Pressure Switch and Pressure Sensor Catalog
Pressure Switch and Pressure Sensor Catalog
Pressure Switch and Pressure Sensor Catalog
,Ltd
Office: No. 220, Weishiwu Road, Economic Development Zone,
Yueqing Zhejiang, CHINA P.C.: 325600
Tel: +86-577-27822222
Fax: +86-577-27825222
Http: //www.lefoo.com
E-mail: info@lefoo.com Ver: 2018.09
ABOUT LEFOO
02 LF08A
High current pressure switch 0.2~45bar
03 LF08E
Pressure switch for water purifier
04 LF08V
Small vacuum pressure switch -0.5~-0.8bar
05 LF10
Air compressor pressure switch 25~190psi
06 LF10-L
Air compressor pressure switch 30~175psi
07 LF12
Air Pressure Switches
08 LF17
Air compressor pressure switch 15~500psi
09 LF18
Air compressor and pump pressure switch 1.0~16.0bar
10 LF19
Air compressor and pump pressure switch 2.5~12.5bar
11 LF10-W
Pump pressure switch 15~150psi
12 LF16
Pump pressure switch 20~100psi
13 LF17-W
Pump pressure switch 14~250psi
14 LFPC-1
Automatic water pump controller
15 LF20
Extended duty pressure switch 0.5~150psi
16 LF20-H
Ultra duty pressure switch 10~400psi
17 LF20-V
Vacuum pressure switch 1.1~22 in/Hg
18 LF25
Steam pressure switch 0.2~9.0bar
Pressure Switches
19 LF26
Steam pressure switch 0.2~10.0bar
20 LF05
Miniature steam pressure switch 0.2~5bar
21 LF30
Air differential pressure switch 0.4~8.0mbar
22 LF31
Air differential pressure switch 0.15~34 in W.C.
23 LF32
Air differential pressure switch 20~5000Pa
24 LF35
Air differential pressure switch 0.3~30mbar
25 LF37
Liquid level pressure switch 2~60 in W.C.
26 LF40-01
Air actuated pressure switch 0.25~15psi
27 LF42
Water dispensers high and low pressure switch H:1.5~2.5bar;L:0.1~0.2bar
28 LF55
Pressure switch for refrigeration system -0.5~42bar
29 LF58
Pressure switch for refrigeration system -0.2~32bar
30 LF5D
Oil differential pressure switch for refrigeration system 0.5~6.0bar
33 FS211
Electronic flow switch
34 FS213
Electronic flow switch
35 FSW1
Float switch
36 TS
Temperature controller
37 TSD
Differential temperature controller
Pressure Switches
38 TSH
Dual temperature controller
39 LFS-01
Miniature pressure & vacuum switch -800~-10mbar,10~600mbar
40 LFS-02
Miniature pressure & vacuum switch -800~-5mbar,5~800mbar
41 LFS-03
Miniature pressure & vacuum switch -800~-15mbar,15~2500mbar
42 LFDS10 Series
Intelligent digital pressure switch -100~1000kPa
43 LFDS63 Series
Intelligent digital display pressure switch V:-101~10kPa,0~20bar
44 LFDS704
Electronic pressure switch -1~0bar
45 LF701A
High pressure switch (diaphragm) 1~50 bar, M3 screw terminal
46 LF701B
High pressure switch (diaphragm) 1~50 bar, 6.4 mm plug type connection
47 LF702A
High pressure switch (piston) 50~200 bar, M3 screw terminal
48 LF702B
High pressure switch (piston) 50~200 bar, 6.4 mm plug type connection
49 LF703
High pressure switch (diaphragm) 1~50 bar, DIN 43650-A connection
50 LF704
High pressure switch (piston) 50~200 bar, DIN 43650-A connection
51 LF705
High pressure switch (diaphragm) 1~20 bar, 6.4 mm plug type connection
52 LF705A
High pressure switch (diaphragm) 1~20 bar, M3 screw terminal
53 LF706
High pressure switch (diaphragm) 1~20 bar, DIN 43650-A connection
54 LF707
High pressure switch (diaphragm) 1~50 bar, 6.4 mm plug type connection
55 LF708
High pressure switch (diaphragm) 1~20 bar, 6.4 mm plug type connection
Differential Pressure Transmitters
56 LFM108
Differential pressure transmitter 0~10000Pa
57 LFM11 Series
Digital display differential pressure transmitter -10000~10000Pa
58 LFM3 Series
Differential pressure gauge -10000~10000Pa
Pressure Transmitters
59 T2000
Universal pressure transmitter, -1~0······600bar
60 T3000
Liquid level pressure transmitter, 0~1······500mH 2 O
61 T3800
Digital pressure transmitter, 0~2······200mH 2 0
62 T1500
Differential pressure transmitter, 0~1±5kPa······5000kPa
63 T1050
High accuracy pressure transmitter, 0~2······60bar
64 T1030
High accuracy pressure transmitter, -1······-0.1bar~0~0.1bar·····1000bar
65 T1700
Absolute pressure transmitter, 0.1······400bar
66 T1800
High temperature resistant pressure transmitter, 0~1······2000bar
67 YG2221E
Engine oil pressure sensor, 0~6bar
Solenoid Valve
68 SVD20
Inlet Solenoid Valve
69 LFSV20-B
Drainage Solenoid Valve
Small multi-purpose
pressure switch 14
6.35*0.8
10.3
20.6
φ23
16.5
Hex.14
7/16-20UNF-2B
The LF08 switches are fixed set point, factory
calibrated pressure switches. It is automatic reset,
and can be Normally open or normally close
contacts. All metallic wetted components make Dimension in:mm
the LF08 switch compatible with a multitude of
chemicals in liquid or gas form. It is offered
numerous types of electrical terminations from
different size and style push on terminals to wire
leads with an array of standard industr y
connectors. In house machining capabilities
allows Lefoo to offer a wide variety of pressure LF08 Order Ref NO
fitting from different thread types and sizes to
units with internal deflator and cupper tubbing LF08 - 1 1 1 1 - 145-175psi
for sawing operations. BCD Pressure setting:Reset pressure 145psi Action pressure 175psi
01
Number Circuitry Base Material Connection Electrical connections
1 A SPST-NC B brass C 1/8NPT D 6.35×0.8
2 SPST-NO plated steel 1/4NPT 4.8×0.8
3 SPDT / R1/8 18AWG Wire leads
4 / / R1/4 /
5 / / G1/8 /
6 / / G1/4 /
7 / / 1/4 Copper tube /
8 / / 7/16UNF Male /
9 / / 7/16UNF Female /
10 / / 7/16UNF Female with deflector /
Specification
Model LF08
Media Air,Water,motor lils,transmission oils,Hydrocarbon Media,Refrigeration fluid
Pressure Range Tolerance Proof Pressure
0.2~6bar(low pressure) ±0.5bar 15bar
Pressure Range/ 6~10bar ±0.7bar 35bar
Tolerance/
Proof Pressure 11~20bar ±1bar
21~30bar ±1.5bar 45bar
31~45bar ±1.5bar
Burst Pressure 5000psi
Environment temperature:low pressure:-30~65℃ ,High pressure:-35~120℃;
Operating Temperature Range
Medium temperature:-50~120℃
Switch Type SPST(NC OR NO); SPDT
Electric Rating 120Vac 6FLA ,40.2LRA ; 240Vac 4FLA ,26LRA 120/240Vac 375VA ;36Vdc 3A
Endurance 100000
72.9
φ34.3
The LF08A switches are fixed set point, factory
calibrated pressure switches. It is automatic reset,
S14 and can be normally open or normally close
8
Specification
Model LF08
Media Air,Water,motor lils,transmission oils,Hydrocarbon Media,Refrigeration fluid
Pressure Range Tolerance Proof Pressure
0.2~6bar(low pressure) ±0.5bar 15bar
Pressure Range/ 6~10bar ±0.7bar 35bar
Tolerance/
Pressure value 11~20bar ±1bar
21~30bar ±1.5bar 45bar
31~45bar ±1.5bar
Burst Pressure 5000psi
Environment temperature: low pressure-30~65℃ ,High pressure:-35~120℃;
Operating Temperature Range
Medium temperature: -50~120℃
Switch Type SPST(NC OR NO); SPDT
120VAC,13FLA ,65LRA ; 240VAC,10FLA ,45LRA ; 480VAC,4FLA ,24LRA
Electric Rating
120/240VAC,480/720VA ; 28VDC,15AMP; 24VAC,125VA
Endurance 100000
Connection Please see the selection table (customizable)
Electrical connections 6.35*0.8; Wire connection (can be customized length and electrical plug)
Conversion: 1bar=14.5psi 1MPa=10bar
www.lefoo.com
LF08E
Pressure switch for
water purifier
Terminal
φ27.5
58.5
Housing
25.2
9 1/4"Connector
NC
SPSTContacts
03
Dimension in: mm
This product is specially designed for water
purifier, which can replace traditional high-low
pressure switch. It is more sensitive action and
used for wider range of applications.
