www.atos.

com Table A160-11/E

Axial piston pumps type PVPC

variable displacement, by a full line of mechanical controls

PVPC are variable displacement axial

piston pumps for high pressure opera-
tion, with low noise level, suitable for
hydraulic oils or synthetic fluids having
symilar lubricating characteristics.
The actual displacement is dependent
on the lenght of stroke of the pumping
pistons 햲 . This lenght of stroke is
determined by the position of the swa-
shing plate 햳 that is achieved by two
servo pistons 햴 with differential areas,
against a spring 햵.
The rotating barrel 햶 forces the pistons
in a circular path in and out of the bar-
rel and fluid displacement takes place.
Typical section on side shows version
CH with manual pressure compensator
햷 and venting solenoid valve 햸.
The available hydraulic controls are
shown in sections . The wide range of
electrohydraulic proportional controls is
shown in tab. A170.
SAE J744 mounting flange and shaft
(see note 1).
Max displacement: 29-46-73-88 cm3/rev.
PVPC-CH-4046 Max pressure: 280 bar working
350 bar peak.

1 MODEL CODE
PVPC X2E – C – 4 046 / 31044 / 1 D -I X 24DC 10 /*
Variable displacement Synthetic fluids:
axial piston pump WG = water-glycol
PE = phosphate ester
See notes in section 
Eventual suffix for double pumps
X2E = with a fixed displacement
pump type PFE (see tab. A005) Series number

Type of control (see section ): Supply voltage, see section :

C = manual pressure compensator 00 = solenoid valve without coils (only for OI
CH = manual pressure compensator, with venting solenoid)
R = remote pressure compensator
L = load sensing (pressure & flow)
LW= constant power (combined pressure & flow) X = without connector
For electrohydraulic proportional controls, see See section  for available connectors, to be ordered
table A170 separately

Size:
3 = for displacement 029 Solenoid of pilot valve:
-I = solenoid OI (DHI) for AC and DC supply
4 = for displacement 046
5 = for displacement 073 and 090

Max displacement of axial piston pump: Direction of rotation (viewed at the shaft end)
029 = 29 cm3/rev D = clockwise
S = counterclockwise
046 = 46 cm3/rev
073 = 73 cm3/rev
090 = 88 cm3/rev Shaft (SAE Standard) (1):
1 = keyed (7/8” for 029 - 1” for 046 - 1 1/4” for 073 and 090)
Type of PFE (for double pumps), see tab. A005 5 = splined (13 teeth for 029 - 15 for 046 - 14 for 073 and 090)

1) pumps with ISO 3019/2 mounting flange and shaft (option /M) are available on request

2 OPERATING CHARACTERISTICS

Pump model PVPC-*-3029 PVPC-*-4046 PVPC-*-5073 PVPC-*-5090 External load position

Displacement [cm /rev]

3
29 46 73 88

Theoretical max flow at 1450 rpm [l/min] 42 66,7 105,8 127,6

Max working pressure / Peak pressure [bar] 280/350 280/350 280/350 250/315

Min/Max inlet pressure [bar abs.] 0,8 / 25 0,8 / 25 0,8 / 25 0,8 / 25

Max pressure on drain port [bar abs.] 1,5 1,5 1,5 1,5
Power consumption at 1450 rpm and at [kW] Fax = axial load
19,9 31,6 50,1 54,1
maximum pressure and displacement Frad = radial load
Type 1 Type 5 Type 1 Type 5 Type 1 Type 5 Type 1 Type 5
Max torque on the first shaft [Nm] Notes: For speeds over 1800 rpm the inlet port
200 190 230 330 490 620 490 620 must be under oil level with adequate pipes.
Max permissible load Fax 1000 1500 2000 2000 Maximum pressure for all models with option /WG is
[N]
on drive shaft Frad 1500 1500 3000 3000 160 bar, with option /PE is 190 bar.
Max speed with options /WG and /PE is
Speed rating [rpm] 600 ÷ 3000 600 ÷ 2600 600 ÷ 2200 600 ÷ 1850
2000/1900/1600/1500 rpm respectively for the four sizes.

