SYSTEM

LUBRICATION
DUAL LINE
CATALOG No. 803/20

ADVANCED FLUID
MANAGEMENT SOLUTIONS
HELP THE NATURE
Packaging contains, depending on the articles,
one or more of the following materials; they
must be recycled in accordance with current
regulations in the country of use.
cardboard • polyethylene sack • polystyrene
paper • wood • nails • plastic strap
cellophane • clips • gummed paper
 ADVANCED FLUID
MANAGEMENT SOLUTIONS

DESIGN IS AN

Art
founded in 1975
the human side
of Quality
STUDY,
RESEARCH
AND DESIGN
The real strength of a firm starts with
the ability of its study and research
departments to always find the most
suitable solutions to address market
demands.

TESTING AND
INSPECTIONS
A sophisticated test room enables
careful testing of the quality of new
products before they are put on the
market.

ASSEMBLY
LINES
Dedicated equipment specially designed
to facilitate assembly operations, at the
same time allowing an effective and
automatic control of quality.
STORAGE OF
COMPONENTS
Our vertical stores enable quick and
careful preparation of the components
and spare parts intended for assembly
and sale.

TECHNOLOGY
INNOVATION
QUALITY
SAFETY
RELIABILITY

TECHNICAL
ASSISTANCE
RAASM has the most complete range
of products for lubrication and the
dispensing of fluids. The aim is to
always respond fully to the questions of
our customers and meet all their needs.
 SYSTEM 20 DUAL LINE

SERIES
C20S
page 12

SERIES
C20P
page 18

SERIES
C20F
page 24

8
The centralized dual-line lubrication systems are normally used In such systems the length of the piping can easily exceed 70
in large systems and machines: steel mills, cement works, mines, metres. In this system you can use oils with viscosity from 40 cSt
overhead cranes, shipyard cranes and presses, for example and greases up to NLGI 2.
the systems are sized in order to be able to reach rather high
pressures from 200 to 400 bar.

ADVANTAGES
■ Supplies an exact quantity of lubricant from ■ Visual check of each Volumetric distributors or by means of a
the pumping unit to all the grease points located special sensor.
even at great distances. ■ If a volumetric distributor does not work, all the other outlets
■ The dosing and measuring devices will continue to function normally.
(called Volumetric distributors) are managed through two main ■ Easy re-calibration of lubricant dosing of each distributor even
lines, therefore the lubricant is always under the control of the after installation.
system at the same time. ■ Optimum monitoring and control possibilities using
■ The system can be easily extended through the addition of appropriate equipment.
one or more Volumetric distributors. ■ The system keeps the pressure constantly regulated and is
■ This high pressure system allows the use of particularly able to compensate temperature fluctuations.
narrow pipes, enabling a reduction in the quantity and the ■ The system is able to generate only the necessary pressure
deterioration of the residual grease inside the piping, while required for each lubrication cycle, therefore the pump and
also reducing installation costs. other system components of the system are not subjected to
pressure variations that can affect their service life.

9
 ADVANCED FLUID
MANAGEMENT SOLUTIONS

2 0S
s C
rie
Se

www.raasm.com
 SERIES C20S
MOTOR-OPERATED
WITH RADIAL PISTONS
Compact motor-operated
pumps, equipped with line
inverter mounted on the main
body of the pump.
They have a sturdy and compact
base in nickel-plated aluminium
alloy, radially fitted with pumping
elements in galvanized hardened
steel. The epoxy powder painted
lubricant tank is available in 3
different sizes: 10, 30 and 70
litres. Two electric motors
(three-phase) are available
with 4 poles or 6 poles, to
which gearmotors with ratios
of 35:1 and 70:1 are coupled.
These all specifics allow a wide
combination of tanks, motors
and gear motors to meet all
end-users’ needs.

TECHNICAL CHARACTERISTICS
Max. delivery * 108 cm3/min
Max. working pressure 400 bar adjustable
Tank capacity 10-30-70 litres
Ratio of reducer in pump 35:1 - 70:1
Filling union F 1/2” G
Lubricant outlet union F 1/4” G
Pumping unit delivery P/N 2081100 - 1 cm3/cycle
Temperature -25 °C / +60 °C
Lubricant Oil > 40 cSt - Greases max NLGI 2
Electric min. level control Supplied
Electric min. max. level control On request
Power: 0,25 kW
230/400 V AC - 50 Hz - 275/480 V AC - 60 Hz *
Motor 6 poles motor: 870 ÷ 1100 rpm
4 poles motor: 1370 ÷ 1660 rpm
protection: IP 55
base: aluminum alloy
moving parts: steel
Materials
pumping piston: hardened steel
reservoir: painted steel
* Approx. delivery with grease NLGI 2 a 18 °C. (The lubricant must have technical characteristics in compliance with working temperature).
* Different rated voltages have to be indicated in the purchase order.
12

P/N Tank No. pumping Delivery
Reducer ratio Motor
Grease Oil capacity (litres) elements (cm3/min)
2070080 2070440 10 2 70:1 6 poles 28
2070200 2070560 30 2 70:1 6 poles 28
2070020 2070380 10 2 70:1 4 poles 40
2070140 2070500 30 2 70:1 4 poles 40
2070110 2070470 10 4 70:1 6 poles 56
2070230 2070590 30 4 70:1 6 poles 56
2070350 2070710 70 4 70:1 6 poles 56
2070050 2070410 10 4 70:1 4 poles 80
2070170 2070530 30 4 70:1 4 poles 80
2070290 2070650 70 4 70:1 4 poles 80
2070065 2070425 10 2 35:1 6 poles 54
2070185 2070545 30 2 35:1 6 poles 54
2070095 2070455 10 4 35:1 6 poles 108
2070215 2070575 30 4 35:1 6 poles 108
2070335 2070695 70 4 35:1 6 poles 108

STANDARD EQUIPMENT ON REQUEST

Low level capacitive sensor. Visual level indicator High level capacitive sensor.
for oil and grease.

