C7 CableAccess
C7 CableAccess
C7 CableAccess
CABLE
ACCESSORIES
Cable
Accessories
Table of Contents
INSIDE.................................................................................PAGE
Reference Material....................................................70-71
GENERAL INFORMATION
RATINGS
Hubbell 15 kV, 200 A Separable Connectors are fully Max. continuous voltage................. 8.3 kV phase-to-ground
14.4 kV phase-to-phase
shielded, insulated, and submersible products that
Continuous current.......................... 200 A rms
provide a means to mate or disconnect cable to
switchgear, transformers, or sectionalizing equipment
on power distribution systems. They are designed
SHORT-TIME CURRENT RATINGS
for pad-mounted or subsurface applications, where 0.17 seconds duration...................... 10,000 A rms symmetrical
the components may be exposed to direct sunlight or 3.00 seconds duration...................... 3,500 A rms symmetrical
continuously submerged in water up to 6 feet (2m).
Elbows can be supplied with a capacitive test point that allows for the
installation of faulted circuit indicators and will indicate the presence of
voltage when interrogated with a high-impedance meter.
The integral seal elbow eliminates the need for a separate sealing
kit. The integral seal elbow is supplied with mastic strips to form a
barrier around the neutral wires. There are external grip hooks on
the integral seal elbow boot for easier installation.
Select a connector code that identifies the conductor size and stranding.
The elbow can be supplied with a separate, cold-shrink seal kit for
jacketed concentric neutral cable, or it can be furnished with a separate
adapter kit for copper tape shield cables.
Components:
215LBP Probe kit complete with pin wrench
200LUGBx Standard, long bi-metal lug
200LUGPx ProbeLok lug
200LUGCx All copper lug
To have a bushing insert packaged with the elbow, add ‘BI’ to the end of the part number. For example: 215LEJ45BI.
625SK52 Cold Shrink Cable Seal Kit for JCN cable with an overall diameter of 0.95” to 1.94”
625SK60 Tape Shield Adapter Kit for cable with an overall diameter of 0.83” to 1.95”
Example: Integral seal elbow for 1/0 stranded, 175 mil cable with a test point is: 215LEJ45T
2 1 5 L E
*These ranges are taken from the AEIC/ICEA industry cable standards
The Hubbell Loadbreak Bushing Insert meets all requirements of IEEE Std. 386. It is designed for installation on
transformers, switches or other equipment having a 200 A bushing well that meets the requirements of IEEE Std.
386, Interface 3. When mated with a comparably rated elbow or other accessory, the bushing insert provides a fully
shielded and submersible connection. The bushing insert contains an all-copper current path from the female contact
to the bushing well and internal connection to the switch or transformer.
215BI
Bushing Insert
Internal hex broach accepts a 5/16” wrench for proper
installation torque.
215FTI
Feed-thru Insert
Creates a tap position in an existing apparatus
215SB
Standoff Bushing
Provides a temporary or permanent parking position for energized
loadbreak elbows. The bracket permits mounting on the apparatus
parking stand.
215FT
Feed-thru - Horizontal Bracket
and
215FTV
Feed-thru - Vertical Bracket
A two-position junction in a bracket that can be installed on the
apparatus parking stand. Provides a means to test, phase, ground,
or park an energized elbow. They can also be used to by-pass a
transformer or to add arrester protection at the open point.
225TR
Test Rod
Fits into loadbreak bushings, junctions, and other products that
contain a loadbreak interface and is used with test meters to
determine if the circuit is energized or not.
SL150
Silicone Lubricant
Silicone lubricant for all separable connectors. Supplied
in a 5.3 oz (150 g.) tube. Sold in cartons of 24 tubes.
215GB
Grounded Bushing
Provides a temporary ground. Contains a fully functioning
loadbreak mechanism and has a fault current rating of
10,000 A for 10 cycles. Can be installed with a hotstick.
T6003091
Grounding Bushing with Clamp
This set includes a loadbreak bushing and bronze T6000466
ground clamp connected by a 4-ft. yellow 1/0 cable. A tin-
plated copper connector joins the cable to the bushing. A
threaded copper ferrule connects the cable to the clamp.
Fault current rating for each set: 10,000 A for 10 cycles.
C6000729
Grounding Elbow
Each set includes a yellow elbow, 6 feet of 1/0 copper
grounding cable with yellow jacket, and bronze T6000466
ground clamp. Fault current rating for each set: 10,000 A
for 10 cyles.
C6003102
Three-Phase Grounding Elbow Sets for
Switches & Transformers
Each set includes a three-way terminal block assembly, three 6-ft.
lengths of 1/0 copper ground cable with yellow jacket, a bronze
T6000466 ground clamp and three elbows. Fault current rating for
each set: 10,000 A for 10 cycles.
2 1 5 J
2 = 2 Position
3 = 3 Position
4 = 4 Position
B = With Bracket
U = With U-Straps
JUNCTION DESCRIPTION
Hubbell junctions are used to sectionalize cables or as center. Yellow seating indicator rings provide a positive
feed-thrus for making lateral taps. indication that the mating product is fully installed.
They are available in two, three and four tap units and, Junctions with the corrosion-resistant stainless steel
when connected with loadbreak elbows, have ratings mounting bracket allow back plate mounting angles of
as shown on the 15 kV Loadbreak Product Ratings & 30, 45, or 60 degrees. This bracket can be adjusted for
Specifications sheet. horizontal mounting to a flat surface. Junctions can also
be ordered with only U-straps for surface mounting.
Each tap works independently of the others contained
on the same unit. Adjacent taps are 3.24 inches center to
Performance
215US1 Junction U-strap, Stainless Steel w/Hardware
15 kV LOADBREAK JUNCTIONS 100% factory tested for Partial Discharge and either AC 60 Hz
(34 kV for 60 Sec.) or Impulse (BIL) (95 kV 1.2 x 50 μSec. wave).
A
3.24 IEEE STD 386 INTERFACE 5
TYP
8.4
4.6
CATALOG # POINTS A B C
Part Number No. Positions 2
215J2B A 13.9 B 2.0 C
16.9
215J3B 3 20.3 4.4 19.7
215J2B 2
215J4B 4 13.9 23.5 2.0 7.7 16.9
22.8
215J3B 3 20.3 }
4.4 19.7
HUBBELL POWER SYSTEMS, Inc.
215J4B 4 23.5 POWER SYSTEMS, INC
7.7 22.8
200A 15kV JUNCTION
TITLE
SB -- 0
WITHOUT THE WRITTEN CONSENT OF
HUBBELL POWER SYSTEMS.
