Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 29 views

    Ejercicios Exam Part B

    Uploaded by

    Edgargar
    The document contains 13 multiple choice questions that are part of a CWI exam. The questions cover topics like weld inspection acceptance criteria, weld defect evaluation, procedure qualification requirements, and interpreting procedure qualification test results.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Ejercicios Exam Part B

    Uploaded by

    Edgargar
    29 views3 pages
    The document contains 13 multiple choice questions that are part of a CWI exam. The questions cover topics like weld inspection acceptance criteria, weld defect evaluation, procedure qualification requirements, and interpreting procedure qualification test results.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document contains 13 multiple choice questions that are part of a CWI exam. The questions cover topics like weld inspection acceptance criteria, weld defect evaluation, procedure qualification requirements, and interpreting procedure qualification test results.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    29 views3 pages

    Ejercicios Exam Part B

    Uploaded by

    Edgargar
    The document contains 13 multiple choice questions that are part of a CWI exam. The questions cover topics like weld inspection acceptance criteria, weld defect evaluation, procedure qualification requirements, and interpreting procedure qualification test results.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    CWI EXAM PART B

    1. You are a Certified Welding Inspector. You are observing a weld being made. After examining
    the weld you notice a small star crack. What is the correct decision to be made after your finding?
    a. cracks are acceptable if they are not too long.
    b. Have the welder cut there heat up and burn it out on the next pass
    c. Nothing is required continue to weld and check out the next pass
    d. Grind down past the crack, reweld and check to see if the crack has been fixed.
    e. Use a qualified repair procedure for the process.

    2. It's your first day on a pipe fabrication job at a power plant, and they are installing
    large pipe. You are called to do a visual examination of a weld for sign off. You notice
    that a portion of the root pass reinforcement exceeds 3/16". What is the correct process
    for inspection?

    a. You want to get along with the personnel and sign off the weld.
    b. The reinforcement is over the acceptance criteria and is not ok to sign off.
    c. The reinforcement is not over the acceptance criteria and is not ok to sign off
    d. The fit-up had a high low not over the requirements and it is ok to sign off.
    e. If the weld looks good and is uniformed and no defects it is ok to sign off.

    3. What is the correct Visual Inspection Acceptance Criteria time for inspection for
    ASTM A 709 Grade 100 and 100W?

    a. Visual Inspection performed not less than 48 hours after completion


    b. Inspections of welds can begin immediately after welds has been completed.
    c. Inspections of welds can begin after welds have cooled to ambient temperature
    d. b and c above
    e. None of the above

    4. A weld metal analysis report shows the following values:


    C-0.07, Cr-0.50, Mo-0.50, Ni-0.75, Mn-1.75, Si-0.95
    What is the correct A-number?

    a. 1
    b. 3
    c. 6
    d. 8
    e. 10

    5. When examining guided bend specimens, one specimen has Porosity (P) pore that
    exceeds 1/8". There are no other discontinuities. The specimen is:

    a. acceptable
    b. unacceptable
    c. not enough information
    d. acceptable if none are on the edge
    e. none of the above

    6. A Groove weld procedure qualification test coupon has a single pass 1/2" fillet weld. If
    all required tests are passed, the procedure will be qualified for which of the following?

    a. Unlimited plate thickness for fillet welds only


    b. 1/2" single pass fillet weld and larger
    c. Minimum 3/16" Maximum 2T
    d. 1/2" single or multiple pass fillet welds of any size
    e. a and c above

    7. As a CWI, you are asked to verify the schedule of a piece of 6" diameter, schedule 80
    pipe. What is the O.D. and thickness supposed to be?

    a. 6.000 OD and .432" thick


    b. 6.625 OD and .280" thick
    c. 6.000 OD and .280" thick
    d. 6.625 OD and .432" thick
    e. none of the above

    8. What is the required Minimum Tensile/Yield Strength of ASTM A709 Grade 100 and
    100W Type E Plate? The thickness is less than 2 1/2".

    a. 100/90
    b. 105/90
    c. 110/100
    d. 115/100
    e. none of the above

    9. What is the F-No for AWS Specification A5.1 AWS Classification EXX48?

    a. 5
    b. 4
    c. 3
    d. 2
    e. none of the above

    10. A welding procedure is being qualified using ASTM A709 Grade 100W Type E
    Plate. The thickness is 1-1/2" and the welding is done in the 2G welding position using
    SMAW process. Assume all requirements are successfully met.
    For what minimum thickness ranges will this qualification be valid?
    a. unlimited thickness
    b. 3/16" minimum
    c. 1/8" to unlimited
    d. 3/16" to 2T
    e. none of the above

    11. A welding procedure is being qualified using ASTM A709 Grade 100W Type E
    Plate. The thickness is 1-1/2" and the welding is done in the 2G welding position using
    SMAW process. Assume all requirements are successfully met.
    Which of the following is matching UNS Numbers for this qualification?

    a. K41583
    b. K11856
    c. K21604
    d. all of the above
    e. none of the above

    12. A welding procedure is being qualified using ASTM A709 Grade 100W Type E
    Plate. The thickness is 1-1/2" and the welding is done in the 2G welding position using
    SMAW process. Assume all requirements are successfully met.
    For what ranges of diameters will this qualification be valid?

    a. up to 4" diameters
    b. 4" to 10" diameters only
    c. 8" Maximum
    d. all diameters
    e. there are no diameter provisions for this qualification

    13. A welding procedure is being qualified using ASTM A709 Grade 100W Type E
    Plate. The thickness is 1-1/2" and the welding is done in the 2G welding position using
    SMAW process. Assume all requirements are successfully met.
    For which of the following welding positions would the individual who welded this
    qualification be qualified?

    a. Plate 2G, F, H
    b. Plate and Pipe F, H
    c. Plate 3G, 4G, F, H
    d. Plate and Pipe 3G, 4G, F, H
    e. a and b above

    You might also like