 VN460SP

SINGLE CHANNEL HIGH SIDE SMART

SOLID STATE RELAY
T YPE V de ma g R DS(o n) IO UT V CC
VN460SP V CC -55V 20 m Ω 25 A 36 V

■ OUTPUT CURRENT (CONTINUOUS):

25 A @ TC = 25 o C
( s )
ct
■ 5 V LOGIC LEVEL COMPATIBLE INPUT 10
■

■
UNDER VOLTAGE SHUT-DOWN
OVER VOLTAGE SHUT-DOWN
d1u
■ THERMAL SHUT-DOWN
r o
Power SO-10 TM
■

■
OPEN DRAIN DIAGNOSTIC OUTPUT
VERY LOW STAND-BY POWER
e P
DISSIPATION

l e t
DESCRIPTION
The VN460SP is a monolithic device made using
s o
SGS-THOMSON Vertical Intelligent Power
Technology, intended for driving resistive or
O b
inductive loads with one side connected to
ground.
( s)- The control input is 5V CMOS logic level
compatible.

t
Built-in thermal shut-down protects the chip from
c
The open drain diagnostic output indicates open

u
over temperature and short circuit.

d
circuit (no load) and overtemperature status.

BLOCK DIAGRAM
r o
e P
l e t
s o
O b

September 2013 DocID5691 Rev 3 1/9

 VN460SP

ABSOLUTE MAXIMUM RATING

Symb ol Parameter Value Unit
VCC Power Supply Voltage (continuous) 45 V
-V CC Reverse Supply Voltage (continuous) -0.3 V
I OUT Output Current (continuous) Internally Limited A
IR Reverse Output Current -25 A
I IN Input Current ±10 mA
I STAT Status Pin Current ±10 mA
-I GND Reverse Ground Current -200 mA
V ESD Electrostatic Discharge (1.5 kΩ, 100 pF) 2000 V
P tot
o
Power Dissipation at T c ≤ 25 C 112

( s
W
o)
ct
Tj Junction Operating Temperature -40 to 150 C
o
T s tg Storage Temperature -55 to 150 C

d u
CONNECTION DIAGRAM
r o
e P
l e t
so
O b
) -
c t (s
d u
r o
e P
l e t
o
CURRENT AND VOLTAGE CONVENTIONS
s
O b

2/9
 VN460SP

ELECTRICAL TRANSIENTS REQUIREMENTS

ISO T/R T EST LEVEL S
7637/1
Test Pu lse
I II III IV Delays an d
Impedance
1 -25 V -50 V -75 V -100 V 2 ms, 10 Ω
2 +25 V +50 V +75 V +100 V 0.2 ms, 10 Ω
3a -25 V -50 V -100 V -150 V 0.1 µs, 50 Ω
3b +25 V +50 V +75 V +100 V 0.1 µs, 50 Ω
4 -4 V -5 V -6 V -7 V 100 ms, 0.01 Ω
5 +26.5 +46.5 +66.5 +86.5

( s )
400 ms, 2 Ω

u ct
ISO T/R TEST L EVELS RESUL TS
o d
7637/1
Test Pu lse
I II III
P r IV

e
let
1 C C C C
2 C C C C
3a C C
s o C C
3b C C
b C C

-O
4 C C C C

(s)
5 C E E E
(With a series resistor ≥ 1 KΩ in input and status pins).

c t
u
od
CL ASS CONT ENT S

C
P r
All function of the device are performed as designed after exposure to disturbance.
E

e t eOne or more functions of the device is not performed as designed after exposure and
cannot be returned to proper operation without replacing the device.

o l
b s
O

3/9
 VN460SP

THERMAL DATA
o
R t hj-ca se Thermal Resistance Junction-case Max 1.1 C/W
o
R thj-a (∗) Thermal Resistance Junction-ambient Max 50 C/W
(∗) When mounted using minimum recommended pad size on FR-4 board.

ELECTRICAL CHARACTERISTICS (VCC = 13 V; -40 oC < TJ < 125 oC unless otherwise specified)
POWER
Symb ol Parameter Test Cond ition s Min. Typ . Max. Un it
VCC Operating Supply 5.5 13 36 V
Voltage
V usd Under Voltage Shut 3 4 5.5

( s ) V

ct
Down
V ov Overvoltage Shut Down 36 39 45 V
R on On State Resistance I OUT = 5 A T J = 25 C
o

d u 20 mΩ
I OUT = 5 A
o
r o 36 mΩ
µA
IS Supply Current Off state
On State
TCase = 25 C

e P 15
1.4
30
3.3 mA

LOGIC INPUT
l e t
o
bs
Symb ol Parameter Test Cond ition s Min. Typ . Max. Un it
VI L Input Low Level
Voltage
(*)

- O 1.5 V

VI H Input High Level

Voltage (see note 1)
(*)

( s ) 3.5 V

V I(hyst.) Input Hysteresis

c t 0.2 0.85 1.5 V

I IN
Voltage
Input Current
d u VI N = 5 V Tc ase = 25 oC 100 µA

o
Pr
V ICL Input Clamp Voltage I IN = 10 mA 5 6 7 V
I IN = -10 mA -0.7 V

t e
(*) : The input voltage is internally clamped at 6 V about. It is possible to connect this pin to an higher voltage via an external resistor
provided the input current does not exceed 10 mA.