HUBBELL POWER SYSTEMS UNPUBLISHED 215JXB
REV DATE DO NOT SCALE
DRN BY BvB 1 OF 1
ALL RIGHTS RESERVED UNDER THE
11/20/18 C OPYRIGHT LAWS. THIS DRAWING
DATE 11/20/18 SHEET
15 kV Standoff Bushing
A 215SB
B E
15 kV Bushing Insert
15 kV Elbow 215BI
215LExx E
CAUTION:---
15 kV Feed-Thru
215FTx
C E
15 kV Junction w/ U-Strap
215JxU
15 kV Elbow Arrester
215ELAxx E
15 kV Feed-Thru Insert
215FTI
E
D
15 kV Parkingstand Arrester
215PLAxx
E
GENERAL INFORMATION
RATINGS
Hubbell 25/28 kV, 200 A Separable Connectors are Max. continuous voltage................. 16.2 kV phase-to-ground
fully shielded, insulated, and submersible products 28.0 kV phase-to-phase
Continuous current.......................... 200 A rms
that provide a means to mate or disconnect cable to
switchgear, transformers, or sectionalizing equipment
on power distribution systems. They are designed
SHORT-TIME CURRENT RATINGS
for pad-mounted or subsurface applications, where
the components may be exposed to direct sunlight or 0.17 seconds duration...................... 10,000 A rms symmetrical
3.00 seconds duration...................... 3,500 A rms symmetrical
continuously submerged in water up to 6 feet (2m).
Elbows can be supplied with a capacitive test point that allows for the
installation of faulted circuit indicators and will indicate the presence of
voltage when interrogated with a high-impedance meter.
Bi-metal compression lug meets all requirements of ANSI Std. C119.4 for
Class A connectors.
The integral seal elbow eliminates the need for a separate sealing kit.
The integral seal elbow is supplied with mastic strips to form a barrier
around the neutral wires. There are external grip hooks on the integral
seal elbow boot for easier installation.
Select a connector code that identifies the conductor size and stranding.
The elbow can be supplied with a separate, cold-shrink seal kit for
jacketed concentric neutral cable, or it can be furnished with a separate
adapter kit for copper tape shield cables.
Components:
225LBP Probe kit complete with pin wrench
200LUGBx Standard, long bi-metal lug
200LUGPx ProbeLok lug
200LUGCx All copper lug
To have a bushing insert packaged with the elbow, add ‘BI’ to the end of the part number. For example: 228LEJ45BI.
625SK52 Cold Shrink Cable Seal Kit for JCN cable with an overall diameter of 0.95” to 1.94”
625SK60 Tape Shield Adapter Kit for cable with an overall diameter of 0.83” to 1.95”
Example: Integral seal elbow for 1/0 stranded, 260 mil cable with a test point is: 228LEJ45T
2 2 8 L E
The Hubbell Loadbreak Bushing Insert meets all requirements of IEEE Std. 386. It is designed for installation on
transformers, switches or other equipment having a 200 A bushing well that meets the requirements of IEEE Std.
386, Interface 3. When mated with a comparably rated elbow or other accessory, the bushing insert provides a fully
shielded and submersible connection. The bushing insert contains an all-copper current path from the female contact
to the bushing well and internal connection to the switch or transformer.
225BI
Bushing Insert
Internal hex broach accepts a 5/16” wrench for proper
installation torque.
228FTI
Feed-thru Insert
Creates a tap position in an existing apparatus
9U01BEW500
Insulating Cap
Used as a temporary or permanent cover on an energized operating
interface. Standard product has an insulating cuff. The insulating cap
is supplied with a 36-inch long lead for grounding.
228SB
Standoff Bushing
Provides a temporary or permanent parking position for energized
loadbreak elbows. The bracket permits mounting on the apparatus
parking stand.
228FT
Feed-thru - Horizontal Bracket
and
228FTV
Feed-thru - Vertical Bracket
225TR
Test Rod
Fits into loadbreak bushings, junctions, and other products that
contain a loadbreak interface and is used with test meters to
determine if the circuit is energized or not.
SL150
Silicone Lubricant
Silicone lubricant for all separable connectors. Supplied in a 5.3
oz (150 g.) tube. Sold in cartons of 24 tubes.
225GB
Grounded Bushing
Provides a temporary ground. Contains a fully functioning
loadbreak mechanism and is designed to handle one fault-
close of up to 10,000 A for 10 cycles. Can be installed with a
hotstick.
T6003092
Grounding Bushing with Clamp
This set includes a loadbreak bushing and bronze T6000466
ground clamp connected by a 4-ft. yellow 1/0 cable. A tin-
plated copper connector joins the cable to the bushing. A
threaded copper ferrule connects the cable to the clamp.
Fault current rating for each set: 10,000 A for 10 cycles.
T6002131
Grounding Elbow
Each set includes a yellow elbow, 6 feet of 1/0 copper
grounding cable with yellow jacket, and bronze T6000466
ground clamp. Fault current rating for each set: 10,000 A for
10 cyles.
C6003103
Three-Phase Grounding Elbow Sets for Switches
& Transformers
Each set includes a three-way terminal block assembly, three 6-ft.
lengths of 1/0 copper ground cable with yellow jacket, a bronze
T6000466 ground clamp and three elbows. Fault current rating for
each set: 10,000 A for 10 cycles.
2 2 8 J
2 = 2 Position
3 = 3 Position
4 = 4 Position
B = With Bracket
U = With U-Straps
JUNCTION DESCRIPTION
Hubbell junctions are used to sectionalize cables or as seating indicator rings provide a positive indication
feed-thrus for making lateral taps. that the mating product is fully installed and assists in
minimizing no-load, partial vacuum flashovers.
They are available in two, three and four tap units and,
when connected with loadbreak elbows, have ratings Junctions with the corrosion-resistant stainless steel
as shown on the 25/28 kV Loadbreak Product Ratings & mounting bracket allow back plate mounting angles of
Specifications sheet. 30, 45, or 60 degrees. This bracket can be adjusted for
horizontal mounting to a flat surface. Junctions can also
Adjacent taps are 4.0” center to center. Vented yellow be ordered with only U-straps for horizontal surface
mounting.
Performance
228US1 Junction U-strap, Stainless Steel w/Hardware
[X1]
.83
U-Strap Dimensions
5.00
3.36
[X2]
.50
[B1] (2) .33 x
.41 Slots
8.13
[B2]
[B2]
[B3]
6.86
Inside Bracket Feet Dimensions
U-Strap Dimensions
[X1]
8.13
10.86
[B4] 8.13
[B5]
[B5]
[B6] 14.86
25/28 kV Feed-Thru
228FT
The Hubbell Fused Elbow provides a quick and cost effective solution
for adding fused reliability to underground distribution systems. When
mated with a comparable loadbreak bushing, or other devices with an in-
terface that conforms to IEEE Std. 386, the Hubbell Fused Elbow provides
a fully shielded and submersible connection.
All Hubbell Fused Elbows are designed and tested to meet the require-
ments of IEEE Std. 386.
Select a connector code that identifies the conductor size and stranding.
The elbow can be supplied with a separate, cold-shrink seal kit for
jacketed concentric neutral cable, or it can be furnished with a separate Cable Dimension Reference
adapter kit for copper tape shield cables.
Components:
625SK52 Cold Shrink Cable Seal Kit for JCN cable with an overall diameter of 0.95” to 1.95”
625SK60 Tape Shield Adapter Range - 0.83” to 1.95”
200FEKITCx To order replacement hardware for installation of a Cooper™ fuse, determine the
connector code using chart on the next page
200FEKITHx To order replacement hardware for installation of a Hi-Tech® fuse, determine the
connector code using chart on the next page
Example: 28 kV Fused elbow using Hi-Tech® fuse for 1/0 stranded 260mil cable is: 228FEHB5
2 F E
15 = 15 kV Voltage Class
28 = 25/28 kV Voltage Class J = Seal Kit
S = Shield Adapter Kit
Blank = Neither
C = Cooper™ Fuse
H = Hi-Tech® Fuse
(1) Contact the factory for recommendations for use on PRODUCTION TESTS
ungrounded, resistance grounded, or delta systems. 100% factory test for partial discharge and either AC HI-POT (50 kV
for 60 seconds) or impulse (BIL) (150 kV 1.2 x 50 µsec. wave).