A160
 3 MAIN CHARACTERISTICS OF VARIABLE DISPLACEMENT AXIAL PISTON PUMP TYPE PVPC

Installation position Any position. The drain port must be on the top of the pump. Drain line must be separated and
unrestricted to the reservoir and extended below the oil level as far from the inlet as possible.
Suggested maximum line lenght is 3 m.
Ambient temperature from -20°C to +70°C
Fluid Hydraulic oil as per DIN 51524...535; for other fluids see section 
Recommended viscosity 15÷100 mm2/sec at 40˚C (ISO VG 15÷100). Maximum start-up viscosity: 1000 mm2/sec
Fluid contamination class ISO 16/13 (filters at 10 µm value with ß10 ≥ 75 recommended)
Fluid temperature -20°C +60°C -20°C +50°C (seals /WG) -20°C +80°C (seals /PE)

3.1 Coils characteristics (for version CH)

Insulation class H
Connector protection degree IP 65
Relative duty factor 100%
Supply voltage and frequency See electric feature 
Supply voltage tolerance ± 10%

4 ELECTRIC CONNECTORS ACCORDING TO DIN 43650 FOR VERSION CH

The connectors must be ordered separately

Code of connector Function

SP-666 Connector IP-65, suitable for direct connection to electric supply source

SP-667 As SP-666 connector IP-65 but with built-in signal led, suitable for direct connection to electric supply source

5 ELECTRIC FEATURES FOR VERSION CH

External supply Power

(1) For other supply voltages available on
Type of Type of Colour of request see technical table E010.
nominal voltage ±10% consumption Code of spare coil
solenoid connector coil label (2) Coil can be supplied also with 60 Hz of
(1) (3)
voltage frequency: in this case the perfor-
6 DC SP-COU-6DC /80 brown mances are reduced by 10 ÷ 15% and
SP-666
DIRECT 12 DC SP-COU-12DC /80 green the power consumption is 55 VA.
or 33 W
CURRENT 24 DC SP-COU-24DC /80 red (3) Average values based on tests perfor-
SP-667
48 DC SP-COU-48DC /80 silver med at nominal hydraulic condition and
OI ambient/coil temperature of 20°C.
110/50 AC (2) SP-COI-110/50/60AC /80 yellow
SP-666 (4) When solenoid is energized, the inrush
ALTERNATE 120/60 AC SP-COI-120/60AC /80 white
or 60 VA (4) current is approx 3 times the holding cur-
CURRENT 230/50 AC (2) SP-COI-230/50/60AC /80 light blue
SP-667 rent. Inrush current values correspond to
230/60 AC SP-COI-230/60AC /80 silver
a power consumption of about 150 VA.

6 INSTALLATION POSITION

VERTICAL INSTALLATION
D2

D2 D2

D2
B

A
IN IN
C

IN
C

D1

The pump is supplyed whit drain D2 open, INSIDE THE TANK INSIDE THE TANK OUTSIDE THE TANK, above oil level
and D1 plugged. Before installation fill the
Minimum oil level equal or above the pump Minimum oil level below the pump moun- Minimum inlet pressure = 0,8 bar absolute
pump with hydraulic oil for at least 3/4 of its
mounting surface. ting surface. B  800mm, C= 200mm
volume, keeping it in horizontal position.
A  200mm Minimum inlet pressure = 0,8 bar absolute
With exception of pump mounted below the
B  800mm, C= 200mm
oil level, we recomend to interpose a baffle
plate between inlet and drain line.

HORIZONTAL INSTALLATION

D2
D2 IN
C

D2
D2
B

IN
C

IN IN

INSIDE THE TANK INSIDE THE TANK OUTSIDE THE TANK, above oil level OUTSIDE THE TANK, below oil level
Minimum oil level equal or above the pump Minimum oil level below the pump moun- Minimum inlet pressure = 0,8 bar (absolute) C= 200mm
mounting surface. ting surface. B  800mm, C= 200mm
A  200mm Minimum inlet pressure = 0,8 bar (absolute)
B  800mm, C= 200mm

IN: inlet line - D1: drain line - A: minimum distance between inlet and drain line - B+C: permissible suction height - C: inlet line immersion dept
 7 DIAGRAMS at 1450 rpm (based on mineral oil ISO VG 46 at 50°C)

7.1 Noise level curves

Ambient noise levels measured in compliance with ISO 4412-1 oleohydraulics -Test procedure to define the ambient noise level - Pumps
Shaft speed: 1450 rpm.