Specification
Item LF08E
Pressure range 0.05~0.35MPa
Performance One pressure setting/ Two pressure setting
www.lefoo.com
LF08V
Small vacuum
pressure switch
φ22.6
48
S14
8
11
NPT1/8
Dimension in:mm
04
Specification
Model LF08V
Media Air,Water,motor lils,transmission oils,Hydrocarbon Media,Refrigeration fluid
Pressure Range Reset pressure Tolerance
Pressure Range/
Tolerance -0.5~-0.8bar -0.25~-0.6bar ±0.05bar
Differential pressure≥0.25 bar
Burst Pressure 10bar
Operating Temperature Range -20~65℃
Switch Type SPST(NC OR NO)
120Vac 6FLA ,40.2LRA ; 240Vac 4FLA ,26LRA
Electric Rating
120/240Vac 375VA ;36Vdc 3A
Endurance 300000
Conversion: 1bar=14.5psi 1MPa=10bar
www.lefoo.com
Air compressor
pressure switch
94
77.6
90
17
81
51.5
80
116.5
23
51.5
17
80
111.5
23
51.5
06
Specification
Operating Factory Electrical Contact
Model Media Pressure Range Setting Differential Rating Arrangement Connection
G1/4,G3/8 or
LF10-L1H Air 45-175psi 85-115psi 30-45psi 120VAC、20A NC 1/4,3/8NPT
Female
G1/4,G3/8 or1/4,
LF10-L4H Air 45-175psi 85-115psi 30-45psi 120VAC、20A NC 3/8NPTFemale
(Four ports)
103
92
Cable
50
connection
Unloadingvalve 30
58.5
110
71
82
Dimension in: mm
07
Specification
Operating Factory Contact
Model Electrical Rating
Pressure Range Differential Setting Arrangement Connection
www.lefoo.com
Air compressor
pressure switch
96
105
90
08
Dimension in:mm
Specification
Operating Factory Electrical Contact
Model Media Pressure Range Setting Differential Rating Arrangement Connection
134
47.2
32.2
59.2
63.5
09
Specification
Operating Factory Electrical Contact
Model Media Pressure Range Setting Differential Rating Arrangement Connection
71.5
118.5
32.2
64.8
10
Dimension in:mm
Specification
Unloader Operating Factory Electrical Contact
Model Media Pressure Range Differential Setting Rating
Valve Arrangement
1-6bar 1-3bar 2-4bar
250VAC
LF19 Air With 2-11bar 1.4-3.5bar 6-8bar NC
16A/25A
5-14bar 1.8-4.0bar 8-10bar
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
Pump pressure switch
84
76
65
Dimension in:mm
11
LF10-W series pressure switches provide time
tested, reliable control for automatic water LF10-WS and LF10-WR Order Ref NO
systems. The switch is universally acceptable LF10(A) - W(S or R) - 1 1 1 - 30 - 50psi
for use as original equipment on water well
Contact Type: NC NO B C Pressure setting:Cut in 35psi Cut off 50psi
pumps or pumping systems.
Specification
Operating Factory Electrical Contact
Model Media Pressure Range Setting Differential Rating Arrangement Connection
Water 15-82psi 20-35psi 15-30psi 120VAC、20A
LF10-WS (120VAC、26A) 1/4NPT
Water 30-100psi 30-50psi 20-35psi NC Male or
(LF10A-WS) 240VAC、12A Female
Water 35-150psi 85-115psi 30-40psi (240VAC、26A)
97
70
Dimension in:mm
12
Specification
Min On Min Off Factory Electrical Rating Contact
Differential
Model (Cut-In) (Cut-Out) Setting 1Phase 3Phase Arrange- Connection
psi
psi psi psi ment
15-30 20-40
20 80 15-30 30-50
LF16 2HP 3HP 5HP
15-35 40-60
1/4 Male
40 100 20-35 70-100
NC or Female
15-30 20-40 NPT
20 80 15-30 30-50 1.5HP 2HP 3HP
LF16-1 15-35 40-60
40 100 20-35 70-100 2HP 3HP 5HP
96
105
80
13
Dimension in:mm
The rugged LF17 pressure switch is designed for LF17-W Order Ref NO
the demanding requirements of lager, heavy duty LF17 - W - 1 1 1 - 80 - 100psi
commercial water pump system. BC Pressure setting:Cut in 80psi Cut off 100psi
Specification
Operating Factory Electrical Contact
Model Media Pressure Range Setting Differential Rating Arrangement Connection
165
171
230
14
Specification
Model LFPC-1
Rated voltage 220-240VAC
Maximum working pressure 10bar
Frequency 50-60Hz
Connection R1”
Maximum current 8A
Protection level IP65
Maximum power 1.5kW(2HP)
Maximum operating temperature 65℃
Factory setting 1.5bar, stop when water pressure reach 3.5bar
www.lefoo.com
Extended duty pressure switch
ProtectionPlug
6.3Faston
NO
63
C
NC
SPDTContacts
11.5
10
FixedPart
D
φ37.5
Regulationhallenscrew5mm
The LF20 pressure switch is specifically designed
to stand up to extended duty applications. This
switch is factor y set but capable of field Dimension in:mm
adjustment. It features different diaphragms for
compatibility with a wide variety of fluids, and
various terminations including a Metri-Pack
connector that forms a tight seal when connected.
It can be widely used for pool and spa, anti-skid LF20 Order Ref NO
braking systems, water pump systems, and dental
air compressors, heavy construction, off road LF20 - 4 1 1 1 1 1 - 10psi
equipments and other pressure control systems. BCDEF Pressure setting: 10psi
15
Pressure Set
Number Point Range Circuitry Base Material Connection Terminals Cover
0 / / / / / none
1 0.5-1psi±0.3psi B SPST-NC C brass D 1/8NPT E 1/4 blade F cover A
2 1.1-3psi±0.5psi SPST-NO plated steel 1/4NPT #8-32 scer ws cover B
3 3.1-7psi±1psi SPDT-NO-C-NC stainless steel R1/8 wire leads /
4 8-13psi±2psi SPST-NO(adjustable) / R1/4 / /
5 14-4psi±3psi SPDT-NO-C-NC(adjustalble) / G1/8 / /
6 25-50psi±5psi / / G1/4 / /
7 51-90psi±7psi / / / / /
8 91-150psi±10psi / / / / /
Specification
Model LF20
Media Air, water, motor oils, transmission oils, jet fuels and other similar Hydrocarbon Media
Pressure Set Point Factor y set from 0.5 to 150psi
Max Operating Pressure 150psi for 0.5-24psi set point range, 250psi for 25-150psi set point range
Proof Pressure 500psi
Burst Pressure 750psi for 0.5-24psi set point range, 1250psi for 25-150psi set point range
Opeating Temperature Range -40℃ to +120℃
Switch Type Direct action,blade contact
Resistive: 15AMP-6VDC、8AMP-12VDC、4AMP-24VDC
Electric Rating
Inductive: 1AMP-120VAC、0.5AMP-240VAC
Contact Arrangement SPST-N.O,N.C 1circuit adjustable dual circuit,or 2circuits adjustble dual circuit.Also available are N.O/N.O.dual circuit and N.C/N.C.dual circuit
Terminal #8-32 screws,1/4" blade
Plated Steel,plastic or stainless steel base;various base connector threadsizse;
Options
wire leads(potted & sealed);Teflone or EPDM diaphragm
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
ProtectionPlug Ultra duty pressure switch
6.3Faston
NO
63
C
NC
SPDTContacts
11.5
10
FixedPart
D
φ37.5
Pressure Set
Number Circuitry Base Material Connection Terminals Cover
Point Range
0 / / / / / none
1 10-35psi±3psi B SPST-NC / D 1/8NPT E 1/4 blade F cover A
2 35-75psi±7psi SPST-NO C plated steel 1/4NPT #8-32 screws cover B
3 75-150psi±10psi SPDT-NO-C-NC stainless steel R1/8 wire leads /
4 150-250psi±20psi SPST-NO(adjustable) / R1/4 / /
5 250-400psi±50psi SPDT-NO-C-NC(NO.adjustalble) / G1/8 / /
6 / / / G1/4 / /
The polyimide diaphragm is not suit for water, if customer is to use the pressure switch in water, please contact the factory.