The elbow can be supplied with a separate, cold-shrink seal kit for jacketed concentric neutral cable,
or it can be furnished with a separate adapter kit for copper tape shield cables.
Components:
236LBP Probe kit complete with pin wrench
200LUGBx Standard, long bi-metal lug
200LUGPx ProbeLok lug
200LUGCx All copper lug
625SK52 Cold Shrink Cable Seal Kit for JCN cable with an overall diameter of 0.97” to 1.95”
625SK60 Tape Shield Adapter Range - 0.83” to 1.95”
Example: Loadbreak elbow for 1/0 stranded, 345 mil cable with a test point is: 236LE55T
2 3 6 L E 5
C = Copper Lug
P = ProbeLok Lug
Blank = Without
*These ranges are taken from the AEIC/ICEA industry cable standards
PRODUCTION TESTS
100% factory test for partial discharge and either AC HI-POT
(45 kV for 60 seconds) or impulse (BIL) (125 kV 1.2 x 50 μsec. wave).
The Hubbell Power Systems 600 A 25/28 kV rated The T-body can be ordered with or without a capacitive
Deadbreak Bolted T-body System is designed to test point.
terminate medium voltage underground distribution Bolted T-body systems provide an economical means of
cable to switchgear, transformers, sectionalizing terminating cable in applications where the visible open
cabinets and underground distribution vault and ground will be achieved through the use of an
applications. The Bolted T-body system is comprised of a internal switch and viewing window. In addition, it can be
standard 600 A T-body, an unthreaded compression lug, combined with other Bolted T-body kits and/or deadbreak
a cable adapter and a basic insulating plug with cap. junctions to construct a multi-way separable splice.
Bolted T-body
System
THREADED
STUD BASIC INSULATING
INSULATING PLUG
PLUG CAP
INTEGRAL T-BODY
BUSHING
UNTHREADED
COMPRESSION LUG
CABLE ADAPTER
6 2 5 B T
T = Test Point
Select Cable Adapter Code from Column 1 Blank = Without
Cable Adapter Cable Insulation Cable Insulation
Code Range (Inches) Range (mm)
E .530 - .680 13,5 - 17,3
F .640 - .820 16,3 - 20,8
Select Connector Code from Column 1 or 2
G .760 - .950 19,3 - 24,1
H .850 - 1.050 21,6 - 26,7 Shear Bolt
15 kV - 175mil 15 kV - 220mil 25 kV - 260mil 35 kV - 345mil
Connector Connector AWG or (Inches)
J .980 - 1.180 24,9 - 30,0 Code Code kcmil Stranding (Inches) (Inches) (Inches)
K 1.090 - 1.310 27,7 - 33,3 #2 Stranded & Compressed 0.635 - 0.730 0.725 - 0.825
22 #1 Compact & Solid 0.645 - 0.735 0.735 - 0.830
L 1.180 - 1.465 30,0 - 37,2 0.805 - 0.905
#1 Stranded & Compressed 0.675 - 0.770 0.765 - 0.855 0.835 - 0.935
LM 1.280 - 1.430 32,5 - 36,3 23 1/0 Compact & Solid 0.680 - 0.775 0.770 - 0.865 0.835 - 0.940 1.010 - 1.120
1/0 Stranded & Compressed 0.715 - 0.810 0.805 - 0.905 0.875 - 0.980 1.045 - 1.155
M 1.370 - 1.630 34,8 - 41,4 24 2/0 Compact & Solid 0.715 - 0.815 0.805 - 0.905 0.875 - 0.980 1.045 - 1.160
U1
N 1.515 - 1.780 38,5 - 45,2 25 2/0 Stranded & Compressed 0.760 - 0.855 0.850 - 0.950 0.920 - 1.025 1.090 - 1.200
3/0 Compact & Solid 0.765 - 0.860 0.855 - 0.955 0.925 - 1.030 1.095 - 1.205
P 1.725 - 1.935 43,8 - 49,1 3/0 Stranded & Compressed 0.810 - 0.905 0.900 - 1.000 0.970 - 1.075 1.140 - 1.255
26 4/0 Compact & Solid 0.815 - 0.910 0.905 - 1.005 0.975 - 1.080 1.925 - 1.260
27 4/0 Stranded & Compressed 0.865 - 0.965 0.955 - 1.060 1.025 - 1.135 1.195 - 1.310
250 0.880 - 0.965 1.010 - 1.115 1.025 - 1.135 1.210 - 1.315
Deadbreak Bolted Elbow Component Parts:
Compact & Solid
28 250 Stranded & Compressed 0.920 - 1.020 1.010 - 1.115 1.080 - 1.190 1.250 - 1.370
29 350 Compact 0.980 - 1.065 1.070 - 1.155 1.140 - 1.230 1.310 - 1.410
U2
Description Catalog # 30 350 Stranded & Compressed 1.025 - 1.130 1.115 - 1.220 1.185 - 1.295 1.355 - 1.475
T-Body with Test Point 625TBT 32 500 Compact 1.100 - 1.185 1.190 - 1.275 1.260 - 1.350 1.430 - 1.530
500 Stranded & Compressed 1.150 - 1.260 1.240 - 1.355 1.310 - 1.430 1.480 - 1.605
T-Body without Test Point 625TB
33 600 Compact 1.185 - 1.270 1.275 - 1.365 1.345 - 1.440 1.575 - 1.615
35 600 Stranded & Compressed 1.235 - 1.350 1.325 - 1.445 1.395 - 1.520 1.565 - 1.695
Aluminum Insulating Plug 625BIP 700 Compact 1.245 - 1.335 1.335 - 1.430 1.405 - 1.500 1.575 - 1.680
U3
with Cap 36 750 Compact 1.280 - 1.365 1.370 - 1.460 1.440 - 1.535 1.610 - 1.710
700 Stranded & Compressed 1.305 - 1.420 1.395 - 1.515 1.465 - 1.590 1.635 - 1.765
5/8” - 11 UNC Threaded 625SA 38 750 Stranded & Compressed 1.340 - 1.456 1.430 - 1.550 1.500 - 1.625 1.670 - 1.800
900 Compact 1.370 - 1.455 1.460 - 1.550 1.530 - 1.625 1.700 - 1.800
Aluminum Stud
39 800 Stranded & Compressed 1.370 - 1.455 1.460 - 1.580 1.530 - 1.655 1.700 - 1.835
Cable Adapter 625CAx 40 900 Stranded & Compressed 1.430 - 1.550 1.520 - 1.645 1.590 - 1.720 1.760 - 1.895
U4 1000 Compact 1.430 - 1.515 1.520 - 1.610 1.590 - 1.685 1.760 - 1.865
Compression Connector 625LUGxx 41 1000 Stranded & Compressed 1.485 - 1.610 1.575 - 1.705 1.645 - 1.775 1.815 - 1.955
The Hubbell Power Systems 600 A 15 kV or 25/28 kV The ETP system is ideal for applications where a 200 A tap
rated Deadbreak ETP (Elbow Tap Plug) Termination System is desired for test or ground purposes, with the visible open
is designed to terminate medium voltage underground achieved through use of an internal switch and a viewing
distribution cable to switchgear, transformers, window. The ETP is also ideal for adding a 200 A tap to an
sectionalizing cabinets and underground distribution existing 600 A elbow termination.
vault applications. The ETP system is comprised of a
standard 600 A T-body, an unthreaded compression lug, The 200 A loadbreak interface can be either 15 kV or 25/28 kV
a cable adapter and the ETP. The T-body can be ordered rated. This interface allows for live test, visible ground, addition
with or without a capacitive test point. of a 200 A tap, or installation of an elbow arrester to protect your
underground distribution system from voltage surges.
