1.

In permanent mold casting method

a. none of the above

b. molten metal is forced into mold under high pressure

c. molten metal is poured and allowed to solidify while the mold is revolving

d. molten metal is poured in a metallic mold, retained in the mold long enough for the outer skin to
solidify and finally mold is turned over to remove molten metal still in molten condition

2. Which one is true about Extrusion?

a. is used to improve fatigue resistance of the metal by setting up compressive stresses in its surface

b. is extensively used for making bolts and nuts

C. consists of pressing the metal inside a chamber to force it out by high pressure through an orifice
which is shaped to provide the desired form of the finished part

d. is used for reducing the diameter of round bars and tubes by rotating dies which open and close
rapidly on the work!

3. A eutectoid reaction involves which of the follöwing phases?

a. Oneiquid and one solid

b.Two liquid and one solid

c Three solid

d. One liquid and wosolid

4. A long, circular aluminium rod attached at one end to the heated wall and transfers heat through
convection to a cold fluid. (a) If the diameter of the rod is tripled, by how much would the rate of heat
removal change?

a, 200%

b. 520%

c. 100%

d. 25%

5. A material is said to be allotropic if it has

a. Different crystal structures at different temperatures

c. Any one of the above

d. Atoms distributed in random pattern

6. A reversible engine has ideal thermal efficiency of 20%. When it is used as a refrigerating machine
with all other conditions unchanged, the coefficient of performance will be

a. 1.23

b. 4.23

c. 2.83

d 333

7. A type I thermocouple is made of the following metals

a. Iron and Constantan

b. Aluminum and Tungsten

C. Platinum and Platinum/Rhodium alloy

d Copper and Constantan

8. At the solid-fluid convective interface the thermal conductivity of the solid and fluid are given as Ks =
2 Kf and the Biot number is 0.07. What is the value of the Nu

a. 0.28

b 0.14

c2

d 0.7

9. Corrosion resistance of steel is increased by addition of

a. Vanadium, aluminium

b. Tungsten, molybdenum, vanadium, chromium

c Sulphur, phosphorus, lead

d. Chromium and nickel

10. Dalton's law for ideal-gas mixtures, states that the pressure of a gas mixture is equal to the sum of
the pressures each gas would exert if.
A. It existed alone at the mixture pressures and volume

b. It existed alone at the mixture temperature and volume:

C. It existed alone at the mixture temperature only

d. It existed alone at the mixture temperature and pressures

11. From heat transfer rate concept related to a heat exchanger, if your design resulted a small value of
AT that leads to higher cost of the exchanger what will be your other options that can be implement and
reduce the cost of the construction of the heat exchanger

a. Selecting from a variety of exchanger designs that can minimize the product of overall heat transfer
coefficient and area

b. Increasing the area of the heat exchanger

c. Selecting higher flow rate on the heat transfer fluid side

d. Minimizing the heat transfer area by using fin

12. Heat transfer and work transfer are

a. energy interactions

b. all of the mentioned

c energy in the transit

d boundary phenomena

13. In a lithium bromide absorption refrigeration system

a. Ammonia is used as a refrigerant and lithium bromide as an absorbent

b. Water is used as a refrigerant and lithium bromide as an absorbent

C. Lithium bromide is used as a refrigerant and water as an absorbent

d. All

14. In a single point tool, the angle between the surface of the flank immediately below the point and a
line drawn from the point perpendicular to the base, is known as

a. End relief angle

b. Back rake angle

C. Side rake angle

15. In aircraft, the air refrigeration cycle is used because of

a. Low weight per ton of refrigeration

b. Low temperature at high altitudes

c High heat transfer rate

d. Higher coefficient of performance

16. In closed moving boundary system, a positive change in internal energy occur when,

a. Heat is added and work done is zero

b Heat is added and work is done by the system.

C. Heat is added and work is done on the system

d. Heat is removed and work is done by the system

17. In permanent mold casting method

a. none of the above

b. molten metal is forced into mold under high pressure

c. molten metal is poured and allowed to solidify while the mold is revolving

d. molten metal is poured in a metallic mold, retained in the mold long enough for the outer skin to
solidify and finally mold is turned over to remove molten metal still in molten condition

18. It's a graphical representation of all the equilibrium phases as a function of temperature, pressure,
and composition.

a. Phase

b. Phase diagram

c equilibrium

d. All

19. It's a One-dimensional defect around which some of the atoms are misaligned of

a. Dislocation

b. Vacancy
c. Point defect

d. Screw dislocation

20. Knowledge of the cutting forces and power involved in machining operations is important for the
following reasons EXCEPT

a. Power requirements must be known in order to enable the selection of a machine tool with adequate
electric power

b. The work-piece is capable of withstanding these forces without excessive distortion

C Machine tools can be properly designed to minimize distortion of the machine components

d. none the above

21. Loss of head due to friction is

a. Directly proportional to gravitational constant

b. Directly proportional to hydraulic radius

c. Inversely proportional to velocity

d. Inversely proportional to hydraulic radius

22. Potentiometer as a displacement sensor works on the principle of

a Hall Effect

b. Self Inductance

c Mutual Inductance

d. Variable Resistance Transduction

23. potentiometer may be used for

a. calibration of voltmeter

b. measurement of resistance

c. all of the above

d. calibration of ammeter

24. Process of forming metal powder by directing molten metal through an orifice after which it is break
into small particle using high pressure fluid is known as? of