Specification
Model LF20-H
Media Air,water,motor oils,transmission oils,jet fuels and other similar Hydrocarbon Media
Pressure Set Point Factor y set from 10 to 400psi
Max Operating Pressure 500 psi
Proof Pressure 2000 psi
Burst Pressure 4000 psi
Opeating Temperature Range -40℃ to +120℃
Switch Type Direct action,blade contact
Resistive: 15AMP-6VDC、8AMP-12VDC、4AMP-24VDC
Electric Rating
Inductive: 1AMP-120VAC、0.5AMP-240VAC
Contact Arrangement SPST-NO,NC,SPDT
Terminal #8-32 screws,1/4" blade, Metri-Pack
Connection 1/8"NPT Male,1/4"NPT Male,G1/8"Male,G1/4"Male
Options Base connector sizes,wire leads,NO/NO.dual circuit and NC/NC.dual circuit
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
Vacuum pressure switch
ProtectionPlug
6.3Faston
NC
63
C
NO
SPDTContacts
11.5
10
FixedPart
D Adjustmentscrew
φ37.5
Pressure Set
Number Circuitry Base Material Connection Terminals Cover
Point Range
0 / / / / / none
1 1.1-3"Hg(15-41"H20)±0.5"Hg B SPST-NC C barss D 1/8NPT E 1/4 blade F cover A
2 4-8"Hg±1"Hg SPST-NO plated steel 1/4NPT #8-32screws cover B
3 9-17"Hg±2"Hg / stainless steel R1/8 wire leads /
4 18-22"Hg±3"Hg / / R1/4 / /
5 / / / G1/8 / /
6 / / / G1/4 / /
Specification
Model LF20-V
Media Air
Pressure Set Point Factor y set from 1.1 to 22 in/Hg vacuum
Max Operating Pressure 30 in/Hg vacuum
Burst Pressure 150 psi
Opeating Temperature Range -40℃ to +120℃
Switch Type Direct action, blade contact
Resistive: 15AMP-6VDC、8AMP-12VDC、4AMP-24VDC
Electric Rating
Inductive: 1AMP-120VAC、0.5AMP-240VAC
Contact Arrangement SPST-NO, NC
Terminal #8-32 screws,1/4" blade, Metri-Pack
Connection 1/8"NPT Male,1/4"NPT Male,G1/8"Male,G1/4"Male
Material Contact: Silver alloy, gold plated ; Base: Plated Steel ;
Cover : Glaee reinforced polyester ; Diaphragm: Fluorosilicone elastomer
Options Various base connector sizes,wire leads(potted & sealed)
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi 1 in/Hg=0.49psi
www.lefoo.com
Steam pressure switch
Adjustmentscrew
NO
47.5
C
NC 6.3Faston
9
8
SPDTContacts
D
FixedPart
φ38
45.6
Specification
Model LF25
Media Non hazardous gas, liquid or steam
Operating Pressure 0.2-0.6bar 0.5-1.0bar 1.0-2.5bar 2.0-4.0bar 3.0-7.0bar 5.0-9.0bar
Proof Pressure 3bar 3bar 10bar 10bar 10bar 10bar
Opeating Temperature Range +125℃ Max imum
Contact Arrangement SPST or SPDT
Electric Rating SPST or SPDT /Normal Close:16(4)-250VAC (other ratings are available if necessar y)
Terminal 6.3 or 4.8mm male Q.C. Insulation cover is available if necessar y
Connection 1/8NPT-27 or 1/4NPT-18 Male (other connection is optional)
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
Steam pressure switch
58.7
Hex.14
19
7.3
G1/8
φ35
Specification
Model LF26
Media Non hazardous gas, liquid, oil or steam
Operating Pressure 0.2-6bar 0.2-10bar
Proof Pressure 12bar
Differential Fixed 0.1-0.4bar ; Adjustable 0.2-0.8bar
Opeating Temperature Range +125℃ Max imum
Contact Arrangement SPST or SPDT
Normally closed: NC 15A resistance load,1.5 inductive load/250V
Electric Rating
Normally open: NO 9A resistance load, 0.9 inductive load/250V
Terminal 6.3 mm Male Q.C Insulation cover is available if necessar y
Connection G1/8 or G1/4 Male (other connection is optional)
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
Miniature steam
pressure switch
6.35*0.8
37 6.35*0.8
3.5
31
4
8
S14 G1/8 G1/8
φ22
17
Dimension in:mm
Specification
Model LF05 LF05A
Media Air, water, water vapor Air, water, water vapor
Pressure Setting Range 1.5~4.0 bar 1.0~5.0 bar
Max Working Pressure 4.5 bar 5 bar
Proof Pressure 8 bar 10 bar
Working Temperature Max 125℃ Max 125℃
Contact Arrangement SPST-NC SPST-NC
Electrical Rating 16A/250VAC,30,000 cycles 16A/250VAC,50,000 cycles
Terminal 6.35×0.8mm 6.35×0.8mm
Connection G1/8"male G1/8"male
Connection: Brass Connection: Brass
Material Diaphragm: Stainless steel Diaphragm: Stainless steel
Contact: Fine Silver Contact: Fine Silver
88
φ77.9
25.6
48.4
The LF30 employs a differential pressure to
actuate a precision snap switch at chosen
pressure setting. This may be the difference
Dimension in:mm
between atmospheric and a negative or positive
pressure or between any two given pressures. 21
When a change of pressure occurs between the LF30 Order Ref NO
negative pressure chamber and the positive
LF30 - 4 1 1 1 - P70Pa - 100Pa
pressure chamber the main diaphragm activates
B C D Pressure setting in pa:P=Positive V=Vacuum
the snap switch at a pre-determined value. ON:100Pa OFF:70Pa
Specification
Model LF30
Media Air,products of combustion or natural gas
4 screws with maximum penetration depth of 6.3mm into appropriate
Mounting/Fixing
mounting holes,or fixed with optional bracket
The LFAS is position sensitive.It may be mounted in most
Mounting Position
positions provided it has been calibrated
R
ON
M
CO
NC
4.8×0.8
6.35×0.8
V
77
φ3 .6
101.6
φ85.1
57.4
P2 -
The LF32 is an adjustable differential pressure
switch capable of detecting miniscule changes
P1 +
in pressure due to the size and proven design.
The switch set point or switching point can be φ6
f i e l d a d j u s t a b l e w i t h o u t t h e n e e d of a
manometer by simply using the adjustment
knob and the built in calibrated visual scale. Dimension in:mm 23
This switch is equipped a clear cover that not
only protects the adjustment knob to be move
involuntar y but also provides class IP54
protection
Specification
Model LF32
Media Air, non-combustible and ono-aggressive gass
Max Operating Pressure 10kPa
Mounting Position Diaphragm in any vertical Plane
Degree of protection IP54(with cover), IP00(without cover)
Operating Temperature -40℃ to +85℃
Contact Arrangement SPDT
Resistance: initial<100 milliohms
Electrical Rating
Current: 1.5A(0.4A)/250V
Termimnal 6.3mm×0.8 blade or screw terminal
Connection Φ6.4mm for tube connection
Conversion: 1in W.C.=249Pa 1mbar=100Pa
www.lefoo.com
Air differential
pressure switch
152.4
122.7
φ3
80.9
24
Dimension in:mm
The LF35 are general purpose airflow proving
switches designed for HVAC, detection of
blocked filters and fan suction, air flow
LF35 Order Ref NO monitoring in ducts, pipes, tunnels, and other
LF35 - 1 1 A 1 - P0.5mbar energy management applications. It may be used
BCD Pressure setting:P0.5mbar P=Positive;V=Vacuum to sense positive, negative or differential air
pressure.
Specification
Model LF35-1 LF35-2
Media Air
Mounting Position Diaphragm in any vertical Plane
Field Adjustable Range 0.5±0.05mbar to 30.0mbar 0.2±0.05mbar to 5.0mbar
Progressive,increasing from approximately Progressive,increasing from approximately
Switch Differential 0.05mabr at minimum set point,to 0.05mabr at minimum set point,to
approximately 2.0mbar at maximum set point approximately 0.25mbar at maximum set point
Maximum Pressure 30mbar
Operating Temperature -40℃~+82℃
Electrical Rating 300VA pilot duty at 115-277VAC,10A ,non-inductive,277AVC
Ferrule and nut compression type connectors that accept 0.25"OD rgid or semi-rigid
Connection
tubing;male 0.25"slip-on connector
Contact Arrangement SPDT
76.5
78.5
25
LF37 diaphragm pressure switch is available for
Dimension in:mm
various sumps, effluent, and sewage application
to control the liquid level. Various switch settings
are available for to turn-on or turn-off the pump.
The diaphragm pressure sensing design make it
more reliable than traditional float ball LF37 Order Ref NO
mechanism. Port connection design make it can
LF37 - 1 1 1 - 4.5" - 6"H 2 O
sense the pressure without immersing the liquid
BC Pressure setting: cut in :6"H2O ; cut off : 4.5"H2O
directly.
Specification
Model LF37
Media Air,water or other non-hazardous liquid
Diaphragm Pressure switch operation:provide water level signals
Basic function
to appliance control,level value can be set on customer request
Pressure Range liquild level Range 2~60 in W.C.
Proof Pressure 5psi
Contact Type SPDT,SPST-NC/NO
12/13.8A ,125VAC
10A ,250VAC
Electrical Rating
1/2HP,125/250VAC
3/4HP,125/250VAC
Ambition Temperature 40℃
Terminal 6.3×0.8 blade
NO 6.3Faston
C
49.5
NC
SPDTContacts
14.2
D
FixedPart
44.9
Dimension in:mm
26 Button LF40 combination switch box LF40-01 is provided with a snap action switching
for higher current capacity, SPDT contact form
and switch deadbands. It can be used together
with air button for remote control purpose, which
LF40-01 Order Ref NO is widely used in food waste disposer, pumps for
LF40-01-1 M 1 3 1 -3psi swimming pools and spas, hot tubs, sanitary
B C D Set Point(psi):3psi equipment, medical equipment etc. Used as a
remote control, LF40-01 has two actions,
Action Type:M=Momentary action; A=Alternate action
Momentary action and Alternate action.
50.6
55.2
63.5
27
27
Dimension in:mm
LF42 series pressure switch is used in water
supply pressure protection of water inlet. This
series include two models LF42H(high pressure
protection) and LF42L(low pressure protection).
LF42H is the high pressure protection switch
model. If the pressure of the pressure vessel
transferred reaches the setting value while the
vessel is full filled with water, the switch will cut off
the circuit to make the pump stop. So the pump
will not be damaged. LF42L is the low pressure
protection switch. If the pressure of water inlet
lower than set value, RO will not work and keep
dewatering, then the switch will cut off the circuit
to make the pump stop. It can prevent the
booster pump still working without water which
may lead to the damage of the circuit. If the
pressure of the water inlet returns to the lowest
set volume, the pump will work again.
