Datasheet

400KHz 60V 2A Switching Current Boost LED Constant Current Driver XL6003

Features General Description

 Wide 3.6V to 24V Input Voltage Range The XL6003 regulator is fixed frequency
 0.22V FB adjustable LED drive current PWM Boost (step-up) LED constant current
 Directly drive 6 Series 1W LED at driver, capable of driving Series 1W LED
VIN>=12V units with excellent line and load regulation.
 Fixed 400KHz Switching Frequency The regulator is simple to use because it
 Max. 2A Switching Current Capability includes internal frequency compensation
 Up to 92% efficiency and a fixed-frequency oscillator so that it
 Excellent line and load regulation requires a minimum number of external
 EN PIN TTL shutdown capability components to work.
 Internal Optimize Power MOSFET The XL6003 could directly drive 6 Series 1W
 Built in Soft-Start Function LED units at VIN>=12V .
 Built in Frequency Compensation
 Built in Thermal Shutdown Function The PWM control circuit is able to adjust the
 Built in Current Limit Function duty ratio linearly from 0 to 90%. An enable
 Available in SOP8 package function, an over current protection function
is built inside. An internal compensation
block is built in to minimize external
Applications component count.
 LED Lighting
 Boost constant current driver
 Monitor LED Backlighting
 7’to 15’LCD Panels

Figure1. Package Type of XL6003

Rev 2.0 www.xlsemi.com

1
 Datasheet

400KHz 60V 2A Switching Current Boost LED Constant Current Driver XL6003

Pin Configurations

EN 1 8 GND

VIN 2 7 GND
XL6003
FB 3 6 SW

NC 4 5 SW

Figure2. Pin Configuration of XL6003 (Top View)

Table 1 Pin Description

Pin Number Pin Name Description

Enable Pin. Drive EN pin low to turn off the device, drive it high
1 EN
to turn it on. Floating is default high.
Supply Voltage Input Pin. XL6003 operates from a 3.6V to 24V
2 VIN DC voltage. Bypass Vin to GND with a suitably large capacitor
to eliminate noise on the input.
3 FB Feedback Pin (FB). The feedback threshold voltage is 0.22V.
4 NC No Connected.
Power Switch Output Pin (SW). Output is the switch node that
5,6 SW
supplies power to the output.
7,8 GND Ground Pin.

Rev 2.0 www.xlsemi.com

2
 Datasheet

400KHz 60V 2A Switching Current Boost LED Constant Current Driver XL6003

Function Block

VIN EN
SW
2.5V OVP
UVLO
2.5V Regulator
0.22V 0.22V Reference

Thermal
Soft Start Shutdown

EA
FB Driver
COMP RS Latch NDMOS

Slop Compensation
OCP

Phase Compensation

Oscillator GND
400KHz

Figure3. Function Block Diagram of XL6003

Typical Application Circuit

L1 22uh/2A D1 SS34

C2
COUT
105
47uF
35V

SW Series 6 1W LED
5,6
VIN FB
2 XL6003 3
7,8 1
GND EN
C1
+12V CIN 105 ON
47uF OFF RS
25V 350mA

ILED=0.22/RS

Figure4. XL6003 Typical Application Circuit

Rev 2.0 www.xlsemi.com

3
 Datasheet

400KHz 60V 2A Switching Current Boost LED Constant Current Driver XL6003

Ordering Information

Order Information Marking ID Package Type Packing Type Supplied As

XL6003E1 XL6003E1 SOP8 2500/4000 Units on Tape & Reel

XLSEMI Pb-free products, as designated with “E1” suffix in the par number, are RoHS compliant.

