Screenshot 2023-04-20 at 1.43.28 PM

TI01000F/00/EN/23.
20 Products Solutions Services

71488020
2020-07-31
Technical Information
Levelflex FMP50
Guided wave radar
Level measurement in liquids
Application
• Rod or rope probe
• Process connection: 3/4" thread or adapter flange
• Process temperature: –20 to +80 °C (–4 to +176 °F)
• Process pressure: –1 to +6 bar (–14.5 to +87 psi)
• Maximum measuring range: Rod 4 m (13 ft); rope 12 m (39 ft)
• Accuracy: ±2 mm (±0.08 in)
• International explosion protection certificates; WHG; EN10204-3.1
• Linearity protocol (3-point, 5-point)
Your benefits
• Reliable measurement even for changing product and process conditions
• HistoROM data management for easy commissioning, maintenance and
diagnostics
• Highest reliability due to Multi-Echo Tracking
• Hardware and software developed according to IEC 61508 (up to SIL3)
• Seamless integration into control or asset management systems
• Intuitive user interface in national languages
• Bluetooth® wireless technology for commissioning, operation and maintenance via
free iOS / Android app SmartBlue
• Easy proof test for SIL and WHG
• Heartbeat Technology™
Levelflex FMP50
Table of contents
Important document information . . . . . . . . . . . . . . . 4 Process pressure range . . . . . . . . . . . . . . . . . . . . . . . . . 53

Symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Dielectric constant (DC) . . . . . . . . . . . . . . . . . . . . . . . . 53
Extension of the rope probes due to temperature . . . . . . . . 53
Function and system design . . . . . . . . . . . . . . . . . . . 5
Measuring principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Mechanical construction . . . . . . . . . . . . . . . . . . . . 54
Measuring system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Probe length tolerances . . . . . . . . . . . . . . . . . . . . . . . . 57
Shortening probes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Measured variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Materials: GT19 housing (plastic) . . . . . . . . . . . . . . . . . . 59
Measuring range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Materials: GT20 housing (die-cast aluminum, powder-
Blocking distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
coated) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Measuring frequency spectrum . . . . . . . . . . . . . . . . . . . 10
Materials: Process connection . . . . . . . . . . . . . . . . . . . . 62
Materials: Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Materials: Mounting bracket . . . . . . . . . . . . . . . . . . . . . 64
Output signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Materials: Adapter and cable for remote sensor . . . . . . . . 65
Signal on alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Materials: Weather protection cover . . . . . . . . . . . . . . . . 66
Linearization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Galvanic isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Protocol-specific data . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Operating concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Local operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Operation with remote display and operating module
Terminal assignment . . . . . . . . . . . . . . . . . . . . . . . . . . 18 FHX50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Device plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Operation via Bluetooth® wireless technology . . . . . . . . . . 69
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Integration in tank gauging system . . . . . . . . . . . . . . . . . 73
Current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . 30 SupplyCare inventory management software . . . . . . . . . . 74
Power supply failure . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Potential equalization . . . . . . . . . . . . . . . . . . . . . . . . . 31
Certificates and approvals . . . . . . . . . . . . . . . . . . . 77
Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
CE mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Cable entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Cable specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
RCM-Tick marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Overvoltage protection . . . . . . . . . . . . . . . . . . . . . . . . . 32
Ex approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Dual seal according to ANSI/ISA 12.27.01 . . . . . . . . . . . . 77
Performance characteristics . . . . . . . . . . . . . . . . . . 33 Functional safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Reference operating conditions . . . . . . . . . . . . . . . . . . . 33 Overfill prevention . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Reference accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Pressure equipment with allowable pressure
Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 ≤ 200 bar (2 900 psi) . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Response time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Radio approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Influence of ambient temperature . . . . . . . . . . . . . . . . . 35 Test, certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Hard-copy product documentation . . . . . . . . . . . . . . . . . 78
Other standards and guidelines . . . . . . . . . . . . . . . . . . . 79
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Installation conditions . . . . . . . . . . . . . . . . . . . . . . . . . 36
Ordering information . . . . . . . . . . . . . . . . . . . . . . . 80
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Operating conditions: Environment . . . . . . . . . . . . 50
3-point linearity protocol . . . . . . . . . . . . . . . . . . . . . . . 81
Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5-point linearity protocol . . . . . . . . . . . . . . . . . . . . . . . 82
Ambient temperature limits . . . . . . . . . . . . . . . . . . . . . 50
Customer-specific configuration . . . . . . . . . . . . . . . . . . . 83
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Tagging (TAG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Climate class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Altitude according to IEC61010-1 Ed.3 . . . . . . . . . . . . . . 52
Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Application packages . . . . . . . . . . . . . . . . . . . . . . . 84
Vibration resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Heartbeat Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . 84
Cleaning the probe . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Heartbeat Verification . . . . . . . . . . . . . . . . . . . . . . . . . 85
Electromagnetic compatibility (EMC) . . . . . . . . . . . . . . . 52 Heartbeat Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . 86
Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Process temperature range . . . . . . . . . . . . . . . . . . . . . . 53 Device-specific accessories . . . . . . . . . . . . . . . . . . . . . . 87
2 Endress+Hauser
Levelflex FMP50
Communication-specific accessories . . . . . . . . . . . . . . . . 94
Service-specific accessories . . . . . . . . . . . . . . . . . . . . . . 95
System components . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Supplementary documentation . . . . . . . . . . . . . . . 95
Brief Operating Instructions (KA) . . . . . . . . . . . . . . . . . . 95
Operating Instructions (BA) . . . . . . . . . . . . . . . . . . . . . 95
Safety Instructions (XA) . . . . . . . . . . . . . . . . . . . . . . . . 95
Endress+Hauser 3
Levelflex FMP50
Important document information

Symbols used Safety symbols
DANGER
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in serious or
fatal injury.
WARNING
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in serious or
fatal injury.
CAUTION
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in minor or
medium injury.
NOTICE
This symbol contains information on procedures and other facts which do not result in personal
injury.
Electrical symbols
Direct current
Alternating current
Direct current and alternating current
Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded via a grounding system.
Protective earth (PE)

Ground terminals that must be connected to ground prior to establishing any other connections.
The ground terminals are located on the inside and outside of the device.
• Interior ground terminal; protective earth is connected to the mains supply.
• Exterior ground terminal; device is connected to the plant grounding system.
Symbols for certain types of information and graphics

Permitted
Procedures, processes or actions that are permitted
Forbidden
Procedures, processes or actions that are forbidden
Tip
Indicates additional information
Reference to documentation
Reference to graphic
Notice or individual step to be observed

1. , 2. , 3.
Series of steps
Result of a step
1, 2, 3, ...
Item numbers
A, B, C, ...
Views
Temperature resistance of the connection cables
Specifies the minimum value of the temperature resistance of the connection cables
4 Endress+Hauser
Levelflex FMP50
Function and system design

Measuring principle General principles
The Levelflex is a "downward-looking" measuring system that functions according to the time-of-
flight method (ToF). The distance from the reference point to the product surface is measured. High-
frequency pulses are injected to a probe and led along the probe. The pulses are reflected by the
product surface, received by the electronic evaluation unit and converted into level information. This
method is also known as TDR (time domain reflectometry).
20 mA
100%
D
E
LN F
4 mA
0%
A0011360
1 Parameters for level measurement with guided wave radar

LN Probe length
D Distance
L Level
R Reference point of measurement
E Empty calibration (= zero)
F Full calibration (= span)
If the εr value is less than 7 in the case of rope probes, measurement is not possible in the area
of the tensioning weight (0 to 250 mm (0 to 9.84 in) from the probe end), (lower blocking
distance).
The reference point R of the measurement is located at the process connection.
Endress+Hauser 5
Levelflex FMP50
Dielectric constant
The dielectric constant (DC) of the medium directly affects the degree of reflection of the high-
frequency pulses. In the case of large DC values, such as with water or ammonia, there is strong
pulse reflection while, in the case of low DC values, such as with hydrocarbons, pulse reflection is
weak.
Input
The reflected pulses are transmitted from the probe to the electronics. Here, a microprocessor
evaluates the signals and identifies the level echo which was caused by the reflection of the high-
frequency pulses at the product surface. This clear signal detection system benefits from over 30
years of experience with pulse time-of-flight procedures that have gone into the development of the
PulseMaster® software.
The distance D to the product surface is proportional to the time of flight t of the impulse:
D = c · t/2,
with c being the speed of light.
Based on the known empty distance E, the level L is calculated:
L=E–D
The Levelflex has functions for interference echo suppression that can be activated by the user. They
guarantee that interference echoes from internal fixtures and struts, for example, are not interpreted
as level echoes.
Output
The Levelflex is preadjusted at the factory to the probe length ordered so that in most cases only the
application parameters that automatically adapt the device to the measuring conditions need to be
entered. For models with a current output, the factory adjustment for zero point E and span F is 4
mA and 20 mA, for digital outputs and the display module 0 % and 100 %. A linearization function
with max. 32 points, based on a table entered either manually or semi-automatically, can be
activated locally or remotely. This function allows the level to be converted into units of volume or
mass, for example.
6 Endress+Hauser
Levelflex FMP50
Life cycle of the product

Design
• Universal measuring principle
• Measurement is unaffected by product properties
• Hardware and software developed according to SIL IEC 61508
• Genuine, direct interface measurement
Procurement
• As the global market leader in level measurement, Endress+Hauser guarantees the security of
your investment
• Worldwide support and service
Installation
• No special tools are required
• Protection against reverse polarity
• Modern, detachable terminals
• Main electronics protected by a separate connection compartment
Commissioning
• Fast, menu-guided commissioning in just 6 steps
• Plain text display in local language reduces the risk of error or confusion
• Direct local access to all parameters
• Printed Brief Operating Instructions in the device onsite
Operation
• Multi-echo tracking: Reliable measurement thanks to self-learning echo search algorithms taking
into account the short-term and long-term history and plausibility of the detected signals to
suppress interference echoes.
• In accordance with NAMUR NE107
Maintenance
• HistoROM: Data backup for device settings and measured values
• Exact device and process diagnostics to assist fast decisions with clear information regarding
remedial action
• Intuitive, menu-guided operating concept in local language saves costs for training, maintenance
and operation
• Cover of the electronics compartment can also be opened in the hazardous area
Retirement
• Order code translation for subsequent models
• RoHS-compliant (Restriction of certain Hazardous Substances), unleaded soldering of electronic
components
• Environmentally friendly recycling approach
Measuring system General notes on probe selection

Rod probes should normally be used for liquids. Rope probes are used in liquids for measuring ranges
> 4 m (13 ft) or if the distance from the ceiling does not permit the installation of rigid probes.
Probe selection
FMP50
For level measurement in liquids
A0011387
2 Rod probe
Endress+Hauser 7
Levelflex FMP50
Rod probe
• Maximum probe length
4 m (13 ft)
• Material:
316L
A0011388
3 Rope probe with centering rod
Rope probe
• Maximum probe length
12 m (40 ft)
• Material:
316L
8 Endress+Hauser
Levelflex FMP50
Input
Measured variable The measured variable is the distance between the reference point and the product surface.
The level is calculated based on "E", the empty distance entered.
Optionally, the level can be converted to other variables (volume, mass) by linearization (32 points).
Measuring range The following table describes the media groups and the possible measuring range as a function of
the media group.
Levelflex FMP50
Measuring range
Typical
Media group εr Bare metallic Bare metallic
liquids
rod probes rope probes
1 1.4 to 1.6 Liquefied On request

gases, e.g.
N2, CO2
2 1.6 to 1.9 • Liquefied 4 m (13 ft) 12 m (39 ft)

gas, e.g.
propane
• Solvents
• Freon
• Palm oil
3 1.9 to 2.5 Mineral 4 m (13 ft) 12 m (39 ft)

oils, fuels
4 2.5 to 4 • Benzene, 4 m (13 ft) 12 m (39 ft)

styrene,
toluene
• Furan
• Naphthal
ene
5 4 to 7 • Chlorobe 4 m (13 ft) 12 m (39 ft)

nzene,
chlorofor
m
• Nitrocell
ulose
lacquers
• Isocyanat
e, aniline
6 >7 • Aqueous 4 m (13 ft) 12 m (39 ft)

solutions
• Alcohols
• Acids,
alkalis
The formation of buildup, particularly of moist products, can reduce the maximum possible
measuring range.
Endress+Hauser 9
Levelflex FMP50
Blocking distance The upper blocking distance (= UB) is the minimum distance from the reference point of the
measurement (mounting flange) to the maximum level.
R
SD UB
100%
E
F
LN
0%
A0011279
4 Definition of blocking distance and safety distance

LN Probe length
UB Upper blocking distance
E Empty calibration (= zero)
F Full calibration (= span)
SD Safety distance
Blocking distance (factory setting):