OVERALL DIMENSIONS (mm)

►70
litres 10 litres
Grease Oil
330
Packing-m 3
1-0,152 1-0,152
Net weight kg 29,5 29,3
►30 Gross weight kg 41,3 41,1
litres
805
1051

►10
491

litres
30 litres
737

302

225 Grease Oil

225
548

Packing-m3 1-0,208 1-0,208

Net weight kg 34,7 34,4
Gross weight kg 46,9 46,6
198

279 637
420 70 litres
244 x ø 12,5

Grease Oil
Packing-m 3
1-0,296 1-0,296
Net weight kg 39,2 38,5
Gross weight kg 52 51,3
100

13
 Type of lubrication system with

P/N 39290 P/N 39289

Emergency stop Acoustic and
button (optional) flashing alarm
(optional)
Control equipment
(page 33)

Motor operated pump

S. C20S

Secondary line
with piping in
annealed copper
or flexible rubber

Overpressure Line and delivery filter

line inverter (page 31) (page 32)
14
MOTOR-OPERATED PUMP SERIES C20S

Volumetric distributor Line and pressure switch

Series VDL-M (page 28-29) (page 32)

Main line with

piping in steel or
flexible rubber

Lube point: In the plant are represented some

types of moving parts that need to be
lubricated

15
 ADVANCED FLUID
MANAGEMENT SOLUTIONS

2 0P
s C
rie
Se

www.raasm.com
 SERIES C20P
MOTOR-OPERATED PUMP
PISTONS WITH OSCILLATING UNIT
Motor-operated pumps
equipped with three-phase
motor (4-poles) with large
epoxy powder painted tank
(40 or 100 litres) mounted
on base in nickel-plated
aluminium alloy.
The pumping unit can be fitted
with dosing pistons of two
different diameters (7 or 10 mm),
thereby offering a choice of
different deliveries according to
customer requirements.
A minimum level sensor,
standard on all models, informs
the operator by means of a
special luminous signal and stops
pump operation, preventing it
from running empty.
The line inversion system is
supplied separately. It can
be electromechanical or
overpressure-type, as illustrated
on the following pages of this
catalog.

TECHNICAL CHARACTERISTICS
Doser piston flow rate * 160 (ø 7 mm) - 400 (ø 10 mm) cm3/min
Max. working pressure 400 bar adjustable
Tank capacity (litres) 40 -100 litres
Doser piston diameter 7 - 10 mm
Lubricant inlet connection F 1/2” G
Lubricant outlet connection F 3/8” G
Working temperature -25 °C / +60 °C
Lubricant Oil > 40 cSt - Greases max NLGI 2
Min level electric control Standard
Min and max level electric control On request
Power 0,55-0,66 kW
230/400 V AC-50 Hz - 275/480 V AC-60 Hz *
Motor
Speed 1370 ÷ 1640 rpm
Protection IP 55
* Approx. delivery with grease NLGI 2 a 18 °C. (The lubricant must have technical characteristics in compliance with working temperature).
* Different rated voltages have to be indicated in the purchase order.

18
 GUIDE TO CHOOSING PUMP
P/N Tank dosing piston ø Delivery
Grease Oil capacity (litres) (mm) (cm3/min)
2000065 2000305 40 7 160
2000185 2000425 100 7 160
2000095 2000335 40 10 400
2000215 2000455 100 10 400

STANDARD EQUIPMENT ON REQUEST

Low level capacitive sensor. Visual level indicator High level capacitive sensor.
for oil and grease.

OSCILLATING PUMPING UNIT

Dosing piston
(ø 7 mm - ø 10 mm)
The reciprocating motion of pumping Dosing piston
(ø 7 mm - ø 10 mm)
group’s body allows to the two dosing
pistons to dispense lubricant directly
from pumping group to pump’s outlet.

OVERALL DIMENSIONS (mm)

510

►100
litres
40 litres
►40
litres
Grease Oil
Packing-m 3
1-0,268 1-0,268
715
667

Net weight kg 63,2 61,3

538
490

ø 330
1031

Gross weight kg 79,6 77,7

899
361
316
148

100 litres
420 660,6
Grease Oil
777,2
Packing-m3 1-0,435 1-0,435
Net weight kg 75,7 73,6
Gross weight kg 92,5 90,4
255

360 x ø 12,5
19
 Type of lubrication system with

P/N 39290 P/N 39289

Emergency stop Acoustic and
button (optional) flashing alarm
(optional)
Control equipment
(page 33)

Motor operated pump Secondary line

S. C20P with piping in
annealed copper
or flexible rubber

Electric-motorized Overpressure Line and delivery filter

line inverter (page 30) line inverter (page 32)
(page 31)
20
MOTOR-OPERATED PUMPS SERIES C20P

Volumetric distributor Line and pressure switch

Series VDL-M (page 28-29) (page 32)

Main line with

piping in steel or
flexible rubber

Lube point: In the plant are represented some

types of moving parts that need to be
lubricated

21
 ADVANCED FLUID
MANAGEMENT SOLUTIONS

2 0F
s C
rie
Se

www.raasm.com
 SERIES C20F
AIR-OPERATED PUMP
10 LITRES DRUM
Depending on available feed
type, on system’s specifics
or on required dispense, an
air-operated pump may be
preferred to an electric one.
Various solutions are available for
great versatility: with 10 liters tank
or suitable for 20, 50 or 200 kg
drums, provided with drum cover
and grease follower plate
(if necessary).
If commercial drums are used,
once the lubricant is finished the
end user can replace the drum or
fill it up again through the specific
inlet, on request with a special kit.
Oil pumps are provided with drum
cover for open drums
(up to 50 kg) or with ring nut
for closed drums (usually
from 50 kg to 200 kg).
High compression ratio (50:1) and
adjustable feeding pressure allow
to set system’s pressure to its
specific requirements
(from 100 to 350 bar).

