Fj44 Service Bulletin: 1. Planning Information

FJ44 SERVICE BULLETIN
Engine – Rear Mount Sleeve – Install
1. Planning Information
A. Effectivity:
This service bulletin applies to the following Williams International turbofan

engines:
ENGINE ENGINE
MODEL PART
NUMBER NUMBER ENGINE SERIAL NUMBERS
FJ44-1A 45700-104 1987
FJ44-2A 56000 301 – 306, 1001 – 1015, 1017 – 1056, 1058 -
1072
FJ44-2A 56000-104 601 – 602, 6001 – 6002, 116015, 116074 –
116075, 1016, 1057
FJ44-2A 56000-106 102
FJ44-2A 56000-107 312
FJ44-2C 60500 501, 1001 – 1072
FJ44-2C 60500-103 3001 – 3002
B. Reason:
The Rear Mount Sleeve (P/N 66750) provides additional fire protection for the
rear mount to comply with EASA requirements.
Revision 6 updated the engine effectivity. This revision has no affect on engines
previously in compliance with this service bulletin.
C. Compliance:
This Service Bulletin is OPTIONAL and should be accomplished prior to the

delivery of an aircraft registered to an EASA nation.
D. Description:
This Service Bulletin gives instructions to:
(1) Disconnect the rear mount from the airframe, if installed.
(2) Remove the rear mount ring.
(3) Install the rear mount sleeve.
(4) Re-install the rear mount ring, bypass duct and connect to the airframe.
March 20/2001 FJ44-72-042

Revision 6, Jan. 18/2010 Page 1 of 5
E. Approval:
This Service Bulletin has been reviewed by the appropriate governmental

authority and the technical content herein complies with applicable Aviation
Regulations and are APPROVED.
F. Manpower:
5.0 hours Installed engines

0.5 hours Uninstalled engines
G. Material:
PART NUMBER NOMENCLATURE QUANTITY NOTE

65172 Rear Mount Sleeve 1 FJ44-2A Only
66750 Rear Mount Sleeve 1 All FJ44-2
66750RWK66787 Rear Mount Sleeve 1 Only if reworking
65172 for 2C
Refer to Illustrated Parts Catalog for current part prices
H. Tooling Required:
Refer to the referenced procedures in the FJ44-2A and FJ44-2C Maintenance

Manuals or the applicable Repair Station rework instructions.
I. Weight and Balance:
0.26 lbs. weight increase
J. Electrical Load Data:
Not applicable
K. Software Accomplishment Summary:
Not applicable
L. References:
Aircraft Maintenance Manual

FJ44-1A Maintenance Manual
FJ44-2A Maintenance Manual
FJ44-2C Maintenance Manual
M. Other Publications Affected:
Not applicable
March 20/2001 FJ44-72-042

N. Family Tree Charts of Modification Relationships:
Not applicable
March 20/2001 FJ44-72-042

2. Accomplishment Instructions
A. If engine is installed on aircraft, proceed to step B. If engine is not installed on
aircraft, proceed to step D.
B. Disconnect the rear engine mount from the airframe in accordance with the Aircraft
Maintenance Manual.
C. Remove the rear bypass duct and mount ring per 72-00-70, P.B. 401 in the
appropriate FJ44 Maintenance Manual as applicable.
NOTE: It is acceptable to apply 3 or 4 drops of engine oil to aid in installation.
D. Install rear mount sleeve over rear mount ball socket (swivel) engaging the flanges
of the sleeve with the flange on the rear mount ring.
E. Center the sleeve hole to the swivel and adjust mounting bolt slots so bolts are
within slotted area of sleeve. Wipe off any residual oil.
F. Reinstall rear mount and rear bypass duct per 72-00-70, P.B. 401 in the appropriate
FJ44 Maintenance Manual as applicable.
G. Verify the sleeve is not pinched between the front and rear duct flanges and that it is
resting on the outside of the front and rear duct flange.
H. Reinstall rear mount to airframe in accordance with the Aircraft Maintenance

Manual.
I. Record the accomplishment of this Service Bulletin in the engine logbook.
J. Register your compliance with this Service Bulletin by filling out the Certificate of
Compliance and returning it to the address shown.
March 20/2001 FJ44-72-042

CERTIFICATE OF COMPLIANCE
TO: Operator, Service Center, or Repair Center Performing Service Bulletin
Upon completion of this service bulletin, please fill in the information requested below. You may
return this information to Williams International by scanning and emailing to
WIProductSupport@williams-int.com or faxing it to (1-248-669-9515) or by regular mail.
Williams International
2280 E. West Maple Road
P.O. Box 200
Walled Lake, MI 48390-0200
USA
Attention: Product Support
Owner/Operator
City/State/Zip
A/C Registration No. Engine

Part No. Model No.
Eng. Serial No.

No. 1 No. 2
Component
Part No.
No. 1 No. 2
Component
Serial No.
No. 1 No. 2
TSN
No. 1 No. 2
TSO
No. 1 No. 2
Cycles
No. 1 No. 2
Date of Final __________________ __________________________

Operational Check
I certify the following service bulletin has been accomplished:
Service Bulletin Title: Engine – Rear Mount Sleeve – Install
Signature: _____________________________ Date: _______________
Title Representing
March 20/2001 FJ44-72-042


Fj44 Service Bulletin: 1. Planning Information

Uploaded by

Copyright:

Available Formats

Fj44 Service Bulletin: 1. Planning Information

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Fj44 Service Bulletin: 1. Planning Information

Uploaded by

Copyright:

Available Formats

FJ44 SERVICE BULLETIN

Engine – Rear Mount Sleeve – Install

This service bulletin applies to the following Williams International turbofan

This Service Bulletin is OPTIONAL and should be accomplished prior to the

This Service Bulletin gives instructions to:

(1) Disconnect the rear mount from the airframe, if installed.

(2) Remove the rear mount ring.

(3) Install the rear mount sleeve.

March 20/2001 FJ44-72-042

This Service Bulletin has been reviewed by the appropriate governmental

5.0 hours Installed engines

PART NUMBER NOMENCLATURE QUANTITY NOTE

Refer to the referenced procedures in the FJ44-2A and FJ44-2C Maintenance

I. Weight and Balance:

0.26 lbs. weight increase

J. Electrical Load Data:

K. Software Accomplishment Summary:

Aircraft Maintenance Manual

M. Other Publications Affected:

March 20/2001 FJ44-72-042

March 20/2001 FJ44-72-042

NOTE: It is acceptable to apply 3 or 4 drops of engine oil to aid in installation.

H. Reinstall rear mount to airframe in accordance with the Aircraft Maintenance

I. Record the accomplishment of this Service Bulletin in the engine logbook.

March 20/2001 FJ44-72-042

TO: Operator, Service Center, or Repair Center Performing Service Bulletin

A/C Registration No. Engine

Eng. Serial No.

Date of Final __________________ __________________________

I certify the following service bulletin has been accomplished:

Service Bulletin Title: Engine – Rear Mount Sleeve – Install

Signature: _____________________________ Date: _______________

March 20/2001 FJ44-72-042

You might also like

Date of Final ________

Signature: _______________ Date: _