• For rod and rope probes up to 8 m (26 ft): 200 mm (8 in)
• For rod and rope probes over 8 m (26 ft): 0.025 × probe length
The specified blocking distances are factory-preset on delivery. These settings can be changed
depending on the application.
For rod and rope probes, the blocking distance can generally be reduced to 100 mm (4 in) for
media with DC > 7.
No blocking distance applies for applications in a bypass/stilling well.
A reliable measurement cannot be guaranteed within the blocking distance.
A safety distance SD can be defined in addition to the blocking distance. The device generates a
warning if the level rises to enter this safety distance.
Measuring frequency 100 MHz to 1.5 GHz

spectrum
10 Endress+Hauser
Levelflex FMP50
Output
Output signal HART
• Signal coding:
FSK ±0.5 mA over current signal
• Data transmission rate:
1 200 Bit/s
• Galvanic isolation:
Yes
Bluetooth® wireless technology
• Device version:
Order code 610 "Accessory mounted", option NF "Bluetooth"
• Operation / configuration:
Via the SmartBlue app
• Range under reference conditions:
> 10 m (33 ft)
• Encryption:
Encrypted communication and password encryption prevent incorrect operation by unauthorized
persons
PROFIBUS PA
• Signal coding:
Manchester Bus Powered (MBP)
31.25 kBit/s, Voltage mode
Yes
FOUNDATION Fieldbus
• Signal coding:
Manchester Bus Powered (MBP)
31.25 kBit/s, Voltage mode
Yes
Switch output
For HART devices, the switch output is available as an option.
• Function:
Open collector switch output
• Switching behavior:
Binary (conductive or non-conductive), switches when the programmable switch-on point/switch-
off point is reached
• Failure mode:
Non-conductive
• Electrical connection data:
U = 16 to 35 VDC, I = 0 to 40 mA
• Internal resistor:
RI < 880 Ω
The voltage drop at this internal resistor must be taken into account when planning the
configuration. For example, the resulting voltage at a connected relay must be sufficient to switch
the relay.
• Insulation voltages:
Floating, insulation voltage 1 350 VDC in relation to power supply and 500 VAC ground
• Switch point:
User-programmable, separate for switch-on point and switch-off point
• Switching delay:
User-programmable in the 0 to 100 s range, separate for switch-on point and switch-off point
Endress+Hauser 11
Levelflex FMP50
• Scan rate:
Corresponds to the measuring cycle
• Signal source / device variables:
• Level linearized
• Distance
• Terminal voltage
• Electronic temperature
• Relative echo amplitude
• Diagnostic values, advanced diagnostic blocks
• Only for active interface measurement
• Number of switch cycles:
Unlimited
Signal on alarm Depending on the interface, failure information is displayed as follows:

• Current output
• Choice of failure mode (in accordance with NAMUR Recommendation NE 43):
Minimum alarm: 3.6 mA
Maximum alarm (= factory setting): 22 mA
• Failure mode with user-configurable value: 3.59 to 22.5 mA
• Local display
• Status signal (as per NAMUR Recommendation NE 107)
• Plain text display
• Operating tool via digital communication (HART, PROFIBUS PA, FOUNDATION Fieldbus) or
service interface (CDI)
• Status signal (as per NAMUR Recommendation NE 107)
• Plain text display
Linearization The device's linearization function allows the user to convert the measured value to any length or
volume units. Linearization tables for calculating the volume in cylindrical vessels are
preprogrammed into the device. Other tables of up to 32 value pairs can be entered manually or
semi-automatically.
Galvanic isolation All circuits for the outputs are galvanically isolated from each other.
12 Endress+Hauser
Levelflex FMP50
Protocol-specific data HART
Manufacturer ID 17 (0x11)
Device type ID 0x1122
HART specification 7.0
Device description files (DTM, DD) Information and files under:

• www.endress.com
• www.fieldcommgroup.org
HART load min. 250 Ω
HART device variables The measured values can be freely assigned to the device variables.
Measured values for PV (primary variable)
• Distance
Measured values for SV, TV, QV (second, third and fourth variable)
• Distance
• Absolute echo amplitude
• Calculated εr value
Supported functions • Burst mode

• Additional transmitter status
Wireless HART data
Minimum starting voltage 17.5 V
Start-up current 4 mA
Starting time 80 s
Minimum operating voltage 17.5 V
Multidrop current 4.0 mA
Time for connection setup 30 s
Endress+Hauser 13
Levelflex FMP50
PROFIBUS PA
Manufacturer ID 17 (0x11)
Ident number 0x1558
Profile version 3.02
GSD file Information and files under:

• www.endress.com
GSD file version • www.profibus.org
Output values Analog Input:

• Distance
• Absolute echo amplitude
• Calculated εr value
Digital Input:
• Extended diagnostic blocks
• Status output PFS Block
Input values Analog Output:

• Analog value from PLC (for sensor block, external pressure and temperature)
• Analog value from PLC to be indicated on the display
Digital Output:
• Extended diagnostic block
• Level Limiter
• Sensor Block Measurement On
• Sensor Block Save History On
• Status output
Supported functions • Identification & Maintenance

Simple device identification via control system and nameplate
• Automatic Ident Number Adoption
GSD compatibility mode with predecessor Levelflex M FMP4x
• Physical Layer Diagnostics
Installation check of the PROFIBUS segment and the Levelflex M FMP4x using
terminal voltage and message monitoring
• PROFIBUS upload/download
Reading and writing parameters is up to ten times faster with PROFIBUS upload/
download
• Condensed status
Simplest and self-explanatory diagnostic information by categorizing diagnostic
messages that occur
FOUNDATION Fieldbus
Manufacturer ID 0x452B48
Device type 0x1028
Device revision 0x01
DD revision Information and files under:

• www.endress.com
CFF revision • www.fieldcommgroup.org
Device Tester Version (ITK version) 6.0.1
ITK Test Campaign Number IT085300
Link Master capability (LAS) Yes
Choice of "Link Master" and "Basic Device" Yes; Factory setting: Basic Device
Node address Factory setting: 247 (0xF7)
14 Endress+Hauser
Levelflex FMP50
Supported functions The following methods are supported:

• Restart
• ENP Restart
• Setup
• Linearization
• Self Check
Virtual Communication Relationships (VCRs)
Number of VCRs 44
Number of link objects in VFD 50
Permanent entries 1
Client VCRs 0
Server VCRs 10
Source VCRs 43
Sink VCRs 0
Subscriber VCRs 43
Publisher VCRs 43
Device Link Capabilities
Slot time 4
Min. delay between PDU 8
Max. response delay 20
Transducer Blocks
Block Contents Output values
Setup Transducer Block Contains all the parameters for standard • Level or volume (channel
commissioning 1)
(depending on the block
configuration)
• Distance (channel 2)
Advanced Setup Contains all the parameters for more accurate No output values
Transducer Block measurement configuration
Display Transducer Block Contains parameters to configure the onsite display No output values
Diagnostic Transducer Contains diagnostic information No output values

Block
Advanced Diagnostic Contains parameters for advanced diagnostics No output values

Transducer Block
Expert Configuration Contains parameters that require the user to have No output values
Transducer Block in-depth knowledge of the operation of the device in
order to configure the parameters appropriately
Expert Information Contains parameters that provide information about No output values
Transducer Block the state of the device
Service Sensor Contains parameters that can only be accessed by No output values
Transducer Block Endress+Hauser Service
Service Information Contains parameters that provide Endress+Hauser No output values

Transducer Block Service with information about the state of the
device
Data Transfer Contains parameters for backing up the device No output values
Transducer Block configuration in the display module and for writing
the saved configuration to the device. Access to
these parameters is reserved for Endress+Hauser
Service.
Endress+Hauser 15
Levelflex FMP50
Function blocks
Block Contents Number of Number of Execution Functionality
permanent instantiatable time
blocks blocks
Resource Block The Resource Block contains all 1 0 - Enhanced

the data that uniquely identify
the device. It is an electronic
version of a nameplate of the
device.
Analog Input The AI Block receives the 2 3 25 ms Enhanced

Block measuring data from the Sensor
Block (selectable via a channel
number), and makes the data
available to other blocks at its
output.
Discrete Input The Discrete Input Block receives 1 2 20 ms Standard

Block a discrete value (e.g. indicator
that measuring range has been
exceeded) and makes the value
available for other blocks at the
output.
Multiple The Multiple Analog Output 1 0 20 ms Standard

Analog Output Block is used to transmit analog
Block values from the bus to the device.
Multiple The Multiple Discrete Output 1 0 20 ms Standard

Discrete Block is used to transmit discrete
Output Block values from the bus to the device.
PID Block The PID Block is used as a 1 1 25 ms Standard

proportional-integral-derivative
controller and can be used
universally for closed-loop-
control in the field. It enables
cascade mode and feedforward
control.
Arithmetic The Arithmetic Block is designed 1 1 25 ms Standard

Block to permit simple use of popular
measurement math functions.
The user does not have to know
how to write equations. The
math algorithm is selected by
name, chosen by the user for the
function to be performed.
Signal The Signal Characterizer Block 1 1 25 ms Standard

Characterizer has two sections, each with an
Block output value that is a non-linear
function of the input value. The
non-linear function is generated
by a single look-up table with 21
arbitrary x-y pairs.
Input Selector The Input Selector Block 1 1 25 ms Standard

Block facilitates the selection of up to
four inputs and generates an
output value based on the
configured action. This block
normally receives its inputs from
AI Blocks. The block enables the
selection of maximum, minimum,
average and ‘first good’ values.
16 Endress+Hauser
Levelflex FMP50
Block Contents Number of Number of Execution Functionality

permanent instantiatable time
blocks blocks
Integrator The Integrator Block integrates a 1 1 25 ms Standard

Block variable as a function of the time
or accumulates the counts from a
Pulse Input Block. The Block can
be used as a totalizer that
totalizes until a reset, or as a
batch totalizer whereby the
integrated value is compared
against a target value generated
before or during the control
routine and generates a binary
signal when the target value is
reached.
Analog Alarm 1 1 25 ms Standard

Block
Up to 20 blocks can be instantiated in the device altogether, including the blocks already
instantiated.
Endress+Hauser 17
Levelflex FMP50
Power supply
Terminal assignment
Terminal assignment 2-wire: 4-20 mA HART
A B
+
1 1 -
2 2
+
-
1 3
A0036498
5 Terminal assignment 2-wire: 4-20 mA HART

A Without integrated overvoltage protection
B With integrated overvoltage protection
1 Connection 4-20 mA HART passive: terminals 1 and 2, without integrated overvoltage protection
2 Connection 4-20 mA HART passive: terminals 1 and 2, with integrated overvoltage protection
3 Terminal for cable screen
Block diagram 2-wire: 4-20 mA HART
3 4
2 5
1 6
+ + 1
I
- - 2
A0036499
6 Block diagram 2-wire: 4-20 mA HART

1 Active barrier with power supply (e.g. RN221N); observe terminal voltage
2 HART communication resistor (≥ 250 Ω); observe maximum load
3 Connection for Commubox FXA195 or FieldXpert SFX350/SFX370 (via VIATOR Bluetooth modem)
4 Analog display device; observe maximum load
5 Cable screen; observe cable specification
6 Measuring device
18 Endress+Hauser
Levelflex FMP50
Terminal assignment 2-wire: 4-20 mA HART, switch output
3
4
A B
+
3 3 -
4 4
+ +
- 1 -
2 1
+ 2
-
2
1 5
A0036500
7 Terminal assignment 2-wire: 4-20 mA HART, switch output

1 Connection 4-20 mA HART passive: terminals 1 and 2, without integrated overvoltage protection
2 Connection switch output (Open Collector): terminals 3 and 4, without integrated overvoltage protection
3 Connection switch output (Open Collector): terminals 3 and 4, with integrated overvoltage protection
4 Connection 4-20 mA HART passive: terminals 1 and 2, with integrated overvoltage protection
Block diagram 2-wire: 4-20 mA HART, switch output
3 4
2 5
1 6
+ + 1
I
- - 2
+ 3 Y
- 4
7
A0036501
8 Block diagram 2-wire: 4-20 mA HART, switch output

6 Measuring device
7 Switch output (Open Collector)
Endress+Hauser 19
Levelflex FMP50
Terminal assignment 2-wire: 4-20 mA HART, 4-20 mA
3
4
A B
+
3 3 -
4 4
+ +
- 1 -
2 1
+ 2
-
2
1 5
A0036500
9 Terminal assignment 2-wire: 4-20 mA HART, 4-20 mA

1 Connection current output 1, 4-20 mA HART passive: terminals 1 and 2, without integrated overvoltage
protection
2 Connection current output 2, 4-20 mA: terminals 3 and 4, without integrated overvoltage protection
3 Connection current output 2, 4-20 mA: terminals 3 and 4, with integrated overvoltage protection
4 Connection current output 1, 4-20 mA HART passive: terminals 1 and 2, with integrated overvoltage
protection
Block diagram 2-wire: 4-20 mA HART, 4-20 mA
3 4
2 5
1 6
+ + 1
I
- - 2
+ + 3 Y
- - 4
7
8
A0036502
 10 Block diagram 2-wire: 4-20 mA HART, 4-20 mA

6 Measuring device
8 Active barrier with power supply (e.g. RN221N), current output 2; observe terminal voltage
20 Endress+Hauser
Levelflex FMP50
Terminal assignment 4-wire: 4-20 mA HART (10.4 to 48 VDC)
1
2
L+
L- 3
4
+
-
2 3
1
A0036516
 11 Terminal assignment 4-wire: 4-20 mA HART (10.4 to 48 VDC)
1 Connection 4-20 mA HART (active): terminals 3 and 4

2 Connection supply voltage: terminals 1 and 2
Block diagram 4-wire: 4-20 mA HART (10.4 to 48 VDC)
3 4
2 5
1 6
+ 3
I
- 4
L+ 1
L- Y
2
7
A0036526
 12 Block diagram 4-wire: 4-20 mA HART (10.4 to 48 VDC)
1 Evaluation unit, e.g. PLC

6 Measuring device
7 Supply voltage; observe terminal voltage, observe cable specification
Endress+Hauser 21
Levelflex FMP50
Terminal assignment 4-wire: 4-20 mA HART (90 to 253 VAC)
1
2
L
N 3
4
+
-
2 3
1
A0036519
 13 Terminal assignment 4-wire: 4-20 mA HART (90 to 253 VAC)
1 Connection 4-20 mA HART (active): terminals 3 and 4

2 Connection supply voltage: terminals 1 and 2
LCAUTION
To ensure electrical safety:
‣ Do not disconnect the protective connection.
‣ Disconnect the supply voltage before disconnecting the protective earth.
Connect protective earth to the internal ground terminal (3) before connecting the supply
voltage. If necessary, connect the potential matching line to the external ground terminal.
In order to ensure electromagnetic compatibility (EMC): Do not only ground the device via the
protective earth conductor of the supply cable. Instead, the functional grounding must also be
connected to the process connection (flange or threaded connection) or to the external ground
terminal.
An easily accessible power switch must be installed in the proximity of the device. The power
switch must be marked as a disconnector for the device (IEC/EN61010).
22 Endress+Hauser
Levelflex FMP50
Block diagram 4-wire: 4-20 mA HART (90 to 253 VAC)
3 4
2 5
1 6
+ 3
I
- 4
L 1
N Y
2
7
A0036527
 14 Block diagram 4-wire: 4-20 mA HART (90 to 253 VAC)
1 Evaluation unit, e.g. PLC