TECHNICAL CHARACTERISTICS
Max flow rate 1330 cm3/min
Max working pressure * 8 bar
Pressure ratio 50:1
Air inlet connection F 1/4” G
Lubricant outlet connection F 1/4” G
Overpressure valve adjustable from 100 to 350 bar
Operating temperature -25 °C / +60 °C
Lubricant Oil > 40 cSt - Grease max NLGI 2
* Approx. delivery with grease NLGI 2 at 18°C.

DELIVERY INVERSION AND CONTROL ASSEMBLY

Pressure gauge
This group is composed by:
- Pressure gauge: to check the line pressure.
- Overpressure valve: allows to check the 300 µm filling filter Bleeder valve
system pressure and to discharge the
lubricant in case of overpressure
100 - 350 bar.
- Filling filter: for filling the lubricant
in the tank. Pump body
- Bleeder valve: during the filling phase,
it allows to remove the air inside. Overpressure
Overpressure valve inverter
24
 GUIDE TO CHOOSING PUMP
P/N Tank capacity Drum internal ø Pump Pump outlet
Drum cover Follower plate
Grease (litres) (mm) (R 50:1) assembly
2010020 10 litres 220 62641 - 10/617 2080201
2010200 20 kg 255/300 62648 10/507 10/63 2080201
2010380 50 kg 335/360 62674 10/503 10/62 2080201
2010470 60 kg 360/400 62674 10/502 10/61 2080201
2010560 200 kg 540/580 62695 10/501 10/60 2080201

P/N Tank capacity Drum external ø Pump Pump outlet

Drum cover Drum ring
Oil (litres) (mm) (R 50:1) assembly
2010650 10 litres 240 62641 - - 2080201
2010830 20 kg 260/330 62648 10/507 - 2080201
2011010 50 - 60 kg 340/385 62674 10/503 - 2080201
2011100 50 - 60 kg closed - thread 2” 62674 level 39650 10/14 2080201
2011190 200 kg closed - thread 2” 62695 level 39650 10/14 2080201

DOTAZIONE STANDARD ON REQUEST

Only for Only for
10 litres model 10 litres modeld

Ultrasonic Visual high level Visual high level Charging filter for filling standard
min/max level indicator indicator indicator drums when empty
(union M 3/4” G) for oil for grease

OVERALL DIMENSIONS (mm)

Grease A B C
2010020 351 335 292
A

2010200 355 361 341

2010380 355 621 389
2010470 355 621 424
2010560 355 835 604
B

Oil A B C
B

292 2010650 351 335 292

2010830 355 361 341
2011010 355 621 389
250,5

2011100 355 621 424

2011190 355 835 604
C

10 litres 20 kg 50 kg 60 kg 220 kg
Grease Oil Grease Oil Grease Oil Grease Oil Grease Oil
Packing-m 3
1-0,056 1-0,056 2-0,094 2-0,094 2-0,086 2-0,086 2-0,086 2-0,050 2-0,115 2-0,060
Net weight kg 18,2 17,4 13,5 12,2 15,2 13,4 15,6 11,4 23,2 13,0
Gross weight kg 18,5 17,7 14,1 12,8 15,8 14,0 16,2 12,0 24,0 13,8
25
 Type of lubrication system with

P/N 39290 P/N 39289

Emergency stop Acoustic and
button (optional) flashing alarm
(optional)
Control equipment
(page 33)

Secondary line
with piping in
annealed copper
Air operated solenoid valve or flexible rubber
24 V DC - 110 V AC
230 V AC (page 37)
Air operated pump S. C20F

Overpressure Line and delivery filter

line inverter (page 31) (page 32)
26
AIR-OPERATED PUMPS SERIES C20F

Volumetric distributor Line and pressure switch

Series VDL-M (page 28-29) (page 32)

Main line with

piping in steel or
flexible rubber

Lube point: In the plant are represented some

types of moving parts that need to be
lubricated

27
 VDL-M
VOLUMETRIC DISTRIBUTOR

The volumetric distributor

VDL-M is very simple, efficient
and precise, and also allows
the adjustment of delivery
directly to the system
installation (page 8-9).
In the first stage of the lubrication
cycle the fluid pressure in line 1,
moving the first pilot piston and
then the dosing piston, sends
the lubricant to the user points
connected in delivery 2.
After the maximum pressure in
line 1 is reached, indicated by
the line end pressure switch, the
inverter changes the feed from
line 1 to line 2.
In the second stage, the
procedure is repeated as above:
the fluid pressure moving the first
pilot piston and then the dosing
piston, sends the lubricant to the
user points connected in
delivery 1.
The dispensing of lubricant
occurs alternately by pumping
through two separate main
circuits, each with its own
independent outlet.