ETP
Elbow Termination System
THREADED
STUD ELBOW INSULATING CAP
TAP PLUG (OPTIONAL)
INTEGRAL
T-BODY
BUSHING
UNTHREADED
COMPRESSION LUG
CABLE ADAPTER
6 E T P
J = Seal Kit
S = Shield Adapter Kit
Blank = Neither
T = Test Point
Blank = Without
Select Cable Adapter Code from Column 1
Cable Adapter Cable Insulation Cable Insulation
Code Range (Inches) Range (mm)
Select Connector Code from Column 1 or 2
E .530 - .680 13,5 - 17,3
F .640 - .820 16,3 - 20,8 Shear Bolt
Connector Connector AWG or 15 kV - 175mil 15 kV - 220mil 25 kV - 260mil 35 kV - 345mil
G .760 - .950 19,3 - 24,1 Code kcmil Stranding (Inches) (Inches) (Inches) (Inches)
Code
H .850 - 1.050 21,6 - 26,7 #2 Stranded & Compressed 0.635 - 0.730 0.725 - 0.825
J .980 - 1.180 24,9 - 30,0 22 #1 Compact & Solid 0.645 - 0.735 0.735 - 0.830 0.805 - 0.905
K 1.090 - 1.310 27,7 - 33,3 #1 Stranded & Compressed 0.675 - 0.770 0.765 - 0.855 0.835 - 0.935
23 1/0 Compact & Solid 0.680 - 0.775 0.770 - 0.865 0.835 - 0.940 1.010 - 1.120
L 1.180 - 1.465 30,0 - 37,2 24 1/0 Stranded & Compressed 0.715 - 0.810 0.805 - 0.905 0.875 - 0.980 1.045 - 1.155
U1 2/0 Compact & Solid 0.715 - 0.815 0.805 - 0.905 0.875 - 0.980 1.045 - 1.160
LM 1.280 - 1.430 32,5 - 36,3 2/0 Stranded & Compressed 0.760 - 0.855 0.850 - 0.950 0.920 - 1.025 1.090 - 1.200
M 1.370 - 1.630 34,8 - 41,4 25 3/0 Compact & Solid 0.765 - 0.860 0.855 - 0.955 0.925 - 1.030 1.095 - 1.205
1.515 - 1.780 38,5 - 45,2 26 3/0 Stranded & Compressed 0.810 - 0.905 0.900 - 1.000 0.970 - 1.075 1.140 - 1.255
N 4/0 Compact & Solid 0.815 - 0.910 0.905 - 1.005 0.975 - 1.080 1.925 - 1.260
P 1.725 - 1.935 43,8 - 49,1 27 4/0 Stranded & Compressed 0.865 - 0.965 0.955 - 1.060 1.025 - 1.135 1.195 - 1.310
250 Compact & Solid 0.880 - 0.965 1.010 - 1.115 1.025 - 1.135 1.210 - 1.315
28 250 Stranded & Compressed 0.920 - 1.020 1.010 - 1.115 1.080 - 1.190 1.250 - 1.370
Deadbreak ETP Elbow Component Items: U2 29 350 Compact 0.980 - 1.065 1.070 - 1.155 1.140 - 1.230 1.310 - 1.410
30 350 Stranded & Compressed 1.025 - 1.130 1.115 - 1.220 1.185 - 1.295 1.355 - 1.475
Description Catalog # 32 500 Compact 1.100 - 1.185 1.190 - 1.275 1.260 - 1.350 1.430 - 1.530
500 Stranded & Compressed 1.150 - 1.260 1.240 - 1.355 1.310 - 1.430 1.480 - 1.605
T-Body with Test Point 625TBT 33 600 Compact 1.185 - 1.270 1.275 - 1.365 1.345 - 1.440 1.575 - 1.615
T-Body without Test Point 625TB 35 600 Stranded & Compressed 1.235 - 1.350 1.325 - 1.445 1.395 - 1.520 1.565 - 1.695
700 Compact 1.245 - 1.335 1.335 - 1.430 1.405 - 1.500 1.575 - 1.680
15 kV Elbow Tap Plug (ETP) 615ETP U3 36 750 Compact 1.280 - 1.365 1.370 - 1.460 1.440 - 1.535 1.610 - 1.710
700 Stranded & Compressed 1.305 - 1.420 1.395 - 1.515 1.465 - 1.590 1.635 - 1.765
25/28 kV Elbow Tap Plug (ETP) 625ETP 38 750 Stranded & Compressed 1.340 - 1.456 1.430 - 1.550 1.500 - 1.625 1.670 - 1.800
900 Compact 1.370 - 1.455 1.460 - 1.550 1.530 - 1.625 1.700 - 1.800
5/8” - 11 UNC Threaded 625SA 39 800 Stranded & Compressed 1.370 - 1.455 1.460 - 1.580 1.530 - 1.655 1.700 - 1.835
Aluminum Stud 900 Stranded & Compressed 1.430 - 1.550 1.520 - 1.645 1.590 - 1.720 1.760 - 1.895
U4 40 1000 Compact 1.430 - 1.515 1.520 - 1.610 1.590 - 1.685 1.760 - 1.865
15 kV Insulating Cap 215ICI 41 1000 Stranded & Compressed 1.485 - 1.610 1.645 - 1.775 1.815 - 1.955
1.575 - 1.705
25/28 kV Insulating Cap 9U01BEW500
Notes:
Cable Adapter 625CAx Connectors can be used for both aluminum and copper cable conductors.
Contact representative for conductors not listed above.
Compression Connector 625LUGxx
Shear Bolt Connector 625LUGUx
Cable Sizing Kit 625CKxxx
The Hubbell Power Systems 600 A 15 kV or 25/28 kV The LRTP system is ideal for applications where the
rated Deadbreak LRTP (Loadbreak Reducing Tap Plug) termination will be moved to achieve a visible break and
Termination System is designed to connect medium ground. The integral termination system, T-body and
voltage underground distribution cable to switchgear, LRTP as one unit, makes it easier to install and remove
transformers, sectionalizing cabinets and underground from the mating bushing interface.
distribution vault applications.
The LRTP system uses a threaded compression lug The 200 A loadbreak interface can be either 15 kV
allowing the LRTP to be threaded into the T-body or 25/28 kV rated. This interface allows for live test,
forming an integral termination system. The T-body phasing and visible ground. In addition, it can be used
can be ordered with or without a capacitive test point. to add a tap, or install an elbow arrester to protect your
underground distribution system from voltage surges.