5 Cable scree; observe cable specification
6 Measuring device
7 Supply voltage; observe terminal voltage, observe cable specification
Terminal assignment PROFIBUS PA / FOUNDATION Fieldbus
3
4
A B
+
3 3 -
4 4
+ +
- 1 -
2 1
+ 2
-
2
1 5
A0036500
 15 Terminal assignment PROFIBUS PA / FOUNDATION Fieldbus

1 Connection PROFIBUS PA / FOUNDATION Fieldbus: terminals 1 and 2, without integrated overvoltage
protection
2 Connection switch output (Open Collector): terminals 3 and 4, without integrated overvoltage protection
3 Connection switch output (Open Collector): terminals 3 and 4, with integrated overvoltage protection
4 Connection PROFIBUS PA / FOUNDATION Fieldbus: terminals 1 and 2, with integrated overvoltage protection
Endress+Hauser 23
Levelflex FMP50
Block diagram PROFIBUS PA / FOUNDATION Fieldbus
2 3
+ 1
I
- 2
1 + 3 Y
- 4
4
A0036530
 16 Block diagram PROFIBUS PA / FOUNDATION Fieldbus

1 Cable screen; observe cable specifications
2 Connection PROFIBUS PA / FOUNDATION Fieldbus
3 Measuring device
4 Switch output (open collector)
24 Endress+Hauser
Levelflex FMP50
Connection examples for the switch output

For HART devices, the switch output is available as an option.
3+
Ri +
-
4-
A0015909
 17 Connection of a relay
+
1
2
3+
Ri
4-
A0015910
 18 Connection to a digital input

1 Pull-up resistor
2 Digital input
For optimum interference immunity we recommend to connect an external resistor (internal

resistance of the relay or pull-up resistor) of < 1 000 Ω.
Endress+Hauser 25
Levelflex FMP50
Device plugs In device versions with a device plug (M12 or 7/8"), it is not necessary to open the housing in
order to connect the signal cable.
4 3
1 2
A0011175
 19 Pin assignment of M12 plug

1 Signal +
2 Not assigned
3 Signal –
4 Ground
1 3
2 4
A0011176
 20 Pin assignment of 7/8" plug

1 Signal –
2 Signal +
3 Not assigned
4 Shielding
26 Endress+Hauser
Levelflex FMP50
Power supply An external power supply is required.

Various supply units can be ordered from Endress+Hauser.
2-wire, 4-20mA HART, passive
2-wire; 4-20mA HART 1)

"Approval" 2) Terminal voltage U at the device Maximum load R, depending on the supply voltage U0 at the
supply unit
• Non-Ex 11.5 to 35 V 3) 4)
R [!]
• Ex nA
• Ex ic 500
• CSA GP
Ex ia / IS 11.5 to 30 V 4)
0
10 20 30 35 U0 [V]
11.5 22.5
A0035511
4) 5)
• Ex d / XP 13.5 to 30 V R [Ω]
• Ex ic[ia]
• Ex tD / DIP
500

0
U0 [V]
10 20 30
13.5 24.5
A0034969
1) Feature 020 of the product structure: option A

2) Feature 010 of the product structure
3) For ambient temperatures Ta≤ -30 °C (-22 °F) a minimum voltage of 14 V is required for the sartup of the device at the minimum error current
(3,6 mA). For ambient temperatures Ta ≥ 60 °C (140 °F) a minimum voltage of 12V is required for the sartup of the device at the minimum error
current (3,6 mA). The startup current can be parametrized. If the device is operated with a fixed current I ≥ 4,5 mA (HART multidrop mode), a
voltage of U ≥ 11,5 V is sufficient throughout the entire range of ambient temperatures.
4) If the Bluetooth modem is used, the minimum supply voltage increases by 2 V.
5) For ambient temperatures Ta ≤ -20 °C (-4 °F) a minimum voltage of 16 V is required for the startup of the device at the minimum error current
(3.6 mA).
Endress+Hauser 27
Levelflex FMP50
2-wire; 4-20 mA HART, switch output 1)

supply unit
• Non-Ex 13.5 to 35 V 3) 4) R [Ω]

• Ex nA
• Ex nA[ia]
500
• Ex ic
• Ex ic[ia]
• Ex d[ia] / XP
• Ex ta / DIP
• CSA GP
• Ex ia / IS 13.5 to 30 V 3) 4)
• Ex ia + Ex d[ia] / IS + XP 0
10 20 30 U0 [V]
13.5 24.5 35
A0034971
1) Feature 020 of the product structure: option B

3) For ambient temperatures Ta≤ -30 °C (-22 °F) a minimum voltage of 16 V is required for the startup of the device at the minimum error current
(3.6 mA).
2-wire; 4-20mA HART, 4-20mA 1)

supply unit
any Channel 1:
13.5 to 30 V 3) 4) 5) R [Ω]
500
0
U0 [V]
10 20 30
13.5 24.5
A0034969
Channel 2:
12 to 30 V R [!]
500
0
10 20 30 U0 [V]
12 23
A0022583
1) Feature 020 of the product structure: option C

3) For ambient temperatures Ta ≤ -30 °C (-22 °F) a minimum voltage of 16 V is required for the startup of the device at the minimum error current
(3.6 mA).
4) For ambient temperatures Ta ≤ -40 °C (-40 °F), the maximum terminal voltage must be restricted to U ≤ 28 V.
28 Endress+Hauser
Levelflex FMP50
Polarity reversal Yes

protection
Admissible residual ripple USS < 1 V

at f = 0 to 100 Hz
Admissible residual ripple USS < 10 mV

at f = 100 to 10000 Hz
Endress+Hauser 29
Levelflex FMP50
4-wire, 4-20mA HART, active
"Power supply; Output" 1) Terminal voltage Maximum load Rmax
K: 4-wire 90-253VAC; 4-20mA HART 90 to 253 VAC (50 to 60 Hz), overvoltage 500 Ω
category II
L: 4-wire 10,4-48VDC; 4-20mA HART 10.4 to 48 VDC
PROFIBUS PA, FOUNDATION Fieldbus
"Power supply; Output" 1) "Approval" 2) Terminal voltage

3)
E: 2-wire; FOUNDATION Fieldbus, switch output • Non-Ex 9 to 32 V
G: 2-wire; PROFIBUS PA, switch output • Ex nA
• Ex nA[ia]
• Ex ic
• Ex ic[ia]
• Ex d[ia] / XP
• Ex ta / DIP
• CSA GP
3)
• Ex ia / IS 9 to 30 V
• Ex ia + Ex d[ia] / IS + XP

3) Input voltages up to 35 V will not spoil the device.
Polarity sensitive No
FISCO/FNICO compliant Yes

according to IEC 60079-27
Power consumption "Power supply; Output" 1) Power consumption
A: 2-wire; 4-20mA HART < 0.9 W
B: 2-wire; 4-20mA HART, switch output < 0.9 W
C: 2-wire; 4-20mA HART, 4-20mA < 2 x 0.7 W
K: 4-wire 90-253VAC; 4-20mA HART 6 VA
L: 4-wire 10,4-48VDC; 4-20mA HART 1.3 W
Current consumption HART
Nominal current 3.6 to 22 mA, the start-up current for multidrop mode can be parametrized (is
set to 3.6 mA on delivery)
Breakdown signal adjustable: 3.59 to 22.5 mA

(NAMUR NE43)
PROFIBUS PA
Nominal current 14 mA
Failure current FDE (Fault 0 mA

Disconnection Electronic)
30 Endress+Hauser
Levelflex FMP50
FOUNDATION Fieldbus
Device basic current 15 mA
Failure current FDE (Fault 0 mA

Disconnection Electronic)
FISCO
Ui 17.5 V
Ii 550 mA
Pi 5.5 W
Ci 5 nF
Li 10 μH
Power supply failure • Configuration is retained in the HistoROM (EEPROM).

• Error messages (incl. value of operated hours counter) are stored.
Potential equalization No special measures for potential equalization are required.

If the device is designed for hazardous areas, observe the information in the documentation
"Safety Instructions" (XA).
Terminals • Without integrated overvoltage protection

Plug-in spring terminals for wire cross-sections 0.5 to 2.5 mm2 (20 to 14 AWG)
• With integrated overvoltage protection
Screw terminals for wire cross-sections 0.2 to 2.5 mm2 (24 to 14 AWG)
Cable entries Connection of the power supply and signal cables

To be selected in feature 050 "Electrical connection":
• Coupling M20, material depends on approval:
• For non-Ex, ATEX, IECEx, NEPSI Ex ia/ic:
Plastic M20x1.5 for cable ⌀5 to 10 mm (0.2 to 0.39 in)
• For Dust-Ex, FM IS, CSA IS, CSA GP, Ex ec:
• For Ex db:
No cable gland available
• Thread
• ½" NPT
• G ½"
• M20 × 1.5
• M12 plug / 7/8" plug
Only available for non-Ex, Ex ic, Ex ia
Connection of remote display FHX50
Feature 030 "Display, operation" Cable entry for connection of FHX50
L: "Prepared for display FHX50 + M12 connection" M12 socket
M: "Prepared for display FHX50 + M16 cable gland, custom connection" M12 cable gland
N: "Prepared for display FHX50 + NPT1/2 thread, custom connection" Thread NPT1/2
Cable specification • Devices without integrated overvoltage protection

Pluggable spring-force terminals for wire cross-sections 0.5 to 2.5 mm2 (20 to 14 AWG)
• Devices with integrated overvoltage protection
Screw terminals for wire cross-sections 0.2 to 2.5 mm2 (24 to 14 AWG)
• For ambient temperature TU≥60 °C (140 °F): use cable for temperature TU +20 K.
Endress+Hauser 31
Levelflex FMP50
HART
• A normal device cable suffices if only the analog signal is used.
• A shielded cable is recommended if using the HART protocol. Observe grounding concept of the
plant.
• For 4-wire devices: Standard device cable is sufficient for the power line.
PROFIBUS
Use a twisted, screened two-wire cable, preferably cable type A.
For further information on the cable specifications, see Operating Instructions BA00034S
"PROFIBUS DP/PA: Guidelines for planning and commissioning", PNO Guideline 2.092
"PROFIBUS PA User and Installation Guideline" and IEC 61158-2 (MBP).
FOUNDATION Fieldbus
Endress+Hauser recommends using twisted, shielded two-wire cables.
For further information on the cable specifications, see Operating Instructions BA00013S
"FOUNDATION Fieldbus Overview", FOUNDATION Fieldbus Guideline and IEC 61158-2 (MBP).
Overvoltage protection If the measuring device is used for level measurement in flammable liquids which requires the use of
overvoltage protection according to DIN EN 60079-14, standard for
test procedures 60060-1 (10 kA, pulse 8/20 μs), an overvoltage protection module has to be
installed.
Integrated overvoltage protection module

An integrated overvoltage protection module is available for 2-wire HART as well as PROFIBUS PA
and FOUNDATION Fieldbus devices.
Product structure: Feature 610 "Accessory mounted", option NA "Overvoltage protection".
Technical data
Resistance per channel 2 × 0.5 Ω max.
Threshold DC voltage 400 to 700 V
Threshold impulse voltage < 800 V
Capacitance at 1 MHz < 1.5 pF
Nominal arrest impulse voltage (8/20 μs) 10 kA
External overvoltage protection module

HAW562 or HAW569 from Endress+Hauser are suited as external overvoltage protection.
For detailed information please refer to the following documents:
• HAW562: TI01012K
• HAW569: TI01013K
32 Endress+Hauser
Levelflex FMP50
Performance characteristics
Reference operating • Temperature = +24 °C (+75 °F) ±5 °C (±9 °F)
conditions • Pressure = 960 mbar abs. (14 psia) ±100 mbar (±1.45 psi)
• Humidity = 60 % ±15 %
• Reflection factor ≥ 0.8 (metal plate for rod and rope probe with min. 1 m (40 in) diameter)
• Flange for rod or rope probe ≥ 300 mm (12 in) diameter
• Distance to obstacles ≥ 1 m (40 in)
Reference accuracy Typical data under reference operating conditions: DIN EN IEC 61298-2 / DIN EN IEC 60770-1;
percentage values in relation to the span.
Output: digital analog 1)
Accuracy (sum of non- ±2 mm (±0.08 in) ±0.02 %

linearity, non-repeatability
and hysteresis) 2)
Non-repeatability 3) ≤1 mm (0.04 in)
1) Add error of the analog value to the digital value.