Specification
Model LF42H LF42L
Media water water
cut off pressure: 2.5bar±0.5bar cut off pressure: ≤0.1 bar
Pressure set range cut in pressure: ≥0.2 bar
cut in pressure: 1.5bar±0.5bar
Proof pressure 18bar 18bar
Durability >40000 cycles >40000 cycles
Working temperature 5~45℃ 5~45℃
Switch type Microswitch , normal close Microswitch , normal open
Electrical rating Voltage: 250V AC Current: 16A Voltage: 250V AC Current:16A
Terminal 4.8*0.8 blade 4.8*0.8 blade
Connector A quarter fast interface A quarter fast interface
Conversion: 1bar=14.5psi 1MPa=10bar
www.lefoo.com
83.5 44 Pressure switch for
refrigeration system
25
60
87
Dimension in:mm
Contact Function
LF55 Series pressure switches are used to control
Arrow means the direction of pressure increasing,M means hand reset the pressure of compressor in refrigerant system,
28 3 M 5 4 M 4 also available in air or water fluid. This series have
1 1 1 1
quite stable performance with internal micro-
switch structure. Standard mounting bracket are
5 3 2 2
provided
Electrical Function
Rated Amps.(A)\Rated Voltage(V) 125VAC 250VAC 24VDC
Full Load 20A 10A 8A
Locked Roter 72A 72A 64A
Temperature -10~120℃
Specification
Range(bar) Differential (bar) Factory Setting(bar) Max Operating
Model Pressure(bar)
Min Max Min Max OFF ON
LF5502 -0.5 2 0.2 0.7 1 0.5 16.5
LF5503 -0.5 3 0.35 1.5 2 1 16.5
LF5506 -0.5 6 0.6 4 3 2 16.5
LF5506M -0.5 6 Reset Differential≤1bar 3 Manual Reset 16.5
LF5508 -0.2 7.5 0.7 4 3 2 20
LF5510 1 10 1 3 6 5 16.5
LF5514 2 14 1 4 10 8 20
LF5516 3 16 1 4 10 8 35
LF5520 5 20 2 5 16 13 35
LF5530 8 30 Fixed 3 to 5bar 20 15~17 35
LF5530M 8 30 Reset Differential≤4bar 20 Manual Reset 35
LF5530D 5 30 3 10 20 15 35
LF5532 8 32 2 6 20 17 35
LF5542 8 42 4 10 30 25 46.5
Conversion: 1kgf/cm²=14.2psi 1psi=68.95mbar
Note : Default connection is M12x1.25, if need British connection such as 7/16-20UNF,
please add 'E' in the end of the model
Normally,use English system is screw thread is 7/16-20UNF
www.lefoo.com
Pressure switch for
refrigeration system
121.5
44
25
60
88.5
82
29
Dimension in:mm
Specification
Press Range(bar) Differential(bar) Factory Setting(bar) Max Operating
Model Pressure(bar)
Side Min Max Min Max OFF ON
Low Side -0.2 7.5 0.7 4 4 2 20
LF5832
High Side 8 32 Fixed 4 20 15 35
Low Side -0.2 7.5 0.7 4 4 2 20
LF5832HM
High Side 8 32 Fixed 4 20 Manual Reset 35
Low Side -0.2 7.5 Fixed 4 3 Manual Reset 20
LF5832HLM
High Side 8 32 Fixed 4 20 Manual Reset 35
www.lefoo.com
80.4 49.5 Oil differential
47 pressure switch
50
150
60.5
25
Dimension in:mm
30
LF5D series are pressure differential switches
which normally used in water or oil fluid to
control the pressure differential of the outlet tube
Contact Function and inlet tube. Bellowing is one of the typical
SPDT application: install the valve in the pipeline which
near the water(oil) pump, when the pressure
3 NO 1 Common contact differential of the two sides of the system
1 1-3 When pressure increase,it’s closed increasing or decreasing and exceed the setting
COM 1-5 When pressure decrease,it’s closed value, the valve will open. Then the system
pressure differential will reach to the normal
↑ Pressure rise’s way
5 NC circulate. Both two sides of LF5D series have a
Notes:1)When install the pressure switch's connection tube,don’t wrong side of high high sensitive components, the switch will act to
control the system of the equipment such as
pressure & low pressure.
motor driven valve while the pressure differential
2)When install the pressure switch’s connection tube,the screw with the changes.
connection must be use two10" spanner to do it colse.
Electrical Function
Rated Amps.(A)\Rated Voltage(V) 125VAC 250VAC 24VDC
Non-Inductive Current 20A 10A 10A
Full Load 15A 8A 8A
Locked Roter 72A 72A 64A
Temperature -20~110℃
Specification
Differential Adjust range(bar) Max Operating
Model Factory Setting(bar) Pressure(bar)
Min Max
LF5D2 0.5 2 0.5 16.5
LF5D4 0.5 3.5 1 16.5
LF5D6 0.5 3.5 1 33
LF5D6H 1 6 1 16.5
LF5D4H 1 6 1 33
Note : Default connection is M12x1.25, if need British connection such as 7/16-20UNF,
please add 'E' in the end of the model
Normally,use English system is screw thread is 7/16-20UNF
www.lefoo.com
FS5 Series
Liquid flow switch
Features
Max liquid pressure: 1 MPa, can be used in multiple applications.
There are 3 stainless steel paddles, can be used in 25 to 75mm diameter pipe.
Number of paddles is changeable and length of paddle is trim-able according to
customer requirements.
With additional 6''paddle, FS series liquid flow switch can be used in 100 to 150mm
diameter pipe.
Adjustable flow setting, Users can set the flow value according to their requirements.
For user convenience, FS52 flow switch has large room for wiring.
FS51/FS52 can also be provided with stainless steel connection, which is suitable for
ammonia and other medium.
Application
The typically application is used to protect the cooling system, when the cooling water
is off, FS flow switch can shut off the compressor current efficiently in order to protect
the freezer and entire system from being damaged.
FS51 FS52
FS series liquid flow switch is designed for Performance Parameter
managing the flow changes when the liquid flows
in the pipe, such as water, ethylene glycol or Electric load: AC250V 10A
other non-hazardous liquids. When the liquid Max working pressure: 10.34Bar
flow is higher or lower than the setting value, the Flow temperature: 0-120℃
single-pole double- throw contacts (SPDT) can Environment temperature: 0-60℃
get through one circuit and at meantime to break The endurance of bellows: 500000 cycles
the other circuit. FS series liquid flow switch is
Ingress protection: IP53
commonly used for chain reaction or “no flow”
protection.
Pipe Diameter (mm) 25 32 40 50 65 80 100 125 150 200 100* 125* 150* 200*
Flow
increase
(red blue 0.95 1.32 1.70 3.11 4.09 6.24 14.8 28.4 43.2 85.2 8.4 12.9 16.8 46.6
Min closed)
Adjus
tment Flow
decrease
(red yellow 0.57 0.84 1.14 2.16 2.84 4.32 11.4 22.9 35.9 72.7 6.13 9.31 12.26 38.6
closed)
Flow
increase
(red blue 2.0 3.02 4.36 6.6 7.84 12.0 29.1 55.6 85.2 172.6 13.4 26.8 32.7 94.26
Max closed)
Adjus
tment Flow
decrease
(red yellow 1.93 2.84 4.09 6.13 7.23 11.4 27.7 53.4 81.8 165.8 17.3 25.21 30.66 90.85
closed)
Installation
1. Pipe connection: FS series flow switch be provided with 1", 1/2", 3/4" NPT connections.
2. The arrow direction in the cover must be as same as the flow direction in the pipe.
3. The flow switch is suggested to be installed on horizontal pipes, if it have to be on vertical pipes, then the direction in the pipe must be upward
flow. It is not allowed to be installed on the vertical lines with downward flow.
4. To avoid the paddle damage, flow reversal is not allowed when the flow switch is working.
www.lefoo.com
The paddle trimming figure
* * *
1in 1.5in 2in 2.5in 3in 4in 5in 6in
Attention
the paddles with “ * ” symbol are installed in factor y
the paddle with “△ ” symbol is the additional paddle.(not installed)
the balance paddles are for trimming
when install the trimmed paddles, the end of paddle should keep 5--10mm distance from the pipe end and no friction with the pipe
T-connector
Flow direction
A A
Flow direction
www.lefoo.com
FS211
Electronic flow switch
86 86 50
44 28 44 28
φ8
75
G1/4
φ8
G1/2
15
15
27
27
14
Principle、Structure: G1/4 G1/2 开关量输出型
There are two resistors in the enclosed probe 1 brown
L+
PNP
based on the thermal principle. One of them is 2 white PNPOutput
(10)
0.39
( 10 ) 4 black
0 . 39
heated as the detection resistor and the other is M18×1.5 M18×1.5
3 blue
not heated. As the reference resistance, when L-
1.06 1.06
the medium flows, the heat on the heating
(29.5)
(27) (27)
1.16
(37)
1.46
resistor is taken away. The resistance value is 1 brown
L+
NPN
changed, the two resistance differences are 2 white NPNOutput
G1/2
(14)
0.55
M12×1 4 black
used as the basis for judging the flow rate.