TECHNICAL CHARACTERISTICS
Doser piston flow rate adjustable from 0,28 to 3,00 cm3/cycle
Notch to regulate flow rate 1-2-3
Flow rate for each notches 0,3 - 1,5 - 3,00 cm3/cycle
Max working pressure 150 bar (oil) - 400 bar (grease)
Min flow rate for each outlet 0,28 cm3/cycle
Max flow rate for each outlet 3,00 cm3/cycle
Lubricant Oil > 40 cSt - Greases max NLGI 2
No. of outlet 2 - 4 - 6 - 8 - 10
Lubricant inlet connection F 3/8” G
Lubricant outlet connection F 1/4” G
Working temperature -25 °C / +60 °C

28
 INSTALLATION ON MACHINERY DIRECT INSTALLATION ON
WITH ADDITIONAL PLATE MACHINERY
The distributor can be The distributor can be fixed
installed using the steel directly on the structure of
fixing plates subsequently the machinery, using the
welded on the machinery fixing holes with M8 screws.
or station fixed part. It is advisable to insert
spacer washers between
the distributor body and the
support surface, especially if
unfinished.

WORKING PRINCIPLE
Adjusting screw Lubricant in
Line 1 LINE INVERSION
delivery
Cycle lubricant No. 1
signalling piston inlet

BY THE INVERTER
WHEN MAX.
Distributor PRESSURE IS
Dosing piston body REACHED

Pilot piston Separator

Plug

LE DELIVER BLE DELIVE Double delivery

NG OU R Putting the hollow of
Y
SI

screw plugs facing

downwards, a double
delivery of lubricant Line 2
will be available from
Lubricant in the free outlet
lubricant
delivery inlet
No.2

Lubricant under pressure Lubricant in delivery

GUIDE TO CHOOSING DISTRIBUTOR

Outlet Threads *
P/N Abbreviation
Min Max Inlet Outlet
2030310 VDL-M2 1 2
2030330 VDL-M4 2 4
2030350 VDL-M6 3 6 F 3/8” G F 1/4” G
2030370 VDL-M8 4 8
2030390 VDL-M10 5 10
* Threads on request F 3/8” NPT - F 1/4” NPT

OVERALL DIMENSIONS (mm)

Abbreviation A B
VDL-M2 41 57
129,7
ø 13,5

VDL-M4 64 80
ø 8,5

VDL-M6 87 103
80
50

VDL-M8 110 126

VDL-M10 133 146

A 22,4
B 39,3
50

29
 OVERPRESSURE OR MOTOR-
OPERATED REVERSING VALVE

The reversing valves are

devices that enable the flow of
lubricant, at the pump outlet, to
be automatically diverted from
line 1 to line 2.
This operation allows the two
lines to be alternately pressurized,
thereby activating the distributors
connected to them. They
are available in two versions,
depending on the method of
operation: by overpressure and
motor-operated.
The overpressure reversing valves
exploit the pressure generated by
the pump in order to carry out the
change between the two lines,
whereas the motor-operated
reversing valves obtain the line
inversion by means of a servo
control fed by a gearmotor.

TECHNICAL CHARACTERISTICS
P/N 2080400
Max flow rate up to 7700 cm3/min (420 kg/h)
Max working pressure 150 bar (oil) - 400 bar (grease)

asynchronous three-phase 230/400V AC 50 Hz - 0,09 kW

Reducer * asynchronous three-phase 265/460V AC - 60 Hz - 0,09 kW
Speed 900÷1120 giri/min

Outlet connections line 1 and 2 F 1/2” G

Fluid inlet and discharging pressure outlet
F 1/2” G
connection
Protection IP55
Lubricant Oli > 40 cSt - Greases max NLGI 2
* Different rated voltages have to be indicated in the purchase order.

OVERALL DIMENSIONS (mm)

415,5

50 x 1/2”
158,5

172

86
96

50 x 1/2”
15 65 x ø 8,5 394
120 154 78
352

30
 OVERPRESSURE
REVERSING VALVES

The overpressure reversing valves

exploit the pressure generated by
the pump in order to carry out the
change between the two lines.

TECHNICAL CHARACTERISTICS
P/N 2080300 2080201
Max flow rate 6600 cm /min (360 kg/h)
3
5500 cm3/min (300 kg/h)
Max working pressure 50 - 150 bar (oil) - 50 - 400 bar (grease) 50 - 150 bar (oil) - 50 - 400 bar (grease)
Outlet connections line 1 and 2 F 3/8” G F 1/4” G
Working cycles max. 120 per min max. 120 per min
Fluid inlet and discharging pressure outlet
F 3/8” G F 1/4” G
connection
Lubricant Oil > 40 cSt - Greases max NLGI 2 Oil > 40 cSt - Greases max NLGI 2

OVERALL DIMENSIONS (mm)

186

136,5
90

10

60
28

50x3/8”
163 38
96
190 x ø 10,5
32 x 3/8”
20
60

40
136,5

70

210

31
 PRESSURE SWITCH
AND FILTER
PRESSURE SWITCH FILTER
Pressure switch
The line end pressure switches are
used to control and monitor the
correct operation of the centralized
system, confirming the reaching of
maximum pressure and end of cycle
control.
Filter
In order to ensure proper functioning
of the system and that the lubricant
intended for user points is totally
free of impurities, the installation
of appropriate filters at the control
unit inlet (for filling) and outlet is
recommended. The sturdy steel
structure the filters are provided with
ensures a sure seal and also allows
their use in centralized lubrication
systems where high operating
pressures (500 bar).
Working with lubricating oils and
greases, they are placed at the
outlet of the pumping unit and along
the line of the system.