2) If the reference conditions are not met, the offset/zero point resulting from the installation conditions can
be up to ±16 mm (±0.63 in). This additional offset/zero point can be compensated for by entering a
correction ("Level correction" parameter) during commissioning.
3) The non-repeatability is already considered in the accuracy.
Differing from this, the following measured error applies in the area of the lower probe end:
D
80 (3.15)
60 (2.36) DC = 2
40 (1.57)
DC = 80
20 (0.79)
0
-20 (-0.79)
-40 (-1.57)
-60 (-2.36)
-80 (-3.15)
0
50 (1.97)
100 (3.94)
150 (5.91)
250 (9.84)
300 (11.8)
A
20 (0.79)
200 (7.87)
40 (1.57)
80 (3.15)
A0021480
 21 Measured error at the probe end for rod and coax probes
A Distance from the probe end [mm(in)]
D Measured error: Sum of non-linearity, non-repeatability and hysteresis
Endress+Hauser 33
Levelflex FMP50
D
80 (3.15)
60 (2.36) DC = 80
40 (1.57)
20 (0.79)
0
-20 (-0.79)
-40 (-1.57)
-60 (-2.36)
-80 (-3.15)
50 (1.97)
100 (3.94)
150 (5.91)
200 (7.87)
300 (11.8)
A
0
20 (0.79)
250 (9.84)
A0021482
 22 Measured error at the probe end for rope probes

A Distance from the probe end [mm(in)]
D Measured error: Sum of non-linearity, non-repeatability and hysteresis
If the DC value is less than 7 in the case of rope probes, measurement is not possible in the area
of the tensioning weight (0 to 250 mm from the probe end), (lower blocking distance).
The following measured error applies in the area of the upper probe end:
R
D
40 (1.57)
30 (1.18) DC = 2
DC = 80
10 (0.39)
2 (0.08)
0 (0)
- 2 (- 0.08)
- 10 (-0.39)
- 30 (- 1.18)
- 40 (- 1.57)
100 (3.94) 200 (7.87)

A0015091
 23 Measured error at the upper probe end; engineering unit: mm (in)

D Sum of non-linearity, non-repeatability and hysteresis
DC Dielectric constant
Resolution • Digital: 1 mm
• Analog: 1 μA
34 Endress+Hauser
Levelflex FMP50
Response time The response time can be configured. The following step response times (in accordance with DIN EN
IEC 61298-2 / DIN EN IEC 60770-1) 1) are when damping is switched off:
Level measurement
Probe length Sampling rate Response time
< 12 m (39 ft) 3.6 measurements per second < 0.8 s
Influence of ambient The measurements are performed according to DIN EN IEC 61298-3 / DIN EN IEC 60770-1
temperature • Digital (HART, PROFIBUS PA, FOUNDATION Fieldbus): average TK = 0.6 mm/10 K
For devices with a remote sensor, 2) there is an additional offset error of
±0.3 mm/10K (±0.01 in/10K) per 1 m (3.3 ft) of the remote cable.
• Analog (current output):
• Zero point (4 mA): average TK = 0.02 %/10 K
• Span (20 mA): average TK = 0.05 %/10 K
1) According to DIN EN IEC 61298-2 / DIN EN IEC 60770-1, the step response time is the time that elapses after an abrupt change in the input
signal until the change in the output signal has adopted 90% of the steady-state value for the first time.
2) Product structure: feature 600, version MB, MC or MD)
Endress+Hauser 35
Levelflex FMP50
Installation
Installation conditions Suitable mounting position
1 2 3
A 4
A0012606
 24 Installation conditions for Levelflex
Spacing requirements when mounting

• Distance (A) between the vessel wall and rod and rope probes:
• For smooth metallic walls: > 50 mm (2 in)
• For plastic walls: > 300 mm (12 in) to metallic parts outside the vessel
• For concrete walls: > 500 mm (20 in), otherwise the permitted measuring range may be
reduced.
• Distance (B) between rod probes and internal fittings (3): > 300 mm (12 in)
• When using more than one Levelflex:
Minimum distance between the sensor axes: 100 mm (3.94 in)
• Distance (C) from the end of the probe to the bottom of the vessel:
• Rope probe: > 150 mm (6 in)
• Rod probe: > 10 mm (0.4 in)
36 Endress+Hauser
Levelflex FMP50
Additional conditions
• When mounting outdoors, a weather protection cover (1) can be used to protect the device against
extreme weather conditions.
• In metallic vessels, preferably do not mount the probe in the center of the vessel (2), as this would
lead to increased interference echoes.
If a central mounting position cannot be avoided, it is essential to perform interference echo
suppression (mapping) after commissioning the device.
• Do not mount the probe in the filling curtain (3).
• Avoid buckling the rope probe during installation or operation (e.g. as a result of product
movement against silo wall) by selecting a suitable mounting location.
In the case of freely suspended rope probes (probe end not fixed at the bottom), the distance
between the probe rope and internal fittings, which can change due to the movement of the
product, must never be less than 300 mm (12 in). Occasional contact between the probe end
weight and the cone of the vessel, however, does not influence the measurement provided that
the dielectric constant is at least DC = 1.8.
When the housing is mounted in a recess (e.g. in a concrete ceiling), observe a minimum
distance of 100 mm (4 in) between the cover of the connection compartment/electronics
compartment and the wall. Otherwise the connection compartment/electronics compartment
will not be accessible after installation.
Endress+Hauser 37
Levelflex FMP50
Mounting under confined conditions
Mounting with remote probe

The device version with a remote probe is suitable for applications with restricted mounting space. In
this case, the electronics housing is mounted at a separate position from the probe.
A B
6 Nm 6 Nm
(4.42 lbf ft) (4.42 lbf ft)
rmin = 100 (4) C

C
rmin = 100 (4)
6 Nm 6 Nm
(4.42 lbf ft) (4.42 lbf ft)
A0014794
A Angled plug at the probe

B Angled plug at the electronics housing
C Length of the remote cable as ordered
• Product structure, feature 600 "Probe design":

• Version MB "Sensor remote, 3m cable"
• Version MC "Sensor remote, 6m cable"
• Version MD "Sensor remote, 9m cable"
• The connecting cable is included in the delivery with these versions.
Minimum bending radius: 100 mm (4 inch)
• The mounting bracket for the electronics housing is included in the delivery with these versions.
Mounting options:
• Wall mounting
• Mounting on DN32 to DN50 (1-1/4 to 2 inch) post or pipe
• The connection cable has one straight plug and one plug angled at 90°. Depending on the local
conditions the angled plug can be connected at the probe or at the electronics housing.
The probe, electronics and connection cable are mutually compatible and bear a common serial
number. Only components with the same serial number may be connected to one another.
38 Endress+Hauser
Levelflex FMP50
Notes on the mechanical load of the probe
Tensile loading capacity of rope probes
FMP50
Rope 4mm (1/6") 316
2 kN
Lateral loading capacity (flexural strength) of rod probes
FMP50
Rod 8mm (1/3") 316L
10 Nm
Lateral load (bending moment) from flow conditions

The formula for calculating the bending moment M acting on the probe:
M = cw × ρ/2 × v2 × d × L × (LN - 0.5 × L)
With:
cw: coefficient of friction
ρ [kg/m3]: density of the medium
v [m/s]: flow velocity of the medium, perpendicular to the probe rod
d [m]: diameter of the probe rod
L [m]: level
LN [m]: probe length
Sample calculation
Coefficient of friction cw 0.9 (assuming turbulent flow - high Reynolds number)
Density ρ [kg/m3] 1000 (e.g. water)

Probe diameter d [m] 0.008
L = LN (unfavorable conditions)
LN
v L
d
A0014175
Bending torque [M] on rod probes, diameter 8mm (1/3”)

20.0
18.0
16.0
Bending torque [Nm]
max. bending torque
14.0
12.0
10.0
8.0
6.0
4.0
2.0
0.0 v=0.5m/s
0.4 0.8 1.2 1.6 2 2.4 2.8 3.2 3.6 4 v=0.7m/s
Probe length [LN] in meters v=1.0m/s
A0014182-EN
Endress+Hauser 39
Levelflex FMP50
Information concerning the process connection

Probes are mounted on the process connection with threaded connections or flanges. If there is
the danger with this installation that the probe end moves so much that it occasionally touches
the vessel floor or cone, the probe may need to be shortened at the lower end and fixed in place.
Threaded connection
A0015121
 25 Mounting with threaded connection; flush with the vessel ceiling
Seal
The thread and the type of seal comply with DIN 3852 Part 1, screwed plug, form A.
The following types of sealing ring can be used:
For thread G3/4": According to DIN 7603 with dimensions 27 mm × 32 mm
Use a sealing ring according to this standard in form A, C or D and of a material that offers
appropriate resistance for the application.
Refer to the dimensional drawing for the length of the screwed plug:
Nozzle mounting
!150 (6)
H
ø !150 (6)
A0015122
H Length of the centering rod or the rigid part of the rope probe
• Permissible nozzle diameter: ≤ 150 mm (6 in)

For larger diameters, the near-range measuring capability may be reduced.
For large nozzles, see the section "Mounting in nozzles ≥ DN300"
• Permissible nozzle height: ≤ 150 mm (6 in)
For larger heights, the near-range measuring capability may be reduced.
• The end of the nozzle should be flush with the tank ceiling in order to avoid ringing effects.
In thermally insulated vessels, the nozzle should also be insulated in order to prevent
condensate formation.
40 Endress+Hauser
Levelflex FMP50
Mounting in nozzles ≥ DN300

If installation in nozzles ≥ 300 mm (12 in) is unavoidable, installation must be carried out in
accordance with the following diagram in order to avoid interference signals in the near range.
1
3
2
A0014199
1 Lower edge of the nozzle

2 Approximately flush with the lower edge of the nozzle (±50 mm)
3 Plate, nozzle Ø 300 mm (12 in) = plate Ø 280 mm (11 in); nozzle Ø ≥ 400 mm (16 in) = plate Ø ≥
350 mm (14 in)
4 Pipe Ø 150 to 180 mm
Endress+Hauser 41
Levelflex FMP50
Securing the probe
Securing rope probes
B
2
A
A0012609
A Rope sag: ≥ 10 mm/(1 m probe length) [0.12 in/(1 ft probe length)]

B Reliably grounded end of probe
C Reliably insulated end of probe
1 Fastener in female thread of probe end weight
2 Insulated fastening kit
• The end of the rope probe must be secured (fixed down) under the following conditions:
If the probe would otherwise temporarily come into contact with the vessel wall, the cone, internal
fittings/beams or another part of the installation
• A female thread is provided in the probe weight to secure the end of the probe:
Rope 4 mm (1/6"), 316: M 14
• When fixed down, the end of the probe must be either reliably grounded or reliably insulated. Use
an insulated fastening kit if it is not otherwise possible to secure the probe with a reliably
insulated connection.
42 Endress+Hauser
Levelflex FMP50
Securing rod probes

• For WHG approval: A support is required for probe lengths ≥ 3 m (10 ft).
• In general, rod probes must be secured in the event of horizontal flow (e.g. from an agitator) or
strong vibrations.
• Only secure rod probes directly at the end of the probe.
øa
øb
!50 (1.97)
3
mm (in)
A0014127
1 Probe rod
2 Sleeve with narrow bore to ensure electrical contact between the sleeve and the rod.
3 Short metal pipe, e.g. welded in place
Probe Ø 8 mm (0.31 in)

• a < Ø 14 mm (0.55 in)
• b = Ø 8.5 mm (0.34 in)
NOTICE
Poor grounding of the probe end may cause incorrect measurements.
‣ Use a sleeve with a narrow bore to ensure good electrical contact between the sleeve and the
probe rod.
NOTICE
Welding can damage the main electronics module.
‣ Before welding: Ground the probe rod and remove the electronics.
Endress+Hauser 43
Levelflex FMP50
Special installation situations
Bypasses and stilling wells

The use of centering disks/stars/weights (available as accessories) is recommended in bypass
and stilling well applications.
A B
1 2
(3.94)
!100
3
A0014129
1 Mounting in stilling well

2 Mounting in bypass
3 Minimum distance between probe end and lower edge of bypass 10 mm (0.4 in)
• Pipe diameter: > 40 mm (1.6 in) (for rod probes).

• A rod probe can be installed in pipes with a diameter of up to 150 mm (6 in). The use of FMP51
with a coax probe is recommended for larger pipe diameters.
• Side outlets, holes, slots and welds - with a maximum inward projection of 5 mm (0.2 in) - do not
affect the measurement.
• There should not be any changes in the diameter of the pipe.
• The probe must be 100 mm (4 in) longer than the lower outlet.
• The probes must not touch the pipe wall within the measuring range. Support or brace the probe if
necessary. All rope probes are prepared for bracing in vessels (tensioning weight with anchor
hole).
For bypasses with condensate formation (water) and a medium with a low dielectric constant
(e.g. hydrocarbons):
Over time, the bypass fills with condensate up to the lower outlet. When levels are low, the
level echo is masked by the echo of the condensate as a result. In this range, the level of the
condensate is output and the correct value is only output when levels are higher. For this
reason, ensure that the lower outlet is 100 mm (4 in) below the lowest level to be measured
and fit a metal centering disk at the level of the lower edge of the lower outlet.
In thermally insulated vessels, the bypass should also be insulated in order to prevent
condensate formation.
Assignment of centering disk/centering star/centering weight to the pipe diameter
44 Endress+Hauser
Levelflex FMP50
Underground tanks
A0014142
In the case of nozzles with large diameters, use FMP51 with a coax probe to avoid reflections at the
nozzle wall.
Endress+Hauser 45
Levelflex FMP50
Mounting at an angle
LN
!
A0014145
• For mechanical reasons, the probe should be installed as vertically as possible.