(13.5)
0.53
3 blue
Features: L-
No moving parts, maintenance-free, easy to 1 brown
install, one type can meet a variety of diameter FG12 FM12 L+(L)
RELAY 4 black
NO Relayoutput
requirements. Switching value is continuously 5 gray
2 black
COM
adjustable, ver y low pressure loss, compact NC
structure, LED display flow trends and switch
Dimension (unit: mm) 3 blue
L-(N)
status.
Application:
Gas-liquid dual-use type, used for pneumatic
and hydraulic systems, circulating water, FS211 Order Ref No
cutting fluid and lubricating oil flow FS211-G2-H-D-P-R-Q 33
monitoring, and pump idling protection.
1 2 3 4 5 6
Pressure Connection
1 Connection 2 Type 3 Power Supply 4 Output 5 Output method 6 Connector Type
G2=G1/2 H=Male D=VDC24V±20%Power Supply P=PNP Output R=NO+NC Output Q=Socket Connector Type
G4=G1/4 N=NPN Output
C=Relay output
Socket Connector Order Ref No Note: The relay type products need to use 5-pin
ST04-PU-02-F-G connector, type and core connector, Just change
S (E) T04 to S (E) 05
1 2 3 4 5
1 Socket Connector 2 Material 3 Line length 4 Female plug 5 Shape
ST04=M12 PU=PUR 02=2M F=F G=Straight type
ET04=M12 05=5M W=Cur ved type
10=10M
Specification
1...150cm/s(Water),3...300cm/s(Oil),
Setting Range Initializtion time About 8s
20...2000cm/s(Gas)
Signal output PNP, NPN, Relay Type, NO+NC Electrical protection Reverse, short circuit, overload protection
Power Supply 24V±20%DC or 230V±15%DC Protection level IP67
Turn on current Max 400mA(PNP, NPN); Max 4A (Relay Type) Medium temperature -20~80℃
No-load current Max 80mA Ambient temperature -20~80℃
Flow indication LED (6pcs) Storage temperature -20~100℃
Medium temperature
≤4℃/s Weight About 0.4kg
change
Response time 1--13s,Typical value 2s
www.lefoo.com
FS213
Electronic flow switch
1 brown
PNP L+
φ53 2 white
4 black PNPOutput
3 blue L-
43
27
1 brown
NPN L+
2 white NPNOutput
4 black
15
3 blue
L-
G1 / 4
G1 / 2
27
1 brown
L+(L)
13
RELAY 4 black
NO Relayoutput
G1/4orG1/2 5 gray
φ8 COM
2 black
NC
3 blue
L-(N)
(10)
Principle、Structure:
0.39
(10)
0.39
M18×1.5 M18×1.5
There are two resistors in the enclosed probe
1.06 1.06
(27) based on the thermal principle. One of them is
(29.5)
(27)
1.16
(37)
1.46
G1/2
M12×1
(13.5)
Specification
1...150cm/s(Water),3...300cm/s(Oil),
Setting Range Initializtion time About 8s
20...2000cm/s(Gas)
Signal output PNP, NPN, Relay Type, NO+NC Electrical protection Reverse, short circuit, overload protection
Power Supply 24V±20%DC Protection level IP67
Max 400mA(PNP, NPN);
Turn on current Max 1A@24V ac/dc (Relay Type) Medium temperature -20~80℃
www.lefoo.com
FSW1
Float switch
φ69±1.0
90±1.5
108±1.5
35
Dimension in: mm
Specification
Item FSW1
Switch Type SPDT
Electric rating 13amp@120/240 VAC 1/2hp
Working temperature 0~90℃ Dr y, 0~60℃ Wet
Fixed way Heavy hammer 2.51bs
Weight 11bs(Not including heavy hammers)
Cable length Customized
Media Sewage
Operating range Wide-angle pumping range is about 5 inches to 18 inches
www.lefoo.com
TS
Temperature controller
80 49
temperature
2.4
dajustingscrew
20.5
62.8
25
L=1M
TS series temperature controller can be directly
connected to single phase motor under 1KW, or
installed in controller circuit of DC motor and
large AC motor. TS series temperature controller
can match with solenoid valve to control the
temperature of the refrigerator. TS series
temperature controller is equipped with a SPDT
double throw switch. The switching points
Dimension (unit: mm) depend on the setting value of temperature
controller and temperature thermometer bulb
sense.
Specification
Factory settings (℃) The highest Dimension of thermo-bulb (mm)
Adjusting range Working
Model temperature
(℃) Length conditions (℃)
36 ON OFF of thermo-bulb (℃) Diameter
TS15 -15~15 -5 0
TS40 0~40 17 20 70
Electrical Ranting
3
1
Rated Voltage (V)
A.C.110 A.C.220 5
Rated Current (A) M
8A 1 :Common contact
Induced Full load current 15A
current 1 3 :When temperature increases,
Instantaneous current 72A it’s closed
1 5 :When temperature decreases,
it’s closed
M :Manual resat
www.lefoo.com
TSD
Differential temperature
controller
φ12
120
49 80
63
TSD is differential temperature controller has
two thermo-bulbs to sense the differential φ2.5
temperature. After comparing the differential
temperature with the setting value, the
differential temperature controller will putout a
differential signal to make the temperature
controller work. The differential temperature
controller can keep a constant value of
differential temperature between two medium Dimension (unit: mm)
in general ventilation and some cooling devices.
The two relative thermo-bulbs, one is for
temperature reference, the other one is for
controlling signals. Differential temperature is
directly controlled parameters.
Specification 37
Differential temperature Setting the action differential temperature Working The highest temperature
Model setting range of the Min. differential temperature temperature range of thermo-bulb
Contact Form
3
1
5 Electrical Ranting
M
Rated Voltage (V)
A.C.110 A.C.220
Rated Current (A)
www.lefoo.com
φ
TSH
12 Dual temperature controller
108
49
120
63
φ2.5
Specification
Low side High side
Electrical Ranting
Rated Voltage (V)
A.C.110 A.C.220
Rated Current (A)
Contact Form
L 5 4 L 5 4 M L 5 4 M
1 3 1 3 1 3
2 6 H 2 6 H M 2 6 H
www.lefoo.com
Miniature pressure &
vacuum switch
1
φ
2-
φ19
φ4
25.5
19.2
39
Dimension in:mm
φ1
2-φ4
19.6
15.4
37 φ27
40 Dimension in:mm
34.5
φ31.8
30
1 2
G1/8
malethread s
1.5
20
Connector
Dimension in:mm
12
108
G1/4
80
68
88
Dimension in:mm
φ40
32.5
G1/8-28-A
Operating Logic
Switch tube output:differential output,pressure reduces from 0bar to -0.75bar,
in the process switch tube ON,load operates,when lower than -0.75bar,
switch tube OFF,load stops,when pressure up to -0.4bar switch tube works again.
bar
Open swith tube Close swith tube Open swith tube
run load shut off load run load
0
-0.4
-0.75
-1
44 Differential Output
Output LFDS704 is widely used in vacuum pump
control system of electric cars, diesel vehicle
Red DC(+)
and gasoline vehicles. LFDS704 has internal
MEMS pressure sensor, by collecting warming
Red DC(+) and comparing of pressure signal to realize the
switch tube output of special pressure point.
Major Load + The product uses pressure sensor that is
Loop
Black OUT DC12-30V absolute pressure type, the accuracy will not
-
affect by atmosphere, which can be used in any
Black DC(-) altitude. The product has differential output,
which reduces the risk of lifespan cutting of
controlled device for frequent action nearby
critical point.