TECHNICAL CHARACTERISTICS
Type Oil and Grease Oil and Grease
Max working pressure 400 bar 500 bar
Filtration degree - 30 - 60 - 100 - 150 - 300 µm
Lubricant inlet connection F 3/8”G F 3/8”G - F 1/2” G
Lubricant outlet connection - F 3/8”G - F 1/2” G
Electric contact by clamps -
Working temperature -25 °C / +60 °C -25 °C / +60 °C
Lubricant Oil > 40 cSt - Grease max NLGI 2 Oil > 40 cSt - Grease max NLGI 2

OVERALL DIMENSIONS (mm) Technical

Working
Protection
P/N pressure Type
characteristics degree
70 (bar)
2 pressure 2080700 from 30 IP55 without box
switches and
Hex 36 2080703 to 400 IP65 with box
2 manometers
1 pressure 2080710 from 30 IP55 without box
switches and
2 manometers 2080713 to 400 IP65 with box
71
ø 40

ø 40 23 x ø 6,5
65

Filtration
Lubricant P/N Connection
degree (µm)
DELIVERY-FILLING FILTER 2080900 30
2080930 F 3/8" G 60
Filter holder plug 2080950 100
Filter spring
2080800 150
Filter block Filter cartridge Oil F 3/8" G
2080801 300
F 3/8”G x F 3/8”G 30-60-100 and
F 1/2”G x F 1/2”G 150-300 µm Grease 2080901 30
2080931 F 1/2” G 60
Inlet Outlet 2080951 100
2080850 150
F 1/2” G
2080851 300
32
 CONTROL
EQUIPMENT
200÷500 V AC 50/60 Hz
System control board
The control equipment is
dedicated to the management and
control of centralized single-line
lubrication. The dedicated card
installed inside controls the inlet
and outlet signals of the whole
system.

TECHNICAL CHARACTERISTICS
P/N 2170031 2170021 2170033 2170036 2170026 2170037 2170035 2170025
Proper for pump C20S - C20P C20F C20S - C20P C20F C20S - C20P
Voltage 200÷500 V AC 200÷500 V AC 200÷500 V AC
Power consumed * 1500 W max 1500 W max 1500 W max
Button start /stop NO NO NO YES YES YES YES YES
Light allarm NO NO NO YES YES YES YES YES
Light filling NO NO NO YES YES YES NO NO
Tank full light NO NO NO YES YES YES NO NO
Trasparent window NO NO NO YES YES YES YES YES
Filling control NO NO YES YES YES YES NO NO
Protection rating IP54 IP55 IP55
Working temperature - 25°C / +60 °C - 25°C / +60 °C - 25°C / +60 °C
* Depends on the type of motor applied to the pump.
The card is installed in a metal box provided with or
without transparent window and communicates with a
INPUT AND OUTPUT SIGNALS
display integrated into an easy to use flexible membrane Input signals Output signals
keyboard. Within the enclosure all the components
(connections, remote control switches, fuses, etc.) are Start/Stop remote
Power motor pump
easy accesable. Cycle-counter/Pressure switch L1
- Display integrated into the flexible membrane keyboard Cycle-counter/Pressure switch L2 Power
- Simple user interface based on a menu, easy to start - motor inverter
Low level tank
configure and programme - pressure discharge valve
Safety pressure switch - solenoid inverter 1
- Rugged and waterproof cover, meets the requirements
maximum pressure
of IP55 Power relay
- Ability to customize the lubrication intervals, Thermal protection solenoid inverter 2
pause and the cycle count three-phase motors
- Programming of the operating parameters protected Remote operation lamp
Remote stand by cycle
by password
- Call system filling tank (on request) with high level light Micro-inverter L1
Remote warning lamp
indicator. Micro-inverter L2
Remote emergency
button

OVERALL DIMENSIONS (mm)

300 250 260

ø9

Packing-m3 1-0,03
Net weight kg 15,2-15,4
400

360

Gross weight kg 15,5-15,7

3333
 CONTROL
EQUIPMENT
12-24 V DC 120-230 V AC 50/60 Hz
This unit of management and
control is composed of an
electrical panel in polycarbonate in
reduced dimensions.
Inside is connected an electronic
card that communicates with a
display integrated in the practice
flexible membrane keypad located
on the front of the unit.

TECHNICAL CHARACTERISTICS
P/N 1670035 1670036
Proper for pump C20F C20F
Voltage 12/24 V DC 120-230 V AC 60/50 Hz
Power consumed 200 W max 600 W max
Inlet 9 9
Outlet 5 5
Protection rating IP64 IP64
Working temperature - 25°C / +60 °C - 25°C / +60 °C

The dedicated card installed inside controls the inlet

and outlet signals of the whole system.
INPUT AND OUTPUT SIGNALS
The hardware part is composed of the removable
terminal blocks located inside of the unit to facilitate Input signals Output signals
removal of the card in case of maintenance Start/Stop remote
Power motor pump
Cycle-counter/Pressure switch L1
- Display integrated into the flexible membrane
keyboard Cycle-counter/Pressure switch L2 Power
- Simple user interface based on a menu, Low level tank - pressure discharge valve
easy to start, and use configure and programme - solenoid inverter 1
Safety pressure switch
- Rugged and waterproof cover, meets the maximum pressure
requirements of IP64 Power relay
solenoid inverter 2
- Ability to customize the lubrication intervals, pause Thermal protection
and the cycle count three-phase motors
- Programming of the operating parameters protected Remote operation lamp
Remote stand by cycle
by password
Micro-inverter L1
Remote warning lamp
Micro-inverter L2

OVERALL DIMENSIONS (mm)

124
108 106

Packing-m3 1-0,005
185
166

Net weight kg 1,2-1,4

Gross weight kg 1,1-1,3

34
 ACCESSORIES PUMP
SERIES C20S

P/N 1581800
High or low level
capacitive sensor.