• If the probe is installed at an angle, the length of the probe must be reduced depending on the
angle of installation.
• α 5 °: LNmax. 4 m (13.1 ft)
• α 10 °: LNmax. 2 m (6.6 ft)
• α 30 °: LNmax. 1 m (3.3 ft)
46 Endress+Hauser
Levelflex FMP50
Non-metal vessels
A0012527
1 Non-metal vessel
2 Metal sheet or metal flange
To ensure good measurement results when mounting on non-metal vessels, at the process
connection mount a metal sheet with a diameter of at least 200 mm (8 in) at a right angle to the
probe.
Endress+Hauser 47
Levelflex FMP50
Plastic and glass vessels: Mounting the probe on the outside wall
In the case of plastic and glass vessels, the probe can also be mounted on the outside wall under
certain conditions.
1
3
A0014150
1 Plastic or glass vessel

2 Metal plate with screw-in sleeve
3 No space between vessel wall and probe!
Requirements
• Dielectric constant of the medium: εr > 7.
• Non-conductive vessel wall.
• Maximum wall thickness (a):
• Plastic: < 15 mm (0.6 in)
• Glass: < 10 mm (0.4 in)
• No metal reinforcements on the vessel.
Note the following when mounting the device:
• Mount the probe directly on the vessel wall without any space between the wall and probe.
• To prevent any influence on the measurement, fit a plastic half pipe with a diameter of at least
200 mm (8 in), or a similar protective unit, on the probe.
• For vessel diameters less than 300 mm (12 in):
On the opposite side of the vessel, fit a grounding plate that is conductively connected to the
process connection and covers around half of the vessel's circumference.
• For vessel diameters of 300 mm (12 in) and higher:
At the process connection, fit a metal plate with a diameter of at least 200 mm (8 in) at a right
angle to the probe (see above).
48 Endress+Hauser
Levelflex FMP50
Vessel with thermal insulation

If process temperatures are high, the device must be included in normal vessel insulation (1) in
order to prevent the electronics heating up as a result of thermal radiation or convection. The
insulation may not go beyond the points labeled "MAX" in the drawings.
2 3
1
MAX MAX
A0014653
 26 Process connection with thread

1 Vessel insulation
2 Compact device
3 Sensor, remote
Endress+Hauser 49
Levelflex FMP50
Operating conditions: Environment

Ambient temperature Measuring device –20 to +80 °C (–4 to +176 °F)
Local display –20 to +70 °C (–4 to +158 °F), the readability of the display may be impaired at
temperatures outside the temperature range.
Connecting cable (for Max. 100 °C (212 °F)

"Sensor, remote" probe
design)
Remote display FHX50 –40 to 80 °C (–40 to 176 °F)
Remote display FHX50 –50 to 80 °C (–58 to 176 °F) 1)

(option)
1) This range applies if the option JN "Transmitter ambient temperature –50 °C (–58 °F)" has been selected in
order code 580 "Test, certificate". If the temperature is permanently below –40 °C (–40 °F), the chance of
failure increases.
For outdoor operation in strong sunlight:

• Mount the device in the shade.
• Avoid direct sunlight, particularly in warm climatic regions.
• Use a weather protection cover (see accessories).
Ambient temperature limits The following diagrams only consider functional aspects. Additional restrictions may apply for
certified device versions. See the separate Safety Instructions for more information.
50 Endress+Hauser
Levelflex FMP50
In the event of temperature (Tp) at the process connection, the permitted ambient temperature (Ta)
is reduced as indicated in the following diagram (temperature derating):
Temperature derating for FMP50 with threaded connection G¾ or NPT¾
[°C] ([°F])Ta
Ta
+80(+176)
Tp
A: 4...20 mA HART
-20(-4) Tp
-20 +80 [°C]
(-4) (+176) ([°F])
[°C] ([°F])Ta
GT20: +79 (+174) GT20
GT19: +74 (+165)
4...20 mA HART GT19: +73(+163)
C:
4...20 mA
K: 90...253 VAC
L: 10.4...48 VDC
-20(-4) Tp
-20 +74 +80 [°C]
(-4) (+165) (+176) ([°F])
[°C] ([°F])Ta
+76 (+169)
GT20: +76(+168)
G 1: PROFIBUS PA
FOUNDATION Fieldbus
-20(-4) Tp
-20 +76 +80 [°C]
(-4) (+169) (+176) ([°F])
[°C] ([°F])Ta
+74 (+164)
GT20: +73(+163)
2
G : PROFIBUS PA
FOUNDATION Fieldbus
Switch output
-20(-4) Tp
-20 +74 +80 [°C]
(-4) (+164) (+176) ([°F])
A0013944
GT19 = Plastic housing A = 1 current output Ta = Ambient temperature

GT20 = Aluminum housing C = 2 current outputs Tp = Temperature at the process
G1, G2 = PROFIBUS PA 1) connection
K, L = 4-wire
1) In the case of PROFIBUS PA and FOUNDATION Fieldbus, the temperature derating depends on whether
the switch output (terminals 3 and 4) is used (G2) or not (G1).
Endress+Hauser 51
Levelflex FMP50
Storage temperature • Permitted storage temperature: –40 to +80 °C (–40 to +176 °F)
• Use original packaging.
Climate class DIN EN 60068-2-38 (test Z/AD)
Altitude according to • Generally up to 2 000 m (6 600 ft) above MSL.

IEC61010-1 Ed.3 • Above 2 000 m (6 600 ft) if the following conditions are met:
• Ordering feature 020 "Power supply; Output" = A, B, C, E or G (2-wire versions)
• Supply voltage U < 35 V
• Supply voltage of overvoltage category 1
Degree of protection • When housing is closed, tested according to:

• IP68, NEMA6P (24 h at 1.83 m under water)
(also applies for the "Remote sensor" version)
• For plastic housing with see-through lid (display): IP68 (24 h at 1.00 m under water)
This restriction applies if the following options have been selected simultaneously in the product
structure: 030 ("Display/operation") = C ("SD02") or E ("SD03"); 040 ("Housing") = A ("GT19").
• IP66, NEMA4X
• With housing open: IP20, NEMA1
• Display module: IP22, NEMA2
Degree of protection IP68 NEMA6P only applies for M12 PROFIBUS PA plugs if the
PROFIBUS cable is plugged in and is also rated IP68 NEMA6P.
Vibration resistance DIN EN 60068-2-64 / IEC 60068-2-64: 20 to 2 000 Hz, 1 (m/s2)2/Hz
Cleaning the probe Dirt or buildup may form on the probe depending on the application. A thin, even layer has little
impact on the measurement. Thick layers can dampen the signal and then reduce the measuring
range. Very uneven deposit formation, e.g. caking due to crystallization, can result in incorrect
measurements. In such cases, we recommend the use of a non-contact measuring principle, or a
regular inspection of the probe for contamination.
Electromagnetic Electromagnetic compatibility in accordance with all of the relevant requirements outlined in the EN
compatibility (EMC) 61326 series and NAMUR Recommendation EMC (NE 21). For details, refer to the Declaration of
Conformity.
Download at www.endress.com.
Use a shielded cable for signal transmission.

Maximum measured error during EMC testing: < 0.5 % of the span.
When the probes are installed in metal and concrete vessels and when a coax probe is used:
• Interference emission according to EN 61326 - x series, Class B equipment.
• Interference immunity according to EN 61326 - x series, requirements for industry and NAMUR
Recommendation NE 21 (EMC)
When probes are installed without a shielding/metal wall, e.g. installation in plastic or wooden silos,
the effect of strong electromagnetic fields can influence the measured value.
• Interference emission according to EN 61326 - x series, Class A equipment.
• Interference immunity: the effect of strong electromagnetic fields can influence the measured
value.
52 Endress+Hauser
Levelflex FMP50
Process
Process temperature range The maximum temperature permitted at the process connection is determined by the O-ring version
ordered:
Device O-ring material Process temperature Approval
FMP50 FKM (Viton GLT) –20 to +80 °C (–4 to 176 °F) FDA
Process pressure range Device Process pressure
FMP50 –1 to 6 bar (–14.5 to 87 psi)
Dielectric constant (DC) Rod and rope probe: DC (εr) ≥ 1.6
Extension of the rope probes Elongation from temperature increase from 30 °C (86 °F) to 80 °C (176 °F): 1 mm / m rope length
due to temperature
Endress+Hauser 53
Levelflex FMP50
Mechanical construction
Dimensions Dimensions of the electronics housing
R110
99 (3.9)*
78 (3.07) 90 (3.54)
)
.17
6 (4
144 (5.67)
ø106 (4.17)
ø10
113.5 (4.47)
A0011346
 27 GT19 housing (plastic PBT). Unit of measurement mm (in)

*For devices with integrated overvoltage protection.
R110 98 (3.86)*
78 (3.07) 90 (3.54)
07)
(4.
ø112 (4.41)
145.5 (5.73)
3.5
141.5 (5.57)
ø108.5 (4.27)
ø10
61 (2.4)
A0020751
 28 Housing GT20 (aluminum coated). Unit of measurement mm (in)

*For devices with integrated overvoltage protection.
54 Endress+Hauser
Levelflex FMP50
Mounting bracket dimensions
A B
ø42...60
(1.65...2.36)
52 (2)
122 (4.8) 127...140
161 (6.34) (5...5.51)
162...175
(6.38...6.89)
(3.4)
(2.8)
86
70
A0014793
 29 Mounting bracket for electronics housing. Unit of measurement mm (in)

A Wall mounting
B Post mounting
With "remote sensor" device versions (see feature 060 in the product structure), the mounting
bracket is included in the scope of delivery. However, it can also be ordered separately as an
accessory (order number: 71102216).
Dimensions of connection piece for remote probe
122(4.8)
(2.05)
52
15 (0.6)
rmin = 100 (4)
ø10
(0. .2
4)
(2.4)
61
43 (1.7)
ø82.5
(3.25)
A0023856
 30 Connection piece for remote probe; length of connecting cable: as per order. Unit of measurement mm (in)
Endress+Hauser 55
Levelflex FMP50
FMP50: Dimensions of process connection/probe
(0.98)
69 (2.72)
25
36 mm
R
G¾
NPT¾
B C
7 mm 7 mm
ø4 (0.16)
LN
150 (5.91)
29.5 (1.16)
ø8 (0.31)
M14
ø22 (0.87)
A0012644
 31 FMP50: Process connection / probe. Unit of measurement mm (in)

A Thread ISO228 G3/4 or ANSI MNPT3/4 (feature 100)
B Rod probe 8mm or 1/3" (feature 060)
C Rope probe 4mm or 1/6" (feature 060)
LN Probe length
56 Endress+Hauser
Levelflex FMP50
Probe length tolerances Rod probes

Permitted tolerance depending on the probe length:
• < 1 m (3.3 ft) = –5 mm (–0.2 in)
• 1 to 3 m (3.3 to 9.8 ft) = –10 mm (–0.39 in)
• 3 to 6 m (9.8 to 20 ft) = –20 mm (–0.79 in)
• > 6 m (20 ft) = –30 mm (–1.18 in)
Rope probes
Permitted tolerance depending on the probe length:
• < 1 m (3.3 ft) = –10 mm (–0.39 in)
• 1 to 3 m (3.3 to 9.8 ft) = –20 mm (–0.79 in)
• 3 to 6 m (9.8 to 20 ft) = –30 mm (–1.18 in)
• > 6 m (20 ft) = –40 mm (–1.57 in)
Shortening probes If necessary, probes can be shortened by observing the following instructions:
Shortening rod probes

Rod probes must be shortened if the distance to the vessel base or outlet cone is less than
10 mm (0.4 in). To shorten, saw off the bottom end of the rod probe.
It is not possible to shorten FMP52 rod probes due to their coating.
Shortening rope probes

Rope probes must be shortened if the distance to the vessel base or outlet cone is less than
150 mm (6 in).
Endress+Hauser 57
Levelflex FMP50
Weight Housing
Part Weight
GT19 housing - plastic Approx. 1.2 kg
GT20 housing - aluminum Approx. 1.9 kg
FMP50
Part Weight Part Weight
Sensor Approx. 0.25 kg Rope probe 4 mm Approx. 0.1 kg/m probe length
Rod probe 8 mm Approx. 0.4 kg/m probe length
58 Endress+Hauser
Levelflex FMP50
Materials: GT19 housing

1
(plastic)
2.1
2.2
5.2
6
5.1
7
4 9 8
A0013788
No. Component part Material
1 Housing PBT
2.1 Electronics compartment cover • Sight glass: PC

• Rim: PBT-PC
• Cover seal: EPDM
• Thread coating: graphite-based lubricant varnish
2.2 Connection compartment cover • Cover: PBT

• Cover seal: EPDM
4 Safety device on housing neck • Screw: A4-70

• Clamp: 316L (1.4404)
5.1 Dummy plug, coupling, adapter or connector • Dummy plug, depending on device version:
(depending on device version) • PE
• PBT-GF
• Coupling, depending on device version:
• Brass (CuZn), nickel-plated
• PA
• Adapter: 316L (1.4404/1.4435)
• Seal: EPDM
• Connector M12: brass, nickel-plated 1)
• Connector 7/8": 316 (1.4401) 2)
5.2 Dummy plug, coupling or adapter (depending on • Dummy plug, depending on device version:
device version) • PE
• PBT-GF
• Steel, galvanized
• PA
• Adapter: 316L (1.4404/1.4435)
• Seal: EPDM
6 Dummy plug or M12 socket (depending on device • Dummy plug: brass (CuZn), nickel-plated
version) • M12 socket: GD-Zn, nickel-plated
7 Pressure compensation vent Brass (CuZn), nickel-plated
8 Ground terminal • Screw: A2

• Spring washer: A4
• Clamp: 304 (1.4301)
• Bracket: 304 (1.4301)
9 Adhesive nameplate Plastic
1) In the version with M12 connector, the seal material is Viton.

