FLUID

NOMENCLATURE SERVICE DESIGN CONDITIONS

AD MILL AIR 0 - 125 psig

AE ESSENTIAL AIR 40F - 200F
AI INSTRUMENT AIR
AM MILL AIR APPLICABLE CODE
AP PADDING AIR ASME B31.3
Category D Fluid Service

ITEM DESCRIPTION SPECIFICATION

PIPE Material: Austenitic SS, welded ASTM A312

2” & Less End Prep: Plain ends Gr. TP 304L
Wall Thk: Schedule 10S

2½” - 12” Material: Austenitic SS, welded ASTM A312

End Prep: See Note 9 Gr. TP 304L
Wall Thk: Schedule 10S

NIPPLES Material: Austenitic SS, welded ASTM A312

2” & Less End Prep: Threaded Gr. TP 304L
Wall Thk: Schedule 40S

FITTINGS Material: Cast SS ASTM A351

2” & Less Conn: Socket weld Gr. 304L
(See Note 13) Class: 3000 MSS SP-114

2½” - 12 Material: Austenitic SS ASTM A403

Conn: Butt weld Gr. CR 304L
Wall Thk: Schedule 10S MSS SP-43

FLANGES Material: Austenitic SS, forged ASTM A182

2” & Less Conn: Socket weld Gr. F304L
Class: 150 ASME B16.5

2½” - 12” Material: Austenitic SS, stub ends, Type A MSS ASTM A403 Gr. CR 304L
length with CS Class 150 lap joint MSS SP-43
flange ASTM A105
Conn: Butt weld ASME B16.5
Wall Thk: Schedule 10S

BOLTS & NUTS Material: Carbon steel ASTM A307 Gr. B for bolts
All Sizes Type: Unified inch screw threads, UNC< ASTM A563 Gr. A for nuts
Class 2 fit with heavy hex nut ASME B1.1
ASME B18.2.1 & B18.2.2

DESIGN STANDARD
4C-03.01 S1 0
ISSUED FOR
PROJECT NO. SHEET 1 OF 4 Rev.
CMPC PULP PROJ.
G.Navarrete
DATE OF
APPR. ISSUE

DEPT. GENERIC
APPR.
P.Strodthoff APPR. DATE NOV 2020
GASKETS Material: CMPC Gasket Table by Standard

BRANCH CONNECTIONS Material: Cast SS ASTM A351

2” & Less Type: Couplings, half couplings Gr. 304L
Conn: Socket weld MSS SP-114
Class: 3000

INSTRUMENT FITTINGS Material: Forged SS ASTM A182

2” & Less Conn: Threaded Gr. F304L
Type: 45 latrolets & elbolets ANSI B16.11
Class: 3000

Material: Cast SS ASTM A351

Conn: Threaded Gr. 304L
Type: Couplings & half couplings MSS SP-114
Class: 150

LUBRICANTS Type: Graphite, calcium fluoride base Fel-Pro heavy duty anti-seize
for bolts and gaskets or approved equal

Type: Fast curing thread sealant with teflon, Loctite PST-567

for pipe threads or approved equal

VALVE DESCRIPTION VALVE NO.

BALL Material: 316 SS lever operator V-4121

1” & Less(Instrument only) Conn: Threaded
Class: 150

BALL Material: 316 SS lever handle, 3 piece full port, V-4294

1½” - 2” teflon seat c/w lock out lug
Conn: Socket weld
Class: 300

CHECK Material: Cast SS 316 body, swing bolted bonnet V-3222

1” & Less Threaded
Conn: 150
Class:

CHECK Material: Cast SS 316 body, swing bolted bonnet V-3451

1½” & 2”  Socket weld
Conn: 300
Class:

GATE Material: Cast iron, bronze trim V-1131

DESIGN STANDARD
4C-03.01 S1 0
ISSUED FOR
PROJECT NO. SHEET 2 OF 4 Rev.
CMPC PULP PROJ.
G.Navarrete
DATE OF
APPR. ISSUE

DEPT. GENERIC
APPR.
P.Strodthoff APPR. DATE NOV 2020
2½” & Up Conn: Flanged
(See Note 4) Class: 125

CHECK Material: Cast iron body, aluminum bronze V-3135

2 ½” & Up plates, Buna ‘N’ seal, SS 316 springs
Conn: Flanged
Class: 125

BUTTERFLY Material: Cast iron body & disc, hard back, Buna V-9231
2½” - 6” ‘N’ seat & ‘O’ ring seals throttle type
handle
Conn: Flanged
Class: 150

INSTRUCTIONS: Fabrication of austenitic stainless steel pressure Standard 4S-02.01

piping (see Note 8)

Pipe line field erection, checking, testing and Standard 4S-20.01

cleaning specification

Instrument connections for steel pipe Standard 4D-10.02

Moisture trap assembly for air lines Standard 4D-17.06

NOTES:
1. All listed specifications and standards shall conform to the latest edition.

2. All pipe threads shall be cleaned in solvent to remove any cutting lubricant or grease.

3. Instrument air lines shall be pneumatically tested and blown with dry, oil-free air.

4. Gate valves that are located in inaccessible locations, shall be provided with chain operators or valve
extensions as required (as shown on drawings).

5. The inert gas shielded arc welding process (TIG) with shielding gas protection on the underside of the
weld shall be used in welding stainless steel instrument lines.

6. Branch connections shall connect to the top of horizontal headers and shall have shut off valves at the
headers.

7. Drain valves shall be located at the low end of sloped headers and at low points in the piping system.

8. The wall thickness specified in Standard 4S-02.01 shall not apply.

9. The end prep. for pipe and fittings shall be in accordance with paragraph 7.5 of design standard 4S-
02.01.

DESIGN STANDARD
4C-03.01 S1 0
ISSUED FOR
PROJECT NO. SHEET 3 OF 4 Rev.
CMPC PULP PROJ.
G.Navarrete
DATE OF
APPR. ISSUE

DEPT. GENERIC
APPR.
P.Strodthoff APPR. DATE NOV 2020
 10. Reducers on horizontal mill air pipe runs shall be eccentric in order to keep the bottom of the pipe flat.

11. N/A

12. Provide moisture traps at 250’ intervals along long horizontal runs and at bottom of vertical change in
direction.

13. Includes the use of swaged nipples in any combination of ends within the confines of this class sheet.
See design standard 4D-03.02.

14. V-3451 and V-4454 to be used only in headers as branch isolation valves.

DESIGN STANDARD
4C-03.01 S1 0
ISSUED FOR
PROJECT NO. SHEET 4 OF 4 Rev.
CMPC PULP PROJ.
G.Navarrete
DATE OF
APPR. ISSUE

DEPT. GENERIC
APPR.
P.Strodthoff APPR. DATE NOV 2020