LRTP
Elbow Termination System
INSULATING CAP
T-BODY LOADBREAK
(OPTIONAL)
REDUCING
INTEGRAL TAP PLUG
BUSHING
THREADED
COMPRESSION LUG
CABLE ADAPTER
6 L R T P
J = Seal Kit
S = Shield Adapter Kit
Blank = Neither
15 = 15 kV Voltage Class
25 = 25/28 kV Voltage Class C = 200 A Insulating Cap
Blank = Without
T = Test Point
Select Cable Adapter Code from Column 1 Blank = Without
Cable Adapter Cable Insulation Cable Insulation
Code Range (Inches) Range (mm)
Select Connector Code from Column 1
E .530 - .680 13,5 - 17,3
F .640 - .820 16,3 - 20,8 Connector AWG or 15 kV - 175mil 15 kV - 220mil 25 kV - 260mil 35 kV - 345mil
kcmil Stranding (Inches) (Inches) (Inches) (Inches)
G .760 - .950 19,3 - 24,1 Code
H .850 - 1.050 21,6 - 26,7 #2 Stranded & Compressed 0.635 - 0.730 0.725 - 0.825
22 #1 Compact & Solid 0.645 - 0.735 0.735 - 0.830 0.805 - 0.905
J .980 - 1.180 24,9 - 30,0 #1 Stranded & Compressed 0.675 - 0.770 0.765 - 0.855 0.835 - 0.935
K 1.090 - 1.310 27,7 - 33,3 23 1/0 Compact & Solid 0.680 - 0.775 0.770 - 0.865 0.835 - 0.940 1.010 - 1.120
L 1/0 Stranded & Compressed 0.715 - 0.810 0.805 - 0.905 0.875 - 0.980 1.045 - 1.155
1.180 - 1.465 30,0 - 37,2 24 2/0 Compact & Solid 0.715 - 0.815 0.805 - 0.905 0.875 - 0.980 1.045 - 1.160
LM 1.280 - 1.430 32,5 - 36,3 25 2/0 Stranded & Compressed 0.760 - 0.855 0.850 - 0.950 0.920 - 1.025 1.090 - 1.200
3/0 Compact & Solid 0.765 - 0.860 0.855 - 0.955 0.925 - 1.030 1.095 - 1.205
M 1.370 - 1.630 34,8 - 41,4 3/0 Stranded & Compressed 0.810 - 0.905 0.900 - 1.000 0.970 - 1.075 1.140 - 1.255
26 4/0 0.815 - 0.910 0.905 - 1.005 0.975 - 1.080 1.925 - 1.260
N 1.515 - 1.780 38,5 - 45,2 Compact & Solid
27 4/0 Stranded & Compressed 0.865 - 0.965 0.955 - 1.060 1.025 - 1.135 1.195 - 1.310
P 1.725 - 1.935 43,8 - 49,1 250 Compact & Solid 0.880 - 0.965 1.010 - 1.115 1.025 - 1.135 1.210 - 1.315
28 250 Stranded & Compressed 0.920 - 1.020 1.010 - 1.115 1.080 - 1.190 1.250 - 1.370
29 350 Compact 0.980 - 1.065 1.070 - 1.155 1.140 - 1.230 1.310 - 1.410
Deadbreak LRTP Component Items: 30 350 Stranded & Compressed 1.025 - 1.130 1.115 - 1.220 1.185 - 1.295 1.355 - 1.475
32 500 Compact 1.100 - 1.185 1.190 - 1.275 1.260 - 1.350 1.430 - 1.530
500 Stranded & Compressed 1.150 - 1.260 1.240 - 1.355 1.310 - 1.430 1.480 - 1.605
Description Catalog # 33 600 Compact 1.185 - 1.270 1.275 - 1.365 1.345 - 1.440 1.575 - 1.615
T-Body with Test Point 625TBT 35 600 Stranded & Compressed 1.235 - 1.350 1.325 - 1.445 1.395 - 1.520 1.565 - 1.695
700 Compact 1.245 - 1.335 1.335 - 1.430 1.405 - 1.500 1.575 - 1.680
T-Body without Test Point 625TB 36 750 Compact 1.280 - 1.365 1.370 - 1.460 1.440 - 1.535 1.610 - 1.710
700 Stranded & Compressed 1.305 - 1.420 1.395 - 1.515 1.465 - 1.590 1.635 - 1.765
15 kV Loadbreak Reducing Tap 615LRTP 38 750 Stranded & Compressed 1.340 - 1.456 1.430 - 1.550 1.500 - 1.625 1.670 - 1.800
Plug (LRTP) 900 Compact 1.370 - 1.455 1.460 - 1.550 1.530 - 1.625 1.700 - 1.800
39 800 Stranded & Compressed 1.370 - 1.455 1.460 - 1.580 1.530 - 1.655 1.700 - 1.835
25/28 kV Loadbreak Reducing Tap 625LRTP 900 Stranded & Compressed 1.430 - 1.550 1.520 - 1.645 1.590 - 1.720 1.760 - 1.895
Plug (LRTP) 40 1000 Compact 1.430 - 1.515 1.520 - 1.610 1.590 - 1.685 1.760 - 1.865
41 1000 Stranded & Compressed 1.485 - 1.610 1.575 - 1.705 1.645 - 1.775 1.815 - 1.955
15 kV Insulating Cap 215ICI
Notes:
25/28 kV Insulating Cap 9U01BEW500 Connectors can be used for both aluminum and copper cable conductors.
Cable Adapter 625CAx Contact representative for conductors not listed above.
6 2 5 L
T = Test Point
Blank = Without
The Hubbell 600 A Deadbreak T-body can also be used The basic Catalog Number will be 625L_. By inserting
to splice power cables by connecting multiple T-bodies the splice code, “2” immediately following the “L” in
using other accessory products. the basic catalog number, the catalog number to order
is a 625L2. All “non-size” sensitive components will be
To order a Modular Splicing Kit, simply build your included in the kit when ordering. You must order “size
catalog number using the indicator above. sensitive” components separately.
Compression connectors can be used for both aluminum
To order Hubbell Modular Splicing kits you must first and copper cable conductors.
specify the splicing application by selecting the Splicing
Code that represents your application.
625CP
Connecting Plug
The Connecting Plug is exclusively for joining or connecting
two or more 600 A T-bodies or bushing extenders. The
Connecting Plug incorporates a straight through aluminum
bus for the transfer of current between the mating 600 A
T-bodies. To tighten, a 3/8” hex wrench is inserted into
broached holes in each end of bus bar.
625BIP
Basic Insulating Plug
The Basic Insulating Plug is a key component of every Hubbell
600 A Deadbreak T-body Kit and is required to secure the 600 A T-body
in place. The 1” hex located on top of the Basic Insulating Plug doubles
as a means of tightening the T-body on to its mating part and also as a
capacitive test point.
625IC
Insulating Cap
625ICSP
Short Insulating Cap
The Short Insulating Cap provides the same function as the standard
625IC but utilizes less space. The stud is also permanently installed.