= Qmax = Qmin

PVPC-*-3029 PVPC-*-4046 PVPC-*-5073 and PVPC-*-5090

Noise level [dB]

Noise level [dB]

Noise level [dB]

Operating pressure [bar] Operating pressure [bar] Operating pressure [bar]

7.2 Operating limits

1 = Volumetric efficiency 4 = Power consumption with full flow
2 = Overall efficiency 5 = Power consumption at pressure compensation
3 = Flow versus pressure curve

PVPC-*-3029 PVPC-*-4046 PVPC-*-5073

1 1 1
Efficiency [%]

Efficiency [%]

Efficiency [%]
2 2
2
Power consumption [kW]

Power consumption [kW]

Power consumption [kW]

3 3

3
4
Flow [l/min]

Flow [l/min]

Flow [l/min]
4 4

5 5 5

Operating pressure [bar] Operating pressure [bar] Operating pressure [bar]

7.3 Response times PVPC-*-5090

7.3.1 Response times and pressure peack 1

due to variation 0% → 100% → 0% of
Pressure [bar]

Efficiency [%]

2
the pump displacement, obtained with

Power consumption [kW]

an istantaneously opening and shut-off
of the delivery line.
3
Pump type T1 (ms) T2 (ms)
αmax
Swashing plate angle

4
Flow [l/min]

PVPC-*-3029 31 19

PVPC-*-4046 44 20
5
PVPC-*-5073 50 25 αmin
PVPC-*-5090 53 28 Operating pressure [bar]

Time [ms]

7.3.2 Variation of inlet pressure and reduc-

tion of displacement with increasing
speed rating
Speed rating [rpm/rpmmax]

Inlet pressure [rbar abs.]

Displacement rating [cm3/cm3max]

A160
8 HYDRAULIC AND ELECTROHYDRAULIC CONTROLS

Hysteresis and pressure

increasing; max 4 bar
C Manual pressure compensator
The pump displacement decreases when the
line pressure approaches the setting pressu-
re of the compensator. The pump supplies

Flow [l/min]
only the fluid required by the system.
Pressure may be steplessly adjusted at the
pilot valve.
Compensator setting range: 20 ÷ 350 bar
(315 bar for 090)
Compensator standard setting: 280 bar
(250 bar for 090) Pressure [bar]

Hysteresis and pressure

CH Manual pressure compensator with ven- increasing; max 4 bar
ting
As C plus venting function, when a long
unloading time is required and heat genera-
tion and noise have to be kept at lowest

Flow [l/min]
level.
Compensator setting range: 20 ÷ 350 bar
(315 bar for 090)
Compensator standard setting: 280 bar
(250 bar for 090)
Pressure [bar]

Hysteresis and pressure

R Remote pressure compensator increasing; max 4 bar

햳 As C, but with remote setting of the compen-

sator by means of a pressure relief valve on
the piloting line X.
This version can be obtained from version L
Flow [l/min]

using a blind plug UNI 5923 M4x12 in pos.l햲

and a restrictor M4 drilled ø 0,75 mm in pos. 햳.
Compensator setting range: 20 ÷ 350 bar
(315 bar for 090)
햲 Compensator standard setting: 280 bar
(250 bar for 090) Pressure [bar]

not supplied Hysteresis and pressure

L Load sensing increasing; max 4 bar
The pump displacement is automatically adju-
sted to maintain a constant (load indipendent)
pressure drop across an external throttle.
Changing the throttle regulation, the pump flow
Flow [l/min]

is consequently adjusted.
Load sensing control always incorporates an
hydraulic compensator to limit the maximum
pressure.
Compensator setting range: 20 ÷ 350 bar
(315 bar for 090)
Compensator standard setting: 280 bar Pressure [bar]
(250 bar for 090)
Differential pressure setting range: 10 ÷ 40 bar
Differential pressure standard setting: 14 bar

not supplied
Maximum
LW Constant power power
curve
In order to achieve a constant drive torque
Theoretical
with varying operating pressure. The swashing power
Flow [% of max]

angle and therefore the outlet flow is varied so curve

that the product of flow and pressure remains
constant.
For the best regulation, minimum working pres-
Minimum
sure is 80 bar. power
While selecting LW control, the required value curve
of power must be communicated with the order
300
(ex. 10 kW at 1450 rpm). Pressure [bar]
9 DIMENSIONS OF PVPC-*-3029: BASIC VERSION “C” CONTROL

PORTS DIMENSION
IN = Flange SAE 3000 1 1/4”
OUT = Flange SAE 6000 3/4”
D1, D2 = 1/2” BSPP
햲 = Regulation screw for max displacement 1,5 cm3/rev per turn. Adjustable range 50% to 100% of max displacement.
In case of double pump the regulation screw is not always available, please contact our technical office.