Specification
Model LFDS704
Measurement Range -1.0~0bar
Accuracy ±2.0% FS
Overload Pressure Measurement Range×2
Bursting Pressure Measurement Range×4
Media Air and Non hazardous gas
Output Switch tube output
Pressure Type Absolute Pressure
Working Temperature -40~120℃
Compensation Temperature -20~85℃
Power Supply 12~30VDC
Operating Life >1000000 times
Response Time 20ms
Protection Grade IP66
Shell Material Al6061
Pressure Connection G1/8
Output Driving Capability ≤20.0A
Max Duration 18s
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
High pressure switch
Adjustmentscrew
Faston
Ch24
L2
L1
X3
Dimension in:mm
Body Pressure
Number Connection (X3) Diaphragm Circuitry
L1 L2
Material Range Tolerance
1 G1/8 B9 C 45 D NBR E Zinc-plated Steel F NO 0.1-1bar ±0.2bar
2 NPT1/8 9 45 FKM Stainless Steel NC G 1-5bar ±0.3bar
3 M10×1 9 45 EPDM / / 1-10bar ±0.5bar
4 UNF7/16 9 45 HNBR / / 10-20bar ±1bar
5 G1/4 9 45 / / / 20-50bar ±2bar
6 NPT1/4 9 45 / / / / /
7 G1/2 12 48 / / / / /
Specification
Model LF701A
Body Zinc-plated Steel/Stainless Steel
Contact Silver cadmium alloy, can be gold plated
Max Voltage 42V
Max Currency 4A
Working Temperature Range -40℃~+100℃ (baesd on different diaphragm)
Life Endurance 10 6
Electrical Life Endurance 10 5
Pollution Situation Normal
IP Level IP00(without cover)
With Cover IP54(rubber cover)
With Cover IP67(potting resin cover)
Applicable Rule EN 60730-1
Max Working Pressure 150bar
Burst Perssure 300bar
Weight ~85gr
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
Adjustmentscrew
High pressure switch
12.9
Faston6.3×0.8
Ch24
L2
L1
X3
Dimension in:mm
Body Pressure
Number Connection (X3) L1 L2 Diaphragm Circuitr y Tolerance
Material Range
1 G1/8 B9 C 55 D NBR E Zinc-plated Steel F NO 0.1-1bar ±0.2bar
2 NPT1/8 9 55 FKM Stainless Steel NC G 1-5bar ±0.3bar
3 M10×1 9 55 EPDM / / 1-10bar ±0.5bar
4 UNF7/16 9 55 HNBR / / 10-20bar ±1bar
5 G1/4 9 55 / / / 20-50bar ±2bar
6 NPT1/4 9 55 / / / / /
7 G1/2 12 58 / / / / /
Specification
Model LF701B
Body Zinc-plated Steel/Stainless Steel
Contact Silver cadmium alloy, can be gold plated
Max Voltage 42V
Max Currency 4A
Working Temperature Range -40℃~+100℃ (baesd on different diaphragm)
Life Endurance 10 6
Electrical Life Endurance 10 5
Pollution Situation Normal
IP Level IP00(without cover)
With Cover IP54(rubber cover)
With Cover IP67(potting resin cover)
Applicable Rule EN 60730-1
Max Working Pressure 150bar
Burst Perssure 300bar
Weight ~85gr
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
High pressure switch
Adjustmentscrew
Faston
Ch24
L2
L1
X3
Dimension in:mm
Body Pressure
Number Connection (X3) L1 L2 O"Ring Circuitry
Range Tolerance
Material
1 G1/8 B9 C 45 D NBR E Zinc-plated Steel F NO G 50-150bar ±10bar
2 NPT1/8 9 45 FKM Stainless Steel NC 100-200bar ±15bar
3 M10×1 9 45 EPDM / / / /
4 UNF7/16 9 45 HNBR / / / /
5 G1/4 9 45 / / / / /
6 NPT1/4 9 45 / / / / /
7 G1/2 12 48 / / / / /
Specification
Model LF702A
Body Zinc-plated Steel/Stainless Steel
Contact Silver cadmium alloy, can be gold plated
Max Voltage 42V
Max Currency 4A
Working Temperature Range -40℃~+100℃ (baesd on different diaphragm)
Life Endurance 10 6
Electrical Life Endurance 10 5
Pollution Situation Normal
IP Level IP00(without cover)
With Cover IP54(rubber cover)
With Cover IP67(potting resin cover)
Applicable Rule EN60730-1
Max Working Pressure 450bar
Burst Perssure 600bar
Weight ~85gr
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
High pressure switch
Adjustmentscrew
12.9
Faston6.3×0.8
Ch24
L2
L1
X3
Dimension in:mm
LF702B Order Ref NO Piston type pressure switch with 6.4mm plug
LF702B - 2 1 1 1 1 1 1 terminal and 600bar of maximum safety
48 AB CDE F G
pressure
Body Pressure
Number Connection (X3) L1 L2 O"Ring Circuitry Tolerance
Material Range
1 G1/8 B9 C 55 D NBR E Zinc-plated Steel F NO G 50-150bar ±10bar
2 NPT1/8 9 55 FKM Stainless Steel NC 100-200bar ±15bar
3 M10×1 9 55 EPDM / / / /
4 UNF7/16 9 55 HNBR / / / /
5 G1/4 9 55 / / / / /
6 NPT1/4 9 55 / / / / /
7 G1/2 12 58 / / / / /
Specification
Model LF702B
Body Zinc-plated Steel/Stainless Steel
Contact Silver cadmium alloy, can be gold plated
Max Voltage 42V
Max Currency 4A
Working Temperature Range -40℃~+100℃ (baesd on different diaphragm)
Life Endurance 10 6
Electrical Life Endurance 10 5
Pollution Situation Normal
IP Level IP00(without cover)
With Cover IP54(rubber cover)
With Cover IP67(potting resin cover)
Applicable Rule EN 60730-1
Max Working Pressure 450bar
Burst Perssure 600bar
Weight ~85gr
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
High pressure switch
40.7
ExternalCableφ5-7
CableClamp
2NC
1C
L2
4NO
Ch27 SPDTContacts
L1 X3
34.3
Regulationpressurescrew
Regulationdifferential
pressurescrew
Dimension in:mm
49
Diaphragm type pressure switch with DIN 43650- LF703 Order Ref NO
A Hirchmann connection, SPDT and 300bar of
maximum safety pressure LF703 - 2 1 1 1 1 1 1
B CDE FG
Body Pressure
Number Connection (X3) L1 L2 Diaphragm Circuitry Tolerance
Material Range
1 G1/8 B9 C 95 D NBR E Zinc-plated Steel F NO G 1-5bar ±0.3bar
2 NPT1/8 9 95 FKM Stainless Steel NC 1-10bar ±0.5bar
3 M10×1 9 95 EPDM / / 10-20bar ±1bar
4 UNF7/16 9 95 HNBR / / 20-50bar ±2bar
5 G1/4 9 95 / / / / /
6 NPT1/4 9 95 / / / / /
7 G1/2 12 98 / / / / /
Specification
Model LF703
Body Zinc-plated Steel/Stainless Steel
Contact Silver cadmium alloy, can be gold plated
Max Voltage 250VAC/24VDC
Max Currency 4A
Working Temperature Range -40℃~+100℃ (baesd on different diaphragm)
Life Endurance 10 6
Electrical Life Endurance 10 5
Pollution Situation Normal
IP Level IP65
Applicable Rule EN 60730-1
Max Working Pressure 150bar
Burst Perssure 300bar
Weight ~140gr
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
High pressure switch
40.7
ExternalCableφ5-7
CableClamp
2NC
1C
L2
4NO
Ch27 SPDTContacts
L1
X3
34.3
Regulationpressurescrew
Regulationdifferential
pressurescrew
Dimension in:mm
50 LF704 Order Ref NO Piston type pressure switch with DIN 43650-A
Hirchmann connection, SPDT and 600bar of
LF704 - 2 1 1 1 1 1 1 maximum safety pressure
BCDEFG
Body Pressure
Number Connection (X3) L1 L2 Diaphragm Circuitr y Tolerance
Material Range
1 G1/8 B9 C 95 D NBR E Zinc-plated Steel F NO G 50-150bar ±10bar
2 NPT1/8 9 95 FKM Stainless Steel NC 100-200bar ±15bar
3 M10×1 9 95 EPDM / / / /
4 UNF7/16 9 95 HNBR / / / /
5 G1/4 9 95 / / / / /
6 NPT1/4 9 95 / / / / /
7 G1/2 12 98 / / / / /
Specification
Model LF704
Body Zinc-plated Steel/Stainless Steel
Contact Silver cadmium alloy, can be gold plated
Max Voltage 250VAC/24VDC
Max Currency 4A
Working Temperature Range -40℃~+100℃ (baesd on different diaphragm)
Life Endurance 10 6
Electrical Life Endurance 10 5
Pollution Situation Normal
IP Level IP65
Applicable Rule EN 60730-1
Max Working Pressure 450bar
Burst Perssure 600bar
Weight ~140gr
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
High pressure switch
Adjustmentscrew
12.9
Faston6.3×0.8
Ch24
L2
L1
X3
Dimension in:mm
Diaphragm type pressure switch with 6.4mm plug LF705 Order Ref NO
terminal, brass body and 80bar of maximum LF705 - 2 1 1 1 1 2 51
safety pressure
BCDEF
Specification
Model LF705
Body Brass
Contact Silver cadmium alloy, can be gold plated
Max Voltage 42V
Max Currency 4A
Working Temperature Range -40℃~+100℃ (baesd on different diaphragm)
Life Endurance 10 6
Electrical Life Endurance 10 5
Pollution Situation Normal
IP Level IP00(without cover)
With Cover IP54(rubber cover)
With Cover IP67(potting resin cover)
Applicable Rule EN 60730-1
Max Working Pressure 40bar
Burst Perssure 80bar
Weight ~85gr
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
High pressure switch
Adjustmentscrew
Faston
Ch24
L2
L1
X3
Dimension in:mm
Specification
Model LF705A
Body Brass
Contact Silver cadmium alloy, can be gold plated
Max Voltage 42V
Max Currency 4A
Working Temperature Range -40℃~+100℃ (baesd on different diaphragm)
Life Endurance 10 6
Electrical Life Endurance 10 5
Pollution Situation Normal
IP Level IP00(without cover)
With Cover IP54(rubber cover)
With Cover IP67(potting resin cover)
Applicable Rule EN 60730-1
Max Working Pressure 40bar
Burst Perssure 80bar
Weight ~85gr
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