Absolute Maximum Ratings（Note1）

Parameter Symbol Value Unit
Input Voltage Vin -0.3 to 26 V
Feedback Pin Voltage VFB -0.3 to Vin V
EN Pin Voltage VEN -0.3 to Vin V
Output Switch Pin Voltage VSW -0.3 to 60 V
Power Dissipation PD Internally limited mW
Thermal Resistance (SOP8) o
RJA 100 C/W
(Junction to Ambient, No Heatsink, Free Air)
o
Operating Junction Temperature TJ -40 to 125 C
o
Storage Temperature TSTG -65 to 150 C
o
Lead Temperature (Soldering, 10 sec) TLEAD 260 C
ESD (HBM) >2000 V

Note1: Stresses greater than those listed under Maximum Ratings may cause permanent
damage to the device. This is a stress rating only and functional operation of the device at
these or any other conditions above those indicated in the operation is not implied. Exposure
to absolute maximum rating conditions for extended periods may affect reliability.

Rev 2.0 www.xlsemi.com

4
 Datasheet

400KHz 60V 2A Switching Current Boost LED Constant Current Driver XL6003

XL6003 Electrical Characteristics

o
Ta = 25 C;unless otherwise specified.

Symbol Parameter Test Condition Min. Typ. Max. Unit

System parameters test circuit figure4

Feedback Vin = 5V to 12V, Vout=24V

VFB 209 220 231 mV
Voltage Iload=100mA
Vin=12V ,Vout=24V
η Efficiency - 92 - %
Iout=0.3A

Electrical Characteristics (DC Parameters)

Vin = 12V, GND=0V, Vin & GND parallel connect a 100uf/50V capacitor; Iout=100mA, Ta = 25℃;
the others floating unless otherwise specified.

Parameters Symbol Test Condition Min. Typ. Max. Unit

Input operation voltage Vin 3.6 24 V

Shutdown Supply Current IS VEN=0V 70 100 uA

VEN =2V,
Quiescent Supply Current Iq 2.5 5 mA
VFB =Vin

Oscillator Frequency Fosc 320 400 480 Khz

Switch Current Limit IL VFB =0V 2 A

Vin=12V,
Output Power NMOS Rdson 110 120 mohm
ISW=2A

High (Regulator ON) 1.4

EN Pin Threshold VEN V
Low (Regulator OFF) 0.8

EN Pin Input Leakage IH VEN =2V (ON) 3 10 uA

Current IL VEN =0V (OFF) 3 10 uA

Max. Duty Cycle DMAX VFB=0V 90 %

Rev 2.0 www.xlsemi.com

5
 Datasheet

400KHz 60V 2A Switching Current Boost LED Constant Current Driver XL6003

Typical System Application for VIN=5V to driver 3 x 1W series LED units

L1 22uh/2A D1 SS34

C2
COUT
105
47uF
35V

SW Series 3 1W LED
5,6
VIN FB
2 XL6003 3
7,8 1
GND EN
C1
+5V CIN 105 ON
47uF OFF RS
16V 350mA

ILED=0.22/RS

Figure5. XL6003 System Parameters Test Circuit (5V ~ 3 x 1W LED)

Typical System Application for VIN>=12V to driver 6 x 1W series LED units

L1 22uh/2A D1 SS34

C2
COUT
105
47uF
35V

SW Series 6 1W LED
5,6
VIN FB
2 XL6003 3
7,8 1
GND EN
C1
+12V CIN ON
105
47uF OFF RS
25V 350mA

ILED=0.22/RS

Figure6. XL6003 System Parameters Test Circuit (12V ~ 6 x 1W LED)

Rev 2.0 www.xlsemi.com

6
 Datasheet

400KHz 60V 2A Switching Current Boost LED Constant Current Driver XL6003

Typical System Application for VIN>=12V to driver 6 series x 28 parallel White LED Array

L1 22uh/2A D1 SS34

C2
COUT
105
47uF
50V
Series 6 Series 6 Series 6
SW 20ma White LED 20ma White LED 20ma White LED
5,6
VIN FB
2 XL6003 3 N= 1~28 Units Parallel
7,8 1
GND EN
C1
+12V CIN 105 ON RS
47uF
25V OFF
N * 20mA

ILED=0.22/RS

Figure7. XL6003 System Parameters Test Circuit (12V ~ 6 x 28 White LED)