P/N 2081030
Pressure gauge.

P/N 2080201
Overpressure
reversing valve.

P/N 2081100
Pumping element.

P/N Description Connection Capacity/Pressure

1581800 Minimum and maximum capacitive level M 18 x 1 -
2081030 Pressure gauge ø 63 mm 600 bar M 1/4” G 600 bar
2080201 Overpressure reversing valve outlet F 1/4” BSP 5500 cm3/min (50-150 bar oil) (50 - 400 bar grease)
2081100 Pumping element ø 12 mm M27 x 1,5 1 cm3/cycle
35
 ACCESSORIES PUMP
SERIES C20P

P/N 1581800
High or low level
capacitive sensor.

P/N 2081050
Pressure gauge.

P/N 2081700
Outlet pressure
control device.

P/N 2081750
Base for pump and
connecting hoses.

P/N Description Connection Capacity/Pressure

1581800 Minimum and maximum capacitive level M 18 x 1 -
2081050 Pressure gauge ø 100 mm 600 bar M 1/4” G 600 bar
2081700 Outlet pressure control device outlet F 3/8” BSP 50 - 400 bar
2081750 Base for pump and connecting hoses hoses F 3/8”G x F 3/8”G hoses 400 bar

36
 ACCESSORIES PUMP
SERIES C20F

P/N 1581150
Filling filter 300 µm.

P/N 1582000 - 1582001

Air operated solenoid
24 V DC.
P/N 1582002 - 1582003
Air operated solenoid
110 V AC.
P/N 1582004 - 1582005
Air operated solenoid
230 V AC.

P/N 1581850
Min and max level
ultrasonic sensor.

P/N 39650 P/N 2080201

Min level indicator Overpressure
(optional only for oil). reversing valve.

P/N Description Connection Pressure P/N Description Connection Pressure

Air operated
1581150 Filling filter M 3/8” G - 1582004 solenoid 230 V AC
F 1/4”G x F 1/4”G 2,5-8 bar
Air operated Air operated
1582000 solenoid 24 V DC
F 1/4”G x F 1/4”G 2,5-8 bar 1582005 solenoid 230 V AC
F 1/2”G x F 1/2”G 2,5-8 bar
Air operated Min and max level wole on drum
1582001 solenoid 24 V DC
F 1/2”G x F 1/2”G 2,5-8 bar 1581850 ultrasonic sensor cover ø 31 mm
-
Air operated Overpressure 50-150 bar oil
1582002 solenoid 110 V AC
F 1/4”G x F 1/4”G 2,5-8 bar 2080201 reversing valve
outlet F 1/4” BSP
50-400 bar grease
Air operated Min level indicator
1582003 solenoid 110 V AC
F 1/2”G x F 1/2”G 2,5-8 bar 39650 (optional only for oil)
Oil -

37
 ACCESSORIES FOR VOLUMETRIC
DISTRIBUTOR SERIES VDL-M

P/N 2080100 - 2080101

P/N 2080102 - 2080103
P/N 2080104
Fixing plate for
volumetric
distributor “VDL-M”.

P/N 2080051
Distributor junction.

P/N Description Connection

2080100 Fixing plate for volumetric distributor “VDL-M” 2 outlet
2080101 Fixing plate for volumetric distributor “VDL-M” 4 outlet
2080102 Fixing plate for volumetric distributor “VDL-M” 6 outlet
2080103 Fixing plate for volumetric distributor “VDL-M” 8 outlet
2080104 Fixing plate for volumetric distributor “VDL-M” 10 outlet
2080051 Distributor junction “VDL-M” Dosing screw M 1/4” BSP
38
 System System System
20 20 20

C20F
C20P
C20S
dual line dual line dual line

Series
Series
Series
Grease Grease
Grease

G
(max

G
(max

G
(max NLGI 2)
NLGI 2) NLGI 2)

type
type
Oil

type
O
Lubricant
(> 40 cSt)

Lubricant

O
Oil Oil (> 40 cSt)

Lubricant

Example of pump code

Example of pump code
Example of pump code

O
(> 40 cSt)

40 litres

40
10 litres

10

Tank
capacity
100 litres

100
10 kg

10
Tank
30 litres

30

capacity
Tank

A
capacity
0,75 Kw
da 240

C20F
C20S

C20P

28
70 litres
70
a 280

Power

B
0,37 Kw
da 300

G
G
G

35
a 350
4

1
160 cm3 ø 7 mm 4 poles
da 260

37
a 330

10
40
10
Poles

4
400 cm3 ø 10 mm

SERIES C20F
Flow rate
SERIES C20S

SERIES C20P
da 340
6

6 poles

38
a 385

/
6

A
da 370 without

42
Tank external ø (mm)
a 420 control equipment 2 pumping
2

elements
selection guide

da 550
/

5
1
with

Control

60
a 600 control equipment

equipment
4 pumping
elements
4

elements

5
with
No. Pumping

R 50:1

1
2

L
minimum
Customized pumps

level

6
R 65:1 without
3
follow this model to customize your own pump.

Ratio
R 35:1

O
minimum

0
7

Level
level

7
control
R 75:1
Ratio

with minimum and

Y
7

without maximum level R 70:1

L
L

minimum

0
level without base
ultrasonic
/

for pump and without

with
O

connecting hoses minimum

1

1
minimum

1
with base for level
level
1

ultrasonic pump and

connecting hoses with

Level
control
L

minimum

1
with minimum and without
Level

level
/
control

maximum level motor operated

2
ultrasonic + visual reversing valve
2

maximum level + with with

Y

minimum and
Should the specific requirements be different from the ones of standard pumps,

filling filter motor operated

reversing valve maximum level

39
Accessories  Accessories 
 ADVANCED FLUID
MANAGEMENT SOLUTIONS

h a s a w id e range of
RAAS M
e n ts a n s o lu tions.
uipm
lubrication eq e m in o ur specific
a t th
Have a look
catalogues.