High pressure switch
40.7
ExternalCableφ5-7
CableClamp
2NC
1C
L2
4NO
Ch27 SPDTContacts
L1
X3
34.3
Regulationpressurescrew
Regulationdifferential
pressurescrew
Dimension in:mm
53
Diaphragm type pressure switch with DIN 43650- LF706 Order Ref NO
A Hirschmann connection, brass body and 80bar
of maximum safety pressure LF706 - 2 1 1 1 2
BCDE
Specification
Model LF706
Body Brass
Contact Silver cadmium alloy, can be gold plated
Max Voltage 42V
Max Currency 4A
Working Temperature Range -40℃~+100℃ (baesd on different diaphragm)
Life Endurance 10 6
Electrical Life Endurance 10 5
Pollution Situation Normal
IP Level IP00(without cover)
Applicable Rule EN 60730-1
Max Working Pressure 40bar
Burst Perssure 80bar
Weight ~140gr
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
Adjustmentscrew
High pressure switch
Faston6.3×0.8
Ch24
55
X3
Dimension in:mm
Body Pressure
Number Connection (X3) L1 L2 Diaphragm Circuitry Tolerance
Material Range
1 G1/8 B9 C 55 D NBR E Zinc-plated Steel F NO 0.1-1bar ±0.2bar
2 A M12×1.5 9 55 FKM Stainless Steel NC G 1-5bar ±0.3bar
3 M10×1 9 55 EPDM / / 1-10bar ±0.5bar
4 G1/4 9 55 HNBR / / 10-20bar ±1bar
5 / / / / / / 20-50bar ±2bar
Specification
Model LF707
Body Zinc-plated Steel/Stainless Steel
Contact Silver cadmium alloy, can be gold plated
Max Voltage 42V
Max Currency 4A
Working Temperature Range -40℃~+100℃ (baesd on different diaphragm)
Life Endurance 10 6
Electrical Life Endurance 10 5
Pollution Situation Normal
IP Level IP00(without cover)
With Cover IP54(rubber cover)
With Cover IP67(potting resin cover)
Applicable Rule EN 60730-1
Max Working Pressure 40bar
Burst Perssure 80bar
Weight ~105gr
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
High pressure switch
Adjustmentscrew
Faston6.3*0.8
Ch24
55
9
X3
Dimension in:mm
55
Specification
Model LF708
Body Brass
Contact Silver cadmium alloy, can be gold plated
Max Voltage 42V
Max Currency 4A
Working Temperature Range -40℃~+100℃ (baesd on different diaphragm)
Life Endurance 10 6
Electrical Life Endurance 10 5
Pollution Situation Normal
IP Level IP00(without cover)
With Cover IP54(rubber cover)
With Cover IP67(potting resin cover)
Applicable Rule EN 60730-1
Max Working Pressure 40bar
Burst Perssure 80bar
Weight ~105gr
Conversion: 1kgf/cm²=14.2psi 1bar=14.5psi
www.lefoo.com
Differential
pressure transmitter
35.5 97
87
φ6.2
PG9
77
77
77
Specification
General Value
Accuracy ±1.0%FS
Compensated temperatures -10~60℃
Zero/Full range deviation%FS/%C ±0.01
Over pressure capacity ×15
Output signal 0~5/10VDC\3-wire ; 4~20mA\2-wire
Supply voltage 0~5/10VDC\12~30VDC ; 4~20mA\10~30VDC
An external load 0~5/10VDC\≥50KΩ ; 4~20mA\≤250Ω
Response time 0.5s,1s,2s,4s
Compensation temperature -10~60℃
Operation Temperature -10~60℃ ; -40~85℃
Shell material Industrial plastic, flame retardant grade UL94-V0
Connection Metal agnail interface, Ø6.2mm
Cable connector Cable diameter Ø8mm
Weight 140g
104
φ6.2
PG9
75
40
60 top
14.7
A
40
.5
φ4
68
40
40
A
4.5
φ 7.5
0
Dimension in:mm
L o w D i f f e r e n t i a l P r e s s u r e Tr a n s m i t t e r
LFM110/LFM112 are engineered for building
automation in the HVAC/R industry , pressure LFM11 Series Order Ref NO
and flow monitoring, and low differential 57
pressure test in industry application. LFM110 - N - A - C
B C D
Span B Display C Output D Accuracy
0=-1000~1000Pa O=with display A=4~20mA ,0-5/10VDC ±1.0%FS
2=-10000~10000Pa N=without display B=4~20mA(2-wire)
6=-100~100Pa C=0~10VDC(3-wire)
D=0~5VDC(3-wire)
Specification
General Value
Accuracy ±1.0%FS
Unit Pa,mmH 2 O,mbar,inWG,mmHG,daPa,hPa
0~5/10VDC and 4~20mA simultaneous output,
Output signal
4~20mA 2-wire 0~5VDC 3-wire,0~10VDC 3-wire
Supply Voltage 16~30VDC/16~30VAC
Power Supply 1.5W
Response time 20ms,0.5s,1s,2s
LFM110:1Pa,1mmH2O,0.01mbar,0.04inWG,0.007mmHG,0.1daPa,0.001kPa
Resolution LFM112:0.01hPa
LFM116:0.1Pa,0.01mmH2O,0.001mbar,0.01daPa,0.001hPa
Zero Point adjustment Automatic with autozero element or with push button
Measuring unit Air or neutral gas
Operation Temperature -10~60℃
Storage Temperature -10~70℃
Range Capacity
-1000~1000Pa -15000~15000Pa
Over pressure capacity
-10000~10000Pa -150000~150000Pa
-100~100Pa -4500~4500Pa
Conversion: 1in W.C.=249Pa 1MPa=100Pa
www.lefoo.com
LFM3 Series
Differential pressure gauge
176
38
128
φ140
38
Dimension in:mm
Features
Non-polar Input: No need to differentiate the negative or positive input
voltage sourcing lead.
Excellent Material: housing made of FR-ABS, satisfactor y impact resistance
and heat resistance etc.
Span: 0~±100Pa/0~±1,000Pa / 0~±10,000Pa Accuracy: ±1.0%FS.
Various switchable pressure units.
Big LCD screen. LFM3 Series differential pressure gauge use
Manual button of zero calibration. imported high precision sensor and digitalization
58 Manual button of default reset. technology. They are easy installation, LCD
Max. and min pressure value to review. display, clear and accurate reading, and can be
Settable response time.
applied to measure fan and blower pressures,
Built-in buzzer with sound-light alarm, field programmable alarm pressure value.
Imported chip. filter resistance, air velocity, furnace draft,
The Max. and Min. pressure range of discrete output can be set(only LFM32 Series). pressure drop across orifice plates and medical
care equipment. This series have three optional
LFM3 Order Ref NO discrete output versions (relay, NPN and PNP),
LFM30-0-W-P-B can be flexibly applied to control the external
equipments.
B C D E
~118
φ27
~81
φ24
56
67.5
φ21.6
27
34.5
S27
46
S24
20
S22
14
M20×1.5 7/16-20UNF-2B
G1/4
Dimension in:mm
The heart of T2000 pressure transmitter is a
ceramic pressure sensor that is temperature
compensated and laser trimmed for accurate
span and offset calibration. The typical T2000 Order Ref NO
advantage is the compact size, which make it
convenient to be installed in small room.
T2000-A4-0~4······60-B-1.5-P-G-1.0
B C D E F G
20
S27
φ28
101
φ27
~125
~133
77
Measurement range(mH 2 O)
B Output: A4 = 4~20mA ; V05 = 0.5~4.5V; V0 = 0~5V; V1 = 1~5V; V10 = 0~10V
C Accuracy: 0.25=0.25%F.S; 0.5=0.5%F.S
D Pressure connection: G=G1/4; T=Dive type
E Cable length(m)
Specification
General Value
Measurement Range 0~1······500mH 2 O
Overload Pressure 1.5 times of full scales
Burst Pressure 3 times of full scales
Accuracy ±0.25%F.S、±0.5%F.S
Long Term Stability Typical value: 0.1%F.S Maximum: 0.2%F.S
Working Temperature -40℃~85℃
Compensated Temperature -10℃~70℃
Medium Compatibility All corrosive medium compatible with 1Cr18Ni9Ti and 316L
Output Mode Two-wired Three-wired
Output 4~20mA 0.5~4.5V 0/1~5V 0~10V
Power Supply 12~36VDC 5VDC 10~36VDC/AC 12~36VDC/AC
Load Resistance (U-10)/0.02(Ω) >100K(Ω)
Insulation >100M(Ω)@50V
Electrical Connection Waterproof cover+Two rectangular ring+Seal ring+Sealant+Glue,Protection: IP68
Pressure Connection G1/4 thread or Dive type
Response Time 10ms
Pressure Form Gauge pressure
Electromagnetic Compatibility Electromagnetic transmit: EN50081-1/-2; Electromagnetic sensitivity: EN50082-2
Air conduction voltage 8000V,shell or cable conduction voltage 4000V;
Lightning-proof
Can also be provided acording to customer ’s requirement
www.lefoo.com
T3800
Digital
pressure transmitter G1/4
12
14
S27
φ28
107
φ27
~131
~127
77
Dimension in:mm
Specification
General Value
Measure Range 0~2······200mH20
Overload Pressure 1.5 times full scale
Broken Pressure 3 times full scale
Accuracy ±0.5%F.S
Stability Typical 0.2%F.S per year
Operating Temperature -40℃~85℃
Medium Compatibility Corrosive medium compatible with stainless steel Cr18Ni9Ti
Signal Output Rs485
Power Supply 10~30Vdc
Insulation >100M Ω@50V
Electrical connection Waterproof solid line sets
Pressure connection Investment style, Threaded: M20×1.5、G1/4、G1/2、R1/2、NPT1/2
Pressure type Gauge G, Sealed gauge S
Response Time 10ms
Electro Magnetic Compatibility EM: EN50081-1/-2; EMS: EN50082-2
www.lefoo.com
T1500
49
Differential
pressure transmitter
φ27
~140
φ27
~114
G1 / 4
φ32
G1 / 4
φ32
φ40
φ40
G1/4
G1/4
12 40 12 12 40 12
84 84
T1500 differential pressure transmitter is
characterized by anti-electromagnetic
Dimension in:mm interference and lighting proof. It is widely used
in liquid and water differential pressure test.