2) In the version with 7/8" connector, the seal material is NBR.
Endress+Hauser 59
Levelflex FMP50
Materials: GT20 housing

1
(die-cast aluminum, powder-
coated) 2.1
2.2
5.2
6
5.1
7
4 3 9 8
A0036037
1 Housing, RAL 5012 (blue) • Housing: AlSi10Mg(<0.1% Cu)

• Coating: polyester
2.1 Electronics compartment cover, RAL 7035 (gray) • Cover: AlSi10Mg(<0.1% Cu)
• Window: glass
• Cover seal: NBR
• Window seal: NBR
2.2 Connection compartment cover, RAL 7035 (gray) • Cover: AlSi10Mg(<0.1% Cu)
• Cover seal: NBR
3 Cover clamp • Screw: A4

• Clamp: 316L (1.4404)
4 Safety device on housing neck • Screw: A4-70

• Clamp: 316L (1.4404)
5.1 Dummy plug, coupling, adapter or connector • Dummy plug, depending on device version:
(depending on device version) • PE
• PBT-GF
• PA
• Adapter: 316L (1.4404/1.4435)
• Seal: EPDM
• M12 plug: brass, nickel-plated 1)
• 7/8" plug: 316 (1.4401) 2)
5.2 Dummy plug, coupling or adapter (depending on • Dummy plug, depending on device version:
device version) • PE
• PBT-GF
• Steel, galvanized
• PA
• Adapter: 316L (1.4404/1.4435)
• Seal: EPDM
6 Dummy plug or M12 socket (depending on device • Dummy plug: brass (CuZn), nickel-plated
version) • M12 socket: GD-Zn, nickel-plated
7 Pressure compensation vent Brass (CuZn), nickel-plated
60 Endress+Hauser
Levelflex FMP50
8 Ground terminal • Screw: A2

• Clamp: 304 (1.4301)
• Bracket: 304 (1.4301)
9 Adhesive nameplate Plastic
1) In the version with the M12 plug, the seal material is Viton (different from standard).
2) In the version with the 7/8" plug, the seal material is NBR (different from standard).
Endress+Hauser 61
Levelflex FMP50
Materials: Process Levelflex FMP50

connection
Threaded connection
No. Material
G¾, NPT¾
1 1 PPS-GF40
2 316L (1.4404)
2 3 PPS-GF40
3
A0013834
62 Endress+Hauser
Levelflex FMP50
Materials: Probe Levelflex FMP50
Feature 060 "Probe"

• AA: rod 8mm • LA: rope 4mm No. Material
• AB: rod 1/3" • LB: rope 1/6"
1 316L (1.4404)
2 316 (1.4401)
3 Setscrew: A4-70
1
1 4 Bracing screw: A2-70
2
4
A0036583 A0036584
Endress+Hauser 63
Levelflex FMP50
Materials: Mounting bracket
12
12
11
10
A0015143
Mounting bracket for "remote sensor" version
10 Holder 316L (1.4404)
11 Round bracket 316Ti (1.4571)
Screws/nuts A4-70
Distance sleeves 316Ti (1.4571) or 316L (1.4404)
12 Half-shells 316L (1.4404)
64 Endress+Hauser
Levelflex FMP50
Materials: Adapter and cable

for remote sensor
4 3
A0021722
Adapter and cable for "remote sensor" version
1 Cable FRNC
2 Sensor adapter 304 (1.4301)
3 Terminal 316L (1.4404)
Screw A4-70
4 Band 316 (1.4401)
Crimp sleeve Aluminum
Nameplate 304 (1.4301)
Endress+Hauser 65
Levelflex FMP50
Materials: Weather
protection cover 1
6
4
5
A0015473
No. Component: Material
1 Protection cover: 316L (1.4404)
2 Rubber molded part (4x): EPDM
3 Tensioning screw: 316L (1.4404) + carbon thread
4 Holder: 316L (1.4404)
5 Ground terminal
• Screw: A4
• Clamp: 316L (1.4404)
• Bracket: 316L (1.4404)
6 • Washer: A4
• Cylinder screw: A4-70
66 Endress+Hauser
Levelflex FMP50
Operability
Operating concept Operator-oriented menu structure for user-specific tasks
• Commissioning
• Operation
• Diagnostics
• Expert level
Operating languages
• English
• Deutsch
• Français
• Español
• Italiano
• Nederlands
• Portuguesa
• Polski
• русский язык (Russian)
• Svenska
• Türkçe
• 中文 (Chinese)
• 日本語 (Japanese)
• 한국어 (Korean)
• Bahasa Indonesia
• tiếng Việt (Vietnamese)
• čeština (Czech)
Feature 500 of the product structure determines which of these languages is preset on delivery.
Quick and save commissioning

• Interactive wizard with graphical interface for easy commissioning via FieldCare/DeviceCare
• Menu guidance with brief explanations of the individual parameter functions
• Standardized operation at the device and in the operating tools
Integrated data storage device (HistoROM)
• Enables transfer of configuration when changing electronic modules
• Records up to 100 event messages in the device
• Records up to 1000 measured values in the device
• Saves the signal curve on commissioning which can later be used as a reference.
Efficient diagnostics increase measurement reliability
• Remedy information is integrated in plain text
• Diverse simulation options and line recorder functions
Integrated Bluetooth module (option for HART devices)
• Easy and fast setup via SmartBlue (app)
• No additional tools or adapters required
• Signal curve via SmartBlue (app)
• Encrypted single point-to-point data transmission (Fraunhofer-Institut, third party, tested) and
password-protected communication via Bluetooth® wireless technology
Endress+Hauser 67
Levelflex FMP50
Local operation Operation Pushbuttons Touch Control

with
Order code for Option C "SD02" Option E "SD03"

"Display;
Operation"
A0036312 A0036313
Display 4-line display 4-line display

elements white background lighting; switches to red in
event of device error
Format for displaying measured variables and status variables can be individually configured
Permitted ambient temperature for the display: –20 to +70 °C (–4 to +158 °F)
The readability of the display may be impaired at temperatures outside the temperature
range.
Operating local operation with 3 push buttons (, , ) external operation via touch control; 3
elements optical keys: , , 
Operating elements also accessible in various hazardous areas
Additional Data backup function

functionality The device configuration can be saved in the display module.
Data comparison function

The device configuration saved in the display module can be compared to the current device
configuration.
Data transfer function

The transmitter configuration can be transmitted to another device using the display module.
Operation with remote

1 2
display and operating
module FHX50
A0036314
 32 FHX50 operating options

1 Display and operating module SD03, optical keys; can be operated through the glass of the cover
2 Display and operating module SD02, push buttons; cover must be removed
68 Endress+Hauser
Levelflex FMP50
Operation via Bluetooth® Requirements

wireless technology
1
2
A0036790
 33 Device with Bluetooth module

1 Electronics housing of the device
2 Bluetooth module
This operation option is only available for devices with Bluetooth module. There are the following
options:
• The device has been ordered with a Bluetooth module:
Feature 610 "Accessory Mounted", option NF "Bluetooth"
• The Bluetooth module has been ordered as an accessory (ordering number: 71377355) and has
been mounted. See Special Documentation SD02252F.
Operation via SmartBlue (app)
1 2 3
A0034939
 34 Operation via SmartBlue (app)

1 Transmitter power supply unit
2 Smartphone / tablet with SmartBlue (app)
3 Transmitter with Bluetooth module
Endress+Hauser 69
Levelflex FMP50
Remote operation Via HART protocol
2 3 6 8
1 4 5 7
A0036169
 35 Options for remote operation via HART protocol

1 PLC (Programmable Logic Controller)
2 Transmitter power supply unit, e.g. RN221N (with communication resistor)
3 Connection for Commubox FXA191, FXA195 and Field Communicator 375, 475
4 Field Communicator 475
5 Computer with operating tool (e.g. DeviceCare/FieldCare , AMS Device Manager, SIMATIC PDM)
6 Commubox FXA191 (RS232) or FXA195 (USB)
7 Field Xpert SFX350/SFX370
8 VIATOR Bluetooth modem with connecting cable
9 Transmitter
Via PROFIBUS PA protocol
2
3
1
PROFIBUS DP
PROFIBUS PA
T
4 4 4
A0036301
 36 Options for remote operation via PROFIBUS PA protocol

1 Segment coupler
2 Computer with Profiboard/Proficard and operating tool (e.g. DeviceCare/FieldCare
3 PLC (Progrommable Logic Controller)
4 Transmitter
5 Additional functions (valves etc.)
70 Endress+Hauser
Levelflex FMP50
Via FOUNDATION Fieldbus
IN
. -
FF-HSE BT
1
FF-H1 SB 2
PS BT
LD 4
3
BT
PS
FF-H1
BT
1
2
A0017188
 37 FOUNDATION Fieldbus system architecture with associated components

1 FFblue Bluetooth modem
2 Field Xpert SFX350/SFX370
3 DeviceCare/FieldCare
4 NI-FF interface card
IN Industrial network
FF-HSE High Speed Ethernet
FF-H1 FOUNDATION Fieldbus-H1
LD Linking Device FF-HSE/FF-H1
PS Bus Power Supply
SB Safety Barrier
BT Bus Terminator
Endress+Hauser 71
Levelflex FMP50
DeviceCare/FieldCare via service interface (CDI)
1
A0032466
 38 DeviceCare/FieldCare via service interface (CDI)

1 Service interface (CDI) of the instrument (= Endress+Hauser Common Data Interface)
2 Commubox FXA291
3 Computer with DeviceCare/FieldCare operating tool
72 Endress+Hauser
Levelflex FMP50
Integration in tank gauging The Endress+Hauser Tank Side Monitor NRF81 provides integrated communications for sites with
system multiple tanks, each with one or more sensors on the tank, such as radar, spot or average
temperature, capacitive probe for water detection and/or pressure sensors. Multiple protocols out of
the Tank Side Monitor guarantee connectivity to nearly any of the existing industry standard tank
gauging protocols. Optional connectivity of analog 4...20 mA sensors, digital I/O and analog output
simplify full tank sensor integration. Use of the proven concept of the intrinsically safe HART bus for
all on-tank sensors yields extremely low wiring costs, while at the same time providing maximum
safety, reliability and data availability.
1 2 3
4 5
8 6
7
A0016590
 39 The complete measuring system consists of:

1 Tankvision workstation
2 Commubox FXA195 (USB) - optional
3 Computer with operating tool (ControlCare) - optional
4 Level measuring device
5 Temperature measuring device
6 Tank Side Monitor NRF81
7 Pressure measuring device
8 Tankvision Tank Scanner NXA820
Endress+Hauser 73
Levelflex FMP50
SupplyCare inventory SupplyCare is a web-based operating program for coordinating the flow of material and information
management software along the supply chain. SupplyCare provides a comprehensive overview of the levels of
geographically distributed tanks and silos, for instance, providing complete transparency over the
current inventory situation, regardless of time and location.
Based on the measuring and transmission technology installed onsite, the current inventory data are
collected and sent to SupplyCare. Critical levels are clearly indicated and calculated forecasts provide
additional security for material requirements planning.
The main functions of SupplyCare:
Inventory visualization
SupplyCare determines the inventory levels in tanks and silos at regular intervals. It displays current
and historical inventory data and calculated forecasts of future demand. The overview page can be
configured to suit the user's preferences.
Master data management
With SupplyCare you can create and manage the master data for locations, companies, tanks,
products and users, as well as user authorization.
Report Configurator
The Report Configurator can be used to create personalized reports quickly and easily. The reports
can be saved in a variety of formats, such as Excel, PDF, CSV and XML. The reports can be
transmitted in many ways, such as by http, ftp or e-mail.
Event management
Events, such as when levels drop below the safety stock level or plan points, are indicated by the
software. In addition, SupplyCare can also notify pre-defined users by e-mail.
Alarms
If technical problems occur, e.g. connection issues, alarms are triggered and alarm e-mails are sent to
the System Administrator and the Local System Administrator.
Delivery planning
The integrated delivery planning function automatically generates an order proposal if a pre-set
minimum inventory level is undershot. Scheduled deliveries and disposals are monitored
continuously by SupplyCare. SupplyCare notifies the user if scheduled deliveries and disposals are not
going to be met as planned.
Analysis
In the Analysis module, the most important indicators for the inflow and outflow of the individual
tanks are calculated and displayed as data and charts. Key indicators of material management are
automatically calculated and form the basis for optimizing the delivery and storage process.
Geographical visualization
All the tanks and the tank inventories are represented graphically on a map (based on Google Maps).
The tanks and inventory situations can be filtered by tank group, product, supplier or location.
Multi-language support
The multi-language user interface supports 9 languages, thereby enabling global collaboration on a
single platform. The language and settings are recognized automatically using the browser settings.
SupplyCare Enterprise
SupplyCare Enterprise runs by default as a service under Microsoft Windows on an application server
in an Apache Tomcat environment. The operators and administrators operate the application via a
Web browser from their workstations.
74 Endress+Hauser
Levelflex FMP50
2
3
10
5 7 8
9
.
A0034288
 40 Example of inventory management platform with SupplyCare Enterprise SCE30B

1 SupplyCare Enterprise (via Web browser)
2 SupplyCare Enterprise installation
3 SupplyCare Enterprise on mobile devices (via Web browser)
4 Ethernet/WLAN/UMTS
5 Fieldgate FXA42
6 Power supply 24 V DC
7 Modbus TCP via Ethernet as server/client
8 Converter from Modbus to HART Multidrop
9 HART Multidrop
10 4 x 4 to 20 mA analog input (2-wire/4-wire)
Endress+Hauser 75
Levelflex FMP50
Cloud-based application: SupplyCare Hosting

SupplyCare Hosting is offered as a hosting service (software as a service). Here, the software is
installed within the Endress+Hauser IT infrastructure and made available to the user in the Endress
+Hauser portal.
1
3
WWW
4
10
5 7 8
9
.
A0034289
 41 Example of inventory management platform with SupplyCare Hosting SCH30

1 SupplyCare Hosting installation in Endress+Hauser data center
2 PC workstation with Internet connection
3 Warehouse locations with Internet connection via 2G/3G with FXA42 or FXA30
4 Warehouse locations with Internet connection with FXA42
5 Fieldgate FXA42
6 Power supply 24 V DC
7 Modbus TCP via Ethernet as server/client
8 Converter from Modbus to HART Multidrop
9 HART Multidrop
10 4 x 4 to 20 mA analog input (2-wire/4-wire)
With SupplyCare Hosting, users do not need to make the initial software purchase or install and run
the IT infrastructure needed. Endress+Hauser constantly update SupplyCare Hosting and enhance
the capability of the software in conjunction with the customer. The hosted version of SupplyCare is
thus always up-to-date and can be customized to meet different customer requirements. Other
services are also offered in addition to the IT infrastructure and the software that is installed in a
secure, redundant Endress+Hauser data center. These services include defined availability of the
global Endress+Hauser Service and Support Organization and defined response times in a service
event.
76 Endress+Hauser
Levelflex FMP50
Certificates and approvals

Currently available certificates and approvals can be called up via the product configurator.
CE mark The measuring system meets the legal requirements of the applicable EU Directives. These are listed
in the corresponding EU Declaration of Conformity along with the standards applied.
Endress+Hauser confirms successful testing of the device by affixing to it the CE mark.
RoHS The measuring system complies with the substance restrictions of the Restriction on Hazardous
Substances Directive 2011/65/EU (RoHS 2).
RCM-Tick marking The supplied product or measuring system meets the ACMA (Australian Communications and Media
Authority) requirements for network integrity, interoperability, performance characteristics as well
as health and safety regulations. Here, especially the regulatory arrangements for electromagnetic
compatibility are met. The products are labelled with the RCM- Tick marking on the name plate.
A0029561
Ex approval The devices are certified for use in hazardous areas and the relevant safety instructions are provided
in the separate "Safety Instructions" (XA, ZD) document. Reference is made to this document on the
nameplate.
The separate "Safety Instructions" documentation (XA) containing all the relevant explosion
protection data is available from your Endress+Hauser sales organization.
Dual seal according to The devices have been designed according to ANSI/ISA 12.27.01 as dual seal devices, allowing the
ANSI/ISA 12.27.01 user to waive the use and save the cost of installing external secondary process seals in the conduit
as required by the process sealing sections of ANSI/NFPA 70 (NEC) and CSA 22.1 (CEC) These
instruments comply with the North-American installation practice and provide a very safe and cost-
saving installation for pressurized applications with hazardous fluids.
Further information can be found in the Safety Instructions (XA) of the relevant devices.
Functional safety Use for level monitoring (MIN, MAX, range) up to SIL 3 (homogeneous redundancy), independently
evaluated by TÜV Rheinland in accordance with IEC 61508, refer to the "Functional Safety Manual"
SD00326F for more information.
Overfill prevention WHG