a. Crushing
b. Atomization

c. Electrolysis

d. Reduction

25. Strain gauges are resistance devices in a Wheat stone bridge configuration________

A. which requires bridge completion circuitry and an excitation source

B. which neither requires bridge completion circuitry nor an excitation source

C which doesn't require bridge completion circuitry and an excitation source

d. which requires bridge completion circuitry but does not an excitation source

26. The chemical sensor in the washing machine is used

a. To measure the pH value of water

b. To measure the amount of water For drying operations

d. To count the quantity of detergent

27. The condition of refrigerant after passing through the condenser in a vapour compression system is

d. Wet vapour

a. Saturated liquid

b. Dry saturated vapour

c. Superheated vapour

28. The condition of refrigerant after passing through the condenser in a vapour compression system is

a. Saturated liquid

d. Wet vapour

b. Dry saturated vapour

C Superheated vapour

29. The continuous phase of a composite material is known as its

d dispersed phase

a. matrix phase
b. fiber phase

C. surrounding phase

30. The entropy of any closed system can increase in which of the following way?

a. both of the mentioned

b. dissipative effects or internal irreversibilities

C. by heat interaction in which there is entropy transfer

d. none of the mentioned

30. The extend of deformation due to mechanical twinning is______ than slip deformation.

A. Average

B. Larger.

C. Smaller

D. Equal.

31. The following types of materials are usually the most ductile

a. Body centered cubic lattice

b. Hexagonal close packed lattice

C. All of the above

d. Face centered cubic lattice

32. The function of shunt in an ammeter is to

c. by pass the current

d. none of the above

a. increase the resistance of ammeter

b. increase the sensitivity of the ammeter

33. The main function of Actuator is

a. To produce motion

b. Detect output
C. Detect the state of the system

D. Detect input

34. The purpose of heat treatment is to

d. Modify the structure of the material

a. Any one of these

b. Change grain size

c. Relieve the stresses set up in the material after hot or cold working

35. Thermoplastics are examples of

A. Ceramic matrix composites

b. Polymer matrix composites

C Carbon and graphite matrix composites

d. Metal matrix composites

36. Titanium is added to molten aluminium alloys before casting for the purpose of

a. increasing corrosion resistance

b. reducing porosity

c. improving fluidity

D. Grain refinement

37. Two streams of liquid metal which are not hot enough to fuse properly result into a casting defect
known as

a. Cold shut

b. Sand wash

c. Scab

d. Swell

38. What are transducers?

a. They convert work from one form to another

b. They convert work to power

d. They convert power from one form to another

39. What is fluid mechanics used for

a. To comprehend the behaviour of solid fluids under pressure

b. To comprehend the behaviour of fluids under a variety of forces & atmospheric conditions

C. None of the mentioned

d. To comprehend the behaviour of fluids under various temperatures only

40. What is the principal cause of action of buoyant force on a body submerged partially or fully in fluid?

a. Internal shear forces mitigating external forces

b. Displacement of fluid due to submerged body

c. None of the mentioned

d. Development of force due to dynamic action

41. What is the relationship between Kelvin-Planck's and Clausius statements? of

a. violation of one doesn't violate the other

b. virtually two parallel statements of the second law

c none of the mentioned

d. not connected to each other

42. What is the type of joining process called, where the parts to be welded are kept in contact and
rotated relative to each other and axial pressure is applied when the desired temperature is obtained?

a. Friction welding

b. Electron beam welding

c Ultrasonic welding

d. Forge welding

43. What is the type of welding defect caused due to poor deposition of weld rod is called?

a Porosity

b. Crack
c. Undercut

d. Under fill

44. When a fluid is subjected to resistance, it undergoes a volumetric change due to

a. Strain

b. Adhesion

c. Compressibility

d. Cohesion

45. When the fluid flows over solid surface and the boundary condition is given as a No-slip condition,
what is the relative velocity of the fluid /solid interface?

A.5

b. None

C. 0

d. Free stream velocity

46. When the lower temperature of a refrigerating machine is fixed, then the coefficient of performance
can be improved by

a. Operating the machine at higher speeds

b. Lowering the higher temperature

C. Raising the higher temperature

d. Operating the machine at lower speeds

47. When the reference junction is the same temperature as the measurement junction in a
thermocouple circuit, the output voltage (measured by the sensing instrument) is;

a. Reverse polarity

b. Zero

C. Noisy

d. AC instead of DC

48. Which among the following is a correct statement regarding "Mechatronic system"?

a. More output in less time

c. Its initial cost of setup is low

d. Any individual can operate these system

49. Which of the following is true according to Clausius's statement?

a. none of the mentioned

b. it is impossible to construct a device that can transfer heat from a hotter body to a cooler body
without any effect

c it is impossible to construct a device that can transfer heat from a cooler body to a hotter body
without any effect

d. it is possible to construct a device that can transfer heat from a cooler body to a hotter body without
any effect

50. Which of the following method is most commonly used in fluid mechanics for analysis?

a. Lagrangian method

b. None of the mentioned

c. Control volume analysis

D. Eulerian Method

51.Which of the following part of mechanics deals with study of crack propagation?

a. Solid mechanics

b. Fracture mechanics

C Applied mechanics

d. Fluid mechanics

52. Which of the following process is used in winter air conditioning?

a Dehumidification

b. Cooling and Dehumidification

c Heating and Humidification

d. Humidification

53. Which of these statements is correct about machining?

b. Power required drops as metal temperature and cutting velocity increase.

C. All of the above

d. We can use the quantity of metal removed by it to estimate the required horsepower of a machine
tool.

54. Which one of the following is a formula for a closed system adiabatic process

a.Q-W=0

b.Q=AU

C. Q-W=AU

d. WAU

55. Why Wheatstone bridge is generally used in DC circuit?

a. To determine inductance

b. To determine capacitance

C To determine flux.

d. To determine resistance