e
ol
SWITCHING (VCC = 13 V)
s
O bSymb ol
t d(on)
Parameter
Turn-on Delay Time Of I OUT = 5 A
Test Cond ition s
Resistive Load
Min.
25
Typ .
90
Max.
250
Un it
µs
Output Current Input Rise T ime < 0.1 µs T j = 25 o C
tr Rise Time O f O utput I OUT = 5 A Resistive Load 80 300 650 µs
Current Input Rise T ime < 0.1 µs T j = 25 o C
t d(of f) Turn-off Delay Time O f I OUT = 5 A Resistive Load 300 750 1500 µs
Output Current Input Rise T ime < 0.1 µs T j = 25 o C
tf Fall T ime Of Output I OUT = 5 A Resistive Load 80 200 400 µs
o
Current Input Rise T ime < 0.1 µs T j = 25 C
(di/dt) on Turn-on Current Slope I OUT = 5 A 0.02 0.05 A/µs
(di/dt) off Turn-off Current Slope I OUT = 5 A 0.02 0.05 A/µs

4/9
 VN460SP

ELECTRICAL CHARACTERISTICS (continued)

PROTECTIONS AND DIAGNOSTICS
Symb ol Parameter Test Cond ition s Min. Typ . Max. Un it
o
T TSD Thermal Shut-down 150 170 190 C
Temperature
o
T TR Thermal Reset 135 C
Temperature
o
T RSD Thermal Hysteresis 5 15 50 C
(HYST)

VENOL Output Voltage 8V≤VCC ≤30V 5.2 6.6 8 V

Authorizing Openload
Detection

( s )
ct
I OL Open Load Current 8V≤VCC ≤30V 100 800 1500 mA
Level
I OV Over Current R LOAD ≤10 mΩ
o o
25
d
50
u A
- 40 C<T Cas e<125 C
o
Pr
I AV Average Current in R LOAD ≤10 mΩ 5.4 A
o
Short Circuit T C = 85 C
V STAT Status O utput Voltage I STAT = 1.6 mA (Fault Condition)

e t e 0.4 V
V SCL Status Clamp Voltage I STAT = 10 mA
I STAT = -10 mA
ol 5.5 6
-0.7
7 V
V
t POL Status Delay (∗)
b s 50 300 950 µs

-O
t POVL Status Delay (∗) 10 µs
V DEMAG Turn-off Output Clamp I OUT = 5 A, L = 1 mH, VI N = 0 V CC -45 VCC -50 V CC -55 V
Voltage

( s )
ct
(∗) ISO definitions TPOL = Status delay in case of open load conditions
TPOVL = Status delay in case of over load conditions

d u
r o
e P
l e t
s o
O b

5/9
VN460SP

FIGURE 1

( s )
uct
SWITCHING PARAMETERS TEST CONDITIONS
o d
P r
e t e
o l
b s
- O
(s )
c t
d u
r o
e P
l
TRUTH TABLEe t
o
bs
Co nditi ons INPUT OUT PUT STAT US

O
Normal Operation

O ver-voltage
L
H
X
L
H
L
H
H
H
Under-voltage X L H
T hermal shut-down H L L
O pen load H H L
H = high level, L= low level, X= unspecified

6/9
 VN460SP

FIGURE 2: Switching Waveforms

( s )
uct
o d
P r
e te
o l
b s
- O
(s )
c t
d u
r o
e P
l e t
s o
O b

7/9
 VN460SP

PowerSO-10 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
A 3.35 3.65 0.132 0.144
A1 0.00 0.10 0.000 0.004
B 0.40 0.60 0.016 0.024
c 0.35 0.55 0.013 0.022
D 9.40 9.60 0.370 0.378
D1 7.40 7.60 0.291
s )
0.300

(
ct
E 9.30 9.50 0.366 0.374

u
E1 7.20 7.40 0.283 0.291
E2 7.20 7.60 0.283

o d 0.300

Pr
E3 6.10 6.35 0.240 0.250
E4 5.90 6.10 0.232 0.240
e 1.27

e t e 0.050

ol
F 1.25 1.35 0.049 0.053
H 13.80 14.40 0.543 0.567
h 0.50
b s 0.002
L 1.20
O
1.80 0.047 0.071

)-
q 1.70 0.067
o
α 8o
0

t ( s
u c
o d B

P r 10 6
0.10 A B

e t e
=

l
=

=
=

H E E2 E3 E1 E4

o
=
=

=
=

s
=

O b 1 5
SEATING
PLANE

e B DETAIL ”A” A

0.25 M C
Q
D
h = D1 =
= =
SEATING
PLANE
A
F
A1 A1

L
DETAIL ”A”

α
0068039-C

8/9
 VN460SP

Please Read Carefully:

( s )
u ct
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the

time, without notice.

o d
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any

All ST products are sold pursuant to ST’s terms and conditions of sale.

P r
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no

t e
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.

e
o l
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products

b s
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.

- O
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED

(s )
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS

t
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.

c
d u
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)

r o
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT

e P
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY

l e t
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.

s o
O b
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

© 2013 STMicroelectronics - All rights reserved

STMicroelectronics group of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com

DocID5691 Rev 3 9/9