Typical System Application for SEPIC Buck-Boost LED Driver

L1A 33uh/2A L1B 33uh/2A

D1 SS36

C2
COUT
105
47uF
35V
CDC 22uF/50V Series 4 1W LED
SW
5,6
VIN FB
2 XL6003 3

7,8 1
GND EN
C1
VIN CIN 105 ON
47uF RS
OFF 350mA
35V

ILED=0.22/RS
Buck-Boost LED Driver
Input 8V ~ 16V
Output Drive series 4 1W LED

Figure8. XL6003 System Parameters Test Circuit (Buck-Boost LED Driver)

Rev 2.0 www.xlsemi.com

7
 Datasheet

400KHz 60V 2A Switching Current Boost LED Constant Current Driver XL6003

Typical System Application for VIN>=12V to driver 6 x 1W series LED units With Dimming
Function

L1 22uh/2A D1 SS34

C2
COUT
105
47uF
35V

SW Series 6 1W LED
5,6
VIN FB R1
2 XL6003 3
7,8 1
R2
GND EN
+12V C1
CIN
105
47uF RS
R3 C3
25V 350mA
105

PWM Dimming

Figure9. XL6003 System Parameters Test Circuit (12V ~ 6 x 1W LED with Dimming Function)
Typical System Application (LED Open Protection)
LED Open Protection function can be used in typical system application with external
components. The output voltage can be limited in a suitable value by choosing different zener
diode when the output LED open. the zener diode voltage choosed by output led voltage's 1.3
times.

L1 22uH/2A D1 SS36

DZ LED
ZENER
SW
5,6
VIN FB R1 2K C2 COUT
2 XL6003 3
105 100uF
7,8 1 63V
GND EN
CIN C1
VIN
47uF 105 RCS
35V

ILED=0.22/RCS
VDZ=1.3*VOUT<60V

Figure10. XL6003 System Parameters Test Circuit (LED Open Protection)

Rev 2.0 www.xlsemi.com

8
 Datasheet

400KHz 60V 2A Switching Current Boost LED Constant Current Driver XL6003

Package Information

SOP8

Dimensions In Millimeters Dimensions In Millimeters

Symbol
Min. Nom. Max. Min. Nom. Max.
A 1.35 1.55 1.75 0.053 0.061 0.069
A1 0.05 - 0.25 0.002 - 0.010
A2 1.25 1.40 1.65 0.049 0.055 0.065
A3 0.50 0.60 0.70 0.019 0.024 0.028
b 0.30 - 0.51 0.012 - 0.020
b1 0.29 0.41 0.48 0.011 0.016 0.018
c 0.17 - 0.25 0.007 - 0.010
c1 0.17 0.20 0.23 0.007 0.008 0.009
D 4.70 4.90 5.10 0.185 0.193 0.200
E 5.80 6.00 6.20 0.228 0.236 0.244
E1 3.80 3.90 4.00 0.150 0.154 0.157
e 1.14 1.27 1.40 0.045 0.050 0.055
h 0.25 - 0.50 0.010 - 0.020
L 0.45 - 0.80 0.017 - 0.031
L1 0.82 1.03 1.23 0.032 0.040 0.048
θ 0 - 8° 0 - 8°

Rev 2.0 www.xlsemi.com

9
 Datasheet

400KHz 60V 2A Switching Current Boost LED Constant Current Driver XL6003

Important Notice
XLSEMI reserve the right to make modifications, enhancements, improvements, corrections
or other changes without notice at any time. XLSEMI does not assume any liability arising out
of the application or use of any product described herein; neither does it convey any license
under its patent rights, nor the rights of others. XLSEMI assumes no liability for applications
assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using XLSEMI components. To minimize the risks associated with Buyers’
products and applications, Buyers should provide adequate design and operating safeguards.
XLSEMI warrants performance of its products to the specifications applicable at the time of
sale, in accordance with the warranty in XLSEMI’s terms and conditions of sale of
semiconductor products. Testing and other quality control techniques are used to the extent
XLSEMI deems necessary to support this warranty. Except where mandated by applicable
law, testing of all parameters of each component is not necessarily performed.
For the latest product information, go to www.xlsemi.com.

Rev 2.0 www.xlsemi.com

10