X 2 Cr Ni Mo 1712 1.4404 1.0 2.0 to to to
0.03
18.5 2.5 13
Aspen Fasteners 4807 Rockside Road, Suite 400, Independence, OH 44131 USA
www.aspenfasteners.com | aspensales@aspenfasteners.com | 1-800-479-0056
PROPERTY CLASS
8.8
MECHANICAL PROPERTY
4.8 5.6 5.8 6.8 Up to M Over M 9.8 10.9 12.9
16 16
Tensile Strength nom. 400 500 600 800 900 1000 1200
(Rm, N/mm²) min. 420 500 520 600 800 830 900 1040 1220
min. 130 155 160 190 250 255 290 320 385
Vickers Hardness
max 250 320 336 360 380 435
min. 124 147 152 181 319 242 266 295 353
Brinell Hardness
max. 238 385 319 342 363 412
min. HR 71 79 82 89 -
HRC - - - - 20 23 28 32 39
Rockwell Hardness
HR 95 99 -
max. HRC - - - - 32 34 37 39 44
Yield Stress ReL. nom. 320 300 400 480 -
N/mm² min. 340 300 420 480 -
Stress at permanent nom. - 640 720 900 1080
set limit N/mm² min. - 640 660 720 940 1100
Disclaimer
Dimensional data and technical information for Metric DIN 433 Flat Washers was obtained from publicly available sources and
not acquired through standards agencies. It has been completed and compiled for reference purposes only; where
discrepancies are found they are subject to change without notice. Aspen Fasteners makes no warranties or representations
regarding the accuracy and validity of the compiled information and data. Contact the relevant standards authorities for accurate
and detailed information.
Aspen Fasteners 4807 Rockside Road, Suite 400, Independence, OH 44131 USA
www.aspenfasteners.com | aspensales@aspenfasteners.com | 1-800-479-0056