www.raasm.com
 RAASM products
are present worldwide through a network of
qualified dealers.
GENERAL SALES
CONDITIONS
FOR FOREIGN MARKETS

The following general sales conditions regulate the sale of goods and services by the company RAASM S.p.A. for customers residing outside the territory of the Italian State.
Art. 1 GOODS DELIVERY TERMS
The goods are delivered ex works RAASM S.p.A. The subsequent transport/shipment must occur by, in the name and at the expense of the purchasing customer, even by means of a carrier
appointed and designated by the same. All risks arising from loading, subsequent custody and transport are borne entirely by the purchasing customer.
Art. 2 MINIMUM ORDERS
Each order cannot be for less than € 1,500.00, net of fees, taxes, customs duties, discounts and rebates and any other charges not included in the price of the goods. If, at the option of RAASM
S.p.A., orders for lower amounts are accepted, an extra charge of € 155,00 shall be applied for order management administrative expenses.
Art. 3 ACCESSORIES
All the accessories given in the price list (plugs, oil bar taps, oil guns, grease guns, probes, protection caps, clutches, swivelling supports, etc.) are supplied exclusively for fitting to or combining
with the items RAASM S.p.A. produces
Art. 4 COMPLAINTS
Any defects immediately noticed after a brief inspection of the goods (damage, shortages or different product from that ordered) must be notified in writing to our company within 8 (eight) days
of receipt the goods. Any defects in the product noticeable only during its use must be notified in writing to RAASM S.p.A. within 8 (eight) days of being detected.
Any returns of goods must be authorized in advance by RAASM S.p.A. and freight charges are at the customer’s expenses.
Art. 5 DELIVERY TIMES/TERMS
Delivery times and dates are only approximate and are subject to change. Any delays in delivery do not entitle the customer to cancel the order or claim compensation for damages caused by
delay of delivery. Delivery times for urgent orders must be agreed directly with RAASM S.p.A. RAASM S.p.A. has the right not to carry out the order and/or totally or partially carry it out, without
this giving rise to reimbursement or claims for compensation for damage.
Art. 6 PACKS AND PACKAGING
Packaging costs are included in the price, except for special packing, which shall be charged at cost.
Art. 7 PRICES
The current Price list cancels and replaces the previous price list. In the event of changes to our price list and/or individual items, the goods shall be forwarded at the price in force on the
day of the order confirmation. The price list and/or the prices of individual items can be changed even without notice, according to the changes in market conditions or technical innovations/
modifications made to the product. The prices are understood to be ex works RAASM S.p.A.
Art. 8 PAYMENTS
Payments must be made exclusively to RAASM S.p.A. at the agreed conditions. Under no circumstances will deductions or roundings be accepted. In case of late payment with respect to
the agreed conditions, RAASM S.p.A. reserves the right to charge interest at the current rate, effective from the day after that agreed for payment, plus any additional expenses. Discounts
conditional on the payment term and already credited shall be recharged.
Art. 9 WARRANTY
RAASM S.p.A. provides each product with the communication of particular instructions for the installation, use and maintenance requirements and the need to carry out possible checks on
the product. All the technical information and data mentioned in the catalogue and in the price-list in force are not binding and can be changed without prior notice for the purpose of improving
the quality of the products. All products manufactured by RAASM S.p.A. are guaranteed for a period of 5 (five) years from the date of delivery to the first user. The user must keep and show
the sales invoice - or an equivalent document - together with the item’s serial number in order to make a claim under the RAASM S.p.A. guarantee. The 5 (five) year guarantee does not apply
to components which are subject to normal wear and tear (such as gaskets, diaphragms, O-rings, hoses, etc.), electronic components and items that are sold but not manufactured by RAASM
S.p.A. (marked with a red asterisk in the current product catalogue) which are guaranteed for 1 (one) year from the date of delivery to the first user.
1 (one) year warranty is valid also for the following products:
- digital litre counters and FCS system;
- cable reels;
- electric, pneumatic or hydraulic motor supplied with our industrial hose reels S. 600 and 700.
Incorrect installation, use or maintenance of the product shall void the warranty. Upon written notice, the articles must be returned free to our Factory for checking and acceptance. In any case,
the guarantee expires in the 10th year from the date of manufacture (indicated by the serial number), if the stated expiry takes place before the expiration terms indicated above (1 or 5 years
from delivery to the first user).

The manufacturer declines any responsibility for possible inaccuracies contained in this catalogue, due to printing or transcription errors. The manufacturer reserves
the right to make any changes or improvements of a functional, technical or aesthetic nature without prior notice.

The publication and the reprint of this price list is forbidden.

Art. 10 RESPONSIBILITY
RAASM S.p.A. is exempt from any responsibility and liability for accidents that may occur to persons and property, as a result of or during the use of the equipment, due to or depending on
the same whenever the products have been damaged during transport, tampered with or modified, or improperly used, or stored, installed, protected and preserved without complying with the
instructions of RAASM S.p.A. as given in the installation, use and maintenance instruction manuals for each product. RAASM S.p.A. is liable for the value for the supplied product and cannot be
held responsible in any way for other possible costs or additional costs that the customer may bear.