625BE
Bushing Extender
9_ _BA
Bushing Adapter
9 B A
15 = 15 kV Voltage Class
25 = 25/28 kV Voltage Class
625SB
Standoff Bushing
The 25/28 kV Standoff Bushing provides a single deadbreak
interface used to isolate and sectionalize an energized cable.
The Standoff Bushing is designed to be installed in the
parking stand mounted on a transformer or other device. A
grounding lug is provided on the bracket for attachment of
a ground wire.
625GB
Grounded Bushing
The 25/28 kV Grounded Bushing provides a single
deadbreak interface used to achieve a visible ground on
de-energized cables.
Deadbreak Components:
625SK52 Cold Shrink Cable Seal Kit for JCN cable
with an overall diameter of 0.97” to 1.95”
625SK53 Cold Shrink Cable Seal Kit for JCN cable
with an overall diameter of 1.25” to 2.65”
625SK60 Tape Shield Adapter Kit for cable with an
overall diameter of 0.83” to 1.95”
625SK61 Tape Shield Adapter Kit for cable with an
overall diameter of 1.25” to 2.65”
625SK62 Tape Shield Adapter Kit for cable with an
overall diameter of 1.63” to 2.67”
6_ _ ETP
Elbow Tap Plug
The 600 A Elbow Tap Plug is designed to add a 200 A loadbreak
interface to an existing 600 A deadbreak T-Body. It is ideal for
retrofitting an existing bolted elbow with a 200 A tap or for new
applications. A common application is for testing and grounding 600
A systems. The ETP is fault close rated to 10,000 A, complies with IEEE
Std. 386 and is available in both 15 kV and 25/28 kV ratings.
6 E T P
15 = 15 kV Voltage Class
25 = 25/28 kV Voltage Class
6_ _ LRTP
Loadbreak Reducing Tap Plug
6 L R T P
15 = 15 kV Voltage Class
25 = 25/28 kV Voltage Class
625LUG_ _
Compression/Shear Bolt Connectors
Shear Bolt Connector Concentric
Connector Contact Solid
6 2 5 L U G Code Code Compressed
22 #2 #1
23 #1 1/0
24 1/0 2/0
U1
25 2/0 3/0
26 3/0 4/0
27 4/0 250
28 250 300
29 300 350
U2 30 350 400
31 400 450
32 450 500/550
33 500 600
34 550 650
U3 35 600 700
36 650 750
38 700/750 900
39 800 ---
*Connectors can be used for both aluminum and
40 900 1000
copper cable conductors. U4
41 1000 ---
44 1250 ---
6 2 5 J
2 = 2 Position
3 = 3 Position
4 = 4 Position
B = With Bracket
U = With U-straps
JUNCTION DESCRIPTION
Hubbell junctions sectionalize feeders or provide a Junctions are available with a stainless steel mounting
lateral tap. They are available in two, three and four bracket which includes two integral parking stands and
point configurations. a ground lug. Junctions can also be ordered with only
U-straps for surface mounting.
Standard 600 A products contain an aluminum bus
bar and mate with any 15/25/28 kV rated separable
connector.
The 25/28 kV TapMaster™ Junction offers a complete change in design approach, addressing the issues of space
savings in vaults and enclosures, mounting flexibility and the flexibility of locating parking stands to accept accessory
products required to operate and maintain a distribution system.
3, 4, 5, or 6 pt junction with any configuration of 600 A interfaces and 200 A wells needed for any project.
6 2 8 T M
15 kV Loadbreak
Reducing Tap Plug
615LRTP
15 kV Insulating Cap
215ICx 600A Deadbreak
25 kV Bushing Extender Junction W/U-Strap
625BE 625JxU
25 kV Integral
Bushing
PRODUCTION TESTS
100% factory test for partial discharge and either AC HI-POT
(50 kV for 60 seconds) or impulse (BIL) (150 kV 1.2 x 50 μsec. wave).
The Hubbell Power Systems 600 A 35 kV rated a basic insulating plug with cap. The T-body can be
Deadbreak Bolted T-body System is designed to ordered with or without a capacitive test point.
terminate medium voltage underground distribution Bolted T-body systems provide an economical means of
cable to switchgear, transformers, sectionalizing terminating cable in applications where the visible open
cabinets and underground distribution vault and ground will be achieved through the use of an
applications. The Bolted T-body system is comprised of a internal switch and viewing window. In addition, it can be
standard 600 A T-body, an unthreaded compression lug, combined with other Bolted T-body kits and/or deadbreak
a cable adapter and junctions to construct a multi-way separable splice.
Bolted T-body
System
THREADED
STUD BASIC INSULATING
INSULATING PLUG
PLUG CAP
INTEGRAL T-BODY
BUSHING
UNTHREADED
COMPRESSION LUG
CABLE ADAPTER
6 3 5 B T
T = Test Point
Select Cable Adapter Code from Column 1 Blank = Without
Cable Adapter Cable Insulation Cable Insulation
Code Range (Inches) Range (mm)
D .750 - .985 19.05 - 25.0
Select Connector Code from Column 1 or 2
E 0.930 - 1.040 23.6 - 26.4
Shear Bolt Connector AWG 25 kV - 35 kV - 35 kV -
F 980 - 1.115 24.9 - 28.3 Connector or Stranding 260mil 345mil 420mil
Code Code kcmil (Inches) (Inches) (Inches)
G 1.040 - 1.175 26.4 - 29.8
H 1.095 - 1.240 27.8 - 31.5 22 #1 Comp & Sol 0.805 - 0.905
The Hubbell Power Systems 600 A 35 kV rated Deadbreak The ETP system is ideal for applications where a 200 A
ETP (Elbow Tap Plug) Termination System is designed to tap is desired for test or ground purposes, with the
terminate medium voltage underground distribution visible open achieved through use of an internal switch
cable to switchgear, transformers, sectionalizing cabinets and a viewing window. The ETP is also ideal for adding a
and underground distribution vault applications. The 200 A tap to an existing 600 A elbow termination.
ETP system is comprised of a standard 600 A T-body, an
unthreaded compression lug, a cable adapter and the The 200 A loadbreak interface can be either 35 kV rated.
ETP. The T-body can be ordered with or without a capaci- This interface allows for live test, visible ground, addition
tive test point. of a 200 A tap, or installation of an elbow arrester to protect
your underground distribution system from voltage surges.
ETP
Elbow Termination System
THREADED
STUD ELBOW INSULATING CAP
TAP PLUG (OPTIONAL)
INTEGRAL
T-BODY
BUSHING
UNTHREADED
COMPRESSION LUG
CABLE ADAPTER
6 3 5 E T P
J = Seal Kit
Hubbell Product Prefix S = Shield Adapter Kit
Blank = Neither
T = Test Point
Blank = Without
Select Cable Adapter Code from Column 1
Cable Adapter Cable Insulation Cable Insulation
Code Range (Inches) Range (mm)
Select Connector Code from Column 1 or 2
D .750 - .985 19.05 - 25.0
Shear Bolt Connector AWG 25 kV - 35 kV - 35 kV -
E 0.930 - 1.040 23.6 - 26.4 Connector or Stranding 260mil 345mil 420mil
Code Code kcmil (Inches) (Inches) (Inches)
F 980 - 1.115 24.9 - 28.3
G 1.040 - 1.175 26.4 - 29.8 22 #1 Comp & Sol 0.805 - 0.905
635BIP
Basic Insulating Plug
The Basic Insulating Plug is a key component of every Hubbell
600 A Deadbreak T-body Kit and is required to secure the 600 A T-body
in place. The 1” hex located on top of the Basic Insulating Plug doubles
as a means of tightening the T-body on to its mating part and also as a
capacitive test point.