INLET PORT OUTLET

PORT
IN
OUT

DRAIN PORT

DRAIN PORT

Mass: 18 kg

SHAFT TYPE “1” SHAFT TYPE “5”

SAE “B” SPLINED

13 TEETH 16/32 PITCH
30˚ INVOLUTE SPLINE

INTERMEDIATE FLANGE SAE “A” FOR PFE-31 INTERMEDIATE FLANGE SAE “B” FOR PFE-41

SAE “A” SPLINED SAE “B” SPLINED

9 TEETH 16/32 PITCH 13 TEETH 16/32 PITCH
100 Nm MAX 135 Nm MAX

OR-2325
OR-3400

Drawing shows pumps with clockwise rotation (option D): pumps with counterclockwise rotation (option S) will have inlet and outlet ports inverted

A160
10 DIMENSIONS OF PVPC-*-4046: BASIC VERSION “C” CONTROL

PORTS DIMENSION
IN = Flange SAE 3000 1 1/2”
OUT = Flange SAE 6000 1”
D1, D2 = 1/2” BSPP
햲 = Regulation screw for max displacement 2,2 cm3/rev per turn. Adjustable range 50% to 100% of max displacement.
In case of double pump the regulation screw is not always available, please contact our technical office.

OUTLET
INLET PORT PORT
IN OUT

DRAIN PORT

DRAIN PORT

Mass: 24 kg

SHAFT TYPE “1” SHAFT TYPE “5”

SAE “BB” SPLINED

15 TEETH 16/32 PITCH
30˚ INVOLUTE SPLINE

INTERMEDIATE FLANGE SAE “A” FOR PFE-31 INTERMEDIATE FLANGE SAE “B” FOR PFE-41

SAE “A” SPLINED

9 TEETH 16/32 PITCH SAE “B” SPLINED
135 Nm MAX 13 TEETH 16/32 PITCH
250 Nm MAX

OR-2325

OR-3400

Drawing shows pumps with clockwise rotation (option D): pumps with counterclockwise rotation (option S) will have inlet and outlet ports inverted
11 DIMENSIONS OF PVPC-*-5073 and PVPC-*-5090: BASIC VERSION “C” CONTROL

INLET PORT
OUTLET
IN PORT
OUT

DRAIN PORT

PORTS DIMENSION
IN = Flange SAE 3000 2”
OUT = Flange SAE 6000 1 1/4”
D1, D2 = 3/4” BSPP
햲 = Regulation screw for max displacement
3,2 cm3/rev per turn.
Adjustable range 50% to 100% of max DRAIN PORT
displacement.
In case of double pump the regulation screw
is not always available, please contact our
technical office.

Mass: 33 kg

SHAFT TYPE “1” SHAFT TYPE “5”

SAE “C” SPLINED
14 TEETH 12/24 PITCH
30˚ INVOLUTE SPLINE

INTERMEDIATE FLANGE SAE “A” FOR PFE-31 INTERMEDIATE FLANGE SAE “B” FOR PFE-41

SAE “A” SPLINED SAE “B” SPLINED

9 TEETH 16/32 PITCH 13 TEETH 16/32 PITCH
135 Nm MAX 330 Nm MAX

OR-2325
OR-3400

INTERMEDIATE FLANGE SAE “C” FOR PFE-51

SAE “C” SPLINED

14 TEETH 12/24 PITCH
440 Nm MAX

OR-3400

Drawing show pumps with clockwise rotation (option D): pumps with counterclockwise rotation (option S) will have inlet and outlet ports inverted

A160
12 DIMENSIONS OF PVPC: OTHER CONTROLS

VERSION CH VERSIONS L, R

VERSION LW

TIGHTENING TORQUE = 15 Nm max

햲 = Regulation screw for max displacement. Adjustable range 50% to 100% of max displacement).
In case of double pump the regulation screw is not always available, please contact our technical office.
Drawing shows pumps with clockwise rotation (option D): pumps with counterclockwise rotation (option S) will have inlet and outlet ports inverted and also the consequently
position of the control groups

Pump type Version A B C D E Mass (kg)

CH 168 111 - - - 22
PVPC-*-3029 L -R 144 111 100 - - 19,2
LW 144 111 - 211 104 20
CH 177 111 - - - 28
PVPC-*-4046 L -R 153 111 109 - - 25,2
LW 153 111 - 235 111 26
CH 190 111 - - - 36,9
PVPC-*-5073
L -R 166 111 122 - - 34,2
PVPC-*-5090 LW 166 111 - 258 120 35

10/10