Art. 11 CONFIDENTIALITY
Information not in the public domain that is exchanged in the execution of the contract is subject to the obligation of confidentiality, secrecy and security; said information is covered as an
industrial secret and is of a confidential and reserved nature and may not be disseminated to third parties; its use is permitted exclusively and strictly to execute the supply contract.

Art. 12 INTELLECTUAL PROPERTY RIGHTS

The RAASM trademark, and likewise the name RAASM, RAASM S.p.A., the logo and the other distinctive signs are internationally registered trademarks, and RAASM S.p.A. does not authorise
their use and application under any circumstances. Without prior written consent from RAASM S.p.A., the content of catalogues, price lists, instruction manuals and similar, including content on
the website may not be reproduced, either entirely or partially, nor may it be transferred by electronic or traditional means, nor may it be modified or utilised by any means and for any purpose.
All rights are held by RAASM S.p.A. The customer acknowledges that RAASM S.p.A. holds exclusive ownership of all the parts, images, photographs and signs not in common usage, the content
in the catalogues, price lists, instruction manuals and similar and/or present on the website www.raasm.com and/or other channels and/or social networks used by RAASM S.p.A. for their
informational and marketing campaigns pursuant to Copyright Law and the Industrial Property Code.

Art. 13 INFORMATION ON THE PROCESSING OF DATA PURSUANT TO ITALIAN LEGISLATIVE DECREE 196/2003
In accordance with article 13 of Italian Legislative Decree 196/2003 - Personal Data Protection Code - you are hereby advised that the processing of the personal data, provided with the
purchase of goods or services and/or the supply of goods or services is solely for the purposes of carrying out the contract-based obligations and to comply with the specific requests from
customers/ suppliers, as well as adhering to legislative obligations, in particular accounting and tax obligations or to respect orders issued by public authorities or to exercise a right in court.
The data shall also be used for commercial statistics for corporate use and to obtain commercial information on our products and services if expressly authorised by the applicant.
The processing of data shall be done using hard-copy and computerised procedures, in the manner and within the limits necessary to achieve the aforementioned purposes.
Data may be communicated and processed by other companies in the Group for the same specified purposes, and may be made known to employees of our company, consultants and other
suppliers, always and exclusively within the limits of the aforementioned purposes. The provision of data is mandatory for the correct execution of the contract and pre-contract based obligations,
and failure to do so could result in it being impossible to fully comply with contractual obligations, and make it impossible to provide updates on the new products and services offered by our
company. Data shall be processed for the duration of the contract relationship in place and subsequently to fulfil any legal formalities.

Art. 14 RIGHTS OF DATA SUBJECTS

The information is aimed at defining the limits and methods for the processing of data, based on which individual customers and/or suppliers may freely authorise the collection and subsequent
use of data. Data subjects are entitled to the rights pursuant to article 7 of the aforementioned Code and in particular, the right to access their personal data, ask for the amendment, update
and cancellation thereof, if incomplete, incorrect or collected in violation of the law, and may object to the processing for legitimate reasons, addressing requests in this regard to RAASM S.p.A.
Pursuant to the same article the data subject also has the right to request the complete and updated list of the Data Supervisors, and to ask for the cancellation, transformation into anonymous
form or blocking of data processed in violation of the law, and to oppose in any case, for legitimate reasons, the processing thereof.
To exercise these rights, and in the case of problems or any requests for clarification regarding what has been explained herein, kindly address these to RAASM S.p.A. - Via Marangoni, 33,
Cassola (VI) - Italy or to the following email address: info@raasm.com.

Art. 15 DATA CONTROLLER

The Data Controller is RAASM S.p.A. with registered office at Via Marangoni 33, Cassola (VI) – Italy, and this is where the data processing shall take place.

Art. 16 COMPETENT LAW COURT

Any disputes shall be settled by the Law Court of Vicenza, Italy.

The company RAASM S.p.A. holds the exclusive Intellectual Property rights on
the RAASM trademark and all rights to its use and reproduction are reserved.
The RAASM trademark is a registered trademark and is protected at an
international level. No part of the RAASM trademark and its logo may be
utilized, copied and/or used in any form, time and space, even by means of
improper alterations.

The Intellectual Property rights on the images published in this catalogue are
owned exclusively by RAASM S.p.A. and any unauthorized reproduction is
prohibited.

Any use in general of the assets protected by the Intellectual Property rights of
RAASM S.p.A. is prohibited and is subject to the prior written permission of
RAASM S.p.A. 43
Ideal for
■ Machine tools
■ Woodworking machinery
■ Bottling machinery
■ Construction machinery,
concrete mixers, plaster pumps
■ Foundry and die casting
machines
■ Port facilities
■ Rubber industry machinery
■ Railways, rolling stock
■ Mines
■ Iron and steel industry
■ Machines for iron and
steel industry
■ Agricultural machinery

Authorized dealer
Company with quality and
environment system according
All rights revered by RAASM S.p.A.

to ISO 9001:2015 and ISO

14001:2015 standards

RAASM S.p.A. - 36022 S. ZENO DI CASSOLA (VI)

Via Marangoni, 33 - ITALY
Export department Tel. +39 0424 571130 - Fax +39 0424 571135
Technical department Tel. +39 0424 571150 - Fax +39 0424 571155
info@raasm.com - www.raasm.com

GB WRCC20-2015-GB