635IC
Insulating Cap
635BE
Bushing Extender
Deadbreak Components:
625SK52 Cold Shrink Cable Seal Kit for JCN cable
with an overall diameter of 0.97” to 1.94”
625SK53 Cold Shrink Cable Seal Kit for JCN cable
with an overall diameter of 1.25” to 2.65”
22 #2 #1
23 #1 1/0
24 1/0 2/0
U1
25 2/0 3/0
26 3/0 4/0
27 4/0 250
28 250 300
29 300 350
U2 30 350 400
31 400 450
32 450 500/550
33 500 600
34 550 650
U3 35 600 700
36 650 750
38 700/750 900
39 800 ---
*Connectors can be used for both aluminum and
copper cable conductors. 40 900 1000
U4
41 1000 ---
44 1250 ---
C7 Page 56 | July 2019
35 KV DEADBREAK JUNCTIONS
JUNCTION SELECTION AND ORDERING
6 3 5 J
2 = 2 Position
3 = 3 Position
4 = 4 Position
B = With Bracket
U = With U-straps
JUNCTION DESCRIPTION
Hubbell junctions sectionalize feeders or provide a Junctions are available with a stainless steel mounting
lateral tap. They are available in two, three and four bracket which includes two integral parking stands and
point configurations. a ground lug. Junctions can also be ordered with only
U-straps for surface mounting.
Standard 600 A products contain an aluminum bus bar
and mate with any 35 kV rated separable connector.
60 Hz Temporary Overvoltage Capability with Prior Duty Hubbell arresters are fully shielded and submersible,
(60° C Ambient) either continuously or intermittently, to a depth of 6
feet (2m).
Installation:
Voltage Per Unit MCOV
Performance Characteristics:
Tests were performed in accordance with applicable
sections of IEEE Std. 386 (Separable Insulated
Connector Systems for Power Distribution Systems
Above 600 V) and IEEE Std. C62.11 (Metal Oxide Surge
Arresters for Alternating Current Power Circuits) with
Time Duration - Seconds
test levels chosen that represent typical underground
distribution systems.
COMMON TERMS:
Discharge Voltage: The voltage the arrester
develops while discharging a surge to ground. The
lower the voltage, the better the protection
PRODUCT FEATURES:
Pulling Eye provides positive hotstick operation.
The pulling eye strength exceeds 500 lbs of force.
Protective Characteristics
Fiberglass Wrap ensures that the MOV block stack remains in one piece and
prevents the blocks from breaching the side wall should the arrester fail.
ID Band provides clear visual identification of arrester MCOV and duty cycle
ratings.
Flexible Lead is #4 AWG copper rope lay conductor 595 strand (7 x 85).
Ends are soldered to prevent fraying. Standard length is 36” long.
Other lead lengths are available.
MOV Blocks are the same as used in Ohio Brass overhead arresters.
Protective Characteristics
Catalog MCOV Rating 0.5 µsec. 5 kA Maximum Discharge Voltage (kV Crest)
Number kV kV Max IR-kV 8x20 µsec. Current Wave
1.5 kA 3.0 kA 5.0 kA 10 kA 20 kA
215_LA03 2.55 3 12.5 9.8 10.3 11 12.3 14.3
215_LA06 5.1 6 25 19.5 20.5 22 24.5 28.5
215_LA09 7.65 9 33.5 26 28 30 33 39
215_LA10 8.4 10 36 27 29.5 31.5 36 41.5
215_LA12 10.2 12 50 39 41 44 49 57
215_LA15 12.7 15 58.5 45.5 48.5 52.0 57.5 67.5
215_LA18 15.3 18 67.0 52.0 56.0 60.0 66.0 78.0
For ungrounded or impedance-grounded systems, the MCOV should be at least 90 percent of maximum
phase-to-phase voltage. If you need assistance with arrester selection, please contact your Hubbell Power
Systems account representative for details.
Example: Elbow arrester for use on a grounded 13.8 kV L-L system is: 215ELA10
2 1 5 L A
E = Elbow Arrester
P = Parkingstand
215PLA03 2.55 3
215PLA06 5.1 6
15 kV Class
215PLA09 Interface 5 7.65 9 4.6 (2.09)
215PLA10 8.4 10 215PLA _ _
215PLA12 10.2 12
Fiberglass Wrap ensures that the MOV block stack remains in one piece and
prevents the blocks from breaching the side wall should the arrester fail.
ID Band provides clear visual identification of arrester MCOV and duty cycle
ratings.
Flexible Lead is #4 AWG copper rope lay conductor 595 strand (7 x 85).
Ends are soldered to prevent fraying. Standard length is 36” long.
Other lead lengths are available.
MOV Blocks are the same as used in Ohio Brass overhead arresters.
Protective Characteristics
Catalog MCOV Rating 0.5 µsec 5 kA Maximum Discharge Voltage (kV Crest)
Number kV kV Max IR-kV 8x20 µsec. Current Wave
1.5 kA 3.0 kA 5.0 kA 10 kA 20 kA
225_LA09 7.65 9 33.5 26 28 30 33 39
225_LA10 8.4 10 36 27 29.5 31.5 36 41.5
225_LA12 10.2 12 50 39 41 44 49 57
225_LA15 12.7 15 58.5 45.5 48.5 52 57.5 67.5
225_LA18 15.3 18 67.0 52 56 60 66 78
225_LA21 17.0 21 73 55 60 64 73 84
For ungrounded or impedance-grounded systems, the MCOV should be at least 90 percent of maximum
phase-to-phase voltage. If you need assistance with arrester selection, please contact your Hubbell Power
Systems account representative for details.
Example: Elbow arrester for use on a grounded 23.0 kV L-L system is: 225ELA18
2 2 5 L A
Catalog IEEE Std. 386 MCOV Rated Dimensions Inch (mm) Weight
Number Interface (kV) Voltage (kV) A B C Lbs (kg)
225ELA09 7.65 9
6.6
225ELA10 8.4 10 3.7 1.7
(168)
225ELA12 25/28 kV Class 10.2 12 7.9 3.1
225ELA15 Interface 7A 12.7 15 (201) (79)
10.2 5.2 2.4
225ELA18 15.3 18
(259) 10.2"(259)
225ELA21 17 21
225PLA09 7.65 9
225PLA10 8.4 10
225PLA12 25/28 kV Class 10.2 12 4.6 2.09
225PLA15 Interface 7A 12.7 15
225PLA18 15.3 18 225PLA _ _
225PLA21 17 21
Fiberglass Wrap ensures that the MOV block stack remains in one piece and prevents the blocks
from breaching the side wall should the arrester fail.
ID Band provides clear visual identification of arrester MCOV and duty cycle ratings.
Flexible Lead is #4 AWG copper rope lay conductor 595 strand (7 x 85).
Ends are soldered to prevent fraying. Standard length is 36” long.