Such as flow test. Water swage treatment, mine
download differential pressure test. Water heat
T1500 Order Ref NO of hydropower station city flood control and
drainage, under water engineering, under water
T1500-A4-100-K-0.25-H-GF-1.0 test,water saving irrigation, terminal control of
B C D E F G central air-conditioning, ect.
Specification
General Value
Measurement Range 0~±5kPa······±5000kPa
Overload Pressure 1.5 times of full scales
Burst Pressure 3、5、10 times of full scales, 20MPa
Accuracy ±0.25%F.S、±0.5%F.S
Long Term Stability Typical value: 0.1%F.S Maximum: 0.2%F.S
Working Temperature -40℃~85℃
Compensated Temperature -10℃~70℃
Medium Compatibility All corrosive medium compatible with 1Cr18Ni9Ti and 316L
Output Mode Two-wired Three-wired
Output 4~20mA 0/1~5V 0~10V
Power Supply 12~30VDC 8~36VDC/AC 11~30VDC/AC
Load Resistance (U-10)/0.02(Ω) >100K(Ω)
Insulation >100M(Ω)@50V
Electric strength 500V@60 second
Impulse current 10g/5~2000Hz,axes X/Y/Z20g sine 11ms
Protection class water resistant wire leads,IP68;DIN43650,cover IP65
Response Time 10ms
Pressure endurance 2×106 pressure circles@25℃
Electromagnetic Compatibility Electromagnetic transmit:EN50081-1/-2;Electromagnetic sensitivity:EN50082-2
Air conduction voltage 8000V, shell or cable conduction voltage 4000V;
Lightning-proof
Can also be preovided according to customer ’s requirement
Conversion: 1bar=14.5psi=100kPa
www.lefoo.com
T1050
High accuracy
pressure transmitter
~118
φ27
~81
S27
T1050 series are the cost effective products
featuring mass production, low cost, extensive
20
application for industrial and civil product. It’s
widely used for measuring the pressure of gas
and liquid, such as water, oil and mild corrosive M20×1.5
liquid and gas.
The product is made of 1Cr18Ni9TI stainless steel
and with selected pressure sensing elements
which is from well-known international brand. Dimension in:mm
The special circuits for V/I adaptor makes the
zero and full range calibration more convenient.
Non-polar two-wire current and three-wire
AC/DC voltage output are provided.Customized T1050 Order Ref NO
structures and output formats can be designed
according to special application requirements, in T1050-A4-1.0-M-0.25-H-G-1.0
addition to standards products. B C D E F G
63
Output: A4=4~20mA ; V05=0.5~4.5V; V0=0~5V; V1=1~5V; V10=0~10V
B Measurement range
C Unit of measure: K = kPa; M = MPa; P = psi; B = bar
D Accuracy: 0.25=±0.25%F.S; 0.5=±0.5%F.S
E Electrical connector: H=DIN43650-A ; GX=GX16-7; C=Cable
F Pressure connection: G=G1/4; N=NPT1/4; R=R1/4; U=7/16-20UNF; M=M20×1.5; N2=NPT1/2; G2=G1/2; R2=R1/2
G Cable length(m)
Specification
General Value
Measurement Range 0~2······600bar
Overload Pressure 1.5 times of full scales
Burst Pressure 3 times of full scales
Accuracy ±0.5%F.S
Long Term Stability Typical value: 0.25%F.S Maximum: 0.4%F.S
Working Temperature -40℃~85℃
Compensated Temperature -10℃~70℃
Medium Compatibility ALL corrosive medium compatible with 1Cr18Ni9TI
Output Mode Two-wired Three-wired
Output 4~20mA 0.5~4.5V 0/1~5V 0~10V
Power Supply 12~30VDC 5VDC 10~30VDC/AC 12~30VDC/AC
Load Resistance (U-10)/0.02(Ω) >100K(Ω)
Insulation >100M(Ω)@50V
Electrical Connection Packard, DIN 43650C, DIN72585, M12, Cable
Pressure Connection Male G1/4,G1/2,NPT1/4,NPT1/2,M20×1.5
Response Time 10ms
Pressure Form Gauge pressure
Electromagnetic Compatibility Electromagnetic transmit:EN50081-1/-2;Electromagnetic sensitivity:EN50082-2
Conversion: 1bar=14.5psi 1MPa=10bar
www.lefoo.com
T1030
High accuracy
pressure transmitter
~138
φ27
~101
S27
20
M20×1.5
Dimension in:mm
Specification
General Value
Measurement Range -1······-0.1bar~0~0.1······1000bar
Overload Pressure 1.5 times of full scales
Burst Pressure 3 times of full scales
Accuracy ±0.25%F.S、±0.5%F.S
Long Term Stability Typical value: 0.25%F.S Maximum: 0.4%F.S
Working Temperature -40℃~85℃
Compensated Temperature -10℃~70℃
Medium Compatibility ALL corrosive medium compatible with 1Cr18Ni9TI
Output Mode Two-wired Three-wired Four-wired
Output 4~20mA 0~20mA\0~10VAC 0/1~5V 0.5~3/4.5V 0~20mA、0~5/10VDC
Power Supply 10~30VDC 11~30VDC 8~24VDC 5V Ratio 8/11~30VDC
Load Resistance (U-10)/0.02(Ω) Current model: (U-12)/0.02(Ω); Voltage model: >20K(Ω)
Insulation >100M(Ω)@50V
Electrical Connection DIN63650,IP65;GX16-7,IP45;Wire,IP68
Pressure Connection G1,G1/4,G1/2,NPT1/4,NPT1/2,R1/4,M20×1.5,(Ht)
Response Time 10ms
Electromagnetic Compatibility Electromagnetic transmit: EN50081-1/-2; Electromagnetic sensitivity: EN50082-2
Conversion: 1bar=14.5psi 1MPa=10bar
www.lefoo.com
T1700
Pressure transmitter
~138
φ27
~101
S27
20
M20×1.5
Dimension in:mm
T1700 series pressure transmitter is used for
absolute vacuum measuring control, which has
fully solved the problem of difficult vacuum T1700 Order Ref NO
m e a s u re m e n t . A l l t h e e x i s t i n g p re s s u re
connections and electrical connections are T1700-A4-1.0-M-0.25-H-G-1.0
available for T1700 series pressure transmitter. B C D E F G
~138
φ27
~101
Specification
General Value
Measuring Range 0~1······2000bar
Overload capability 2 times full scale
Burst pressure 4 times full scale
Accuracy ±0.1%F.S、±0.25%F.S、±0.5%F.S
Stable typically 0.25%F.S per year, 0.4%F.S(Max) per year
Medium temperature range -50℃~150℃ (-50℃~230℃ is available on requrest)
Compensated Temperature -20℃~120℃
Medium Liquids and gases, compatible with stainless steel1Cr18Ni9Ti
Electrical overview 2 wire 3 wire 4 wire
Output 4~20mA 0~20mA 0~10mA 0~5/10V
Power Supply 12~30VDC 12~30VDC 12~30VDC
Load (U-10)/0.02(Ω) (U-10)/0.02(Ω) >20K(Ω)
Insulation reistance >100M(Ω)@50V
Insulation voltage 500V@60 second
Vibration /Constant shock 10g/5~2000Hz, axes X/Y/Z20g sine 11ms
Life 2×106 cycles @25℃
Electrical Connection DIN43650C, M12 Series, Packard, Cable
Pressure connection M20×1.5、G1/4、G1/2、R1/2、NPT1/2、NPT1/4
Pressure Type Guage, Seal Guage, Abosolute
Electro Magnetic Compatibility EN50081-1/-2, EN50082-2
Conversion: 1bar=14.5psi 1MPa=10bar
www.lefoo.com
Engine oil pressure sensor
.5
44
φ
19
75
61.1
25
67
Dimension in:mm
Specification
Model YG2221E
Measuring Range 0~6bar
Output 90~200Ω(other range is available on request)
Supply Power 12/24VDC
Alarm Pressure 0.8bar
Pressure Type Absolute Pressure
Operation Temperature Range -30℃~130℃
Sample Line Connection 1/4NPT(other connection is available on request)
Electrical Connection G-Pressure Meter, WK-Alarm
Conversion: 1bar=14.5psi 1MPa=10bar
www.lefoo.com
SVD20
Inlet Solenoid Valve
63.5
25
59.1
25
36
1/4"
46
25
59.1
25
36
NPT1/4
68 61.2
25
59.1
25
36
www.lefoo.com
LFSV20-B
Drainage
Solenoid Valve
M5
↓14
25
15
ZG1/2-14
77.5
76
ZG1/2-14
G1/2-14
25
12
34.5 46
69
Dimension in:mm
Specification
Model LFSV20-B
Media Water
www.lefoo.com