DIBt Z-65.16-501
Pressure equipment with Pressure instruments with a flange and threaded boss that do not have a pressurized housing do not
allowable pressure fall within the scope of the Pressure Equipment Directive, irrespective of the maximum allowable
≤ 200 bar (2 900 psi) pressure.
Reasons:
According to Article 2, point 5 of EU Directive 2014/68/EU, pressure accessories are defined as
"devices with an operational function and having pressure-bearing housings".
If a pressure instrument does not have a pressure-bearing housing (no identifiable pressure chamber
of its own), there is no pressure accessory present within the meaning of the Directive.
Radio approval Satisfies "Part 15" of the FCC rules for an unintentional radiator. All probes meet the requirements
for a Class A digital device.
In addition, coax probes and all probes in metal vessels meet the requirements for a Class B digital
device.
Endress+Hauser 77
Levelflex FMP50
Test, certificate Feature 580 "Test, certificate" Designation Approval
JA 3.1 Material documentation, wetted metal parts, EN10204-3.1 FMP50

inspection certificate
Test reports, declarations and inspection certificates are available in electronic format in the
W@M Device Viewer:
Enter the serial number that appears on the device (www.endress.com/deviceviewer)
This concerns the options for the following order codes:
• 550 "Calibration"
• 580 "Test, certificate"
Hard-copy product Hard-copy versions of the test reports, declarations and inspection certificates can also be order via
documentation order code 570 "Service", option I7 "Hard-copy product documentation". The documents are then
supplied with the product.
78 Endress+Hauser
Levelflex FMP50
Other standards and • EN 60529

guidelines Degrees of protection provided by enclosures (IP code)
• EN 61010-1
Safety requirements for electrical equipment for measurement, control and laboratory use
• IEC/EN 61326
"Emission in accordance with Class A requirements". Electromagnetic compatibility (EMC
requirements).
• NAMUR NE 21
Electromagnetic compatibility (EMC) of industrial process and laboratory control equipment
• NAMUR NE 43
Standardization of the signal level for the breakdown information of digital transmitters with
analog output signal.
• NAMUR NE 53
Software of field devices and signal-processing devices with digital electronics
• NAMUR NE 107
Status classification as per NE107
• NAMUR NE 131
Requirements for field devices for standard applications
• IEC61508
Functional safety of safety-related electric/electronic/programmable electronic systems
Endress+Hauser 79
Levelflex FMP50
Ordering information
Ordering information Detailed ordering information is available for your nearest sales organization
www.addresses.endress.com or in the Product Configurator under www.endress.com :
1. Click Corporate
2. Select the country
3. Click Products
4. Select the product using the filters and search field
5. Open the product page
The Configuration button to the right of the product image opens the Product Configurator.
Product Configurator - the tool for individual product configuration

• Up-to-the-minute configuration data
• Depending on the device: Direct input of measuring point-specific information such as
measuring range or operating language
• Automatic verification of exclusion criteria
• Automatic creation of the order code and its breakdown in PDF or Excel output format
• Ability to order directly in the Endress+Hauser Online Shop
80 Endress+Hauser
Levelflex FMP50
3-point linearity protocol The following points must be considered if option F3 (3-point linearity protocol) was selected in
feature 550 ("Calibration").
The 3 points of the linearity protocol are defined as follows, depending on the selected probe:
A
1 1
2 2
LN
B
3 3
C
A0021843
A Distance from the reference point R to the first measuring point

B Measuring range
C Distance from the probe end to the third measuring point
LN Probe length
1 First measuring point
2 Second measuring point (in the middle between the first and third measuring point)
3 Third measuring point
Rod probe Rope probe Rope probe

LN ≤ 6 m (20 ft) LN > 6 m (20 ft)
Position of 1st measuring A =350 mm (13.8 in) A =350 mm (13.8 in) A =350 mm (13.8 in)
point
Position of 2nd measuring In the middle between the 1st and In the middle between the 1st and 3rd In the middle between the 1st and 3rd
point 3rd measuring point measuring point measuring point
Position of 3rd measuring C = 250 mm (9.84 in) C = 500 mm (19.7 in) A+B = 5 500 mm (217 in)
point
Minimum measuring range B ≥ 400 mm (15.7 in) B ≥ 400 mm (15.7 in) B ≥ 400 mm (15.7 in)
Minimum probe length LN ≥ 1 000 mm (39.4 in) LN ≥ 1 250 mm (49.2 in) LN ≥ 1 250 mm (49.2 in)
The position of the measuring points can vary by ±1 cm (±0.04 in).
• In the case of rod and rope probes, the linearity check is performed with the entire device.
• The linearity check is performed under reference operating conditions.
Endress+Hauser 81
Levelflex FMP50
5-point linearity protocol The following points must be considered if option F4 (5-point linearity protocol) was selected in
feature 550 ("Calibration").
The 5 points of the linearity protocol are evenly distributed over the measuring range (0% - 100%).
Empty calibration (E) and Full calibration (F) must be specified in order to define the measuring
range 3).
The following restrictions must be considered when selecting E and F:
A
E
B
F
C
A0014673
A Distance from the reference point R to the 100% mark

B Measuring range
C Distance from the probe end to the 0% mark
E Empty calibration
F Full calibration
Sensor Minimum distance Minimum measuring

between reference point range
R and 100% mark
FMP50 A ≥ 250 mm (10 in) B ≥ 400 mm (16 in)
Probe type Minimum distance from Maximum value for

the probe end to the 0% "Empty calibration"
mark
Rod C ≥ 100 mm (4 in) E ≤ 3.9 m (12.8 ft)
Cable C ≥ 1 000 mm (40 in) E ≤ 11 m (36 ft)
• In the case of rod and rope probes, the linearity check is performed with the entire device.
• The linearity check is performed under reference operating conditions.
The selected values for Empty calibration and Full calibration are only used to create the
linearity protocol. Afterwards, the values are reset to the default values specific for the probe. If
values other than the default values are required, they must be ordered as a customized
parameterization →  83.
3) If (E) and (F) are not specified, probe-dependent default values will be used instead.
82 Endress+Hauser
Levelflex FMP50
Customer-specific If the option IJ: "Customized parameterization HART", IK "Customized parameterization PA" or IL
configuration "Customized parameterization FF" has been selected in feature 570 "Service", presettings that differ
from the default settings can be selected for the following parameters:
Parameter Communication Picklist / range of values

protocol
Setup → Unit of length • HART • in

• PA • ft
• FF • mm
• m
Setup → Empty calibration • HART 0 to 12 m (0 to 36 ft)

• PA
• FF
Setup → Full calibration • HART 0 to 12 m (0 to 36 ft)

• PA
• FF
Setup → Extended setup → Curr. output 1/2 → Damping HART 0 to 999.9 s
Setup → Extended setup → Curr. output 1/2 → Failure HART • Min

mode • Max
• Last valid value
Expert → Comm. → HART config. → Burst mode HART • Off

• On
Tagging (TAG) Ordering feature 895: Marking
Option Z1: Tagging (TAG), see additional spec.
Position of the measuring To be selected in the additional specifications:

point marking • Tag plate Stainless Steel
• Self-adhesive paper label
• Supplied label/plate
• RFID TAG
• RFID TAG + Tag plate Stainless Steel
• RFID TAG + Self-adhesive paper label
• RFID TAG + Supplied label/plate
Definition of the measuring To be defined in the additional specifications:

point designation 3 lines containing up to 18 characters each
The measuring point designation appears on the selected label and/or the
RFID TAG.
Designation in the Electronic The first 32 characters of the measuring point designation
Name Plate (ENP)
Designation on the display The first 12 characters of the measuring point designation
module
Endress+Hauser 83
Levelflex FMP50
Application packages
Heartbeat Diagnostics Availability
Available in all device versions.
Function
• Continuous self-monitoring of the device.
• Diagnostic messages output to
• the local display.
• an asset management system (e.g. FieldCare/DeviceCare).
• an automation system (e.g. PLC).
Advantages
• Device condition information is available immediately and processed in time.
• The status signals are classified in accordance with VDI/VDE 2650 and NAMUR recommendation
NE 107 and contain information about the cause of the error and remedial action.
Detailed description
See the "Diagnostics and troubleshooting" section of the Operating Instructions for the device.
84 Endress+Hauser
Levelflex FMP50
Heartbeat Verification Availability

Available for the following versions of feature 540 "Application package":
• EH: Heartbeat Verification + Monitoring
• EJ: Heartbeat Verification
Device functionality checked on demand

• Verification of the correct functioning of the measuring device within specifications.
• The verification result provides information about the condition of the device: Passed or Failed.
• The results are documented in a verification report.
• The automatically generated report supports the obligation to demonstrate compliance with
internal and external regulations, laws and standards.
• Verification is possible without interrupting the process.
Advantages
• No onsite presence is required to use the function.
• The DTM 4) triggers verification in the device and interprets the results. No specific knowledge is
required on the part of the user.
• The verification report can be used to prove quality measures to a third party.
• Heartbeat Verification can replace other maintenance tasks (e.g. periodic check) or extend the
test intervals.
SIL/WHG-locked devices 5)
• The Heartbeat Verification module contains a wizard for the proof test which must be performed
at appropriate intervals for the following applications:
• SIL (IEC61508/IEC61511)
• WHG (German Water Resources Act)
• To perform a proof test, the device must be locked (SIL/WHG locking).
• The wizard can be used via FieldCare, DeviceCare or a DTM-based process control system.
In the case of SIL-locked and WHG-locked devices, it is not possible to perform verification
without taking additional measures (e.g. bridging the output current) because the output
current must be simulated (Increased safety mode) or the level must be approached manually
(Expert mode) during subsequent re-locking (SIL/WHG locking).
SD01872F
4) DTM: Device Type Manager; controls device operation via DeviceCare, FieldCare or a DTM-based process control system.
5) Only relevant for devices with SIL or WHG approval: order code 590 ("Additional approval"), option LA ("SIL") or LC ("WHG").
Endress+Hauser 85
Levelflex FMP50
Heartbeat Monitoring Availability

Available for the following versions of feature 540 "Application package":
EH: Heartbeat Verification + Monitoring
Function
• In addition to the verification parameters, the corresponding parameter values are also logged.
• Existing measured variables, such as the echo amplitude, are used in the Foam detection and
Build-up detection wizards.
In the Levelflex FMP5x, the Foam detection and Build-up detection wizards cannot be used
together.
"Foam detection" wizard

• The Heartbeat Monitoring module contains the Foam detection wizard.
• This wizard is used to configure automatic foam detection, which detects foam on the product
surface on the basis of the reduced signal amplitude. Foam detection can be linked to a switch
output in order to control a sprinkler system, for example, which dissolves the foam.
• This wizard can be used via FieldCare, DeviceCare or a DTM-based process control system.
"Build-up detection" wizard

• The Heartbeat Monitoring module contains the Build-up detection wizard.
• The wizard is used to configure automatic buildup detection, which detects the buildup of deposits
on the probe on the basis of the reduced signal amplitude.
• This wizard can be used via FieldCare, DeviceCare or a DTM-based process control system.
Advantages
• Early detection of changes (trends) to ensure plant availability and product quality.
• Use of information for the proactive planning of measures (e.g. cleaning/maintenance).
• Identification of undesirable process conditions as the basis to optimizing the facility and the
processes.
• Automated control of measures to remove foam or buildup.
SD01872F
86 Endress+Hauser
Levelflex FMP50
Accessories
Device-specific accessories Weather protection cover
Accessory Description
Weather protection cover
222 (8.74)
A0015466
300 (11.8) 275 (10.8)

255.1 (10) 164 (6.46) 54
(2
.13
)
55
5)
(1.
4)
38
35°
65°
(6.1
15 6
A0015472
 42 Weather protection cover; Dimensions: mm (in)
 Enclosed",
The weather protection cover can be ordered together with the device (product structure, feature 620 "Accessory
option PB "Weather Protection Cover").
Alternatively, it can be separately ordered as an accessory; order code 71162242.
Endress+Hauser 87
Levelflex FMP50
Mounting bracket for electronics housing
Accessories Description
Mounting bracket for A B

electronics housing
ø42...60
(1.65...2.36)
52 (2)
122 (4.8) 127...140
161 (6.34) (5...5.51)
162...175
(6.38...6.89)
(3.4)
(2.8)
86
70
A0014793
 43 Mounting bracket for electronics housing; engineering unit: mm (in)

A Wall mounting
B Post mounting
 With "remote sensor" device versions (see feature 060 in the product structure), the mounting bracket is included in
the scope of delivery. However, it can also be ordered separately as an accessory (order number: 71102216).
88 Endress+Hauser
Levelflex FMP50
Mounting kit, insulated
Mounting kit, insulated

suitable for
FMP50
D
A0013586
 44 Scope of delivery of mounting kit:

1 Insulation sleeve
2 Eye bolt
To secure rope probes so that they are reliably insulated.

Maximum process temperature: 150 °C (300 °F)
For rope probes 4 mm (¹⁄₆ in) or 6 mm (1/4 in) with PA>steel :
• Diameter D = 20 mm (0.8 in)
• Order number: 52014249
For rope probes 6 mm (¹⁄₄ in) or 8 mm (1/3 in) with PA>steel:
• Diameter D = 25 mm (1 in)
• Order number: 52014250
Due to the risk of electrostatic charge, the insulation sleeve is not suitable for use
in hazardous areas! In this case, the probe must be secured so that it is reliably
grounded.
 The mounting kit can also be ordered directly with the device (Levelflex
product structure, feature 620 "Accessory enclosed", version PG "mounting kit,
insulated, rope").
Endress+Hauser 89
Levelflex FMP50
Centering star
Centering star PFA
10 (0.39)
•  16.4 mm (0.65 in)
•  37 mm (1.46 in)
suitable for
FMP50
A: ø16.4 (0.65)
B: ø37 (1.46)
A0014577
A For probe 8 mm (0.3 in)

B For probes 12 mm (0.47 in) and 16 mm (0.63 in)
The centering star is suitable for probes with a rod diameter of 8 mm (0.3 in),
12 mm (0.47 in) and 16 mm (0.63 in) (including coated rod probes) and can be
used in pipes from DN40 to DN50. See also Operating Instructions
BA00378F/00/A2.
• Material: PFA
• Permitted process temperature range: –200 to +250 °C (–328 to +482 °F)
• Order number
• Probe 8 mm (0.3 in) : 71162453
• Probe 12 mm (0.47 in): 71157270
• Probe 16 mm (0.63 in): 71069065
90 Endress+Hauser
Levelflex FMP50
Remote display FHX50
Remote display FHX50
2.
1.
4.
3.
A0019128
• Material:
• Plastic PBT
• 316L/1.4404
• Aluminum
• Degree of protection: IP68 / NEMA 6P and IP66 / NEMA 4x
• Suitable for display modules:
• SD02 (push buttons)
• SD03 (touch control)
• Connecting cable:
• Cable supplied with device up to 30 m (98 ft)
• Standard cable supplied by customer up to 60 m (196 ft)
• Ambient temperature range: –40 to 80 °C (–40 to 176 °F)
• Ambient temperature range (option): –50 to 80 °C (–58 to 176 °F) 1)
 • IfL, the remote display should be used, order the device version "Prepared for display FHX50" (feature 030, version
M or N). For the FHX50, you must select option A: "Prepared for display FHX50" under feature 050 "Measuring
device version".
• If the device version "Prepared for display FHX50" was not originally ordered and a FHX50 display is to be
retrofitted, you must select version B "Not prepared for display FHX50" under feature 050: "Measuring device
version" when ordering the FHX50. In this case, a retrofit kit for the device is supplied with the FHX50. The kit
can be used to prepare the device so that the FHX50 can be used.
 FHX50
Use of the FHX50 may be restricted for transmitters with an approval. A device can only be retrofitted with the
if the option L, M or N ("Prepared for FHX50") is listed under Basic specifications, item 4 "Display, operation"
in the Safety Instructions (XA) for the device.
Also pay attention to the Safety Instructions (XA) of the FHX50.
 Retrofitting is not possible on transmitters with:

• An approval for use in areas with flammable dust (dust ignition-proof approval)
• Ex nA type of protection
 For details, see document SD01007F.

1) This range is valid if option JN "Ambient temperature transmitter –50 °C (–58 °F)" has been selected in ordering feature 580 "Test, Certificate". If
the temperature is permanently below –40 °C (–40 °F), failure rates may be increased.
Endress+Hauser 91
Levelflex FMP50
Overvoltage protection
Overvoltage protection for

2-wire devices
OVP10 (1-channel)
OVP20 (2-channel)
A0021734
Technical data
• Resistance per channel: 2 × 0.5 Ωmax
• Threshold DC voltage: 400 to 700 V
• Threshold surge voltage: < 800 V
• Capacitance at 1 MHz: < 1.5 pF
• Nominal leakage current (8/20 μs): 10 kA
• Suitable for conductor cross-sections: 0.2 to 2.5 mm2 (24 to 14 AWG)
 Ordered with the device

Ideally, the overvoltage protection module should be ordered directly with the device. See product structure, feature
610 "Accessory mounted", option NA "Overvoltage protection". Separate order necessary only if retrofitting.
 Order numbers for retrofitting

• For 1-channel devices (feature 020, option A):
OVP10: 71128617
• For 2-channel devices (feature 020, options B, C, E or G)
OVP20: 71128619
Housing cover for retrofitting
In order to keep the necessary safety distances when using the surge arrester module, the housing cover also needs
to be replaced when the device is retrofitted. Depending on the housing type, the suitable cover can be ordered
using the following material number:
• Housing GT18: cover 71185516
 Restrictions in case of retrofitting

The use of the OVP module may be restricted depending on the transmitter approval. A device may only be
retrofitted with the OVP module if the option NA (overvoltage protection) is listed under Optional specifications in
the Safety Instructions (XA) associated with the device.
 For details, see SD01090F.
92 Endress+Hauser
Levelflex FMP50
Bluetooth module for HART devices
Accessory Description
Bluetooth module
A0036493
• Quick and easy commissioning via SmartBlue (app)

• No additional tools or adapters required
• Signal curve via SmartBlue (app)
• Encrypted single point-to-point data transmission (tested by Fraunhofer institue) and password protected
communication via Bluetooth® wireless technology
• Range under reference conditions:
> 10 m (33 ft)
 When using the Bluetooth module the minimum supply voltage increases by up to 3 V.
 Ordering with device
The Bluetooth module is preferably ordered with the device. See product structure, feature 610 "Accessory
Mounted", option NF "Bluetooth". A separate order is only necessary in case of retrofitting.
 Order code for retrofitting

Bluetooth module (BT10): 71377355
 Restrictions in case of retrofitting

Depending on the approval of the transmitter, application of the Bluetooth module may be restricted. A device may
only be retrofitted with a Bluetooth module if the option NF (Bluetooth) is listed in the associated Safety
Instructions (XA) under Optional specifications.
 For details refer to SD02252F.
Endress+Hauser 93
Levelflex FMP50
Communication-specific Commubox FXA195 HART

accessories For intrinsically safe HART communication with FieldCare via the USB interface
For details, see "Technical Information" TI00404F
Commubox FXA291
Connects Endress+Hauser field devices with a CDI interface (= Endress+Hauser Common Data
Interface) and the USB port of a computer or laptop
Order number: 51516983
For details, see "Technical Information" TI00405C
HART Loop Converter HMX50

Is used to evaluate and convert dynamic HART process variables to analog current signals or limit
values
Order number: 71063562
For details, see "Technical Information" TI00429F and Operating Instructions BA00371F
WirelessHART adapter SWA70

• Is used for the wireless connection of field devices
• The WirelessHART adapter can be easily integrated into field devices and existing infrastructures,
offers data protection and transmission safety and can be operated in parallel with other wireless
networks
For details, see Operating Instructions BA00061S
Connect Sensor FXA30/FXA30B

Fully integrated, battery-powered gateway for simple applications with SupplyCare Hosting. Up to 4
field devices with 4 to 20 mA communication (FXA30/FXA30B), serial Modbus (FXA30B) or HART
(FXA30B) can be connected. With its robust design and ability to run for years on the battery, it is
ideal for remote monitoring in isolated locations. Version with LTE (USA, Canada and Mexico only)
or 3G mobile transmission for worldwide communication.
For details, see "Technical Information" TI01356S and Operating Instructions BA01710S.
Fieldgate FXA42
Fieldgates enable communication between connected 4 to 20 mA, Modbus RS485 and Modbus TCP
devices and SupplyCare Hosting or SupplyCare Enterprise. The signals are transmitted either via
Ethernet TCP/IP, WLAN or mobile communications (UMTS). Advanced automation capabilities are
available, such as an integrated Web-PLC, OpenVPN and other functions.
For details, see "Technical Information" TI01297S and Operating Instructions BA01778S.
SupplyCare Enterprise SCE30B

Inventory management software that displays the level, volume, mass, temperature, pressure,
density or other parameters of tanks. The parameters are recorded and transmitted by means of
gateways like Fieldgate FXA42, Connect Sensor FXA30B or other gateway types.
This Web-based software is installed on a local server and can also be visualized and operated with
mobile terminals such as a smartphone or tablet.
For details, see Technical Information TI01228S and Operating Instructions BA00055S
SupplyCare Hosting SCH30

Inventory management software that displays the level, volume, mass, temperature, pressure,
density or other parameters of tanks. The parameters are recorded and transmitted by means of
gateways like Fieldgate FXA42, Connect Sensor FXA30B or other gateway types.
SupplyCare Hosting is offered as a hosting service (Software as a Service, SaaS). In the Endress
+Hauser portal, the user is provided with the data over the Internet.
For details, see Technical Information TI01229S and Operating Instructions BA00050S
Field Xpert SFX350

Field Xpert SFX350 is a mobile computer for commissioning and maintenance. It enables efficient
device configuration and diagnostics for HART and FOUNDATION Fieldbus devices in the non-Ex
area.
94 Endress+Hauser
Levelflex FMP50
Field Xpert SFX370

Field Xpert SFX370 is a mobile computer for commissioning and maintenance. It enables efficient
device configuration and diagnostics for HART and FOUNDATION Fieldbus devices in the non-Ex
area and the Ex area.
Service-specific accessories DeviceCare SFE100

Configuration tool for HART, PROFIBUS and FOUNDATION Fieldbus field devices
Technical Information TI01134S
FieldCare SFE500
FDT-based plant asset management tool
It can configure all smart field units in your system and helps you manage them. By using the status
information, it is also a simple but effective way of checking their status and condition.
Technical Information TI00028S
System components Memograph M graphic data manager

The Memograph M graphic data manager provides information on all the relevant process variables.
Measured values are recorded correctly, limit values are monitored and measuring points analyzed.
The data are stored in the 256 MB internal memory and also on a SD card or USB stick.
Technical Information TI00133R and Operating Instructions BA00247R
RN221N
Active barrier with power supply for safe separation of 4 to 20 mA standard signal circuits. Offers
bidirectional HART transmission.
Technical Information TI00073R and Operating Instructions BA00202R
RN221
Supply unit for powering two 2-wire measuring devices solely in the non-Ex area. Bidirectional
communication is possible via the HART communication jacks.
Technical Information TI00081R and Brief Operating Instructions KA00110R
Supplementary documentation
The following documentation types are available in the Downloads section of the Endress+Hauser
website (www.endress.com/downloads):
For an overview of the scope of the associated Technical Documentation, refer to the following:
• W@M Device Viewer (www.endress.com/deviceviewer): Enter the serial number from
nameplate
• Endress+Hauser Operations App: Enter the serial number from the nameplate or scan the
2D matrix code (QR code) on the nameplate
Brief Operating Instructions Guide that takes you quickly to the 1st measured value
(KA) The Brief Operating Instructions contain all the essential information from incoming acceptance to
initial commissioning.
Operating Instructions (BA) Your reference guide

These Operating Instructions contain all the information that is required in various phases of the life
cycle of the device: from product identification, incoming acceptance and storage, to mounting,
connection, operation and commissioning through to troubleshooting, maintenance and disposal.
Safety Instructions (XA) Depending on the approval, the following Safety Instructions (XA) are supplied with the device. They
are an integral part of the Operating Instructions.
The nameplate indicates the Safety Instructions (XA) that are relevant to the device.
Endress+Hauser 95
*71488020*
71488020
www.addresses.endress.com

Screenshot 2023-04-20 at 1.43.28 PM

Uploaded by

Copyright:

Available Formats

Screenshot 2023-04-20 at 1.43.28 PM

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Screenshot 2023-04-20 at 1.43.28 PM

Uploaded by

Copyright:

Available Formats

TI01000F/00/EN/23.

20 Products Solutions Services

Level measurement in liquids

Important document information . . . . . . . . . . . . . . . 4 Process pressure range . . . . . . . . . . . . . . . . . . . . . . . . . 53

Important document information

Direct current and alternating current

Protective earth (PE)

Symbols for certain types of information and graphics

Notice or individual step to be observed

Function and system design

1 Parameters for level measurement with guided wave radar

Life cycle of the product

Measuring system General notes on probe selection

3 Rope probe with centering rod

1 1.4 to 1.6 Liquefied On request

2 1.6 to 1.9 • Liquefied 4 m (13 ft) 12 m (39 ft)

3 1.9 to 2.5 Mineral 4 m (13 ft) 12 m (39 ft)

4 2.5 to 4 • Benzene, 4 m (13 ft) 12 m (39 ft)

5 4 to 7 • Chlorobe 4 m (13 ft) 12 m (39 ft)

6 >7 • Aqueous 4 m (13 ft) 12 m (39 ft)

4 Definition of blocking distance and safety distance

Blocking distance (factory setting):

Measuring frequency 100 MHz to 1.5 GHz

Signal on alarm Depending on the interface, failure information is displayed as follows:

Protocol-specific data HART

Device type ID 0x1122

HART specification 7.0

Device description files (DTM, DD) Information and files under:

HART load min. 250 Ω

Supported functions • Burst mode

Wireless HART data

Minimum starting voltage 17.5 V

Minimum operating voltage 17.5 V

Multidrop current 4.0 mA

Time for connection setup 30 s

Ident number 0x1558

Profile version 3.02

GSD file Information and files under:

Output values Analog Input:

Input values Analog Output:

Supported functions • Identification & Maintenance

Device type 0x1028

Device revision 0x01

DD revision Information and files under:

Device Tester Version (ITK version) 6.0.1

ITK Test Campaign Number IT085300

Link Master capability (LAS) Yes

Node address Factory setting: 247 (0xF7)

Supported functions The following methods are supported:

Virtual Communication Relationships (VCRs)

Number of link objects in VFD 50

Device Link Capabilities

Min. delay between PDU 8

Max. response delay 20

Diagnostic Transducer Contains diagnostic information No output values

Advanced Diagnostic Contains parameters for advanced diagnostics No output values

Service Information Contains parameters that provide Endress+Hauser No output values

Resource Block The Resource Block contains all 1 0 - Enhanced

Analog Input The AI Block receives the 2 3 25 ms Enhanced

Discrete Input The Discrete Input Block receives 1 2 20 ms Standard