Other lead lengths are available.
MOV Blocks are the same as used in Ohio Brass overhead arresters.
Protective Characteristics
Catalog MCOV Rating 0.5 µsec. 5 kA Maximum Discharge Voltage (kV Crest)
Number kV kV Max IR-kV 8x20 µsec. Current Wave
1.5 kA 3.0 kA 5.0 kA 10 kA 20 kA
235ELA24 19.5 24 92.0 71.5 76.5 82.0 90.5 106.5
235ELA27 22.0 27 100.5 78.0 84.0 90.0 99.0 117.0
235ELA30 24.4 30 108.0 81.0 88.5 94.5 108.0 124.5
For ungrounded or impedance-grounded systems, the MCOV should be at least 90 percent of maximum
phase-to-phase voltage. If you need assistance with arrester selection, please contact your Hubbell Power
Systems account representative for details.
2 3 5 E L A
235ELA_ _
235ELA _ _
Caution
This product is only compatible with a 35 kV small interface, Interface 7B of IEEE Std.
386. It is not compatible with a 35 kV large interface, Interface 8 of IEEE Std. 386.
Fiberglass Wrap ensures that the MOV block stack remains in one piece and prevents the blocks
from breaching the side wall should the arrester fail.
ID Band provides clear visual identification of arrester MCOV and duty cycle ratings.
Flexible Lead is #4 AWG copper rope lay conductor 595 strand (7 x 85).
Ends are soldered to prevent fraying. Standard length is 36” long.
Other lead lengths are available.
MOV Blocks are the same as used in Ohio Brass overhead arresters.
Protective Characteristics
Catalog MCOV Rating 0.5 µsec. 5 kA Maximum Discharge Voltage (kV Crest)
Number kV kV Max IR-kV 8x20 µsec. Current Wave
1.5 kA 3.0 kA 5.0 kA 10 kA 20 kA 40kA
236ELA27 22.0 27 88 70.8 75.4 80.4 90.5 104.6 130.7
236ELA30 24.4 30 97.8 78.7 83.8 89.3 100.6 116.2 145.2
236ELA33 26.9 33 107.6 86.6 92.2 98.3 110.7 127.9 159.8
236ELA36 29 36 117.4 94.4 100.5 107.2 120.7 139.4 174.3
For ungrounded or impedance-grounded systems, the MCOV should be at least 90 percent of maximum
phase-to-phase voltage. If you need assistance with arrester selection, please contact your Hubbell Power
Systems account representative for details.
2 3 6 E L A
16
236ELA_ _
235ELA _ _
236ELA24 19.5 24
236ELA27 22 27
35 kV Class 9.2 13.9 4.0
236ELA30 24.4 30 6.5 2.9
Interface 9 (233 ) (353) (101)
236ELA33 27 33
236ELA36 29 36
Caution
This product is only compatible with a 35 kV large interface, Interface 8 of IEEE Std.
386. It is not compatible with a 35 kV small interface, Interface 7B of IEEE Std. 386.
AEIC/ICEA Cable Std. Concentric Stranded Compressed Stranded Compact Stranded Solid
Insulation
AWG or Voltage Min Dia. Max Dia. Min Dia. Max Dia. Min Dia. Max Dia. Min Dia. Max Dia.
Wall
kcmil Class (kV) (inches) (inches) (inches) (inches) (inches) (inches) (inches) (inches)
Thickness
.175 15 0.645 0.730 0.635 0.720 0.620 0.705 0.610 0.695
.220 15 0.735 0.825 0.725 0.815 0.710 0.800 0.700 0.790
#2
.260 25 --- --- --- --- --- --- --- ---
.345 35 --- --- --- --- --- --- --- ---
.175 15 0.685 0.770 0.675 0.760 0.655 0.735 0.645 0.725
.220 15 0.775 0.865 0.765 0.855 0.745 0.830 0.735 0.820
#1
.260 25 0.845 0.935 0.835 0.925 0.815 0.905 0.805 0.895
.345 35 --- --- --- --- --- --- --- ---
.175 15 0.725 0.810 0.715 0.800 0.690 0.775 0.680 0.760
.220 15 0.815 0.905 0.805 0.895 0.780 0.865 0.770 0.855
1/0
.260 25 0.885 0.980 0.875 0.965 0.850 0.940 0.835 0.925
.345 35 1.055 1.155 1.045 1.145 1.020 1.120 1.010 1.110
.175 15 0.775 0.855 0.760 0.845 0.730 0.815 0.715 0.800
.220 15 0.865 0.950 0.850 0.935 0.820 0.905 0.805 0.895
2/0
.260 25 0.935 1.025 0.920 1.010 0.890 0.980 0.875 0.965
.345 35 1.105 1.200 1.090 1.190 1.060 1.160 1.045 1.145
.175 15 0.825 0.905 0.810 0.895 0.775 0.860 0.765 0.845
.220 15 0.915 1.000 0.900 0.985 0.865 0.955 0.855 0.940
3/0
.260 25 0.985 1.075 0.970 1.060 0.935 1.030 0.925 1.015
.345 35 1.155 1.255 1.140 1.240 1.105 1.205 1.095 1.195
.175 15 0.880 0.965 0.865 0.950 0.830 0.910 0.815 0.895
.220 15 0.970 1.060 0.955 1.045 0.920 1.005 0.905 0.990
4/0
.260 25 1.040 1.135 1.025 1.115 0.990 1.080 0.975 1.065
.345 35 1.210 1.310 1.195 1.295 1.160 1.260 1.145 1.245
.175 15 0.935 1.020 0.920 1.005 0.880 0.965
.220 15 1.025 1.115 1.010 1.100 0.970 1.060
250 --- ---
.260 25 1.095 1.190 1.080 1.175 1.040 1.135
.345 35 1.265 1.370 1.250 1.350 1.210 1.315
.175 15 1.045 1.130 1.025 1.110 0.980 1.065
.220 15 1.135 1.220 1.115 1.200 1.070 1.155
350 --- ---
.260 25 1.205 1.295 1.185 1.275 1.140 1.230
.345 35 1.375 1.475 1.355 1.455 1.310 1.410
.175 15 1.175 1.260 1.150 1.235 1.100 1.185
.220 15 1.265 1.355 1.240 1.330 1.190 1.275
500 --- ---
.260 25 1.335 1.430 1.310 1.405 1.260 1.350
.345 35 1.505 1.605 1.480 1.580 1.430 1.530
AEIC/ICEA Cable Std. Concentric Stranded Compressed Stranded Compact Stranded Solid
AWG or Insulation
Wall Voltage Min Dia. Max Dia. Min Dia. Max Dia. Min Dia. Max Dia. Min Dia. Max Dia.
kcmil Thickness Class (kV) (inches) (inches) (inches) (inches) (inches) (inches) (inches) (inches)
.175 15 1.265 1.350 1.235 1.325 1.185 1.270
.220 15 1.355 1.445 1.325 1.415 1.275 1.365
600 --- ---
.260 25 1.425 1.520 1.395 1.490 1.345 1.440
.345 35 1.595 1.695 1.565 1.670 1.515 1.615
.175 15 1.335 1.420 1.305 1.390 1.245 1.335
Never Compromise TM
www.hubbellpowersystems.com
Printed in USA